REPAIR REPLACEMENT OF DISTRIBUTION AND RISING MAINLINES ALONGWITH SUBMERSIBLE, CENTRIFUGAL, JET, VT PUMP SETS AND CONTROL PANELS UNDER GE SAUGOR

Amount

M&L for taking out submersible pumpset of 1 to 7.5 HP capacity from open well / bore well by disconnecting submersible cable connection and delivery pipe line using tripoid chain pulley or any other means, dismantling from MS/GI/HDPE/UPVC pipe, opening pump set for carrying out repairs connecting back to MS/GI pipe and lowering the submersible pumpset into open well / bore well in original position after repairs complete all as specified and as directed . Note: (a) Unit rate quoted shall be deemed to included the labour for taking up & lowering the submersible pump from bore well along with delivery pipe. (b) Repairs / rewinding & servicing of submersible pump shall be measured under relevant items. (c) Spares parts required shall be measured and paid separately under relevent items.

M&L for taking out submersible pumpset of 9 to 30 HP capacity from open well / bore well by disconnecting submersible cable connection and delivery pipe line using tripoid chain pulley or any other means, dismantling from MS/GI/UPVC pipe, opening pump set for carrying out repairs connecting back to MS/GI/UPVC pipe and lowering the submersible pumpset into open well / bore well in original position after repairs complete all as specified and as directed. Note: (a) Unit rate quoted shall be deemed to included the labour for taking up & lowering the submersible pump from bore well along with delivery pipe. (b) Repairs / rewinding & servicing of submersible pump shall be measured under relevant items. (c) Spares parts required shall be measured and paid separately under relevent items.

M&L for opening up submersible/open well the following capacity motor, taking out burnt out winding, cleaning the slots with CTC and rewinding the same with new PVC insulated copper winding wire of existing gauge and turns, assembling back into position by using new suitable studs etc., oiling and greasing and fixing back into position for making motor fully functional, applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer, testing for satisfactory running complete all as specified and directed Note:-(i). The spare parts to be replaced shall be measured and paid separately . (ii). Lowering and lifting charges shall be measured and paid separately

01 HP Capacity Motor

03 HP Capacity Motor

5/6 HP Capacity Motor

7.5/9/10 HP Capacity Motor

15/20 HP Capacity Motor

30 HP Capacity Motor

M&L for opening centrifugal motor the following capacity motor , Taking out damaged/burnt out winding from single phase /three phase motor, cleaning the slots with CTC and rewinding the same with new super enamelled copper winding wire of existing gauge and turns, oiling and greasing and fixing back into position for making motor fully functional and testing for satisfactory running complete all as specified and directed Note:-The spare parts to be replaced shall be measured and paid separately

01 HP Capacity Motor

03 HP Capacity Motor

5/6 HP Capacity Motor

7.5/9/10 HP Capacity Motor

12.5/15/20 HP Capacity Motor

30/40 HP Capacity Motor

M&L for opening submersible pump the following capacity , carrying out repairs, reconditioning of spare parts such as impellers, thrust bearing with plate, shaft etc., by metalling and machining to their original shape and size, assembling back into position by using new suitable gland/rubber packing including studs, flanges, bolts and nuts etc., oiling and greasing for making pumpset fully functional, applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer, testing for satisfactory running complete all as specified and directed Note:-The spare parts to be replaced shall be measured and paid separately

01 HP Capacity Motor

03 HP Capacity Motor

5/6 HP Capacity Motor

7.5/9/10 HP Capacity Motor

15/20 HP Capacity Motor

30 HP Capacity Motor

M&L for dismantling centrifugal pumpset/Jet pump of the following capacity , suitable for carrying out repairs, replacement of worn out parts such as impellers, bearings, gland metal bushes etc., and reconditioning of spare parts such as shaft, impellers, housing body, bearing gland plate etc., by metalling and machining to their original shape and size and assembling back into position by using new suitable gland dory, gland plate, gland/rubber packing including studs/gland bolts and nuts, coupling bushes etc., oiling and greasing for making pumpset fully functional and testing complete all as specified and directed Note:-The spare parts to be replaced shall be measured and paid separately.

01 HP Capacity Motor

03 HP Capacity Motor

5/6 HP Capacity Motor

7.5/9/10 HP Capacity Motor

12.5/15/20 HP Capacity Motor

30/40 HP Capacity Motor

Supply only the items of following pump sets/motors complete all as specified and directed:-

NDE/DE Ball bearing suitable for upto 1 HP Capacity motor. Make:-TATA/SKF

NDE/DE Ball bearing suitable for 2/3 HP Capacity motor. Make:-TATA/SKF

NDE/DE Ball bearing suitable for 5 HP Capacity motor. Make:-TATA/SKF

NDE/DE Ball bearing suitable for7.5/10 HP Capacity motor. Make:-TATA/SKF

NDE/DE Ball bearing suitable for 12.5/15 HP Capacity motor. Make:-TATA/SKF

NDE/DE Ball bearing suitable for30/40 HP Capacity motor. Make:-TATA/SKF

Stainless shaft suitable for centrifugal pump 7.5/10 HP Capacity

Stainless shaft suitable for centrifugal pump 12.5/15 HP Capacity

Stainless shaft suitable for centrifugal pump 30/40 HP Capacity

Gun metal thrust bearings suitable for 7.5/10 HP Capacity Pump set

Gun metal thrust bearings suitable for 12.5/15 HP Capacity Pump set

Gun metal thrust bearings suitable for 30/40 HP Capacity Pump set

SS Shaft with Key Suitable for Submersible pump set 1 HP Capacity

SS Shaft with Key Suitable for Submersible pump set 3 HP Capacity

SS Shaft with Key Suitable for Submersible pump set 5/6 HP Capacity

SS Shaft with Key Suitable for Submersible pump set 7.5/9 HP Capacity

SS Shaft with Key Suitable for Submersible pump set 15 HP Capacity

SS Shaft with Key Suitable for Submersible pump set 20 HP Capacity

Impeller made out bronze suitable for 1 HP Capacity Submersible pump

Impeller made out bronze suitable for 3 HP Capacity

Impeller made out bronze suitable for 5/6 HP Capacity

Impeller made out bronze suitable for 7.5/9/10 HP Capacity

Impeller made out bronze suitable for 15/20 HP Capacity

Impeller made out bronze suitable for 30 HP Capacity

Pump bush lower and upper alongwith sleeves made out bronze as per the sample suitable for 1 HP Capacity Submersible pump set

Pump bush lower and upper alongwith sleeves made out bronze as per the sample suitable for 3 HP Capacity

Pump bush lower and upper alongwith sleeves made out bronze as per the sample suitable for 5/6 HP Capacity

Pump bush lower and upper alongwith sleeves made out bronze as per the sample suitable for 7.5/9/10 HP Capacity

Pump bush lower and upper alongwith sleeves made out bronze as per the sample suitable for 15/20 HP Capacity

Pump bush lower and upper alongwith sleeves made out bronze as per the sample suitable for 30 HP Capacity

CI impeller suiable for Centrifugal/Jet pump set upto 1 HP Capacity pump set as per sample

CI impeller suiable for Centrifugal/Jet pump set 2/3 HP Pump set

CI impeller suiable for Centrifugal/Jet pump set 5 HP Pump set

CI impeller suiable for Centrifugal/Jet pump set 7.5/10 HP Pump set

CI impeller suiable for Centrifugal/Jet pump set 12.5/15 HP Pump set

CI impeller suiable for Centrifugal/Jet pump set 30/40 HP Pump set

Taking down VT pump set of capacity 120 HP from Chittora pump house from Jack well and dismantling the after disconnection the holo shaft motor from the pump set and suction line with connected items line shaft of turbine pump set items such as impellers,bushes ,spider assembly etc and reassembling after necessory repair grinding/lathe work / replacement of the worn out items and testing complete and fixing at the site including transportation from Chittora pump house to contractor's work shop and back. Note:-(i) Replacement of defective parts shall be measured & paid separately under respective items as "Supply only" (ii) Labour element is included in the rate and make of part shall be as per existing make (iii) The quoted rate included for shifting of parts/motor/pump for repair grinding/lathe work / replacement from Pump house to contractor's work shop and back

Supply only the following items suitable for VT pumpset of 120 HP capacity complete all as specified and directed:-

Impeller made out of MS with impeller key

Impeller shaft coupling

Bush of top impeller made out of steel with impeller key

Line shaft and replacement of the Line shaft coupling

Sleeves made out of bronze

Spider assy with bearing holder flanged

Stud bolt with washer

Bearings (DE/NDE)

Bush made out of bronze

Rubber bush

Taking down the Holo shaft slip ring induction motor of capacity 135 HP from VT Pump and Dismantling carbon bush holder, carbon bush and slip ring assy with connected items and rewinding with original guage of copper winding wire insulation material and terminal plate and copper sturds and reasssemble & testing proper aligment after necessory repair and repair/replacement of the following items paid separately here as after and reassembling after necessory repair grinding/lathe work / replacement of the worn out items and testing complete and fixing at the site including transportation from Chittora pump house to contractor's work shop and back. Note:-(i) Replacement of defective parts shall be measured & paid separately under respective items as "Supply only" (ii) Labour element is included in the rate and make of part shall be as per existing make (iii) The quoted rate included for shifting of parts/motor/pump for repair grinding/lathe work / replacement from Pump house to contractor's work shop and back

Supply only the following items suitable for induction motor of capacity 135 HP complete all as specified and directed:-

Slip ring assy complete with studs made out of copper as per sample kept in AGE E/M office.

Carbon brushes holder made of bronze as per existing sizes per sample kept in AGE E/M office.

Carbon brushes as per existing size and s per sample kept in AGE E/M office.

Taking down Mud pump set set of capacity 25HP from Chittora pump house from Jack well and Dismantling the after disconnection the holo shaft motor from the pump set and suction line with connected items line shaft of turbine pump set items such as impellers,bushes ,spider assembly etc and reassembling after necessory repair grinding/lathe work / replacement of the worn out items and testing complete and fixing at the site including transportation from Chittora pump house to contractor's work shop and back. Note:-(i) Replacement of defective parts shall be measured & paid separately under respective items as "Supply only" (ii) Labour element is included in the rate and make of part shall be as per existing make (iii) The quoted rate included for shifting of parts/motor/pump for repair grinding/lathe work / replacement from Pump house to contractor's work shop and back

Supply only the following items suitable for Mud pump set set of capacity 25HP complete all as specified and directed:-

Impeller made out of bronze with impeller key

Bowl bearing of top impeller made out of bronze with impeller key

Impeller shaft coupling

Line shaft and replacement of the Line shaft coupling

Sleeves made out of bronze

Spider assy with bearing holder flanged

Stud with nut

Bearing

Oil scement set of 08

Bearing

Bush made out of bronze

Rubber bush

Taking down the Holo shaft slip ring induction motor of capacity 120 HP from VT Pump and rewinding with original guage of copper winding wire insulation material and terminal plate and copper sturds and reasssemble & testing proper aligment after necessory repair and repair/replacement of the following items paid separately here as after and re-assembling at jack well chittora pump house .Including transporation from chittora pump house to work shop and back. Note:-(i) Labour element is included in the rate and Make of part shall be existing

Taking down VT pump set of capacity 135/120 HP from Chittora pump house from Jack well and dismantling the after disconnection the holo shaft motor from the pump set and suction line with connected items line shaft of turbine pump set items such as impellers,bushes ,spider assembly etc and reassembling after necessory repair grinding/lathe work / replacement of the worn out items and testing complete and fixing at the site including transportation from Chittora pump house to contractor's work shop and back. Note:-(i) Replacement of defective parts shall be measured & paid separately under respective items as "Supply only" (ii) Labour element is included in the rate and make of part shall be as per existing make (iii) The quoted rate included for shifting of parts/motor/pump for repair grinding/lathe work / replacement from Pump house to contractor's work shop and back

Supply only the following items suitable for VT pump set of capacity 135/120 HP complete all as specified and directed:-

Iimpeller made out of MS with impeller key

Iimpeller shaft coupling

Bush of top impeller made out of steel with impeller key

Line shaft and replacement of the Line shaft coupling

Sleeves made out of bronze

Spider assy with bearing holder flanged

Stud bolt with washer

Bearing NU-318C

Bearing 6316

Bush made out of bronze

Rubber bush

Taking down the existing slip ring induction motor of capacity 260 HP from cenrifugal pump set taking down pump and reassemble the same after aligment and dismantling carbon bush holder, carbon bush and slip ring assy with connected items after necessory repair and repair/replacement of the following items paid separately here as after and re-assembling at Berthuma pump house complete all as directed at site. Note:-(i) Replacement of defective parts shall be measured & paid separately under respective items as "Supply only" (ii) Labour element is included in the rate and make of part shall be as per existing make

Supply only the following items suitable for induction motor of capacity 260 HP complete all as specified and directed:-

Slip ring assy complete with sturds made out of copper as sample Kept in AGE E/M Office

Carbon bush holder made of bronze as per sample kept in AGE E/M Office

Carbon bush as per existing size as per sample kept in AGE E/M Office

Pump shaft as per sample kept in AGE E/M Office

M&L for dismantling centrifugal pumpset suitable for 260/240/220 HP for carrying out repairs, replacement of worn out parts such as impellers, bearings, gland metal bushes etc., and reconditioning of spare parts such as shaft, impellers, housing body, bearing gland plate etc., by metalling and machining to their original shape and size and assembling back into position by using new suitable gland dory, gland plate, gland/rubber packing including studs/gland bolts and nuts, coupling bushes etc., oiling and greasing for making pumpset fully functional and testing for satisfactory running complete all as specified and directed by Engineer -in Charge Note :-(i)The spare parts to be replaced shall be measured and paid separately under respective items as "Supply only" (ii) Labour element is included in the rate and make of part shall be as per existing make

Supply only the following items suitable for centrifugal pumpset suitable for 260/240/220 HP complete all as specified and directed:-

NDE /DE Ball bearings as per the sample kept in AGE E/M Office

Metal Coupling (Both side)

Gun metal bush as per the existing sample

Stud bolt and Nuts and with Washers

SS Shaft

M&L for opening induction motor of capacity 260/240/220 HP Capacity from Berthuma pump House taking out damaged/burnt out winding from Slot, cleaning the slots with CTC and rewinding the same with new super enamelled copper winding wire of existing gauge and turns, oiling and greasing and fixing back into position for making motor fully functional and testing for satisfactory running complete all as specified and directed by the Engineer in charge Note :- (i) The spare parts to be replaced shall be measured and paid separately under respective items as "Supply only" (ii) Labour element is included in the rate and make of part shall be as per existing make

Taking out the existing DOL starter, 415V, 3 Ph, 50 Hz from panel suitable for up to 5 HP Capacity motor , cleaning the electronic parts from inside, refixing the OLR, Contactor, NVC and SPP complete all as specified and directed Note :- Quoted rate shall be deemed to included the replacement of spares and making serviceable condition

All as per Srl item No. 22.00 here in before for suitable for 7.5 HP Motor

Taking out the existing Star-delta starter the following capacity motor from panel, cleaning the electrnic parts from inside, refixing the OLR, Contactor, NVC,and SPP connecting link wires complete all as specified and directed :- Note:-Quoted rate shall be deemed to included the replacement of spares and making serviceable condition

Suitable for 12.5 HP Motor

Suitable for 15/20 HP Motor

Suitable for 30/40 HP Motor

S&F DOL starter 415V, 50Hz, 3 Phase suitable for Upto to 7.5HP Motor, including replacement of copper lugs as per suitable and making suitable mounting on wall/floor stand with angle bolt,nut with wahsers as per size all as specified and directed

S&F Star delta starter 415V, 50Hz, 3 Phase of the following capacity motor including replacement of copper lugs as per suitable and making suitable mounting on wall/floor stand with angle bolt,nut with wahsers as per size complete all as specified and directed:-

Suitable for 12.5 HP Motor

Suitable for 15/20 HP Motor

Suitable forr 30/40 HP Motor

M&L for disconnecting cable connection from exiting starter suitable for 260/220 HP Capacity motor at Berthuma Pump house, 415V, 3 Phase,50Hz and replacement of the ML-12- 1No, & ML-10 -1 No contactor, Timer, Relay as per the existing capacity including rewiring complete and reassembling & testing and commisssioning complete all as specified and directed

Supply only the following items suitable for centrifugal pumpset suitable for 260/220 HP Capacity motor complete all as specified and directed:-

ML-12 Contactor

ML-10 Contactor

Supply only the following for the various water supply items:-

Rubber insertion Sheet 2 to 4 mm thick

Bufflo leather for foot valve 6mm thickness per sample

Multipurpose Grease

Cotton Waste

CI Foot Valve suitable for 50 mm dia as per sample

CI Foot Valve suitable for 80 mm dia as per sample

CI Foot Valve suitable for 100 mm dia as per sample

CI Foot Valve suitable for 150 mm dia as per sample

Lead Pig

Rubber insertion Sheet 2 to 4 mm thick

Lead wool

Synthetic insulating mat of size 2mx1mx10mm with IS 15652:2006& ISI Marked

Synthetic insulating Mat o size 2mx1mx12 mm with IS 15652:2006& ISI Marked

MS bolt, Nut with washers in different sizes and different length

M&L for disconnecting the cable connection from existing panel board/Starter/Busbar cutting the burried cable portion and replace the suitable size of Aluminium cable lugsof size 400 Sqmm and making serviceable connection testing and commissioning complete all as specified and directd

All as per item ser. No 30 here in before but 185 Sqmm

Removing the wooden sleepers from the slots /opening of the anicut across the river Bewas at Chittora in the lean season and stacking them separately for their serviceability after applying black oil to serviceable sleepers and unserviceable sleepers shall be stacked properly for inspection complete all as specified and directed

M&L for new second class hard wood (well seasoned) wooden sleeper of size 150mm x 100 mm (cross sectional size) and not less than 1475 mm (59") long duly tapered at end for easy insertion in the slots complete with and including 02 Nos eye hooks made out of MS plain round bar 20 mm dia, 400 mm long for each hook and the dia of hook shall be 50 mm, the other end of the round bar shall be tapered and fixed in wooden sleeper with and including applying a coat of coal tar on entire surface of sleepers complete all as specified and directed

Refixing of wooden sleepers which are stacked at Chittora pump house in the slots of Anicut and tide with 18 SWG GI wire to protect the wooden sleepers with and including applying a coat of coal tar on entire surface of sleepers , from washing out in heavy water current upto a level of 16 feet from bottom to anicut. Note:- Serviceable wooden sleepers obtained from Srl item No. 32 above shall be re-used in this item

M&L for black cotton/ yellow soil as required in water condition to fill the gap of two sleepers in the slots of the maximum height 16 Feet to avoid the leakage/seepage of water entire contract period complete all as specified and directed. Note:- (a) Contractor shall be responsible for filling of black cotton soil in between gap of two sleepers of the slot upto 16 mtr height without any leakage as per directions of Engineer in Charge (b) Entire quantity of BC soil shall be delivered by Contractor before monsoon & shall be stacked properly at a distance of 20 mtr away from river as per directions of Engr-in-Charge. (c) Opening of slots for release of water to Dhana and closing the anicut slots as per direction of Engineer-in-Charge without any extra cost d). The quoted rate shall be deemed to be included to provide safty belt / ladder etc as required at site.

Removing the silt/rubbish deposited on the other side of the anicut and depositing at a place not more than 50 mtrs and removing as directed by Engr-in-Charge. Note:-The silt/rubbish shall be stacked properly for measurement purpose all as directed.

Cutting and removing the washed out deposit at anicut trees/tree branches during the monsoon and before closing the anicut. The trees /tree branches obtained from the river shall be weighed. Note:-The weighing of wood shall be contractors responsibility and no extra shall be payable to him on this account.

M&L for cutting of vegetation,bushes grass etc surrounding the pump house,power house and OHT/ Sump area at various installations and removing to a distance of 50 mtr complete all as specified and directed.

SHRI RAM ELECTRICALS ENTERPRISES

SAGAR MOTOR AND TRACTOR CO

shubhanshu traders