Construction and Extension of Community Health Centre (C.H.C.) under Block - Chas, District - Bokaro

Laying and Jointing PVC Pipe. Heading

Earth work in excavation in foundation trenches in hard soil (vide classification of soil item - A+B) and disposal of excavated earth as obtained to a distance up to 50M from the foundation trenches all complete as perbuilding specification and direction of E/I. B.C.D. S.O.R. Item No. 5.1.1 + 5.1.2

Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials, labours, royaly and taxes all complete as per building specification and direction of E/l. B.C.D. S.O.R. Item No. 5.1.10

Providing designation 75B one brick flat soling joints filled with local sand including cost of watering taxes, royalty all complete as per building specification and direction of E/I. B.C.D. S.O.R. Item No. 5.6.3

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size) B.C.D. S.O.R. Item No. 5.3.1.2

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level. 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size) B.C.D. S.O.R. Item No. 5.3.9.1

Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete. B.C.D. S.O.R. Item No. 5.3.17.1

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size) B.C.D. S.O.R. Item No. 5.3.10

Centering and shuttering including strutting, propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts. B.C.D. S.O.R. Item No. 5.3.17.6

Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers. B.C.D. S.O.R. Item No. 5.3.17.5

Providing designation 75B brick work in Cement Mortar (1:6) in foudation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing taxes and royalty all complete job as per building specificition and direction of E/l. B.C.D. S.O.R. Item No. 5.2.6

Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 20mm nominal size). B.C.D. S.O.R. Item No. 5.3.5

Providing designation 75B brick work in Cement Mortar (1:6) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing taxes and royalty all complete job as per building specificition and direction of E/l. B.C.D. S.O.R. Item No. 5.2.14

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size). B.C.D. S.O.R. Item No. 5.3.11

Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers. B.C.D. S.O.R. Item No. 5.3.17.5

Centering and shuttering including strutting, propping etc. and removal of form for Weather shade, Chajjas, corbels including edges. B.C.D. S.O.R. Item No. 5.3.17.19

Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platform. B.C.D. S.O.R. Item No. 5.3.17.3

Centering and shuttering including strutting, propping etc. and removal of form for Stairs, (excluding landings) except spiral-staircases. B.C.D. S.O.R. Item No. 5.3.17.7

Providing TMT steel reinforcement 8mm, 10mm, 12mm & 16mm dia bars as per approved design and drawing excluding carriage of M.S bar to work site, cutting, bending end binding with annealed wire with cost of wire removal of rust placing the rods in position all complete as per building specification and direction of E/I.8mm dia Bar -B.C.D. S.O.R. Item No. 5.5.4 :

B.C.D. S.O.R. Item No. 5.5.5 (a) : 10mm dia Bar -

B.C.D. S.O.R. Item No. 5.5.5 (b) : 12mm & above dia Bar -

Providing 12 mm thick cement plaster (1:4) with clean coarse sand of F.M. 1.5 with 1.5 mm cement punning including screening, curing with all leads and lifts of water, scaffolding, taxes and royalty all complete as per specification and direcition of E/l. B.C.D. S.O.R. Item No. 5.7.2 + 5.7.11

Providing 6mm cement plaster (1:4) in ceiling with clean coarse sand of F.M 1.5 including cost of screening, curing with all leads and lifts of water, scaffolding, taxes and royalty all complete as per building specification and direction of E/I. B.C.D. S.O.R. Item No. 5.7.6

Providing 12 mm thick cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding, taxes and royalty all complete as per specification and direcition of E/l. B.C.D. S.O.R. Item No. 5.7.3

Providing 12mm water proof cement plaster (1:3) with clean coarse sand of F.M 1.5 with 5% cico or any other approved water proofing compound including cost of screening, curing with all leads and lifts of water, scaffolding, taxes and royalty all complete as per building specification and direction of E/I. B.C.D. S.O.R. Item No. 5.7.14

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. (Size of Tile 600 x 1200 mm) D.S.R. Item No. 11.41A.1.3

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. D.S.R. Item No. 8.31

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent D.S.R. Item No. 11.56.1

Providing and fixing fan hook of 16mm dia TMT M.S. bar 1 meter long bent to required size and shape placed in position and fixed in R.C.C. slab/beam at the time of casting all complete as per building specification and direction of E/I. B.C.D. S.O.R. Item No. 5.5.13

Supplying, Fitting and fixing G.I. / M.S grill made of 20 x 6mm M.S. flat as per approved design and drawing, properly fabricated with joints continuous fillet welded and finished smooth, hoisting carriage of grill to work site hoisting as per building specification and direction of E/I. B.C.D. S.O.R. Item No. 5.5.12

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts,fasteners etc.). D.S.R. Item No. 10.28

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(Hot finished seamless type tubes) - TATA Structura only. D.S.R. Item No. 10.16.2

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters. 80x1.25 mm M.S. laths with 1.25 mm thick top cover D.S.R. Item No. 10.6.1

Providing and fixing ball bearing for rolling shutters. D.S.R. Item No. 10.7

Extra for providing mechanical device chain and crank operation for operating rolling shutters. D.S.R. Item No. 10.8.1

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), mesh and silicon sealent ). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. (Fenesta uPVC Windows only). DSR 9.147 D.1

Supplying, fitting and fixing collapsible gate of approved size and make properly fabricated with vertical double channels 20 x 10 x 2mm at 100mm centers and braced with M.S. flat diagonals 20 x 3mm with top and bottom rails of T.iron 40 x 40 x 6mm with 38mm dia steel pulleys complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of red lead paint, car riage, hoisting and taxes all complete as per building specification and direction of E/I. B.C.D. S.O.R. Item No. 5.5.14

Supplying, fitting and fixing good quality, well dressed and well seasoned teak wood work in chaukhat in doors, windows skylights, fanlights and C/W celetial windows openings, including wedge over all clamps complete including application of two coats of wood preservative of approved quality on the surface butting walls and lintels all completeas per building specification and direction of E/I. B.C.D. S.O.R. Item No. 5.4.2

Supplying, fitting and fixing 35mm thick solid core type non-decorative single leaf flush door shutter in door and windows with black board core blended with high quality phenol formal dehydes synthetic resine both side commercial veneered of standard make with oxidised iron fittings such as hinges, towerbolts, handle, cleat and sand blocks and taxes all complete as per building specification and direction of E/I. B.C.D. S.O.R. Item No. 5.4.38

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved mak+B50e conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed Portion : Powder coated aluminium (minimum thickness of powder coating 50 micron) D.S.R. Item No. 21.1.1.2

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron) D.S.R. Item No. 21.1.2.2

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item) : With float glass panes of 5.0 mm thickness D.S.R. Item No. 21.3.2

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete. D.S.R. Item No. 9.83

Supplying, fitting and fixing 20 guage G.C.I. Sheet gate fitted on M.S. Angle frame of size 60X60X6mm. Including cost of fabrication, providing necessary locking arrangement with haskal and domny duly fixed in P.C.C. (1:2:4) blocks of required size applying a priming red lead paint over steel work, taxes all complete as per drawing specification and direction of E/I. B.C.D. S.O.R. Item No. 5.5.29

Providing and applying white cement based wall putty of average thiickness 1mm of approved brand and manufacture over the plaster wall surface to prepare the surface even and smooth complete job as per building specification and direction of E/I. D.S.R. Item No. 13.80

Providing and applying putty of 2 mm thickness of approved brand and manufacture over the plaster wall surface to prepare the surface even and smooth complete job as per building specification and direction of E/I. D.S.R. Item No. 13.26

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade : New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm). D.S.R. Item No. 13.47.1

Providing two coats of plastic emulsion paint of approved shade and make over a coat of cement primer over new surface including preparing plastered surface by rubbing smooth with pumice stone or fine sand paper, applying putty wherever required, scaffolding washing of floor and taxes all complete as per building specification and direction of E/I. B.C.D. S.O.R. Item No. 5.8.21

Providing two coat of painting with ready mixed paint of approved shade and make over steel surface including cleaning the surface throughly, scaffolding and taxes all after removing dirt including scales smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specification and direction of E/I. B.C.D. S.O.R. Item No. 5.8.43

Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. D.S.R. Item No. 8.32

Providing and supplying Spandrel Glass Panels comprising of 6 mm thick heat strengthened monolithic float glass of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade so as to match the colour and shade of the IGUs in the vision panels etc. ,all complete for the required performances as specified, as per the Architectural drawings, as per the approved shop drawings, as specified, and as directed by the Engineer- in- Charge. D.S.R. Item No. 25.6

Providing and fixing 19mm thick both side balancing lamination factory pressed BWP grade marine ply as per IS 710 of approved brand boxes,shelves,racks,almirah,cupboard and drawer etc. including necessary nails,screws, hinges,handles etc. complete as per direction of Engineer-in-charge. DSR Item No. - 9.169

Providing & Fixing decorative high pressure laminated sheet of plain /wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality : 1.0 mm thick. DSR Item No. - 9.127.2

Providing and fixing stainless steel fancy handle of approved make fixed with SS screws etc. complete as per direction of Engineer-in-charge. (200 mm) DSR Item No. - 9.170.1

Providing and fixing stainless steel soft closing spring hinges at 0 degree hinges (hydraulic type) of approved make/brand to cupboard shutters with full threaded steel screws including making necessary recess in board and finished etc. complete as per direction of Engineer-in-charge. DSR Item No. - 9.171

Providing and fixing stainless steel soft closing heavy type telescopic drawer channels of approved make 500 mm long with screws etc. complete as per directions of Engineer- in-charge. DSR Item No. - 9.172

Supplying and fixing the Float glass panes of nominal thickness 6 mm (weight not less than 12.50 kg/sqm) as racks -do- -do- all complete as per specification and direction of E/I. DSR Code - 2407

Earth filling in foundation trenches and plinth in layers not exceeding 150mm thick well watered, rammed, fully compacted and finally dressed with earth obtained from excavation of foundation trenches with a lead of 50m and lift of 1.5m all complete as per building specification and direction of E/l. B.C.D. S.O.R. Item No. 5.1.7

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. B.C.D. S.O.R. Item No. 5.3.8

Providing 150mm wide brick drain in cement mortar (1:6) with av. 150mm clear depth and 125mm apron including cost of eartwork involved with 75mm cement concrete (1:4:3) over one brick designation 75A flat soling in proper grade and slope at the base the drain duly plastered in C.M. (1:3) with punning over exposed surface all complete as per building specification and direction of E/I. B.C.D. S.O.R. Item No. 5.10.34

Providing and laying factory made chamfered edge 60mm thick cement concrete paver block of M-35 grade with approved colour, design & pattern. Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. D.S.R. Item No. - 16.91.1

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) 110mm dia Single socketed pipes 75 mm diameter D.S.R. Item No. 12.41.2

12.41.2 - 110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. D.S.R. Item No. 12.42.1 Coupler 75 mm

12.42.4.1 Single tee without door 75x75x75 mm

12.42.5 Bend 87.5°75 mm bend

12.42.5.2 - 110 mm bend

12.42.6.1 Shoe (Plain)75 mm Shoe

12.42.6.2 - 110 mm Shoe

Providing 12mm cement plaster (1:4) with clean coarse sand of F.M. 1.5 with 1.5mm cement punning including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I. B.C.D. S.O.R. Item No. 5.7.2 + 5.7.11

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design D.S.R. Item No. 19.32.1

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever requiredWhite Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests. D.S.R. Item No. 17.1.1

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required.17.2.2 W.C. pan with ISI marked black solid plastic seat and lid. D.S.R. Item No. 17.2.2

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required. W.C. pan with ISI marked black solid plastic seat and lid. D.S.R. Item No. 17.3.2

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required. Range of two urinal basins with 5 litre white P.V.C. automatic flushing cistern D.S.R. Item No. 17.4.2

Supplying, fitting and fitting vitreous white glazed earthen ware wash hand basin of Parry or Hindustan or any other I.S.S. approved make supported on pointed C.I. or M.S. brackets 32m C.I. brass waste, 15mm dia C.I. body brass spindle stop cock of approved quality of weight not less than 350 grams, 32mm P.V.C. waste pipe 750mm long with brass coupling at one end and making plumber joints etc. all complete as per specification and direction of E/I. D.W.S.D. Item No. 3.2.5

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required. 17.10.1 - Kitchen sink with drain board D.S.R. Item No. 17.10.1.1

Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass unions complete, including painting of fittings and brackets, cutting and making good the wall wherever required. 17.11.2 - Size 600x450x200 mm D.S.R. Item No. 17.11.2

Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge. (a) 15 mm nominal dia D.S.R. Item No. 17.22B

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. 17.28.1 - Semi rigid pipe (32 mm dia) D.S.R. Item No. 17.28.1.1

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing .Rectangular shape 453x357mm D.S.R. Item No. 17.32 .2

17.32.4 - Rectangular shape 1500x450mm

Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. D.S.R. Item No. 17.33

Providing and fixing toilet paper holder : C.P. brass D.S.R. Item No. 17.34.1

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. 15 mm DSR 18.8.1

20 mm DSR 18.8.2

25 mm DSR 18.8.3

32mm DSR 18.8.4

Special type of CP Bathroom Fittings of ISI Marked (Jal, Jaquar,Marc or equivalent make)(ii) Pillar Cock (Long Neck) D.W.S.D. Item No M-961

(iii) Bib Cock

(ix) Bib Cock (Long Body)

(v) Angular Stop Cock

(x) Swan Neck Tap with left hand operating knob

(xix) Telephonic Shower with flexible Pipe

(xxi) Towel Rail - 24"

(xxii) Towel Ring

(xxiii) Soap Dish

(xxvi) Glass shelf - 22"

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. D.W.S.D. Item No. M079

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) 110mm dia Single socketed pipes. D.S.R. Item No. 12.41.2

Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.Single tee with door - 110mm D.S.R. Item No. 12.42

Bend 87.5° - 110mm

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FR PVC insulated copper conductor single core cable etc as required.Group C1.3.3

Wiring for twin control light point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed steel conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FR PVC insulated copper conductor single core cable etc as required.1.4

Wiring for light/ power plug with 2X4 sq. mm FR PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required. 1.5

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FR PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required.2 x 1.5 sq.mm + 1 x 1.5 sq.mm earth wire1.7.1

2 x 2.5 sq.mm + 1 x 2.5 sq.mm earth wire1.7.2

2 x 4.0 sq.mm + 1 x 4.0 sq.mm earth wire1.7.3

4 x 6.0 sq.mm + 1 x 6.0 sq.mm earth wire (Sub-Mains)1.7.4

4 x 10.0 sq.mm + 2 x 6.0 sq.mm earth wire (Sub-Mains+AC ODU)1.7.11

Supplying and drawing following sizes of FR PVC insulated copper conductor, single core cable in the existing surface/ recessed PVC/steel conduit including dismantling as required.2x1.5 sq mm 1.15.2

Supplying and fixing of following sizes PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.20 mm dia1.21.1

25 mm dia1.21.2

Supplying and fixing of following sizes of PVC/GI box on surface/recess with suitable size of phenolic laminated sheet cover infront including painting etc. as required :75 mm x 75 mm x 50 mm deep (4" x 4")1.22.1

72 mm x 146 mm x 48 mm deep (4" x 7") 1.22.2

121 mm x 173 mm x 48 mm deep (6" x 8") 1.22.6

210 mm x 206 mm x 48 mm deep (10" x 12")1.22.9

Supplying and fixing following modular switch/socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.5/6 amps, one way switch1.24.1

5/6 amps, two way switch 1.24.2

15/16 amps, one way switch 1.24.3

5/6 amp, 3 pin socket outlet 1.24.4

15/16 amps, 6 pin socket outlet 1.24.5

Supplying and fixing stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.1.25

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.1.26

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.1 or 2 Module (78mm x 78mm x 45mm)1.27.1

4/ 5 Module (78mm x 140mm x 50mm)1.27.2

12 Module (135mm x 205mm x 60mm)1.27.5

Supplying and fixing 2 pin 5 amp. Ceiling Rose on the exixting Junction Box / Wooden Blocks including connection etc. as required1.33

Supplying and fixing Batten / Angle Holder including connection etc. as required1.34

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FR PVC insulated, copper conductor, single core cable etc. as required.1.44

Installationof exhaust fan upto 450mm sweep in the existing opening including making the hole to suit the size of the above fan, making good the damage, connection, testing, commisioning etc. as required.1.48

Installationof exhaust fan upto 510mm sweep in the existing opening including making the hole to suit the size of the above fan, making good the damage, connection, testing, commisioning etc. as required.1.49

150/160 apms, 35kA fixed thermal setting2.2.4

200 amps, 4 pole2.7.6

250 amps, 4 pole2.7.7

8 way, Double door2.8.8

12 way, Double door2.8.9

Supplying and fixing of following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts,on surface /recess, complete with tinned copper bushbar, neutral link, earth bar, din bar, detachable gland plate, interconnections, including painting, earthing etc. as required.4 way(4+12)double door,horizontal type 2.9.4

6 way (4+18)double door horizontal type2.9.5

8 way (4+24)double door horizontal type2.9.6

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "B" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps, Single pole "B" series2.11.2

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.6/32 amps, Single pole2.12.1

6/32 amps, SPN2.12.3

50/63 amps, DP 2.12.7

40 amps, TPN 2.12.9

50/63 amps, TPN 2.12.10

Supplying and fixing following rating four pole 415volt, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.80/100 amps2.15.3

Earthing with copper earth plate 600 mm x 600 mm x 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. (but without charcoal/ coke and salt ) as required.3.6

Supplying and laying 8 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required.3.7

LIGHTNING PROTECTION Providing and fixing of lightning conductor finial, made of 25mm dia 300mm long GI tube, having single prong at top, with 85 mm fia 6 mm thick base plate including holes etc complete as required.4.2

Rivetting, sweating and soldering of copper/GI Tape (with another GI Tape, base of the finial or any other metallic object) as required.4.4

Providing and fixing GI tape 20mm x 3mm thick on parapet or surface of wall for lighting conductor as required (for horizontal run).4.7

Providing and fixing GI tape 20mm x 3mm thick on parapet or surface of wall for lighting conductor as required (for vertical run).4.8

Providing and fixing testing joint, made of 20mm x 3mm thick GI strip, 125mm long, with 4 Nos of brass bolts, nuts, check nuts and spring washers etc complete as required.4.12

12W LED Round Down Light 9.3.2

18/20W LED Round Down Light 9.3.4

1400mm (56") BLDC 5 star rating 32W Ceiling Fan 9.4.4

S.I.T.C of following rating surface mounted LED tube light fitting suitable for 230V 50Hz, single phase supply etc. complete as required.20/22 LED Tube Light 9.5.2

Providing and fixing 9" (230mm) Metal exhaust fan. M-774

Providing and fixing 15" (380mm) Metal Exhaust fan. M-776

Providing and fixing 16" (400mm) Wall mounted fan. M-777

Providing and fixing of Surface mountd Ceiling fixture(PORTICO) with 2x18 W P-L Lamp LED M-828

Providing and fixing of LED Bulb - 15/16 watt M-856

Providing and fixing of recess mounting LED Round down light - 15/16 watt M-827

Cost of drilling 200mm x 165mm x 125m deep bore well in all kinds of soil and rock in rural area for installation of pump set with hydraulic D.T.H. rig machine all complete! including supplying all materials, labours, tools, drilling rig, air compressor and equipment as well as fuel, lubricants for making boring and cost of transporting/charges of rig machine & other vehicles up to site of the work as per specification and direction of E/l. (DWSD - P-57, Sl.-119, M1035 )(a) Up to 50 mtr. Below G.L.

(b) Beyond 50 mtr. up to 125 mtr. Below G.L.

Supplying all tools,tackles & lowering of 200mm dia MS ERW casing pipe of 6mm wall thickness including welding charges, cost of pipe etc. all complete job as per specification and direction of E/I. (DWSD - P-58, Sl.-120, M1036 )

Supplying all materials, labours, tools and equipments for fitting and fixing 200mm dia. M.S. Cap over casing pipe complete job as per direction of E/I. (DWSD - P-58, Sl.-120, M1036 )

Supplying 32mm Dia CPVC pipes 3mtrs. Long screwed at both ends with seamless socket all complete job. (DSR)(ii) 32mm dia - DSR Code No. 8639

Supplying all tools ,equipment and labour for flushing ,washing and developing of drilled tube well to give clear water all complete jobs as per direction of E/I. (DWSD - P-65, Sl.-126, M1042 )

Supplying submersible pump set (KSB/KIRLOSKER/CRI make 3 HP Submersible pump ) conforming to IS : 8034 and motor conforming to IS : 9283 . pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/noryl impeller. Motor suitable for working on 415V ±10% , 3PH , 50Hz, AC Supply with cable guard thrust carbon/fiber bearing to withstand entire hydraulic thrust, water proof winding shall be provided. The pump set shall be suitable for direct coupling. Pump shall have suitable outlet as per manufacturers design. Anti thrust stream lined non return valve shall be provided with pump. 3 metre submersible copper conductor cable in single / double run shall be provided with each pump. Submersible pump 100mm dia (With Bronze / SS Impeller ) upto 8 Stages including all taxes, royalty, etc.all complete job as per direction of E/I. (DWSD - P-67, Sl.-139, M1055 )3.0 HP

Supplying fitting and fixing 3 core 4mm2 flat copper submersible cable FINOLEX/HAVELLS make including all taxes,royalty etc all complete job as per direction of E/I. (ED - P-36, M -1627)

Supplying and fixing G.I. Fittings of approved make and manufacrturer -do- -do- all complete as per specification and direction of E/I. (DWSD - Sl.-14, M930 )(E)Socket/Union32mm dia

Elbow 32mm dia

Providing and fixing PTMT extension nipple for water tank pipe, fittings of approved quality and colour. 25mm nominal bore, weighing not less than 62 gms DSR - 18.75.3

providing and fixing G.M. Non - Return valve horizontal / vertical type of approved quality as per specification and direction of E/I. Non - Return valve (Vertical) of 25mm dia weight not less than 375 gms DWSD - 3.1.7 B(iii)

Dismantling pucca brick or lime work including stacking serviceable materials in countable stacks within 15M. Lead and disposal of unserviceable materials with all leads all complete as per direction of E/I. B.C.D. S.O.R. Item No. 5.10.1

Dismantling plain cement or lime concrete work including stacking serviceable materials in countable stacks within 15M. Lead and disposal of unserviceable materials with all leads all complete as per direction of E/I. B.C.D. S.O.R. Item No. 5.10.2

Dismantling R.C.C. work including stacking serviceable materials in countable stacks within 15M. Lead and disposal of unserviceable materials with all leads all complete as per direction of E/I. B.C.D. S.O.R. Item No. 5.10.3

Dismantling patent stone floor including stacking serviceable materials in countable stacks within 15M. Lead and disposal of unserviceable materials with all leads all complete as per direction of E/I. B.C.D. S.O.R. Item No. 5.10.4

Dismantling thached shade roof with ballies rafters, purlines etc. Including stacking of serviceable materials in countable stacks within 15M. Lead and disposal of unserviceable materials with all leads as per direction of E/I. B.C.D. S.O.R. Item No. 5.10.9

Taking down C.A. Of G.C.I. Sheet in roofs with ridges including stacking the serviceable materials within 15M. Lead and disposal of unserviceable materials with all leads as per direction of E/I. B.C.D. S.O.R. Item No. 5.10.15

Taking down old door and window shutters including stacking serviceable materials within 15M,. Lead and disposal of unserviceable materials with all leads all complete as per direction of E/I. B.C.D. S.O.R. Item No. 5.10.10

Taking down chaukhats in doors including stacking serviceable materials within 15M,. Lead and disposal of unserviceable materials with all leads all complete as per direction of E/I. B.C.D. S.O.R. Item No. 5.10.11

Taking sown chaukhats in windows including stacking serviceable materials within 15M,. Lead and disposal of unserviceable materials with all leads all complete as per direction of E/I. B.C.D. S.O.R. Item No. 5.10.12

Taking down wooden beams, rafters, building frames etc. Of any type of roofing including stacking serviceable materials within 15M,. Lead and disposal of unserviceable materials with all leads all complete as per direction of E/I. B.C.D. S.O.R. Item No. 5.10.14

Carriage of materials including loading, unloading, stacking -do- -do- all complete as per specification and direction of E/I.Cement leads 10kM

Sand leads 15kM

Stone Chips leads 20kM

Bricks leads 8kM

Steel leads 10kM

Add. 18% GST

Add. 1% Labour Cess