NIT-09/BCDH-I CivilworksDoorSancharBhavanHYD

Amount

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.

For thickness of tiles 10 mm to 25 mm

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

1:1½:3 (1 Cement: 1½ coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Providing, hoisting and fixing up to floor five level precast reinforced cement concrete in small lintels not exceeding 1.5m clear span up to floor five level, including the cost of required centering, shuttering but , excluding the cost of reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20mm nominal size).

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete up to plinth level.

Thermo-Mechanically Treated bars of grade Fe-500 D or more.

Brick work with common burnt clay modular bricks of class designation 35 in foundation and plinth in:

Cement mortar 1:4 (1 cement : 4 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 3.5 in superstructure above plinth level up to floor V level.

Cement mortar 1:4 (1 cement :4 coarse sand)

Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete :

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm) with necessary accessories and screws etc. complete.

Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete :

Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete :

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete

Providing and laying Ceramic glazed floor tiles of size 300x300 mm(thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement :4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigment etc.,., complete.

12 mm cement plaster of mix :

1:6 (1 cement: 6 fine sand)

15 mm cement plaster on the rough side of single or half brick wall of mix :

1:4 (1 cement: 4 fine sand)

Distempering with 1st quality acrylic distemper (ready mixed) of approved manufacturer, of required shade and colour complete, as per manufacturer's specification.

Two or more coats on new work.

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface :

Water thinnable cement primer.

Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour.

Two coats.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :

One or more coats on old work.

Finishing walls with Acrylic Smooth exterior paint of required shade :

Old work (Two or more coat applied @ 1.67 ltr/ 10 sqm) on existing cement paint surface).

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq. meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground within 50 metres lead :

With cement mortar 1:4 (1 cement : 4 fine sand).

Renewal of old putty of glass panes (length) .

Renewing glass panes, with putty and nails wherever necessary including racking out the old putty:

Float glass panes of thickness 4 mm.

Taking out existing wooden door shutter, repair by cutting, painting etc. and refixing of repaired door shutters to existing door frames, including replacement of hinges with screws, etc. as required, all complete as per the direction of the Engineer-in-charge.

Providing and fixing white vitreous china pedestal type (European type/ wash down type) water closet pan.

Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete.

10 litre capacity - White

Providing and fixing solid plastic seat with lid for pedestal type W.C. pan complete :

White solid plastic seat with lid

Providing and fixing white vitreous china wash basin including making all connections but excluding the cost of fittings :

Flat back wash basin of size 550x400 mm.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

Flexible pipe

32 mm dia

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :

Rectangular shape 453x357 mm

Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour.

Waste coupling 31 mm dia of 79 mm length and 62 mm breadth weighing not less than 45 gms.

Providing and fixing kitchen sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P. brass waste complete, including painting the fittings and brackets, cutting and making good the walls wherever required:

White glazed fire clay kitchen sink of size 600x450x 250 mm

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. : Internal work - Exposed on wall

20 mm nominal outer dia. Pipes.

25 mm nominal outer dia .Pipes.

40 mm nominal outer dia. Pipes.

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete :

25 to 40 mm nominal bore

Providing and fixing uplasticised PVC connection pipe with brass unions :

45 cm length

15 mm nominal bore

Providing and fixing PTMT bib cock of approved quality and colour.

15mm nominal bore, 86 mm long. Weighing not less than 88 gms.

Providing and fixing PTMT stop cock of approved quality and colour.

15 mm nominal bore, 86 mm long. Weighing not less than 88 gms.

Providing and fixing PTMT grating of approved quality and colour.

Circular type.

100 mm nominal dia.

Providing and fixing PTMT angle stop cock 15 mm nominal bore. Weighing not less than 85 gms.

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg., for doors, including cost of cutting floors ,embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge.

With stainless steel cover plate minimum 1.25 mm thickness.

Cleaning of under ground sump, Over Head R.C.C. Tank (independent staging) including disposal of silt and rubbish, all as per direction of Engineer-in-Charge. The cleaning shall consist following operations:-

(i) Tank shall be emptied of water by pumping & sides & bottom shall be cleaned of silt and other deposits.

(ii) Entire surface area of the sump/tank shall then be scrubbed thoroughly with wire brush etc. and pressure washed thoroughly with water.

(iii) Chlorination of internal wall surface by liquid chlorine.

(iv) The treated surface shall be dried using air jetting and all loose particles shall be removed from the surface.

(v) Finally the surface shall be treated with ultraviolet radiation etc. as per direction of Engineer-in-Charge.

Providing and fixing M.S Brackets for wash basin/Sink or required size embedded in cement concrete including cutting and making good walls etc., all complete as per the directions of Engineer-in-Charge. Pair of brackets is measured for payment.

Repairs to pvc flush tank with replacing the lever or handle wherever required including changing the syphon set including cleaning the dirt, scales, adjustment in the flush mechanism etc, complete. Repairing as above for each tank is measured for payment.

Repairs to PVC flush tank with replacing the lever or handle wherever required but without changing the syphon set including cleaning the dirt, scales, adjustment in the flush mechanism etc, complete. Repairing as above for each tank is measured for payment.

Removing unserviceable G.I pipe lines of all diameters attending necessary repairs blockages/chokages/scales by rodding/ hammering etc complete at all heights the rate includes removing the nails,clamps and re-fixing the same after attending necessary repairs complete etc., as directed by Engineer-in-charge.

Providing and fixing Brass MABT/FABT including cutting and threading the GI pipe Line and connecting to CPVC line wherever required etc. complete

a)20 mm nominal bore

b)25 mm nominal bore

c)40 mm nominal bore

Cleaning of blocked Nahani trap / floor trap for removal of blockages including removing the silt , slush,, waste etc ensuring smooth flow etc., and applying white cement on the flooring around the trap and fixing the grating with white cement and disposal of all unwanted material to the approved muncipal dumping yard and wherever required to arrest the leakage from tile joints all complete etc.,and as per direction of Engineer in charge

Clearing chowkage of exisitng gully trap. Cost includes all labour and material required for removing the silt, slush, waste etc. and rodding the sewer line from gully trap to manhole to clear the blockage, chokeage etc for proper functioning of sewer lines (The payment shall be made for removal of blockage in between gully trap to manhole as one job with all above operations.) disposal of all unwanted material to the approved muncipal dumping yard etc all complete and as per direction of Engineer in charge

Removing G.I.Pipes of all diameters after attending necessary repairs and removal of blockages/chockages/scales by rodding/ hammering etc complete at all heights the rate includes incidental required such as nails ,clamps etc.required for fixing the GI pipes all complete.. as directed by Engineer-in-charge.

Credit for disposal of old recovered material

Bibcock/Stopcock/Pillarcock of all sizes.

Providing and fixing clamps to existing GI/CPVC pipeline laid on walls of diametre 15mm to 40 mm with necessary screws, nails including wooden plug etc., at all levels and as per the directions of Engineer-in-charge.Rate includes removing and refixing of GI/CPVC pipe lines wherever required.

Providing and fixing gun metal ball valve with SS ball & MS lever including cutting and threading the GI Line wherever required etc. complete

a)20 mm nominal bore

b)25 mm nominal bore

c)40 mm nominal bore

Providing and fixing CPVC ball valve in CPVC pipe line including cutting and jointing with CPVC solvent cement etc complete.

a)20 mm nominal bore

b)25 mm nominal bore

c)40 mm nominal bore

Providing and fixing CPVC union in CPVC pipe line including cutting and jointing with CPVC solvent cement etc complete.

a)20 mm nominal bore

b)25 mm nominal bore

c)40 mm nominal bore

Providing UPVC SWR soil waste and vent pipes by cutting, removing, replacing with working pressure 6kgf/sq.cm conforming to IS : 13592 Type B including jointing with 'T' shaped seal/rubber ring conforming to IS : 5382 and with solvent cement or rubber lubricant as the case may be with pipes of outer dia (concealed pipe joints to be jointed with rubber ring and solvent cement and exposed joints to be jointed with rubber ring and rubber lubricant. (i)Single socketed pipe(couplings,other accesories will be paid seperately)

75mm diameter

Providing on wall face damaged unplasticised - PVC moulded fittings/ accessories with new fittings/accessories for unplasticised Rigid PVC SWR pipes conforming to IS : 13592 Type A including cutting,replacing,jointing with seal ring conforming to IS :5382 leaving 10 mm gap for thermal expansion.

Coupler

Plain bend of required degree

75mm bend

Tee with door

Door bend

Single Y with door of required degree

Providing and fixing unplasticised -PVC pipe clips of approved design for fixing of unplasticised - PVC pipes by means of 50x50x50mm hardwood plugs, screwed with M.S. screws of required length including cutting chases in brick work, fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall with rich cement plaster etc. complete.

Carting out of building rubbish / malba / similar unserviceable, dismantled, excavated or waste materials by mechanical means,through private carrier including lifting, loading, transporting, unloading to municipal dumping ground beyond 50 m initial lead,or in any other compound as decided by the Engineer-in-charge, for all leads including all lifts involved.

Cleaning of sewer lines, manholes etc.,at all depths. cost includes all labour for removing the sludge, silt, slush, waste etc., from the manholes and rodding the sewer lines by mobile sewer roding equipment from manhole to manhole to clear the blockage, including chokes in gully traps etc.and disposing the waste outside the compound etc., complete.as per directions of Engineer-in-charge) Sewer line upto 150mm dia. (Rate for sewer line between two no.manholes to be measured for payment ) and disposal of all unwanted material to the approved muncipal dumping yard etc all complete and as per direction of Engineer in charge (Nothing extra paid).

Providing and fixing PTMT health faucet with PVC pipe with holder of 15mm nominal bore nozzle jet and handle of approved quality and make adjacent to WC as per the directions of engineer in charge. (Nothing extra paid)., as directed by the Engineer-in-charge.

Providing and fixing C.P. brass two way (2in1) bib/ stop cock Parryware Claret (T4642A1) make or approved equivalent to be fixed by removing old bibcocks including making necessary adjustments. All complete as per directions of Engg-in-Charge. The rate is all inclusive of all operations nothing extra be paid on any account. a)15 mm nominal bore

Providing and fixing C.P.Brass bib cock of Parryware Claret (T4604A1) make or approved equivalent to be fixed by removing old bibcocks including making necessary adjustments. All complete as per directions of Engg-in-Charge. The rate is all inclusive of all operations nothing extra be paid on any account. a) 15mm dia nominal bore

Providing and fixing C.P.Brass Pillar cock of Parryware Claret make (T4601A1) or approved equivalent to be fixed by removing old pillar cocks including making necessary adjustments. All complete as per directions of Engg-in-Charge. The rate is all inclusive of all operations nothing extra shall be paid on any account. a)15 mm nominal bore

Dismantling existing aluminium partitions, doors and other frames including proper numbering, loading and unloading,stacking and placing at the required place in the building as directed by the Engineer-in-charge . (Area of partition is measured for payment)

Fixing of aluminum partitions and doors after making required sections as per the drawing with available material of aluminum sections , particle board, glass panels, neoprene gasket and snap on beading including fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions at top, bottom and sides with required PVC/Neoprene felt etc, aluminum sections shall be smooth, rust free, straight , mitered and jointed mechanically wherever required all complete as per the architectural drawings and the directions of the Engineer-in-charge. (The available material as above on as is where is basis in stacked condition wiil be supplied by the departement at no cost. Finished area of partition is measured for payment)