Repairing and Renovation of Prison Kitchen of District Jail, Tinsukia

Amount

4.1.5- Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering- All work up to plinth lebel: 1:3:6- (1 Cement : 3 coarse sand (zone-III) : 6 graded stone aggregate 20 mm nominal size)

6.13- Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. 6.13.2- Cement mortar 1:4 (1 cement : 4 coarse sand).

4.11- Providing and laying damp- proof course 40mm thick with cenent concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size).

10.16.1- Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes

10.4- Providing and fixing 1 mm thick M.S. sheet sliding-shutters, with frame and diagonal braces of 40x40x6 mm angle iron, 3 mm M.S. gusset plates at the junctions and corners, 25 mm dia pulley, 40x40x6 mm angle and T-iron guide at the top and bottom respectively, including applying a priming coat of approved steel primer.

12.64- Providing & fixing at all heights, levels and locations Mill finish Aluminium alloy roofing sheets of alloy IS designation 31500, temper Hx8 conforming to IS 737 and dimensions as per IS code 2676 with characteristics of good formability and corrosion resistance. The profile sheets shall be fixed to truss members in slope or required pitch ort etc. etc. complete as per directions of the Engineer-In-Charge. (Cost of truss/frame work shall be paid separately). 12.64.2- 0.71 mm, troughed profile with center to center pitch of 200 mm, depth of 32 mm, overall profile width 1092 mm, cover width 1000mm.

12.66- Providing and fixing of Pre-coated colour or mill finish Aluminium Roofing Accessories in 0.71 mm thickness, Alloy 31500 (IS designation) [Aluminium Alloy (AA) 3004 (ISO designation)] For color, coating shall be 5-7 microns epoxy primer on both sides of the sheet and polyester top coat 15-18 microns, using self drilling/tapping SS screws of size 6x50mm with 3mm thick EPDM seal and SS plain washer complete: 12.66.1- Precoated/mill finish aluminium Ridges plain (500-600mm)

10.14.1 Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or etc. as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer in charge. Profile B- Fixing with adjustable lugs with split end tail to each jamb

11.41- Providing and laying vitrified floor tiles in different sizes (10mm thickness) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc. complete. 11.41.2- Size of Tile 600x600mm

13.1.2- 12 mm Cement plaster of mix 1:6 (1 cement : 6 fine sand)

13.2.2- 15 mm Cement plaster on the rough side of single or half brick wall mix 1:6 (1 cement :6 fine sand)

11.6- Cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement 11.6.1- 18mm thick.

12.45.- Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and etc. etc. 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) : 2011 (Board with BIS certification marks).

13.46.1- Finishing walls with Acrylic Smooth exterior paint of required shade: New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20kg/10sqm.

13.41.1- Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade: New work (two or more coats) over and including water thinnable priming coat with cement primer.

13.48- Finishing with Deluxe Multi surface paint system for interiors and exteriors using primer as per manufacturers specifications 13.48.3- Painting steel work with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work

9.96- Providing and fixing aluminium sliding door bolts I.S.I. marked anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete with nuts and screws etc. complete: 9.97.2- 300x16 mm

9.97- Providing and fixing aluminium tower bolts I.S.I. marked anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete with nuts and screws etc complete. 9.97.2- 250x10 mm

9.100- Providing and fixing aluminium handles I.S.I. marked anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete with nuts and screws etc complete: 9.100.1- 125 mm.

4.17- Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including finishing the top smooth.

17.10- Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making goodthe walls wherever required: 510x1040 mm bowl depth 225 mm

17.28- Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete Semi rigid pipe 40 mm dia

17.29- Providing and fixing 100 mm sand cast Iron grating for gully trap

17.36- Providing and filling the joints with spun yarn, cement slurry and cement mortar 1:2 ( 1 cement : 2 fine sand) in S.C.I./C.I. Pipes : 17.36.2 100 mm dia pipe

17.38- Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 100 mm dia. Sand cast iron S&S pipe as per IS: 1729

17.39- Providing and fixing plain bend of required degree. 100 mm dia Sand cast iron S&S pipe as per IS: 1729.

18.8- Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls 15 mm nominal outer dia Pipes.

32 mm nominal outer dia Pipes

18.15- Providing and fixing brass bib cock of approved quality 15 mm nominal bore

18.16- Providing and fixing brass stop cock of approved quality : 15 mm nominal bore.

Electrical worl :- 1.1- Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface/recessed steel conduit, with piano type switch, phenolic laminated sheet, suitable size MS box and earthing type point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group A

Group B

Group C

1.5- Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/recessed steel conduit a long with 1 No. 4 sq.mm FRLS PVC insulated copper conductor single core cable for loop earthing as required

1.7- Wiring for circuit/ submain wiring a long with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required. 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2 X 4 sq. mm + 1 X 4 sq. mm earth wire

1.35- Installation, Testing, Commissioning of wall bracket/ceiling fittings of all sizes and shapes containing upto two GLS/CFL/LED lamps per fitting, complete with all accessories including connections etc. as required

1.42- Installation, testing and commissioning of pre-wired fluorescent fitting/compact fluorescent fitting of all types, complete with all accessories and tube/lamp etc. including supplying and fixing ball and socket arrangement, 2 Nos. down rods of 200 mm dia X 1.6 mm thick steel conduit upto 30 cm length, painting and wiring the down rods and connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required

1.5- Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. Upto 450 mm sweep

Market Price of Exhaust Fan

2.1- Providing and fixing following capacity TP&N disconnector fuse switch unit inside the existing panel board with ISI marked HRC fuses including drilling holes in cubicle panel, aking connections, etc. as required 32 A TP&N

5.1- Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/coke and salt as required

5.7- Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/termination with GI thimble etc. as required

M/S PAPORI ENTERPRISE

RITURAJ SONOWAL