REPAIR AND MAINT OF JCOs ORs MD ACCN INCLUDING ELECTRICAL MAINT IN MAP ACCN AND APS UNDER AGE BR II OF GE WEST MATHURA

Amount

Taking down cement plaster on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water etc. complete all as specified and directed.

Demolition of brick work or stone/boulders masonary, built in cement mortor including all quoins, arches pillars, etc but excluding ashlar facing dressed stone work and precast concrete articles complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing rubbish off premises complete all as specified and directed.

Demolition of cement (un-reinforced) concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed by Engineer-in-Charge.

Demolition of cement concrete (un-reinforced) in ground floor and paving not exc 15 cm thickness (below or above ground level.) & removing unserviceable materials in low laying area, complete, all as directed by Engr-in-Charge.

Taking down chowkhats with shutter (without taking off shutters from the frame) area not exc. 1.50 Sqm each complete all as specified and directed.

Taking down chowkhats with shutter (without taking off shutters from the frame) area exc. 1.50 Sqm but n.exc 4.00 sqm each complete all as specified and directed.

Taking down shutters of any description exc 1 Sqm and not exc. 2 Sqm each complete all as specified and as directed by Engineer-in-charge.

Dismantling of wall and ceiling boards of any type and any thickness including cover fillets complete all as specified and directed.

M&L for Brick work with sub class ‘B’ old size burnt bricks, straight or curved on plan exc 6m mean radius built in cement mortar (1:6) complete all as specified and directed by Engineer-in-charge.

S&F Pressed steel frame for doors of size 105 x 60 mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc complete all as specified and directed.

M&L for cement concrete type C-1, (1:3:6) using 20mm graded aggregate as in bed block or filling of chowkhats including necessary form work complete all as specified and directed.

M&L 35mm thick factory made glazed and skeleton shutters of 2nd class HW with partially panel shutter open rebated and prepared to receive glass / gauze etc edges or framing plain chamfered or rounded fitted with cut or mitred beads for securing glass etc as specified in SSR Part-1 section 8.24 (a) complete all as specified and directed.

S&F for 30mm thick flush shutter solid core construction with block board core & ply wood face panels, commercial type on both faces complete all as specified and directed by Engineer-in-charge.

S&F for 25mm thick flush shutter solid core construction with block board core & ply wood face panels, commercial type on both faces complete all as specified and directed by Engineer-in-charge.

S&F factory made solid PVC door frame of size 50mm x 47mm made out of 5mm thick plain colour PVC sheet reinforced with MS square tube complete all as specified & shown in relevant drawing of item No. 08095 in MES Schedule (Part-II) and directed by Engineer-in-Charge.

S&F 30mm thick factory made solid core PVC door shutter (style) consisting of frame made out of mild steel tubes for top and bottom rails, mild steel frame shall be covered with heat moulded plain colour PVC sheet, 'C' channel having PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail and bottom rail; panelling of plain colour PVC sheet to be fitted in mild steel frame welded/ sealed to the styles and rails with suitable PVC sheet beading and joined together with solvent cement, complete, all as specified & shown in relevant drawing of item No. 08080 in MES Schedule (Part-II) and directed by Engineer-in-Charge.

S&F 100mm long stainless steel Butt hinges fixed complete all as specified and directed.

S&F 150mm stainless steel barrel tower bolts with bright bolt and fixed complete all as specified and directed.

S&F 150mm long stainless steel handles, oval type complete all as specified and directed.

S&F 125 mm aluminium anodised Hasp and staple, safety type with mild steel hinge pin including bolt to hinge plate (ISI marked) complete all as specified and directed by Engineer-in-charge.

S&F 100mm size mild steel butt hinges cold rolled medium weight (ISI marked) complete all as specified & directed by Engineer-in-Charge.

S&F 300mm mild steel (Helical door spring) ordinary rat tail rod pattrern spring including roller and roller plate complete with necessary welding work complete all as specified and directed.

S&F 300mm long aluminium alloy anodised sliding door bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy (ISI marked) complete all as specified & directed by Engineer-in-Charge.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or stainless steel wire staples complete all as specified and directed by Engineer-in-Charge.

S&F in repairs stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or stainless steel wire staples complete all as specified and directed by Engineer-in-Charge.

Hacking out old broken glass any thickness, size, quality or description from wooden / metal frame and punching or drilling out old glazing pins/spring clips complete all as specified and directed by Engineer-in-charge.

M&L 3mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces, complete all as specified and as directed.

M&L 3mm thick figured glass pin head type and glazing with oil putty in square not exc 0.5 sqm in each pane complete all as specified and directed by Engineer-in-charge.

S&F 1st class softwood beads, straight (any size) for glazed or gauzed joinery, renewed, including miters etc, and removing old beads to stone all as specified and directed.

M&L for 25mm thick PCC (1:2:4) type B-0 using 12.5mm graded stone aggregate ) as in floor finishes and leveling course complete all as specified and directed.

M&L for glazed ceramic tiles (coloured) 450mm x 300mm x 7mm thick on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick rendering in cement & sand mortar (1:4) including necesary cutting as per site requirment complete all as specified and directed by Engineer-in-charge.

M&L Non skid coloured ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but n.exc 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match with and including 15mm thick screed bed in cement mortar (1:6) for laying floor finishes complete all as specified and as directed.

M&L for vitrified ceramic tiles light shade 8-9mm thick (square/ rectangular) polished area of each tile not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick cement screed bed in CM (1:4) complete all as specified and directed.

All as per item No 34.00 (here-in-before) above but as in skirting over 10mm thick backing coat in CM (1:3) complete all as specified and directed.

M&L for machine cut Kota stone slab flooring 18 to 20mm thick (minimum size 550mm x 550mm or size as directed) laid over & including screed bed or bedding layer of 20mm thick in CM (1:6) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed by Engineer-in-charge.

M&L for machine cut Kota stone slab 18 to 20mm thick (minimum size 550mm x 100mm or size as directed), on vertical surfaces such as dado, skirting, raiser of steps etc. laid over & including rendering 10mm thick in CM (1:4) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including cutting, grinding, rubbing and polishing complete all as specified and directed by Engineer-in-charge.

M&L for 18-20mm thick Granite (of any type) work (table rubbed and polished) for Shelves (veneering to wall) including 15mm thick plaster in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed.

M&L for 15mm thick rendering in two layer on fair faces of brick masonry or concrete surfaces of walls consisting of 1st layer of 10mm thick plaster in CM 1:6 and 2nd layer (setting coat or top layer) of 5 mm thick plaster in CM 1:4 mixed with water proofing compound (ISI marked) as per manufacturer’s instructions, finished fair & even, complete, all as specified. Note : - Supply only water proofing compound shall be measured and paid for separately.

M&L for rendering 5mm thick in CM (1:4) as on ceiling complete all as specified and directed.

M&L rendering 15 mm thick in CM 1:6 on brick masonry surfaces or on other than fair faces of brick masonry finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

Supply only liquid water proofing compound ISI marked complete all as specified and directed by Engineer-in-charge

M&L for 75 mm thick PCC (1:3:6) type C-2 using 40 mm graded crushed stone aggregate as in plinth protection, finished fair and even complete all as specified and directed by Engineer-in-charge. Note :- Plinth protection shall be laid to slope (1 in 30) in bays not exceeding 3 metre in length and joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with sealing compound grade B. Cost of ceiling compund is included in the unit rate of this item complete all as spcified and directed.

M&L for applying a coat of two component elastomeric acrylic polymer modified cementitious water proofing coating, having properties of 80 % elongation as per ASTM D412, resisting 5 bars hyrostatic pressure as per DIN 1048, reduction to rapid chloride shall be 70 as per DIN 1048, crack bridging upto 1.2mm as per ASTM 4548.5. The mixing ratio of the coating shall be 2 parts of powder & 1 part of liquid without any water addition in the mixing, etc., complete as per manufacturers specifications and sprinkle sand at 10-15 gram per sqft for better grip with plaster complete all as specified and directed.

Taking up or down 15mm dia, steel tubing & connections including cleaning for refixing or removal to store complete all as specified and directed by Engineer-in-Charge.

Taking up or down 20mm dia, steel tubing & connections including cleaning for refixing or removal to store complete all as specified and directed by Engineer-in-Charge.

S&F 15 mm dia steel water tubing, galvanized, medium grade, with all fittings, fixed to walls and ceiling or in floor complete all as specified and directed by Engineer-in-Charge

S&F 20 mm dia steel water tubing, galvanized, medium grade, with all fittings, fixed to walls and ceiling or in floor complete all as specified and directed by Engineer-in-Charge

Fixing only 15mm bore old galvanised steel water tubing including cleaning with & including new fittings and fixed complete to walls and ceilings or laid in floors in new or old position complete all as specified and directed by Engineer-in-charge. Note: GI tubing retrieved vide item No 45.00 shall be used under this item.

Fixing only 20mm bore old galvanised steel water tubing including cleaning with & including new fittings and fixed complete to walls and ceilings or laid in floors in new or old position complete all as specified and directed by Engineer-in-charge. Note: GI tubing retrieved vide item No 46.00 shall be used under this item.

M&L for Cement concrete (1:5:10) type E-2 using 40mm graded stone aggregate as in sunken part of slab complete all as specified and directed.

M&L for treatment of sunken floor slab comprising of the following specifications with and including demolition of sunken floors complete all as specified and directed:- (i) Cleaning the sunken/lowered portion of \ RCC slab surface (incl vertical total depth plus skirting height) of floors by wire brush,chisel out any mortar sticking to the surface and brooming completely. Provn of 40 mm thick avg PCC 1:2:4 type B-O using 12.5mm graded aggregate as in padding concrete to achieve proper slope incl cutting holes in bricks or RCC wall for sprout. (ii) Rendering of uneven surfaces with 6mm thick CM 1:4 mixed with and incl integral water proofing compound Sika Plastocreat plus or equivalent make in Fosroc / Thermax as approved by GE @ 0.2% by wt of cement consumed incl filling it with water to check dampness and seepage and where dampness/seepage is noticed, nozzles shall be fixed and grouting carried out. Cont/-

Cont/- (iii) All junctions points of side wall where CI/GI/PVC pipes are passing through shall besealed with epoxy puttySikaguard 694 F(I) or equivalent make in Fosroc/Thermax as approved by GE (iv) After drying putty, wash the slab and sides of sunken portion with water and make it clear and clean (v) Applying two coats of polymer modified cementious water proof coating with Sika Topseal 107 or equivalent make in Fosroc/Thremax as approved by GE over base coat as per manufacturer's instruction to bottom and vertical sides upto finished floor level +100 mm height. The thickness of two layers shall be 1mm. When the second layer is still sticky, coarse sand spray shall be carried for the vetical and bottom surface of the sunken portion. Cont/-

Cont/- (vi) Plaster the bottom surface and sides up to bottom of the skirting with minimum 20mm thick CM 1:4 mixed with and incl integral water proofing compound Sika Plastocreat plus or equivalent make in Fosroc/Thermax as approved by GE @ 0.2% by wt of cement consumed as per manufacturer's specification incl rounding of corners and injuctions sloping towards spout. (vii) All pipes laid in sunken portion shall be covered with 50mm thick PCC 1:3:6 all round after painting with anticorrosive paint.

S &F for rotational moulded polythelene water tanks triple layer white colour (cylindrical vertical with closed top) hoisted and fixed in position for 2000 ltr. storage capacity including disconnecting and taking down old unserviceable tanks and ball valve complete all as specified and directed.

S &F for rotational moulded polythelene water tanks triple layer white colour (cylindrical vertical with closed top) hoisted and fixed in position for 750 ltr. storage capacity including disconnecting and taking down old unserviceable tanks and ball valve complete all as specified and directed.

S&F Ball brass valve, high pressure, with polythene float and flynut complete, screwed for iron pipe 20mm bore or brass ferrule and fixed complete all as specified and directed by Engineer-in-Charge.

S&F in repair Ball brass valve, high pressure, with polythene float and flynut complete, screwed for iron pipe 20mm bore or brass ferrule and fixed complete all as specified and directed by Engineer-in-Charge.

S&F in repair 20mm dia PTMT ball valve high Pressure with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed (min wt 142 gms) complete all as specified and directed.

S&F 100mm CI pipes soil, waste and vent pipe in any length with or without ears, with cement joints fixed to wall including applying a coat of black japaned paint on outer surface of pipes including taking down old unserviceable CI pipe and fittings complete all as specified and directed.

S&F 100mm bore cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified and as directed by Engineer-in-charge.

S&F PVC (SWR) 110 mm bore pipes single socketed in any length with rubber ring joints laid in trenches or fixed to wall complete including taking down old unserviceable PVC pipe with fittings complete all as specified and directed.

S&F PVC (SWR) 110mm bore bends any radius complete all as specified and directed.

S&F PVC (SWR) 110mm bore junction single, (Single T) equal or unequal complete all as specified and directed.

S&F in repairs 32mm bore CP waste coupling fittings for sinks, basins with long shanks and fly nuts, flange and bedded in red cement and fixed complete all as specified and directed by Eng-in-charge.

S&F in repairs 40mm bore CP waste coupling fittings for sinks, basins with long shanks and fly nuts, flange and bedded in red cement and fixed complete all as specified and directed by Eng-in-charge.

S&F in repair chromium plated shower rose with shower arm or without swivel joints including fixing to steel pipe of 100 mm size complete all as specified and directed by Eng-in-charge.

S&F in repair CP Jet spray butter fly design fixed on EWC with stanless screw as approve complete all as specified and directed by Eng-in-charge.

S&F in repair 450mm long PVC connection suitable for 15 mm bore with PTMT nuts on both sides complete all as specified and directed by Engineer-in-charge.

S&F in repairs PVC flexible waste down pipe-32 mm dia and 1150 mm long with PVC waste coupler complete all as specified and directed.

S&F in repair 15mm bore CP angle valve, fancy type, cast copper alloy, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed by Engineer-in-charge.

S&F in repair 2 way 15mm CP angle fancy type 15 mm bore high pressure screwed for iron pipe complete all as specified and directed by Eng-in-charge.

S&F in repair 15mm dia stop cock cast copper alloy, fancy type with, chromium plated long shank and cup (concealed type) with crutch or butterfly handle screwed down high pressure, screwed both ends for iron pipe complete all as specified & directed by Engineer-in-charge.

S & F in repair for 15mm bib tap standard of PTMT any colour screwed for iron pipe and fixed complete all as specified and directed by Eng-in-charge.

S & F in repair for 15mm angle cock standard of PTMT any colour screwed for iron pipe and fixed complete all as specified and directed by Eng-in-charge.

S & F in repair for 15mm Pillar tap fancy type standard of PTMT any colour screwed for iron pipe and fixed complete all as specified and directed by Eng-in-charge.

S&F in repair 15 mm bore bib tap, cast copper alloy, chromium plated, long body, fancy type screwed down and screwed for iron pipe or for brass ferrule complete all as specified and directed by Engineer-in-charge.

S&F in repair vitreous china squatting pan Orissa pattern, white of size 580x440mm with integral foot rests (excluding flushing cistern and flush pipe) including cast iron 'P' or 'S' trap, PCC filling and connection to trap and flushing pipe, antisyphonage pipe etc complete all as specified and directed by Engineer-in-charge.

S&F in repairs vitreous china wash down water closet pan (Pedestal pattern), white including connection to drain (or outgoing pipe) and to flushing pipe, anti-sypohonage pipe etc. & with plastic WC seat cover white closed pattern with flat bottom and cover and mild steel chromium plated or aluminized hinging device and jet spray complete all as specified & as directed by Engineer-in-charge.

S&F in repairs PVC EWC seat cover of any type, white colour for pedestal pan complete all as specified and directed by Eng-in-charge.

S&F in repair 10 litre capacity PVC valveless symphonic action type low level flushing cistern (ISI marked) including 32 mm dia PVC flush pipe connected to water closet with inlet, ball valve, float and handle complete all as specified and directed by Engineer-in-charge.

S&F in repairs, vitreous China wash hand basin, white, flat back size 550 x 400mm including 15mm dia, 450 mm long HDPE PVC connection, 750 mm long 32mm bore HDPE waste down pipe including CI brackets complete all as specified and directed.

S&F pillar taps (fancy type), of 15 mm dia, cast copper alloy, with capstan heads, with chromium plated, screwed down high pressure with or without lettered 'hot' or cold with long screwed shanks and fly nuts, screwed for iron pipe and fixed.

S&F in repair pillar taps (fancy type), of 15 mm dia, cast copper alloy, with capstan heads, with chromium plated, screwed down high pressure with or without lettered 'hot' or cold with long screwed shanks and fly nuts, screwed for iron pipe and fixed.

M&L preparation new or previously untreated steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over and including one coat of red oxide zinc chrome primer complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of steel surface already treated with primer over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge.

M&L preparation new or previously untreated steel surfaces of any description not exceeding 10 cm width or girth and applying two coats of synthetic enamel paint over and including one coat of red oxide zinc chrome primer complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of old steel surfaces of any description or girth over 10 cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed.

M&L for preparation of old painted wooden surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed.

S&F factory made steel window / ventilators conforming to IS-1038 with side hung shutters including projected type hinges with 2 Nos MS 100 mm size tower bolt over MS flat iron for each openable leaf & Z section handle and steel peg stay complete without glazing bars, dovetailed or welded including one shop coat of red oxide zinc chromate primer complete all as specified & directed by Engineer-in-Charge.

S&F factory made steel window conforming to IS-1038 with side hung shutters including projected type hinges with 2 Nos MS 100 mm size tower bolt over MS flat iron for each openable leaf & Z section handle and steel peg stay complete with glazing bars, dovetailed or welded including one shop coat of red oxide zinc chromate primer complete all as specified & directed by Engineer-in-Charge.

S&F factory made steel ventilator with top hung shutter including hinges, steel peg stay, handle including one shop coat of Zinc Chromate primer complete all as specified and directed by Engineer-in-charge.

S&F mild steel framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, cooler stand 12mm sq guard bar, framework of water tanks and similar works of quality Fe 290 (Gde E-165) etc complete all as specified and directed by Engineer-in-charge.

M&L for preparing newly plastered surfaces and applying applying two coats of distemper with distemper oil emulsion white or tinted over and including one coat of 1mm thick wall care putty complete all as specified and directed.

M&L for preparation of old distempered surfaces of walls and applying one coats of oil bound distemper white or tinted, complete all as specified and directed by Engr-in-Charge.

M&L for preparation of new plastered surface of wall and applying three coats of white wash complete all as specified and directed.

M&L for preparation of old decorated, plastered or pointed surfaces of wall by brooming down or steel wire brushing, scrapping down smoke soot moulds, moss and efflorescent, salts and treating oil & greasy spots etc and applying one coat of white wash complete all as specified & directed by Engineer-in-Charge.

M&L for preparation of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

M&L for preparation of old decorated, plastered or pointed surfaces of ceiling by brooming down or steel wire brushing, scrapping down smoke soot moulds, moss and efflorescent, salts and treating oil & greasy spots etc and applying one coat of white wash complete all as specified & directed by Engineer-in-Charge.

M&L for preparartion of new plastered surfaces of walls and applying two coats cement base paint on walls upto G+2 story bldg complete all as specified and directed.

M&L for preparation of old plaster surfaces of walls and applying one coat of cement based paint on walls for height upto G+2 story bldg complete all as specified and directed.

M&L for 25mm thick (measured solid) precast cement concrete (1:2:4) type B0 using 12.5mm graded stone aggregate) louvers and jallies, including all mouldings but excluding frame, set in CM (1:4) complete all as specified and directed by Engineer-in-Charge.

M&L for rendering dubbing coat over irregular surfaces of chajjas roof projections / ceiling / facia etc average 15mm thick in CM (1:4) over cement slurry coat @ 3Kg/Sqm making the surface even followed by 5mm thick rendering in CM (1:3) furnished even & smooth including making of drip course as required complete including roughening surface of old concrete by picking sweeping clean and washing with water complete all as specified and directed. Note : Rate for form work if required to be included in the quoted rate by the contrator.

S&F in repairs curtain rod, stainless steel of 25mm dia with fixing brackets stop rollers etc fix complete all as specified and directed.

S&F in repair CP Health faucet with stand fixed on wall in CP hose pipe 1 mtr length and stainless steel screw as approve complete all as specified and directed by Eng-in-charge.

S&F in repair brass chromium plated tubular towel rail 20mm dia; 'D' type, 600mm long between flanges fixed to plug with chromium plated brass screws including wooden or plastic cleat complete all as specified and directed by Engineer-in-Charge.

S&F in repair PVC Syphon kit assembly in existing flush tank complete all as specified and directed.

S&F in repair PVC mirror cabinet size 350X450mm of standard size fixed to wall with PVC sleeves and steel screws complete all as specified and directed.

S&F in repairs Sheet glass shelf assembly consisting of 5.5mm thick sheeet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

S&F in replacement 18mm thick PVC Celuka Ply plain white colour both side fixed with screws solvent cement/adhesive to make kitchen cabinet sides top and bottom and shelves inside the cabinets complete as per specifications and as directed by the Engineer-in-Charge (Density - 575 to 600 Kg/CBM)

S&F in replacement 18 MM thick PVC Celuka board of single side prelam/rigidlam color fixed with screws, solvent cement/adhesive to make kitchen cabinet sides top and bottom and shelves inside the cabinet, cupboard shutters/frames, (Density- 575 to 600 Kg/ CBM), complete, all as directed by Engineer-in-Charge.

S&F auto closing hinges 35mm of 0 crank (KH-001) or 8 crank (KH-002) openable at 110 degree for kitchen cabinet shutters complete all as specified and directed.

S&F Continuous (piano) hinges 40 mm, mild steel, bright finish or electrogalvanised complete all as specified and directed.

S&F 100mm long stainless steel handles, oval type complete all as specified and directed.

S&F ball bearing runners 45mm telescopic (KTS-20) full extension load capacity 50 Kgs complete all as specified and directed.

S&F Magnetic catcher fixed in with nut,screw washer complete all as specified and directed by Eng-in Charge.

S&F in repair CI nahani trap 100mm dia outlet plain with grating including jointing with solvent cement including jointing to waste pipe fixed in cement concrete 1:2:4, type B-1 complete all as specified and directed.

S&F in repairs CI floor trap 100mm dia outlet plain with grating including jointing with solvent cement including jointing to waste pipe fixed in cement concrete 1:2:4, type B-1 complete all as specified and directed.

S&F in repair stainless steel grating 100mm bore size fixed with white cement complete all as specified and directed by Eng-in-charge.

S&F in repairs CP Soap dish, embedded in the wall approximate size 160x160x90mm complete all as specified and directed.

S&F in repair stainless steel kitchen sink 1 mm thick kitchen / laboratories with plug washer and waste including bedding in cement mortar and fixing cantilever brackets and connecting union to pipe overall size 495 mm x 420 mm bowl size 410 mm x 330 mm x 160 mm complete all as specified and directed.

S&F in repair of HDPE PVC lid tank cover for any capacity all as specified and directed.

S&F hollow corrugated shape PVC wall lining consisting of 5mm thick decorative colour PVC sheet inclusive of solvent cement and fixing and incl beading at sides on PVC frame as per specifications all as specifed complete all as specified and directed.

S&F in repair stainless steel plate rack of size 900mm x 900mm x 254mm made out of 0.80mm thick stainless steel of first quality complete all as specified and directed by Engineer-in-Charge. Make :- Nirali model Elegance (Glossy) / Prayag Gold Series (Gloss) / Silver Shine (Bluestar sanitary industries Pvt Ltd).

Taking down surface / concealed copper / aluminium point wiring (light, bell, fan, socket or power) complete, including fixtures and fittings such as switches, ceiling roses, lamp holders, pendants, sockets, regulators, tubelight fittings etc and making good disturbed surfaces with plaster on walls, floors etc complete all as specified and directed.

M&L for Point wiring complete with 1.5 sqmm single core FRLSH PVC insulated cable with multi stranded copper condutor in and including PVC conduit 20mm dia and thickness not less than 1.5mm, ISI marked with all accessories for surface or concealed conduit as directed at site incl chase cutting for one light/fan point controlled by one one way switch including MS sheet sunken box concealed on wall duly painted inside and outside with one coat of red oxide primer and two coats of black bituminous paint with 3mm thick hylum brand bakelite sheet cover for fixing switches, sockets, regulators etc. alongwith 1.5 sqmm multi stranded FRLSH, PVC insulaedcopper cable as continuous earth connected to common earth and earth dolly including making good the disturbed surfaces complete all as specified and as directed.

All as per Sl item No 125.00 above here-in-before for light point controlled by two way switch complete all as specified and directed.

All as per Sl item No 125.00 above herein before but for one bell point controlled by one bell push.

All as per serial item No. 125.00 here-in-before but for One 3 pin 5 Amp socket outlet on independent board.

All as per serial item No. 125.00 here-in-before but for One 5 pin 5 Amp socket outlet on the same board with other switches.

All as per item No 125.00 (here-in-before) but for one 6 pin socket outlet 16amps point controlled by one switch on independent board.

M&L for Sub main wiring with 2 runs of 4 sqmm single core PVC insulated but unsheathed multistranded copper conductor FRLSH 1100 volts grade cable drawn through and in existing surface / recessed PVC conduit and connecting incoming/outgoing electric connections and one run of 4 Sqmm single core PVC insulated but unsheathed multistranded copper conductor FRLSH 1100 volts grade cable as earth conductor including taking down old unserviceable submain wiring and making good disturbed surfaces complete all as specified and directed. Note : Two runs of 4 Sqmm cable, one run of 4 Sqmm earth conductor and one run of PVC conduit of 25mm dia shall be measured and paid as one unit length.

M&L for Sub main wiring with 2 runs of 6 sqmm single core PVC insulated but unsheathed multistranded copper conductor FRLS 1100 volts grade cable drawn through and in existing surface / recessed PVC conduit and connecting incoming/outgoing electric connections and one run of 6 Sqmm single core PVC insulated but unsheathed multistranded copper conductor FRLS 1100 volts grade cable as earth conductor including taking down old unserviceable submain wiring and making good the disturbed surfaces complete all as specified and directed. Note: Two runs of 6 Sqmm cable, one run of 6 Sqmm earth conductor and one run of PVC conduit of 32mm dia shall be measured and paid as one unit length.

M&L for Sub main wiring with 2 runs of 10 sqmm single core PVC insulated but unsheathed multistranded copper conductor FRLS 1100 volts grade cable drawn through and in existing surface / recessed PVC conduit and connecting incoming/outgoing electric connections and one run of 10 Sqmm single core PVC insulated but unsheathed multistranded copper conductor FRLS 1100 volts grade cable as earth conductor including taking down old unserviceable submain wiring and making good the disturbed surfaces complete all as specified and directed. Note: Two runs of 10 Sqmm cable, one run of 10 Sqmm earth conductor and one run of PVC conduit of 32mm dia shall be measured and paid as one unit length.

Supply and laying in replacement of Non Metallic Rigid PVC conduit, ISI Marked, conforming to IS 9537, medium grade, size 25 mm dia including all fittings like bends, elbow reducer, junction, coupler boxes, tee bell mouth etc for protection of cables/wires complete in all respect as specified and directed.

Supply and laying in replacement of Non Metallic Rigid PVC conduit, ISI Marked, conforming to IS 9537, medium grade, size 20 mm dia including all fittings like bends, elbow reducer, junction, coupler boxes, tee bell mouth etc for protection of cables/wires complete in all respect as specified and directed.

Supply and laying in replacement of worn out PVC rigid conduit with uPVC trunking/casing caping of size 50mm x 16mm including fittings conforming to IS 14927/2001, fixed to wall/ceiling surface to cover the cable/wire complete all respect as specified and directed.

M&L for cutting chases, pining in making good to facing where required and pointed in CM (1:3) to ends or edges of brick wall etc and cutting chases for concealed conduit wiring etc and making good, match with existing surfaces by applying white/colour wash cutting not exc 10cm girth complete all as specified and directed.

S&F switch piano flush button single pole, one way 5 Amp 240 Volt complete all as specified and directed.

S&F switch piano flush button single pole, one way 15 Amp 240 Volt complete all as specified and directed.

S&F switch piano flush button single pole, two way 5 Amp 240 Volt complete all as specified and directed.

S & F Switch Bell push 5 amp single Pole 230 V all as specified & directed.

S&F socket outlet 6 amps 5 pin flush type, 230 volts complete all as specified and directed.

S&F socket out let, 6 pin 5 and 15 amps multi purpose 2 in 1 flush type 230 volt complete all as specified and directed.

S&F in repair sheet metal enclosure Single pole & neutral with 2 pin and earth plug and socket 20A 240 Volt complete with one single pole MCB of cap 20/25 A, C series complete all as specified and directed.

S&F ceiling rose 63x30 mm three terminal, polycorbonate body complete all as specified and directed.

S&F fan regulator electronic, five step type hum free suitable control speed of fan from 0 to 100% and connecting electrically all as required complete all as specified and directed.

S&F Angle / batten holder polycorbonate type body suitable for batten fitting complete all as specified and directed.

S&F in repair adaptor, 240 volts polycorbonate type body for proper connection to LED batten through batten holder complete all as specified and directed.

S&F in replacement musical door bell (having locking features) including 2 Nos, AA 1.5 volt battery for working even when no electricity suitable for 230 volts AC supply complete all as specified and directed.

S&F in replacement sketch fitting with decorative, wall mounting, brushed nickel finish fixture with acrylick diffuser including fixing 12 watt rechargable/invertor LED lamp, B22 base cap complete all as specified and directed.

S&F in replacement of LED security / street light, 45 Watt, IP - 66, Impact resistance - IK07, colour temp- 5700 K, Class I in Pressure die-cast aluminium alloy for housing (heat sink) for effective thermal management, sturdiness, excellent corrosion resistant, separate optical and control gear compartment & top opening for easy maintenance. Polyster powder coated grey after phosphochromate treatmentHigh efficiency long life LED modules with SMD LED package mounted on MCPCB. Lumen efficacy of LED >110 lm/W with PC lens to ensure better uniformity of light distribution. Powered by Built-in, Potted electronic LED driver (SMPS based constant current supply) with lower THD, Output Open Circuit protection, Phase to Phase protection, Over Voltage protection, Surge Voltage protection upto 10 kV with external SPD & other safety tests as per IS 15885 Part-2/ Sec13. Suitable for bldg/pole mounting alongwith single arm bracket OD 58 mm (max) with suitable reinforcement on wall height complete in all respect & as directed.

S&F in repairs MCCB, 100 Amp, 4 Pole, 36 KA, 415 volts adjustable thermal & fixed magnetic setting complete all as specified and as directed.

S&F in repairs MCCB, 63 Amp, 4 Pole, 36 KA, 415 volts adjustable thermal & fixed magnetic setting complete all as specified and as directed.

S&F in repairs TPN MCB, 415 volts, 10 KA, 4 Pole, 100 Amps C series complete all as specified and as directed.

S&F in repairs TPN MCB, 415 volts, 10 KA, 4 Pole, 63 Amps C series complete all as specified and as directed.

Supply & fixing in replacement of MCB DP, 240 Volt, 10 KA, 40 Amps, C series complete all as specified and directed.

Supply & fixing in replacement of MCB DP, 240 Volt, 10 KA, 63 Amps, C series complete all as specified and directed.

Supply & fixing in repair LED constant driver suitable for 2' x 2' LED luminaries of wattage from 30 to 40 watt, 25 to 42 volts DC including fault detection, soldering and testing complete all as specified and directed.

Supply & fixing in repair LED constant driver suitable for LED batten 18/20 watt, input voltage range - 110 to 280 volts AC, output voltage range 40 to 75 volts DC including fault detection, soldering and testing complete all as specified and directed.

S&F in replacement surface and wall mounted 20 watt LED batten, PVC housing provided for efficient heat dissipation with polycarbonate diffuser & integrated electronic driver complete all as specified and directed.

S&F in replacement 10W integrated LED bulk head luminaire environment friendly, ultra modern, energy saving, surface mounted decorative oval bulk head with LED light, complete all as specified and directed.

S&F in replacement surface and wall mounted 10 watt LED batten, PVC housing provided for efficient heat dissipation with polycarbonate diffuser & integrated electronic driver complete all as specified and directed.

Supply & fixing in replacement ceiling light with 36W Watt, 6000 K, slim LED panel 2' x 2' LED panel for recessed on ceiling) dust-free installation with high brightness LEDs for glare-free homogenous illumination with driver and all other connected accessories complete all as specified and directed.

Supply & fixing in replacement sheet metal enclosure MCB distribution board triple pole & neutral 415 volts 4 way with IP-43 IK-09 protection double door complete with appropriate size bus bar and neutral link, fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and directed.

Supply & fixing in replacement sheet metal enclosure MCB distribution board single pole & neutral 240 volts 12 way with IP-43 IK-09 protection double door complete with appropriate size bus bar and neutral link, fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and directed.

Supply & fixing in replacement sheet metal enclosure MCB distribution board single pole & neutral 240 volts 8 way with IP-43 IK-09 protection double door complete with appropriate size bus bar and neutral link, fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and directed.

Supply & fixing in replacement of MCB single pole 240 volt any rating from 6 to 32 amps, B series with rupturing capacity 10 KA complete all as specified and directed.

S & F modular type 6A one way SP switch 1 module confirming to IS: 3854-1997 with finger proof terminal complete all as specified and directed.

S & F modular type 2/3 pin 6 Amps socket 2 module conforming to IS: 1293-2005 complete all as specified and directed.

S & F modular type 16 A one way SP switch 1 module confirming to IS: 3854-1997 with fingure proof terminal complete all as specified and directed.

S & F modular type 2/3 pin 16 Amps socket 2 module conforming to IS: 1293-2005 complete all as specified and directed.

S&F modular type 3/5 pin socket with one single pole MCB 20 Amp 230 Volts concealed in wall complete all as specified and directed.

S & F modular type 120W step fan regulator of 2 module size conformng to IS: 11037-1984 complete all as specified and directed.

S & F in repair shock safe plug 16A 30 Ma PRCD plug top, 220 V, equipped with an auto trip feature which shuts off detects any current leakage, fuse must be used as a back up protection for over load 6IEC:61540 recommeded complete all as specified and directed.

Supply and fixing in replacement ceiling fan (5 star rated by Bureau of energy with service value of not less than 6.12) BLDC, (40W±10%) aerodynamically design blades made of compounded ABS to give air friction for silent operation, with air delivery 240 Cum/min, rated speed 280 Rev/min, with or without remote complete with blades, down rods, electronic regulator and accessories, 230 volt, 1200 mm sweep, suitable for single phase supply with noise level 56 db, low voltage, starting input voltage 140 V (Max) with power factor 0.95 complete all as specified and directed. Note : Old unserviceable ceiling fan shall be deposited in AGE E/M store yard.

Supply and fixing in replacement exhaust fans 300 mm sweep metallic body, heavy duty, four blade, double ball bearing, 1400 RPM, minimum air delivery discharge 1710 CMH suitable for SP, 230/250V, 50 Hz AC supply with protective bird guard with louver shutters including grouting of frame in wall and connecting with and including 3 run 1.5 Sq mm single core, PVC insulated but unsheathered FRLSH multistranded copper conductors cable from ceiling rose to exhaust fan complete all as specified and directed. Note : Old unserviceable exhaust fan shall be deposited in AGE E/M store yard.

S&F in replacement Exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230 V, 5 Hz, RPM 1200, copper winding of sweep 300mm complete all as specified and directed. Note : Old unserviceable exhaust fan shall be deposited in AGE E/M store yard.

M/S CHAUDHARY CONSTRUCTION (BID ID -3403943)

Ms Kamal Kant Agarwal (BID ID -3404066)

MAHTAB ALAM (BID ID -3403742)