IMPROVEMENT TO MD ACCN AT AF STN ADAMPUR (PH-I)

Amount

BUILDING WORK

Demolition of brickwork built in cement mortar including all quoins, arches, pillars etc complete all as specified and as directed.

Demolition of Concrete (un reinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and as directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided complete all as specified and as directed.

Demolition of reinforced cement concrete as in chimney, cooking shelfs, Roofs, floors (other than ground floors), beams staircases, landing, chajjas, and similar suspended work complete all as specified and as directed.

Dismantling Brick tiles or terracing tiles, single layer on roofs complete all as specified and as directed.

Demolition of mud puska in roof, any thickness including plastering & leeping complete all as specified and as directed.

Dismantling cast iron or reinforced concrete or PVC drain pipes and fittings, jointed in cement mortar and taking out of trenches or from walls ( if required), 50 mm dia bore of pipe complete all as specified and as directed.

Dismantling cast iron or reinforced concrete or PVC drain pipes and fittings, jointed in cement mortar and taking out of trenches or from walls ( if required), 75 mm dia bore of pipe complete all as specified and as directed.

Dismantling cast iron or reinforced concrete or PVC drain pipes and fittings, jointed in cement mortar and taking out of trenches or from walls ( if required), 100 mm dia bore of pipe complete all as specified and as directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) not exc 1.50 Sqm each and removing to or from store complete all as specified and as directed by the Engineer-in-Charge

Taking down, Chowkhats or frames exc 1.5 sq. m but n exc 4 sq. m each but with shutters (without taking off shutters from the frame) complete all as specified and as directed.

Taking down shutters of any description exceeding 1.00 sqm but not exceeding 2.00 sqm each complete all as specified and as directed.

Taking down, easing, adjusting of old wooden shutters of any description exc. 1 sqm and not exc. 2 sqm each and refixing in same opening complete all as specified and as directed.

Taking down cement or cement lime plaster, any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water complete all as specified and as directed.

M&L for PCC 1:3 :6 type C-0 using 12.5 mm graded crushed stone aggregate as in filling back of chowkhats complete all as specified and as directed .

M&L for PCC 1:2:4, type B-1, using 12.5 mm graded stone aggregate as in roof kerbs or mud stops, rounded or chamfered on edges etc complete all as specified and as directed.

M&L for RCC 1:1.5:3 type A1 (using 20 mm graded stone aggregate) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies,canopies, deck slabs, shelves and the like ccomplete all as specified and as directed.

Supply only Liquid water proofing compound complete all as specified and as directed.

M&L for brick work with sub class ‘B’ (Old size) bricks straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and as directed.

M&L for brick work (EXCEPT BRICKS) with sub class ‘B’ (Old size) bricks straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and as directed.

M&L for Cutting chases pinning in, making good to facing where required and pointing in cement mortar (1:3) for concealed water tubing in brick walls cutting n.exc 10 cm girth complete all as specified and as directed.

M&L for Cutting holes in brick walls built in cement mortar (Depth of embedded portion of holdfasts or lugs measured from the face of the jamb into the wall), exc half brick but n exc one brick walls for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required complete all as specified and as directed.

M&L for formwork to (rough finished surfaces of flat concrete) soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and as directed.

S&F factory made 35 mm thick 2nd class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) complete all as specified and as directed.

S&F 35 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed.

S&F 25 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed.

S&F Solid PVC frame of size 50mm x 47mm made out of 50mm wood grain printed PVC sheet reinforced with MS square Tube and edges will be painted to match with printed sheet complete all as specified and as directed.

S&F Factory made soild PVC moulded door shutter with wood free EPS 30mm thick (stiles) with 2,4 or 6 raised panel design with 2mm thick moulded PVC sheet on front face and 2mm plain clour PVC sheet on back face complete all as specified and as directed.

S&F150 mm long aluminium anodized barrel tower bolts of extruded section complete all as specified and as directed.

S&F 200 mm long aluminium anodized barrel tower bolts of extruded section complete all as specified and directed.

S&F 300 mm long Aluminium alloy, anodised,sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed.

S&F Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21, size of hinges in 100 mm complete all as specified and as directed.

S&F for continuous (piano) hinges mild steel 30mm, bright finish or electrogalvanised complete all as specified and as directed.

S&F 300 mm long mild steel ordinary rat tail rod pattern door spring including roller and roller plate complete all as specified and as directed.

S&F 125 mm size, aluminium anodized handles, cast type complete all as specified and as directed.

S&F Hasp and staple, safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws, Size of hasp and staple 100 mm complete all as specified and as directed.

S&F in repair stainless steel drapery rod (capsule type) heavy duty, cut to size and erected in position including provison of brackets & decorative type finial (Two nos for each opening) complete all as apecified and as directed.

M&L for Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5 Liters per sqm of vertical surface of the sub-structure to a depth of 300mm including excavating channel along the wall and rodding etc. complete all as specified and as directed.

M&L for Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement : 2 coarse sand ) to match the existing floors complete all as specified and as directed.

S&F floor door stopper of aluminium alloy body and tongue anodised with hard drawn steel spring of 140mm overall length of cover plate fixed in floor complete all as specified and as directed.

S&F for stainless steel wire cloth 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples etc complete all as specified and as directed.

S&F IN REPAIRS for stainless steel wire cloth 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples etc complete all as specified and as directed.

S&F Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors ;frames; ladders; framed balusters; walk ways; railings; cooler frame; rungs framework of water tanks and similar work using any type of section conforming to Fe.290, Gde-E-165 etc complete all as specified and as directed.

S&F Mild steel TMT bars 10mm dia and over, cut to length, bent to shape reqd, incl cranking, bending spirally for hooping for columns, hooling ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

S&F Pressed steel frames made out mild steel sheet 1.25 mm thick, with size of frame 165 mm x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plates etc complete all as specified and as directed.

S&F Pressed steel frames made out mild steel sheet 1.25 mm thick, with size of frame 105 mm x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plates etc complete all as specified and as directed.

M&L for Cutting grooves in brick wall 75 mm wide and 65 mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and as directed.

M&L for 1 mm thick Decorative laminate type 1 of surface finish, colour and pattern as approved by the GE, fixed with approved adhesive as per manufacturer's instructions complete all as specified and as directed.

M&L for 18 mm thick (No of ply 12) plywood, grade BWP, type BB fixed with screws to timber frame work complete all as specified and as directed.

M&L for 12 mm thick (No of ply 7) plywood, grade BWP, type BB fixed with screws to timber frame work complete all as specified and as directed.

M&L for 18/19 mm thick, HDRM boards, grade 1 quality, exterior grade, decorative type with decorative face veneer on one face, fixed with screws to frame-work as in cupboard, kitchen cabinet and partition, shelf etc completed all as specified and as directed.

M&L for Granite 16-18 mm thick (of any type) work (table rubbed and polished) thick in steps, jambs, pillars, window-cills, cooking platforms slab and in front facia and the like in cement mortar (1:4) over and including 15 mm thick screed bed in CM (1:4) for laying of granite slab & pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed.

M&L for Rounding to edges of stone slabs one edge, such as in steps, cooking platform and other similar situations complete all as specified and as directed.

M&L for 75 mm thick cement concrete type C-1, 1:3:6 using 20 mm graded stone aggregate, finished even & smooth without using extra cement, as in plinth protection and making 6 mm wide joints in every 2.5 m interval, at every corner and at junction with wall and plinth, joints shall be sealed with joint sealing comound grade 'A' complete all as specified and as directed.

M&L for 25mm thick PCC 1:2:4 type B1 (using 20mm graded stone aggregate) as in sub base finished even and rough to receive the topping layer complete all as specified and as directed.

M&L for Machine cut Kota stone slab flooring 18-22mm thick as in floors etc over and including 20mm thick screed bed in cement mortar (1:6) laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing, cutting and polishing complete all as specified and as directed.

M&L for Machine cut Kota stone slab 18-22mm thick on vertical surfaces as in staircase riser skirting/dado etc in single piece (of length not more than 1200mm) over and including 10 mm thick rendering in cement mortar (1:4) laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing, cutting and polishing complete all as specified and as directed.

Dismantling floor, hearth or wall tiling or stone chips including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and as directed.

M&L for rendering 10 mm thick on brick or concrete surface of ceiling finished even and smooth in CM 1:3 complete all as specified and as directed.

S&F 4 mm thick Sheet glass, ordinary quality, in squares n exc 0.5 sqm each pane complete all as specified and as directed.

S&F 4 mm thick Figured glass, pin head type in squares n exc 0.5 sq.m each pane complete all as specified and as directed.

M&L for Preparation of new wooden surfaces of any descriptionover 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

M&L for preparation of old painted wood and wood based surfaces of any description not other wise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

M&L for preparation of old painted wood and wood based surfaces of any description not other wise described over 10cm width or girth and applying two coats of synthetic enamel paint complete all as specified and as directed.

M&L for Preparation of new steel surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamelled paint over one coat of red oxide primer complete all as specified and as directed.

M&L for peparation of old painted steel & iron surfaces of any description not other wise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

M&L for Writing letters or figures by specialist/professional painter (Block, Roman, Italic or indian) with thick black synthetic enamel paint not exc. 30cm height on white base complete all as specified and as directed.

S&F Galvanised steel water tubes 15mm bore medium grade with all fitting and fixed to walls, ceilings or laid in floors complete all as specified and as directed.

S&F Galvanised steel water tubes 20mm bore medium grade with all fitting and fixed to walls, ceilings or laid in floors complete all as specified and as directed.

Taking down 15mm bore Galvanised steel water tubes and connection, including cleaning for refixing complete all as specified and as directed.

Taking down 20mm bore Galvanised steel water tubes and connection, including cleaning for refixing complete all as specified and as directed.

S&F (EXCEPT TUBING) Galvanised steel water tubes 20mm bore medium grade with new fitting and fixed to walls, ceilings or laid in floors complete all as specified and as directed.

Dismantling water tanks PVC or RCC capacity exc 250 ltr & n exc 500 ltr complete all as specified and as directed.

Dismantling water tanks PVC or RCC capacity exc 500 ltr & n exc 1000 ltr complete all as specified and as directed.

S&F 500 ltrs rotational moulded polyethylene water storage tanks (cylindrical verical with closed top) hoisted and fixed in position complete all as specifed and as directed.

S&F 1000 ltrs rotational moulded polyethylene water storage tanks (cylindrical verical with closed top) hoisted and fixed in position complete all as specifed and as directed.

S&F in repairs bib taps, cast copper alloy with capstan head, CP fancy type with foam flow, long body shank, screwed down, screwed for 15mm bore iron pipe or brass ferrule complete all as specified and as directed.

S&F in repair Bib tap standard of PTMT any colour high pressure screwed for iron pipe (Minimum weight 15mm-90gms) complete all as specified and as directed.

S&F in repairs Centre hole basin mixture for mixing hot and cold water, cast copper alloy, with capstan heads, chromium plated, screwed down, high pressure, with long screwed shanks and fly nuts fancy type screwed for 15mm bore iron pipe complete all as specified and as directed.

S&F in repairs Pillar taps, brass chromium plated, fancy type, foam flow, screwed down high pressure screwed for 15mm bore iron pipe complete all as specified and as directed.

S&F in repairs wall mixture telephonic, cast copper alloy, chromium plated, with crutch and including hand shower, 1.5 mtr flexible tube ABS single flow, screwed down, high pressure, screwed for 15mm bore iron pipe complete all as specified and as directed.

S&F in repair sink mixer fancy type with regular spout with hot or cold mounted tap, cast copper alloy, chromium plated, screwed down, high pressure, with long screwed shanks and fly nuts screwed for 15mm bore iron pipe complete all as specified and as directed.

S&F in repairs cast copper alloy stop cock/angle cock fancy type CP with long shank screwed down high pressure with crutch or butterfly handle screwed both ends to 15mm bore iron pipe complete all as specified and as directed.

S&F in repairs cast copper alloy two ways angle cock fancy type CP with long shank cast copper alloy screwed down high pressure with crutch handle screwed both ends to 15mm bore iron pipe complete all as specified and as directed.

S&F in repairs cast copper alloy concealed stop cock type CP with long shank screwed down high pressure with crutch or butterfly handle screwed both ends to 15mm bore iron pipe complete all as specified and as directed.

S&F in repairs Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for 20mm bore iron pipe complete all as specifed and as directed.

S&F in repairs Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule, 20mm bore iron pipe complete all as specifed and as directed.

S&F in repairs PVC connections 15mm size with PTMT nuts of length 450 mm complete all as specified and as directed.

S&F in repairs PVC flushing cistern 10 ltr capacity, valve less syphonic action type low level with and including ball valve float & handle, flush pipe, waste pipe & brackets complete all as specified and as directed.

S&F in repairs Bathroom mirror Cabinet (PTMT alloy) of size 622mm x 422mm fixed in position with SS screws complete all as specified and as directed. Make: Prayag CAT No: 555 or Euqivalent approved model of Make as specified here-in-after.

S&F in repairs Soap dish, vitreous China white, approximate size 160x 160x90mm complete all as specified and as directed. .

S&F in repairs Stainless steel sink double bowl with double drainage board with glossy finish made out of 1.00mm thick sheet for kitchen or laboratory with plugs, waste pipes, Chromium plated waste couplings, washers, brackets, connecting union etc overall size 2000mm x510 mm with size of both bowls 460mm x 400mm x 215 mm complete all as specified and as directed.

S&F in repairs Stainless steel sink made out of 1.00mm thick sheet for kitchen or laboratory with plug, waste pipe, washer including cantilever cast iron brackets, connecting union etc overall size 495mm x 420 mm with bowl size 410mm x 330mm x 160 mm complete all as specified and as directed.

S&F in repairs One piece Vitreous China wash down water closet pan with integrated cistern, seat cover soft closing and twin flush system of size 680x370x 50 mm white colour including necessary fixing acessories complete all as specified and as directed.

S&F in repairs Vitreous China wash down water closet pan (pedestal pattern), white colour including necessary fixing acessories complete all as specified and as directed.

S&F in repairs vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap and flushing pipe including making good to floor complete all as specified and as directed.

S&F in repairs brass chromium plated shower roses with swivel joints, 125 mm size in square with CP long shank arm including fixing to steel pipe or union complete all as specified and as directed.

S&F in repairs Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia bore pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and as directed.

S&F in repairs Chromium plated, stainless steel, jet spray including 1.5 mtr long flexible tube butterfly type including necessary connection for wash down water closet (pedestal pattern) complete all as specified and as directed.

S&F in repairs Vitreous China wash basin, white, flat back, size 550x400 mm with pedestal, PVC waste pipe, chain and plug and porcelain stopper complete all as specified and as directed.

S&F in repairs Vitreous China wash basin, white, flat back, size 450x300 mm, PVC waste, chain and plug and porcelain stopper (including brackets) complete all as specified and as directed.

S&F in repairs stainless steel plate rack made of 0.61 mm thick sheet, over all size 600mmX750mm complete all as specified and directed.

S&F in repairs stainless steel grating doom 125 mm dia size with waste hole complete all as specified and as directed.

S & F in repairs Brass chromium plated, tubular towel rails 20 mm dia, D- type, 60 cm long between flanges complete all as specified and as directed.

S&F in repairs Sheet glass Shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and as directed.

S&F in repairs Corner glass shelf, 5mm thick glass, 9" wide, fixed with suitable mild steel CP brackets, nuts & bolts complete all as specified and as directed.

S&F in repairs Shelf of PTMT fixed with and including chromium plated brass screws and wooden/ plastic cleates complete all as specified and as directed.

S&F 100mm dia bore cast iron spun type soil waste and vent pipe in any length with or without ears with cement joints, laid in trenches or in floors (in short pieces) complete all as specified and as directed.

S&F 75mm dia bore cast iron spun type soil waste and vent pipe in any length with or without ears with cement joints, laid in trenches or in floors (in short pieces) complete all as specified and as directed.

S&F 100mm dia bore cast iron spun type soil waste and vent pipe in any length with or without ears with cement joints fixed to wall including holder bats complete all as specified and as directed.

S&F 75mm dia bore cast iron spun type soil waste and vent pipe in any length with or without ears with cement joints fixed to wall including holder bats complete all as specified and as directed.

S&F 50mm dia bore sand cast soil waste and vent pipe in any length with or without ears with cement joints fixed to wall including holder bats complete all as specified and as directed.

S&F cast iron Bends (any radius), diminishing pieces or tapers (larger bore measured) 100mm bore of pipe complete all as specifed and as directed.

S&F cast iron Traps ‘P’ or ‘S’ 100mm bore of pipe complete all as specifed and as directed.

S&F Cast iron cowls 75 mm bore of pipe complete all as specifed and as directed.

S&F 75 mm bore PVC (SWR) pipes of pressure rating 6Kgf/cm2, single socketed, in any length with rubber ring joints, laid in trenches or in floors, including holder bats etc complete all as specifed and as directed.

S&F 110 mm bore PVC (SWR) pipes of pressure rating 6Kgf/cm2, single socketed, in any length with rubber ring joints, laid in trenches or in floors, including holder bats etc complete all as specifed and as directed.

S&F in repairs 110mm bore of pipe PVC (SWR) bends/shoe of any radius complete all as specifed and as directed.

S&F in repairs 75mm bore of pipe PVC (SWR) bends/shoe of any radius complete all as specifed and as directed.

S&F in repairs 75mm bore of pipe PVC (SWR) junction, single (single T) equal or unequal complete all as specifed and as directed.

S&F in repairs cast iron floor trap with grating including jointing to 75mm bore of waste pipe, fixed in cement concrete type B1 (1:2:4 ) using 20mm graded stone aggregate complete all as specifed and as directed.

S&F Factory made steel windows with side hung shutter with glazing bars, each shutter having 02 No. box type hinges & two nos. tower bolts of size not less than 150mm size and peg stays, dovetailed or welded, including one shop coat of zinc chromate primer complete all as specifed and as directed.

S&F Factory made steel windows with side hung shutter with out glazing bars, each shutter having 02 No. box type hinges & two nos. tower bolts of size not less than 150mm size and peg stays, dovetailed or welded, including one shop coat of zinc chromate primer complete all as specifed and as directed.

S&F Power coated aluminium (minium thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS 733 and IS : 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/paneling, C.P brass/stainless steel screws complete all as specifed and as directed.

S&F Powder coated aluminium (minium thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS : 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P brass/ stainless steel screws complete all as specifed and as directed.

M&L for 40mm thick brick tiles laid on concrete roof padding over and including 15 mm thick cement screed bed in CM (1:6) using grey cement, jointed and grouted flush in cement mortar (1:3) mixed with 5% of crude oil by weight of cement complete all specified and as directed.

M&L for 40mm thick brick tiles (EXCEPT TILES) laid on concrete roof padding over and including 15 mm thick cement screed bed in CM (1:6) using grey cement, jointed and grouted flush in cement mortar (1:3) mixed with 5% of crude oil by weight of cement complete all specified and as directed. Note :- Retrieved material (Tiles) against item No. 1.05 shall be reused after cleaning and cost of cleaning is deemed to be included in the unit rate quoted for this item.

M&L for Preparation of newly plastered/RCC surfaces, making the surface completely dry and applying a coat of bitumen primer, having density in range of 0.87 to 0.89 kg/litre at 25 degree centigrade and viscosity of 70 to 160 CPS, manufactured by same manufacturer @ 0.4 ltr/sqm shall be applied and after drying of primer for 24 hours apply APP modified water proofing membrane with non-woven polyster reinforcement, 3mm thick superior multipolymeric, weighing not less than 3.00 Kg/sqm with properties of high penetration and centre core consisting of 90 micron high molecular high density polyetylene (MHHDPE) film consisting of five layers laid with torching application to the surface complete and sealing the side as well as end laps with torch (Overlaps shall not be less than 10cm in longitudnal direction and 15cm in traverse direction and shall be bonded with bitumen primer and levelled by heating the overlaps with brutane torch.) complete all as specifed and as directed.

M&L for plain cement concrete 1:2:4 type B1 (20 mm graded aggregate) as in roof padding including necessary formwork and maintaing the requisite slope, finishing the surface even and smooth complete all as specified and as directed.

M&L for Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust and brushing neat cement slurry @ 3.0 kg/sqm complete all as specified and as directed.

M&L for Coloured Glazed ceramic tiles in vertical surfaces 600X300x 6-7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match with and including 10mm thick rendering in CM 1:4 on fair faces of brick work or concrete surfaces as backing coat complete all as specified and as directed.

M&L for Coloured Non-skid Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with and including 15 mm thick screed bed or bedding layer in CM 1:4 for laying floor finishes complete all as specified and as directed.

M & L for dark shade (Double Charged), Vitrified Ceramic tiles 09-10 mm thick (square/ rectangular) polished, area of each tile exceeding 0.42 sqm but not exc 1.00 sqm as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 20 mm thick screed bed or bedding layer in CM 1:4 complete all as specified and as directed.

M&L for dark shade (Double Charged), Vitrified Ceramic tiles 09-10 mm thick (square/ rectangular) polished, area of each tile exceeding 0.42 sqm but not exc 1.00 sqm, as in skirting and other vertical surfaces etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick rendering in CM 1:4 complete all as specified and as directed.

M&L for Coloured Non-skid Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick Screed bed or bedding layer in CM 1:4 complete all as specified and as directed.

M&L for rendering 15 mm thick in CM 1:6 on faces of brick work or concrete surface finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15 mm thick in CM 1:4 on fair faces of brick work using WPC @ 3% by weight of cement, surface finished fair & even complete all as specified and as directed.

M&L for Prepration of newly plastered wall surfaces of any description and applying Two coats of water based Acrylic distemper over and including a coat of primer of the same manufacturer complete all as specified and as directed.

M&L for preparation of old plastered/unplastered surfaces of walls and applying Two coat of white wash complete all as specified and as directed.

M&L for Prepration of newly plastered wall surfaces of any description and applying Two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/ltr and UV resistance as per IS 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade (company depot tinted ) with silicon additives @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 ltr/10 sqm complete all as specified and as directed.

M&L for Complete removal of existing treatment of any description, including prepration of wall surfaces of any description and applying Two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/ltr and UV resistance as per IS 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade (company depot tinted ) with silicon additives @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 ltr/10 sqm complete all as specified and as directed.

M&L for Complete removal of existing treatment of any description, including prepration of wall surfaces of any description and applying Two coats of water based Acrylic distemper over and including a coat of primer of the same manufacturer complete all as specified and as directed.

M&L forPrepration of newly plastered ceiling surfaces of any description and applying Two coats of water based Acrylic distemper over and including a coat of alkali resistant primer complete all as specified and as directed.

M&L for Complete removal of existing treatment form the ceiling surfaces and applying Two coats of water based Acrylic distemper over and including a coat of alkali resistant primer complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of ceiling and applying three coats of white wash on ceiling, complete all as specified and as directed.

M&L for preparation of old plastered surfaces of ceiling and applying one coat of white wash complete all as specified and as directed.

S&F 100mm bore of pipe cast iron Bends (any radius), diminishing pieces or tapers (larger bore measured) with oval access door etc complete all as specifed and as directed.

S&F 75mm bore pipe cast iron Bends (any radius), diminishing pieces or tapers (larger bore measured) with oval access door etc complete all as specifed and as directed.

S&F100mm bore of pipe cast iron Branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches or 'T' piece with oval access doors etc complete all as specifed and as directed.

S&F 75mm bore of pipe cast iron Branch pieces, Double (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches or 'T' piece with oval access doors etc complete all as specifed and as directed.

M&L for Applying two coats of two component elastomeric acrylic polymer modified cementitious waterproofing coating, Smartcare Ultra block 2K or equivalent, having 215% elongation as per ASTMD-2370, resisting 5 bars hyrostatic pressure as per DIN 1048, crack briding upto 3.50 mm as per EN 1062-7 and sprinkling dry fine sand over wet second coating complete all as per maunfacturer's specifications. NOTE: - Unless otherwise recommended by manufacturer, the mixing ratio of the components shall be 6 parts of powder and 4 parts liquid without any water addition in the mixing.

M&L for Uprooting tree/plants upto 30 cm girth from wall or any part of building upto double storey buildings completly to the entire satisfaction of Engineer-in-Charge, making good the disturbed portion and filling holes in cement mortar (1:3) or PCC (1:2:4) type B-1 using 20mm graded stone aggregate to match with existing surfaces and removal of rubbish outside MOD land complete all as specifed and as directed.

S&F 18mm thick PVC Celuka Foam board of plain color fixed with screws, solvent cement/adhesive as in sides, top, bottom and shelves inside the kitchen cabinet complete complete all as specifed and as directed.

S&F 18mm thick PVC Celuka Foam board of one side prelam/rigidlam and other side balancing laminate colour to make kitchen cabinet shutter/drawer front complete complete all as specifed and as directed.

S&F 12mm thick PVC Celuka Foam board of plain white color fixed with screws, solvent/adhesive as in wall mounted kitchen cabinet back and pull out drawer sides complete complete all as specifed and as directed.

S&F 6mm thick PVC Celuka Foam board of plain white color fixed with screws, solvent/adhesive as in kitchen cabinet back covering and pull out drawer base complete complete all as specifed and as directed.

S&F 20mm wide & 1mm thick (PVC EDGE BENDING) of PVC, pasted on edges with suitable adhesive complete complete all as specifed and as directed.

S&F stainless steel Auto Closing Hinges openable at 0 degree for kitchen cabinet shutters complete all as specifed and as directed. Make: Hettich, Ebco, Prime or equivalent as specified here-in-after.

S&F stainless steel ball bearing runners 45mm Telescopic channel (20 inch) full extension load capacity 50kgs complete all as specifed and as directed. Make: Hettich, Ebco, Prime or equivalent as specified here-in-after.

S&F stainless steel handles 100mm size for kitchen cabinet shutters complete all as specifed and as directed. Make: Hettich, Ebco, Prime or equivalent as specified here-in-after.

S&F chrome plated stainless steel wire basket (storage basket) pull out type for large utensills, size 486x500mm with necessary fixing clips etc.ccomplete all as specifed and as directed. Make: Hettich, Ebco, Prime or equivalent as specified here-in-after.

S&F chrome plated stainless steel wire basket (cup and soucer basket) pull out type, size 530x500mm with necessary fixing clips etc. complete all as specifed and as directed. Make: Hettich, Ebco, Prime or equivalent as specified here-in-after.

S&F chrome plated stainless steel wire basket (jar basket) pull out type, size 536x500mm with necessary fixing clips etc. complete all as specifed and as directed. Make: Hettich, Ebco, Prime or equivalent as specified here-in-after.

S&F chrome plated stainless steel wire basket (Thali basket) pull out type,size 380x500 mm with necessary fixing clips etc. complete all as specifed and as directed. Make: Hettich, Ebco, Prime or equivalent as specified here-in-after.

S&F chrome plated stainless steel wire basket pull(cutlery basket) out type, size 380x500 mm with necessary fixing clips etc. complete all as specifed and as directed. Make: Hettich, Ebco, Prime or equivalent as specified here-in-after.

S&F chrome plated stainless steel wire basket pull (storage/plain basket) out type, size 380x500 mm with necessary s fixing clips etc.complete all as specifed and as directed. Make: Hettich, Ebco, Prime or equivalent as specified here-in-after.

S&F chrome plated stainless steel wire basket pull (Bottle pull out) out type, size 150 to 200 mm with necessary sliding frame structure, fixing clips etc. complete all as specifed and as directed. Make: Hettich, Ebco, Prime or equivalent as specified here-in-after.

INTERNAL ELECTRIFICATION

Taking down copper/aluminum point wiring (light, fan, socket or power) complete including u/s fittings such as switches, ceiling rose, holders, sockets etc. and making good disturbed surfaces on walls/floors etc complete all as specified and as directed.

M&L for point wiring complete with 1.5 sqmm single core pvc insulated unsheathed FRLSH cable 1100 volts grade ISI marked with multi stranded copper conductor drawn through and including PVC conduit medium grade and its accessories ISI marked concealed in wall/fixed to roof ceiling etc with and including provision of 1.5 sqmm PVC insulated multistranded unsheated copper conductor cable FRLSH ISI marked as earth continuity conductor, fabrciated sunken terminal box made out of 1.22 mm thick sheet steel duly painted concealed in walls, with 3 mm thick bakelite sheet ISI marked top cover with brass/chromium plated screws and cup washers for housing switches, socket outlets, fan, regulators etc for the following, complete all as specified and as directed. Note :- (i) The chases in the wall shall be cut with elect cutter (ii) The disturbed surfaces of wall shall be made good with cement plaster 1: 4 including matching the surfaces with two coats of white wash / colour wash/ water based acrylic emulsion all as per existing finishes and to the entire satisfaction of Engr-in-Charge.

One light/fan/bell point controlled by one switch.

One light point controlled by two switch.

One 3 pin 5 amps socket point on independent board.

One 3 pin 5 amps socket point on same board.

All as per item No. 2.72 here-in-before but point wiring using 2.5 sqmm as main wire & 2.5Sqmm as continous earth wire, for one 15Amps socket outlet point on independent board controlled by one single pole, one way switch complete all as specified and as directed.

S&F switch piano flush button single pole one way, 5 Amps complete all as specified and as directed.

S&F switch piano flush button single pole two way, 5 Amps complete all as specified and as directed.

S&F socket outlet mulitpurpose 5 pin, 5 Amps, flush type, complete all as specified and as directed.

S&F switch piano flush button single pole one way, 15 Amps complete all as specified and as directed.

S&F socket outlet mulitpurpose 6 pin, 15 Amps, flush type, complete all as specified and as directed.

S&F ceiling rose surface bakelite 65x50mm with three terminals complete all as specified and as directed.

S&F lamp holder, PVC/ploycarbonate type with back plate suitable for batten fittings complete all as specified and as directed.

S&F stepped type electronic fan regulator flush type on white hylam laminated sheet as required complete all as specified and as directed.

S&F buzzer ding dong AC, 230 volts, single pole complete all as specified and as directed.

S&F Bell push, flush type, 5 Amp complete all as specified and as directed.

S&F LED light fitting 1x20W, 220V AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.

S&F LED light fitting 1x10W, 220V AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.

S&F LED light fitting 1x9W/10W bulk head luminaires including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.

Disconnecting, taking up/down the existing electic geyser and refixing the same in other/same location with and including new fixing material etc complete all as specified and directed.

M&L for sub main wiring with 2 runs of 6 sqmm PVC insulated unsheathed 1100 volt grade multistranded copper conductor with and including PVC conduit of suitable size and provision of one run 6 sqmm PVC insulated unsheathed single core copper conductor as earth continuity , connected to earth dolly inclusive of all accessories complete all as specified and as directed. Note :- 3 Runs of 6 Sqmm wire and one run of PVC conduit shall be measured as one unit .

M&L for sub main wiring with 2 runs of 4 sqmm PVC insulated unsheathed 1100 volt grade multistranded copper conductor including PVC conduit of suitable size and provision of one run 4 sqmm PVC insulated unsheathed single core copper conductor as earth continuity , connected to earth dolly inclusive of all accessories complete all as specified and as directed. Note :- 3 Runs of 4 Sqmm wire and one run of PVC conduit shall be measured as one unit .

S&F sheet metal enclosure,TPN DB loadline double door for fixing of MCB and MCCB, isolator, RCCB and RCBO, 415 volt with 100 Amps rated bus bar in and including 100 Amps MCCB 4 Pole for each phase complete all as specified and as directed.

S&F sheet metal enclouser DB SPN, 8 way with 200 Amp rated bus bar, 240 V, double door, for fixing MCB's isolatores etc. having IP-43 protection, flush mounting complete all as specified and as directed.

S&F 240 V, 10 KA'C' curve miniature circuit breaker (MCB) SPN 32 AMP in the MCB DB complete with connection, testing and commissioning complete all as specified and as directed.

S&F MCB SP with over load protecton and rupturing capacity 10 KA, 'C' curve of rating 06 to 32 Amp single phase complete all as specified and as directed.

M&L for earthing complete with GI earth plate electrode of size 600mm x 600mm x 6mm thick burried directly in ground vertically (depth of pit not less than 2.25 m below normal ground level), with top edge of earth plate not less than 1.5 m below normal ground level, earth plate surrounded from all sides by 15cm thick packed alternate layers of charcoal dust and common salt, electrode connections using galvanized lead wire 4mm dia (upto body of equipment) by means of nuts, bolts, check nuts & GI washers, connected to main switch board or main control board or test point, protected by galvanized iron pipe light grade 15mm dia bore, and watering pipe 20 mm bore GI light grade pipe with funnel & wire mesh, including all necessary excavation & earth work, PCC chamber in PCC (1:2:4) type B-1 & RCC cover, all as shown in electrical plate No 3 of MES Schedule Part-I (2009), testing on completion, including taking out old earthing materials and removal complete all as specified and directed. Note(s) :- (i) RCC pit cover shall be pre-cast of RCC (1:2:4) type B-1, 80mm thick reinforced with XPM not less than 4Kg/Sqm. (ii) PCC chamber shall be constructed 500 mm away from the edge of earth pit. (iii) Rate shall include GI lead wire and protection pipe of length 7.5m, GI pipe beyond 7.5m length required at site shall be measured and paid separately. (iv) Earth resistance should be less than 3 Ohm. In case the test results are not found below 3 Ohm, complete earthing will be redone without any extra cost to Govt.

Taking down wall mounted/ ceiling fan and refixing the same into the exiting location complete all as specified and as directed.

S&F ceiling fans complete with blades, down rods, electronic regulator and accessoreis, 230V, 1200mm sweep, Minimum air delivery 210 CFM with service value 6.00 (BEE) Five star rated with brushless direct current motor (BLDC) complete all as specified and as directed.

Supply, laying, jointing, testing and commissioning of Low Tension (LT) XLPE insulated and armoured, heavy duty, electric power cable, cross sectional area 35 Sqmm 3.5 core aluminum conductor 1100volts grade under ground cable including both side connection with cable lugs etc, laid in trenches, along poles or passing through pipes or laid under floor or through walls etc, complete all as specified and as directed. Note: Returning filling & removal of earth, sand cushioning and bricks for protection of cable shall be measured and paid separately.

Excavation in trenches in soft/loose soil not excedding 1.5 metre wide and not exceeding 1.5 metre deep for laying/taking out cables and foundation of poles etc and getting out complete all as specified and as directed.

Returning, filling in trenches (soil), including spreading, leveling and well ramming in lavers not exceeding 25cm thick complete all as specified and as directed.

Removal of surplus excavated soil to a distance not exceeding 50metre and depositing where directed at a level not exceeding 1.5metre above the starting point, complete all as specified and directed.

M&L for sand cushioning with a layer of dry river sand and punning to provide required cover as per SSR part -I complete all as specified and as directed. Note : Punned down thickness (overall 18cm) shall be considered for measurement and payment.

M&L for locally available, sub class 'B' bricks (old size), laid flat and dry perpendicular to the direction of cable adjacent to each other, in trenches over the cable for protection, complete all as specified and as directed.

M&L for galvanised steel water tubing Light grade , of size 40 mm bore with necessary GI fittings laid in floors/ wall complete all as specified and as directed.

S&F Single pole and netural enclosure with a two pin and earth plug and socket complete with one 20 Amp MCB single pole neutral complete all as specified and as directed.

S&F exhaust fan of sweep 300mm, metallic body complete with louvers shutter, voltage 230V, 50 Hz, single phase, 1200 RPM, Copper winding, connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.

Note: The Total amount shall subject to adjustment of credit of Rs.1,90,557.00 for old Materials as per Schedule of Credit.

M/s Sahib and Company

M/S Kuldip Construction Co.