SPECIAL REPAIRS TO ROOF OF BLDG Nos. E 38 AND T 1 OF PC WING, SPECIAL REPAIRS TO BLDG Nos. T 58 AND T 2 OF MT DET, ADDN ALTN TO TOILET BLOCK OF BLDG No. SP 1 A DS MESS AND SPECIAL REAPIRS TO WK SHOP BLDG No. E 6 AT MT YARD UNDER GE BELGAUM

Amount

Demolition of plain cement concrete in ground floors and pavings n. exc. 15cm thick, below or above GL all as specified and directed.

Demolition of plain cement concrete of any description and in any position, not otherwise specifically provided for all as specified and directed.

Demolition of brick work or stone masonry built in cement mortar or lime cement mortar including all quoins, arches, pillars, etc. but excluding precast concrete articles, in any position below or above ground level all as specified and directed.

Demolition of PCC block masonry built in cement mortar or lime cement mortar in any position below or above ground level all as specified and directed.

Cutting holes into or through stone walls built in cement mortar superficial area exc. 150 sqcm but n.exc. 400 sqcm each including making good in cement mortar 1:3 of cement concrete 1:2:4, type B-1 all as specified and as directed.

Taking down chowkhat with shutters (without taking off shutters from the frame) area n exc 1.5 Sqm each all as specified and directed.

Taking down chowkhat with shutters (without taking off shutters from the frame) area exc 1.5 Sqm and n exc 4 Sqm each all as specified and directed.

Dismantling timber scantling 40 Sq.cm and over in section in any position in un-framed work all as specified and directed.

Dismantling timber fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section all as specified and directed.

Dismantling boarding of any description fixed in any position with nails all as specified and directed.

Dismantling wrought iron or mild steel work of any description and in any position all as specified and directed.

Dismantling of single layer Mangalore pattern or similar tiles in roofing all as specified and directed.

Dismantling of corrugated or semi corrugated Asbestos Cement sheets in roof coverings including ridges, valley gutters, etc. all as specified and as directed.

Dismantling of plain or corrugated steel sheets of any gauge and thickness, in roof coverings, valleys, gutters, etc. all as specified and as directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., (measured overall as fixed along the centre line over fittings and accessories)

Dismantling wall and ceiling boards or insulation boards/ slabs of any thickness including cover fillets all as specified and as directed.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing, rubbish off the premises all as specified and directed.

Demolition of stone slab and tiles of any description and any thickness in floors laid, bedded and pointed in any mortar all as specified and directed.

Taking down cement plaster on brick or stone wall or ceiling concrete etc. including racking out joints hacking for key scrubbing down with water etc., all as specified and directed.

Taking up or down existing unserviceable 15mm bore GI tubes of any grade and making good disturbed surfaces all as specified and directed.

Taking up or down existing unserviceable 20mm bore GI tubes of any grade and making good disturbed surfaces all as specified and directed.

Excavation in trenches n. exc. 1.5 m wide and n. exc. 1.5 m depth for foundation, etc. and getting out in soft/ loose soil all as specified and directed.

Excavation in trenches n. exc. 1.5 m wide and n. exc. 1.5 m depth for foundation, etc. and getting out in hard/ dense soil all as specified and directed.

Returning filling in including spreading levelling, watering and well ramming in layers n. exc. 25 cm thick all as specified and directed.

Removing excavated soil n.exc 100m and depositing where directed at a level n. exc. 1.5 m above the starting point in soil all as specified and directed.

M&L for pre-cast cement concrete solid block masonry, exc 10 cm width, blocks cast in PCC 1:3:6, type C0, using 12.5 mm graded stone aggregate and setting in CM 1:6 all as specified and directed.

M&L plain cement concrete 1:3:6, type C1, using 20mm graded stone aggregate as in coping, bed blocks, eves filling between wall and tile/ sheet roofing including necessary form work all as specified and directed

M&L for providing precast cement concrete 1:2:4, Type B1, using 20mm graded stone aggregate, as in kerbs, with rounded or chamfered edges including all mouldings, set in cement mortar 1:6 including demolition of existing kerbs of any description and size all as specified and as directed.

Supply only approved integral water proofing compound all as specified and as directed.

M&L for 2nd class hard wood in scantling, clean sawn fixed in unframed work all as specified and directed.

Fixing only serviceable timber scantling of any description obtained from dismantling in un-framed work all as specified and directed.

M&L for 2nd class hard wood plain fillets, square, rectangular or triangular in section, wrought, secured with nails or beads; sectional area exc 13 and n.exc 25 Sq.cm all as specified and directed.

Fixing only serviceable timber fillets of any description obtained from dismantling, secured with nails or beads; sectional area exc 13 and n.exc 25 Sq.cm all as specified and directed.

M&L for 2nd class hard wood chowkhat or frames, plain, solid, wrought, framed and rebated on the solid rounded or chamfered, put together with glue pinned at joints, fixed in position all as specified and directed.

M&L for 35 mm thick second class hard wood, Plain framed, panelled shutter (two panel) with lock rail and panel of 12mm thick plywood BWR 7 ply with commercial veneers on both faces with size of rails and stiles sizes of members of shutters as specified in SSR Part I, Section 8. Clause 8.24 (a) and fitted to chowkats all as specified and as directed.

M&L for 35mm thick 2nd class hard wood glazed/ gauged shutters, open rebated and prepared to receive glass, gauze, etc. (divided into square with plain, chamfered or rounded, mitred and rebated sash bars any numbers), edge of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.24 (a) and fitted to chowkats all as specified and as directed.

M&L for aluminium frame work as in doors, partitions, windows and ventilators using powder coated aluminium sections including provision of glazing clips, hinges, handles, etc all as specified and as directed. Notes: (i) All the aluminium sections provided under this item shall be measured and converted into weight for payment with the designated unit weight mentioned in the manufacturer's catalogue for the corresponding aluminium sections/ fittings. (ii) The rate quoted deemed to include necessary grouting/ embedding of the aluminium frames/ supports into floors/ walls and making good the disturbed surfaces to match with the existing surfaces and provision of necessary gaskets. (iii) Particle board/ glass panels/ wire mesh shall be measured and paid separately.

M&L for aluminium sliding windows (Triple track), fabricated to required size with standard aluminium anodised sections, with bottom track of size 92 x 31.75 x 1.6mm, side and top frame of size 92 x 31.75 x 1.4mm, top and bottom shutter rail of size 39x17x1.4mm, outer style of size 39 x 17 x 1.4mm, interlock style of size 39 x 27 x 1.4mm, including provision of 4mm sheet glass ordinary quality for panels including provision of all hardware fittings such as handles, locking arrangements, rubber gaskets, rollers, spring catchers etc. complete all as specified and directed.

M&L for 18mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination on the other side with white lamination, as in cub board shelves/ cabinet works fixed with screws, fixed in repairs all as specified and directed

S&F MS butt hinges 100mm in size, medium weight, cold rolled all as specified and directed.

S&F extruded anodised aluminium alloy butt hinges 100mm in size, type B-21, with galvanised mild steel hinge pin all as specified and directed.

S&F aluminium anodised barrel tower bolt 100mm size all as specified and directed.

S&F aluminium anodised barrel tower bolt 150mm size all as specified and directed.

S&F 125 mm long extruded section aluminium alloy anodised handles fabricated type all as specified and directed.

S&F 150 mm long extruded section aluminium alloy anodised handles fabricated type all as specified and directed.

S&F 300mm long aluminium anodised sliding door bolt with hasp, staple (bolt type) and fixing clip of sheet cast or extruded section and fixing bolts plate type with bright bolt not less than 12mm dia all as specified and directed.

S&F in repairs Mild steel powder coated curtain rods with end designer caps, fancy type, 25mm dia all as specified and as directed.

S&F in repairs stainless steel brackets, suitable for holding 25mm dia single curtain rods, fixed to wall with necessary screws including drilling and plugging the holding screws and making good the wall surfaces all as specified and directed.

S&F Harrison rails, anodised aluminium alloy, with fixing brackets, stops, rollers etc. all as specified and as directed.

S&F brass knobs, 40mm dia fixed with nut and screw and washer all as specified and directed.

S&F in repairs hat and coat hooks, solid brass body, 175mm to 250mm size fixed with brass screw and washer all as specified and directed.

M&L for 2nd class hard wood small fittings such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including all necessary' labours; articles exc. 200 cu.cm but n exc 500 cu. cm each all as specified and as directed.

S&F in repairs stainless steel wire cloth 0.36 mm nominal dia of wire & average width of aperture 1.40mm fixed in panel of joinery with stainless steel wire staples all as specified and directed.

M&L for rolled mild steel sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters, fixed with angle cleats or other connecting plates conforming to Fe-410-W Gde-E-250 quality-A all as specified and as directed.

S&F mild steel framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; frame work of water tanks and similar work conforming to Fe-290 Gde- E-165 all as specified and as directed.

S&F mild steel works in tubular trusses, rafters, purlins, etc. including special shaped washers etc. complete using ERW or induction butt welded tubes conforming to IS.1161-1979 grade St.-240 all as specified and as directed.

S&F mild steel framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc. n exc 10 kg each brackets, Fe-410-W Gde-E-250 quality-A all as specified and as directed. all as specified and as directed.

M&L for mild steel flats as in wind ties for roof including securing bolts and necessary drilling, conforming to Fe-290 Gde E-165 all as specified and as directed.

S&F Mild Steel bolts purpose made not exc. 12mm dia neck and exc 30cm long with hexagonal or square head on one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square all as specified and as directed

M&L for pre-painted galvalume coated high tensile corrugated/ trapezoidal profile steel sheets, AZ-70 coating mass, 550 Mpa yield strength, 0.5mm thick (TCT), as in roofing/ cladding fixed with self drilling fasteners as per manufacturers instructions all as specified and as directed. Note: Measurement shall be taken flat as fixed without any allowance for laps, etc.

M&L for pre-painted galvalume coated high tensile plain profile steel sheets, AZ-70 coating mass, 550 Mpa yield strength, 0.5mm thick (TCT), as in ridges, valleys, hips, claddings, etc. fixed with self drilling fasteners as per manufacturers instructions all as specified and as directed. Note: Measurement shall be taken flat as fixed without any allowance for laps, etc.

M&L for 3mm thick Aluminium Composite Panel comprising of a core containing not less than 70% non combustible mineral filling sandwiched between two skins of 0.5mm thick aluminium alloy PERALUMAN-100 (AlMg1-NS41) complete with all necessary sub-structures, anchors, hardware and fittings to provide a total installation, fixed to existing wooden/ steel members all as per manufacturers instructions, all as specified and as directed. Note: Measurement shall be taken flat as fixed without any allowance for laps, etc. Make: Alstrong/ Aludecor/ Alucobond/ Eurobond

S&F PVC (SWR) eaves gutter half round/ square/ trapezoidal profile 150mm bore including pipe accessories PVC holder bats bolts nuts etc. all as specified and directed.

S&F 4mm thick High Pressure Steam Cured (HPSC) non asbestos fibre cement building board in false ceiling with aluminum anodized snap grids of 60x60cm with Tee section 35x25x1.25mm, angle section 25x25x1.25mm thick including 2mm dia GI hanging wire including all hanger fittings etc including provision three coats of white wash on ceiling all as specified and directed.

S&F 10 to 15mm thick plaster of paris ceiling (Gypsum anhydrous) to flat surface as in false ceiling with aluminum anodized snap grids of size not less than 600mm x 900mm with GI sheets of 1.25mm thick x 75mm wide reinforced with GI chicken wire mesh of aperture 10mm and dia of wire 1mm including provision of 8mm dia suspender bars not more than 1m c/c on either sides including all hanger fittings etc duly tied with roof members including provision two coats of plastic emulsion paint of any colour, over a coat of primer on ceiling all as specified and directed.

M&L for 50mm thick plain cement concrete 1:4:8 type D2 using 40mm graded aggregate as in sub base/ levelling course for flooring all as specified and directed.

M&L for 75mm thick plain cement concrete 1:4:8 type D2 using 40mm graded aggregate as in sub base/ levelling course for flooring all as specified and directed.

M&L for 25mm thick plain cement concrete 1:2:4 type B0 using 12.5mm graded aggregate as in sub base for flooring finished even and fair all as specified and directed.

M&L for 100 mm thick plain cement concrete 1:2:4 type B2 using 40mm graded stone aggregate as in sub base for floor/ paving/ hard standing, etc. all as specified and directed.

M&L for 15mm thick wear proof topping by mixing of cement and metallic floor hardener mixed thoroughly to an even colour in dry state in the proportions recommended by the manufacturer and mixing this mixture with crushed granite stone chips of size 6mm and down in the proportion 1:2 by volume and laying on the sub base while the concrete is green and finishing the concrete surface even and smooth without using extra cement all as specified and directed. Note: Metallic floor hardener shall be measure and paid separately.

Supply only approved metallic floor hardener all as specified.

M&L for 100mm thick plain cement concrete 1:2:4 type B1 using 20mm graded stone aggregate as in paving/ hard standing/ floor laid in alternate bays and finishing the concrete surface even and smooth without using extra cement and making impressions of expanded metal while the concrete is green all as specified and directed.

M&L for coloured vitrified tiles, square or rectangular, light shade, 9 to 10mm thick, area of each tile not exc 0.36 Sqm, as in floors, set and jointed in neat cement slurry and pointed in white cement mixed with colouring pigments to match the shade of the tile laid over and including 15mm thick screed bed in cement mortar 1:4 all as specified and directed.

M&L for coloured non skid ceramic tiles, edge cut, 7 to 8mm thick area of each tile exc 0.11 Sqm but not exc 0.18 Sqm, in floors, etc. set and jointed in neat cement slurry and pointed in white cement mixed with colouring pigments to match the shade of the tile laid over and including 15mm thick screed bed in cement mortar 1:4 all as specified and directed.

M&L for coloured matt finished ceramic tiles, edge cut, 9 to 10mm thick area of each tile exc 0.18 Sqm but not exc 0.38 Sqm, in floors/ skirting, etc. set and jointed in neat cement slurry and pointed in white cement mixed with colouring pigments to match the shade of the tile laid over and including 15mm thick screed bed in cement mortar 1:4 all as specified and directed.

M&L for coloured glazed ceramic tiles 350mm x 450mm x 7 to 8mm thick on vertical surfaces such as skirting, dados etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match with surfaces including 10mm thick backing coat in CM 1:4 all as specified and directed.

M&L for machine cut granite stone slab, premium quality, any colour, 18 to 19mm thick, set and jointed with neat cement slurry laid over and including 15mm thick screed bed in cement mortar 1:6 and pointed in white cement (1:2) mixed with colouring pigments to match with the shade of slab, as in platforms, steps, cills, etc. including rubbing and polishing complete all as specified and directed.

M&L for machine cut granite stone slab, 18 to 19mm thick, as in risers of steps, skirting, dado, cladding to pillars, etc., laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including bull nosing the edges, rubbing and polishing complete including 15mm thick backing coat in CM 1:4 all as specified and directed.

M&L for machine cut Kota stone slab, 20-25mm thick, as in flooring, laid and jointed with neat slurry and pointed with grey cement slurry mixed with pigment to match the shade of the slab including bull nosing the edges, rubbing and polishing complete including 15mm thick screed bed in cement mortar 1:4 all as specified and directed.

M&L for machine cut Kota stone slab, 20-25mm thick, as in risers of steps, skirting, dado, cladding to pillars, etc., laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including bull nosing the edges, rubbing and polishing complete including 10mm thick backing coat in CM 1:4 all as specified and directed.

M&L for chequered cement concrete tiles 30cm x 30cm x 25mm thick, with grey cement and pigments, set jointed and pointed in neat cement slurry, laid over and including 15mm thick screed bed in cement mortar 1:6 as in pathways, etc. complete all as specified and directed.

M&L for 55-60mm thick machine pressed precast concrete interlocking coloured paver blocks, M-35 grade, any shape and size with glossy finish on top, confirming to IS 15658-2006 all as specified and directed.

M&L for crushed stone sand (M-sand/ Robo sand/ I-sand) as in cushioning for interlocking paver blocks including watering and consolidating complete all as specified and as directed.

M&L for plain cement concrete 1:3:6, type C1, using 20 mm graded stone aggregate, 75mm thick as in plinth protection, finishing the surface fair and even, in panels & filling joints with mortar, etc. all as specified and directed.

M&L for rendering 10mm thick in cement mortar 1:6 on fair faces of brick work or PCC block masonry or concrete surfaces finished even and smooth without using extra cement complete all as directed.

M&L for rendering 5mm thick in cement mortar 1:4 mixed with water proofing compound over 10mm thick backing coat in cement mortar 1:6 on fair faces of brick work or PCC block masonry or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed. Note: Water proofing compound shall be measured and paid separately.

M&L for rendering 5mm thick in cement mortar 1:4 mixed with water proofing compound over 10mm thick backing coat in cement mortar 1:6 on stone masonry surfaces or other than fair faces of brick work, finished even and smooth without using extra cement complete all as specified and directed. Note: Water proofing compound shall be measured and paid separately.

M&L for 5mm thick sheet glass ordinary quality and glazing with oil putty/ neoprene beading in square n exc 0.5 sqm in each pane all as specified and directed.

S&F toughened glass with etching design as approved, 10mm to 12mm thick, including provision of necessary PVC rollers of suitable size, as in sliding door shutter all as specified and as directed. Note: Aluminium frame work and handle shall be measured and paid separately.

S&F stainless steel handle, satin finish, 300mm long, suitable for fixing with glass shutter all as specified and as directed.

M&L for three coats of white wash on newly plastered walls, pilasters, cornices, etc. including necessary preparation of surfaces all as specified and directed.

M&L for three coats of white wash on walls, pilasters, cornices, etc. including complete removal existing treatment and necessary preparation of surfaces all as specified and directed.

M&L for two coats of oil bound distemper (Acrylic distemper washable), any colour, over a coat of primer over 1mm thick layer of wall care putty, on newly plastered walls, pilasters, cornices, etc., including necessary preparation of surfaces all as specified and as directed.

M&L for two coats of oil bound distemper (Acrylic distemper washable) over a coat of primer over 1mm thick layer of wall care putty, on walls, pillasters, cornices, etc., including complete removal of existing treatment and necessary preparation of surfaces all as specified and as directed.

M&L for two coats of oil bound distemper (Acrylic distemper washable) over a coat of primer on ceilings including complete removal of existing treatment and necessary preparation of surfaces all as specified and as directed.

M&L for two coats of cement based paint, any colour, on newly plastered surfaces of walls, pilasters, cornices, etc., including necessary preparation of surfaces all as specified and directed.

M&L for two coats of weather proof exterior acrylic emulsion paint over a coat of alkali resistant primer on newly plastered surfaces of walls, pillasters, roof projections, facias, drops, chajjas, etc., including necessary preparation of surfaces all as specified and as directed.

M&L for two coats of weather proof exterior acrylic emulsion paint over a coat of alkali resistant primer on surfaces of walls, pillasters, roof projections, facias, drops, chajjas, etc., including complete removal of existing treatment and necessary preparation of surfaces all as specified and as directed.

M&L for preparing surface of wood and wood based materials, new or old, of any description and girth, not otherwise described and treated with two coats of creosote oil all as specified and directed.

M&L for preparation of old painted wooden surfaces over 10 cm width or girth and applying one coat of synthetic enamel paint all as specified and directed.

M&L for preparation of new wooden surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer all as specified and directed.

M&L for preparation of new steel surfaces over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and directed.

M&L for preparation of new steel surfaces of any description n exc 10 cm width or girth when unconnected with other painting or when painted in a different tint and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and directed.

S&F 15mm bore galvanized iron tubes, medium grade, with all fittings, fixed complete to walls, ceilings or laid in floors all as specified and directed.

S&F 20mm bore galvanized iron tubes, medium grade, with all fittings, fixed complete to walls, ceilings or laid in floors all as specified and directed.

S&F in repairs 15mm bore bib taps, fancy type, brass CP, screwed for iron pipe or for brass ferrule and fixed all as specified and as directed. Make: Cat No. CON 107 KN of JAQUAR or equivalent model in ESS ESS/ JOHNSON/ CERA

S&F in repairs 3 way mixer tap for mixing hot and cold water, fancy type, brass chromium plated screwed down for 15mm bore GI pipe all as specified and directed. Make: CAT No. CON-CHR 273 KNUPR of JAQUAR or equivalent model in JOHNSON/ CERA

S&F in repairs 15mm bore stop valves, fancy type brass CP, with long shank and cup (concealed type), screwed down high pressure, screwed both ends for iron pipe for unions all as specified and as directed. Make: Cat No. CON 053 KN of JAQUAR or equivalent model in ESS ESS/ JOHNSON/ CERA

S&F in repairs fancy type pillar taps brass chromium plated with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed down high pressure screwed for 15mm bore GI pipe all as specified and directed. Make: CAT No. CON 011 KN of JAQUAR or equivalent model in JOHNSON/ CERA

S&F in repairs vitreous china counter type oval wash basin, white, size 550x450mm with vitreous china pedestal, waste pipe and waste fitting including CI brackets and cutting for and pinning in ends of brackets or erecting stands, etc. complete all as specified and directed.

S&F in repairs cascade type vitreous china wash down water closet pan (pedestal pattern), white, coupled with flushing cistern including 'P' or 'S' trap, seat and cover, fixing bolts etc, connecting to drain pipe and flushing pipe all as specified and as directed.

S&F in repairs 15 mm bore 2 way Bib tap, long body, brass chromium plated, fancy type, with crutch or butter-fly handle, screwed down, screwed for iron pipe or for brass ferrule etc all as specified and directed. Make: Cat No. FUS 29041 of JAQUAR or equivalent model in JOHNSON/ CERA

S&F in repairs health faucet, brass chromium plated with 1m long flexible PVC tube and wall hook all as specified and as directed. Make: Cat No. ALD-CHR 563 of JAQUAR or equivalent model in JOHNSON/ CERA

S&F in repairs bass chromium plated toilet paper holder fixed to wall with wooden plugs, chromium plated brass screws and cup washers all as specified and as directed. Make: Cat No. 1151N of JAQUAR or equivalent model in JOHNSON/ ESS ESS/ ARK

S&F in repairs soap dish, vitreous china, white, any type, fixed to wall with CP screws all as specified and as directed.

S&F in repairs liquid soap container, PTMT, minimum weight 105 gms, fixed to wall with CP screws and wooden/ plastic cleats all as specified and as directed.

S&F in repairs fancy type towel rod, brass CP, 600mm long, fixed to wall with plugs and chromium plated screws all as specified and as directed. Make: CAT No. ACN 1111 SM of JAQUAR or equivalent model in JOHNSON/ ESS ESS/ CERA

S&F in repairs brass chromium plated overhead shower set with flange, swivel type, suitable for fixing with 15mm bore GI pipe including CP shower arm, fixed with wall flange all as specified and directed. Make: Cat No. F160039 of HINDWARE or equivalent model in JAQUAR/ JOHNSON

S&F in repairs corner glass shelf, 5mm thick, 9" wide, fixed with suitable mild steel CP brackets, nuts and bolts, all as specified and directed. Make: HINDWARE/ JAQUAR/ JOHNSON

S&F in repairs PVC connection 15mm size with PTMT nuts, 450mm long all as specified and directed.

S&F in repairs 75 mm bore UPVC (SWR) pipes, single socketed, in any length, with solvent cement joints, fixed to wall or laid trenches or in floors, all as specified and directed.

S&F in repairs 110 mm bore UPVC (SWR) pipes, single socketed, in any length, with solvent cement joints, fixed to wall or laid trenches or in floors, all as specified and directed.

S&F in repairs 110mm bore UPVC (SWR) bends any radius all as specified and directed.

S&F in repairs 75mm bore UPVC (SWR) bends any radius all as specified and directed.

S&F in repairs 110mm bore UPVC (SWR) vent cowl all as specified and directed.

S&F in repairs UPVC (SWR) gully trap 125/110mm, setting & jointing with solvent cement all as specified and as directed

S&F UPVC PVC (SWR) floor trap plain with grating including jointing with solvent cement 75mm dia outlet all as specified and directed.

Taking down carefully existing point wiring of light/ fan/ bell/ 5 Amps socket/ 15 Amps socket/ 2 way light point, etc. complete of any description including fittings and fixtures such as switches, sockets, ceiling roses, pendants, holders, regulators, call bells, light fittings, etc. and making good the disturbed surfaces of walls, floors, etc. all as specified and directed.

M&L for Point wiring complete with 1.5 sqmm single core PVC insulated FRLS unsheathed 1100 volt grade copper conductor multi-stranded cables drawn through and including ISI marked PVC conduit/ PVC casing capping of suitable size and all necessary fittings and provision of one run of PVC insulated FRLS unsheathed 1100 volt grade copper conductor multi-stranded single core cable of size 1.5 sqmm and connected to common earth dolly including 1/2 module PVC surface mounting box with standard white modular cover plate & frames for mounting modular type switches/ sockets etc. for one light point controlled by one switch 1 way complete all as specified and directed.

All as described in item No. 130 but for one fan point controlled by one switch and regulator.

All as described in item No. 130 but for one 05 Amps socket outlet on independent board.

All as described in item No. 130 but for one 05 Amps socket outlet on the same board with other switches.

All as described in item No. 130 but wiring with 2.5 Sqmm single core PVC insulated FRLS unsheathed 1100 volt grade multi-stranded copper conductor cable and with one run of single core PVC insulated FRLS unsheathed 1100 volt grade multi-stranded copper conductor cable of size 2.5 Sqmm for earth continuity conductor and connecting to common earth dolly, complete for one 15 Amps power socket point on independent board all as specified and directed.

M&L for sub main wiring with 2 runs of single core PVC insulated FRLS unsheathed multi-stranded copper conductor cables of size 6 sqmm drawn through and 1100 volt grade including PVC casing and capping of suitable size with all necessary fittings and provision of one run of 6 sqmm PVC insulated FRLS unsheathed multistranded copper conductor single core for earth continuity and connected to common earth dolly, including taking down existing unserviceable sub main wiring of any description and making good disturbed surfaces complete all as specified and directed. Note: Two runs of 6 sqmm cable, one run of 6 sqmm earth conductor cable and one run of PVC casing and caping shall be measured and paid together as one unit length.

S&F modular switch, 1 module, 1 way, 6 Amps, 230 volts, AC, all as specified and directed.

S&F modular switch, 1 module, 1 way, 16 Amps 230 volts, AC, all as specified and directed.

S&F modular socket outlet, 2 module, 6 Amps 2 cum 3 pin multipurpose all as specified and directed.

S&F modular socket outlet, 2 module, 2 pin 6A/ 3 pin 16 Amps, multipurpose all as specified and directed.

S&F PVC ceiling rose 3 terminal suitable for 230 volts AC supply all as specified and directed.

S&F fan regulator electronic modular step type, 2 module, suitable for 1200mm sweep ceiling fan all as specified and directed.

S&F Single pole and neutral enclosure, powder coated, with a two pin earth plug and socket complete, 20 Amps, 240V, including provision of one single pole MCB 20 Amps 'C' curve type all as specified and as directed.

S&F in repairs, MCB DB TPN 4 Way with 200 Amps rated bus bars double door type including provision of 2nd class hard wood board with sunmica top of suitable size fixed to wall and fixing of the MCB DB on board complete all as specified and directed.

S&F MCB DB SPN 12 Way with 100 Amps rated bus bars double door type including provision of 2nd class hard wood board with sunmica top of suitable size fixed to wall and fixing of the MCB DB on board complete all as specified and directed.

S&F MCB DB SPN 8 Way with 100 Amps rated bus bars double door type including provision of 2nd class hard wood board with sunmica top of suitable size fixed to wall and fixing of the MCB DB on board complete all as specified and directed.

S&F MCB TPN 63A 'C' series 50Hz AC supply all as specified and as directed.

S&F MCB DP 63A 10KA 'C' series 50Hz AC supply all as specified and as directed.

S&F MCB SP 5-32A 10KA 'C' series 50Hz 240 Volts AC supply all as specified and as directed.

S&F surface mounting LED light fitting, 20W, 230V, wall/ ceiling mounted type, with extruded aluminium housing and polycarbonate diffuser, 20W LED strip, integrated driver and all accessories internally pre wired complete and connecting up light fitting with twin core twisted flexible copper conductor cable of suitable size from ceiling rose to connector block and provision of 2 Nos. of PVC square blocks all as specified and directed. Make: HAVELLS LUMILINE PLUS or equivalent in CG/ Philips/ Wipro

S&F surface mounting LED light fitting, 10W, 230V, wall/ ceiling mounted type, with extruded aluminium housing and polycarbonate diffuser, 10W LED strip, integrated driver and all accessories internally pre wired complete and connecting up light fitting with twin core twisted flexible copper conductor cable of suitable size from ceiling rose to connector block and provision of 2 Nos. of PVC square blocks all as specified and directed. Make: HAVELLS LUMILINE PLUS or equivalent in CG/ Philips/ Wipro

S&F 34 Watts LED glare free luminaire recess mounted in square profile 2ft x 2ft size with 34 W high brightness SMD LEDs including electronic driver etc. complete with all accessories internally pre wired connecting up light fitting with twin core twisted flexible copper conductor cable of suitable size from ceiling rose to connector block all as specified and directed. Make: HAVELLS VENUS NEO HE 2x2 or equivalent in CG/ Philips/ Wipro

S&F in repairs surface mounting LED PANEL light fitting, recess mounted, 9W, 230V, with opal diffuser integrated electronic driver and all accessories internally pre wired complete including provision of 9W high brightness LEDs and connecting up light fitting with twin core twisted flexible copper conductor cable of suitable size from ceiling rose to connector block all as specified and directed. Make: HAVELLS OCTANE PANEL or equivalent in Crompton Greaves/ Philips/ Wipro

S&F 25 Watts LED security light fitting, with pressure die cast aluminium housing and lens embedded PC cover having top opening separate driver compartment with IP66 protection, 25 Watts high power LEDs, electronic driver including all accessories internally pre wired complete and connecting up light fitting with twin core twisted flexible copper conductor cable of suitable size from ceiling rose to connector block including provision of bracket made out of GI pipe light grade of suitable size and length and bent to shape fixed to walls/ poles with suitable MS clamps, bolt, nuts etc. complete all as specified and directed. Make: ENDURA PEARL model of HAVELLS or equivalent in Crompton Greaves/ Philips/ Wipro

S&F wall mounting fan, 230 volts, single phase, 300mm sweep, with all accessories complete including provision of suitable clamps for fixing to wall and making good disturbed surfaces matching with the existing surface complete all as specified and as directed. Make: HAVELLS Model No. D'zire or equivalent model in makes Crompton Greaves/ USHA

S&F ceiling fan, 230 volts, single phase, 1200mm sweep, 3 blades and provision of suitable size GI pipe down rod with all accessories complete including taking down existing unserviceable ceiling fan of any description and size and depositing to MES E/M store all as specified and as directed. Make: HAVELLS Model No. ES-50 or equivalent model in makes CG/ ORIENT

M&L for 50mm dia GI pipe medium grade cut to required length as per site requirement and fixed into walls in single piece without any joints as in supports for hanging of ceiling fans complete all as specified and directed.

S&F in repairs exhaust fan, 250mm sweep, 1200 RPM, 230 Volts, single phase, PVC body with gravity shutter and fixing arrangements including fixed into plywood base of suitable size with suitable bolts and nuts and fixing the plywood to existing window and provision of suitable size flexible copper conductor cable from connector to ceiling rose all as specified as directed. Make: Ventil Air-DX model of HAVELLS or equivalent model in USHA/ KHAITAN/ CROMPTON GREAVES

S&F in repairs storage type water heater (Geyser), 25 litres capacity, 2 KW, vertical type including drilling holes into wall, provision of 4 Nos of suitable size anchor bolts, nuts and washers, 2 Nos. of PVC connections 450mm long, Non return valve connecting up electrical & water supply lines, testing and making good disturbed surfaces complete all as specified and as directed. Make: MONZA DX Model of HAVELLS or equivalent model in RACOLD/ USHA/ CROMPTON GREAVES

M&L for XLPE insulated, armoured, heavy duty electric LT UG cable with multi-stranded aluminium conductor, 1100 Volts grade, cross sectional area 25 Sqmm x 4 core, laid in trenches/ passing through pipe/ duct or fixed to wall including provision of necessary lugs/ thimbles/ ferrules, connecting up , testing and commissioning complete laid in repairs all as specified and as directed. Note: Excavation, earth work, cable cushioning, bricks/ GI pipe for protection shall be measured and paid separately under relevant items of this schedule.

M&L for double wall corrugated HDPE pipes, conforming to IS 14930-2001, ISI marked, 63mm outer dia, as in cable protection, fixed to poles/ walls with necessary MS clamps, bolts, nuts, washers or laid in trenches/ under roads/ crossing etc. all as specified and as directed.

M&L for GI tubes, light grade, 40mm bore, as in cable protection, fixed to poles/ walls with necessary MS clamps, bolts, nuts, washers or laid in trenches / under roads/ crossing etc. all as specified and as directed.

Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6mm thick, burried directly in ground vertically (earth pit not less than 2.25 metre deep below normal ground level) with top edge of the earth plate at a depth not less than 1.5m below normal ground level connected to GI wire 4mm dia (7.5m long) by means of GI bolts nuts washers and GI wire protected by 15mm dia light grade GI pipe (7.5m long) and watering arrangements with 20mm dia GI pipe medium grade and GI funnel all as specified and shown in Electrical Plate No 3 of MES Schedule Part I including necessary excavation and earth work in any type of soil, charcoal, dust salt, PCC 1:2:4 type B1 in chamber, 40mm thick RCC 1:2:4 type B1 in cover slab with 8mm dia TMT bars at 100mm C/C both ways and with 8mm dia MS hook complete and testing all as specified and directed.

M/s. N D KALING

M/s. KIRAN M CHOUGULE

ASHOK M RAJGOLKAR

M/s. VIJAY ELECTRICALS

M/s B C CHOUGULE

SAMARTH ASSOCIATES