Providing Sewerage system to Jubbal Town in NP Jubbal in Tehsil Jubbal Distt Shimla HP SH Construction of a protective sub-shed to safeguard the compressor motor and pump of the air diffuser as well as the sludge drying bed filtrate recycle pump from

Steel work welded in built up sections, trusses and framed work, including cutting ,hoisting ,fixing in position and applying a priming coat of red lead paint. including carriage of material within all leads and lifts and and as per direction of Engineer-in-charge.

Providing ridges or hips 60 cm over all in plain and gables, eaves board /facia with pre painted plain G.l. sheet fixed J or L hooks bolts and nuts 8mm dia Gl limpet and bitumen washers complete. (0.47 mm thick Gl sheet)

Providing and fixing Pre painted C.G.l.Sheet roofing fixed with galvanized iron J or L hooks bolts and nuts 8mm dia with between G.I. Lampet washers with Gl limpet washers filled with while lead complete excluding the cost of rafters and trusses 0.47mm thick sheet ( TATA/JINDAL)150mm dia

Providing & fixing Lab Sink fire-clay, white glazed, size 600x450x250 mm, ISI marked, including CI/MS brackets, cutting of counter, sealing with silicone, and making good, complete.

Providing & fixing Waste Coupling 40 mm CP brass

Providing & fixing Bottle Trap 32 mm CP brass

Providing & fixing PVC Waste Pipe 50 mm dia from trap to gully trap (ISI marked)

Providing & fixing Pillar Cock CP brass 15 mm heavy duty

Providing & fixing Bib Cock CP brass 15 mm (long body with nozzle)

Providing & fixing Angle Valve CP brass 15 mm

Providing & fixing Flexible Connectors SS braided 450 mm

Providing & fixing PPR Pipe 15 mm dia with fittings from nearest point incl. clamps, unions, making good etc.

Providing & fixing Acid/Chemical resistant ceramic tiles of approved make, size 200×200×10 mm (or equivalent ISl) on counter/dado, laid over acid-resistant mortar bed (as per manufacturer's spec.), joints filled with chemical resistant grout, including surface preparation, setting, curing, cleaning & finishing complete as per direction and entire satisfaction of Engineer-in-Charge.

Providing and laying Finolex PVC pipe IS marked over RCC slab for drainage of rainwater, including all fittings, supports & labour complete as per the direction and entire satisfaction of Engineer-in-Charge.

Laying, butt welding and testing of ISI marked steel tubes plain ended in trenches of following dia as per IS 1239-2001, including jointing the pipes with butt welding at both the ends according to relevant BIS standards/approved specifications including manufacturing reducers/tapers, all short pices and bends as per site requirement and made from parent tubes ( to be measurer and paid alongwith pipes. Bends shall be manufactured in such a way that not more than 111/4 degree deflection is caused by a single cut and internal dia is not reduced including hydraulic testing to the entire satisfaction of Engineer. in-charge. The damaged portion of galvanization due welding shall be provided with anticorrosive treatment by providing two coats of bituminous paint over priming coat as per AWWA specification C-203-1978. (Earth work to be measure & paid for separately).

Providing and fixing Glass Shelf of size (approx. 12" width x required length) made of 10-12 mm thick toughened glass, fixed with M.S. angle brackets, including drilling, fixing with rawl plugs, screws, etc., complete in all respeets as per satisfaction of Engineer-in-Charge.

Half Brick masonary using common burnt clay building bricks above plinth upto floor two level in cm 1:4(1cement:4sand)conventiohal brick first class:

15 mm thick cement plaster on fair sides of brick/stone masonery convrete walls for interior plastering upto floor two level including arises internal rounded angles not exceeding 80mm girth in cm 1:4 (1cement:6sand)

Providing form work with steel plates 3.15mm thick so as to give fair finish I/c centering shuttering propping etc. height of propping below supporting floor to ceiling not exceeding 4mt. Height & removal of same in situ reinforce ment concrete and plain concrete work in :-

Flat surfaces such as soffits of suspended floor roofs landing & like floor sqm etc., upto 200mm thickness.

Providing mild steel/tor steel reinforcement I/c bending binding and placing in position complete

Providing & laying CC 1:1.5:3 1cement:1.5 sand 3 graded aggregates 20mm nominal size curing complete excluding cost of form work & reinforcement for RCC,work in:-

in suspended floor roofs landing shalves & their support balconies,beams, girders bressumers cantilevers upto floor two level

Cutting in earth work and disposal of excavated earth in all leads and lifts in all kinds of soils, including dressing of sides, ramming of bottoms, stacking of serviceable material and disposal of unserviceable material complete in all respects as per the direction of Engineer-in-Charge.

Excavation in earth work in all kind of soil stacking excavated soil in the plinth sides of foundation and then disposing of all surplus soil in all leads & lifts as directed by Engineer in Charge.

P/L CC 1:3:6 1cement:3 sand:6 graded aggregates 20mm nominal size cum curing complete excluding cost of form work infoundation & plinth

Providing and fixing 19 mm thick factory-pressed BWP (Marine) Grade plywood (IS:710) for fabrication of tables, counters, cabinets, etc., including cutting, fixing with screws/adhesive, and finishing complete as per manufacturers specifications and direction of Engineer-in-Charge.

Providing and fixing High Pressure Laminate (HPL) Sheet / Sunmica of approved colour, make and minimum thickness 0.8 mm, bonded with synthetic resin adhesive conforming to I5:851-1978, over substrate, including cutting, finishing and polishing edges, complete as per manufacturer's specifications and direction of the Engineer-in-Charge. (Non-Schedule Item - Market rate to be adopted)

Providing and fixing Heavy-type soft-closing telescopic drawer channels (ball-bearing) of approved make, 500 mm long, including screws, complete as per direction.

Providing and fixing Stainless Steel Pull Handle (SS 304 grade), 4 inch (~100-102 mm) length, of approved make and finish (Satin/Brushed), including supply of matching stainless steel screws/fixtures, positioning, drilling (if required), fixing, alignment, and cleaning, complete as per manufacturer's specifications and as directed by the Engineer-in-Charge.

Providing and fixing PVC Edge Banding Tape (Lipping) 16-19 mm wide, 2 mm thick, hot-pressed over edges using edge-banding machine, complete as per direction.

Please Enable Macros to View BoQ information