Rehabilitation, Improvement and Basic Facility of Upper Wardha Dam in Amravati district of Maharashtra under DRIP-II (civil, mechanical, electrical and instrumentation work

Amount

CIVIL WORK

Sub Estimate :- 1) Resurfacing of Approch Road to Upper Wardha Dam ( Dum Top), Section Office and Left Bank Head Regulator

Item No.1 : Cleaning cutting thorny shrubs bushes , grass as directed with 15 M. lead and lift up to 1.5 M.

Item No.2 :Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing to proper grade and camber, applying and brooming requisite type of screening /binding Material to fill up the interstices of coarse aggregate, watering and compacting with vibratory roller to the required density by Mechanical Means Grading II (Using Screening Type B (11.2 mm Aggregate).

Item No.3: Providing and constructing 75 mm thick Modified Penetration Macadam (MPM) road surface including supplying all materials, preparing the existing road surface, spreading 40mm stone metal layers, 100 % crusher broken metal obtained by blasting) heating and spraying the bulk bitumen of specified grade @ 2 Kg/Sq.m, spreading 12mm size chips compacting with three wheel static roller having weight 8 to 10 M.T. to achieve the desired degree of compaction as per Technical specification clause 506 etc complete . Including picking out existing WBM surface. (VG-30 bulk bitumen rates are considered to arrive at rates.) Power roster on existing bitumen surface including tack code 0.5kg per sq. m. Etc. complete.

Item No.4: Providing and applying tack coat on the prepared surface heating by flames in Boiler and spraying bitumen with sprayer on Granular surface treated with primer @ 2.70 kg./10 Sq.M. (VG-30 bulk bitumen considered to arrive at rates)

Item No.5: Open Graded Premix Surfacing -Providing and Laying OGC 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates premixed with bituminous binder transported to site with VTS, laid over a previously prepared surface , finishing to the required grade , level, alignment ,and rolling to achieve the desired compaction but excluding prime/tack and seal coat. For Bitumen of specified grade using drum mix type hot mix plant with SCADA, Paver and Vibratory Roller (over BT Surface) (VG-30 bulk bitumen rates are considered to arrive at rates.)

Item No.6 : 9 MM SEAL COAT Providing and laying of Type A 9 mm Premix Seal coat with HMP of appropriate capacity crushed stone chipping 6.7 mm size and penetration bitumen of specified grade @ 1.28 kg/sq.m. preparing existing road surface by mechanical means , spreading chips, and rolling by static roller having weight 8 to 10 M.T. etc complete (VG- 30 bulk bitumen rates are considered to arrive at rates.) on black toped surface by using 0.09 cum per 10sqm of crusher aggregates passing through prescribed sieves and 0.012MT quantity of bitumen per 10 sq.m. Including supplying all material preparing the existing road surface heating bitumen and aggregate in hot mix plant laying the mix seal surfacing by paver finisher and compaction by power roller etc. complete. Using 60/70 grade bitumen.

Item No.7 : Supplying hard murum / kankar at the road side, including conveying and stacking complete.

Item No.8 :Spreading hard murum/soft murum / gravel or kankar for side width etc. complete.

Item No.9 :Compacting the hard murum side widths including laying in layers on each side with vibratory roller including artificial watering etc complete.

Sub Estimate :- 2) Cleaning of Vertical Porous Drains of Upper Wardha Dam.

Item No10 : Providing and supplying skilled Fitter/Foreman for removing and fixing stainless steel pipes of V.P.D.

Item No.11 : Cleaning by re drilling the vertical plum bob pipe including removing of cleaning material, grout material if any inside of the V.P.D. etc complete with all leads & lifts.

A) From 0 to 5 M.

B) From 5 to 10 M.

C) From 10 to 15 M.

D) From 15 to 20 M.

E) From 20 to 25 M.

F) From 25 to 28 M.

Sub Estimate :- 3) Construction of Lavatory Block at Upper Wardha Dam, section office @ Simbhora Tq. Morshi, Dist. Amravati.

Item No.12 : Excavation for foundation in earth, soils of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50 meters beyond the building area and stacking and spreading as directed, dewatering, repairing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift from 1.5m to 3.0 m) By Mechanical Means.

Item No.13 : Providing and laying cast in situ/Ready Mix cement concrete in M-10 of trap/ granite/quartzite/gneiss metal for foundation and bedding including bailing out water, steel centering, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing if required and curing complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum type mixer/concrete batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand/Crushed sand VSI Grade Finely washed etc.)

Item No.14 : Providing and laying in situ/Ready Mix Cement Concrete M-20 of Trap/granite/quartzite/gneiss metal for R.C.C. work in foundations like raft, strip foundation, grillage and footing of R.C.C. Columns and steel Stanchions etc. including bailing out water, steel centering formwork, laying/pumping cover blocks, compaction and curing roughening the surface if special finish is to be provided (Excluding reinforcement and structural steel) etc. complete, with fully automatic micro processor based PLC with SCADA enabled Reversible Drum type mixer/concrete Batch mix plant (Pan Mixer) etc. complete. With fine aggregate (Natural Sand/Crushed Sand VSI Grade washed etc.)

Item No.15 : Providing and laying cast in situ/Ready Mix cement concrete in M-20 of trap/ granite/quartzite/gneiss metal Metal for RCC columns as per detailed designs and drawing or as directed including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel) with fully automatic micro processor based PLC with SCADA enabled reversible drum type mixer/Concrete batch mix plant (PAN mixer) etc. complete. With fine aggregate (natural sand/Crushed sand VSI Grade finely washed etc.)

Item No.16 : Providing & laying cast in situ/Ready Mix C. C. M-20 of trap/granite/quartzite/gneiss metal for RCC beam and lintels as per detailed design and drawing, steel centering, formwork, cover blocks, laying/pumping, compacting, curing, finishing and roughening them to form surface with C.M. 1:3 of sufficient minimum thickness to give smooth and even surface roughening them if special finish is to be provided and curing complete (Excluding reinforcement and structural steel) with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Pan Mixer) etc. complete. With fine aggregate (Natural Sand/Crushed sand VSI Grade finely washed etc.)

Item No.17 : Providing & Laying cast in situ/ready Mix CC M-20 of trap/granite/gneiss metal for RCC Chajja as per detailed design and drawing including steel centering, formwork, cover blocks, laying/pumping, compacting and roughening the surface if special finish is to be provided and curing complete.

Item No.18 : Providing & laying cast in situ/Ready Mix C. C. M-20 of trap/granite/quartzite/gneiss metal for RCC slabs and landing as per detailed designs and drawing including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete, ( Excluding reinforcement and structural steel) With fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Pan Mixer) etc. complete. With fine aggregate (Natural Sand/Crushed sand VSI Grade finely washed etc.)

Item No.19 : Providing and fixing in position TMT-FE-50 bar reinforcement of various diameters for RCC pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas lintels pardis, copings, fins, arches etc. as per detailed designs, drawing and schedules. Including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete.

Item No.20 : Providing second class burnt brick masonry with conventional/IS Type bricks in cement mortar 1:6 in foundations and plinth of inner walls/in plinth external walls including bailing out water manually, striking joints on unexposed faces, raking out joints on exposed faces and watering etc. complete.

Item No.21 : Providing second class burnt brick masonry with conventional/IS Type bricks in cement mortar 1:6 in superstructure including striking joints, raking out joints, watering and scaffolding etc. complete.

Item No.22 : Providing second class burnt brick masonry with conventional/I.S. type bricks in cement mortar 1:4 in half bricks wall including mild steel longitudinal reinforcement of 2 bars of 6mm diameter/2 hoop iron strips 25 mm x 1.6 mm placed at every third course, properly bent and bonded at ends scaffolding, racking out joints and watering etc. complete.

Item No.23 : Providing and fixing M-40 grade thick vibrated pull cast or similar type concrete frame with chamfer conforming to I.S. 65241983 having 6 mm dia bars 3 Nos. and strips @ 250 mm C/c and fixing in wall with 6 nos. of hold fast of 12mm dia bars 500 mm long including primer and oil painting etc. complete) frame size 60 mm x 125 mm.

Item No.24 : Providing and fixing solid core flush door shutter commercial in single leaf 32 mm thick without ventilator commercial type of exterior grade as per detailed drawings with wrought iron hold fast, stainless steel fixtures and fastenings and handles on both sides and finishing with oil painting 3 coat complete.

Item No.25 : Providing and fixing steel ventilator fully glazed partly fixed as per detailed drawing with hot dip zinc coating including fabricating glazing with plain/obscured glass pans 5mm thick and approved type quality and iron oxidized fixtures and fastening with guard square bars 12 mm 10 cm c/c and oil painting 2 coats etc. complete.

Item No.26 : Providing and fixing mild steel grill work for windows, ventilators etc.20kg sq.m. as per drawing including fixtures necessary welding and painting with one coats of anticorrosive paint and two coats of oil painting complete.

Item No.27 : Providing internal cement plaster 12 mm thick in single coats in cement mortar 1:4 without neeru finish, to concrete, brick, surface, in all positions including scaffolding and curing etc. complete.

Item No.28 : Providing sand faced plaster externally in cement mortar using approved screened sand in all position including base of 15mm thick in cement mortar 1:4 using waterproofing compound at 1 kg per cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8mm thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etc. complete.

Item No.29 : Providing and laying matt finish ceramic tiles of having size 30 cm x 30 cm confirming to IS 15622/2006 (group D II-A ) and 7 to 8 mm thick for flooring in required position laid on a bed of 1:4 cement mortar including cement float , joint with white/color cement slurry cleaning curing etc. com

Item No.30 : Providing and laying Antiskid Ceramic tiles of approved quality of size 30cm. X 30cm. And Confirming to IS 15622-2006 (Group -B IIA) for antiskid flooring in required position laid on a bed of 1:4 cement etc. complete.

Item No.31 : Providing and fixing 1st class white glazed earthenware Orissa Type W.C. Pan 580 mm. dia including P or S trap cast iron soil and vent pipe up to the outside face of the wall (1:5:1) CC bedding 15 mm thick 10 liter PVC flushing cistern with all necessary pipe connection etc. complete.

Item No.32 : Providing and fixing white Glazed Earthenware squatting plate (Ladies Urinal) with PVC flushing cistern of 5 liters capacity with fitting, inlet pipes and stop tap, brackets for fixing the cistern, 32 mm dia. P.V.C. flush pipe with fitting and flushing arrangement including lead soil pipe lead trap, soil pipe connection up to the outside face of the wall.

Item No.33 : Providing and fixing White glazed earthenware full stall type Urinal with PVC flushing cistern of 5 liters capacity with fitting, inlet pipes and stop tap brackets for fixing the cistern 32 mm dia. PVC flush pipe with fitting and flushing arrangement including lead soil pipe, lead trap soil pipe connection up to the outside face of the wall.

Item No.34 : Providing and fixing White glazed earthenware wash hand basin of 55cm x 40cm size including cold water pillar tap/cold and hot water pillar tap brackets, rubber plugs and brass chain stop tap and necessary pipe connections including PVC waste pipe and trap up to the outside face of the wall making good the damaged surface testing etc. complete.

Item No.35 : Providing, laying and fixing PVC pipe of 110 mm dia. With fitting such as bends, tees, reducers, clamps etc. including necessary excavation, trench filling etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD choky or as directed etc. complete.

Item No.36 : Providing and fixing 100 mm dia stabilizer pipe/PVC soil vent/waste pipe and with necessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc. complete.

Item No.37 : Providing and fixing HDP container syntax or alike one piece molded water tank made out of low density polythyler and built corrugation including of delivery up to destination hoisting and fixing of accessories such as inlet, outlet overflow of all tanks capacity above 200 to 1000 liters.

Item No.38 : Providing and constructing brick masonry inspection chamber 60 cm x 45 cm with RCC raft in B.C. soil area including cost of reinforcement, 1:2:4 cement concrete channels half round GSW pipes, brick masonry, plastering from inside and airtight with 75 mm thick RCC cover medium duty 100 kg. etc. complete

Item No.39 : Providing and fixing reinforced cement concrete cover of size 60mm. X 45 mm. with frame over inspection chamber etc. complete. Medium duty (140kg).

Item No.40 : Providing, laying and fixing PVC pipe of 25 mm dia. With fitting such as bends, tees, reducers, clamps etc. including necessary excavation, trench filling etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD choky or as directed etc. complete.

Item No.41 : Providing, laying and fixing PVC pipe of 15mm dia with fitting such as bends, tees, reducers, clamps, etc. including necessary excavation, trench filling etc. complete.

Item No.42 : Providing, laying and fixing PVC pipe of 20mm dia with fitting such as bends, tees, reducers, clamps, etc. including necessary excavation, trench filling etc. complete. Including existing pipe line if necessary and conveying and stacking the same in PWD choky or as directed etc. complete.

Item No.43 : Providing, laying and fixing PVC pipe of 75mm dia with fitting such as bends, tees, reducers, clamps, etc. including necessary excavation, trench filling etc. complete. Including existing pipe line if necessary and conveying and stacking the same in PWD choky or as directed etc. complete.

Item No.44 : Providing, laying and fixing PVC pipe of 32 mm dia. With fitting such as bends, tees, reducers, clamps etc. including necessary excavation, trench filling etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD choky or as directed etc. complete.

Item No.45 : Providing and fixing C. P. Pillar cock long neck with aerator of approved make including necessary sockets/union nut etc. complete.

Item No.46 : Providing in plinth and floors with contractors material/brought from outside and approved by engineer in charge in layers of 15 cm to 20 cm including watering and compaction etc. complete.

Item No.47 : Providing dry/trap/granite/quartzite/gneiss rubble stone soiling 15 cm to 20 cm thick including hand packing and compacting etc. complete.

Item No.48 : Providing soling using 80 mm size trap metal in 15 cm. layer including filling voids with Crushed sand/grit, ramming watering etc. complete.

Item No.49 : Providing soak pit of sizwe120 cm x 120 cm including excavating and filling with brick-bats.

Item No.50 : Providing & fixing 10 cm PVC nahani trap with grating etc. complete.

Item No.51 : Providing and applying plastic emulsion paint of approved quality, color and shade to old and new surfaces in two coats including scaffolding, preparing the surface. (Excluding the primer coat) etc. complete.

Item No.52 : Providing and applying two coats of exterior acrylic emulsion paint confirming to corresponding I. S. of approved manufacture and of approved color to the plastered surfaces including cleaning, preparing the plaster surface, applying primer coat, scaffolding if necessary, and watering the surface for two days etc. complete.

Sub Estimate :- 4) Estimate for Construction of Rest room at Upper Wardha Dam Section Office@ Simbhora Tq. Morshi, Dist. Amravati.

Item No.53 : Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50 m beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift up to 1.5 m.) By Manual Means

Item No.54 : Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50 m beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift up to 1.5 m.) By Manual Means

Item No.55 : Providing and laying in situ cement concrete M­20 of trap / granite /quartzite/ gneiss metal for R.C.C. work in foundations like raft, strip foundations, grillage and footings of R.C.C. columns and steel stanchions etc. including bailing out water, formwork, cover blocks compaction and curing roughening the surface if special finish is to be provided (Excluding reinforcement and structural steel) etc. etc. complete, reversible drum type concrete mixer. Etc. complete. With natural sand/V.S.I. quality Artificial Sand. Bd.F.3 Page No. 298 and B.7, Page No.38

Item No.56 : Providing and casting in situ cement concrete M­20 of trap /granite /quartzite/ gneiss metal for R.C.C. columns as per detailed designs and drawing or as directed including centering, formwork, cover blocks compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel). Reversible drum type concrete mixer etc. complete. With natural sand/V.S.I. quality Artificial Sand

Ground Floor

First Floor

Item No.57 : Providing and laying Cast in situ/Ready Mix cement concrete M-20 of trap / granite /quartzite/ gneiss metal for R.C.C. beams and lintels as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/pumping, compaction and roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel). With fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed etc)

Ground Floor

First Floor

Item No.58 : Providing and laying Cast in situ/Ready Mix cement concrete M-20 of trap/ granite / quartzite/ gneiss metal for R.C.C. slabs and landings as per detailed designs and drawings including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed etc)

Ground Floor

First Floor

Item No.59 : Providing and laying Cast in situ/Ready Mix cement concrete M-20 of trap/ granite/ quartzite/ gneiss metal for R.C.C. chajja as per detailed design and drawings including steel centering, formwork, cover blocks, laying/pumping, compacting and roughening the surface if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel). With fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed etc)

Ground Floor

First Floor

Item No.60 : Providing second class Burnt Brick masonry with conventional/ I.S. type bricks in cement mortar 1:6 in foundations and plinth of inner walls/ in plinth external walls including bailing out water manually , striking joints on unexposed faces, raking out joints on exposed faces and watering etc. Complete.

Item No.61 : Providing second class Burnt Brick masonry with conventional/ I.S. type bricks in cement mortar 1:6 in superstructure including striking joints, raking out joints, watering and scaffolding etc. Complete

Ground Floor

First Floor

Item No.62 : Providing and fixing in position TMT / HYSD steel bars reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams and columns, canopies, staircases, newels, chajjas, lintels, pardies, coping, fins, arches etc. as per detailed design and drawings and schedules including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required completed.

Ground Floor

First Floor

Item No.63 : Providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15 mm thick in cement mortar 1:4 using waterproofing compound at 1 kg per cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8 mm thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etc. complete.

Ground Floor

First Floor

Item No.64 : Providing and applying two coats of water proof cement paint of approved manufacture and of approved color to old plastered surfaces including scaffolding if necessary, cleaning and preparing the surface, watering for two days etc. complete.

Ground Floor

First Floor

Item No.65 : Providing internal cement plaster 12mm thick in single coat in cement mortar 1:4 without neeru finish to concrete or brick surfaces, in all positions including scaffolding and curing etc. complete.

Ground Floor

First Floor

Item No.66 : Providing and applying Two coats of wall care Putty on plastered surface and Ceiling and Walls to prepare surface even and smooth of approved make, etc complete.

Ground Floor

First Floor

Item No.67 : Providing and applying pearl/ luster finish paint of approved color and shade to the existing plaster surface including scaffolding, preparing the surface, applying the acrylic wall putty etc. complete.

Ground Floor

First Floor

Item No.68 : Providing and fixing Orissa type color glazed earthenware 625 x 450 mm. w.c. pan including trap, C.I. soil and vent pipe up to the outside face of wall including 100mm. dia. C.I. plug, bend,15mm.thick10litrePVC flushing cistern with all necessary pipe connection etc. complete.

Ground Floor

First Floor

Item No.69 : Providing and fixing mild steel grill work for windows, ventilators etc. 20 kg/sq.m. As per drawing including fixtures, necessary welding and painting with one coats of anticorrosive paint and two coats of oil painting complete. For Grill of 20kg / Sq.m.

Ground Floor

First Floor

Item No.70 : Providing and fixing Colored glazed with bottle trap earthenware Wash Hand Basin of 55x40 cm. size including cold water pillar taps, brackets, rubber plugs and brass chain, stop tap, chromium plate bottle trap and necessary pipe connections including UPAC waste pipe and trap up to the outside face of the wall, making good the damaged surface, testing etc. complete.

Ground Floor

First Floor

Item No.71 : Providing sills of required material 20mm to 25mm thick, on a bed of cement mortar 1:4 including cement float, filling joints with neat cement slurry, curing, polishing, rounding edges, cleaning complete.b)Granite

Ground Floor

First Floor

Item No.72 : Providing and fixing M40 grade thick vibrated pull cast or similar type concrete frame with chamfer conforming to I.S. 65241983 having 6 mm dia. bars 3 Nos. And stirrups @250 mm c/c and fixing in wall with 6 Nos. of hold fast of 12 mm dia bars 500 mm long including primer and oil painting etc, complete) frame size 60 mm x 100 mm .

Ground Floor

First Floor

Item No.73 : Providing neeru finish top plastered surfaces in all positions including scaffolding and curing etc. complete.( Item No.32.21 P. No. 225 )

Ground Floor

First Floor

Item No.74 : Providing and laying vitrified matt finish tiles having size 590 mm to 605 mm x to 605 mm of 8 to 10 mm thickness and confirming IS. 15622-2006 (Group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and cleaning etc. complete. a) Flooring.

Ground Floor

First Floor

Item No.75 : Providing and laying ceramic tiles of having size 30 cm. x 30 cm. and confirming to corresponding I.S. for dado and skirting in required position with readymade adhesive mortar of approved quality on plaster of 1:2 cement mortars including joint filling with white/ color cement slurry cleaning curing etc. complete.

Ground Floor

First Floor

Item No.76 : Providing and fixing frame with / without ventilator of size as specified with Country cut teak wood for doors and windows including chamfering, rounding, rebating, iron holdfast of size 300mm x 40mm x 5mm with oil painting, etc. complete

Ground Floor

Item No.77 : Providing and fixing Country cut teak wood double or single leaf second class fully paneled door shutter with 35mm thick style and rail with 25 mm thick panels with open able fan light as per detailed drawings. Excluding the door frame 60mm x 100mm stainless steel fixtures and fastening and finishing the wood work with oil painting 3 coats. (Excluding the door frame).

(A ) Full Item Rate

Item No.78 : Providing and constructing Brick Masonry Inspection Chamber 60cm x 45cm x 90cm including 1:4:8 cement concrete foundation 1:2:4 cement concrete channels half round G.S.W. pipes, Brick Masonry, plastering from inside and with frame fixed in cement concrete with R.C.C. Cover medium duty 140 kg with frame etc complete.

Item No.79 : Providing and fixing H.D.P container Syntax or alike one piece molded water tank made out of high density polythyler and built corrugated inclusive of delivery up to destination hoisting and fixing of accessories such as inlet, outlet overflow pipe inclusive of all tanks capacity between 200 to 1000 liters

Item No.80 : The shutter should be of bearing bottom 40 x 18 x 1.25 mm at weight 0.417 kg/Rmt. Inter locking section 40 x 18 x 1.10 mm at weight 0.469 kg/Rmt. and handle and top section 40 x 18 x 1.25 mm at weight o.417 kg/Rmt. As per detailed drawings and as directed by Engineer in charge with all necessary Aluminum sections fixtures and fastenings such as roller bearing in nylon casting and self locking catch fitted in vertical section of shutter including 5 mm thick plain glass and aluminum mosquito net shutter with stainless steel jail with all required screws and nuts etc, complete. With color Anodizing with box

Ground Floor

First Floor

Item No.81 : Providing and fixing in position powder coated aluminum louvered windows / ventilator of various sizes with powder coating as per detailed drawing and specifications including aluminum frames 80 x 38 mm x 1.22 mm box type, 5 mm thick sheet glass louvers, of approved quality etc. complete.

Ground Floor

First Floor

Item No.82 : Providing and fixing 30mm thick SOLID PANEL PVC INTERNAL DOOR SHUTTER consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 40mm x 20mm for stiles ,top, lock and bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame shall be covered with 5mm thick heat molded PVC channel of size 30 x 100mm forming stiles, and 5mm thick, 125mm wide PVC sheets for top rail, lock rail and bottom rail on either side, and 15mm (5mm x 3) thick, 20mm wide cross PVC sheet as gap insert for top rail and bottom rail. Paneling of 10 mm thick prelim PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles and rails with 30mm wide x 5mm thick PVC sheet beading on either side, and joined together with solvent cement adhesive etc. An additional 5mm thick PVC strip of 20mm width is to be stuck on the interior side of the C Channel using PVC solvent cement adhesive. Including stainless steel fixtures and fastening Complete as per direction of Engineer in charge, manufacturer's specification and drawing.

Ground Floor

First Floor

Item No.83 : Providing and fixing false ceiling of 15mm thick as per drawings including powder coated G.I. wall angle of 20mm x 20mm x 0.60 mm size, G.I. grid runners of size 15mm x 38 mm at 600mm center to center both ways and suspended using G.I. 3mm wire including fixing using butterfly clip sand fasteners including transporting, scaffolding all necessary labor and machinery, finishing etc. complete.

Ground Floor

First Floor

Item No.84 : Providing and laying ceramic tiles of having size30cmx30cm confirming to I. S.15622/2006 (group DII-A) and 7 to 8 mm thick for flooring in required position laid on a bed of 1:4 cement mortar including cement float, filling joint with white/ color cement slurry cleaning curing etc. complete.

Ground Floor

First Floor

Item No.85 : Providing and applying two coats of lead /zinc base oil paint / bituminous paint of approved color and shade to old wood work and fiber boards previously painted including if necessary scaffolding , preparing the surface excluding priming coat etc. Complete.

Ground Floor

First Floor

Item No.86 : Providing and fixing 40mm diameter and 1.5 mm thick Stainless steel hand railing in S.S.304 Grade including fabricating ,fixtures, erecting, necessary welding, grinding, finishing, buffing to stainless steel pipe etc. complete

Item No.87 : Providing and applying Water Proofing Treatment using Acrylic Polymer modified cement based water proofing coating with fiber glass mesh mixing at the rate of powder to liquid (2:1) by weight covering 9 to 10 sq.m. /kg with two coat using approved chemicals for masonry and concrete surface by brush covering 7 years guarantee on Stamp Papers etc. complete

Ground Floor

Item No.88 : Providing and fixing Sofa set 3 +1 + 1 Brown and cream leather Dimension Length 182.50 cms, Weight 66 Kg. seating capacity five seats

Item No.89 : Providing and fixing of Tea Table 900 mm x 750 mm x 450 mm with 12 mm thick Color Etched Tempered glass with beveled Drawing made out of 18 mm thick water proofing ply. The outer laces to be finished with high quality 4 mm thick veneer or 1 mm thick mica etc.

Item No.90 : Providing and fixing single bed of size 2025 L x 1000 D x 650 H with mattresses and pillow. Understructure - The legs are made of square tube of size 25 x 25 mm made out of M.S. with a thickness of 1.2 mm. The legs should have corner brackets welded to it at two levels. The corner brackets are made of 2 mm thick CRCA having a L shaped structure to join the side panels and headboard to the leg. Three nos of Horizontal stiffeners are provided at equal intervals. The stiffeners are made of square tube of size 25 x 25 mm made out of M.S. with a thickness of 1.2 mm. The middle Horizontal Stiffener has a attached to it to transfer the load to the ground and add to the strength and stability of the complete structure. This leg is also made of square tube of size 25 x 25 mm made out of M.S. with a thickness of 1.2 mm. All Metal components to undergo 7 tank treatment process and should be powder coated to the thickness of minimum 50 microns DFT. The side panels are made up of 18 mm thick prelim Particle board with both side decorative laminate. All exposed edges are sealed with 2 mm thick PVC edge Banding. The overall width of the side panel is 150 mm. The side panels have 18 mm thick prelim particle board Baton running for required length to add rigidity to the structure. The head board is made up of 18 mm thick prelim particle board with both side decorative laminate. All exposed edges are sealed with 2 mm thick PVC edge Banding. The head board size to be considered as 1000 x 450 mm. The bed base is made up of 12 mm thick Prelim particle board with both side White laminate.

Item No.91 : Providing and fixing Wardrobe with mirror of size 900 L x 600 D x 1965 H. The wardrobe side panels and doors are made up of 18 mm thick prelim particle board with both side decorative laminate. All exposed edges are sealed with 2 mm thick PVC edge Banding. The shelves are made of 18 mm thick prelim particle board with decorative laminate on both sides. The top is made of 36 mm prelim particle board with decorative laminate on both sides. (18 mm prelim particle board and 18 mm batons so all sides to achieve 36 mm overall thickness). The exposed edges of the top are sealed with 2 mm thick PVC edge Banding. The top most part of the wardrobe has an aluminum hanger rod of EBCO make. One drawer of size 400 W x 150 H x 450 D made of 18 mm thick prelim particle board has been considered. The drawer will have a multipurpose lock of EBCO premium make. The wardrobe handles are satin SS finish of 160 mm pitch. All hinges considered are Hettich make. Necessary good quality hardware’s have been considered as required.

Item No.92 : Providing and fixing on walls/ ceiling/ floors, 15 mm dia. heavy grade having embossed as ISI Mark galvanized iron pipes weight of 1.48 Kg/meter with necessary fittings. Remaking well the demolished portion and applying primer of anti-corrosive oil paint 2 coats Including necessary scaffolding and removing existing pipe line if necessary and conveying and stacking the same in PWD choky or as directed etc. complete.

Ground Floor For 15 mm

Ground Floor For 25 mm

First Floor For 20 mm

Item No.93 : Providing, laying and fixing P.V.C. pipe of 110 mm. dia. with fittings such as bends, tees, reducers, clamps, etc. including necessary excavation, trench filling etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD choky or as directed etc. complete..

Ground Floor For 15 mm

First Floor For 20 mm

Item No.94 : Providing and fixing 15 mm dia. screw down bib/ stop tap of brass including necessary socket union nut complete

Ground Floor

First Floor

Item No.95 : Providing and fixing push cock (Self closing tap) symet type of 15 mm dia. including necessary socket, testing etc. complete.

Ground Floor

First Floor

Item No.96 : Providing and constructing granite kitchen platform with fixing of stainless steel sink 600 mm x 450 mm size as per detailed drawing including vertical both side polished kadappah stone 25 to 30 mm thick supports with kadappah top 35 to 40 mm thick and polished granite 16 to 20 mm top with side strips of granite at front and both sides of platform raised with two vertical granite supports 15 cm height and top granite of 75 x 40 cm including cutting, opening for sink of required size in kadappah as well as granite etc. complete. (Platform top size 5.00 m x 0.60 m and height is 0.75 m)

Ground Floor

Item No.97 : Providing and fixing 15 cm rigid PVC Nahani trap including PVC grating ,bend, connecting piece of UPVC pipe up to the outside face of wall ,making the good damaged surface and testing etc. complete ( Prior approval of sample and brand by Ex. Engr. is necessary before use)

Ground Floor

First Floor

Item No.98 : Providing and fixing 15cm x 10cm salt glazed stoneware gully trap in cement concrete 1:4:8 outside the building including cast iron grating in the sink, connecting glazed stoneware pipe, brick masonry chamber with cast iron lid and cast iron grating for the gully trap

Ground Floor

First Floor

Item No.99 : Providing and fixing Water Pump of 1.00 HP including installing, etc complete

Ground Floor

Sub Estimate :- 5) Construction of Barbed wire fencing and chain link fencing for protection of Upper Wardha Dam.

Item No.100 : Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50 m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift up to 1.5 m.) By Mechanical means

Item No.101 : Providing & laying in the cement concrete in M-10 of trap/granite quartzite/gneiss metal for foundation and bedding including bailing out water, plywood /steel, formwork, compacting, roughening them if special finish is to be provided, finishing if required and curing complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc complete. With fine aggregate ( Natural sand / crushed sand VSI Grade finely washed etc )

Item No.102 : Providing and laying Cast in situ/Ready Mix cement concrete M-15 of trap/ granite/quartzite/gneiss metal for bed blocks , foundation and such other items including bailing out water, steel centering, formwork, laying / pumping, compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc complete. The cement mortar 1:3 plaster is considered for rending uneven and honeycombed surface only. Newly laid concrete shall be covered by gunny bag, plastic tarpaulin etc (Wooden centering will not be allowed) with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etc complete. With fine aggregate (Natural sand/ Crushed sand VSI Grade finely washed etc )

Item No.103 : Providing and erecting 1.50 M. high wire fencing with seven rows of barbed wire supported on M.S. angles (50 mm x 50 mm x 6 mm) at 2.5 meters centre to centre including excavating pits for foundation, fixing posts in cement concrete of 1:4:8 of size 45 x 45 x 45 cm, fastening the wire and painting the M.S. Angles with one coat of red lead primer and two coats of painting etc complete.

Item No.104 : Providing & erecting chain link fencing 1.6 M. height with G.I. Chain link of size 50 x 50 mm, 8 gauge thick and fixed 75 mm above ground level on vertical M.S. Angles of 40 x 40 x 6 mm size, including excavating pits for foundation and embedded in C.C. block of 1:4:8 mix of size 450 x 450 x 670 mm. at 1.75 M. C/C with iron bar 16 mm dia as hold fast including welding link with angle frame at 30 cm c/c with nuts and bolts and horizontal M.S. Angles at top and bottom of size 25 x 25 x 5 mm size and vertical M.S/ flat 35 x 5 mm and 25 mm horizontal including cross support of 40 x 40 x 6 mm angles both side at every corner or bend embedded in concrete blocks of 1:4:8 of size 450 x 450 x 670 mm including 3 coats of oil painting etc complete.

Item No.105 : Providing and fixing mild steel grill gate with angle iron frame 65 x 65 x 10 mm with iron bars at 150 mm c/c and diagonal flats as per the detailed drawing including hinges, pivot block locking arrangement, welding riveting and oil painting of three coats of approved shade weight of gate 35 Kg/Rmt.

Sub Estimate : 6) Repairs to Stair Case of Lift Cum Staircase Well of UPPER WARDHA DAM..

Item No.106 : Rising of folding to reach the entire surface area of bridge. upto10 m height above ground level, made with MS tube, horizontal and vertical tub joint with cup and lock system with MS tubes, challis, MS clamp and maintain it in a serviceable condition for execution work of cleaning and/ or pointing and or/applying protection coating and/ inspection of work at required locations and removing it there after etc complete. (Item includes making of temporary support for scaffolding, cost of scaffolding, labor, material, safety devices, etc .,all complete)

Item No.107 : Removing rich mix cement concrete including stacking the spoil as directed with all leads, lifts etc, complete.

Item No.108 : Providing & Applying chemical for cleaning the exposed steel structure, TMT bars, etc. of structure by grinding the surface by grinder machine, wire brush, removing existing corrosion from the metal also removing loose particles, of the area by water jet, (using other mechanical / manual means) and apply on prepared surface of Dura Guard- as corrosion preventive coat on prepared TMT bars, steel structure ,metal surface etc. to protect it from corrosion etc. as per manufacturer's specification ( using other manual / mechanical means) after that Providing and applying high abrasive resistant, self curing, UV resistant, impermeable ,high strength, non shrink, Poly Ironite Ceramic Cementations (PICC) repair mortar resurfacing on concrete surface of thickness up to 10 mm including breaking honey comb area, (using manual/mechanical means) , clean the concrete surface with special chemical clonon with pressure water jet for removing of algae fungi, apply bond coat Kelox water miscible epoxy before PICC application with all leads and lifts, Material, Machinery, labor, scaffolding, etc. complete as per specification and as directed by engineer-in-charge.

Item No.109 : Drilling 32 mm dia hole and up to depth of 400 mm and grouting with epoxy resin of reinforcement steel of 25 mm dia of all manpower and equipments complete in all respect

Item No.110 : Providing and fixing in position TMT / HYSD steel bars reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams and columns, canopies, staircases, newels, chajjas, lintels, pardies, coping, fins, arches etc. as per detailed design and drawings and schedules including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required completed.

Item No.111 : Providing filling of Micro-concrete and 10 mm aggregate ( 1:1) including sacrificial leak proof MS shuttering includes the cost of hire charges of all machineries, barge, boat, cost of all tools and all labor charges etc., complete.

Item No.112 : Providing rough cast cement plaster externally in two coats to concrete, brick or stone masonry surfaces in all positions with base coat of 12 to 15 mm thick in C.M. 1:4 and rough cast treatment 12mm thick in proportion 1:1 1/2:3 including scaffolding and fourteen days curing complete.

Item No.113 : Providing and applying two coats of water proof cement paint of approved manufacture and of approved color to the plastered surfaces including scaffolding if necessary, cleaning and preparing the surface, watering for two days etc. Complete.

Item No.114 : Removing cement tiles, or marble or polished Shahabad floor or dado without bed concrete including stacking the materials as directed with all leads, lifts etc. complete

Item No.115 : Providing and laying Antiskid Ceramic tiles of approved quality of size 30 cm x 30 cm and confirming to IS 15622-2006 (Group-B IIA) for antiskid flooring in required position laid on a bed of 1:4 cement mortar including cement float, filling joint with cement slurry cleaning curing etc. complete.

Item No.116 : Removing iron pipe railing having wooden R.C.C. or C.C. or iron post and stacking the materials as directed etc. complete.

Item No.117 : Providing and Fixing mat finish stainless steel (of 302 grade ) railing with top pipe of 50 mm dia. and vertical pipe of 38 mm dia at 0.60 m c/c or as required and horizontal pipes of 25 mm dia in three rows, all pipes of 2 mm thick including buffing, fabricating fixtures and fastening including pipe base of appropriate diameter and ball base of 75 mm dia above newel post of 75 mm diameter etc. complete (Prior approval of sample and brand by Ex .Engineer is necessary before use)

Item No.118 : Providing and fixing collapsible steel gate in one / two leaves with hot rolled vertical channels of 18 x 9 x 3 mm minimum size, crossings of M.S. flats of size 18 x 5 mm T or E section for runner of minimum 40 x 6 mm size for flange, M.S. flat for top runner of minimum size 40 x 12 mm with roller wheels confirming to grade F.G. 150 fitted with snap headed rivets of minimum size 6 mm max. spacing of vertical channels be 100 mm enclosed gate position and clear space of 150 mm between two sets of crossings with hold fasts, stoppers, spaces, handles, locking arrangement and one coat of red lead primer and oil painting etc. complete. (I.S. 105211983). Including Removal of Old Collapsible Gate.

Item No.119 : Providing and applying two coats of flat oil paint of approved color and shade to internal / external plastered surfaces including scaffolding if necessary, cleaning and preparing the surface (excluding primer coat) etc. complete.

Sub Estimate :- 7)SURGING AND AIRJETTING OF RELIEF WELL ON D/S OF UPPERWARDHA DAM.

Item No.120 : Surging and air jetting of Relief well on D/S of earthen dam as per IS 50-50/1968 with all leads and lifts etc complete.

Item No.121 : Drilling 32mm diameter grout holes in concrete / rock by percussion drilling using jack hammer as directed to specified depth for consolidation / contact grouting including cost of all materials, machinery, labor, cleaning holes, ventilation, lightening, drainage and all other ancillary operations etc., complete

Item No.122 : Cleaning cutting thorny shrubs bushes, grass as directed with 15m lead and lift up to 1.5m.

Item No.123 : Providing and applying two coats of flat oil paint of approved colour and shade to internal/external plastered surfaces including scaffolding if necessary clearing and preparing surfaces excluding primer paint.

Item No.124 : Providing and fitting M.S. cover over Relief Well on D/S side

Sub Estimate :- 8) Repairs to Drainage System of Cross Drains & Longitudinal Drains.

Item No.125 : Cleaning cutting thorny shrubs bushes, grass as directed with 15m lead and lift up to 1.5m.

Item No.126 : Removing wet silt from canal bed with 15.00 meter. Lead and 1.50 meter. lift including depositing the excavated stuff as directed

Item No.127 : Providing and laying in situ cement concrete of grade M-25 of trap / granite / gneiss / quartzite / graded metal for RCC works of gallery, sluice, spillway crest, spillway downstream face, energy dissipating structures, intake structures, training walls, piers, abutments, slab etc. with Batching Plant and Transit mixer including shuttering and scaffolding, placing, compacting, curing etc. complete with an initial lead of 5 km. and lift of 1.5 m (A) M-25 (20 MSA) (Cement 7.62 bags/Cum).

Sub Estimate :- 9)Railing on D/S Left & Right Side Guide Walls Of Upper Wardha Dam.

Item No.128 : Drilling 32mm diameter grout holes in concrete / rock by percussion drilling using jack hammer as directed to specified depth for consolidation / contact grouting including cost of all materials, machinery, labor, cleaning holes, ventilation, lightening, drainage and all other ancillary operations etc., complete

Item No.129 : Providing and fixing in position TMT / HYSD steel bars reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams and columns, canopies, staircases, newels, chajjas, lintels, pardies, coping, fins, arches etc. as per detailed design and drawings and schedules including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required completed.

Item No.130 : Providing and laying in situ cement concrete of grade M-25 of trap / granite / gneiss / quartzite / graded metal for RCC works of gallery, sluice, spillway crest, spillway downstream face, energy dissipating structures, intake structures, training walls, piers, abutments, slab etc. with Batching Plant and Transit mixer including shuttering and scaffolding, placing, compacting, curing etc. complete with an initial lead of 5 km. and lift of 1.5 m. (A) M-25 (20 MSA) (Cement 7.62 bags/Cum)

Item No.131 : Providing and Fixing mat finish stainless steel (of 302 grade ) railing with top pipe of 50 mm dia. and vertical pipe of 38 mm dia at 0.60 m c/c or as required and horizontal pipes of 25 mm dia in three rows, all pipes of 2 mm thick including buffing, fabricating fixtures and fastening including pipe base of appropriate diameter and ball base of 75 mm dia above newel post of 75 mm diameter etc. complete (Prior approval of sample and brand by Ex. Engineer is necessary before use)

Sub Estimate : 10) Repairs to staircase from section office to dam top of Upper Wardha Dam.

Item No.132 : Removing cement tiles, or marble or polished Shahabad floor or dado without bed concrete including stacking the materials as directed with all leads, lifts etc. complete

Item No.133 : Providing and laying Antiskid Ceramic tiles of approved quality of size 30 cm x 30 cm and confirming to IS 15622-2006 (Group-B IIA) for antiskid flooring in required position laid on a bed of 1:4 cement mortar including cement float, filling joint with cement slurry cleaning curing etc. complete.

Item No.134 : Providing rough cast cement plaster externally in two coats to concrete, brick or stone masonry surfaces in all positions with base coat of 12 to 15 mm thick in C.M. 1:4 and rough cast treatment 12mm thick in proportion 1:1 1/2:3 including scaffolding and fourteen days curing complete.

Item No.135 : Providing and laying cast in situ /Ready Mix cement concrete in M-15 of trap/granite/quartzite/gneiss metal for bed blocks, foundation blocks and such other items including bailing out water, steel centering, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc complete. The Cement Mortar 1: 3 plaster is considered for rendering uneven and honeycombed surface only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.) with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batching plant (Pan Mixer) etc. complete. With fine aggregates (Crushed sand VSI Grade)

Item No.136 : Providing and laying cast in situ /Ready Mix cement concrete in M-15 of trap/granite/quartzite/gneiss metal for bed blocks, foundation blocks and such other items including bailing out water, steel centering, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc complete. The Cement Mortar 1: 3 plaster is considered for rendering uneven and honeycombed surface only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.) with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batching plant (Pan Mixer) etc. complete. With fine aggregates (Crushed sand VSI Grade)

B PART II MECHANICAL WORKS

Sub Estimate :- 1) Strengthening to the Approach Bridge of Gallery by Embedding Beam inside the Stone Masonry for 15X12 M Radial Gate-13 Nos. @ Upper Wardha Project under Executive Engineer, Upper Wardha Dam Division, Amravati

Item No.137 : Dismantling of Pipe of Size 300 mm Dia. and 200 mm Dia. Fitted onApproach Bridge for Gallery @ Upper Wardha Project under ExecutiveEngineer,UpperDamDivision, Amravati...(AsperRA-1)

Item No.138 : Dismantling of Railing and Other structure and Refitting of the Samewhich includes pipe of 40 mm dia., MS Angle 75x75x8 mm, curting etc. ofApproachBridgefor Gallery@Upper Wardha Project..(RA-2)

Item No.139 : Manufacturing and Erection of Grating of size 6800x1160 mm forApproach Bridge for Gallery @ Upper Wardha Project under ExecutiveEngineer,UpperDamDivision, Amravati…..(Asper RA-3)

Item No.140 : Embedding Beams inside the Stone Masonry by Drilling and Stacking ofMaterial at Workplace for Strengthening of Approach Bridge of Gallery @UpperWardhaProject...(Asper RA-4)

Item No.141 : Providing Strengthening to the Approach Bridge for Gallery whichincludes ISMB 200x100 mm and MS Angle 75x75x8 mm for SupportingStructuretoGrating@ Upper WardhaProject.(As RA-5)…

Item No.142 : Transportation Charges..... (As per RA-6)

C) PART - III ___Hydro-electrical WORKS

Sub Estimate :- 1) Providing Lightening Arrestor at Upper Wardha Project (Nal Damayanti dam) Tal.: Morshi Dist. Amravati

Item No.143:-Supply, Erection, and Testing& Commissioning of Advanced EarlyStreamer Emission (ESE) Type of Lighting Arrestor of covering a radius of110 meter for level 3 protection. When mounted at a height of 5 meteraboveterracefloor level,Havingtriggeringtime63microseconds. Lightning air terminal should be totally autonomous device. It is designedto work on positively as well as negatively charged cloud conditions. Theinternal triggering circuitry & electronics should contain ambient electricfield sensor, charge accumulator, command & HV amplifier, transformer& triggering release. It is designed as per NFC 17-102 & IEC 60-1:1989. TheESE terminal should be tested by CPRI for the Impulse current of 40 kA(8/20 micro sec) with 5 positive & 5 negative impulse. with followingspecification of current capacity≥200 KA(10/35µs) ,capacity against windspeed ≥40 m/s, dimension 39cm,lower diameter of ESE terminal shouldbe 30.5 cm , weight=4 kg. The ESE Lightning Arrestor should be tested inMSME along with 2 digit transient counter with display digit from 0 to 99for a minimum of count impulse of > 1 kA (8/20 m sec) with degree ofprotectionof IP20withthree earthingelectrodeof1m.length ingrid

Sub Estimate : 2) Providing High Mast at Upper Wardha Project (Nal Damayanti Dam) Tal.: Morshi Dist. Amravati

Item No.144 : Supplying and erecting 16 m (clear height) High Mast (Top-150 mm,Bottom- 410mm) with lowering and rising motorized unit, lanterncarriage assembly suitable for max. 12 nos. luminaries and its control gearbox, lightning finial arrangement for fixing aviation light and foundationboltsonprovidedfoundationasperspecificationno. OH-PL/HM(excludingluminaries).

Item No.145 : Making M- 20 cement concrete foundation by considering the safe soilbearing capacity at site as 10 T/sq. m at 2 m depth including excavationand fixing provided nut bolts with the help of template, duly plastered asperdesigncomplete(for 16mraisingloweringhighmast).

Item No.146 : Supplying and erecting LED flood light fitting of 150W, including lamp,with PF > 0.95,class IP 65 and above housing of pressure die castaluminum alloy and heat sink extruded aluminum complete as perspecificationNoFG-ODF/FLS-2

Item No.147: Supplying and erecting Outdoor Stand Mounted Feeder Pillarfor high mast of the same manufacturer with 63A TPN MCB incomer,single dial timer switch, 45A TP contactor for automatic switching ofluminaries, 2 no’s 9A contactors and raise/lower push button, andprovision for termination of adequate size of incoming and outgoingcables erected in min. 14 SWG CRCA sheet box powder coated withsupporting angles, self-lock, gasket and slanting top erected with CCfoundationcomplete.

Item No.148 : Supplying, erecting & terminating XLPE armored cable 4 core 10 sq.mm.aluminum conductorwithcontinuous5.48sq.mm.(12SWG)G.I. earth wire complete erected with glands & lugs, on wall/trusses/pole orlaidinprovided trench/ pipeasperspecificationno.CB-LT/AL

Item No.149 : Supplying and laying (including excavation of suitable width & depth upto 90 cm) 50 mm outside dia. double wall corrugated pipes (DWC) ofHDPE for enclosing cable below ground/road surface, to required depthcomplete.

Item No.150 : Providing pipe type earthing with 40mm. dia. G.I. pipe or 20 mm dia. G.I.Rodcompletewithallmaterialsas perspecificationno.EAEP

Sub Estimate :- 3)Supply , Erection , Testing & Commissioning of Nal Damayanti Dam Gallery Lighting at Upper Wardha Project, Dist : Amravati

Item No.151 : Supplying and erecting LED street light fitting 12 to 18 W, with PF > 0.95class IP 65 and above housing of pressure dia cast aluminum alloy andheat sink extruded aluminum complete as per specification No FG-ODF/FLS-2.

Item No.152 : Supplying, erecting & terminating XLPE armored cable 4 core 10sq. mm.aluminum conductor with continuous 5.48 sq. mm. (12 SWG) G.I. earthwire complete erected with glands & lugs, on wall/ trusses/pole or laid inprovidedtrench/pipeasper specificationno. CB-LT/AL

Item No.153 : Supplying, erecting & terminating XLPE armored cable 4 core 4 sq. mm.aluminum conductor with continuous 5.48 sq. mm. (12 SWG) G.I. earthwire complete erected with glands & lugs, on wall/ trusses/pole or laid inprovidedtrench/pipeasper specificationno. CB-LT/AL

Item No.154 : Supplying & erecting mains with 2x1.5 sq.mm F.R copper PVC insulatedwire laid in provided conduit/trucking/inside pole/Bus bars or any otherplacesas per specificationNo:WGMA/BW

Item No.155 : Supplying and erecting UPVC reinforced flexible conduit 20 mm in dia.conforming to I.S. with required number of couplings, PVC bushes, checknuts etc.complete.

Item No.156 : Supplying and erecting triple pole metal clad HC type rewire able fuse andswitch 415, V 32A with neutral link on angle iron / GI frame as perspecificationno.SW-SWR/MTP.

Item No.157 : Supplying & erecting water tight terminal box of 1.6 mm (16 gauge) CRCAsheetof size150x100 x100mmcompleteonpole asper Specificationno.CB-SB

Item No.158 : Providing earthing with copper earth plate size 30 x 30 x 0.315 cmcomplete with all materials, testing & recording the results as perspecificationno.EA-EP

Item No.159 : Supplying and erecting iron, sheet metal work consisting of CRCA sheets,various sections of iron, plates, chequered plates, rods, bars, MS pipes,etc. for panel board or any other purpose with bending, cutting, drillingand welding complete erected at the position with necessary materialsduly paintedwith onecoatof red oxide and two coats of enamel paint to match the switchgears or as perdirectionsbythe authority

Item No.160 : Supplying and erecting metal work in CRCA sheet with fabrication ofboxes, panel boards, etc. including cutting, bending, drilling, welding,riveting, treated with anti-rust treatment and duly powder coated orpainted with one coat of red lead paint and 2 coats of enamel paintcomplete.

Item No.161 : Supplying & erecting PVC armored cable 4 core 6 sq mm aluminumconductor with continuous 5.48 sq mm (12 SWG) G.I. earth wirecomplete erected with glands & lugs, on wall/ trusses/pole or laid inprovidedtrench/pipeasper specificationno.CB-LT/AL

Item No.162 : Supplying and erecting Triple pole iron clad HC type rewire able fuse andswitch 415/ 500V 16A with neutral link on angle iron frame as perspecificationNo. SW-SWR/MTP

Sub Estimate : - 4) Providing Electric Wiring to New Rest Room & Lavatory Block @ Upper WardhaProject.

Item No.163 : Supplying and erecting UPVC reinforced flexible conduit 25 mm in dia. conforming to I.S. with required number of couplings, PVC bushes, check nuts etc. complete.RSJ

Item No.164 : Supplying and erecting PVC trunking (PVC casing-capping) of size 32 mm with accessories on wall/ceiling as per specification No: WG-MA/CON.

Item No.165 : Supplying and erecting PVC trunking (PVC casing-capping) of size 40 mm with accessories on wall/ceiling as per specification No: WG-MA/CON.

Item No.166 : Supplying & erecting mains with 2x1.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WGMA/ BW

Item No.167 : Supplying & erecting mains with 1x1.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WGMA/ BW

Item No.168 : Supplying & erecting mains with 2x2.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit / trunking / inside pole/Bus bars or any other places. as per specification No: WGMA/ BW

Item No.169 : Supplying & erecting mains with 2x4 sq.mm F.R copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places. as per specification No: WGMA/ BW

Item No.170 : Supplying, erecting & terminating XLPE armored cable 2 core 10 sq. mm. aluminum conductor with continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Item No.171 : Supplying and erecting ISI mark modular type switch 6A / 10A duly erected on provided plate and box with wiring connections complete.

Item No.172 : Supplying and erecting ISI mark modular type switch 16A duly erected on provided plate and box with wiring connections complete.

Item No.173 : Supplying and erecting ISI mark modular type 3 pin 6A multi sockets with safety shutter, duly erected on provided plate and box with wiring connections complete.

Item No.174 : Supplying and erecting ISI mark modular type 3 pin 6 / 16A multi socket with safety shutter, duly erected on provided plate and box with wiring connections complete.

Item No.175 : Supplying and erecting ISI mark modular type bell-push 6A / 10A duly erected on provided plate and box with wiring connections complete.

Item No.176 : Supplying and erecting ISI mark modular type (two module) electronic step regulator for fan, duly erected on provided plate and box with wiring connections complete.

Item No.177 : Supplying and erecting PVC Surface modular switch box with double mounting plate for 3 modules duly erected.

Item No.178 : Supplying and erecting PVC Surface modular switch box with double mounting plate for 6 modules duly erected.

Item No.179 : Supplying and erecting PVC Surface modular switch box with double mounting plate for 12 modules duly erected.

Item No.180 : Wiring for plug on board with Modular type Switch socket, copper wiring and earthing as per specification No: WG-PW/SW

Item No.181 : Point wiring in PVC trunking (casing-capping) with 1.5 sq.mm (2+1E) FRLSH grade copper wire, modular type switch, earthing and required accessories as per specification No: WG-PW/SW

Item No.182 : Supplying and erecting ding dong / electronic musical type call bell with heavy duty coil suitable to operate on 230V A.C. supply erected on polished double wooden block/sun mica block of suitable size

Item No.183 : Supplying and erecting double pole metal clad switch with HC type fuse 240V, 63A on iron / GI frame as per specification no. SW-SWR/MDP.

Item No.184 : Supplying, erecting & marking SPMCB 6A to 32A, C-series (for motor/power) in provided distribution board as per specification no. SW-SWR/MCB

Item No.185 : Supplying, erecting & marking SPMCB 6A to 32A, B- series (for lighting) in provided distribution board as per specification no. SWSWR/ MCB

Item No.186 : Supplying erecting and marking double pole isolator only switch version of miniature circuit breaker of 40A with required wiring connections and lugs etc. in provided distribution board complete.

Item No.187 : Supplying and erecting single pole and neutral distribution board (SPNDB) with door surface/flush mounted with 2 ways for incoming and 10 ways for outgoing SP MCB’s on iron/ GI frame as per specification no. SW-SWR/MCBDB

Item No.188 : Supplying and erecting single pole and neutral distribution board (SPNDB) with door surface/flush mounted with 2 ways for incoming and 10 ways for outgoing SP MCB’s on iron/ GI frame as per specification no. SW-SWR/MCBDB

Item No.189 : Providing pipe type earthing with 40mm. dia. G.I. pipe or 20 mm dia. G. I. Rod complete with all materials as per specification no. EAEP

Item No.190 : Supplying and erecting LED Street light fitting suitable for above 40W to 48W lamp, including lamp, with PF > 0.95 class IP 65 and above housing of pressure die cast aluminum alloy and heat sink extruded aluminum complete per specification No. FGODF/FLS2.

Item No.191 : Supplying and erecting street light Wall bracket made from 40 mm. dia ‘B’ class G.I. pipe 1.2 m in total length complete as per specification no. FG-BKT/WB

Item No.192 : Supplying & erecting 10-12W, 230V integral type LED Lamp suitable for B-22/E-27 base.

Item No.193 : Supplying and erecting regular/ standard model ceiling fan of 1400mm. sweep complete erected in position as per specification no. FG-FN/CF

Item No.194 : Supplying and erecting fan hook box of 10 mm M.S. round bar bounded to the R.C.C. bars up to 50 mm length each side and pierced through a 16 S.W.G. thick aluminum / M.S. Bowl 100 mm dia. or equivalent square size and having depth up to 75 mm complete erected with duly painted by one coat of red oxide paint and two coats of paint erected in position and without any leakage of slurry of cement concrete on either side of the box and positioned to the bottom level of the slab.

Item No.195 : Supplying & erecting LED 20W tube light fitting (4 feet) with aluminum housing, heat sink, integrated HF electronic driver complete.

Item No.196 : Supplying & erecting mains with 2x2.5 sq.mm. and earth wire 1.5 sq.mm FRLSH PVC copper wire in HMS PVC conduit min. 20mm dia. as per specification No: WG-MA/PC.

Item No.197 : Supplying, erecting & marking SPMCB 0.5A to 5A in provided distribution board as per specification no. SW-SWR/MCB

Item No.198 : Supplying and erecting PVC Surface modular switch box with double mounting plate for 1 module complete duly erected.

Item No.199 : Making trench of suitable width and depth in soft soil for laying provided LT cable up to and including16 sq.mm complete as per specification no. CW-EXN-CTR

Item No.200 : Supplying and erecting storage type horizontal / vertical water heater 25 liters capacity with BEE 5 star rating high impact resistance engineering plastic body on wall / loft complete duly tested and marking sr. no. and date of erection. Specification no. AP-WH/STWH

Item No.201 : Supplying, installing, testing and commissioning split type variable speed Inverter technology room Air conditioning unit 1.5 TR capacity having ISEER minimum 4.50 suitable to operate on250V, 50 cycles, A.C. supply having 1 no of air handling unit hi wall / floor mounting type complete with refrigerant R410 A/R32 and copper condenser at position. Specification no. APAC/ SAC

Item No.202 : Supplying and erecting fresh air cum exhaust fan of light duty 250 V A.C. 50 cycles 300mm. 1400 RPM rust proof body & blades, wire mesh, duly erected in an approved manner.

Item No.203 : Providing recess in brick wall suitable for erection of exhaust fan up to 450 mm sweep complete with grouting of nut, bolts, plaster in hand color washing to match the color of the wall for the wall thickness of 150 mm.

Item No.204 : Supplying and erecting iron, sheet metal work consisting of CRCA sheets, various sections of iron, plates, chequerred plates, rods, bars, MS pipes, etc. for panel board or any other purpose with bending, cutting, drilling and welding complete erected at the position with necessary materials duly painted with one coat of red oxide and two coats of enamel paint to match the switchgears or as per directions by the authority.

D) PART - IV Instrumentation

Sub Estimate :- 1) Dismantling the existing Piezometer, cleaning the hole of existing Piezometer and Providing a Casagranda type Piezometer in a drilled hole with all its required accessories of Upper Wardha Dam.

Item No.205 : Providing a Casagranda type Piezometer in a drilled hole with all its required accessories as per IS- 7356 part-1 at the project site with all material transportation etc complete.

A) Providing 37 mm dia. 6 mm wall thick and 60 cm long porous tube piezometer with stopper and top adapter made up of carborendum with porous tube filter of grain size 60 micron as specified in IS 7356 part-I

B) Providing PVC riser pipe of 12 mm outer dia 1.5 mm wall thickness and 1.5 M. long.

C) Providing PVC socket for riser pipe joint.

D) Providing 12 mm brass hexagonal pipe top cap.

E) Providing 50 mm dia. And 1.25 M. long G.I. pipe casing protective cover.

F) Providing 150 mm dia and 1.20 M. deep well graded sand filter around casagrande piezometer.

G) Providing 150 mm dia. And 1.0 M. deep bentonite clay plug above sand filter.

H) Providing Drilling of Bore hole of 150 mm diameter in soft strata in Dam Body with all required material for installation of piezometer.

Item No.206 : Providing electronic water level indicator for taking water level reading in casagrande piezometer with stainless steel probe and marked flexible tape of 200 M. length.

Sub Estimate :- 2) Supplying, Installing and commissioning Instruments at Upper Wardha Dam ( Pan Evaporometer, Autographic Water Level Recorder, Standard Rain gauge station, Dry/Wet Bulb Thermometer )

Item No.207 : Supplying, Installing and commissioning of Pan Evaparometer on site asper specifications mention in HIS Manual and IS code (5973-1970)excludingall taxesetccomplete asdirected byEngineer Incharge.

Item No.208 : Supplying,Installing and commissioning of Autographic Water Level Recorder (AWRL) with complete as directed by EngineerIncharge, Assemblies on site as per specifications mention in HIS manual and IS code(9116-1979)excluding all taxes etc complete as directed by Engineer Incharge.

Item No.209 : Supplying , installingand commissioning of Standard Rain Gauge Stationson site as per specifications mention in HIS manual and IS code ( 5225-1992) excluding all taxes etc and complete as directed by Engineer In-charge.

Item No.210 : Supplying, Installing and Commissioning ofDry Bulb Thermometer onsitesas per specifications excluding all taxes etc and as directed byEngineer-In-Charge.

Item No.211 : Supplying, Installing and Commissioning ofWetBulb Thermometer onsites as per specifications excluding all taxes etc and as directed byEngineer-In-Charge

Sub Estimate :- 3) Providing, fixing, installation and commissioning of additional IP Based Digital Remote Surveillance System & Accessories @ Upper Wardha Dam

Item No.212 : Supply of High quality IP Day-night Bullet Camera for IP Based RemoteSurveillance System with minimum Specifications -1/3" Sensor,3.0Megapixel,1080P,IRBullet,IRDistance30to50m,PoE,On vif,WDR, 3.3~12mm VarifocalIRCorrectedLens,etc. complete.

Item No.213 : Supply of High quality Metal Box along with lock & key & Weather proofHousing with required brackets & accessories such as stand2 nos., Pole mount clamps bracketsand misc. hardware as & if required forfitting & installation of IP Cameras of IP Based Remote SurveillanceSystemetc. complete.

Item No.214 : Supply of High quality essential equipments, accessories & componentssuch as 12 VDC Inventor kit for Camera, 12 V Power supply, 12V to 5VPower Supply DC to DC OR 5V Power Supply, 12 VDCInventor kit , 6 AMPSurge Protector,80 AH Battery, Media converter 100/1000 MBPS 2 no’s foreach camera, Patch cod for media converter (FC) as & if requiredforinstallation & commissioning of IP Camera of IP Based RemoteSurveillance System etc. complete.

Item No.215 : Supply of High quality 8 Channel 1 SATA PortNetwork Video RecorderNVR (Hardware Network Video Recorder) for IP based digital RemoteSurveillance System

Item No.216 : Supply of High quality Automatic Voltage Regulated ( AVR ) basedUninterrupted Power Supply ( UPS 550 VA ) with 130 AH Battery & essentialequipments, accessories & components such as 12 VPower supply, 12Vto 5V Power Supply DC to DC OR 5V Power Supply, 6 AMP Surge Protector,HDMI/VGACable5/ 15Metersas& if requiredfor installation& functioningofIP CameraofIP BasedRemote Surveillance System during shortperiodof powercutetc.

Item No.217 : Supply of Surveillance Recording & Storage Unit / AV type Hard Disk Drive( SRS / AV HDD ) for Remote Surveillance System for Video/Audiorecordingstoragecapacityofminimum1 TB(TetraByte)

Item No.218 : Supply of High quality Metal box along with lock & key in control roomwith required accessories such as Switch 16/8/5 port, stand, clamps,brackets misc. hardware etc. as & if required for protection ofIP BasedRemote SurveillanceSystemNVRetc. complete

Item No.219 : Supply of DC Video power supply for IP based digital Remote SurveillanceSystem Cameras

Item No.220 : Supply of Enclosure box for Pbased digital Remote Surveillance System Cameras

Item No.221 : Supply of RJ 45 Connector for IP based digital Remote SurveillanceSystem Cameras

Item No.222 : Supply of P.V.C. pipe 63 mm with required accessories & misc. hardware as & if required for IP based digital Remote Surveillance system.

Item No.223 : Supply of FR grade, PVC armored multimode Optical Fiber Cable with 6 fibers, with core dia. µm, suitable for 1 GB ps Ethernet distance at 850 nm of wavelength or to laid in provided pipe/trench for IP Based Remote Surveillance System as per site requirement etc complete.

Item No.224 : Supply of Remote Surveillance System CCTV or 4 + 1 or LAN or 2 coreservice cable for fitting on wall/ceiling or to laid in provided pipe/trenchforIPBased Remote SurveillanceSystem as persiterequirement etc. complete.

Item No.225 : Supply of Misc Hardware, accessories, &materialas per onsiterequirement for fitting, installation & commissioning of IPBased RemoteSurveillance Systemetc. complete.

Item No.226 : Providing / giving on site consultation along with technical support fordetermining locations & quantities of various types of Cameras & systemforthe effective implementation of total surveillanc esystem(i.e.for coverage of maximum are aunder surveillance system)forthe satisfactory Commissioning of the system etc complete.

Item No.227 : Providing, fixing, Installation & Commissioning, with onsite testing &training (One time immediately after commissioning, for any number ofpersons)forthe IPBasedRemoteSurveillanceSystemetc. complete.

Item No.228 : Providing / giving on site services including required programmingalong withSoftware, Hardware &Technical suppor tfor the whole system for the satisfactory commissioning of the system etc. complete.

Item No.229 : Providing / giving as & when required on site or online services againstany manufacturing defects only, ( within Period of 1st year startingfromthe date of Satisfactory installation & commissioning ) with requiredsoftwareandhardwaresupportforthewholesystemforthesatisfactory working of the system etc. complete. Email of intimationletter should be sent by the customer immediately after breakdown ormis-functioning of the system or any part their off. We will attend the callmaximum within 48 hrs from the receipt of call in normal conditions, butin case of any unavoidable circumstances viz. strikes, due to naturalatmospheric conditions,nonavaiblityof transportetc.orduetoanyother reasons it may vary according to the current situation at that time.On attending the call our representative will repot the nature & cause ofproblem to the concern authority by sms/Email. If possible he / the teamwill try to resolve the problem immediately. But if it is impossible then hewill report the concern authority & will sent the demerged part / systemto the concern service station / manufacturing company for repairs underwarranty & will reinstall the same after repairs. If at any stage it is foundthat the part / system is not covered under warranty due to any reasonwe will inform & quote you accordingly by sms / email & after yourwrittenacceptancewewillget itrepair &reinstall.