PROVISION OF CERTAINS REVENUE WORK and MINOR WORK IN THE AOR OF AGE BRI and BRII EMI and EMII UNDER GE 865 EWS

Amount

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 5cm deep and getting out in hard/dense soil

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in hard/dense soil

M&L PCC 1:4:8 Type D2 (using 40mm graded stone aggregate) as in foundation, filling and mass concrete. complete all as specified and directed.

M/L Precast cement concrete solid blocks masonry PCC 1:3:6 type C1, using 20 mm graded crushed stone aggregate & set in cement motar 1:6 complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm

Removal excavated material exc 250m and n.exe 500m and depositing where directed at a level n.exc 1.5 m above the starting point.

M&L Reinforced Cement concrete nominal mix type B1 1:2:4 (20 mm graded Aggregate) in Beams , Cantilievers, bressummers, lintles over 1.5 m span.

M&L Reinforced Cement concrete nominal mix type B1 1:2:4 (20 mm graded Aggregate) in columns, pillars, piers, posts and struts complete all as specified and directed by Engr-in-charge.

Form work to sides and soffits of floor or roof beam, beam, hauchings, girders, bressum-emers, lintels, cantilevers, shelves incl supports overhangs etc also splays between floors and beams all as specified.

S&F for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with & including mild steel wire (annealed) not less than 0.9mm dia or securing with clips Reinforcement 10 mm and over

All as per item No. above here-in- before but up to and including 6 to 8 mm dia in stirrups, spacers and binders as in columns and beams etc. as specified and directed by Engr-in-Charge.

M&L for use & waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions, Square, rectangular or polygonal for rough finished flat surface of concrete complete all as specified and as directed by Engr-in-Charge.

M&L for cement concrete Type B1(1:2:4) using 20mm graded aggregate in lintels upto 1.5m span and over complete as specified and directed.

M&L for Hardcore of broken stone or boulders of guage nexc 63mm, deposited, spread & levelled in layers n exc. 15 cm thick,watered and rolled/rammed to a true surface

M&L for laying 100mm thk PCC, type B- 2, 1:2:4 using 40mm graded aggregate

M&L for screed bed or bedding layer of mortar 15 mm thick for laying floor finishes in CM 1:4

M&L rendering 15 mm thick in cm 1:4 on fair facesof concrete or brick surfaces as in wall finishes even and smooth w/o using extra cement ,complete all as specified and directed.

M&L rendering 15 mm thick in cm 1:4 on other than fair faces of concrete or brick surfaces as in wall finishes even and smooth w/o using extra cement ,complete all as specified and directed.

M&L rendering 5 mm thick in cm 1:4 on ceilingsof concrete or brick surfaces as in wall finishes even and smooth w/o using extra cement ,complete all as specified and directed.

M&L for Glazed ceramic coloured tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match

M&L for 7mm thick non skid coloured ceramic tiles (area of each tile exc 0.06 and nexc 0.11sqm) etc set and jointed in neat cement slurry and pointed with white or coloured cement mixed with pigments and 15mm thick screed bed or bedding layer in cement mortar 1:6 for laying floor finishes.

M&L for 75mm thick PCC 1:3:6 type C1 (using 20mm graded stone aggregate) as in plinth protection and finished concrete surface even and smooth without using extra cement including making proper joints with bitumen mastic with sand as per specification at an interval of 3m and change of direction complete all as specified and as directed by Engr-in-Charge.

M&L for two coats distember over a coat of primer on plastered surface of any description,including preparation of new plastered surface complete all as specified and as directed.

M&L for two coats of cement based paint over a coat of alkali resistance primer on new plastered surface of any description,including preparation of new plastered surface complete all as specified and as directed.

M&L for two coats distember over a coat of primer on ceiling of any description,including preparation of new plastered surface complete all as specified and as directed.

M&L for plain sheet glass 4.80mm thick ordinalry quality and glazing with oil putty or wooden beads in square or fixed with aluminium section including rubber beads not exc 0.50 sqm in each pane complete all as specified and as directed by Engr-in-Charge.

S&F for 2nd Class softwood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed

S & F 35mm thick 2nd class softwood, plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately).

S&F Factory made with particle board core single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: stainless steel butt hinges and necessary S S screws shall be paid separately)

M&L for preparation of new wooden surfaces of any description not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified.

S&F Extruded aluminium alloy handles 150mm long, fabricated type,anodised

S&F Butt hinges 100mm long , heavy weight, cold rolled mild steel, and fixed

S&F Aluminium anodised, barrel tower bolts 125mm long of extruded section and fixed

S&F 1000 ltrs Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified

S&F Polyproplyene random copolymer (PPR) (SDR 7.4 & SDR 11 UV ) 3 layer pipe with and including fitting such as bends elbow, tee short length socket union check nuts nipple etc (female and male as required complete of size 25mm outer dia suitable for hot/cold water supply line including testing complete all as per manufactures instructions and as directed by Engineer in charge.

S&F 75mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors

S&F 110 mm dia PVC (SWR) junction single, (Single T) equal or unequal

S&F 75 mm dia PVC (SWR) junction single, (Single T) equal or unequal

S&F viterous China squatting pan or Orissa patten 580 x 440 mm white with integral foot rest (excluding cistern) with front or back inlet ant pattern as in repairs incl bedding with p.c.c type B-I 1:2:4 , using 20 mm graded crushed stone aggregate.

S & F Vitreous china wash down water closet (Pedestal), white (EWC) including Plastic seat of same colour of WC, closed patttern with flat bottom, and cover and Mild steel chromium plated hinging device complete excluding fixing bolts, flushing cistern and flush pipe) complete all as specified and directed by Engr-in-Charge

S&F 10 ltrs capacity incl PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets including flush pipe of polyethylene of low or high density or PVC. 32 mm dia, for low level cistern, complete all as specified and directed by Engr-in-Charge

S&F Vitreous China wash basin, white, flat back, size 580x450MM (for Hospilal use) excluding taps, waste, chain and plug and porcelain stopper but including brackets

S&F Chrominum plated Bib taps 15 mm dia , cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed

S&F fancy type Stop valves 15mm dia , cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed

S&F 15mm bore, Pillar taps fancy type, cast copper alloy, with capstan heads, chromium plated,screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed

S&F health faucet (ABS Body) mild steel shromium plated suitable for 15 mm dia with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.

S & F Toilet paper holder with flat recessed type stainless steel complete all as specified and directed

S&F PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement

S&F Towel Rail 600mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats. (Minimum weight 190gms)

M&L 32mm dia Waste fittings, brass chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed

S&F 750 mm long, 32/40 mm dia, PVC plain waste pipe for sinks/ wash hand basins complete all as specified and directed

S& F Grating doom 125 mm dia with waste hole of PTMT. (Minimum weight 40gms)

S&F 75 mm PVC (SWR) multi floor trap with grating including jointing with solvent cement

S&F PVC connections 15mm size with PTMT nuts of length 600mm

S&F PP-R Gate valves 25 mm dia(brass insert) as per requirement of the site

S&F PP-R Ball valves 25 mm dia (brass insert) as per requirement of the site

S&F Nipple suitable for HDPE water tank. (Minimum weight 15 mm-38gms/20mm- 45gms /25mm- 65gms)

S&F Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) (back or corner wall type),complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive offixing supply pipe to flushing cistern, trap and waste pipe)

S&F 75mm bore PVC (SWR) pipe bends any radius

S&F 110mm bore PVC (SWR) pipe bends any radius

M&L for soakage well of 3 mtr internal dia at top and min 1.80 mtr dia at bottom having min 3.0 mtr height of 380 mm thick random rubble uncoursed stone masonary wall in CM 1:6 with 150 mm thick PCC 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) below stone masonary at bottom and RCC slab using Design mix M-25 with reinforcement 10 mm dia bars @ 150 mm c/c bothways cranked at 1/4 th of the span including arrangenment for manhole poening and manhole cover, inlet for 100/150 mm dia pipe and rest all as specified as per Drg No CESZ/TD-1078/2011 sheet 1/1 Note :- The rate includes excavation in hard/dense soil and construction of soakage well as per drawing connection of inlet pipe, 100 mm dia PVC vent pipe with cowl, returning, filling and removing of surplus soil to a distance exc 50 mtr but not exc 100 mtr from site for any issues regarding drawing decision of Engr-in-Charge shall be final during execution.

M& L, Plain cement concrete , type B-1, 1:2:4 (using 20 mm graded crushed stone aggregates) as in coping, cills, steps, in lintels upto 1.5m clear span and similar other works like bands, plinth courses, lacing courses, bed plates, water troughs and the like incl weathring, slightly rounded or chamfered angles and throating, incl necessary form work, complete all as specified and directed by Engr-in-Charge. (Note - Reinforcement if provided, shall be measured and paid separately under relevent items).

M&L for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams,sides and soffits (if any) of foundation and plinth beams, lintel beam ; and similar work; vertical or to batter

S&F Structural steel works as in tubular roof trusses, purlins, Rafter, vertical posts, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, tubular pipe, channel or flat sections) including distance pieces, cleats , riveting incl bending and welding, conforming to Fe – 410W Gde E -- 250 quality A complete all spd and as directed.

M&L for preparation of new or previously untreated steel surfaces of any description over 10cm in width or girth, not other wise decribed and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

S&F Pre-painted galvalume aluminium zince coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

M&L rendering 15mm thick in cm 1:6 other than fair face as in wall finishes even and smooth w/o using extra cement ,complete all as specified and directed.

M&L cement concrete Grade Type B 0,1:2:4 (12.5mm graded aggregate) in Damp proof course all as specified and as directed.

M&L Reinforced Cement concrete designl mix type M-25 (using 20 mm graded crushed stone aggregate) in foundations, inclucing rafts, footings, foundations beams : plinth beams: bases for column, etc " basement slabs , under reamed piles ad mass concrete complete all as specified and directed by Engr-in-charge.

S&F anodised aluminium snap grid of size 605 x 605mm , frame work of false ceiling including hangers 4mm dia G.I (up to 1200mm length ) adjusting level fixed to roof slabs by means of ceilling cleats made out of GI flat 40 x 3mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long complete all as specified and directed by Engr -in-charge .

M&L providing and fixing Gypsum board 6mm thick and 600x600mm in size in ceiling fixed with screw or with staples on snap grid as per manufactures instructions, complete all as specified and directed by Engr-in-charge.

M&L for Cement concrete type B-2,1:4:8 (40mm graded aggreate) 75 mm thick as in sub -floors ,sub- bases ,floors and pavings,etc.

M & L 25mm thick Cement concrete type B-1, 1:2:4 (20mm graded aggregate).

M&L Non-Skid ceramic Coloured Tiles 7 to 8mm thick(squre/rectanglar) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors over 20 mm screed bed or bedding layers in cement mortar 1:6 Set and Jointed in neat Cement Slurry and Pointed in Colour Cement to match, complete all as specified and as directed.

M&L for (350mmx250mmx7mm/450mmx350mmx 7mm thick ) coloured ceramic tiles set and jointed in neat cement slurry and pointed with white or coloured cement mixed with pigments over 10mm thick rendering in CM 1:4.

S&F 2nd class hard wood plain, solid, straight chowkets and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete all as directed by Engr-in-Charge.

S&F for 35mm thick 2nd class hard wood plain framed paneled shutters (two panels) with panels with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces and fixed to chowkats , complete all as directed by Engr-in-charge.

S&F 30mm thick 2nd Class hard wood Glazed and skelton shutter, open rebated and prapared to receive the glass, gauze, wire mess etc.(without sash bars) edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass etc. complete all as specified and as directed by the Engr-in-Charge.

S&F mild steel work as in hold fasts and similar work confirming to Fe-290 or Gd -E 165 complete.all as specified and as directed by the Engr-in-Charge.

Material & labour PCC (1:3:6) type C1 (using 20 mm graded stone aggregate) as in hold fast , bed block and like complete all as specified and as directed by the Engr-in-Charge.

S&F 150mm long aluminium anodized, barrel tower bolt of extruded section complete.

S&F 100mm long aluminium anodized, barrel tower bolt of extruded section complete.

S&F mild steel butt hinges, medium weight cold rolled 75mm size complete.

S&F 300mm long aluminium alloy, anodized, sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolt and sliding bolts of extruded section or cast aluminium alloy complete.

S&F 100mm size extruded aluminium alloy handles, fabricated type, anodized complete.

M&L for preperation of new plastered wall surface of any description and applying two coat of cement based paint over a coat of chalk whiting complete all as specified and as directed.

M&L for preperation of new plastered surface and apply two coats of oil bound distemper over a coat of primer Complete all as specified and directed by Engr-in-Charge

M&L Sheet glass, 5.5mm thick ordinary quality and glazing with aluminium beeds in square n exc 0.5 sq. m each pane complete all as specied and directed.

S&F 110mm dia bore PVC pipes single socketed having compressive strength 655 - 675 Kg/Cm2 , in any length with rubber ring joints , laid in trenches or in floors including PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) bed to drain including dismantling of cast iron/ PVC or reinforced concrete pipes jointed in cement mortar and taking out of trenches if reqd of any dia complete all as specified and directed by Engr-in-Charge.

S&F PVC (SWR) vent cowl 110mm.

S & F Vitreous China Urinal, Half stall type, white (excluding flushing cistern, flush pipe and waste pipe) Cera or equivalent make of Jaquar/Hindware or equivalent approved make.

S&F Grating doom 125 mm dia with waste hole of PTMT. (Minimum weight 40gms) complete all as specified and directed.

S&F 40mm dia waste cuppling of PTMT (Half or ful threaded) 60 grams.

S&F chromium plated soap dish any type fixed to plugs with brass screws.

S&F PVC connection 15mm bore with ptmt nuts of length 450mm.

S&F Polyproplyene random copolymer (PPR) (SDR 7.4 & SDR 11 UV ) 3 layer pipe with and including fitting such as bends elbow, tee short length socket union check nuts nipple etc (female and male as required complete of size 32mm outer dia suitable for hot/cold water supply line including testing complete all as per manufactures instructions and as directed by Engineer in charge.

S&F 25mm bore brass valve high pressure with polythene float and fly nuts complete screwed for iron pipe or brass ferrule.

M&L for Chequred cement concrete tiles 30cm X 30cm X 20mm thick, set ,pointed & jointed in neat cement slurry in floors polished with grey cement & pigments layed over 20mm thick cement screed base (1:6) and all as directed by Engr-in - charge.

M&L Forming Contraction (Dummy) joints 50 mm deep x 10mm wide for plinth protection & similar work , filled with sealing compound Grade 'A' in plinth protection.

Excavating in post holes hard/dense soil (of similar holes) each n. Exc. 0.50 cum getting out, returning filling in and ramming earth or broken rubble mixed with earth around, in layers not exc 25cm, watering and removing surplus soil to a distance n. Exc. 50m and making good surface complete all as specified and directed by Engr-in-Charge

M & L Cement concrete 1:2:4 type B0 (using 12.5 mm graded stone aggregate) in foundations, filling complete all as specified and directed by Engr-in-Charge

S & F rolled sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates conforming to FE-410 - W(grade E-250) quality 'A' complete all as specified and directed by Engr-in-Charge

M & L for roof trusses framed, purlins, crane gantries rails and fasternings and heavy bracket framing (beam, tee, angle, channel or flat sections ) including distance pieces, cleats etc conforming to FE-410 - W(grade E-250) quality 'A' complete all as specified and directed by Engr-in-Charge

Mild steel screw boltsl of ength of bolt exc 5cm but n exc 10cm long, diameter of neck 11 to 15mm (machine made) with hexagonal or square heads,at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 5cm long complete all as specified and directed by Engr-in-Charge

M&L for 100 mm thick PCC 1:4:8 type D-2, using 40mm graded crushed stone aggregate as in sub base complete all as specified and directed by Engr-in-Charge

M&L for machine pressed / vibro mechanically floated precast concrete interlocking cement paver block ISI marked, any shape and size conforming to IS 15658-2006 of 60mm thickness, M-35 Grade, with topping of grey cement and pigment, complete all as specified and directed by Engr-in-Charge

M&L Sand filling under floors or in foundations including watering and consolidation, complete all as specified and directed.

S & F, Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled forfixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete and conforming to Fe 410-W Gde E-250 quality 'A',complete all as specified and directed by Engr-in-Charge

Supply and install testing and commissioning hi wall split units indoor/ outdoor unit (Hahing duty copper coil), single phase with complete accessories with cordless remote control unit and with cooling and heating function of capacity 2 Ton, 5 star incl suitable length of copper pipes for connection complete all as specefied and directed. Note :- (i) AC shall be fully functional for hot air supply Iambient indoor temprature) at minus 30 degree invironment temprature in winter season. (ii) AC shall be fully functional for cool air supply Iambient indoor temprature) at 35 degree or more invironment temprature in summer season of capacity complete all as directed and specified.

S&F Havells DBOXX Protected Socket AC Box with SP MCB switch socket combination 25 Amp flush type universal with plug top complete all as directed and specified.

M & L for submain wiring alongwith earth wire with the following sizes of FRLSH PVC insulated copper conductor, single core cable in surface/recessed as required in PVC casing Caping wire size 2x4.0 sq. mm + 1x 4 sq. mm earth wire complete all as specified and directed.

Supply and fix air conditioner iron stand suitable for 2 ton AC with anchor fastner complete all as specified and directed.

M & L 50 mm thick PCC 1:2:4 type B-0 using 12.5 mm graded aggregate as in floor complette all as specified and directed by Engr-in-Charge.

M&L for 10mm thick rendering on fair faces of brick works finished even and smooth without using extra cement in cement mortar 1:6 Complete all as specified and directed by Engr-in-Charge

S & F Vitreous china wash basin white flat back size 550 x 400 mm including including CI brackets of irosn 65 x 65 x 6mm embeded in PCC block with PCC 1:2:4 type B-1 & CP grating with holes fixed complete all as specified and directed by Engr-in-Charge

S&F Vitreous China Urinal full stall type white (excluding flushing cistern flush pipe and wast pipe) Vitreous China Urinals bowl type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement fixing automatic flushing cistern with brackets, flush pipe grating and union for discharge pipe, urinal spreader etc complete all as specified and directed by Engr-in-Charge

S&F 20 mm bore bib taps long or short body fancey type chromium plated with capstan head chromium plated screwed down screwed for iron pipe or brass ferrule. (Minm wt 350 Gms) complete all as specified and directed by Engr-in-Charge

S&F Towel rail with accessories set (fixed in repair )Cat No, CAN -1121N of make jaquar complete all as specified and as directed complete all as specified and directed by Engr-in-Charge

S&F PVC waste pipe 32mm bore with cup and washers complete on new or old locations complete all as specified and directed by Engr-in-Charge

S&F 20mm bore brass valve high pressure with polythene float and fly nuts complete screwed for iron pipe or brass ferrule complete all as specified and directed by Engr-in-Charge

S & F CP floor gratings 125 mm dia all complete all as specified and directed by Engr-in-Charge

S&F for 30 mm thick 2nd class soft wood plain framed paneled shutters (any number of panels) with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers, Supply and fixed to chowkats complete all as specified and directed by Engr-in-Charge

S&F framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles as necessary, gusset plates, cleats, MS Flat, MS plate, rivetting etc n.exc 10 kg each brackets, conforming to FE 290 Gde E-165 complete all as specified and directed by Engr-in-Charge

S & F gypsum ceiling board 8 to 9 mm thick in 600 x 600 mm pannel designer ceiling tiles laminated with white colour PVC film on the face side and a metalised polyster film on the back side, conforming to IS-14862 type B category three including suspended false ceiling using E-grid suspended ceiling grid system of grid size 600x600mm with GI frame work of main runner 38 x 24mm sheet thickness 0.4mm, cross Tee 28 x 24mm sheet thickness 0.3mm and wall angle 24 x 24mm to be placed in the grid suspended by 4mm GI wire hanger to be fixed as per site requirement including taking down of old false ceiling complete all as specified and directed by Engr-in-Charge

M&L for Cement concerete bed to drain pipes incl packing under haunching against the sides of pipes after they are laid tested in 1:4: 8 type D-2 using 40 mm graded stone aggregate of bore of pipe upto 200mm complete all as specified and directed by Engr-in-Charge

S&F 200mm dia bore (inner dia) double wall corrugated HDPE pipe (SN-8) in any length including all fitting and jointing with eastomeric rubber link and cuppler/other jointing material laid in trenches are in floors complete all as specified and directed by Engr-in-Charge

M&L RCC type B1 1:2:4, nominak mix (20 mm grade aggregate ) in Slabs supported on walls ,beams and columns,in floors, roofs,landings, balconies, canopies,deck slabs and in shelves and the like, complete all as specified and as directed.

Rendering 15mm thick cement plaster on brick masonry surfaces in cement mortar 1:4 finished to even & smooth surfaces (without using extra cement) including mixing of integral water proofing compound in the proportion as mentioned in manufacturer's instructions, complete all as specified and directed by Engr-in-Charge

S & F of 75 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls complete all as specified and directed by Engr-in-Charge

S&f 110 mm bore PVC (SWR) pipe single socketed , in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed by Engr-in-Charge

S & F 75MM PVC Nahani trap, setting and jointing with solvent cement and fixed in Cement concrete type B-1 (1:2:4) complete all as specified and directed by Engr-in-Charge

M&Lproviding pre-cast cement concrete(20mm graded crushed stone aggregate) 1:3:6 type C-1 as in block or slabs 10cm thick ( with plain or interlocking joints as directed) and setting in cement mortar 1:6, complete all as specified and as directed.

M&L PCC 1:3:6 type C-2 (using 20mm graded stone agg) 75mm thick sub base of floor etc, complete all as specified and as directed.

M&L sheet glass 4mm thick ordinalry quality and glazing with aluminium beeds in square not exc 0.50 sqm in each pane complete all as specified and as directed

S & F Galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples, complete all as specified and as directed.

Supply only integral liquid water proofing compound complete all as specified and directed. Make : Pidilite/Sika

S&F CI floor trap with grating including jointing to waste pipe fixed in cement concrete type B-1 1:2:4, 100mm dia, complete all as specified and as directed.

S&F PVC (SWR) vent cowl 75mm , complete all as specified and as directed.

Stack clamp out of 50mm x5mm flat iron stays including bolt and nuts and securing ends of stays to walls or roof for 100mm bore piece.

S&F sand cast iron 'P' or S trap 100mm bore, complete all as specified and as directed.

S & F Vitreous China wash basin Fency type pedestal pattern , white, flat back, size 550 x 400mm including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe, complete all as specified and as directed.

S&F 32mm dia waste cuppling of PTMT (Half or ful threaded) 45 grams, complete all as specified and as directed.

S&F 20mm bore stop cock chromium plated screw down under high pressure with crutch or butter fly handle screwed both ends for iron pipe or brass ferrule, complete all as specified and as directed.

S&F 20mm bore chromium plated angular stop cock with wall flange, complete all as specified and as directed.

S&F 25mm bore stop valves chromium plated screw down under high pressure with crutch or butter fly handle screwed both ends for iron pipe or brass ferrule, complete all as specified and as directed.

S&F 25mm bore brass valve high pressure with polythene float and fly nuts complete screwed for iron pipe or brass ferrule, complete all as specified and as directed.

S&F Rotational moulded polye­thylene water storage tanks (cylindrical vertical with closed top) 500 litres capacity , hoisted and fixed in position all as specified in SSR Part I, complete all as specified and as directed.

Excavation over area in Hard/dense soil n exc 1.5m deep and getting out in hard/dense soil, complete all as specified and as directed.

Excavation over area in Hard/dense soil exc 1.5m but n exc 3.0m deep and getting out all as specified.

M&L Walling of random rubble uncoursed stone masonry, uncoursed well bonded laid dry in retaining wall abutment and similar work, complete all as specified and as directed.

M&L form work to soffits of suspended flat sabs such as roof slabs ,floor slabs,landings and similar works (smooth finished flat surface of cncrete) not exceding 200mm thick (Horrizontal or sloping), complete all as specified and as directed.

M&L form work to fair finshed edges of concreat flats, treads breaks in floors, window cills, concrete failings, openings in concrete walls, floor and roofs n.exe 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20 cm wide, complete all as specified and as directed.

M&L for precast cement concrete Type B1, 1:2:4 (20mm graded aggregate) in landings, cover slabs (for manholes etc), chullah hoods, chhajja, water troughs, shelves and similar articles with plain faces, setting in CM 1:6, complete all as specified and as directed.

M & L Concrete bed in 1:3:6 type C2 (40mm graded stone agg) to drain pipe of bore 150 mm including packing under ,and haunching against the sides of pipe after they laid and tested;

M&L for point wiring with copper conductor cable Multistrand, single core 1.5 Sqmm size for one light point or bell point /Ex: fan Point controlled by one switch including one run of 1.5 Sqmm multistrand PVC copper conductor cable for earth continuity in and including PVC casing and capping of approved size and quality fixed on walls/ceiling including rectangular PVC/Metal flush box board heavy duty type for mounting switches /sockets etc complete all as specified and directed by Engr in Charge.

All as per item No 158 above but One 3 pin switch socket combination 5 Amp on independent board complete all as specified and directed.

All as per item No 158 above but One 3 pin socket out let 5 Amp on the same board with other switches complete all as specified and directed.

All as per item No 158 above but for power point 3 pin switch socket 15 Amp with PVC copper conductor cable multistrand unsheathed 2.5 Sqmm on independent board incl one run 1.5 Sqmm multistrand PVC copper conductor cable for earth continuity in and including PVC casing and capping fixed on wall incl including PVC /Metal flush box board complete all as specified and as directed by Engr in Charge.

All as per item No 158 above but for power point 3 pin switch socket 15 Amp with PVC copper conductor cable multistrand unsheathed 4.0 Sqmm on independent board incl one run 1.5 Sqmm multistrand PVC copper conductor cable for earth continuity in and including PVC casing and capping fixed on wall incl including PVC /Metal flush box board complete all as specified and as directed by Engr in Charge.

S&F switch piano flush type one way single pole 5/6 Amp 240 volts complete all as specified and directed by Engr in Charge.

Supply and fix of switch Socket combination flush type 3/5 pin 5/6 Amps 230 volts complete all as directed.

Supply and fix of Socket outlet 3 pin, 5A, flush type complete all as directed.

S&F switch socket combination 2 in 1, 3 pin 5 & 15 Amp flush type complete all as specified and directed by Engr in Charge.

S & F decorative durable LED batten fitting of 18/20W , 4 feet long with decorative and caps, powder coated CRCA decorative for LED tube of any capacity, 4 feet long (white colour) tube having driver ,connector block etc complete with all accessories prewired and connecting electrically to ceiling rose using PVC insulated and overall sheathed flexible copper conductor cable of size 0.75 Sqmm 3 core all as required at site or directed by Engr in Charge.

S&F LED Mirror light fitting of 9/10 W and type 230 volts box type , with standard specification etc complete withh all accessories pre wired twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed by Engr in Charge.

Supply and replacement of Ceiling rose, surface Bakelite three terminals complete all as directed.

Supply and Fix 7 watt LED bulb all as required at site or directed by Engr-In-Charge. Make:- Havells or Eqvt in Philips/Bajaj/Wipro/crompton

S&F Lamp Holder PVC/Polycorbonate type with back plate suitable for batten fitting

Supply and fixing Air circulator made of sturdy Engineering plastic complete with louvers, shutter, voltage 230 volt, 50 Htz RPM 1200, copper winding of sweep 250 mm complete all as specified and directed by Engr-in-Charge.

S&F sheet metal enclosure SPN for DBs with 200 Amps bus bar of 8 way 240 volts with blank plate complete with metal double door all as directed by Engr-in-Charge.

S&F MCB SPN 6 to 32 Amps 240 Volts. Make : Iegrand /L&T

S&F MCB single phase (SP), 6 to 32 Amps 240 Volts. Make : Iegrand /L&T

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete.

Supply, laying and testing cable XLPE Insulated ,armoured heavy duty electric cable electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10.0 sq mm 2 core

Excavation in trenches, not exceeding 1.5 meter wide and not exceeding 1.5 meter in depth for foundation of poles, stays or for taking out/laying of cables and getting out in soft/loose soil complete all as specified and directed by Engr-in-Charge.

M&L for Sand cushioning to underground cables 8 cm below the cable before laying & 15 cm above the cable after laying, complete all as specified in clause 19.75 of SSR Par-I, complete all as specified. Note : Punned thickness of 18 CM will be measured and paid for.

Replacement of factory made, machine pressed, unreinforced, pre-cast concrete cable cover class LV type-I flate size 250 x 150x40mm , complete all as specified and directed by Engr in Charge.

M & L 40 mm GI Pipe light grade for cable protecton in road crossing and making good surface road to filling with PCC complete all as specified and directed by Engr in Charge.

M & L for Earthing complete with galvanised steel earth plate electrode 60×60cm.× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion .

Supply and fix ing of MCB SPN 63 Amp 240 Volts AC ISI marked all as specified and directed by Engr-in-Charge.

Supply and fix in exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers

Supply, install, testing complete water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 Litre, BEE 5 star rated complete with all accessories such as safety valve, thermostate, NRV, connection pipes etc

Supply and laying of XLPE insulated, armoured, haeavy duty electric cables (heavy duty) with stranded aluminium conductor rating 1100 volts grade of size 35 Sqmm 2.0 core laid in trences or passing through pipes.ducts or fixed to walls/poles completer all as specified.

Supply and fix in replacement of sheet metal enclosure for DBs double door when MCB's to be used single pole & neutral 240 Volts 4 Ways all as specified and directed by Engr-in-Charge.

S & F LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size.

Supply and fix LED down light ( round, Coll white ) of capacity 15 Watt, motion sensing based with 4.5 mtrs radius, 215 Volts complete all as specified annd directed.

Deduct Schedule of Credit of Rs (-) NIL (Minus) as listed in Schedule 'A' (Contd). Contract Sum shall be arrived after deducting the credit amount. Note :- Tenderers will not quote against this item being a firm amount.

Mehar Enterprises (BID ID -3487964)