Estimate for renovation of 03 Nos Parks near Mandir, H. No.- 935, 869 in Sector-22B, Ward No.- 3 under Zone-III, Gurugram.Recall

Providing and fixing Chain Swing - 2 seater ( Swing). Specifications Attached.

sea saw 4 seater 8 lx5 5 Hw X 15 high frame of ms pipe 2 x 12 guage sittibg planks is of pipes and handle seats 4 nos. molded frp material

Wave Slide: 9’.5 L x 5’H. Wave slide is of molded Fiberglass Reinforced Plastic (FRP) of 6mm thick and climbing ladder is of m.s pipe 1” x 12 gauge and m.s rectangular pipe

NS Item = Supply of RH Pipe 1` dia.

Providing and fixing of Gate valve for hydrant connection

M. S. Dustbin – 60 liter capacity made of MS Sheet of 16 mm gauge thick of approx.size 48”H with having 1no inlet and outlet with suitable enamel Paints, set having minimum weight of 30 kgs. Complete item with GST, Transportation, Installation with C.C and amp: labor at site.

Pull Chair:- Providing, and fixing of Pull pair of size 2500 X 800 X 2000 mm make of Green Gym or Equivalent fabricated with main post of 140 mm dia and 3.0 mm thick rest of the pipes are 40mm dia and 3.0 mm thick all pipes made up of hot roiled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc .primer paint to be applied at all welding points prior to finishing. Pedals shall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat to be` made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Officer-in-Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GULLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolts and once the concrete is set, fix theequipment on to it and cover nuts and bolts with the baseplate cover, all complete as per directions of Engineer in Charge.

Horse Rider Station:- Providing, and fixing of horse rider station of size 1000 x 600 x 1100 mm make of Green Gym or Equivalent fabricated with main post of 140 mm dia and 3.0 mm thick rest of the pipes are 40mm dia and 2.5 mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Alczo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Padals shall be made up Nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Engineer-in-Charge.Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and a. .royal of arge regari ing materia , s ape of equipment,colour on metal, seat and base cover plate and fixing of equipment etc.

Double Cross Walker/ Cross trainer double:- Providing, and fixing Double Cross Walker of size 1600 X 600 X 1600 mm make of Green Gym or Equivalent fabricated with main post of 140 mm dia and 3.0 mm thick rest of the G.I pipes are 40 mm dia and 2.5 mm thick all G.I pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All welding joints of G.I pipes are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Padals shall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company like SKF to be approved by Officer -in-Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of G.I pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength N425 and J shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of Engineer-in-Charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipment etc.` The rates are inclusive of all taxes like GST, Transportation, Installation in CC with 2 years defect liability period free of cost to full satisfaction of engineer in charge complete in all respect.

Leg Press: Providing designing and fixing of leg press of size 2000x550x1600 mm fabricated with main post of 114mm dia and 2.5mm thick and rest of the pipes 40mm dia and 2.5mm thick. All pipes made up of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nobel or equivalent of 80-120 micror thick

Twister:- Providing, and fixing Twister of size 1700 X 1300 X 1300 mm make of Green Gym or Equivalent fabricated with main post of 140 mm dia and 3.0 mm thick rest of the pipes are 40mm dia and 2.5 mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Padals shall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Officer-in-Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and ishapod welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of Officer -in-Charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of. equipment etc.`` `

Rowing machine: Providing designing and fixing rowing machine of size 1280x800x1150 mm fabricated with main past of 114 mm dia and 2.5mm thick and rest of the pipes 40mm dia and 2.5 mm thick. All pipes made up of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Handle bars are to be provided with high quality grip rubber Foothold shall be made up of nylon alloy with rounded edges to prevent any impact or injury and base cover to be made up from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic as 3mm colourful and UV resistant and environmental friendly. Bearing used shall be maintenance free duly oil sealed and self lubricated made by reputed company to be approved by Engineer in charge. Equipments to be fitted with inbuilt limiters to prevent unwanted movement. All open ends of pipe to be closed by GI/ LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M-25 and J shape welded bolts and once the concrete is set, fix the equipments on to it and cover with the base plate A.I complete as per direction and approval of engineer in charge regarding material shape of equipment colour on metal seat and base pedal and fixing of equipments etc (the cement concrete and excavation work shall be paid for separately).

Weld Mesh Panels with Fitting Accessories: (a). Weld Mesh Panels: i. Weld Mesh Panels manufactured with electrical resistance welded galvanized wires and subsequently powder coated as per specifications mentioned under. ii. Weld mesh panel for fence will meet the standards of IS 1566/ IS 4849 with the following key specifications apart from the other points in the governing specification: iii. Panel size: 2500 mm X 915 mm (W x H). Tolerance of plus / - 2 % Mesh Size: 50 mm X 150 mm (W X H). Tolerance of plus / - 2 mm iv. Weld Shear strength: Minimum 50 % of the breaking strength of the smallest wire (In this case the vertical wire) v. Mesh Wire: Galvanized MS wire Horizontal wire, Dia. 5.0 mm ( plus /- 0.05mm): Vertical wire, Dia. 5.0 mm( plus /-0.05mm) Tensile Strength of wire: Min 500 N/sq.mm: Specification for wire: IS 280 vi. Galvanizing of wire: 100 – 120 GSM as per IS 4826 (Measurement as per IS 6745) Uniformity of Coating: As per IS 2633: Adhesion test for coating: As per IS 2629 (1985) vii. Powder Coating: The galvanized panels are subsequently single powder coated after welding with a thickness of 60 to 80 microns. viii. Colour: RAL 6005 (Military Green): Coating Standard: EN 10245-1/ IS 13871 ix. Make : Akzonobal / Jotun. x. Other coating requirement: Powder coating should withstand 720 Hours of salt spray test as per ISO 12944, 1000 hrs of QUV-B Weatherometer Test, Adhesion test, Electrochemical Impedance Spectroscopy Test (Type Test Certificate for the coating standards from renowned Laboratories clearly indicating that the coating passes C3 or higher corrosion protections standard is to be submitted by the bidder along with technical bid). xi. Refer drawing of Panel, attached herewith. 25 mm pointed wires should be left on both sides (top and bottom only), V-band range: 100 mm to 110 mm xii. Qty: 400 Panels / KM (b) Square Clamp i. Type: Square Clamp with Side lock. ii. Specification: 65X35MM iii. Outer Diameter: 65 mm plus /- 1 % iv. Thickness: 3.00 mm plus /- 10% (Medium G

Percentage BoQ

BoQ_Ver3.0

Name of the Bidder/ Bidding Firm / Company :

PRICE SCHEDULE (This BOQ template must not be modified/replaced by the bidder and the same should be uploaded after filling the relevent columns, else the bidder is liable to be rejected for this tender. Bidders are allowed to enter the Bidder Name and Values only )

NUMBER #

Estimate for renovation of 03 Nos Parks near Mandir, H. No.- 935, 869 in Sector-22B, Ward No.- 3 under Zone-III, Gurugram.