REPAIR REPLACEMENT OF INTERNAL WIRING REPAIR OF GYSER CELING FAN EXHAUST FAN REPAIR TO SOLAR WATER HEATER LIGHITING CONDUCTOR EARTHING AND OTHER MISC REPAIR WORK AT OTM ACCN UNDER AGE EM FOR AGE B R I REGION UNDER GE N AT MIL STATION BIKANER

Amount

Taking down switch boards / fitting / fixture , identify and rectify the complaints pertains to internal electrification of any type and nature of MD Accns such as rectification of faulty electric circuit , tightening of loose wiring / conduits replacement of defective accessories such as switch, socket, ceiling rose , holders etc. shall be measured and paid separately. Cost of minor stores , such as screws, clamps, washers,bakelite laminated sheet top cover, insulation tapes, nut , bolts etc. shall be deemed including in the quoted rate complete all as specified and as directed by Engr-in-Charge . ( Note . If the contractor fail to rectify the defects mentioned in the complaint slip on within 48 hrs,. he will be charged Rs. 100/- per complaints/ per day and same will be recovered from his RAR . Each job shall contain 10 complaints). The contractor / his rep will collect the complaint from complaint cell ( Concerned JE E/M) every day at 9.00 AM and rectify the complaints 48 hrs and deposit the complaint slip ( duly signed by the users ) to concerned JE E/M.

Taking down carefully (aluminium) point wiring complete of any type (batten/ surface conduit or concealed) for light point, fan point, bell point socket point or power point complete with all fitting such as switches, sockets pendants, ceiling rose, round block etc complete and making good disturbed surfaces of wall, floor or ceiling with plaster of tiles or roof treatment etc and finishing the surfaces with distemper/white washing/colour washing to match with the existing surface complete all as specified and as directed by Engr-in-Charge .

M & L for point wiring with and including single core FRLSH PVC insulated and unsheathed stranded copper conductor cable of size 1.5 sqmm 1100 volts grade drawn through and including suitable size of PVC cassing cappingt with accessories with laminated top cover fixed on MS sunken box for housing of switch, socket, regulator etc complete with and including 1.5 sqmm FRLSH PVC insulated and unsheathed stranded copper conductor cable as earth wire and connected to common earth dolly and making good to the disturbed surfaces of wall, floor, ceiling etc to match with exisiting surface complete all as specified and as directed by Engr-in-Charge .

All as per item No 3 here-in-before but socket point 5 Amps on independent board complete as specifed as directed by Engineer - In - Charge

All as per item No 3 here-in-before but socket point 5 Amps on the same board with other switches complete as specifed as directed by Engineer - In - Charge

All as per item No 3 here-in-before but cable of 4 Sq mm for 15 Amp switch socket outlet on independent board including provision of 4 Sqmm PVC insulatred unshethed multistranded copper conductor as earth wire

All as per item No 3 here-in-before but for one light point control by two way switch complete all as specified and as directed by Engineer-in-Charge.

M & L for point wiring with and including single core FRLSH PVC insulated and unsheathed stranded copper conductor cable of size 1.5 sqmm 1100 volts grade drawn through and including suitable size of PVC concealed conduit with accessories with laminated top cover fixed on MS sunken box for housing of switch, socket, regulator etc complete with and including 1.5 sqmm FRLSH PVC insulated and unsheathed stranded copper conductor cable as earth wire and connected to common earth dolly and making good to the disturbed surfaces of wall, floor, ceiling etc to match with exisiting surface complete all as specified and as directed by Engr-in-Charge for the following :- (a) One Light/fan/ex-fan/Bell/point controlled by one switch.

(b)One pin 5 amps socket point on the same board with other switches complete

(c) One 3 pin 5 amps socket on independent board.

All as per item No 8 above but with 4.0 sqmm copper wire for 3 pin socket outlet 15/20 Amp on independent board complete and all as directed by Engr-in-charge.

M & L for point wiring with and including single core FRLSH PVC insulated and unsheathed stranded copper conductor cable of size 1.5 sqmm 1100 volts grade drawn through in existing conduit with accessories with laminated top cover fixed on MS sunken box for housing of switch, socket, regulator etc complete with and including 1.5 sqmm FRLSH PVC insulated and unsheathed stranded copper conductor cable as earth wire and connected to common earth dolly and making good to the disturbed surfaces of wall, floor, ceiling etc to match with exisiting surface complete all as specified and as directed by Engr-in-Charge for the following :- (a) One Light/fan/ex-fan/Bell/point controlled by one switch.

(b)One pin 5 amps socket point on the same board with other switches complete

(c) One 3 pin 5 amps socket on independent board.

all as per item No-10 above but with 4.0 sqmm copper wire for 3 pin socket outlet 15 /20 Amp on independent board complete and all as directed by Engr-in-charge.

Supply & fixing LED T8 Tube light rod ( Retro Fit ) ingress protection IP20 18W in make CG/Havells/Phillips/polycab with complete all as specified and directed by engineer-in-charge.

Supply & fixing Connecting fixture for T8 tube light 1*18w/20w 4 Ft in make CG / Havells/Phillips/ploycab. complete all as specified and directed by engineer-in-charge.

S&F LED tube light fitting, 1x 20-22 watts, 230 volt, basic all purpose surface and wall mounted led batten with polycarbonate housing & integrated electronic driver, pre-wired and fixed on walls with all fixing accessories such as screws, clips etc and connecting up with two core flexible copper conductor cable of size 24/0.20 sqmm complete all as specified and directed by Engr-in-charge. Make : Philips-BN021 LED 20S PSU CW GR S2/ Crompton Greaves LDDR20-CDL Dazzle Ray / bajaj-BCLAB 20W

Supply and fixing LED mirror light fitting , type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size (a) One Light/fan/ex-fan/Bell/point controlled by one switch. HAVELLS CAT PART NO-ENDURALINEARNEOBS10WLED865SPCWH/WIPRO CAT PART NO-LL20-111-XXX-65NE3/BCLSB 10 WH

S & F LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size. complete all as specified and directed by engineer-in-charge.

S&F in replacement angular holder Poly carbonate body with back plate complete all as specified and as directed by Engineer-in-Charge.Make - Havells. Cona, SSK, wipro, Legrand

S&F in replacement Switch piano Single pole 5 Amps, two way, complete all as specified and as directed by Engineer-in-Charge. Make - Havells. Cona, SSK, wipro, Legrand

S&F in replacement switch piano flush type, Single pole 5 Amps, one way, complete all as specified and as directed by Engineer-in-Charge Make - Havells. Cona, SSK, wipro, Legrand

S&F in replacement of switch piano flush type, Single pole 15 Amps, one way, complete all as specified and as directed by Engineer-in-Charge Make - Havells. Cona, SSK, wipro, Legrand

S&F in replacement of socket outlet flush type, 3/5 pin, 5/15 Amps, complete all as specified and as directed by Engineer-in-Charge. Make - Havells. Cona, SSK, wipro, Legrand

S&F in repalcement of Switch Socket combination flush type 15Amps, complete all as specified and as directed by Engineer-in-Charge. Make - Havells. Cona, SSK, wipro, Legrand

S&F in replacement of socket outlet flush type, 3 pin, 5 Amps, complete all as specified and as directed by Engineer-in-Charge. Make - Havells. Cona, SSK, wipro, Legrand

S&F in replacement of ceiling fan regulator electronic type, 230 Volt, 150 Watt with 5 step of control including making holes in laminated bakelite sheet cover and connection complete all as specified and as directed by Engineer-in-Charge.

S&F in replacement of ceiling rose poly carbonate insulated body three terminal ISI marked, complete all as specified and as directed by Engineer-in-Charge

S&F in replacment PLS Lamp two pin 9/10/11W Make :Crompton Greaves/Philips/Wipro

S&F in replacment PLS Lamp two pin 18W complete all as specified and directed by engineer-in-charge. Make :Crompton Greaves/Philips/Wipro

S&F in replacement Recessed mounting LED 2x2 luminaire type BCTBLR 36W ZTN NW in make Bajaj or equivelent in CG / Phillips / GE / Wipro / Havell's

Supply and Fixing in replacement MCB single pole, 240 volts of rating 6-32 Amps of C curve breaking capacity of 10 KA complete all as specified and as directed by Engineer-in-Charge Make :- Legrand,ABB,Schneider

Supply and Fixing in replacement MCB suitable for 6 to 32 Amps, 240 Volt AC supply C Curve single pole and neutral(SPN) with over load and short circuit protection having rupturing capacity not less than 10 KA complete all as specified and as directed by Engineer-in-Charge. Make :- ABB,Legrand,Schneider

Supply and Fixing only MCB 63 Amps, 440 Volt AC supply Triple pole with neutral(TPN) C curve with over load and short circuit protection having rupturing capacity not less than 10 KA complete all as specified and as directed by Engineer-in-Charge. Make :- Legrand/ABB/Schneider

S&F sheet metal enclosure MCCB DB, double door, 415 Volt ,vertical TPN 4 way with 200 Amps rated busbarcomplete all as specified and directed by engineer-in-charge. Make:- Hegar/Legrand/Seimens

S&F MCCB 63 amps, 4 pole, 415 volts, fixed type breaking capacity 16KA complete all as specified and as directed by Engr-in-charge.

S&F MCCB 100amps, C curve TPN, 415 volts,16KA,4 Pole complete all as specified and as directed by Engr-in-charge.

S&F MCCB 125amps, C curve TPN, 415 volts, 16KA, 4 Pole complete all as specified and as directed by Engr-in-charge.

S&F blank cover for MCB DBs complete all as specified and directed by engineer-in-charge.

S&F in replacement Bell Ding dong AC single pole 230volts Make : Havells,Cona,SSK,wipro, Legrand

S&F in replacement Bell push button Piano flush type single pole 5Amps complete all as specified and directed by engineer-in-charge. make : Havells,Cona,SSK,wip Legrand

S&F in replacement sub main wiring in PVC casing and capping with 2 single core 10 sqmm multi-stranded PVC insulated cable unsheathed 1100 volts grade with one earth wire of 10 sqmm copper conductor cable connected to common earth and earth dolly complete and including PVC Cassing and Capping all as specified and as directed by Engineer-in-Charge.(Note two run of 10 sqmm and one run of 10 sqmm will be measured as 1 RM.Make of cables: Nicco, L&T, Paragon, havells

All as per item No 43 above but of size 6 sqmm and earth wire of 6 sqmm

All as per item No 43 above but of size 4 sqmm and earth wire of 4 sqmm

M&L for submain wiring using 4 runs of single core FRLS PVC insulated, unsheathed stranded copper conductor cable of size 4runs of 10 Sqmm of voltage rating 1100V for three phase & neutral, drawn in and including concealed PVC conduit of dia not less than 25 mm dia with standard acessories, along with two run of FRLS PVC insulated, unsheathed, stranded copper conductor of size 2x 6.0 Sqmm as earth continuity conductor all as specified and directed(Note-4 runs of single core FRLS PVC cable 10sqmm for three phase & neutral with Two run of earth conductor as earth and conduit shall be measured as one unit)complete all as specified and directed by engineer-in-charge.

M&L for submain wiring using 4 runs of single core FRLS PVC insulated, unsheathed stranded copper conductor cable of size 4runs of 6 Sqmm of voltage rating 1100V for three phase & neutral, drawn in and including concealed PVC conduit of dia not less than 25 mm dia with standard acessories, along with two run of FRLS PVC insulated, unsheathed, stranded copper conductor of size 2x 4.0 Sqmm as earth continuity conductor all as specified and directed(Note-4 runs of single core FRLS PVC cable 6sqmm for three phase & neutral with Two run of earth conductor as earth and conduit shall be measured as one unit) complete all as specified and directed by engineer-in-charge.

S&F in replacement Sheet metal enclosure for distribution boards flushed in wall Double door suitable for fixing MCBs 240 volts with 200 Amps rated bus bar,SPN 8 ways, including taking down of old unsv DB,s and making good the disturbed surface of wall, complete all as specified and as directed by Engineer-in-Charge. Make -L&T ( Exora series)/Schneider/ legrand/Schnedier/GE /English Elect Note : cost of cutting/chasing of wall and making good disturbed surface deemed to be included in the rate

S&F in replacement Sheet metal enclosure for distribution boards flushed in wall Double door suitable for fixing MCBs 240 volts with 200 Amps rated bus bar,SPN 12 ways, including taking down of old unsv DB,s and making good the disturbed surface of wall, complete all as specified and as directed by Engineer-in-Charge. Make -L&T ( Exora series)/Schneider/ legrand/Schnedier/GE /English Elect Note : cost of cutting/chasing of wall and making good disturbed surface deemed to be included in the rate

S&F in replacement Sheet metal enclosure for distribution boards flushed in wall Double door suitable for fixing MCBs 240 volts with 200 Amps rated bus bar,SPN 4 ways, including taking down of old unsv DB,s and making good the disturbed surface of wall, complete all as specified and as directed by Engineer-in-Charge. Make -L&T ( Exora series)/Schneider/ legrand/Schnedier/GE /English Elect Note : cost of cutting/chasing of wall and making good disturbed surface deemed to be included in the rate

S&F in replacement Sheet metal enclosure for distribution boards flushed in wall Double door suitable for fixing MCBs 415volts with 200 Amps rated bus bar,TPN 4 ways, including taking down of old unsv DB,s and making good the disturbed surface of wall, complete all as specified and as directed by Engineer-in-Charge. Make - Legrand / Schneider/ L&T Exora series/GE/English Elect Note : cost of cutting/chasing of wall and making good disturbed surface deemed to be included in the rate

S&F in replacement single pole and neutral enclosure with two pin and earth plug and socket including 1Nos MCB 20Amps capacity complete all as specified and directed by Engr-in-charge Cat Part No 607841 in Make Legrand or equivalent in schneider/Seimens/L&T

S & F in replacement LED Bulb 0.5W (in different colors) complete all as specified and as directed by engr-in-charge.

S&F in replacement bad side fitting with suitable LED bulb complete all as specified and directed by Engr-in-charge. Sample approved by Engr-in-charge and GE .

S&F in replacement Decorative wall light fixture made up of Polycarbonate, suitable for retrofit 9/11 W LED lamp Complete all as specified and directed by Engr-in-charge. Make : Surya / Havell's/ Phillips

Dismantling and taking out faulty wiring including casing and capings/conduits etc and refixing the same after rectification of fault in original position including replacment of copper/aluminum cable any size not more than 10 mtr casing/capping/conduit not more than 5 mtr and testing after completion complete all as specified and directed by engineer-in-charge.

S&F switch Modular type, 6 Amp, 1 module single pole one way, 230 Volts, Modular type complete all as specified and as directed by Engr- in -charge.

S&F switch Modular type, 16 Amp, 1 module single pole one way, 230 Volts, Modular type complete all as specified and as directed by Engr- in -charge.

M&L socket outlet 3 Pin 6 Amps modular type, 2/3 pin combined 2 module 230 Volts complete all as specified and directed by Engr-in-Charge.

M&L socket outlet 3 Pin 6/16 Amps modular type, 2/3 pin combined 2 module 230 Volts complete all as specified and directed by Engr-in-Charge.

supply and fixing fan step regulator modular type,120W -2 module electronic socket type five step controlled 230V AC 50 Hz for complete all as specified and directed by Engr-In-Charge.

S&F IN repair modular white cover plate with frame but 1 module complete all as specified and directed by engineer-in-charge.

S&F IN repair modular white cover plate with frame but 2 module complete all as specified and directed by engineer-in-charge.

S&F IN repair modular white cover plate with frame but 3 module complete all as specified and directed by engineer-in-charge.

S&F IN repair modular white cover plate with frame but 4 modulecomplete all as specified and directed by engineer-in-charge.

S&F IN repair modular white cover plate with frame but 6 module complete all as specified and directed by engineer-in-charge.

S&F IN repair modular white cover plate with frame but 8 module complete all as specified and directed by engineer-in-charge.

S&F IN repair modular metel flush box but 1,2,3 module to suit as existing make complete all as specified and directed by engineer-in-charge.

S&F IN repair modular metel flush box but 4 module to suit as existing make complete all as specified and directed by engineer-in-charge.

S&F IN repair modular metel flush box but 5 module to suit as existing make complete all as specified and directed by engineer-in-charge.

S&F IN repair modular metel flush box but 6,8 module to suit as existing make complete all as specified and directed by engineer-in-charge.

S&F IN repair metel flush sunken box but any size to suit as existing make complete all as specified and directed by engineer-in-charge.

S&F IN repair 3mm thick bakelite laminated sheet top cover with copper screw any size to suit as existing make complete all as specified and directed by engineer-in-charge.

Supply and fixing in replacement of singal core 1.5 sqmm size cable (nominal area) PVC FRLSH multistanded copper conductor cable 1100 volts isi marked draw throw existing point wiring complete all as specified and directed by engineer-in-charge.

Supply and fixing in replacement of singal core 2.5 sqmm size cable (nominal area) PVC FRLSH multistanded copper conductor cable 1100 volts isi marked draw throw existing point wiring complete all as specified and directed by engineer-in-charge.

Supply and fixing in replacement of singal core 4 sqmm size cable (nominal area) PVC FRLSH multistanded copper conductor cable 1100 volts isi marked draw throw existing point wiring complete all as specified and directed by engineer-in-charge.

Supply and fixing in replacement of singal core 6 sqmm size cable (nominal area) PVC FRLSH multistanded copper conductor cable 1100 volts isi marked draw throw existing point wiring complete all as specified and directed by engineer-in-charge.

Taking down submain wiring Aluminium/ copper of any size including earth continuity condutor on teak wood or conduit and removing from site and making good the disturbed surface of wall complete all as specified and directed by engineer-in-charge.

REPAIR TO FAN :- Taking down ceiling fan for repair/serviceing (i.e. winding/ greasing/oiling etc.), 1200/1400 mm sweep of any make and any type model, sealing cable end with tape, dismantling the blades , removing fan and deposite the blades/motor to store for repairing/serviceing complete all as specefied and as directed by Engineer in charge.

Hanging only ceiling fan and connection up the point including provision of cable from ceiling rose to fan complete all as specefied and as directed by Engineer in charge. (Note: For the purpose of payment, the wire using ceiling rose to fan for connection shall be measured and paid seperate in appropriate item and nothing extra pay for this item) complete all as specified and directed by engineer-in-charge.

Re-winding of ceiling fan of size 1200 mm sweep with super enameled copper winding wire of gauge as per existing size /No. of turns confirming to IS, including varnishing the motor windings with best quality varnish complete all as specefied and as directed by Engineer in charge. (Make:Milan/Atlas/Chetak)

Re-winding of ceiling fan of size 1400 mm sweep with super enameled copper winding wire of gauge as per existing size /No. of turns confirming to IS, including varnishing the motor windings with best quality varnish complete all as specefied and as directed by Engineer in charge. (Make:Milan/Atlas/Chetak)

S&F in replacement of ball bearing of size/No. 6201 confirming to IS complete all as specefied and as directed by Engineer in charge.(Make: NBC/SKF)

S&F in replacement of ball bearing of size/No. 6202 confirming to IS complete all as specefied and as directed by Engineer in charge.(Make: NBC/SKF)

S&F in replacement of ball bearing of size/No. 6203 confirming to IS complete all as specefied and as directed by Engineer in charge.(Make: NBC/SKF)

S&F in replacement of brass bush suitable for ceiling fan of any make and model confirming to IS complete all as specefied and as directed by Engineer in charge.

S&F in replacement of shaft for ceiling fan as per existing size and shape complete all as specefied and as directed by Engineer in charge.

S&F fabricated down rod made out of 15mm dia MS Pipe medium Duty 60 cm long duly painted including nut, bolt & washer etc and including drilling holles on top and bottom fan fixing with fan hooks and ceiling fan respectively as reuired suitable for 1200/1400mm sweep of ceiling fan complete all as specified and directed by Engineer-in-charge .

S&F in replacement D Clamp with nuts, bolts, quarter pin and rubber reel suitable for 1200/1400 mm sweep of ceiling fan all as required at site complete all as specefied and as directed by Engineer in charge.

S&F condenser 2.5 MFD confirming to IS complete all as specefied and as directed by Engineer in charge.

S&F of flexible wire of size 23/0.0076 stranded copper conductor complete all as specefied and as directed by Engineer in charge.

S&F in replacement of broken bottom cover (bowl) of PVC suitable for ceiling fan of any make and model as per existing size and shape complete all as specefied and as directed by Engineer in charge.

S&F PVC Canopies (Set of two) as required at site and complete all as specefied and as directed by Engineer in charge

M & L in replacement fan blade (set of three) set suitable for 1200mm sweep ceiling fan of any make complete all as specefied and as directed by Engineer in charge.

M & L in replacement fan blade (set of three) set suitable for 1400mm sweep ceiling fan of any make complete all as specefied and as directed by Engineer in charge.

Cleaning and preparation of old surface of the ceiling fan complete of size 1200/1400mm sweep and spray coat painting with synthetic enameled paint complete all as specified as directed by Engineer-in-Charge.

REPAIR TO EXHAUST FAN Taking down and dismantling of exhaust fan 225mm/300mm/375mm/450mm sweep of any make and model, opening the cover, separating the rotor and stator assembly, locating the fault and making the fan fully serviceable condition including replacing the defected worn out screw, flexible wire of size 23/0.0076 , oiling/greasing the fan and re-assembling the same and testing complete to the satisfaction of Engineer in charge.

Fixing only Exhaust fan and connection up the point including provision of cable from ceiling rose to fan complete all as specefied and as directed by Engineer in charge. (Note: For the purpose of payment, the wire using ceiling rose to fan for connection shall be measured and paid seperate in approprite item of this Schedule) complete all as specified and directed by engineer-in-charge.

Re-winding of exhaust fan 225mm sweep with super enameled copper winding wire as per existing size confirming to IS including varnishing the motor windings with best quality varnish complete all as specefied and as directed by Engineer in charge. (Make:Milan/Atlas/Chetak)

Ditto all as per item No 99 here in above but of size 300mm sweep complete all as specefied and as directed by Engineer in charge.

Ditto all as per item No 99 here in above but of size 375mm sweep complete all as specefied and as directed by Engineer in charge.

Ditto all as per item No 99 here in above but of size 450mm sweep complete all as specefied and as directed by Engineer in charge.

S&F in replacement of blades for size of exhaust fan 225mm dully approved by GE complete all as specefied and as directed by Engineer in charge.

Ditto all as per item No 103 here in above but size of exhuast fan 300mm sweep complete all as specefied and as directed by Engineer in charge.

Ditto all as per item No 103 here in above but size of exhuast fan 375mm sweep complete all as specefied and as directed by Engineer in charge.

Ditto all as per item No 103 here in above but size of exhuast fan 450mm sweep complete all as specefied and as directed by Engineer in charge.

S & F in replacement of condenser 04 MFD confirming to IS complete all as specefied and as directed by Engineer in charge.

S & F in replacement of MS shaft for exhaust fan as per existing size and shape complete all as specefied and as directed by Engineer in charge.

S&F in replacement of MS back side cover for Exhaust fan of any sweep, size and make complete all as specefied and as directed by Engineer in charge.

S&F in replacement exhuast fan louver shutters of size( 225/300/375/450 mm ) and make complete all as specified and as directed by engineer-in-charge.

Cleaning and preparation of old surface of the Exhuast fan complete of size ( 225/300/375/450mm) and Spray painting with synthetic enameled paint complete all as specified as directed by Engineer-in-Charge. Make of paint : Asian/berger/nerolac.

Supply and Fixing PVC Fresh air circulated fan with louver shutters(Exhaust Fan ) of size 225/300 mm

REPAIR TO GEYSER Taking down and opening of the geysers 25/35/50 ltrs capacity any make complete for inspection descaling by chemical treatment of internal parts such as steel inner tank, siphon assembly, heating element, etc re-assembling and refixing the same to its original position after testing on pressure complete all as directed by the Engineer-in-charge. Note :- Items such as glass wool, steel inner tank, siphon assembly etc if found unserviceable under above item will be measured and paid for separately under its relevant item complete all as specified and directed by engineer-in-charge.

Supply and fixing in replacement steel inner tank for capacity of geyser 25 ltrs as per existing size and shape complete all as specified and directed by engineer-in-charge.

Supply and fixing in replacement glass lined inner tank for capacity of geyser 25 ltrs as per existing size and shape complete all as specified and directed by engineer-in-charge. Make : Bajaj/Marc or equivalent

Supply and fixing in replacement siphon assembly suitable for 25 ltrs Geysers, with rubber washer of suitable size.Make : Marc/Bajaj/Polar or equivalent

Supply and fixing in replacement glass wool insulation material complete all as specified and directed by engineer-in-charge.

S&F in repair hot water pipe 15 mm bore 60 cm long with brass unions one(Chromium plated) one on each side. Pipe shall be as per I.S for 15 mm bore of pipe for 25/35/ 50 ltrs capacity Geysers complete all as specified and directed by engineer-in-charge.

Supply and fixing in replacement steel inner tank for capacity of geyser 35/50 ltrs as per existing size and shape complete all as specified and directed by engineer-in-charge.

Supply and fixing in replacement siphon assembly suitable for 35/50 ltrs Geysers, with rubber washer of suitable size complete all as specified and directed by engineer-in-charge.

S&F in repair Thermostat switch I.S.I marked, to Geysers 25/35/50 ltrs of any make / size and shape as per site requirement complete all as specified and directed by engineer-in-charge.

S&F Low density polythene pipe (LDPE) connection arrangement with pipe of pressure rating 2.5 kgf/cm2 , 15 mm bore 30 cm to 45 cm long with brass unions one(Chromium plated) one on each side in repair to Geysers 25/50 ltrs. Pipe shall be as per I.S.I complete all as specified and directed by engineer-in-charge.

Supply and fix in replacement heating element of rating 1.5 KW capacity including washers for 25/35 ltrs capacity Geysers.complete all as specified and directed by engineer-in-charge. Make :- “Marc/THETA/ ALERT”

Supply and fix in replacement heating element of rating 2.0 KW capacity including washers for 50 ltrs capacity Geysers complete all as specified and directed by engineer-in-charge. .Make :- “Marc/THETA/ ALERT”

Supply and fix in replacement Indicator lamps as per existing type having red or green coloured reflector all as specified and directed by Engineer-in-Charge

Supply and fixing in replacement flexible, 3 core PVC insulated copper conductor cable of size 40/0.0076 with over all PVC insulation ISI marked complete all as specified and directed by engineer-in-charge.

Supply and fixing in replacement plug top, 3 pin 15 Amps, including making necessary connections complete all as specified and directed by engineer-in-charge.

Supply and fixing in replacement pressure release valve suitable for 15 mm bore of pipe for 25/ 35/50 ltrs capacity Geysers complete all as specified and directed by engineer-in-charge.

Supply & fixing in replacement bib cock cast copper alloy screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed by engineer-in-charge.

Supply and fixing in replacement stop cock cast copper alloy screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed by engineer-in-charge.

Lagging to pipes used in hot water supply or plumbing all around with 25mm thick, bounded mineral wool performed 'SNAP ON' pipe sections of density 144 Kg/Cum confirming to IS 9842 on outer side of hot water pipe line of 20mm bore including bend with 0.1 mm aluminium foil complete all as specified and directed by engineer-in-charge.

Lagging to pipes used in hot water supply or plumbing all around with 25mm thick, bounded mineral wool performed 'SNAP ON' pipe sections of density 144 Kg/Cum confirming to IS 9842 on outer side of hot water pipe line of 15mm bore including bend with 0.1 mm aluminium complete all as specified and directed by engineer-in-charge.

Lagging to pipes used in hot water supply or plumbing all around with 25mm thick, bounded mineral wool performed 'SNAP ON' pipe sections of density 144 Kg/Cum confirming to IS 9842 on outer side of hot water pipe line of 25mm bore including bend with 0.1 mm aluminium complete all as specified and directed by engineer-in-charge.

Supply & filling distilled water inside solar water storage tank as heat exchanger agent and solar water battery complete all as specified and directed by engineer-in-charge.

S & F in replacement borosilicate glass tube for solar water heater 3.3 with high impact resistance to hail strom evacuated tube of length (1600mm,1800mm,2100mm) , out tube dia 47mm to 58mm , inner tube dia 37mm to 47mm and glass thickness 1.6 ± 0.15 and weight 1.3 Kg to 1.8 Kg single tube complete as per site requirment and sample approved by Eng-In-Charge and GE also. Note :- Glass tube shall be approved by Engineer-In-Charge and as per site requirement contractor shall provide the size of glass tube.

Removing of broken / cracked unserviceable solar flat plate collector cover plate made of toughened glass,including supply and fixing new solar flat plate collector cover plate made of toughened glass of size 3.2mm to 4.06 mm thick of suitable make for existing solar water heating system of capacity any capacity as per site requiment and sample approved by Enginer-in-charge and GE also .

S&F Tubes in replacement, `medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors of pipe 15mm bore complete all as specified and directed by engineer-in-charge.

All as per item No 137 but 20mm bore pipe

All as per item No 137 but 25mm bore pipe

S&F in replacement stop valve, cast copper alloy, screwed down high pressure with crutch or butter fly handle screwed both ends for 20mm bore GI pipe or for unions complete all as specified and directed by engineer-in-charge.

All as per item no. 140 but in size 25mm.

S&F in replacement Rotational moulded polyethylene water storage tanks of 1000 Litres capacity triple layers ISI marked , (cylindrical vertical tanks with closed top) hoisted and fixed in position including making necessary arrangements for fixing inlet, outlet and over flow pipe and provision of wash out pipe etc complete all as specified and as directed by Engr-in-Charge.

All as per item No. 142 here in before but 500 litre capacity.

S&F in replacement Ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe 20 mm dia (minimum weight 210 gms) complete all as specified and as directed by EIC.

M & L in replacement heating element of rating 3.0 KW suitable for solar water heater complete all as specified and directed by engineer-in-charge. make : Theta/Alert.

S & F in replacement metal clad two pin and earth plug top complete all as specified and directed by engineer-in-charge. make : legrand/indo asian/ L&T / standard

Dismantling and cleaning of solar panel by removing all the bird disposal, dust and other migrated disposal deposited on panel both inside and outside with suitable detergent including renewal of all the nut bolts, screw, union complete all as specified and directed by engineer-in-charge.

Removing of unserviceable stainless steel insulated hot water storage tank and supply and fixing new stainless steel insulated hot water storage tank duly fitted with heat exchanger suitable make and size for existing solar heater system of capacity 500 LPD.

Removing of unserviceable stainless steel insulated hot water storage tank and supply and fixing new stainless steel insulated hot water storage tank duly fitted with heat exchanger suitable make and size for existing solar heater system of capacity 300 LPD.

Removing of unserviceable stainless steel insulated hot water storage tank and supply and fixing new stainless steel insulated hot water storage tank duly fitted with heat exchanger suitable make and size for existing solar heater system of capacity 200 LPD.

Removing of unserviceable stainless steel insulated hot water storage tank and supply and fixing new stainless steel insulated hot water storage tank duly fitted with heat exchanger suitable make and size for existing solar heater system of capacity 100 LPD.

S & F in repair bib tap PVC high density of 15mm dia complete all as specified and directed by engineer-in-charge.

Replacement of PVC hose connection heavy duty 20mm dia both ended fitted with union and check nut complete all as specified and directed by engineer-in-charge.

M&L Earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtr below normal ground level surrounded from all sides by 15 cm thick packed layer of charcoal dust and common salt filling in alternate layers and electrode connections by mean of GI wire 4 mm dia by means of bolts, nuts check nuts and washers of GI or steel and connecting to main switch board, testing on completion including GI pipe 20 mm dia light grade for watering and bringing the same upto 30 cm above normal ground level with plug at top including pipe fittings etc complete and GI pipe 15 mm dia light grade for the protection of GI wire from earth pit to earth point complete including necessary excavation and earth work in any type of soil, returning, filling in approved soil and disposal of surplus soil to a distance n.exc 50 m all as specified as shown in electrical plate No 3 SSR Part-I. complete all as specified and directed by engineer-in-charge.

Supply and fixing in replacement outdoor Driver unit 25 watt with surge protection complete all as specified and directed by engineer-in-charge. Make –CG Model SODVES-36-600-25W

Supply and fixing in replacement outdoor Driver unit 45 watt with surge protection complete all as specified and directed by engineer-in-charge. Make –CG Model SODQL-65-700-45W

Supply and fixing in replacement surge protection devices 5 KV compatible with industrial and outdoor LED fixtures upto rated power of 45 Watt complete all as specified and directed by engineer-in-charge. Make CG Model SRPS-5K-440

S&F inreplacement CFL 36watt 04 PL suitable for street light fitting ‘L’ type.Cat Pt Nos 36W CFL 4P 6500K/2700K/4000K in CG or equvalent to Bajaj/Philips

Supply and fixing in replacement choke/ballast electronic 36/40 watt 230 volt for tube light /CFL fitting. Make – Cat Pt Nos EBN136-A/Sin CG or equvalent to Bajaj / Philips

Supply and fixing in replacement Bipin holder for tube light / CFL fittings complete all as specified and directed by engineer-in-charge. Make – Bajaj/Philips/Crompton

Supply and fixing Street light bracket in replacement, made of GI pipe 40mm bore, light grade not less than 1.2 m long bent to shape including fixing with 2 nos suitable size of MS flat iron clamps, nuts, bolts and washers and making connections all as directed by the Engineer-in-Charge.Make of GI pipe : Jindal/Surya/Prakash

Supply and fixing LED street light 25 watts made up of pressure die cast housing with toughned glass and individual high power LEDs with secondary optics,min. IP65 protection complete all as specified and directed by Engr-in-Charge. Make :Cromption LSTS-25-CDL /WIPRO-LRO2-291-XXX-57-XX C /Bajaj-BCLST 25W LED I V2

S & F air termination single pointed aluminium rod, single pointed at top and properly threaded at bottom end 300 mm long, 12 mm dia complete all as specified and directed by Engineer-in-charge

Supply and fixing earth continuity conductor or main earthing lead 25 x 3 mm aluminium strip laid in pipe/ fixed on wall or any other position incuding jointing by tinned copper/ brass nuts bolts and washers in addition to brazing at every joint complete all as specified and directed by engineer-in-charge.

Supply and fixing earth continuity conductor or main earthing lead 32 x 6 mm galvanised iron strip laid in pipe/ fixed on wall are any other position incuding jointing by tinned copper/ brass nuts bolts and washers in addition to brazing at every joint complete all as specified and directed by engineer-in-charge.

M & L for providing test point terminal block made out of Gun metal or phosphorous bronze of size 75 mmx75 mm x25 mm drilled and screwed including 03 nos 8 mm dia 25 mm long hexagonal head screws complete all as specified and directed by engineer-in-charge.

Material & labour for GI water tubing light grade,40 mm bore, duly threaded on one side for fixing socket as in air termination stand/post at roof top of building as specified & directed .

Supply and fixing alumimium rawl plugs 40 mm dia having internal threaded 12 mm dia and external thread of 40 mm dia and fixed on GI socked complete all as specified and directed by engineer-in-charge.

M&L for earthing with GI plate 600mm x 600mm x 6mm thick, burried directly in ground (earth pit not less than 2.25 meter deep below ground level) with top edge of plate not less than 1.5 Mtr below normal ground level, connecting to GI plate with GI strip 32 x 6mm upto 7.5 Mtr long from erth point to test point by means of bolts, nuts, check nuts, washers and provision of charcoal, salt etc including watering arrangement with 15mm dia GI pipe, 40mm dia light grade pipe for protection of GI strip upto 7.5 mtr, MS funnel, CI earth pit cover complete all as per electrical plate No 5 including necessary excavation and earth work in any type of soil complete all as specified and directed by engineer-in-charge.

M & L for PCC 1:2:4, type B-I using 20 mm graded stone aggregate.

Supply and fixing surface mounted square led downlight with AL die-cast body , finish with drop down PC diffuser to deliver low glare illumination with optimized heat sink for efficient heat dissipation 8Watt and Bajaj cat part NO-BGSLO SLEEK SURFACE 8W WH SQ /HAvalls/surya

Revoing and re-fixing LED tube light fitting, 1x 20-22 watts, 230 volt, basic all purpose surface and wall mounted led batten with polycarbonate housing & integrated electronic driver, pre-wired and fixed on walls with all fixing accessories such as screws, clips etc and connecting up with two core flexible copper conductor cable of size 24/0.20 sqmm complete all as specified and directed by Engr-in-charge.

Fixing only LED tube light fitting, 1x 20-22 watts, 230 volt, basic all purpose surface and wall mounted led batten with polycarbonate housing & integrated electronic driver, pre-wired and fixed on walls with all fixing accessories such as screws, clips etc and connecting up with two core flexible copper conductor cable of size 24/0.20 sqmm complete all as specified and directed by Engr-in-charge and issued under schedule B items from E/M store.

Fixing only LED mirror light fitting , type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed by Engr-in-charge and issued under schedule B items from E/M store.

Revoing and re-fixing LED mirror light fitting , type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed by engineer-in-charge.

Fixing only sheet metal enclosure MCCB DB, double door, 415 Volt ,vertical TPN 4 way with 200 Amps rated busbar including fixing MCCB/MCB, issued under schedule B items from E/M store complete all as specified and directed by engineer-in-charge.

Suppy and Fixing in repalcement 6 watt LED post top prism made up of unbreakable polycarbonate suitable for mounting on pole . including suitable size and hight of GI pole, marking necessary connections with testing complete all as specified and as directed by Engineer-in-Charge. Make CG/C&S/Bajaj/Havells/ Surya

Suppy and Fixing in repalcement 30 watt LED post top E- Top with low glare optical design acryclic diffuser suitable for mounting on pole . including suitable size and hight of GI pole, marking necessary connections with testing complete all as specified and as directed by Engineer-in-Charge. Make CG/C&S/Bajaj/Havells/ Surya

BIDAWAT ENTERPRISES

B.K. ROY & SONS