Loss reduction works under RDSS in Nagaur Circle

Amount

(A) 33 KV for New 33 KV S/S and 33 KV Feeder Bifurcation/ interconnection etc

A-(1) 33 KV (Overhead) Line for New 33 KV S/S and 33 KV Feeder Bifurcation/ interconnection etc

Supply of PCC Poles 9 mtrs (400 KG)

Supply of 33 KV double pole line structure set (Galvanized) on 9mtrs PCC poles for cut point complete on existing poles in all respect as required made from M.S. channel 100x50 X6 mm, M.S. angle 75x75x6 ,M.S. Angle 50x50x6 mm and M.S. flat 50x10 mm & 50x6 mm [excluding cost of pole] weight(142.314 kgs.) Approx

Supply of 33 KV "V" Cross Arm (Angle) with Top Hamper and clamps made of MS Angle 75x75x6mm and 65x65x6 mm, MS Channel 100x50x6 mm , clamp MS Flat 50X10 mm (galvanized as per IS) (wt.= 22.849 Kgs.)approx

Supply of 33 KV porcelain Pin insulator with Pin

Supply of 45 KN. porcelain disc.insulators for 33 KV (each unit consisting of 3 disc insulators & one B&S Type hardware)

Supply of overhead steel cored aluminum ACSR DOG[100SqMM(6+7) /(4.72+1.57)] conductor complete in all respect as per latest specification and drawing.

Supply of PG clamps (For Dog) made of aluminum alloy as per IS:617-1994 (with latest amendments if any).

Supply of GI stay sets (Galvanized) complete with 20 mm dia ,2.4 mtrs long stay rod and 380 x380x4mm anchor plate including stay clamps 14mm turn buckle and GI stay wire size 7/8 SWG tightened through 33 KV stay insulator.

Stay Set

33 KV Strain/Guy Insulator

G. I. stay wire of 7/8 SWG (Galvanized) (1 set= 8.00 Kg)

Stay Clamps made of MS Flat 50x10 mm (1 Set = 2 Nos. Clamps) weight ( 3.65 Kgs.) Approx

Supply of 6 SWG GI Wire for continuous earthing of 33 KV Line hot dip (Galvanised) as per technical specification, approved drawings and scope of work.

Supply of earthing rod sets made with MS Rod (Galvanized ) 20 mm dia, 3 meter length along with G.I wire 8 SWG (approx. total length / weight, 17 meter/1.64 Kg. ) .

Supply of Danger plate of size 200 X 250 mm complete in all respect

Supply of 1.8 Meter Channel Bracket made of MS Channel 100x50x6 mm (Wt. 17.21 Kg with Clamp made of flat 50x10 mm(Wt. 1.83 kg) (Galvanized as per relevant IS)

Supply of M.S. Nuts & Bolts (Galvanized) of assorted size

A-(2) 33 KV (Underground) Line for New 33 KV S/S and 33 KV Feeder Bifurcation/ interconnection etc

Supply of 33 KV XLPE Insulated Armoured Cable size of 3CoreX300 Sq. mm.

Supply of 33 KV Cable (XLPE) termination / straight through joints ( Heat shrinkable type)

Cable End Kit 33 KV XLPE 3CX 300 SQ.MM H.S. ON OUTDOOR TYPE

Cable Jointing Kit 33 KV XLPE 3C X 300 SQ.MM H.S.Straight Through

Supply of earthing rod sets for 11 KV lines made with MS Rod (Galvanized) 20 mm dia, 3 meter length alongwith GI wire 8 SWG (approx.) total length / weight, 17 meter / 1.64 Kg.) as per latest specification and drawing adopted & approved by NIGAM.

Supply of Clamp of M S Flat 50x6 mm(2x0.501m, wt. 2.36 Kg. Approx)

Supply of Danger plate of size 200 X 250 mm complete in all respect

(B) New 33/11 kV sub-station

B-(1) New 33/11 kV sub-station (Electrical works)

Supply of 3.15 MVA 33/11KV Copper wound Power Transformer complete with first filling of transformer oil , OFF circuit tap changer and all fittings.

Supply of outdoor 11 KV 630 Amp.O/D VCB KIOSK complete with accessories including use of special tools & conducting all pre commissioning tests before energisation, filling oil etc. complete in all respect with erection& grouting of structure

Supply of outdoor 36 KV 630 Amp.O/D VCB KIOSK complete with accessories including use of special tools & conducting all pre commissioning tests before energisation, filling oil etc. complete in all respect with erection& grouting of structure

Supplyof 33/11KV S/S structure (Galvanized) on existing PCC Poles with clamps made of MS Channel 100x50x6 mm, MS Flat 50x6 and MS Sheet 216x325x6 mm as per approved design and drawing.weight.(4086.879 Kg) Approx.

Supply of control Cable of size 4 X 4 SQ.MM. 1100 Volts PVC Insulated

Supply of overhead steel cored aluminum ACSR DOG[100SqMM(6+7) /(4.72+1.57)] conductor complete in all respect as per latest specification and drawing.

Supply of earth mesh (Galvanized) at sub-station as per approved map & design using MS Flat 50 x 6 mm & MS rod 20 mm dia including laying of flat at the depth 0.65 mtr & MS rod at 3 metre depth.

Supply of M.S. Flat 50 X 6 mm (Galvanized) for earthing

Supply of earthing rod sets for S/S made with MS Rod (Galvanized ) 20 mm dia, 3 meter length

Supply of 11 /0.4 KV 25 KVA Al wound conventional outdoor type distribution transformer

Supply of metering points on 11 KV outgoing feeder at 33/11 KV S/S.

Supply of 11KV CT PT Set(200/5 Amp.)

Supply of MIP meter box having dimension 1100x625x375 mm fabricated out of 1.6 mm thick MS sheet and MS Angle size 25x25x3 mm. The test terminal block(TTB) link type shall be provided by contractor in the meter box.

Supply of GO double break without EB Isolator including hardware etc.

33KV (with 18 x 24 KV Post Insulator ) 800 Amp.

11KV ( with 9 x 12 KV Post Insulator ) 400 Amp.

Supply of horn gap sets including hardware nut & bolt & washer etc.

33KV ( with 12 x 24 KV Post Insulator ) 1 Set=3 Nos

11KV ( with 6 x 24 KV Post Insulator ) 1 Set=3 Nos

Supply of 11/0.4 KV SubStation structure set (Galvanized) on existing poles in all respect with clamps as required made from M.S. channel 100x50 X6 mm, 75x40x6 mm, M.S. angle 75x75x6 mm, and M.S. flat 50x6 mm weight(166.746 kgs.) Approx

Supply of 33 KV Sub-station type (30 KV 10 KA Station class) (1 set=3 No.) lightening arrestors including hardware, nut , bolt & washers etc.

Supply of Sub-station type (9 KV 10 KA Station class) (1 set=3 No.) lightening arrestors including hardware, nut , bolt & washers etc.

Supply of PCC Pole

PCC pole 9.0 mtrs long.(400 Kg.)

PCC pole 9.0 mtrs long.(200 Kg.)

Supply of 45 KN. porcelain disc.insulators for 33 KV (each unit consisting of 3 disc insulators & one B&S Type hardware) including all acessories like hardware fitting etc.

Supply of 45KN. porcelain disc.insulators for 11 KV (each unit consisting of 2 disc insulators & one B&S Type hardware) including all acessories like hardware fitting etc.

Supply of porcelain 33KV Pin Insulator with Pin

Supply of 11 KV Polymer Composite Pin Insulator with pin

Supply of Fire Extinguishers

Supply of PG clamps Dog to Dog

Supply of 33 or 11 kV Danger plate of size 200 X 250 mm

Supply of M.S. Nuts & Bolts (Galvanized) of assorted size

B-(2) New 33/11 kV sub-station (Yard Lighting)

Supply of PCC Poles 9 mtrs (200 Kg)

Supply of LED lighting cable from LT pole to control room with 4.00 sqmm T/C XLPE armoured cable of aluminium conductor confirming to IS (latest amendement) procured as per specification of Nigam duly clipped /hocked and insulation tape complete in all respect.

Providing and fixing of IP 65 protected LED street light fixture 70-75 watt (with surge protection device 10 KA) applicable for area lighting with extruded pressure diecast aluminium housing system luments efficacy of 100 LM/watt minimum, toughened glass with diffuser, suitable lenses on LED, 240V, 50 Hz of high power LED lamps supplied with pre- wired cabe of 1 mtr integrataed Driver shall be high efficiency having efficiency >85% and in compliance to IEC standards system life of 50,000 burning hours, CRI> 80, PF>0.90 at full load CCT 5700-6500 K fixtures shall be CE compliance. Make OSRAM/PHILIPHS/HAVELLS/CISCO/LNT/LED light fixture approved in BSR -2013 of public work department/ LED light fixture approved in integrated schedule rates- 2017 of RUIDP with five year warranty and comprehensiive maintenace. As per letter no. AVVNL/SE(TW)/XEN(TW-I)/AEN(TW-II)/TN-404 D 1547 DT; 09.02.2022

Providing and fixing of DWC Pipe 40 mm dia.

(C) 33/11 kV sub-station Augmentation

Supply of 3.15 MVA 33/11KV Copper wound Power Transformer complete with first filling of transformer oil , OFF circuit tap changer and all fittings.

Supply of outdoor 11 KV 630 Amp.O/D VCB KIOSK complete with accessories including use of special tools & conducting all pre commissioning tests before energisation, filling oil etc. complete in all respect with erection& grouting of structure

Supply of MS Channel 100x50x6 mm (Galvanized) with clamps

Supply of overhead steel cored aluminum ACSR DOG[100SqMM(6+7) /(4.72+1.57)] conductor

Supply of earth mesh (Galvanized) at sub-station as per approved map & design using MS Flat 50 x 6 mm & MS rod 20 mm dia including laying of flat at the depth 0.65 mtr & MS rod at 3 metre depth (Galvanized)

Supply of M.S. Flat 50 X 6 mm (Galvanized) for earthing

Supply of earthing rod sets for S/S made with MS Rod (Galvanized ) 20 mm dia, 3 meter length

Supply of GO double break without EB Isolator including hardware etc.

33KV (with 18 x 24 KV Post Insulator ) 800 Amp.

11KV ( with 9 x 12 KV Post Insulator ) 400 Amp.

Supply of horn gap sets including hardware nut & bolt & washer etc.

33KV ( with 12 x 24 KV Post Insulator ) 1 Set=3 Nos

Supply of 33 KV Sub-station type (30 KV 10 KA Station class) (1 set=3 No.) lightening arrestors including hardware, nut , bolt & washers etc.

Supply of PCC Poles

PCC pole 9.0 mtrs long.(400 Kg.)

Supply of 45 KN. porcelain disc.insulators for 33 KV (each unit consisting of 3 disc insulators & one B&S Type hardware) including all acessories like hardware fitting etc.

Supply of 45KN. porcelain disc.insulators for 11 KV (each unit consisting of 2 disc insulators & one B&S Type hardware) including all acessories like hardware fitting etc.

Supply of porcelain 33KV Pin Insulator with Pins

Supply of 11 KV Polymer Composite Pin Insulator with pin

Supply of PG clamps Dog to Dog

Supply of 33 or 11 kV Danger plate of size 200 X 250 mm complete in all respect

Supply of M.S. Nuts & Bolts (Galvanized) of assorted size

(D) Segregation of 11 KV Agriculture Feeders

D-(1) 11 KV over head Line 3 phase of F.S.

Supply of PCC Poles 9 mtrs (200 Kg)

Supply of overhead steel cored aluminum ACSR WEASEL [30 sq.mm (6+1)/(2.59+2.59) mm ]conductor.

Supply of 11 KV V Cross arm with top hamper & clamps (galvanized as per IS), 0.2 m long made of MS Channel 100x50x6 mm, MS Angle 65x65x6 mm & MS flat of size 50x6 mm weight(12.789 Kg.) Approx.

Supply of Galvanized Stay set of 1.8 m long, 16 mm diameter solid GS stay rod & 300x300x4 mm anchor plate including, 2 Nos. 50x8 m Stay clamp, 1 nos. HT stay guy insulator, nut bolts, 2 Nos. turn buckles & 7/3.15 mm dia GI stranded wire etc.

Stay Set

Strain/Guy Insulator

Stay Wire 7/10 mm size (1 set = 5.508 Kg)

Stay Clamps (Set = 2 Nos. Clamps) ( 1.7 Kgs. Approx)

Supply of 11 KV double pole line structure set for cut point complete on existing poles in all respect with clamp, nut & bolts as requried made from M.S.Channel 100 x 50x6 , M.S.Angle 65 x 65 x 6 mm, M.S.Angle 50 x 50 x 6 mm and M.S.Flat 50 x 6 mm ( 101.383 Kg. Approx.) (Galvanized as per IS)

Supply of earthing rod sets for 11KV lines made with MS Rod (Galvanized) 20 mm dia, 3 meter length alongwith GI wire 8 SWG (approx.) total length / weight, 17 meter / 1.64 Kg.) as per latest specification and drawing adopted & approved by NIGAM.

Supply of 11 KV Polymer Composite Pin Insulator with pin

Supply of Composite Polymer Disc insulators for 11 KV 45 KN “T&C” type

Supply of 11KV T & C Type 45 KN Hardware

Supply of PG clamps (Weasel to Weasel)

Supply of 8 SWG (4 mm dia) GI wire for continuous earthing of 11 KV Line hot dip (Galvanized)

Supply of 11 KV Danger plate of size 200 X 250 mm complete in all respect

Supply of Guarding brackets ( 1 set = 2 Nos.) per span of 11 KV made of M.S. Angle 65X65X6 mm with clamps made of Flat 50x6, using Eye Hook 300X16 mm (75% Thread with Nut of Suitable Size) (galvanized)

M.S. Angle (2x1.83 M),65X65X6mm, 10.614X2=21.228 Kg (Approx) (1set= 2 Nos)

Clamp of M S Flat 50x6 mm using Eye Hook 300X16 mm (75% Thread with Nut of Suitable Size) (1set= 2 Nos) (2.218*2= 4.436 Approx)

G I Wire 8 SWG,68 Mtr, 6.66 Kg

Supply of M.S. Nuts & Bolts (Galvanized) of assorted size

D-(2) 11 KV over head Line 1 phase of F.S.

Supply of PCC Poles 9 mtrs (200 Kg)

Supply of overhead steel cored aluminum ACSR WEASEL [30 sq.mm (6+1)/(2.59+2.59) mm ]conductor.

Supply of 11KV top hamper (galvanized as per IS), made of MS Channel 100x50x6 mm weight(2.822 Kg.) Approx.

Supply of Galvanized Stay set of 1.8 m long, 16 mm diameter solid GS stay rod & 300x300x4 mm anchor plate including, 2 Nos. 50x8 m Stay clamp, 1 nos. HT stay guy insulator, nut bolts, 2 Nos. turn buckles & 7/3.15 mm dia GI stranded wire etc.

Stay Set

Strain/Guy Insulator

Stay Wire 7/10 mm size (1 set = 5.508 Kg)

Stay Clamps (Set = 2 Nos. Clamps) ( 1.7 Kgs. Approx)

Supply of earthing rod sets for 11KV lines made with MS Rod (Galvanized) 20 mm dia, 3 meter length alongwith GI wire 8 SWG (approx.) total length / weight, 17 meter / 1.64 Kg.) as per latest specification and drawing adopted & approved by NIGAM.

Supply of 11 KV Polymer Composite Pin Insulator with pin

Supply of Composite Polymer Disc insulators for 11 KV 45 KN “T&C” type

Supply of 11KV T & C Type 45 KN Hardware

Supply of LT Porcelain Pin Insulators

Supply of LT pins

Supply of LT Porcelain Shackle Insulators

Supply of LT Shackle hardware

Supply of PG clamps (Weasel to Weasel)

Supply of 8 SWG (4 mm dia) GI wire for continuous earthing of 11 KV Line hot dip (Galvanized)

Supply of 11 KV Danger plate of size 200 X 250 mm complete in all respect

Supply of LT cross arm with clamp(Galvanized as per IS) 600mm long made of MS Angle 50x50x6mm & MS Flat 50x6 mm on the existing pole/joist complete. Weight(3.150 Kg+ 1.083 Kg=4.233) Approx.

Supply of Guarding brackets ( 1 set = 2 Nos.) per span of 11 KV made of M.S. Angle 65X65X6 mm with clamps made of Flat 50x6, using Eye Hook 300X16 mm (75% Thread with Nut of Suitable Size) (galvanized)

M.S. Angle (2x1.83 M),65X65X6mm, 10.614X2=21.228 Kg (Approx) (1set= 2 Nos)

Clamp of M S Flat 50x6 mm using Eye Hook 300X16 mm (75% Thread with Nut of Suitable Size) (1set= 2 Nos) (2.218*2= 4.436 Approx)

G I Wire 8 SWG,68 Mtr, 6.66 Kg

Supply of 11 KV channel bracket with clamp (galvanized as per IS) for Dead end points 1130 mm long, made of 75x40x6 mm & MS Flat 50x6 mm size. Weight (8.06 Kg+1.93 Kg) Approx.

Supply of 11 KV angle bracket with clamp (galvanized as per IS) for T-OFF point 1130 mm long made of MS Angle 65x65x6 mm & MS Flat 50x6 mm size. Weight (6.554 Kg+1.145 Kg) Approx.

Supply of M.S. Nuts & Bolts (Galvanized) of assorted size

D-(3) 11 KV Bay Extension of F.S.

Supply of PCC Poles 9 mtrs (400 KG)

Supply of outdoor 11 KV 630 Amp.O/D VCB KIOSK complete with accessories including use of special tools & conducting all pre commissioning tests before energisation, filling oil etc. complete in all respect with erection& grouting of structure

Supply of 11 KV Polymer Composite Pin Insulator with pin

Supply of 45 KN. porcelain disc.insulators for 11 KV (each unit consisting of 2 disc insulators & one B&S Type hardware) including all acessories etc.

Supply of overhead steel cored aluminum ACSR Dog conductor

Supply of PG Clamps for Dog Conductor

Supply of earthing rod sets for 11KV lines made with MS Rod (Galvanized) 20 mm dia, 3 meter length alongwith GI wire 8 SWG (approx.) total length / weight, 17 meter / 1.64 Kg.)

Supply of horn gap sets including hardware nut & bolt & washer etc. - 11KV ( with 6 x 24 KV Post Insulator ) 1 Set=3 Nos

Supply of Sub-station type (9 KV 10 KA Station class) (1 set=1 No.) lightening arrestors on the existing brackets in all respect as required including hardware, nut , bolt & washers etc. For O&M works INCLUDING CONNECTION WITH EARTH BY 6 SWG GI WIRE AS REQUIRED AND JUMPERING ETC., IN SEPARATE EARTH PIT

Supply of 11KV with ( 9 x 24 KV Post Insulator) 400 Amp. Double break without EB GO Isolator switch set (Air Break) (consisting of 3 limbs) including nut & bolts etc.

Supply of 11 KV Danger plate of size 200 X 250 mm complete in all respect

Supply of metering points on 11 KV outgoing feeder at 33/11 KV S/S.

Supply of 11KV CT PT Set(200/5 Amp.)

Supply of MIP meter box having dimension 1100x625x375 mm fabricated out of 1.6 mm thick MS sheet and MS Angle size 25x25x3 mm. The test terminal block(TTB) link type shall be provided by contractor in the meter box.

Supply of 11 KV Bay Channel Size of 75x40x6 [ 6 nos of 3750 mm ( Total size 22.5 mtr. = 6x3.75mtr) & 2 nos of 3400mm (Total size 6.8 mtr. = 2 x 3.4mtr.)] & 100x50x6 [6 nos of 3750 mm (Total size 22.5 mtr. = 6 x 3.75 mtr)] Approx Weight 424.30 Kgs.[(22.5mtr.+6.8mtr.) x 7.14 Kgs. Per mtr = 209.20 kgs.) + (22.5 mtr. x 9.56 kgs. per mtr. = 215.1 kgs.)

Supply of M.S. Nuts & Bolts (Galvanized) of assorted size

D-(4) 11 KV UG Cable for Highway/Road/Railway crossing of F.S.

Supply of 11 KV XLPE Insulated Armoured Cable size of 3CoreX185 Sq. mm.

Supply of Cable End Termination Kit/ST Joint, Making Outdoor/ Indoor Joint For11 kV.

XLPE 3X185 SQ.MM H.S. ON OUTDOOR TYPE

XLPE 3X185 SQ.MM H.S.S.T. JOINT

Supply of earthing rod sets for 11KV lines made with MS Rod (Galvanized) 20 mm dia, 3 meter length alongwith GI wire 8 SWG (approx.) total length / weight, 17 meter / 1.64 Kg.)

Supply of Clamp of M S Flat 50x6 mm(2x0.501m, wt. 2.36 Kg. Approx)

(E) Additional HT Lines including Bifurcation of 11 KV Feeders

E-(1) 11 KV over head Line 3 phase for bifurcation of feeders & interconnection of new33/11 KV GSS

Supply of PCC Poles 9 mtrs (200 Kg)

Supply of overhead steel cored aluminum ACSR WEASEL [30 sq.mm (6+1)/(2.59+2.59) mm ]conductor.

Supply of11 KV V Cross arm with top hamper & clamps (galvanized as per IS), 0.2 m long made of MS Channel 100x50x6 mm, MS Angle 65x65x6 mm & MS flat of size 50x6 mm weight(12.789 Kg.) Approx.

Supply of Galvanized Stay set of 1.8 m long, 16 mm diameter solid GS stay rod & 300x300x4 mm anchor plate including, 2 Nos. 50x8 m Stay clamp, 1 nos. HT stay guy insulator, nut bolts, 2 Nos. turn buckles & 7/3.15 mm dia GI stranded wire etc.

Stay Set

Strain/Guy Insulator

Stay Wire 7/10 mm size (1 set = 5.508 Kg)

Stay Clamps (Set = 2 Nos. Clamps) ( 1.7 Kgs. Approx)

Supply of 11 KV double pole line structure set for cut point complete on existing poles in all respect with clamp, nut & bolts as requried made from M.S.Channel 100 x 50x6 , M.S.Angle 65 x 65 x 6 mm, M.S.Angle 50 x 50 x 6 mm and M.S.Flat 50 x 6 mm ( 101.383 Kg. Approx.) (Galvanized as per IS)

Supply of earthing rod sets for 11KV lines made with MS Rod (Galvanized) 20 mm dia, 3 meter length alongwith GI wire 8 SWG (approx.) total length / weight, 17 meter / 1.64 Kg.)

Supply of 11 KV Polymer Composite Pin Insulator with pin

Supply of Composite Polymer Disc insulators for 11 KV 45 KN “T&C” type

Supply of 11KV T & C Type 45 KN Hardware

Supply of PG clamps (Weasel to Weasel)

Supply of 8 SWG (4 mm dia) GI wire for continuous earthing of 11 KV Line hot dip (Galvanized)

Supply of 11 KV Danger plate of size 200 X 250 mm complete in all respect

Supply of Guarding brackets ( 1 set = 2 Nos.) per span of 11 KV made of M.S. Angle 65X65X6 mm with clamps made of Flat 50x6, using Eye Hook 300X16 mm (75% Thread with Nut of Suitable Size) (galvanized)

M.S. Angle (2x1.83 M),65X65X6mm, 10.614X2=21.228 Kg (Approx) (1set= 2 Nos)

Clamp of M S Flat 50x6 mm using Eye Hook 300X16 mm (75% Thread with Nut of Suitable Size) (1set= 2 Nos) (2.218*2= 4.436 Approx)

G I Wire 8 SWG,68 Mtr, 6.66 Kg

Supply of M.S. Nuts & Bolts (Galvanized) of assorted size

E-(2) 11 KV Bay Extension for feeder bifurcation

Supply of PCC Poles 9 mtrs (400 KG)

Supply of outdoor 11 KV 630 Amp.O/D VCB KIOSK complete with accessories including use of special tools & conducting all pre commissioning tests before energisation, filling oil etc. complete in all respect with erection& grouting of structure

Supply of 11 KV Polymer Composite Pin Insulator with pin

Supply of 45 KN. porcelain disc.insulators for 11 KV (each unit consisting of 2 disc insulators & one B&S Type hardware) including all acessories etc.

Supply of overhead steel cored aluminum ACSR Dog conductor in all respect.

Supply of PG Clamps for Dog Conductor

Supply of earthing rod sets for 11KV lines made with MS Rod (Galvanized) 20 mm dia, 3 meter length alongwith GI wire 8 SWG (approx.) total length / weight, 17 meter / 1.64 Kg.)

Supply of horn gap sets including hardware nut & bolt & washer etc. - 11KV ( with 6 x 24 KV Post Insulator ) 1 Set=3 Nos

Supply of Sub-station type (9 KV 10 KA Station class) (1 set=1 No.) lightening arrestors including hardware, nut , bolt & washers etc.

Supply of 11KV with ( 9 x 24 KV Post Insulator) 400 Amp. Double break without EB GO Isolator switch set (Air Break) (consisting of 3 limbs) including nut & bolts etc.

Supply of 11 KV Danger plate of size 200 X 250 mm complete in all respect

Supply of metering points on 11 KV outgoing feeder at 33/11 KV S/S.

Supply of 11KV CT PT Set(200/5 Amp.)

Supply of MIP meter box having dimension 1100x625x375 mm fabricated out of 1.6 mm thick MS sheet and MS Angle size 25x25x3 mm. The test terminal block(TTB) link type shall be provided by contractor in the meter box.

Supply of 11 KV Bay Channel Size of 75x40x6 [ 6 nos of 3750 mm ( Total size 22.5 mtr. = 6x3.75mtr) & 2 nos of 3400mm (Total size 6.8 mtr. = 2 x 3.4mtr.)] & 100x50x6 [6 nos of 3750 mm (Total size 22.5 mtr. = 6 x 3.75 mtr)] Approx Weight 424.30 Kgs.[(22.5mtr.+6.8mtr.) x 7.14 Kgs. Per mtr = 209.20 kgs.) + (22.5 mtr. x 9.56 kgs. per mtr. = 215.1 kgs.)

Supply of M.S. Nuts & Bolts (Galvanized) of assorted size

E-(3) 11 KV UG Cable for Highway/Road/Railway crossing for feeder bifurcation & new 33/11 KV GSS 11 KV feeders interconnection

Supply of 11 KV XLPE Insulated Armoured Cable size of 3CoreX185 Sq. mm.

Supply of Cable End Termination Kit/ST Joint, Making Outdoor/ Indoor Joint For11 kV

XLPE 3X185 SQ.MM H.S. ON OUTDOOR TYPE

XLPE 3X185 SQ.MM H.S.S.T. JOINT

Supply of earthing rod sets for 11KV lines made with MS Rod (Galvanized) 20 mm dia, 3 meter length alongwith GI wire 8 SWG (approx.) total length / weight, 17 meter / 1.64 Kg.)

Supply of Clamp of M S Flat 50x6 mm(2x0.501m, wt. 2.36 Kg. Approx)

(F) HVDS

F-(1) 11 KV over head Line 3 phase of HVDS

Supply of PCC Poles 9 mtrs (200 Kg)

Supply of overhead steel cored aluminum ACSR WEASEL [30 sq.mm (6+1)/(2.59+2.59) mm ]conductor.

Supply of 11 KV V Cross arm with top hamper & clamps (galvanized as per IS), 0.2 m long made of MS Channel 100x50x6 mm, MS Angle 65x65x6 mm & MS flat of size 50x6 mm weight(12.789 Kg.) Approx.

Supply of Galvanized Stay set of 1.8 m long, 16 mm diameter solid GS stay rod & 300x300x4 mm anchor plate including, 2 Nos. 50x8 m Stay clamp, 1 nos. HT stay guy insulator, nut bolts, 2 Nos. turn buckles & 7/3.15 mm dia GI stranded wire etc.

Stay Set

Strain/Guy Insulator

Stay Wire 7/10 mm size (1 set = 5.508 Kg)

Stay Clamps (Set = 2 Nos. Clamps) ( 1.7 Kgs. Approx)

Supply of 11 KV double pole line structure set for cut point complete on existing poles in all respect with clamp, nut & bolts as requried made from M.S.Channel 100 x 50x6 , M.S.Angle 65 x 65 x 6 mm, M.S.Angle 50 x 50 x 6 mm and M.S.Flat 50 x 6 mm ( 101.383 Kg. Approx.) (Galvanized as per IS)

Supply of earthing rod sets for 11KV lines made with MS Rod (Galvanized) 20 mm dia, 3 meter length alongwith GI wire 8 SWG (approx.) total length / weight, 17 meter / 1.64 Kg.)

Supply of 11 KV Polymer Composite Pin Insulator with pin

Supply of Composite Polymer Disc insulators for 11 KV 45 KN “T&C” type

Supply of 11KV T & C Type 45 KN Hardware

Supply of PG clamps (Weasel to Weasel)

Supply of 8 SWG (4 mm dia) GI wire for continuous earthing of 11 KV Line hot dip (Galvanized)

Supply of 11 KV Danger plate of size 200 X 250 mm complete in all respect

Supply of Guarding brackets ( 1 set = 2 Nos.) per span of 11 KV made of M.S. Angle 65X65X6 mm with clamps made of Flat 50x6, using Eye Hook 300X16 mm (75% Thread with Nut of Suitable Size) (galvanized)

M.S. Angle (2x1.83 M),65X65X6mm, 10.614X2=21.228 Kg (Approx) (1set= 2 Nos)

Clamp of M S Flat 50x6 mm using Eye Hook 300X16 mm (75% Thread with Nut of Suitable Size) (1set= 2 Nos) (2.218*2= 4.436 Approx)

G I Wire 8 SWG,68 Mtr, 6.66 Kg

Supply of M.S. Nuts & Bolts (Galvanized) of assorted size

F-(2) 11 KV over head Line 1 phase of HVDS

Supply of PCC Poles 9 mtrs (200 Kg)

Supply of overhead steel cored aluminum ACSR WEASEL [30 sq.mm (6+1)/(2.59+2.59) mm ]conductor.

Supply of 11KV top hamper (galvanized as per IS), made of MS Channel 100x50x6 mm weight(2.822 Kg.) Approx.

Supply of Galvanized Stay set of 1.8 m long, 16 mm diameter solid GS stay rod & 300x300x4 mm anchor plate including, 2 Nos. 50x8 m Stay clamp, 1 nos. HT stay guy insulator, nut bolts, 2 Nos. turn buckles & 7/3.15 mm dia GI stranded wire etc.

Stay Set

Strain/Guy Insulator

Stay Wire 7/10 mm size (1 set = 5.508 Kg)

Stay Clamps (Set = 2 Nos. Clamps) ( 1.7 Kgs. Approx)

Supply of earthing rod sets for 11KV lines made with MS Rod (Galvanized) 20 mm dia, 3 meter length alongwith GI wire 8 SWG (approx.) total length / weight, 17 meter / 1.64 Kg.)

Supply of 11 KV Polymer Composite Pin Insulator with pin

Supply of Composite Polymer Disc insulators for 11 KV 45 KN “T&C” type

Supply of 11KV T & C Type 45 KN Hardware

Supply of LT Porcelain Pin Insulators

Supply of LT pins.

Supply of LT Porcelain Shackle Insulators

Supply of LT Shackle hardware

Supply of PG clamps (Weasel to Weasel)

Supply of 8 SWG (4 mm dia) GI wire (Galvanized)

Supply of 11 KV Danger plate of size 200 X 250 mm complete in all respect

Supply of LT cross arm with clamp(Galvanized as per IS) 600mm long made of MS Angle 50x50x6mm & MS Flat 50x6 mm on the existing pole/joist complete. Weight(3.150 Kg+ 1.083 Kg) Approx.

Supply of Guarding brackets ( 1 set = 2 Nos.) per span of 11 KV made of M.S. Angle 65X65X6 mm with clamps made of Flat 50x6, using Eye Hook 300X16 mm (75% Thread with Nut of Suitable Size) (galvanized)

M.S. Angle (2x1.83 M),65X65X6mm, 10.614X2=21.228 Kg (Approx) (1set= 2 Nos)

Clamp of M S Flat 50x6 mm using Eye Hook 300X16 mm (75% Thread with Nut of Suitable Size) (1set= 2 Nos) (2.218*2= 4.436 Approx)

G I Wire 8 SWG,68 Mtr, 6.66 Kg

Supply of 11 KV channel bracket with clamp (galvanized as per IS) for Dead end points 1130 mm long, made of 75x40x6 mm & MS Flat 50x6 mm size. Weight (8.06 Kg+1.93 Kg) Approx.

Supply of 11 KV angle bracket with clamp (galvanized as per IS) for T-OFF point 1130 mm long made of MS Angle 65x65x6 mm & MS Flat 50x6 mm size. Weight (6.554 Kg+1.145 Kg) Approx.

Supply of M.S. Nuts & Bolts (Galvanized) of assorted size

F-(3) DISTRIBUTION TRANSFORMER THREE PHASE (25 KVA, 40 KVA , 63 KVA, 100 KVA and 160 KVA) of HVDS

Supply of PCC Poles 9 mtrs (400 KG)

Supply of 11 /0.4 KV 63 KVA Al wound conventional outdoor type distribution transformers

Supply of 11 /0.4 KV 40 KVA Al wound conventional outdoor type distribution transformers

Supply of 11 /0.4 KV 25 KVA Al wound conventional outdoor type distribution transformers

Supply of overhead ABC(Aerial bunched cable) 1Cx25+1x25 sqmm.

Supply of overhead steel cored aluminum ACSR WEASEL [30 sq.mm (6+1)/(2.59+2.59) mm ]conductor.

Supply of 11/0.4 KV SubStation structure set (Galvanized) on existing poles in all respect with clamps as required made from M.S. channel 100x50 X6 mm, 75x40x6 mm, M.S. angle 75x75x6 mm, and M.S. flat 50x6 mm weight(166.746 kgs.) Approx

Supply of horn gap sets including hardware nut & bolt & washer etc. ( with 6 x 24 KV Post Insulator ) 1 Set=3 Nos

Supply of set of 3 nos. of earthing rod sets for S/S made with MS Rod (Galvanized) 20 mm dia, 3 meter length alongwith GI wire 8 SWG (approx. total length / weight, 50 m / 4.907 Kg.)

Supply of 11KV ( with 9 x 12 KV Post Insulator ) 400 Amp. GO double break without EB Isolator including hardware etc.

Supply of Galvanized Stay set of 1.8 m long, 16 mm diameter solid GS stay rod & 300x300x4 mm anchor plate including, 2 Nos. 50x8 m Stay clamp, 1 nos. HT stay guy insulator, nut bolts, 2 Nos. turn buckles & 7/3.15 mm dia GI stranded wire etc.

Stay Set

Strain/Guy Insulator

Stay Wire 7/10 mm size (1 set = 5.508 Kg)

Stay Clamps (Set = 2 Nos. Clamps) ( 1.7 Kgs. Approx)

Supply of 11 KV Polymer Composite Pin Insulator with pin

Supply of Composite Polymer Disc insulators for 11 KV 45 KN “T&C” type

Supply of 11KV T & C Type 45 KN Hardware

Supply of 11 KV Danger plate of size 200 X 250 mm complete in all respect

Supply of PG clamps (Weasel to Weasel)

Supply of M.S. Nuts & Bolts (Galvanized) of assorted size

F-(4) DISTRIBUTION TRANSFORMER SINGLE PHASE (25KVA, 16 KVA, 10 KVA and 5 KVA) of HVDS

Supply of PCC Poles 9 mtrs (400 KG)

Supply of 6.35KV/240 V 16 KVA aluminium wound, completely self protected distribution transformers

Supply of 6.35KV/240 V 10 KVA aluminium wound, completely self protected distribution transformers

Supply of overhead ABC(Aerial bunched cable) 1Cx25+1x25 sqmm.

Supply of overhead steel cored aluminum ACSR WEASEL [30 sq.mm (6+1)/(2.59+2.59) mm ]conductor.

Supply of 6.35 / 0.24 KV substation structure for 10/16/25 KVA complete (galvanized as per IS) complete in all respect made of MS Channel, MS angle and MS flat etc., (36.054 kg approx.)

Supply of set of 3 nos. of earthing rod sets for S/S made with MS Rod (Galvanized) 20 mm dia, 3 meter length alongwith GI wire 8 SWG (approx. total length / weight, 50 m / 4.907 Kg.)

Supply of 11 KV 200 Amp. Drop out cum isolator with 3.0 Amp. fuse & 12 KV post insulators including nut, bolt & washers.

Supply of Galvanized Stay set of 1.8 m long, 16 mm diameter solid GS stay rod & 300x300x4 mm anchor plate including, 2 Nos. 50x8 m Stay clamp, 1 nos. HT stay guy insulator, nut bolts, 2 Nos. turn buckles & 7/3.15 mm dia GI stranded wire etc.

Stay Set

Strain/Guy Insulator

Stay Wire 7/10 mm size (1 set = 5.508 Kg)

Stay Clamps (Set = 2 Nos. Clamps) ( 1.7 Kgs. Approx)

Supply of 11 KV Polymer Composite Pin Insulator with pin

Supply of Composite Polymer Disc insulators for 11 KV 45 KN “T&C” type

Supply of 11KV T & C Type 45 KN Hardware

Supply of 11 KV Danger plate of size 200 X 250 mm complete in all respect

Supply of PG clamps (Weasel to Weasel)

Supply of Distribution class (5 KA 9 KV Distribution class) lightening arrestors including hardware, nut , bolt & washers etc.

Supply of M.S. Nuts & Bolts (Galvanized) of assorted size

(G) Replacement of old frayed Conductors

G-(1) 11 kV Line : Augmentation/Reconductoring of Dog and Weasel

Supply of PCC Poles 9 mtrs (200 Kg)

Supply of 11 KV V Cross arm with top hamper & clamps (galvanized as per IS), 0.2 m long made of MS Channel 100x50x6 mm, MS Angle 65x65x6 mm & MS flat of size 50x6 mm weight(12.789 Kg.) Approx.

Supply of 11 KV Polymer Composite Pin Insulator with pin

Supply of Composite Polymer Disc insulators for 11 KV 45 KN “T&C” type

Supply of 11KV T & C Type 45 KN Hardware

Supply of overhead steel cored aluminum ACSR DOG[100SqMM(6+7) /(4.72+1.57)] conductor

Supply of PG clamps (For Dog)

Supply of Galvanized Stay set of 1.8 m long, 16 mm diameter solid GS stay rod & 300x300x4 mm anchor plate including, 2 Nos. 50x8 m Stay clamp, 1 nos. HT stay guy insulator, nut bolts, 2 Nos. turn buckles & 7/3.15 mm dia GI stranded wire etc.

Stay Set

Strain/Guy Insulator

Stay Wire 7/10 mm size (1 set = 5.508 Kg)

Stay Clamps (Set = 2 Nos. Clamps) ( 1.7 Kgs. Approx)

Supply of 11 KV Danger plate of size 200 X 250 mm complete in all respect

Supply of M.S. Nuts & Bolts (Galvanized) of assorted size

G-(2) Replacement O/H L.T. line by LT INSULATED RABBIT CONDUCTOR

Supply of PCC Poles 9 mtrs (200 Kg)

Supply of LT Insulated Rabbit Conductor [50 sq mm (6 X 3.35 + 1 X 3.35) mm]

Supply of Galvanized Stay set of 1.8 m long, 16 mm diameter solid GS stay rod & 300x300x4 mm anchor plate including, 2 Nos. 50x8 m Stay clamp, 1 nos. HT stay guy insulator, nut bolts, 2 Nos. turn buckles & 7/3.15 mm dia GI stranded wire etc.

Stay Set

Strain/Guy Insulator

Stay Wire 7/10 mm size (1 set = 5.508 Kg)

Stay Clamps (Set = 2 Nos. Clamps) ( 1.7 Kgs. Approx)

Supply of LT cross arm with clamp(Galvanized as per IS) 600mm long made of MS Angle 50x50x6mm & MS Flat 50x6 mm on the existing pole/joist complete. Weight(3.150 Kg+ 1.083 Kg) Approx.

Supply of LT Porcelain Pin Insulators

Supply of LT pins

Supply of LT Porcelain Shackle Insulators

Supply of LT Shackle hardware

Supply of M.S. Nuts & Bolts (Galvanized) of assorted size

(H) Provision of AB Cable

H-(1) LT AB Cable Single Phase

Supply of PCC Poles 9 mtrs (200 Kg)

Supply of overhead ABC(Aerial bunched cable) 1Cx25+1x25 sqmm.

Supply of Galvanized Stay set of 1.8 m long, 16 mm diameter solid GS stay rod & 300x300x4 mm anchor plate including, 2 Nos. 50x8 m Stay clamp, 1 nos. HT stay guy insulator, nut bolts, 2 Nos. turn buckles & 7/3.15 mm dia GI stranded wire etc.

Stay Set

Strain/Guy Insulator

Stay Wire 7/10 mm size (1 set = 5.508 Kg)

Stay Clamps (Set = 2 Nos. Clamps) ( 1.7 Kgs. Approx)

Supply of suspension clamps with eye hook bolt and PCC Pole Clamps (NFC type) suitable for AB Cable Complete in all respect.

Supply of dead end clamp with eye hook bolt and PCC Pole Clamps (NFC type) suitable for AB Cable Complete in all respectt.

Supply of LT Insulation piercing connector (French standard) Type-A suitable for AB cable Complete in all respect.

Supply of Insulation piercing connector (French standard) Type-B suitable for AB cable Complete in all respect.

H-(2) LT AB Cable Three Phase

Supply of PCC Poles 9 mtrs (200 Kg)

Supply of overhead ABC(Aerial bunched cable) 3Cx25+1x25 sqmm.

Supply of Galvanized Stay set of 1.8 m long, 16 mm diameter solid GS stay rod & 300x300x4 mm anchor plate including, 2 Nos. 50x8 m Stay clamp, 1 nos. HT stay guy insulator, nut bolts, 2 Nos. turn buckles & 7/3.15 mm dia GI stranded wire etc.

Stay Set

Strain/Guy Insulator

Stay Wire 7/10 mm size (1 set = 5.508 Kg)

Stay Clamps (Set = 2 Nos. Clamps) ( 1.7 Kgs. Approx)

Supply of suspension clamps with eye hook bolt and PCC Pole Clamps (NFC type) suitable for AB Cable Complete in all respect.

Supply of dead end clamp with eye hook bolt and PCC Pole Clamps (NFC type) suitable for AB Cable Complete in all respectt.

Supply of LT Insulation piercing connector (French standard) Type-A suitable for AB cable Complete in all respect.

Supply of Insulation piercing connector (French standard) Type-B suitable for AB cable Complete in all respect.

(I) 1-Phase & 3-Phase Armoured Service Line Cabling Work

Supply of ISI mark 2CX4 Sq.mm. 1100 Volt heavy duty armoured PVC XLPE Cable of Aluminium conductor conforming to IS:7098 (Part-I) (latest amended).

Supply of 4 in 1 Deepdrawn Meter Box with multiple outgoing connector.

Supply of 6 in 1 Deepdrawn Meter Box with multiple outgoing connector.

(J) Electric Vehicle Charging Station Infra

J-(1) 11 KV over head line 3 Phase of EV Charging

Supply of PCC Poles 9 mtrs (200 Kg)

Supply of overhead steel cored aluminum ACSR Rabbit Conductor.

Supply of 11 KV V Cross arm with top hamper & clamps (galvanized as per IS), 0.2 m long made of MS Channel 100x50x6 mm, MS Angle 65x65x6 mm & MS flat of size 50x6 mm weight(12.789 Kg.) Approx.

Supply of Galvanized Stay set of 1.8 m long, 16 mm diameter solid GS stay rod & 300x300x4 mm anchor plate including, 2 Nos. 50x8 m Stay clamp, 1 nos. HT stay guy insulator, nut bolts, 2 Nos. turn buckles & 7/3.15 mm dia GI stranded wire etc

Stay Set

Strain/Guy Insulator

Stay Wire 7/10 mm size (1 set = 5.508 Kg)

Stay Clamps (Set = 2 Nos. Clamps) ( 1.7 Kgs. Approx)

Supply of 11 KV double pole line structure set for cut point complete on existing poles in all respect with clamp, nut & bolts as requried made from M.S.Channel 100 x 50x6 , M.S.Angle 65 x 65 x 6 mm, M.S.Angle 50 x 50 x 6 mm and M.S.Flat 50 x 6 mm ( 101.383 Kg. Approx.) (Galvanized as per IS)

Supply of earthing rod sets for 11KV lines made with MS Rod (Galvanized) 20 mm dia, 3 meter length alongwith GI wire 8 SWG (approx.) total length / weight, 17 meter / 1.64 Kg.)

Supply of 11 KV Polymer Composite Pin Insulator with pin

Supply of Composite Polymer Disc insulators for 11 KV 45 KN “T&C” type

Supply of 11KV T & C Type 45 KN Hardware

Supply of PG clamps for rabbit

Supply of 8 SWG (4 mm dia) GI wire (Galvanized)

Supply of 11 KV Danger plate of size 200 X 250 mm complete in all respect

Supply of Guarding brackets ( 1 set = 2 Nos.) per span of 11 KV made of M.S. Angle 65X65X6 mm with clamps made of Flat 50x6, using Eye Hook 300X16 mm (75% Thread with Nut of Suitable Size) (galvanized)

M.S. Angle (2x1.83 M),65X65X6mm, 10.614X2=21.228 Kg (Approx) (1set= 2 Nos)

Clamp of M S Flat 50x6 mm using Eye Hook 300X16 mm (75% Thread with Nut of Suitable Size) (1set= 2 Nos) (2.218*2= 4.436 Approx)

G I Wire 8 SWG,68 Mtr, 6.66 Kg

Supply of M.S. Nuts & Bolts (Galvanized) of assorted size

J-(2)11 KV under ground cable of EV Charging

Supply of 11 KV XLPE Insulated Armoured Cable size of 3CoreX185 Sq. mm.

Supply of Cable End Termination Kit/ST Joint, Making Outdoor/ Indoor Joint For11 kV

XLPE 3X185 SQ.MM H.S. ON OUTDOOR TYPE

XLPE 3X185 SQ.MM H.S.S.T. JOINT

Supply of earthing rod sets for 11KV lines made with MS Rod (Galvanized) 20 mm dia, 3 meter length alongwith GI wire 8 SWG (approx.) total length / weight, 17 meter / 1.64 Kg.)

Supply of Clamp of M S Flat 50x6 mm(2x0.501m, wt. 2.36 Kg. Approx)

J-(3) DISTRIBUTION TRANSFORMER THREE PHASE (100 KVA and 160 KVA) of EV Charging

Supply of PCC Poles 9 mtrs (400 KG)

Supply of 11 /0.4 KV 100 KVA Al wound conventional outdoor type distribution transformers

Supply of overhead ABC(Aerial bunched cable) 1Cx25+1x25 sqmm.

Supply of overhead steel cored aluminum ACSR WEASEL [30 sq.mm (6+1)/(2.59+2.59) mm ]conductor.

Supply of 11/0.4 KV SubStation structure set (Galvanized) on existing poles in all respect with clamps as required made from M.S. channel 100x50 X6 mm, 75x40x6 mm, M.S. angle 75x75x6 mm, and M.S. flat 50x6 mm weight(166.746 kgs.) Approx

Supply of horn gap sets including hardware nut & bolt & washer etc. ( with 6 x 24 KV Post Insulator ) 1 Set=3 Nos

Supply of set of 3 nos. of earthing rod sets for S/S made with MS Rod (Galvanized) 20 mm dia, 3 meter length alongwith GI wire 8 SWG (approx. total length / weight, 50 m / 4.907 Kg.) as per latest specification and drawing adopted & approved by NIGAM.

Supply of 11KV ( with 9 x 12 KV Post Insulator ) 400 Amp. GO double break without EB Isolator including hardware etc.

Supply of Galvanized Stay set of 1.8 m long, 16 mm diameter solid GS stay rod & 300x300x4 mm anchor plate including, 2 Nos. 50x8 m Stay clamp, 1 nos. HT stay guy insulator, nut bolts, 2 Nos. turn buckles & 7/3.15 mm dia GI stranded wire etc.,

Stay Set

Strain/Guy Insulator

Stay Wire 7/10 mm size (1 set = 5.508 Kg)

Stay Clamps (Set = 2 Nos. Clamps) ( 1.7 Kgs. Approx)

Supply of 11 KV Polymer Composite Pin Insulator with pin

Supply of Composite Polymer Disc insulators for 11 KV 45 KN “T&C” type

Supply of 11KV T & C Type 45 KN Hardware

Supply of 11 KV Danger plate of size 200 X 250 mm complete in all respect

Supply of PG clamps (Weasel to Weasel)

Supply of M.S. Nuts & Bolts (Galvanized) of assorted size

Description of Work / Item(s)

Amount

(A) 33 KV for New 33 KV S/S and 33 KV Feeder Bifurcation/ interconnection etc

A-(1) 33 KV (Overhead) Line for New 33 KV S/S and 33 KV Feeder Bifurcation/ interconnection etc

Erection of PCC Poles in all types of soil & allignment including excavation of pit size 1.2x0.6x1.5 cum. for 9 mtrs (400 KG) and 1.2x0.6x1.35 cum PCC poles in ground and back filling soil consolidating each deposit layer of 0.15 mtr. by watering and ramming etc. in the length.

In normal soil

In ordinary rock/Hard Soil which does not require drilling

In ordinary rock/Hard Soil which require drilling

Erection of 33 KV double pole line structure set (Galvanized) on 9mtrs PCC poles for cut point complete on existing poles in all respect as required made from M.S. channel 100x50 X6 mm, M.S. angle 75x75x6 ,M.S. Angle 50x50x6 mm and M.S. flat 50x10 mm & 50x6 mm [excluding cost of pole] weight(142.314 kgs.) Approx

Erection of 33 KV "V" Cross Arm (Angle) with Top Hamper and clamps made of MS Angle 75x75x6mm and 65x65x6 mm, MS Channel 100x50x6 mm , clamp MS Flat 50X10 mm (galvanized as per IS) (wt.= 22.849 Kgs.)approx

Erection of 33 KV porcelain Pin insulator with Pin on pole complete including all accessories like hardware fittings etc.

Erection of 45 KN. porcelain disc.insulators for 33 KV (each unit consisting of 3 disc insulators & one B&S Type hardware) on brackets complete including all acessories etc.

Erection of overhead steel cored aluminum ACSR DOG[100SqMM(6+7) /(4.72+1.57)] conductor complete in all respect as per latest specification and drawing.

Erection of PG clamps (For Dog) complete in all respect as required for ACSR conductor,

Erection of GI stay sets (Galvanized) complete with 20 mm dia ,2.4 mtrs long stay rod and 380 x380x4mm anchor plate including stay clamps 14mm turn buckle and GI stay wire size 7/8 SWG tightened through 33 KV stay insulator including excavation of pit size 1.1x1.1x1.85 cum.in ground and refilling with proper watering & ramming etc., as required complete in all respect.

In normal soil

In ordinary rock/Hard Soil which does not require drilling

In ordinary rock/Hard Soil which require drilling

Erection of 6 SWG GI Wire for continuous earthing of 33 KV Line hot dip (Galvanised) as per technical specification, approved drawings and scope of work.

Erection of earthing rod sets made with MS Rod (Galvanized ) 20 mm dia, 3 meter length along with G.I wire 8 SWG (approx. total length / weight, 17 meter/1.64 Kg. ) .

Erection of Danger plate of size 200 X 250 mm complete in all respect

Erection of 1.8 Meter Channel Bracket made of MS Channel 100x50x6 mm (Wt. 17.21 Kg with Clamp made of flat 50x10 mm(Wt. 1.83 kg) (Galvanized as per relevant IS)

Erection of M.S. Nuts & Bolts (Galvanized) of assorted size

A-(2) 33 KV (Underground) Line for New 33 KV S/S and 33 KV Feeder Bifurcation/ interconnection etc

Laying of two (Double circuit) 33KV, XLPE (Aluminium conductor) undrground cables of SIZE 3X300 SQ.MM w/o overlapping as per relevant IS/ AVVNL standard including excavation of 50 cm width x 120 cm deep trench in Kaccha land.25 cm thick under layer of sand. 'A' class bricks or concrete block covering refilling soil in the remaining portion and providing/fixing cable route indicators at every 30Mtr.of cable and at every turn.

LAYING IN BRICKS AS PER STANDARD (Kachha road)

LAYING IN BRICKS AS PER STANDARD (Pakka road)

LAYING IN DWC PIPE OF DIA.200 MM FOR CABLE at Road crossing or wherever it is required.

Laying of Single circuit (S/C) 33 KV XLPE 3CX300 sqmm cable without Road cutting i.e. through burrowing machine "VERMIER".(120 cm deep).Use of this technology must be restricted to the situation like:- (i) When the passages available for laying the proposed cable is totally a metal or cement concrete road. ii) When the road cutting is not permitted by the local administration.

Intallation of 33 KV Cable (XLPE) termination / straight through joints ( Heat shrinkable type) as per manufacturer's kit guidance and direction including preparation of cable and testing refilling etc as required.(Including crimping of lugs)

Cable End Kit 33 KV XLPE 3CX 300 SQ.MM H.S. ON OUTDOOR TYPE

Cable Jointing Kit 33 KV XLPE 3C X 300 SQ.MM H.S.Straight Through

Erection of earthing rod sets for 11 KV lines made with MS Rod (Galvanized) 20 mm dia, 3 meter length alongwith GI wire 8 SWG (approx.) total length / weight, 17 meter / 1.64 Kg.) as per latest specification and drawing adopted & approved by NIGAM.

PROVIDING AND FIXING OF G.I. PIPE OF 150 MM DIAMETER, B-CLASS (IS:1239 MARK), AT THE STARTING AND FINISHING POINT OF 11 KV UNDER GROUND CABLES AND TO LAY & CLAMP VERTICALLY WITH THE EXISTING SUPPORT, INCLUDING LABOUR CHARGES.

Providing and laying of cement concrete in ratio 1:3:6 using 43 grade cement river sand and 12 mm to 20 mm graded blast crusher broken in pit/foundation according to the size/type of support/stay set including compacting/curing for 21 days in steel plates shuttering/farmer base.

Erection of Clamp of M S Flat 50x6 mm(2x0.501m, wt. 2.36 Kg. Approx)

Erection of Danger plate of size 200 X 250 mm complete in all respect

(B) New 33/11 kV sub-station

B-(1) New 33/11 kV sub-station (Electrical works)

Erection,Loading & unloading, testing and commissioning of 3.15 MVA 33/11KV Copper wound Power Transformer complete with first filling of transformer oil , OFF circuit tap changer and all fittings.

Erection of outdoor 11 KV 630 Amp.O/D VCB KIOSK complete with accessories including use of special tools & conducting all pre commissioning tests before energisation, filling oil etc. complete in all respect with erection& grouting of structure (Including civil works). Constn. of 11 KV VCB Kiosk Plate form 3.0 x 1.5 x 1.5 Mtrs. Including excavation in all type of soil up to the depth of 900 mm, foundation concrete in C.C. - 1 : 5 :10 for 150 mm thickness, brick masonary in cement mortar of mix. 1:8 with top of the plate form finished with 100 mm layer of C.C. 1:2:4 including fixing of foundation bolts and cement plaster - 20 mm thick of mix ratio 1:6, on all the exposed surfaces of the plate form - complete in all respect.

Erection of outdoor 36 KV 630 Amp.O/D VCB KIOSK complete with accessories including use of special tools & conducting all pre commissioning tests before energisation, filling oil etc. complete in all respect with erection& grouting of structure (Including civil works). Constn. Of 36 KV VCB Kiosk Plate form 3.0 x 1.5 x 1.5 Mtrs. Including excavation in all type of soil up to the depth of 900 mm, foundation concrete in C.C. - 1 : 5 :10 for 150 mm thickness, brick masonary in cement mortar of mix. 1:8 with top of the plate form finished with 100 mm layer of C.C. 1:2:4 including fixing of foundation bolts and cement plaster - 20 mm thick of mix ratio 1:6, on all the exposed surfaces of the plate form - complete in all respect.

Erection of 33/11KV S/S structure (Galvanized) on existing PCC Poles with clamps made of MS Channel 100x50x6 mm, MS Flat 50x6 and MS Sheet 216x325x6 mm as per approved design and drawing.weight.(4086.879 Kg) Approx.

Laying, Testing Termination of control Cable of size 4 X 4 SQ.MM. 1100 Volts PVC Insulated including supply and installation of ferrules to design various cores of control cables by terminal no. of identification including utilisation of cable gland.

Erection of overhead steel cored aluminum ACSR DOG[100SqMM(6+7) /(4.72+1.57)] conductor complete in all respect as per latest specification and drawing.

Erection of earth mesh (Galvanized) at sub-station as per approved map & design using MS Flat 50 x 6 mm & MS rod 20 mm dia including laying of flat at the depth 0.65 mtr & MS rod at 3 metre depth Welding & jointing at joints, structures & equipments etc. in switch yard area of 35 M x 35 M as per drawing (Galvanized)

Laying of M.S. Flat 50 X 6 mm (Galvanized) for earthing

Erection of earthing rod sets for S/S made with MS Rod (Galvanized ) 20 mm dia, 3 meter length

Installation of 11 /0.4 KV 25 KVA Al wound conventional outdoor type distribution transformers with all fittings and accessories and first filling of transformer oil alongwith MCCB. Protection on LV side confirming to technical specification

Installation of metering points on 11 KV outgoing feeder at 33/11 KV S/S.The installation work to be carried out as per drawing/design,under the supervision of concern Assistant Engineer

Mounting structure (Galvanized)

The requisite steel members will be supplied by contractor including the hardware.Contractor shall joint/weld the members to form the mounting structure as per drawing.Necessary tools,welding ,machines,lifting devics etc. shall be arranged by contractor. Structure Should be made of MS Angle 50x50x6mm, 45x45x5 mm and MS Chennel 100x50x6 mm(Approx Weight 147.88 Kg)

Civil works

Erection of lattices in alignment including excavation and concreting of structure foundation including cement, sand and grit 20 mm size (crusher broken) having ratio 1:3:6 and grit 40 mm size for ratio 1:5:10 and curing for period as required (21 days). Area of concreting will be as per the drawing.

Installation of Metering equipments:

Installation 11KV CT PT Set(200/5 Amp.)

Installation MIP meter box having dimension 1100x625x375 mm fabricated out of 1.6 mm thick MS sheet and MS Angle size 25x25x3 mm. The meter box will be fixed firmly with sufficient strength at a place as per drawing. The test terminal block(TTB) link type shall be provided by contractor in the meter box.

The required cables from CTPT set to meter box laid down in 50 mm GI pipe with suitable bends & nipples, shall be provided by contractor alongwith the consumable items such as PVC tapes, petroleum jelly etc. The cable should be PVC multi strand copper 4 core 2.5/4 Sq. mm ISI marked and firm & tight connections shall be made by suitable connector e.g. at CTPT sets by using clamps and at meter/TTB by suitable lugs etc. The CTPT sets so installed shall be earthed by means of the MS Flat (size 50x6 mm) by joining it with the nearest earthing available at the sub-station. Requisite earthing material shall be made available by the contractor.

Fixing of GO double break without EB Isolator on existing bracket complete in all respect as required including hardware etc.

33KV (with 18 x 24 KV Post Insulator ) 800 Amp.

11KV ( with 9 x 12 KV Post Insulator ) 400 Amp.

Fixing of horn gap sets on existing brackets in all respect as required including hardware nut & bolt & washer etc.

33KV ( with 12 x 24 KV Post Insulator ) 1 Set=3 Nos

11KV ( with 6 x 24 KV Post Insulator ) 1 Set=3 Nos

Fixing of 11/0.4 KV SubStation structure set (Galvanized) on existing poles in all respect with clamps as required made from M.S. channel 100x50 X6 mm, 75x40x6 mm, M.S. angle 75x75x6 mm, and M.S. flat 50x6 mm weight(166.746 kgs.) Approx

Fixing of 33 KV Sub-station type (30 KV 10 KA Station class) (1 set=3 No.) lightening arrestors on the existing brackets in all respect as required including hardware, nut , bolt & washers etc. For O&M works.

Fixing of Sub-station type (9 KV 10 KA Station class) (1 set=3 No.) lightening arrestors on the existing brackets in all respect as required including hardware, nut , bolt & washers etc. For O&M works INCLUDING CONNECTION WITH EARTH BY 6 SWG GI WIRE AS REQUIRED AND JUMPERING ETC., IN SEPARATE EARTH PIT

Erection of PCC Poles in all types of soil & allignment including excavation of pit size 1.2x0.6x1.5 cum. for 9 mtrs PCC Poles in ground and back filling soil consolidating each deposit layer of 0.15 mtr. by watering and ramming etc. in the length.

PCC pole 9.0 mtrs long.(400 Kg.)

In normal soil

In ordinary rock/Hard Soil which does not require drilling

In ordinary rock/Hard Soil which require drilling

PCC pole 9.0 mtrs long.(200 Kg.)

In normal soil

In ordinary rock/Hard Soil which does not require drilling

In ordinary rock/Hard Soil which require drilling

Construction of 33/11KV Transformers plateform 2.4 x 2.4x 2.0 Mtrs. Including excavation in all type of soil up to the depth of 900 mm, foundation concrete in C.C. - 1 : 5 :10 for 150 mm thickness, stone masonary in cement mortar of mix. 1:8 with top of the plate form finished with 100 mm layer of C.C. 1:2:4 alongwith 2 Nos. M.S. Rails 90 Pounds of 2.4 Mtr. length each, alongwith cement plaster - 20 mm thick of mix ratio 1:6, on all the exposed surfaces of the plate form - complete in all respect.

Fixing of 45 KN. porcelain disc.insulators for 33 KV (each unit consisting of 3 disc insulators & one B&S Type hardware) on brackets complete including all acessories like hardware fitting etc.

Fixing of 45KN. porcelain disc.insulators for 11 KV (each unit consisting of 2 disc insulators & one B&S Type hardware) on brackets complete including all acessories like hardware fitting etc.

Fixing of porcelain 33KV Pin Insulator with Pins on pole complete in all respect

Fixing of 11 KV Polymer Composite Pin Insulator with pin on pole complete in all respect

Installation of Fire Extinguishers

Fixing of PG clamps Dog to Dog on over headlines/jumpers, etc. All ferrous metal part intended for outdoor use except those made of stainless steel shall be protected by hot dip galvanising

Fixing of 33 or 11 kV Danger plate of size 200 X 250 mm complete in all respect

Erection of M.S. Nuts & Bolts (Galvanized) of assorted size

B-(2) New 33/11 kV sub-station (Yard Lighting)

Erection of PCC Poles in all types of soil & allignment including excavation of pit size 1.2x0.6x1.5 cum. for 9 mtrs (200 Kg) PCC poles in ground and back filling soil consolidating each deposit layer of 0.15 mtr. by watering and ramming etc. in the length.

In normal soil

In ordinary rock/Hard Soil which does not require drilling

In ordinary rock/Hard Soil which require drilling

Providing and fixing of GI bracket 30 mm dia of required size and shape including clamp of MS flat 40x4 sq mm with MS nuts & bolts and wahers for LED lighting fixtures.

Laying of LED lighting cable from LT pole to control room with 4.00 sqmm T/C XLPE armoured cable of aluminium conductor confirming to IS (latest amendement) procured as per specification of Nigam duly clipped /hocked and insulation tape complete in all respect.

Laying of under ground LT XLPE 4.00 sqmm T/C XLPE armoured cable of aluminium conductor including excavation of 30cmx120cm.deep trench in Kachh land and refilling by 25 cm thick layer of sand 'A' class bricks covering refiling soil in the remaining portion.

Pipe Earting as per IS:3043 with perforated 3.0 Mtr long 40 mm dia 'B" class GI pipe including all accessories likenut, blots, reducer,nipple wire meshed funnel, and c.c finished chamber covered with hinged type with locking arrangement CI cover, CI frame of size 300mm x300mm and embodying the pipe complete with alternate layers salt and coke/charocal,, testing of earth resistance as required .

Supply and laying following size earth wire/strip in horizontal or vertical run in ground/surface/recess including riveting , soldering, saddles, making connection etc as required 8 SWG GI (hot dipped wire)

Providing and fixing of recessed/surface mounting heavy duty horizontal type sheet steelDistribution board phophatised/ Powder painted complete with suitable rating insulated copper bus bar, shorting link, neutral link earth link and din bar, masking sheet, conforming to IS 13032 & IS 8623 incluking making internal DB terninations with copper lung testing etc. as required. Double door ( Single phase) 4 ways Make Havells, HPL, IndoAsia

Supply and fixing of following sizes (Dia) of ISI marked medium duty steel conduit along with accessoriees in surface/recessed using saddles, clamps, fastener as required including cutting the wll, covering conduit and making good the same as reuired 25mm Gr-2

P&F 240/415 V AC MCB with positive isolation of breading capacity not less than 10 KA (B/C/D tripping characteristic) ISI marked IS 8828(1996) / conforming to IEC 60898 in existing board/sheets including making connections, testing etc as required single pole MCB 6A to 32 A rating.

Providing and laying of cement concrete in ratio 1:3:6 using 43 grade cement,river sand and 12 mm to 20 mm graded blast crusher broken in pit/foundation according to the size/type of supports/stay set including compaction/curing for 21days in steel plates shuttering /farmer base.

B-(3) New 33/11 kV sub-station (Civil Building Work)

Part-A (Building andd Boundary wall Work)

Earth work in excavation in foundation trenches or drains including dressing of sides and ramming of bottoms, lift up to 1.5 Mtr. including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed within a lead of 50 meter. All kinds of soil.

Providing and laying in position cement concrete including curing compaction etc. of specified grade excluding the cost of centering and shuttering =All up to plinth level.(a) 1:4:8 (1Cement :4 Course Sand :8 Graded stone aggregate 40 mm nominal size (B-3/3.2.7)

Providing and laying in position cement concrete including curing compaction etc. of specified grade excluding the cost of centering and shuttering =All up to plinth level.(b) 1:1.5:3 (1Cement :1.5 Course Sand :3 Graded stone aggregate 20 mm nominal size)

Random Rubble stone masonary for foundation and plinth in Cement Sand Mortar above 30 Cm. thick wall in : Cement Mortar 1:6 (1-Cement:6-Sand).

Providing and laying in position specified grade of reinforced cement concrete including curing compaction finishing with rendering in cement sand mortar 1:3 (1-Cement:3-coarse sand) and making good the joints excluding the cost of centering, shuttering and reinforcement. All work up to plinth level :1:1.5:3 (1-Cement:1.5 coarse sand:3-graded stone aggregate 20 mm nominal size)

Centering and shuttering with plywood or steel sheets including strutting, propping, bracing both ways and removal of formwork for foundations in basements rafts, footings, strap beams, bases of columns , etc. up to plinth level.

Random Rubble stone masonary for super structure above plinth level one storey height walls upto 30 cm and less thickness in Cement Mortar1:6 (1- cement : 6 Sand).

Half brick masonary in super-structure upto third storey using nominal hoop reinforcement ( 2 Nos, 6mm dia bars at every fourth course ( using bricks of class designation 75 in cement mortar 1:6 (1 cement:6 coarse sand )

Brick work in partition in superstructure upto third storey 7 Cm. thick ( brick on edge ) using bricks of class desigation 75 with nominal hoop reinforcement ( 2Nos 6mm MS bar) at every fourth course in cement mortar 1:4 (1cement:4 coarse sand )

Reinforced cement concrete work in beams, suspended floors, roofs, girders having slopes up to 15o , landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral staircases, up to floor three level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1-Cement:3-coarse sand) and making good and joints excluding the cost of centering, shuttering and reinforcement: 1:1.5:3 (1-Cement:1.5 coarse sand:3-graded stone aggregate 20 mm nominal size).

Centering & shuttering with plywood or steel sheets including strutting, propping bracing bothways with wooden members and removal of formwork for s/s upto 4.5m above plinth for : Suspended floors, roofs landing,staircases, balconies, girders, cantilevers, bands,coping, bed plates,anchor blocks, sills chajjas, lintels,beams etc.

Providing and fabricating reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor three level. Hot rolled deformed -

Providing & fixing precast cement concrete coping 1:2:4 mix 50 mm thick complete as per specification : 50mm

Providing & fixing steel glazed doors, windows and ventilators shutters of standred rolled steel section joint mitred and welded with steel 13x3mm lugs 10 Cm. long embedded in cement concrete blocks 15x10x10 Cm. of 1:3:6 (1-Cement:3-coarse sand:6-graded stone aggregate 20 mm nominal size) or with wooden plugs and screws or rawl plugs and screws or with fixing clips or with bolts and nuts as required, including providing and fixing of pin headed glass panes 4mm thick with copper glazing clips and special metal-sash putty of approved make, or metal beading with screws complete including priming coat of approved steel primer, excluding the cost of metal beading and other fittings except necessary hinges of pivots steel handles and peg stay etc. as required. windows side hug.

Supplying and fixing fixed wire gauge of 14 mesh x 24 gauge to the metal frame of rolled section by metal beading 20x3mm with suitable screw at not exceeding 150 mm distance.

Providing and fixing Square bars or other flat welded to window, ventilators etc.

Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded with 15x3 mm lugs 10 Cm. long embedded in cement concrete blocks 15x10x10 Cm. of 1:3:6 (1-Cement:3-coarse sand:6-graded stone aggregate 20 mm nominal size) or with wooden plugs and screws or rawl plugs and screws or with fixing clips or with bolts and nuts as required including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer.

Providing and fixing external grade board solid core single leaf flush door shutters ISI 2202-67 marked using Phenol formal, dehydreresin in glue both sides with approved steel fittings complete as per Annexure ‘A’Commercial veneer both side, 30mm thick shutter

Plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finished:) 20 mm thick in CM 1:6 . ( B-12/12.9.2)

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade including all scaffolding:New work (Two or more coats) over and priming coat with cement primer.

Painting with weather coat paint (Asin paint/ I.C.I./Berger or eq. ISI make paint) two or more coat to give an even shade on new work.

Painting with enamel paint of approved brand and manufacture to give an even shade: Two or more coats on New work.

S & F machine cut and polished stone shelves, tands and sills in CM 1:3 with machine cut edges :Kota stone 25 to 30mm thick.

Polished Blue Kota Stone flooring skirting, laid over 20 mm thick base of C.M. 1:4 and jointed with grey cement slurry to match the shade of the slab including rubbing and polishing complete : for area of each slab up to 2001 to 5000 sq cm, 25mm thick slab.

P & F 1st quality MAT finished ceremic tile size 300x300mm comfirming to IS: 13753 colour such as white, grey, ivory, fume red brown, light green, light blue and other light shades in floors, steps, pillars etc. laid on a bed of neat cement slurry including nicely finished joints using water proof joint filler powder (Untile or Roffe make) & finishing with flush pointing in white cement mixed with pigment to match the shade of tile complete including the cost of cement mortar bed 1:4 ( 1 cement ; 4 fine sand ) 20 mm thick.

P & F 1st quality standard white, grey, ivory, fume red brown, light green, light blue and other light shades glazed tiles ISI marked [IS: 13753] of size 300mm x 200mm in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in white cement mixed with pigment to match the shade of tile complete (excluding the cost of cement plaster on walls and pillar).Category-1: Kajaria, Jhonson, Orient,Somani make etc.

Supplying and fixing dressed sand or other approved stone shelves, tands in cement mortar 1:3 with fine dressed edges : 50 mm thick.

Grading roof water proofing treatment with : Cement concrete 1:2:4 (1-Cement:2-coarse sand :4-graded stone aggregate 20mm nominal size).

Providing batta (gola) 75mm x 75mm in cement concrete (1:2:4) including finished with cement mortar 1:3 as per standard design.

Making grooves as per design in plaster 10mm to 20mm wide

Structural steel work welded in built up sections, trusses and framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete above plinth level up to 4.5 Mtr. height in R.S. Joists flats, tees, angles and channels.

Marble stone flooring table rubbed, 15 mm thick over 20 mm (Av.) thick base of CM 1:4 (1-Cement:4-coarse sand) jointing with white cement mortar 1:2 (1-White cement:2-marble dust) with pigment to match the shade of the marble slab including grinding rubbing and polishing complete.Keshariaji ( Rikhabdeo )Size up to 1501 to 3600 sq cm.

Providing & fixing ms sheet double leaf door shutters in angle iron frame 35x35x5 mm suitablly diagonally braced with 25x3mm flat ironabove and below lock rail of size 50x5 mm beading extra includingall fittings, as per direction of engg. incharge but excluding coes of chokhats including two coats of anti corrastie red oxide primer panit.MS Sheet 20 SWG.

Plaster on new surface on wall in cement sand mortar 1:4 including raking of joints etc. complete fine finish :20mm thick.

Add extra for pillar masonry including bed plates as per specifications.Bed plates to be paid separately.

Pointing on stone masonry in cement sand mortar 1:3 ( 1 cement : 3 sand ). Flush or ruled pointing.

Pointing on stone masonry in cement sand mortar 1:3 ( 1 cement : 3 sand ). Raised and Cute pointing.

Structural steel work in single section fixed without connecting plate including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete above plinth level upto 4.5 mtr. height. In flats, tees, angles and channels.

P & F steel gate, grating and grills made of angles, tees, square bars, flats, or black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide.

P & F M.S. sheet single leaf door shutter in angle iron frame 35x35x5mm suitabilly diagonally braced with 25x3mm flat iron above and below lock rail of size 50x5mm beading extra including all fittings, as per direction of Engg. incharge but excluding cost of chowkhats: including two coats of anit-corrosive red oxide primer paint.M.S. sheet 20 S.W.G.

Providing stone slab covering over drains including filling of joints in cement sand mortar 1:3 with 35mm thick cement concrete flooring 1:2:4 mix complete with good finish with : Stone slab 60 to 75 mm thick average

Cement concrete flooring grade 1:2:4 (1-Cement:2-Coarse sand:4-graded stone aggregate) rounding off edges etc. but excluding the cost of nosing of steps etc. complete :75 mm thick with 20 mm thick nominal size aggregate

Finishing with neat cement (Punning).

Earth work in surface excavation not exceeding 30 Cm. In depth but exceeding 1.5 meter in width as well as 10 Sam. on plan including disposal of excavated earth up to 50 Mtr. And lift up to 1.5 Mtr. Disposed soil to be leveled and neatly dressed : All kinds of soil.

P&F steel shutters for almirah and ward robes etc with 20 gauge (thickness 1.00 mm) steel sheet including border frame, locking arrangement with Godraj or equivalent make mortic lock with handles including painting for all inside & outside surface as per desired shades with enamel paint including primer coat & fixing with hold fast, iron clips etc complete in all respect having superior finishing (Front elevation area to be measured).

Construction of granular sub base by providing well graded material spreading in uniform layers with tractor mount grader on prepared surface mixing by mix in place method with rotarator at one and compacting with smoth wheel roller to achives the desired density complete as per morth specification clause 401 By mix place method for grading III metrial.

Randam rubble dry stone kharanja under floor

Cutting of consjoint / longitudinal joint 4 to 6mm wide & 75 to 100 mm deep using mechanical concrete cutter including cost of diamond bit cutting wheel and filling of bitumen sealing compound in groove including cost of sealing compound.

Earth work in excavation over areas (exceeding 30cm in depth,1.5m in width as well as 10 sqm on plan) including disposal of excavated earth with all lead and lift . disposed earth to be leveled and neatly dressed. All kind of soil.

Providing and Erecting typical citizen's information board as per approved drawing and specification made of two MS shrrt of 1.6 mm thick each of size 900mmX750 mm stiffend by angle iron 25mmX25mm X3mm all around the place and plates fixed on frame of 75mm sia pipe of 12 SWG sheet (Vertical post 3050 mm with angle holdfast and horzontal member 900mm) to be joined by embedded in cement concrete M-15 grade of block of 600MMX600mmX750mm size below ground level as per enclosed drawings and as directed by Engineering incharge.All MS will bestove anmeled on both side lettering figuring and border will be with ready mixed synthethic enamel paint of superior quality in required shade and colour etc complete in all respect.All sections of framed post and steel tube will be painted with primer and two coat of epoxy paint as per drawing and as per specification.

Part "B" Sanitary Work

P & F Indian type white glazed vitreous china 1st quality W.C. orissa pan (IS :2556 Mark) with 100 mm vitreous china P or S trap including cutting and making good the wall and floor: Size 530X410 mm.

P & F WVC wash basin (1st quality, IS. : 2556 Mark) of approved make with C.I brackets duly painted, 1 No. 15mm C.P. Pillar cock (I.S.: 8934 Mark) & 32mm. C.P. brass waste coupling of approved make, 25mm G.I. waste pipe complete including cutting & making good the wall Size 510mm*400mm

P & F Looking Mirrors with P.V.C frame of approved (Atul/equivalent) Size 500*400mm

Construction of Cement concrete chamber 125mm dia.CP Brass grating

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. (Internal work Exposed on wall) 15 mm nominal outer dia pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. (Internal work Exposed on wall) 15 mm nominal outer dia pipes 25 mm nominal outer dia pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. (Concealed work including cutting chases and making good the walls etc.,) 15 mm nominal outer dia pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings, this included jointing of pipes & fittings with one step CPVC solvent cement , trenching refilling & testing of joints complete as per direction of Engineer in Charge. (External work).25 mm nominal outer dia pipes

P & F Bib cock ( IS : 8931 mark ) superior quality of approved make : ( a ) Brass 400gm.15mm nominal bore.

( b ) P & F Bib cock ( IS : 8931 mark ) superior quality of approved make : C.P. brass long body, 15mm nominal bore weight not less than 690 gm.

P & F Ball cock ( IS:1703 mark ) with rod and P.V.C. ball complete:Brass wt.400gm,15mm.

P & F Inlet connection ( Angle valves ) superior quality of approved make for wash basin,Gyser etc.C.P. Inlet connection 15mm brass (IS:8931 marked).

P & F Flush Cock/Flush Valve (IS:9758 Mark) or WC of approved quality make : Brass / Gun metal Half-turn wt. 1 Kg. of approved quality / make, 25 mm nominal bore.

P & F Full way valve ( IS:778 mark ) or wheel valve of approved make:-( a ) Gun metal 15mm nominal bore.

( b ) P & F Full way valve ( IS:778 mark ) or wheel valve of approved make:- Gun-metal 25mm nominal bore.

P & F PVC storage tank ( IS:12701 marked indicating the BIS license No.) of approved make with cover, 25 mm dia 1 M long G.I. over-flow pipe & 25 cm long wash out pipe with plug & socket including making connection etc.complete of approved design.500 litres capacity.

P& F rigid PVC pipe fitting (IS :4985 mark) of approved quality / make including jointing the pipe with solvent cement rubber ring and lubricant : 110mm dia ( a ) Vent cowel.

( b )P& F rigid PVC pipe fitting (IS :4985 mark) of approved quality / make including jointing the pipe with solvent cement rubber ring and lubricant : 110mm dia Bend 87.5

( c ) P& F rigid PVC pipe fitting (IS :4985 mark) of approved quality / make including jointing the pipe with solvent cement rubber ring and lubricant : 110mm diaPlain Tee.

( d ) P& F rigid PVC pipe fitting (IS :4985 mark) of approved quality / make including jointing the pipe with solvent cement rubber ring and lubricant : 110mm diaPlain floor trap.

P&F rigid PVC pipe (IS:4985 mark)class 2(4kg/sq.cm) approved quality / make including joining the pipe with solvent cement rubber ring and lubricant. 110 mm dia.

Construction of manhole in all type of soil inner size 90 X 60 Cm. thick masonry in CM 1:6, 10 Cm. thick cement concrete 1:5 10 in foundation, 20 mm thick inside plaster in CM 1:6, finished with floating neat cement, 50mm thick M-15 grade C.C. flooring,making channels, 80mm thick stone slab covering with 40mm thick M-15 grade C.C.flooring , 25 Kg. CI cover with frame of 40mm dia, earthwork etc. complete as per design including disposal of surplus earth within 50 mtr. lead Depth upto 0.5mtr

Construction of septic tank in all type sof soil with 40cm thick masonry in CM 1:6 15cm thick CC bed of 1:5:10 M-15 grade CC flooring & over stone slab covering, 80mm thick slab jointing of slab in CM 1:3, Ralthal, Kharanja, 50mm thick stone partiton walls, 20mm thick plaster in CM 1:6 finished with neat floating cement, 4Nos C.I. foot rests of approved design, two No. 450mm dia 25Kg each C.I. cover with frame, earth work etc. complete as per approed drawing incl. disposal of surplus earth wtihin a lead of 50mtr Size 200X100X130cm (for 10users) with 115mm thick RCC (M-20) slab with Tor steel reinforcement 8 mm dia @ 13 cm c/c bothway including shuttering complete in all respect.

P & F 15 mm dia connection pipe of approved quality / make,PVC pipe with C.P. Brass nuts up to length 370 mm.

Construction of soakage well in all type of soil 300 mm thick dry masonry top and bottom 300 mm course in CM 1:6, 80 mm thick stone slab, jointing of slab in CM 1:3, Ralthal, Kharanja, 40 mm thick M-15 grade C.C. flooring, earth work complete as per approved drawing including disposal of earth within a lead of 50 mtr. Size 240 Cm. dia outside & 240 Cm. depth.

P & F Kitchen & Lab. Sink of approved make with C.I. brackets duly painted, 40 mm C.P. waste coupling, C.P. Brass chain with rubber plug, 40 mm G.I. waste pipe up-to floor level complete including cutting and making good the wall & floor : 1.0 mm thick Salem stainless steel AISI -304 & IS 13983-1994 kitchen sink of approved make (Nirali, Neel – kanth, Jaina, Faber-Castell ) with large waste coupling. size size (inches) 24x18 x 8

Part "C":- Electric Work

Wiring of light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) on surface ISI marked ( IS:14927 P - II ) virgin material UPVC trunking & it's accessories, Hot Dipped Galvanized Modular box of 1.2 mm thick with earth terminal/ Surface Moulded virgin material UPVC Modular Box , 10 A Modular switch,Modular face plate with grid plate, 3 pin ceiling rose/holder /3 way Connector, screws, making connections, testing etc. as required. For specification of copper Conductor, Phenolic Laminated sheet's & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07 For additional technical parameters of product / work refer Annexure 'A' attached with this BSR ( a ) Short point ( up to 3 mtr. )

Wiring of light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) on surface ISI marked ( IS:14927 P - II ) virgin material UPVC trunking & it's accessories, Hot Dipped Galvanized Modular box of 1.2 mm thick with earth terminal/ Surface Moulded virgin material UPVC Modular Box , 10 A Modular switch,Modular face plate with grid plate, 3 pin ceiling rose/holder /3 way Connector, screws, making connections, testing etc. as required. For specification of copper Conductor, Phenolic Laminated sheet's & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07 For additional technical parameters of product / work refer Annexure 'A' attached with this BSR Medium point (B) ( up to 6 mtr. )

Wiring of light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) on surface ISI marked ( IS:14927 P - II ) virgin material UPVC trunking & it's accessories, Hot Dipped Galvanized Modular box of 1.2 mm thick with earth terminal/ Surface Moulded virgin material UPVC Modular Box , 10 A Modular switch,Modular face plate with grid plate, 3 pin ceiling rose/holder /3 way Connector, screws, making connections, testing etc. as required. For specification of copper Conductor, Phenolic Laminated sheet's & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07 For additional technical parameters of product / work refer Annexure 'A' attached with this BSR ( c) Long point (up to 10 mtr.)

Wiring of 3/5 pin 6 amp. Light plug point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade(IS:694) on surface ISI marked ( IS:14927 P - II ) virgin material UPVC Trunking & it's accessories, Hot Dipped Galvanized Modular box of 1.2 mm thick with earth terminal/ Surface Moulded virgin material UPVC Modular Box, modular 10A switch, 3/5 pin 6 A modular socket, Modular face plate with grid plate, screws, making connections, testing etc. as required. For specification of copper Conductor, Phenolic Laminated sheet's & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07 For additional technical parameters of product / work refer Annexure 'A' attached with this BSR On board

S&F following sizes of ISI marked ( IS:14927 P - II ) virgin material UPVC trunking along with accessories like coupler, inner, outer, elbow, square box, tee, end cap etc. on surface with screws, expansion fasteners as required. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR .25 mm x 12 mm

Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor as per PWD specification for electrical Works with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from 99.90 % purity copper, class 5 stranding in acc. to IS:8130/IEC 60228 for lower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5, in existing surface or recessed PVC/ MS conduit/casing capping making connections with Copper Lugs of suitable size, Ferrules,testing etc. as required. OEM Must have its own in house NABL lab setup for all testing facilities for wires. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR (a)2 x 2.5 sq. mm. + 1x1.5sqmm

Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor as per PWD specification for electrical Works with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from 99.90 % purity copper, class 5 stranding in acc. to IS:8130/IEC 60228 for lower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5, in existing surface or recessed PVC/ MS conduit/casing capping making connections with Copper Lugs of suitable size, Ferrules,testing etc. as required. OEM Must have its own in house NABL lab setup for all testing facilities for wires. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR( b ) 2 x 4.0 sq.mm + 1x2.5 sq.mm

Supply & drawing Wiring for sub mains ISI marked (IS:694) 1100 Volts grade PVC insulated flat twin core sheathed solid aluminium conductor with 10 SWG G.I. Support wire duly clipped etc. as required. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR .6.0 sq.mm

Providing and fixing of power plug point with non modular accessories as per PWD specification for electrical Works with Galvanized box of 1.2 mm thick with earth terminal with suitable size phenolic laminated sheet (IS : 2036 - 1995) cover including cost of 16 amp. Switch (IS :3854) and 3/6 pin 16 amp. socket outlet making connection , testing , etc. as required. . For specification of Wiring accessories refer Chapter E - 07 related item & For additional technical parameters of product / work refer Annexure 'A' attached with this BSR

Providing & Fixing of of 3/5 pin 6 amp. flush type non modular socket made out from industrial grade Polycarbonate or fire resistant ABS material, brass terminal with Porcelain based back cover & captive screws including cutting hole in tile and making connection testing etc. as required.All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .

P & F ISI marked (IS:3854) 6 amp. flush type non modular switch with CM/L no. printed and made out from industrial grade Polycarbonate or fire resistant ABS material including cutting hole in tile and making connection testing etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .

Providing & Fixing of 240/415 V AC MCB with positive isolation of 10 kA breaking capacity (B/ C/D tripping characteristic as per type of load and site requirement) 4 KV impulse withstand voltage, ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947-2, low watt losses, trip free mechanisum , energy limiting of class 3 as per IEC, minimum phase termination capacity of 35sq.mm. , conductor line load reversibility , IP 20 contact protection and fitted in existing distribution board/sheets, minimum electrical operation 20,000 upto 20 A rating and 10,000 upto 63 A, 5000 for 80 A & above rating including making connections, testing etc. as required. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test reports & All as per pre approved by Engineer in charge. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR.Single pole MCB (With B/C curve tripping Characteristics) 6 A to 32 A rating

Providing & Fixing of 240/415 V isolator ISI marked IS:13947-III/conforming to IEC 60947-3, suitable for AC22A utilization category, 4KV impulse withstand voltage, true contact indication, Red colour dolly / lever shall have single mould covering over all poles for operation , two position din rail mounting, minimum phase termination capacity of 35sq.mm. IP 20 contact protection and fitted in existing distribution board / sheet including making connections, testing etc. as required. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test reports & All as per pre approved by Engineer in charge.For additional technical parameters of product / work refer Annexure 'A' attached with this BSR .Double pole isolator 30A / 40 A rating .

Providing & Fixing of Recessed/surface mounting heavy duty horizontal type Double Door ( Metal / Glazed )Distribution board with Metal end box made out from Galvanized steel / CRCA sheet not less then 1.2 mm thick conforming to IS-8623-1 & 3 / IEC 61439- 1 & 3, powder painted complete with reversible door (for double door DB only )100 amp. insulated copper bus bar/shorting link , copper neutral link, copper earth link , color coded interconnecting wire set of suitable rating and din bar,masking sheet, making internal DB terminations with copper lugs, Ferrules, detachable gland plate, including making connections, testing etc. as required. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test reports & All as per pre approved by Engineer in charge. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR. Metal door (single phase) IK-09 and IP-43 with Metal end box 6 Way (6+2)

Plate Earthing as per IS:3043 with Hot dipped G.I. Earth plate of size 600mm x 600mm x 6.0mm by embodying 3 to 4 mtr. below the ground level with 20 mm dia. G.I. 'B' class watering Pipe ,including all accessories like nut, bolts, reducer, nipple, wire meshed funnel, and Heavy duty weather proof poly-propylene earth pit chamber with lockable Jam free lid suitable for safe working load 5000 Kg or more of size Top Dia. 225 to 260 mm, Bottom Dia 300 to 350 mm. and Height 250 to 300 mm. and embodying the pipe complete with alternate layers salt and coke/ charcoal, testing of earth resistance for value of 5 ohms or less as required & must record by engineer in charge during site visit and ensure to enter in measurment book.All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .

Supply & Laying following size earth wire in horizontal or vertical run in ground/surface/recess including riveting, soldering, saddles, making connection with GI/Cu purity purity >95% thimble etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR . 8 SWG G.I. ( Hot Dipped ) Wire

P & F 1.2mm thick M.S. Recessed fan box, hexagonal/ round of size 130 mm dia, depth 75mm, 12 mm dia rod fan hook with 100 mm length extended on each side . All as per pre approved by Engineer in charge. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR

Providing & Fixing of IK08, IP 66 protected LED Street Light Luminaire on existing bracket/pole. Fixture made of powder coated single piece pressure die cast aluminum material with heat dissipation fins on housing with UV stabilized PC (UV stablization report submitted for UV cover ) /Toughened Glass cover and secondary lens on each LED & should be SMD type of 3 to 5 watt each . The System efficacy >=125 lm/ wt and potted driver & has a unique BIS R number with Input Voltage AC 120 to 270 V AC with High voltage Cutoff @>=300 V AC and Auto resetting Safety , Power Factor >0.95 driver Efficiency >85% ,THD(I) <10% Humidity 10% to 90% RH Working Temp -5C to 45C . driver current <750mA. The luminaire shall be BIS certified and Trade mark certified. Life Expectancy Equal or more than 50000 burning hrs with Minimum 70% lumen maintened , CRI >70 and CCT 5700K +355K. Surge protection shall be min ≥ 4 KV internal and min 10 KV external inside driver compartment. driver should be Phase to phase protection of 440 V for 4 Hrs. Manufactures Word Mark/Name Engraved/Embossing on die cast housing to allow traceability/authenticity. Fixture shall be AS PER IS 10322 Complianced.OEM Must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) Certificate/ report with liable warranty of product/accessories from OEM shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR . LED Street Light fixture with Minimum lumen output 2450 lm

Providing & Fixing of IP20 SMD Mid Power LED batten type integrated light fixture made from Powder coated Extruded aluminium housing with in built driver , System lumen efficacy ≥ 110 lm/Watt output, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, CRI >80 , life time of minimum 50000 Burning Hours with , 70% of intial Lumen maintaned till life ends , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin) , Maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79 & LM80) certificate / Report from OEM shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR . 1170mm(+/-10%) LED batten with min. lumen output 2200 lm.

P & F in position frame made out of M.S. angle (riveted or welded) finished with two coats of red oxide and two coats enamel paint including cutting, welding, holes etc.of following sizes as required.For additional technical parameters of product / work refer Annexure 'A' attached with this BSR .25mm x 25mm x 5mm.

P & F paper phenolic resin bonded laminates confirming to IS : 2036 - 1995 for boxes/ frames including making holes for switches etc, with brass screws, washers/ zinc plated nut and bolts as required. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR 4.8 mm thick

SITC of Monoblock motor pump set ISI marked (IS:9079-2002) with TEFC motor, motor should be IE2 class as per IEC 60034-2-1: 2007, IEC 60034-30: 2008, & IS12615:2011. with Stainless steel Impellor, Stainless steel shaft, Mechanical seal, Single/Three phase ( 240 - 440 V ) permanent split capacitor type (PSC), fitted with thermal overload protection, Including cost of hardware etc on existing platform complete. Pump shall have following HP Rating, phase, Head, minimum Discharge respectively complete in all respect. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test certificate before execution. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR . 0.5 HP, 1-Ø, (3 - 18)Mtr, (100-26) LPM

Providing & Fixing of BEE Star rated copper wounded double ball bearing capacitor start, aluminium body & Metallic blade ceiling fan Conforming to all the performance requirements laid down in IS 374:2019 including all amendments, as applicable ; & Carry BIS licensing (i.e. ISI marking) with down rod up to 80 cm with secondary support safety cable ( steel rope) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .1200 mm Sweep BEE 2 Star rated (service value >=4.5 to < 5 )

Providing & Fixing of IS 11037:1984 marked non modular socket size flush type 120 watt rotary minimum 5 step fan regulator with CM/L no. printed and made out from industrial grade Polycarbonate or fire resistant ABS material including making connection testing etc. as required.All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .

Part-D : - Gravelling work

Supply and spreading of40 mm crusher borken hard stone aggreagate free from katcha stuff deleterious and organic matter as per IRC/MORTH specification in 33/11 kv s/s yard as per direction of Engineer incharge with all lead and lift.

(C) 33/11 kV sub-station Augmentation

Erection,Loading & unloading, testing and commissioning of 3.15 MVA 33/11KV Copper wound Power Transformer complete with first filling of transformer oil , OFF circuit tap changer and all fittings.

Erection of outdoor 11 KV 630 Amp.O/D VCB KIOSK complete with accessories including use of special tools & conducting all pre commissioning tests before energisation, filling oil etc. complete in all respect with erection& grouting of structure (Including civil works). Constn. of 11 KV VCB Kiosk Plate form 3.0 x 1.5 x 1.5 Mtrs. Including excavation in all type of soil up to the depth of 900 mm, foundation concrete in C.C. - 1 : 5 :10 for 150 mm thickness, brick masonary in cement mortar of mix. 1:8 with top of the plate form finished with 100 mm layer of C.C. 1:2:4 including fixing of foundation bolts and cement plaster - 20 mm thick of mix ratio 1:6, on all the exposed surfaces of the plate form - complete in all respect.

Fixing of MS Channel 100x50x6 mm (Galvanized) with clamps

Erection of overhead steel cored aluminum ACSR DOG[100SqMM(6+7) /(4.72+1.57)] conductor complete in all respect as per latest specification and drawing.

Fixing of earth mesh (Galvanized) at sub-station as per approved map & design using MS Flat 50 x 6 mm & MS rod 20 mm dia including laying of flat at the depth 0.65 mtr & MS rod at 3 metre depth Welding & jointing at joints, structures & equipments etc. in switch yard area of 35 M x 35 M as per drawing (Galvanized)

Laying of M.S. Flat 50 X 6 mm (Galvanized) for earthing

Erection of earthing rod sets for S/S made with MS Rod (Galvanized ) 20 mm dia, 3 meter length

Fixing of GO double break without EB Isolator on existing bracket complete in all respect as required including hardware etc.

33KV (with 18 x 24 KV Post Insulator ) 800 Amp.

11KV ( with 9 x 12 KV Post Insulator ) 400 Amp.

Fixing of horn gap sets on existing brackets in all respect as required including hardware nut & bolt & washer etc.

33KV ( with 12 x 24 KV Post Insulator ) 1 Set=3 Nos

Fixing of 33 KV Sub-station type (30 KV 10 KA Station class) (1 set=3 No.) lightening arrestors on the existing brackets in all respect as required including hardware, nut , bolt & washers etc. For O&M works.

Erection of PCC Poles in all types of soil & allignment including excavation of pit size 1.2x0.6x1.5 cum. for 9 mtrs PCC Poles in ground and back filling soil consolidating each deposit layer of 0.15 mtr. by watering and ramming etc. in the length.

PCC pole 9.0 mtrs long.(400 Kg.)

In normal soil

In ordinary rock/Hard Soil which does not require drilling

In ordinary rock/Hard Soil which require drilling

Construction of 33/11KV Transformers plate form 2.4 x 2.4x 2.0 Mtrs. Including excavation in all type of soil up to the depth of 900 mm, foundation concrete in C.C. - 1 : 5 :10 for 150 mm thickness, stone masonary in cement mortar of mix. 1:8 with top of the plate form finished with 100 mm layer of C.C. 1:2:4 alongwith 2 Nos. M.S. Rails 90 Pounds of 2.4 Mtr. length each, alongwith cement plaster - 20 mm thick of mix ratio 1:6, on all the exposed surfaces of the plate form - complete in all respect.

Fixing of 45 KN. porcelain disc.insulators for 33 KV (each unit consisting of 3 disc insulators & one B&S Type hardware) on brackets complete including all acessories like hardware fitting etc.

Fixing of 45KN. porcelain disc.insulators for 11 KV (each unit consisting of 2 disc insulators & one B&S Type hardware) on brackets complete including all acessories like hardware fitting etc.

Fixing of porcelain 33KV Pin Insulator with Pins on pole complete in all respect

Fixing of 11 KV Polymer Composite Pin Insulator with pin on pole complete in all respect

Fixing of PG clamps Dog to Dog on over headlines/jumpers, etc. All ferrous metal part intended for outdoor use except those made of stainless steel shall be protected by hot dip galvanising

Fixing of 33 or 11 kV Danger plate of size 200 X 250 mm complete in all respect

Erection of M.S. Nuts & Bolts (Galvanized) of assorted size

(D) Segregation of 11 KV Agriculture Feeders

D-(1) 11 KV over head Line 3 phase of F.S.

Erection of PCC Poles in all types of soil & allignment including excavation of pit size 1.2x0.6x1.5 cum. for 9 mtrs (200 Kg) PCC poles in ground and back filling soil consolidating each deposit layer of 0.15 mtr. by watering and ramming etc. in the length.

In normal soil

In ordinary rock/Hard Soil which does not require drilling

In ordinary rock/Hard Soil which require drilling

Drawing of overhead steel cored aluminum ACSR WEASEL [30 sq.mm (6+1)/(2.59+2.59) mm ]conductor.

Fixing of 11 KV V Cross arm with top hamper & clamps (galvanized as per IS), 0.2 m long made of MS Channel 100x50x6 mm, MS Angle 65x65x6 mm & MS flat of size 50x6 mm weight(12.789 Kg.) Approx.

Fixing of Galvanized Stay set of 1.8 m long, 16 mm diameter solid GS stay rod & 300x300x4 mm anchor plate including, 2 Nos. 50x8 m Stay clamp, 1 nos. HT stay guy insulator, nut bolts, 2 Nos. turn buckles & 7/3.15 mm dia GI stranded wire etc., as required as per technical specification, approved drawings and scope of work.

In normal soil

In ordinary rock/Hard Soil which does not require drilling

In ordinary rock/Hard Soil which require drilling

Fixing of 11 KV double pole line structure set for cut point complete on existing poles in all respect with clamp, nut & bolts as requried made from M.S.Channel 100 x 50x6 , M.S.Angle 65 x 65 x 6 mm, M.S.Angle 50 x 50 x 6 mm and M.S.Flat 50 x 6 mm ( 101.383 Kg. Approx.) (Galvanized as per IS)

Fixing of earthing rod sets for 11KV lines made with MS Rod (Galvanized) 20 mm dia, 3 meter length alongwith GI wire 8 SWG (approx.) total length / weight, 17 meter / 1.64 Kg.) as per latest specification and drawing adopted & approved by NIGAM.

Fixing of 11 KV Polymer Composite Pin Insulator with pin on pole complete in all respect

Fixing of Composite Polymer Disc insulators with hardware for 11 KV 45 KN “T&C” type (as per latest specification and drawings adopted and approved by NIGAM)

Fixing of PG clamps (Weasel to Weasel) made of aluminum alloy as per IS:617-1994 . All ferrous metal part intended for outdoor use except those made of stainless steel shall be protected by hot dip galvanizing in accordance with IS 2633-1986(latest amended)

Erection of 8 SWG (4 mm dia) GI wire for continuous earthing of 11 KV Line hot dip (Galvanized)

Erection of 11 KV Danger plate of size 200 X 250 mm complete in all respect

Erection of Guarding brackets ( 1 set = 2 Nos.) per span of 11 KV made of M.S. Angle 65X65X6 mm with clamps made of Flat 50x6, using Eye Hook 300X16 mm (75% Thread with Nut of Suitable Size) (galvanized)

Erection of M.S. Nuts & Bolts (Galvanized) of assorted size

D-(2) 11 KV over head Line 1 phase of F.S.

Erection of PCC Poles in all types of soil & allignment including excavation of pit size 1.2x0.6x1.5 cum. for 9 mtrs (200 Kg) PCC poles in ground and back filling soil consolidating each deposit layer of 0.15 mtr. by watering and ramming etc. in the length.

In normal soil

In ordinary rock/Hard Soil which does not require drilling

In ordinary rock/Hard Soil which require drilling

Drawing of overhead steel cored aluminum ACSR WEASEL [30 sq.mm (6+1)/(2.59+2.59) mm ]conductor.

Fixing of 11KV top hamper (galvanized as per IS), made of MS Channel 100x50x6 mm weight(2.822 Kg.) Approx.

Fixing of Galvanized Stay set of 1.8 m long, 16 mm diameter solid GS stay rod & 300x300x4 mm anchor plate including, 2 Nos. 50x8 m Stay clamp, 1 nos. HT stay guy insulator, nut bolts, 2 Nos. turn buckles & 7/3.15 mm dia GI stranded wire etc., as required as per technical specification, approved drawings and scope of work.

In normal soil

In ordinary rock/Hard Soil which does not require drilling

In ordinary rock/Hard Soil which require drilling

Fixing of earthing rod sets for 11KV lines made with MS Rod (Galvanized) 20 mm dia, 3 meter length alongwith GI wire 8 SWG (approx.) total length / weight, 17 meter / 1.64 Kg.) as per latest specification and drawing adopted & approved by NIGAM.

Fixing of 11 KV Polymer Composite Pin Insulator with pin on pole complete in all respect

Fixing of Composite Polymer Disc insulators with hardware for 11 KV 45 KN “T&C” type (as per latest specification and drawings adopted and approved by NIGAM)

Fixing of LT Porcelain Pin Insulators with pin (as per latest specification and drawings adopted & aprpoved by the NIGAM).

Fixing of LT Porcelain Shackle Insulators with hardware as per latest specification and drawings adopted & approved by the NIGAM.

Fixing of PG clamps (Weasel to Weasel) made of aluminum alloy as per IS:617-1994 . All ferrous metal part intended for outdoor use except those made of stainless steel shall be protected by hot dip galvanizing in accordance with IS 2633-1986(latest amended)

Erection of 8 SWG (4 mm dia) GI wire for continuous earthing of 11 KV Line hot dip (Galvanized)

Erection of 11 KV Danger plate of size 200 X 250 mm complete in all respect

Erection of LT cross arm with clamp(Galvanized as per IS) 600mm long made of MS Angle 50x50x6mm & MS Flat 50x6 mm on the existing pole/joist complete. Weight(3.150 Kg+ 1.083 Kg=4.233) Approx.

Erection of Guarding brackets ( 1 set = 2 Nos.) per span of 11 KV made of M.S. Angle 65X65X6 mm with clamps made of Flat 50x6, using Eye Hook 300X16 mm (75% Thread with Nut of Suitable Size) (galvanized)

Erection of 11 KV channel bracket with clamp (galvanized as per IS) for Dead end points 1130 mm long, made of 75x40x6 mm & MS Flat 50x6 mm size. Weight (8.06 Kg+1.93 Kg) Approx.

Erection of 11 KV angle bracket with clamp (galvanized as per IS) for T-OFF point 1130 mm long made of MS Angle 65x65x6 mm & MS Flat 50x6 mm size. Weight (6.554 Kg+1.145 Kg) Approx.

Erection of M.S. Nuts & Bolts (Galvanized) of assorted size

D-(3) 11 KV Bay Extension of F.S.

Erection of PCC Poles in all types of soil & allignment including excavation of pit size 1.2x0.6x1.5 cum. for 9 mtrs (400 KG) and 1.2x0.6x1.35 cum PCC poles in ground and back filling soil consolidating each deposit layer of 0.15 mtr. by watering and ramming etc. in the length.

In normal soil

In ordinary rock/Hard Soil which does not require drilling

In ordinary rock/Hard Soil which require drilling

Erection of outdoor 11 KV 630 Amp.O/D VCB KIOSK complete with accessories including use of special tools & conducting all pre commissioning tests before energisation, filling oil etc. complete in all respect with erection& grouting of structure (Including civil works). Constn. of 11 KV VCB Kiosk Plate form 3.0 x 1.5 x 1.5 Mtrs. Including excavation in all type of soil up to the depth of 900 mm, foundation concrete in C.C. - 1 : 5 :10 for 150 mm thickness, brick masonary in cement mortar of mix. 1:8 with top of the plate form finished with 100 mm layer of C.C. 1:2:4 including fixing of foundation bolts and cement plaster - 20 mm thick of mix ratio 1:6, on all the exposed surfaces of the plate form - complete in all respect.

Fixing of 11 KV Polymer Composite Pin Insulator with pin on pole complete in all respect

Fixing of 45 KN. porcelain disc.insulators for 11 KV (each unit consisting of 2 disc insulators & one B&S Type hardware) on brackets complete including all acessories etc.

Erection of overhead steel cored aluminum ACSR Dog conductor in all respect.

Fixing of PG Clamps for Dog Conductor

Fixing of earthing rod sets for 11KV lines made with MS Rod (Galvanized) 20 mm dia, 3 meter length alongwith GI wire 8 SWG (approx.) total length / weight, 17 meter / 1.64 Kg.) as per latest specification and drawing adopted & approved by NIGAM.

Fixing of horn gap sets on existing brackets in all respect as required including hardware nut & bolt & washer etc. - 11KV ( with 6 x 24 KV Post Insulator ) 1 Set=3 Nos

Fixing of Sub-station type (9 KV 10 KA Station class) (1 set=1 No.) lightening arrestors on the existing brackets in all respect as required including hardware, nut , bolt & washers etc. For O&M works INCLUDING CONNECTION WITH EARTH BY 6 SWG GI WIRE AS REQUIRED AND JUMPERING ETC., IN SEPARATE EARTH PIT

Assembly, installation & commissioning of 11KV with ( 9 x 24 KV Post Insulator) 400 Amp. Double break without EB GO Isolator switch set (Air Break) (consisting of 3 limbs) on erected structure with setting of accurate operation including fixing of allied accessories in all respect and jumpering on both ends with suitable clamps for connection with the system including nut & bolts etc.

Erection of 11 KV Danger plate of size 200 X 250 mm complete in all respect

Installation of metering points on 11 KV outgoing feeder at 33/11 KV S/S.The installation work to be carried out as per drawing/design,under the supervision of concern Assistant Engineer

Mounting structure (Galvanized)

The requisite steel members will be supplied by contractor including the hardware.Contractor shall joint/weld the members to form the mounting structure as per drawing.Necessary tools,welding ,machines,lifting devics etc. shall be arranged by contractor. Structure Should be made of MS Angle 50x50x6mm, 45x45x5 mm and MS Chennel 100x50x6 mm(Approx Weight 147.88 Kg)

Civil works

Erection of lattices in alignment including excavation and concreting of structure foundation including cement, sand and grit 20 mm size (crusher broken) having ratio 1:3:6 and grit 40 mm size for ratio 1:5:10 and curing for period as required (21 days). Area of concreting will be as per the drawing.

Installation of Metering equipments:

Installation 11KV CT PT Set(200/5 Amp.)

Installation MIP meter box having dimension 1100x625x375 mm fabricated out of 1.6 mm thick MS sheet and MS Angle size 25x25x3 mm. The meter box will be fixed firmly with sufficient strength at a place as per drawing. The test terminal block(TTB) link type shall be provided by contractor in the meter box.

The required cables from CTPT set to meter box laid down in 50 mm GI pipe with suitable bends & nipples, shall be provided by contractor alongwith the consumable items such as PVC tapes, petroleum jelly etc. The cable should be PVC multi strand copper 4 core 2.5/4 Sq. mm ISI marked and firm & tight connections shall be made by suitable connector e.g. at CTPT sets by using clamps and at meter/TTB by suitable lugs etc. The CTPT sets so installed shall be earthed by means of the MS Flat (size 50x6 mm) by joining it with the nearest earthing available at the sub-station. Requisite earthing material shall be made available by the contractor.

Erection of 11 KV Bay Channel Size of 75x40x6 [ 6 nos of 3750 mm ( Total size 22.5 mtr. = 6x3.75mtr) & 2 nos of 3400mm (Total size 6.8 mtr. = 2 x 3.4mtr.)] & 100x50x6 [6 nos of 3750 mm (Total size 22.5 mtr. = 6 x 3.75 mtr)] Approx Weight 424.30 Kgs.[(22.5mtr.+6.8mtr.) x 7.14 Kgs. Per mtr = 209.20 kgs.) + (22.5 mtr. x 9.56 kgs. per mtr. = 215.1 kgs.)

Erection of M.S. Nuts & Bolts (Galvanized) of assorted size

D-(4) 11 KV UG Cable for Highway/Road/Railway crossing of F.S.

Laying of two (Double circuit) 11KV, XLPE (Aluminium conductor) undrground cables of SIZE 3X185 SQ.MM w/o overlapping as per relevant IS/ AVVNL standard including excavation of 50 cm width x 120 cm deep trench in Kaccha land.25 cm thick under layer of sand. 'A' class bricks or concrete block covering refilling soil in the remaining portion and providing/fixing cable route indicators at every 30Mtr.of cable and at every turn.

LAYING IN BRICKS AS PER STANDARD (Kachha road)

LAYING IN BRICKS AS PER STANDARD (Pakka road)

LAYING IN DWC PIPE OF DIA.200 MM FOR CABLE at Road crossing or wherever it is required.

Laying of Single circuit (S/C) 11 KV XLPE 3CX185 sqmm cable without Road cutting i.e. through burrowing machine "VERMIER".(120 cm deep).Use of this technology must be restricted to the situation

Fixing of Cable End Termination Kit/ST Joint, Making Outdoor/ Indoor Joint For11 kV Aluminum Conductor XLPE Armoured HT Cable With Outdoor And Terminal End Preparation Of Joint As Per Manufactures Kit Guidance And Direction Including Preparation Of Cable End & Testing etc.

XLPE 3X185 SQ.MM H.S. ON OUTDOOR TYPE

XLPE 3X185 SQ.MM H.S.S.T. JOINT

Fixing of earthing rod sets for 11KV lines made with MS Rod (Galvanized) 20 mm dia, 3 meter length alongwith GI wire 8 SWG (approx.) total length / weight, 17 meter / 1.64 Kg.) as per latest specification and drawing adopted & approved by NIGAM.

PROVIDING AND FIXING OF G.I. PIPE OF 125 MM DIAMETER, B-CLASS (IS:1239 MARK), AT THE STARTING AND FINISHING POINT OF 11 KV UNDER GROUND CABLES AND TO LAY & CLAMP VERTICALLY WITH THE EXISTING SUPPORT, INCLUDING LABOUR CHARGES.

Providing and laying of cement concrete in ratio 1:3:6 using 43 grade cement river sand and 12 mm to 20 mm graded blast crusher broken in pit/foundation according to the size/type of support/stay set including compacting/curing for 21 days in steel plates shuttering/farmer base.

Fixing of Clamp of M S Flat 50x6 mm(2x0.501m, wt. 2.36 Kg. Approx)

(E) Additional HT Lines including Bifurcation of 11 KV Feeders

E-(1) 11 KV over head Line 3 phase for bifurcation of feeders & interconnection of new33/11 KV GSS

Erection of PCC Poles in all types of soil & allignment including excavation of pit size 1.2x0.6x1.5 cum. for 9 mtrs (200 Kg) PCC poles in ground and back filling soil consolidating each deposit layer of 0.15 mtr. by watering and ramming etc. in the length.

In normal soil

In ordinary rock/Hard Soil which does not require drilling

In ordinary rock/Hard Soil which require drilling

Drawing of overhead steel cored aluminum ACSR WEASEL [30 sq.mm (6+1)/(2.59+2.59) mm ]conductor.

Fixing of11 KV V Cross arm with top hamper & clamps (galvanized as per IS), 0.2 m long made of MS Channel 100x50x6 mm, MS Angle 65x65x6 mm & MS flat of size 50x6 mm weight(12.789 Kg.) Approx.

Fixing of Galvanized Stay set of 1.8 m long, 16 mm diameter solid GS stay rod & 300x300x4 mm anchor plate including, 2 Nos. 50x8 m Stay clamp, 1 nos. HT stay guy insulator, nut bolts, 2 Nos. turn buckles & 7/3.15 mm dia GI stranded wire etc., as required as per technical specification, approved drawings and scope of work.

In normal soil

In ordinary rock/Hard Soil which does not require drilling

In ordinary rock/Hard Soil which require drilling

Fixing of 11 KV double pole line structure set for cut point complete on existing poles in all respect with clamp, nut & bolts as requried made from M.S.Channel 100 x 50x6 , M.S.Angle 65 x 65 x 6 mm, M.S.Angle 50 x 50 x 6 mm and M.S.Flat 50 x 6 mm ( 101.383 Kg. Approx.) (Galvanized as per IS)

Fixing of earthing rod sets for 11KV lines made with MS Rod (Galvanized) 20 mm dia, 3 meter length alongwith GI wire 8 SWG (approx.) total length / weight, 17 meter / 1.64 Kg.) as per latest specification and drawing adopted & approved by NIGAM.

Fixing of 11 KV Polymer Composite Pin Insulator with pin on pole complete in all respect

Fixing of Composite Polymer Disc insulators with hardware for 11 KV 45 KN “T&C” type (as per latest specification and drawings adopted and approved by NIGAM)

Fixing of PG clamps (Weasel to Weasel) made of aluminum alloy as per IS:617-1994 . All ferrous metal part intended for outdoor use except those made of stainless steel shall be protected by hot dip galvanizing in accordance with IS 2633-1986(latest amended)

Erection of 8 SWG (4 mm dia) GI wire for continuous earthing of 11 KV Line hot dip (Galvanized)

Erection of 11 KV Danger plate of size 200 X 250 mm complete in all respect

Erection of Guarding brackets ( 1 set = 2 Nos.) per span of 11 KV made of M.S. Angle 65X65X6 mm with clamps made of Flat 50x6, using Eye Hook 300X16 mm (75% Thread with Nut of Suitable Size) (galvanized)

Erection of M.S. Nuts & Bolts (Galvanized) of assorted size

E-(2) 11 KV Bay Extension for feeder bifurcation

Erection of PCC Poles in all types of soil & allignment including excavation of pit size 1.2x0.6x1.5 cum. for 9 mtrs (400 KG) and 1.2x0.6x1.35 cum PCC poles in ground and back filling soil consolidating each deposit layer of 0.15 mtr. by watering and ramming etc. in the length.

In normal soil

In ordinary rock/Hard Soil which does not require drilling

In ordinary rock/Hard Soil which require drilling

Erection of outdoor 11 KV 630 Amp.O/D VCB KIOSK complete with accessories including use of special tools & conducting all pre commissioning tests before energisation, filling oil etc. complete in all respect with erection& grouting of structure (Including civil works). Constn. of 11 KV VCB Kiosk Plate form 3.0 x 1.5 x 1.5 Mtrs. Including excavation in all type of soil up to the depth of 900 mm, foundation concrete in C.C. - 1 : 5 :10 for 150 mm thickness, brick masonary in cement mortar of mix. 1:8 with top of the plate form finished with 100 mm layer of C.C. 1:2:4 including fixing of foundation bolts and cement plaster - 20 mm thick of mix ratio 1:6, on all the exposed surfaces of the plate form - complete in all respect.

Fixing of 11 KV Polymer Composite Pin Insulator with pin on pole complete in all respect

Fixing of 45 KN. porcelain disc.insulators for 11 KV (each unit consisting of 2 disc insulators & one B&S Type hardware) on brackets complete including all acessories etc.

Erection of overhead steel cored aluminum ACSR Dog conductor in all respect.

Fixing of PG Clamps for Dog Conductor

Fixing of earthing rod sets for 11KV lines made with MS Rod (Galvanized) 20 mm dia, 3 meter length alongwith GI wire 8 SWG (approx.) total length / weight, 17 meter / 1.64 Kg.) as per latest specification and drawing adopted & approved by NIGAM.

Fixing of horn gap sets on existing brackets in all respect as required including hardware nut & bolt & washer etc. - 11KV ( with 6 x 24 KV Post Insulator ) 1 Set=3 Nos

Fixing of Sub-station type (9 KV 10 KA Station class) (1 set=1 No.) lightening arrestors on the existing brackets in all respect as required including hardware, nut , bolt & washers etc. For O&M works INCLUDING CONNECTION WITH EARTH BY 6 SWG GI WIRE AS REQUIRED AND JUMPERING ETC., IN SEPARATE EARTH PIT

Assembly, installation & commissioning of 11KV with ( 9 x 24 KV Post Insulator) 400 Amp. Double break without EB GO Isolator switch set (Air Break) (consisting of 3 limbs) on erected structure with setting of accurate operation including fixing of allied accessories in all respect and jumpering on both ends with suitable clamps for connection with the system including nut & bolts etc.

Erection of 11 KV Danger plate of size 200 X 250 mm complete in all respect

Installation of metering points on 11 KV outgoing feeder at 33/11 KV S/S.The installation work to be carried out as per drawing/design,under the supervision of concern Assistant Engineer

Mounting structure (Galvanized)

The requisite steel members will be supplied by contractor including the hardware.Contractor shall joint/weld the members to form the mounting structure as per drawing.Necessary tools,welding ,machines,lifting devics etc. shall be arranged by contractor. Structure Should be made of MS Angle 50x50x6mm, 45x45x5 mm and MS Chennel 100x50x6 mm(Approx Weight 147.88 Kg)

Civil works

Erection of lattices in alignment including excavation and concreting of structure foundation including cement, sand and grit 20 mm size (crusher broken) having ratio 1:3:6 and grit 40 mm size for ratio 1:5:10 and curing for period as required (21 days). Area of concreting will be as per the drawing.

Installation of Metering equipments:

Installation 11KV CT PT Set(200/5 Amp.)

Installation MIP meter box having dimension 1100x625x375 mm fabricated out of 1.6 mm thick MS sheet and MS Angle size 25x25x3 mm. The meter box will be fixed firmly with sufficient strength at a place as per drawing. The test terminal block(TTB) link type shall be provided by contractor in the meter box.

The required cables from CTPT set to meter box laid down in 50 mm GI pipe with suitable bends & nipples, shall be provided by contractor alongwith the consumable items such as PVC tapes, petroleum jelly etc. The cable should be PVC multi strand copper 4 core 2.5/4 Sq. mm ISI marked and firm & tight connections shall be made by suitable connector e.g. at CTPT sets by using clamps and at meter/TTB by suitable lugs etc. The CTPT sets so installed shall be earthed by means of the MS Flat (size 50x6 mm) by joining it with the nearest earthing available at the sub-station. Requisite earthing material shall be made available by the contractor.

Erection of 11 KV Bay Channel Size of 75x40x6 [ 6 nos of 3750 mm ( Total size 22.5 mtr. = 6x3.75mtr) & 2 nos of 3400mm (Total size 6.8 mtr. = 2 x 3.4mtr.)] & 100x50x6 [6 nos of 3750 mm (Total size 22.5 mtr. = 6 x 3.75 mtr)] Approx Weight 424.30 Kgs.[(22.5mtr.+6.8mtr.) x 7.14 Kgs. Per mtr = 209.20 kgs.) + (22.5 mtr. x 9.56 kgs. per mtr. = 215.1 kgs.)

Erection of M.S. Nuts & Bolts (Galvanized) of assorted size

E-(3) 11 KV UG Cable for Highway/Road/Railway crossing for feeder bifurcation & new 33/11 KV GSS 11 KV feeders interconnection

Laying of two (Double circuit) 11KV, XLPE (Aluminium conductor) undrground cables of SIZE 3X185 SQ.MM w/o overlapping as per relevant IS/ AVVNL standard including excavation of 50 cm width x 120 cm deep trench in Kaccha land.25 cm thick under layer of sand. 'A' class bricks or concrete block covering refilling soil in the remaining portion and providing/fixing cable route indicators at every 30Mtr.of cable and at every turn.

LAYING IN BRICKS AS PER STANDARD (Kachha road)

LAYING IN BRICKS AS PER STANDARD (Pakka road)

LAYING IN DWC PIPE OF DIA.200 MM FOR CABLE at Road crossing or wherever it is required.

Laying of Single circuit (S/C) 11 KV XLPE 3CX185 sqmm cable without Road cutting i.e. through burrowing machine "VERMIER".(120 cm deep).Use of this technology must be restricted to the situation like:-

Fixing of Cable End Termination Kit/ST Joint, Making Outdoor/ Indoor Joint For11 kV Aluminum Conductor XLPE Armoured HT Cable With Outdoor And Terminal End Preparation Of Joint As Per Manufactures Kit Guidance And Direction Including Preparation Of Cable End & Testing etc.

XLPE 3X185 SQ.MM H.S. ON OUTDOOR TYPE

XLPE 3X185 SQ.MM H.S.S.T. JOINT

Fixing of earthing rod sets for 11KV lines made with MS Rod (Galvanized) 20 mm dia, 3 meter length alongwith GI wire 8 SWG (approx.) total length / weight, 17 meter / 1.64 Kg.) as per latest specification and drawing adopted & approved by NIGAM.

PROVIDING AND FIXING OF G.I. PIPE OF 125 MM DIAMETER, B-CLASS (IS:1239 MARK), AT THE STARTING AND FINISHING POINT OF 11 KV UNDER GROUND CABLES AND TO LAY & CLAMP VERTICALLY WITH THE EXISTING SUPPORT, INCLUDING LABOUR CHARGES.

Providing and laying of cement concrete in ratio 1:3:6 using 43 grade cement river sand and 12 mm to 20 mm graded blast crusher broken in pit/foundation according to the size/type of support/stay set including compacting/curing for 21 days in steel plates shuttering/farmer base.

Fixing of Clamp of M S Flat 50x6 mm(2x0.501m, wt. 2.36 Kg. Approx)

(F) HVDS

F-(1) 11 KV over head Line 3 phase of HVDS

Erection of PCC Poles in all types of soil & allignment including excavation of pit size 1.2x0.6x1.5 cum. for 9 mtrs (200 Kg) PCC poles in ground and back filling soil consolidating each deposit layer of 0.15 mtr. by watering and ramming etc. in the length.

In normal soil

In ordinary rock/Hard Soil which does not require drilling

In ordinary rock/Hard Soil which require drilling

Drawing of overhead steel cored aluminum ACSR WEASEL [30 sq.mm (6+1)/(2.59+2.59) mm ]conductor.

Fixing of 11 KV V Cross arm with top hamper & clamps (galvanized as per IS), 0.2 m long made of MS Channel 100x50x6 mm, MS Angle 65x65x6 mm & MS flat of size 50x6 mm weight(12.789 Kg.) Approx.

Fixing of Galvanized Stay set of 1.8 m long, 16 mm diameter solid GS stay rod & 300x300x4 mm anchor plate including, 2 Nos. 50x8 m Stay clamp, 1 nos. HT stay guy insulator, nut bolts, 2 Nos. turn buckles & 7/3.15 mm dia GI stranded wire etc., as required as per technical specification, approved drawings and scope of work.

In normal soil

In ordinary rock/Hard Soil which does not require drilling

In ordinary rock/Hard Soil which require drilling

Fixing of 11 KV double pole line structure set for cut point complete on existing poles in all respect with clamp, nut & bolts as requried made from M.S.Channel 100 x 50x6 , M.S.Angle 65 x 65 x 6 mm, M.S.Angle 50 x 50 x 6 mm and M.S.Flat 50 x 6 mm ( 101.383 Kg. Approx.) (Galvanized as per IS)

Fixing of earthing rod sets for 11KV lines made with MS Rod (Galvanized) 20 mm dia, 3 meter length alongwith GI wire 8 SWG (approx.) total length / weight, 17 meter / 1.64 Kg.) as per latest specification and drawing adopted & approved by NIGAM.

Fixing of 11 KV Polymer Composite Pin Insulator with pin on pole complete in all respect

Fixing of Composite Polymer Disc insulators with hardware for 11 KV 45 KN “T&C” type (as per latest specification and drawings adopted and approved by NIGAM)

Fixing of PG clamps (Weasel to Weasel) made of aluminum alloy as per IS:617-1994 . All ferrous metal part intended for outdoor use except those made of stainless steel shall be protected by hot dip galvanizing in accordance with IS 2633-1986(latest amended)

Erection of 8 SWG (4 mm dia) GI wire for continuous earthing of 11 KV Line hot dip (Galvanized)

Erection of 11 KV Danger plate of size 200 X 250 mm complete in all respect

Erection of Guarding brackets ( 1 set = 2 Nos.) per span of 11 KV made of M.S. Angle 65X65X6 mm with clamps made of Flat 50x6, using Eye Hook 300X16 mm (75% Thread with Nut of Suitable Size) (galvanized)

Erection of M.S. Nuts & Bolts (Galvanized) of assorted size

F-(2) 11 KV over head Line 1 phase of HVDS

Erection of PCC Poles in all types of soil & allignment including excavation of pit size 1.2x0.6x1.5 cum. for 9 mtrs (200 Kg) PCC poles in ground and back filling soil consolidating each deposit layer of 0.15 mtr. by watering and ramming etc. in the length.

In normal soil

In ordinary rock/Hard Soil which does not require drilling

In ordinary rock/Hard Soil which require drilling

Drawing of overhead steel cored aluminum ACSR WEASEL [30 sq.mm (6+1)/(2.59+2.59) mm ]conductor.

Fixing of 11KV top hamper (galvanized as per IS), made of MS Channel 100x50x6 mm weight(2.822 Kg.) Approx.

Fixing of Galvanized Stay set of 1.8 m long, 16 mm diameter solid GS stay rod & 300x300x4 mm anchor plate including, 2 Nos. 50x8 m Stay clamp, 1 nos. HT stay guy insulator, nut bolts, 2 Nos. turn buckles & 7/3.15 mm dia GI stranded wire etc., as required as per technical specification, approved drawings and scope of work.

In normal soil

In ordinary rock/Hard Soil which does not require drilling

In ordinary rock/Hard Soil which require drilling

Fixing of earthing rod sets for 11KV lines made with MS Rod (Galvanized) 20 mm dia, 3 meter length alongwith GI wire 8 SWG (approx.) total length / weight, 17 meter / 1.64 Kg.) as per latest specification and drawing adopted & approved by NIGAM.

Fixing of 11 KV Polymer Composite Pin Insulator with pin on pole complete in all respect

Fixing of Composite Polymer Disc insulators with hardware for 11 KV 45 KN “T&C” type (as per latest specification and drawings adopted and approved by NIGAM)

Fixing of LT Porcelain Pin Insulators with pin (as per latest specification and drawings adopted & aprpoved by the NIGAM).

Fixing of LT Porcelain Shackle Insulators with hardware as per latest specification and drawings adopted & approved by the NIGAM.

Fixing of PG clamps (Weasel to Weasel) made of aluminum alloy as per IS:617-1994 . All ferrous metal part intended for outdoor use except those made of stainless steel shall be protected by hot dip galvanizing in accordance with IS 2633-1986(latest amended)

Erection of 8 SWG (4 mm dia) GI wire for continuous earthing of 11 KV Line hot dip (Galvanized)

Erection of 11 KV Danger plate of size 200 X 250 mm complete in all respect

Erection of LT cross arm with clamp(Galvanized as per IS) 600mm long made of MS Angle 50x50x6mm & MS Flat 50x6 mm on the existing pole/joist complete. Weight(3.150 Kg+ 1.083 Kg) Approx.

Erection of Guarding brackets ( 1 set = 2 Nos.) per span of 11 KV made of M.S. Angle 65X65X6 mm with clamps made of Flat 50x6, using Eye Hook 300X16 mm (75% Thread with Nut of Suitable Size) (galvanized)

Erection of 11 KV channel bracket with clamp (galvanized as per IS) for Dead end points 1130 mm long, made of 75x40x6 mm & MS Flat 50x6 mm size. Weight (8.06 Kg+1.93 Kg) Approx.

Erection of 11 KV angle bracket with clamp (galvanized as per IS) for T-OFF point 1130 mm long made of MS Angle 65x65x6 mm & MS Flat 50x6 mm size. Weight (6.554 Kg+1.145 Kg) Approx.

Erection of M.S. Nuts & Bolts (Galvanized) of assorted size

F-(3) DISTRIBUTION TRANSFORMER THREE PHASE (25 KVA, 40 KVA , 63 KVA, 100 KVA and 160 KVA) of HVDS

Erection of PCC Poles in all types of soil & allignment including excavation of pit size 1.2x0.6x1.5 cum. for 9 mtrs (400 KG) and 1.2x0.6x1.35 cum PCC poles in ground and back filling soil consolidating each deposit layer of 0.15 mtr. by watering and ramming etc. in the length.

In normal soil

In ordinary rock/Hard Soil which does not require drilling

ordinary rock / CC Road which require drilling

Installation of 11 /0.4 KV 63 KVA Al wound conventional outdoor type distribution transformers with all fittings and accessories and first filling of transformer oil alongwith MCCB. Protection on LV side confirming to technical specification

Installation of 11 /0.4 KV 40 KVA Al wound conventional outdoor type distribution transformers with all fittings and accessories and first filling of transformer oil alongwith MCCB. Protection on LV side confirming to technical specification

Installation of 11 /0.4 KV 25 KVA Al wound conventional outdoor type distribution transformers with all fittings and accessories and first filling of transformer oil alongwith MCCB. Protection on LV side confirming to technical specification

Laying of overhead ABC(Aerial bunched cable) 1Cx25+1x25 sqmm.

Drawing & Stringing of overhead steel cored aluminum ACSR WEASEL [30 sq.mm (6+1)/(2.59+2.59) mm ]conductor.

Fixing of 11/0.4 KV SubStation structure set (Galvanized) on existing poles in all respect with clamps as required made from M.S. channel 100x50 X6 mm, 75x40x6 mm, M.S. angle 75x75x6 mm, and M.S. flat 50x6 mm weight(166.746 kgs.) Approx

Fixing of horn gap sets on existing brackets in all respect as required including hardware nut & bolt & washer etc. ( with 6 x 24 KV Post Insulator ) 1 Set=3 Nos

Erection of set of 3 nos. of earthing rod sets for S/S made with MS Rod (Galvanized) 20 mm dia, 3 meter length alongwith GI wire 8 SWG (approx. total length / weight, 50 m / 4.907 Kg.) as per latest specification and drawing adopted & approved by NIGAM.

Fixing of 11KV ( with 9 x 12 KV Post Insulator ) 400 Amp. GO double break without EB Isolator on existing bracket complete in all respect as required including hardware etc.

Fixing of Galvanized Stay set of 1.8 m long, 16 mm diameter solid GS stay rod & 300x300x4 mm anchor plate including, 2 Nos. 50x8 m Stay clamp, 1 nos. HT stay guy insulator, nut bolts, 2 Nos. turn buckles & 7/3.15 mm dia GI stranded wire etc., as required as per technical specification, approved drawings and scope of work.

In normal soil

In ordinary rock/Hard Soil which does not require drilling

In ordinary rock/Hard Soil which require drilling

Fixing of 11 KV Polymer Composite Pin Insulator with pin on pole complete in all respect

Fixing of Composite Polymer Disc insulators with hardware for 11 KV 45 KN “T&C” type (as per latest specification and drawings adopted and approved by NIGAM)

Erection of 11 KV Danger plate of size 200 X 250 mm complete in all respect

Fixing of PG clamps (Weasel to Weasel) made of aluminum alloy as per IS:617-1994 . All ferrous metal part intended for outdoor use except those made of stainless steel shall be protected by hot dip galvanizing in accordance with IS 2633-1986(latest amended)

Erection of M.S. Nuts & Bolts (Galvanized) of assorted size

F-(4) DISTRIBUTION TRANSFORMER SINGLE PHASE (25KVA, 16 KVA, 10 KVA and 5 KVA) of HVDS

Erection of PCC Poles in all types of soil & allignment including excavation of pit size 1.2x0.6x1.5 cum. for 9 mtrs (400 KG) and 1.2x0.6x1.35 cum PCC poles in ground and back filling soil consolidating each deposit layer of 0.15 mtr. by watering and ramming etc. in the length.

In normal soil

In ordinary rock/Hard Soil which does not require drilling

In ordinary rock/Hard Soil which require drilling

Installation of 6.35KV/240 V 16 KVA aluminium wound, completely self protected distribution transformers with In-built Circuit Breakers with all fittings and accessories including set of bimetallic connectors for HV & LV bushings, Non-galvanized mounting arrangement duly fitted in each of transformer and first filling of transformer oil confirming to technical specification of tender and IS:1180 Part - 1/2014 with latest amendment

Installation of 6.35KV/240 V 10 KVA aluminium wound, completely self protected distribution transformers with In-built Circuit Breakers with all fittings and accessories including set of bimetallic connectors for HV & LV bushings, Non-galvanized mounting arrangement duly fitted in each of transformer and first filling of transformer oil confirming to technical specification of tender and IS:1180 Part - 1/2014 with latest amendment

Laying of overhead ABC(Aerial bunched cable) 1Cx25+1x25 sqmm.

Drawing & Stringing of overhead steel cored aluminum ACSR WEASEL [30 sq.mm (6+1)/(2.59+2.59) mm ]conductor.

Erection of 6.35 / 0.24 KV substation structure for 10/16/25 KVA complete (galvanized as per IS) complete in all respect made of MS Channel, MS angle and MS flat etc., (as per latest specification and drawing adopted & approved by NIGAM) (36.054 kg approx.)

Erection of set of 3 nos. of earthing rod sets for S/S made with MS Rod (Galvanized) 20 mm dia, 3 meter length alongwith GI wire 8 SWG (approx. total length / weight, 50 m / 4.907 Kg.) as per latest specification and drawing adopted & approved by NIGAM.

Erection of 11 KV 200 Amp. Drop out cum isolator with 3.0 Amp. fuse & 12 KV post insulators including nut, bolt & washers as required as per technical specifications, approved drawings and scope of work.

Fixing of Galvanized Stay set of 1.8 m long, 16 mm diameter solid GS stay rod & 300x300x4 mm anchor plate including, 2 Nos. 50x8 m Stay clamp, 1 nos. HT stay guy insulator, nut bolts, 2 Nos. turn buckles & 7/3.15 mm dia GI stranded wire etc., as required as per technical specification, approved drawings and scope of work.

In normal soil

In ordinary rock/Hard Soil which does not require drilling

In ordinary rock/Hard Soil which require drilling

Fixing of 11 KV Polymer Composite Pin Insulator with pin on pole complete in all respect

Fixing of Composite Polymer Disc insulators with hardware for 11 KV 45 KN “T&C” type (as per latest specification and drawings adopted and approved by NIGAM)

Erection of 11 KV Danger plate of size 200 X 250 mm complete in all respect

Fixing of PG clamps (Weasel to Weasel) made of aluminum alloy as per IS:617-1994 . All ferrous metal part intended for outdoor use except those made of stainless steel shall be protected by hot dip galvanizing in accordance with IS 2633-1986(latest amended)

Erection of Distribution class (5 KA 9 KV Distribution class) lightening arrestors on the existing brackets in all respect as required including hardware, nut , bolt & washers etc.

Erection of M.S. Nuts & Bolts (Galvanized) of assorted size

(G) Replacement of old frayed Conductors

G-(1) 11 kV Line : Augmentation/Reconductoring of Dog and Weasel

Erection of PCC Poles in all types of soil & allignment including excavation of pit size 1.2x0.6x1.5 cum. for 9 mtrs (200 Kg) PCC poles in ground and back filling soil consolidating each deposit layer of 0.15 mtr. by watering and ramming etc. in the length.

In normal soil

In ordinary rock/Hard Soil which does not require drilling

In ordinary rock/Hard Soil which require drilling

Fixing of 11 KV V Cross arm with top hamper & clamps (galvanized as per IS), 0.2 m long made of MS Channel 100x50x6 mm, MS Angle 65x65x6 mm & MS flat of size 50x6 mm weight(12.789 Kg.) Approx.

Fixing of 11 KV Polymer Composite Pin Insulator with pin on pole complete in all respect

Fixing of Composite Polymer Disc insulators with hardware for 11 KV 45 KN “T&C” type (as per latest specification and drawings adopted and approved by NIGAM)

Erection of overhead steel cored aluminum ACSR DOG[100SqMM(6+7) /(4.72+1.57)] conductor complete in all respect as per latest specification and drawing.

Erection of PG clamps (For Dog) made of aluminum alloy as per IS:617-1994 (with latest amendments if any). All ferrous metal part intended for outdoor use except those made of stainless steel shall be protected by hot dip galvanizing in accordance with IS 2633-1986(latest amended) com plete in all respect as required for ACSR conductor,

Fixing of Galvanized Stay set of 1.8 m long, 16 mm diameter solid GS stay rod & 300x300x4 mm anchor plate including, 2 Nos. 50x8 m Stay clamp, 1 nos. HT stay guy insulator, nut bolts, 2 Nos. turn buckles & 7/3.15 mm dia GI stranded wire etc., as required as per technical specification, approved drawings and scope of work.

In normal soil

In ordinary rock/Hard Soil which does not require drilling

In ordinary rock/Hard Soil which require drilling

Erection of 11 KV Danger plate of size 200 X 250 mm complete in all respect

Erection of M.S. Nuts & Bolts (Galvanized) of assorted size

Dismenteling work in 11 KV Reconductoring

11KV, V type cross arms.

11KV Top hamper

11KV porclain pin insulators.

11KV GI Pins

11KV B&S/T&C type porcelain disc insulators. 45 KN.

H/W for 11KV B&S/T&C type porcelain disc insulators 45 KN.

AAC/AAAC/ACSR Conductor

GI wire No. 8 SWG

G-(2) Replacement O/H L.T. line by LT INSULATED RABBIT CONDUCTOR

Erection of PCC Poles in all types of soil & allignment including excavation of pit size 1.2x0.6x1.5 cum. for 9 mtrs (200 Kg) PCC poles in ground and back filling soil consolidating each deposit layer of 0.15 mtr. by watering and ramming etc. in the length.

In normal soil

In ordinary rock/Hard Soil which does not require drilling

In ordinary rock/Hard Soil which require drilling

Erection of LT Insulated Rabbit Conductor [50 sq mm (6 X 3.35 + 1 X 3.35) mm] on existing cross arms through insulator including binding with 6 mm soft aluminium conductor & twisting etc. complete in all respect. (Cost of material includes the sag and jumpering) as per latest specification & drawing adopted and approved by Nigam

Fixing of Galvanized Stay set of 1.8 m long, 16 mm diameter solid GS stay rod & 300x300x4 mm anchor plate including, 2 Nos. 50x8 m Stay clamp, 1 nos. HT stay guy insulator, nut bolts, 2 Nos. turn buckles & 7/3.15 mm dia GI stranded wire etc., as required as per technical specification, approved drawings and scope of work.

In normal soil

In ordinary rock/Hard Soil which does not require drilling

In ordinary rock/Hard Soil which require drilling

Erection of LT cross arm with clamp(Galvanized as per IS) 600mm long made of MS Angle 50x50x6mm & MS Flat 50x6 mm on the existing pole/joist complete. Weight(3.150 Kg+ 1.083 Kg) Approx.

Fixing of LT Porcelain Pin Insulators with pin (as per latest specification and drawings adopted & aprpoved by the NIGAM).

Fixing of LT Porcelain Shackle Insulators with hardware as per latest specification and drawings adopted & approved by the NIGAM.

Erection of M.S. Nuts & Bolts (Galvanized) of assorted size

Dismenteling work in LT Reconductoring

LT BRACKET 2' LONG WITH CLAMP

LT SHACKLE INSULATOR

LT SHACKLE H/W

LT PIN INSULATOR

LT GI PIN

AAC/AAAC/ACSR Conductor

(H) Provision of AB Cable

H-(1) LT AB Cable Single Phase

Erection of PCC Poles in all types of soil & allignment including excavation of pit size 1.2x0.6x1.5 cum. for 9 mtrs (200 Kg) PCC poles in ground and back filling soil consolidating each deposit layer of 0.15 mtr. by watering and ramming etc. in the length.

In normal soil

In ordinary rock/Hard Soil which does not require drilling

In ordinary rock/Hard Soil which require drilling

Laying of overhead ABC(Aerial bunched cable) 1Cx25+1x25 sqmm.

Fixing of Galvanized Stay set of 1.8 m long, 16 mm diameter solid GS stay rod & 300x300x4 mm anchor plate including, 2 Nos. 50x8 m Stay clamp, 1 nos. HT stay guy insulator, nut bolts, 2 Nos. turn buckles & 7/3.15 mm dia GI stranded wire etc., as required as per technical specification, approved drawings and scope of work.

In normal soil

In ordinary rock/Hard Soil which does not require drilling

In ordinary rock/Hard Soil which require drilling

Erection & fixing of suspension clamps with eye hook bolt and PCC Pole Clamps (NFC type) suitable for AB Cable Complete in all respect.

Erection & fixing of dead end clamp with eye hook bolt and PCC Pole Clamps (NFC type) suitable for AB Cable Complete in all respectt.

Erection & fixing of LT Insulation piercing connector (French standard) Type-A suitable for AB cable Complete in all respect.

Erection & fixing of Insulation piercing connector (French standard) Type-B suitable for AB cable Complete in all respect.

H-(2) LT AB Cable Three Phase

Erection of PCC Poles in all types of soil & allignment including excavation of pit size 1.2x0.6x1.5 cum. for 9 mtrs (200 Kg) PCC poles in ground and back filling soil consolidating each deposit layer of 0.15 mtr. by watering and ramming etc. in the length.

In normal soil

In ordinary rock/Hard Soil which does not require drilling

In ordinary rock/Hard Soil which require drilling

Erection of overhead ABC(Aerial bunched cable) 3Cx25+1x25 sqmm.

Fixing of Galvanized Stay set of 1.8 m long, 16 mm diameter solid GS stay rod & 300x300x4 mm anchor plate including, 2 Nos. 50x8 m Stay clamp, 1 nos. HT stay guy insulator, nut bolts, 2 Nos. turn buckles & 7/3.15 mm dia GI stranded wire etc., as required as per technical specification, approved drawings and scope of work.

In normal soil

In ordinary rock/Hard Soil which does not require drilling

In ordinary rock/Hard Soil which require drilling

Erection & fixing of suspension clamps with eye hook bolt and PCC Pole Clamps (NFC type) suitable for AB Cable Complete in all respect.

Erection & fixing of dead end clamp with eye hook bolt and PCC Pole Clamps (NFC type) suitable for AB Cable Complete in all respectt.

Erection & fixing of LT Insulation piercing connector (French standard) Type-A suitable for AB cable Complete in all respect.

Erection & fixing of Insulation piercing connector (French standard) Type-B suitable for AB cable Complete in all respect.

(I) 1-Phase & 3-Phase Armoured Service Line Cabling Work

Erection of ISI mark 2CX4 Sq.mm. 1100 Volt heavy duty armoured PVC XLPE Cable of Aluminium conductor conforming to IS:7098 (Part-I) (latest amended).

Fixing of 4 in 1 Deepdrawn Meter Box with multiple outgoing connector.

Fixing of 6 in 1 Deepdrawn Meter Box with multiple outgoing connector.

(J) Electric Vehicle Charging Station Infra

J-(1) 11 KV over head line 3 Phase of EV Charging

Erection of PCC Poles in all types of soil & allignment including excavation of pit size 1.2x0.6x1.5 cum. for 9 mtrs (200 Kg) PCC poles in ground and back filling soil consolidating each deposit layer of 0.15 mtr. by watering and ramming etc. in the length.

In normal soil

In ordinary rock/Hard Soil which does not require drilling

In ordinary rock/Hard Soil which require drilling

Drawing of overhead steel cored aluminum ACSR Rabbit Conductor.

Fixing of 11 KV V Cross arm with top hamper & clamps (galvanized as per IS), 0.2 m long made of MS Channel 100x50x6 mm, MS Angle 65x65x6 mm & MS flat of size 50x6 mm weight(12.789 Kg.) Approx.

Fixing of Galvanized Stay set of 1.8 m long, 16 mm diameter solid GS stay rod & 300x300x4 mm anchor plate including, 2 Nos. 50x8 m Stay clamp, 1 nos. HT stay guy insulator, nut bolts, 2 Nos. turn buckles & 7/3.15 mm dia GI stranded wire etc., as required as per technical specification, approved drawings and scope of work.

In normal soil

In ordinary rock/Hard Soil which does not require drilling

In ordinary rock/Hard Soil which require drilling

Fixing of 11 KV double pole line structure set for cut point complete on existing poles in all respect with clamp, nut & bolts as requried made from M.S.Channel 100 x 50x6 , M.S.Angle 65 x 65 x 6 mm, M.S.Angle 50 x 50 x 6 mm and M.S.Flat 50 x 6 mm ( 101.383 Kg. Approx.) (Galvanized as per IS)

Fixing of earthing rod sets for 11KV lines made with MS Rod (Galvanized) 20 mm dia, 3 meter length alongwith GI wire 8 SWG (approx.) total length / weight, 17 meter / 1.64 Kg.) as per latest specification and drawing adopted & approved by NIGAM.

Fixing of 11 KV Polymer Composite Pin Insulator with pin on pole complete in all respect

Fixing of Composite Polymer Disc insulators with hardware for 11 KV 45 KN “T&C” type (as per latest specification and drawings adopted and approved by NIGAM)

Fixing of PG clamps for rabbit made of aluminum alloy as per IS:617-1994 . All ferrous metal part intended for outdoor use except those made of stainless steel shall be protected by hot dip galvanizing in accordance with IS 2633-1986(latest amended)

Erection of 8 SWG (4 mm dia) GI wire for continuous earthing of 11 KV Line hot dip (Galvanized)

Erectionof 11 KV Danger plate of size 200 X 250 mm complete in all respect

Erection of Guarding brackets ( 1 set = 2 Nos.) per span of 11 KV made of M.S. Angle 65X65X6 mm with clamps made of Flat 50x6, using Eye Hook 300X16 mm (75% Thread with Nut of Suitable Size) (galvanized)

Erection of M.S. Nuts & Bolts (Galvanized) of assorted size

J-(2)11 KV under ground cable of EV Charging

Laying of two (Double circuit) 11KV, XLPE (Aluminium conductor) undrground cables of SIZE 3X185 SQ.MM w/o overlapping as per relevant IS/ AVVNL standard including excavation of 50 cm width x 120 cm deep trench in Kaccha land.25 cm thick under layer of sand. 'A' class bricks or concrete block covering refilling soil in the remaining portion and providing/fixing cable route indicators at every 30Mtr.of cable and at every turn.

LAYING IN BRICKS AS PER STANDARD (Kachha road)

LAYING IN BRICKS AS PER STANDARD (Pakka road)

LAYING IN DWC PIPE OF DIA.200 MM FOR CABLE at Road crossing or wherever it is required.

Laying of Single circuit (S/C) 11 KV XLPE 3CX185 sqmm cable without Road cutting i.e. through burrowing machine "VERMIER".(120 cm deep).Use of this technology must be restricted to the situation like:-

Fixing of Cable End Termination Kit/ST Joint, Making Outdoor/ Indoor Joint For11 kV Aluminum Conductor XLPE Armoured HT Cable With Outdoor And Terminal End Preparation Of Joint As Per Manufactures Kit Guidance And Direction Including Preparation Of Cable End & Testing etc.

XLPE 3X185 SQ.MM H.S. ON OUTDOOR TYPE

XLPE 3X185 SQ.MM H.S.S.T. JOINT

Fixing of earthing rod sets for 11KV lines made with MS Rod (Galvanized) 20 mm dia, 3 meter length alongwith GI wire 8 SWG (approx.) total length / weight, 17 meter / 1.64 Kg.) as per latest specification and drawing adopted & approved by NIGAM.

PROVIDING AND FIXING OF G.I. PIPE OF 125 MM DIAMETER, B-CLASS (IS:1239 MARK), AT THE STARTING AND FINISHING POINT OF 11 KV UNDER GROUND CABLES AND TO LAY & CLAMP VERTICALLY WITH THE EXISTING SUPPORT, INCLUDING LABOUR CHARGES.

Providing and laying of cement concrete in ratio 1:3:6 using 43 grade cement river sand and 12 mm to 20 mm graded blast crusher broken in pit/foundation according to the size/type of support/stay set including compacting/curing for 21 days in steel plates shuttering/farmer base.

Fixing of Clamp of M S Flat 50x6 mm(2x0.501m, wt. 2.36 Kg. Approx)

J-(3) DISTRIBUTION TRANSFORMER THREE PHASE (100 KVA and 160 KVA) of EV Charging

Erection of PCC Poles in all types of soil & allignment including excavation of pit size 1.2x0.6x1.5 cum. for 9 mtrs (400 KG) and 1.2x0.6x1.35 cum PCC poles in ground and back filling soil consolidating each deposit layer of 0.15 mtr. by watering and ramming etc. in the length.

In normal soil

In ordinary rock/Hard Soil which does not require drilling

ordinary rock / CC Road which require drilling

Installation of 11 /0.4 KV 100 KVA Al wound conventional outdoor type distribution transformers with all fittings and accessories and first filling of transformer oil alongwith MCCB. Protection on LV side confirming to technical specification

Laying of overhead ABC(Aerial bunched cable) 1Cx25+1x25 sqmm.

Drawing & Stringing of overhead steel cored aluminum ACSR WEASEL [30 sq.mm (6+1)/(2.59+2.59) mm ]conductor.

Erection of 11/0.4 KV SubStation structure set (Galvanized) on existing poles in all respect with clamps as required made from M.S. channel 100x50 X6 mm, 75x40x6 mm, M.S. angle 75x75x6 mm, and M.S. flat 50x6 mm weight(166.746 kgs.) Approx

Fixing of horn gap sets on existing brackets in all respect as required including hardware nut & bolt & washer etc. ( with 6 x 24 KV Post Insulator ) 1 Set=3 Nos

Erection of set of 3 nos. of earthing rod sets for S/S made with MS Rod (Galvanized) 20 mm dia, 3 meter length alongwith GI wire 8 SWG (approx. total length / weight, 50 m / 4.907 Kg.) as per latest specification and drawing adopted & approved by NIGAM.

Fixing of 11KV ( with 9 x 12 KV Post Insulator ) 400 Amp. GO double break without EB Isolator on existing bracket complete in all respect as required including hardware etc.

Fixing of Galvanized Stay set of 1.8 m long, 16 mm diameter solid GS stay rod & 300x300x4 mm anchor plate including, 2 Nos. 50x8 m Stay clamp, 1 nos. HT stay guy insulator, nut bolts, 2 Nos. turn buckles & 7/3.15 mm dia GI stranded wire etc., as required as per technical specification, approved drawings and scope of work.

In normal soil

In ordinary rock/Hard Soil which does not require drilling

In ordinary rock/Hard Soil which require drilling

Fixing of 11 KV Polymer Composite Pin Insulator with pin on pole complete in all respect

Fixing of Composite Polymer Disc insulators with hardware for 11 KV 45 KN “T&C” type (as per latest specification and drawings adopted and approved by NIGAM)

Erection of 11 KV Danger plate of size 200 X 250 mm complete in all respect

Fixing of PG clamps (Weasel to Weasel) made of aluminum alloy as per IS:617-1994 . All ferrous metal part intended for outdoor use except those made of stainless steel shall be protected by hot dip galvanizing in accordance with IS 2633-1986(latest amended)

Erection of M.S. Nuts & Bolts (Galvanized) of assorted size

Description of Work / Item(s)

Total price of Suppy (BoQ1/Schedule-1)

Total price of Erection (BoQ2/Schedule-2)

LASER POWER & INFRA PRIVATE LIMITED

Jakson Limited

Montecarlo Limited

Vijai Electricals Limited

LASER POWER & INFRA PRIVATE LIMITED

Jakson Limited

Vijai Electricals Limited

Montecarlo Limited

LASER POWER & INFRA PRIVATE LIMITED

Jakson Limited

Vijai Electricals Limited

Montecarlo Limited