GE/ALP (8462) KOLKATA OF 2025-26

Amount

Dismantling removing all unsound concrete, plastered material by chipping / chiseling gently at all effected and adjoining areas of concrete etc till sound surface is reached all various locations in building subsequently cleaning the surfaces by hair brush and air blower and removing rubbish off the premises and disposing at the dumping site as approved by local authorities including hoisting assembling and fixing of double layer steel scaffolding to external perimeter of building complete all as specified and directed. (upto 4 storied bldg)

All as per item No-01 here in before but for 5 to 8 storied bldg.

Removing of concrete all around reinforcement bar upto 12 mm dia and over from behind the reinforcing bars average 25mm (but not less than 15 mm air gap) by manual methods (using wire brushing, chiseling etc) and applying chloride free rust removing chemical on rusting steel reinforcement bar and removing all rust from steel reinforcement bar by emery paper and cleaning the area thoroughly by water and allow it to dry and totally rust free of reinforcement bar all as complete as per manufacturer's instruction as specified and directed. (upto 4 storied) Make(Rust removing chemical) :- Reebaklens RR of FOSROC or equivalents solutions SIKA/STP.

All as per item No-03 here in before but for 5 to 8 storied bldg.

M&L for preparation of existing reinforcement surface by brush and application of two component epoxy zincrich primer on existing reinforcement surface of minimum specific gravity 1.75, adhesive bond strength with steel is 1.50N/mm2 and maximum coverage area 5.00 Sqm per litrecomplete all as specified and directed. (upto 4 storied bldg). Make- Nitozinc primer of FOSROC or equivalent make as approved by GE.

All as per item No 05 here in before but for 5 to 8 storied bldg.

M&L for introducing new reinforcement bars upto 12 mm dia and over for structural connection in RCC beams, columns, lintel and slabs including power drilling holes of appropriate diameters in reinforced or plain cement concrete to a minimum depth of 150 mm and upto 200 mm including power drilling, fixing the reinforcement in position using epoxy, cleaning of loose dust by blowing air, sealing with epoxy cartridges etc complete all as specified and directed. (upto 4 storied bldg)

All as per item No 07 here in before but for 5 to 8 storied bldg.

M&L for supply, mixing and placement of micro-concrete cement based prepacked single component chloride free, sulphate free, non-shrink, free flow. elf compacting, ready to use after mixing water in specified proportion of Sika Rep Microconcrete-4 or renderoc-RG of Fosroc in required thickness as per manufacture's instruction and all as directed. Compressive strength (ASTN C 109,cm cube) of 35 MPa at 28 days including application curing compound concrete WB manufactured by Fosroc of equivalent at various locations in Bldgs including necessary form work complete all as per manufactures specification. (upto 4 storied bldg)

All as per item No 09 here in before but for 5 to 8 storied bldg.

M&L for providing and applying at two component structural grade polymer modified reinforcement mortar Fosroc Renderoc S2 or equivalent product of SIKA upto a thickness of 30 mm over a coat of epoxy resin bonding agent Nitobond EP. The cured mortar shall achieve a minimum compressive strength of 12N/mm2 in a day & 45 N/mm2 in 28 days with Flexural strength 8N/mm2 in 28 days Chloride diffusion coefficient shall be Nil after 24 hours when tested by Accelerated electrochemical chloride ion diffusion test method and the depth of carbonation shall be Nil after 24 hours when tested by Accelerated carbonation test. in addition to this percentage of water absorption should be 0.45 after 24 hours in immersion test at various locations in Bldgs complete all as per manufacture's specification. (upto 4 storied bldg)

All as per item No 11 here in before but for 5 to 8 storied bldg.

M&L for applying of high efficiency polymeric resin base film forming curing agent/compound over concrete surface and maximum coverage area 5.00 Sqm per litre as per manufacturers instruction complete all as specified and directed. Make:- Concure LP90 of FOSROC or equivalents solutions SIKA/STP/ Maruti / Choksey chemicals. (upto 4 storied bldg)

All as per item No 13 here in before but for 5 to 8 storied bldg.

M&L for providing and applying a flexible expansion joint membrane of minimum 150mm wide and 1mm thick, expoband one of FOSROC or equivalent over the prepared joint using a two part epoxy adhesive nitobond PC 40 of Fosroc or equivalent. The minimum tensile strength of the membrane should be more than 12 N/mm2 and elongation at break should be more than 400%. The installation of the membrane should be carried out as per manufactures specification. (upto 4 storied)

All as per item No 15 here in before but for 5 to 8 storied bldg.

M&L for providing and inserting mild steel shear key bars/levelling gauges of required length and diameter in reinforced/plain concrete for drilling suitable holes in RCC slab/ wall/ column/ beams toa depth as directed for anchoring steel reinforcement bars including washing with water inserting lokfix 'E' of Fosroc or equivalent in the holes at various location in Bldgs complete all as per manufactures specification. (upto 4 storied bldg)

All as per item No 17 here in before but for 5 to 8 storied bldg.

M&L for applying Anti carbonation coating as per manufacturer's specification of approved brand, manually using brushes on the hardened concrete /plastered surfaces after cleaning the surface and removing all loose particles, deposits etc complete including one coat of primer and two coats coatings as directed.(upto 4 storied bldg)

All as per item No 19 here in before but for 5 to 8 storied bldg.

M&L for providing grouting in RCC walls and slabs by drilling holes @300 mm c/c upto half of the wall depth in zigzag manner using a drill machine and fixing a nozzle of 20mm dia, for injecting of epoxy grout till the refusal of injected grout material (grouting operation pressure shall be in between 2 to 4Kg per sq cm) followed by cutting the exposed nozzle so as to make the wall/ slab free from the grouting pipe and to seal the gap with polymer modified mortar complete all as specified and directed. Make- Fosroc conbextra Ep10(M) or equivalent make as approved by GE. (upto 4 storied bldg)

All as per item No 21 here in before but for 5 to 8 storied bldg.

Hacking out old broken glass any thickness, size quality or description from wooden/steel frame fixed with wooden beads/metal pinning complete all as specified and directed

S&F for 4 mm thick Figured glass in square not exc. 0.50 sqm in each pane, fixed with pin headed beads or putty (in metal frames etc) complete all as specified and directed.

S&F for 5.5 mm thick plain sheet glass and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and directed.

S&F in repair stainless steel wire cloth with stainless steel 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with wire staples (for windows and gauzed doors) all as specified and directed.

S&F in repairs aluminium anodized extruded bow handle fabricated type 125 mm long complete all as specified and directed.

S&F in repairs 100 mm long mild steel butt hinges, medium weight, cold rolled and fixed complete all as specified and directed.

S&F in repairs 200mm long aluminium, anodised, barrel tower bolts of extruded section and fixedcomplete all as specified and directed.

S&F in repair stainless steel curtain rod anodised aluminium alloy 25 mm dia with pair of suitable brackets,finnels and also making good the wall surface to match the existing surfaces complete all as specified and directed.

S&F in repair 300 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc.) any thickness, including cover fillets complete all as specified and directed.

M&L for suspended false ceiling (Decorative Type) system using metalic (E grid) exposed suspende system, grid section size 600 mm x 600 mm comprising of GI powder coated main runner of dimension 32 mm x 24 mm x 0.80 mm thick ( thickness comprising of GI/0.4+ PPPCGS/0.3 mm & weight of Runner) Cross Tee of dimensions 26 mm x 24 mm x 0.8 mm thick, wall angle 22.00 mm x 22.00 mm x 0.35 mm thick ( thickness comprising of GI/0.35 + PPPCGS/0.3 mm) with and including 4 mm thick HPSC ( High pressure steam cured) pre- primed, self embossed textured designer board, water resistant termite resistant, fire resistant for insulation and accustic purpose to be placed in the grid system duly suspended with 4 mm dia G I bars hangers fixed with steel dash through fasteners with Provn of light fixture complete all as specified and directed.

M & L for GI frame work for seamless ceiling comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/ intermediate channel 0.9mm thick having two equal flanges of 15mm each and web of 45 mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc. 1.2m length) of 0.55 mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to intermediate channel with connecting clips across the intermediate channel at 457mm centre to centre and incl Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat (40 x 3) mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified.

S&F for Gypsum Board 12mm thick in ceiling flat or slopping fixed in jointless finish with jointing compound and jointing tape fixed with screw as per manufacturers instructions with provn of light/electric fixtures complete all as directed complete all as specified and directed.

M&L for preparing new gypsum board ceiling, pillasters, cornices etc and applying one coat of 3 mm thick wall care putty with two coat acrylic distemper complete all as specified and as directed.

S&F in repairs vitreous China wash down water closet pan (pedestal pattern) incl PVC seat cover, (excluding fixing bolts, flushing cistern and flush pipe), including connection to drain ( or outgoing pipe) and to flushing pipe etc. complete complete all as specified and directed.

S&F in repair PVC valveless, symphonic action type low level flushing cistern white with inlet ball valve, float and handle including brackets, 10 ltr capacity complete with flush pipe(Long bend) 32 mm dia and complete all as specified and directed.

S&F in repairs white Plastic water closet seat cover, closed pattern with flat bottom, and mild steel chromium plated or aluminised hinging device complete all as specified and directed.

S&F in repair CP tubular towel rail 600mm long 20 mm dai complete all as specified and directed.

S&F in reapir 25 mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F in repair 110/125 mm floor trap fixed in floor with grating incl jointing with solvent (1:2:4) cement concrete, complete all as specified and directed.

S&F in repair Vitreous china squatting pan of orissa patern size (580 mm x 440 mm) white with integral foot rest (excluding flushing cistern and flush pipe) complete all as specified and directed.

S&F in repair Urinal spreader of CP any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms) complete all as specified and directed.

S&F for half stall Vitreous China urinals, bowl type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar (1:2), securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) complete all as specified and directed.

S&F in repairs 15 mm Dia CP Bib taps (Two-in-one), fancy type with crutch handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F in repairs Health Faucet mild steel chromium plated suitable for 15 mm dia pipe with 1.25 mtr long flexible tube and wall hook including making connections and fixed in position complete all as specified and directed.

supply only white cement in bags of 25 Kgs packing complete all as specified and directed.

S&F in repair 15 mm dia bib tap cast copper alloy chromium plated with capstan head handle, screwed down high pressure screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repairs 15mm dia fancy type Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed.

S&F in repairs 15 mm dia stop valve cast copper alloy chromium plated with capstan head handle, screwed down high pressure screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repairs 15mm dia angle valve, chromium plated, screwed down high pressure, with crutch or butterfly handle screwed both ends for iron pipe on for unions, complete all as specified and directed.

S&F in repairs Brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed complete all as specified and directed.

S&F PVC (SWR) gully trap 125/110 mm,setting and jointing with solvent cement complete all as specified and directed.

S&F in repairs Brass CP mixer for mixing hot & cold water (for wash hand basin) and fixed including dismantling of 15mm dia chromium plated pillar tap, complete all as specified and directed.

S&F in repairs 15 mm dia wall mixer cost copper alloy chromium plated with capstan head handle, screwed down high pressure screwed for iron pipe or for brass ferrule complete all as specified.

S&F in repairs 110 mm bore PVC (SWR) Pipes single socket, complete all as specified and directed.

All as per item No 58 here in before but 75mm bore

S&F in repairs PVC bend/tee suitable for 110mm bore pipe complete all as specified and directed.

All as per item No 60 here in before but 75mm bore

S&F in repairs door closer hydraulically regulated (extruded section) , designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 complete all as specified and directed.

S&F in repairs door closer hydraulically regulated (extruded section) , designation No. 2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 61 to 80 complete all as specified and directed.

S&F in repairs heavy duty double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box,main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel complete all as specified and directed.

S&F in repairs 19 mm thick prelaminated particle board, interior grade, prelaminated both side with decorative choice lamination & other side balancing white lamination, fixed with screw to timber frame work complete all as specified and directed.

Dismantling of floor, hearth or wall tiling including cement mortor bedding (but not backing removing serviceable to store and rubbish off the premises complete all as specified and directed.

M&L for glazed ceramic (coloured) tiles of size 450 mm x300 mm x 6-7mm thick as in vertical surface /dado set and jointed in adesive and pointed in white or coloured cement to match complete all as specified and directed.

M&L for Anti-skid joint free ceramic (coloured) tiles 7-8mm thick area of each tiles exeeding 0.06sqm but n.exceeding 0.11 sqm in toilet/bath floor etc.set and jointed with adesive and pointed in epoxy grout with spacers complete all as specified and directed.

M&L for Non Skid joint free ceramic tiles 7 to 8 mm thick(square/ rectagular) area of each tile exceeding 0.18 sq m but not exceeding 0.38 sqm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match incl 15mm thick screed bed or bedding layer in cement mortar (1:6), complete all as specified and directed.

Dismantling of stone slabs and tiles of any description or thickness in floors,aprons etc laid, bedded & pointed in any mortar complete all as specified and directed.

M&L for Granite (of any type) tiles 20 mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified and directed.

M&L for 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, indow-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

M&L for screed bed or bedding layer of mortar 20 mm thick in cement mortar (1:6) for laying floor finishes complete all as specified and directed.

M&L for screed bed or bedding layer of mortar 15 mm thick in cement mortar (1:6) for laying floor finishes complete all as specified and directed.

M&L for bedding layer of mortar 10 mm thick in cement mortar (1:3) for laying wall/dado finishes complete all as specified and directed.

M&L in repair rotational moulded polythylene water storage tanks 500 litres capacity (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified including 20 mm brass valve high pressure with polythene float and fly nut complete and GI tank nipple, screwd for iron pipe complete all as specified and directed.

All as per iten No 76 here in before but 1000 ltr capacity.

All as per iten No 76 here in before but 2000 ltr capacity.

Taking down wooden/steel chowkhats/door/window frame including shutter (without taking off shutter) exc.1.5 Sqm but n exc 4 sq m each and removing to or from store complete all as specified and directed.

Taking down wooden/steel chowkhats/doo/window frame including shutter (without taking off shutter) not exc.1.5 Sqm each and removing to or from store complete all as specified and directed.

S & F factory made 2nd H/W plain solid straight chowkhats,wrought framed rebated on the solid,rounded or chamfered put together with glue pinned at joints complete all as specified and directed.

M&L for Factory made 30 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides with both face covered with decorative face veneer with lipping/frame to match complete all as specified and directed.

S&F for Factory made, 2nd class Hard wood of thickness 35 mm, Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. divided into squares, with plain, chamfered or rounded, mitred and rebated with sash bars, any numbers, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc. sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a) supplied and fitted to chowkats complete all as specified and directed.

S&F for Factory made single extruded WPC (Wood polymer composite) solid door Frames of size 45 mm x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension grade), calcium carbonate & natural fibres and non-toxic additives fabricated with mitre joints after applying PVC solvent cement and screwd with full body threaded star headed SS screws having minimum frame density of 750 Kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), mimimum compressive strength of 58 N/Sqmm and resistance to spread of flame of class A category with property of being termite/borer proof, water/moisture proof & fire retardant & fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete all as specified and directed.

S&F for Factory made single extruded WPC(Wood polymer composite) solid flush door shutter of 30 mm size comprising of virgin PVC polymer of K value 58-60 (Suspension grade), calcium carbonate & natural fibres and non-toxic additives fabricated with mitre joints after applying PVC solvent cement and screwd with full body threaded star headed SS screws having minimum density of 650 Kg/cum, screw withdrawal strength of 1800 N(Face) & 900 N (Edge), mimimum compressive strength of 50 N/Sqmm, modulas of elasticity 850 N/sqmm & resistance to spread of flame of class A category with property of termite/borer proof, water/moisture proof & fire retardant & fixing with SS butt hinges of required size with necessary full body threaded star headed counter sunk SS screws, complete all as specified and directed.

S&F for powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium ections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/paneling, C.P. brass/ stainless steel screws complete all as specified and directed.

S&F Anodised powder coated aluminium (minimum thickness of powder coating 50 micron) frame for doors, windows, ventilators or aluminium frame for partition works etc with one or more rebates including joining cleat for fixing etc. complete all as specified and directed

S&F for Anodised powder coated aluminum Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specifiedr and including dismantling of existing unserviceable Aluminium window complete all as specified and directed.

S&F for anodised aluminium grill (anodised transparent or dyed to required shade according to IS:1868) of approved design/pattern, with approved standerd section and fix to the existing window frame with C.P brass / stainless steel screws @ 200mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, complete all as specified and directed. (only weight of grill to be measured for payment)

S&F for 12 mm thick prelaminated particle boards (ISI marked), interior grade prelaminated both side with decorative choice lamination, fixed with necessary clips and other like to aluminium frame work, as in doors, windows, partition etc complete all as specified and directed.

M&L for Cub-boards shutters made with Prelaminated Particle board 18/19 mm thckness , interior grade prelaminated both side with decorative choice lamination, fixed with screws to timber frame work complete all as specified and directed.

S&F for Glass film reflective type sticked to glass panes as per instructions of manufacturers intructions complete all as specified and directed.

M&L for easing aluminum door shutter of any description incl taking down shutter and refixing in the same opening after rectifying all defects in the shutter, oiling / servicing of floor spring, hydraulic door closer, tightening all loose screws, cleats, etc replacing all rubber gaskets / aluminium beading complete all as specified and directed. Note: The minor parts such as screws, cleats, oil, rubber neoprene gasket, aluminium beading etc shall deemed to be including in quoted rate.

S&F for mild steel framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars, barred iron doors, angle iron chowkhats, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed. .

Taking down wooden/steel chowkhats/door frame including shutter (without taking off shutter) exc.4 Sqm each complete all as specified and directed.

S&F for 1.25 mm thick lath Steel rolling shutters, with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer and two coat of synthetic enamel paint ;erected in position as indicated, complete:but gear operated type with bevel gear box and crank handle complete all as specified and directed.

S&F in repairs safety lever locks mild steel with 4 levers for rolling shutters complete all as specified and directed.

S&F in repairs Ball bearing including suitable springs for rolling shutters complete all as specified and directed.

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar (1:3) to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing etc., and making good, cutting not exc 10 cm girth complete all as specified and directed.

Taking up or down 15mm bore steel water tubing and connections,including cleaning for removal to store (GI Pipe) complete all as specified and as directed.

Taking up or down 20mm bore steel water tubing and connections,including cleaning for removal to store(GI Pipe) complete all as specified and directed.

Taking up or down 25mm bore steel water tubing and connections,including cleaning for removal to store(GI Pipe) complete all as specified and directed.

S&F for CPVC pipes 16 mm outer diameter of SDR 11 & plain CPVC SDR 11 fittings as in walls, ceiling, floor, etc. complete all as specified and directed.

S&L for 20 mm bore (Outer dia) CPVC pipes of SDR 11and plain CPVC SDR 11 fitting fixed on wall or floor (concealed ), ceiling or laying in floors complete all as specified and directed.

S&L in 25 mm bore (Outer dia) CPVC pipes of SDR 13.5 and plain CPVC SDR 11 fitting fixed on wall or floor, ceiling or laying in floors complete all as specified and directed.

S&F for 20 mm bore CPVC Male Brass Threaded Adaptor (MTA/ MBTA) complete all as specified and directed.

S&F for 25 mm bore CPVC Male Brass Threaded Adaptor (MTA/ MBTA) complete all as specified and directed.

S&F for 20 mm bore CPVC Female Brass Threaded Adaptor (FTA/ FBTA) complete all as specified and directed.

S&F for 25 mm bore CPVC Female Brass Threaded Adaptor (FTA/ FBTA) complete all as specified and directed.

S&F in repairs PVC connections 15mm size with PTMT nuts of length 600mm complete all as specified and directed.

S&F in repairs 32 mm PVC waste pipe 900 mm long with complete all as specified and directed.

S&F for sinks with drainage board made of stainless steell 1 mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915 mm x 460 mm bowl size 410 mm x 330 mm x160 mm complete all as specified and directed.

S&F for sinks made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495 mm x 420 mm bowl size 410 mm x 330 mm x 160 mm complete all as specified and directed.

S&F for Vitreous China wash basin, angle back, size 600 mm x 480 mm white, excluding taps, waste, chain and plug and porcelain stopper but including brackets complete all as specified and directed.

Demolition of brickwork or stone boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc. but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

M&L for brick work with flyash old size bricks, straight or curved on plan exc 6m mean radius, built in cement mortar (1:6) complete all as specified and directed.

M&L for brick work with flyash old size bricks, straight or curved on plan to any radius in half brick thick walling built in cement mortar (1:4) complete all as specified and directed.

Taking down cement plaster on brick or stone wall surfaces including glazed tiles wherever exists including raking out joints, hacking for key and scrubbing down with water complete all as specified and directed.

M&L for 5mm thick plastering on ceiling surfaces in CM (1:3) surface finished even and fair complete all as specified and directed.

M&L for 20mm thick (in two layer) plastering on fair face of Brick surface with cement mortar (1:4) mixed with WPC finish surface even and smooth with out using extra cement complete all as specified and directed.

M&L for 15mm thick cement plaster with cement mortar (1:6) on other than fare face of brick wall finsh even and smooth without using extra cement complete all as specified and directed.

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, tranporting, unloading to approved municipal dumping ground outside MoD land where directed complete all as specified and directed.

Complete removal of existing treatment by using electric sander machine or steel wire brushing to remove all dust and loose scale etc of wall surfaces & prepare to receive wall care putty complete all as specified and directed.

M&L for 1mm thick wall care putty on wall including rubbing with sand paper to achieve a smooth surface & sharp straight edges etc. complete all as specified and directed.

M&L for preparation old decorated walls & applying two coats of acrylic oil emulsion distemper complete all as specified and directed.

M&L for preparation of decorated Ceiling & applying two coats of acrylic oil emulsion distemper complete all as specified and directed.

M&L for preparation of newly plastered wall surface two coats of oil bound distemper over a coat of primer on complete all as specified and directed.

M&L for applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over 2mm thick wall care putty and icluding priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed.

M&L for Complete removal of existing treatment and applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over old surfaces complete all as specified and directed.

M&L for preparing of new steel surfaces & applying two coats of synthetic enamelled paint over a coat of red oxide primer complete all as specified and directed.

M&L for Two coats of synthetic enamel paint on New wooden surface exc 10cm width or girth including preparation complete all as specified and directed.

M&L two Coats of Synthetic Enamel Paint over one coat of primer to steel and iron surfaces of any description, not otherwise described including preparation of new or previously untreated surface complete all as specified and directed.

M&L for one coats of synthetic enamel paint, area exc.10 cm width or girth over Old painted wooden surfaces including preparation of surface complete in all respect as specified and directed.

M&L for preparation old decorated walls & applying one coats of acrylic oil bound distemper complete all as specified and directed.

Supply only Intregal water proofing compound complete all as specified and directed.

RAJ ENTERPRISE (BID ID -3333768)

UNITED ENGINEERS (BID ID -3332696)

KWALITY CONSTRUCTION (BID ID -3333110)

MS AP CONSTRUTION AND CO (BID ID -3333077)

DEEPAK KHATTAR (BID ID -3332737)

MAZUMDER ENTERPRISE (BID ID -3333280)