Loading
Loading…
Loading…
Tender Value
Refer Docs
EMD Value
₹2.0 L
Closing Date
10 Apr 2026, 4:00 pmClosed
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Revenue
17 conditions · 5 needing a document upload
Financial Eligibility Criteria: (Ref: RB letter No. 2022/CE-I/CT/GCC-2022/POLICY : Advance Correction Slip No.-1 dt 14.07.2022) The tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less; where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-I, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
The intending tenderers should possess a valid electrical contractor license at the time of opening of tender, issued by any state government & same should be submitted along with tender documents by all bidders including working contractors of this unit otherwise offer shall be summarily rejected....... IT SHOULD BE NOTED BY THE TENDERER THAT ELECTRICAL LICENSE UNDER RENEWAL AT THE TIME OF TENDER OPENING WILL NOT BE CONSIDERED AND OFFER WILL BE SUMMARILY REJECTED. IT IS THE RESPONSIBILITY OF TENDERER TO UPLOAD VALID ELECTRICAL CONTRACTOR LICENSE ON THE DATE OF TENDER OPENING.
All requisite documents mentioned in clause 3.7 of tender document attached pertaining to constitution of firm/concern. (As applicable).
38 conditions · 4 needing a document upload
The rate to be quoted by tenderer shall be inclusive of all state/central taxes including GST. THE TENDERER SHOULD UPLOAD VALID GST REGISTRATION CERTIFICATE ALONG WITH THE OFFER.
The tender shall comply with General Condition of contract (GCC),2022 of Indian Railways (file attached). and its latest amendment, if any. The tenderer shall submit the offer after duly satisfying himself/herself with the GCC,2022 in general.
Tenderers are required to upload the Bank details as per Annexure-XII (Real Time Gross Saving (RTGS)/National Electronic Fund Transfer (NEFT) Model Mandate Form)of tender document.
Tenderers are required to upload requisite details as per Annexure-VIIB (DETAILS OF CONTRACTUAL PAYMENT RECEIVED IN LAST THREE FINANCIAL YEARS AND CURRENT FINANCIAL YEAR) without which the offer is liable to be rejected.
Tenderers are compulsorily required to upload Affidavit as per Annexure-XXIV along with tender document, without which the offer will be considered incomplete and will be rejected summarily.
All requisite documents/credentials mentioned in clause 3.5 of tender document attached pertaining to his/their technical and financial eligibility. (As applicable).
All requisite documents mentioned in clause 3.7 of tender document attached pertaining to constitution of firm/concern. (As applicable).
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
No post tender correspondence for submission of additional documents shall be entertained after opening of the Technical & Commercial offers. Even suo-moto post tender letters of the tenderer/s shall be treated as Null & Void.
No post tender correspondence for submission of additional documents shall be entertained after opening of the Technical & Commercial offers. Even suo-moto post tender letters of the tenderer/s shall be treated as Null & Void.
The rate to be quoted by tenderer shall be inclusive of all state/central taxes including GST. tenderer shall submit GST certificate along with the offer.
This tender complies with Public Procurement Policy (Make in India) Order 2017, dated 15/06/2017, issued by Department of Industrial Promotion and Policy, Ministry of Commerce, circulated vide Railway Board letter no. 2015/RS(G)/779/5 dated 03/08/2017 and 27/12/2017.
IF ANY DISCREPANCY IS FOUND IN THE TENDER DOCUMENT, NAMELY SOR ITEM DESCRIPTION, SPECIAL TENDER CONDITION ETC., CLARIFICATION CAN BE SOUGHT FROM THE OFFICE OF SRDEE/G/DLI, DRM OFFICE, STATE ENTRY ROAD, NEW DELHI.
This tender complies with Railway Board instructions for Startups (recognized by Department of Industrial Policy and Promotion, Ministry of Commerce and Industry) for exemption from payment of Bid Security as detailed in GCC 2022 as amended from time to time. Such Startup firms may note that no other exemption is applicable to them in this particular tender.
On account payment, contractor shall submitted indemnity bond with validity up to the completion/extended period in the prescribed format (please refer Annexure-XXVIII) at the contractor's cost, vesting the ownership of such material with the railways.
Contractor has to depute sufficient number of efficient manpower to carry out the work in parallel at different sites under scope of instant tender. No any excuses regarding non- availability of material and manpower for carrying out the work concurrently/parallelly at various sites shall be admissible.
The contractor has to submit drawing/plan showing route diagram to consignee for signature of concerned SSEs of other departments. Its required geological survey to be conducted at his own cost to avoid damage of any other cable/Pipe etc.
Since Site of work involves locations across Railway yard and Track in this instant tender ,tenderer should note this Tenderer cannot refuse or delay work on the grounds of less convenient locations . The quoted rate in the tender is assumed to cover all such travel, mobilization, and logistic efforts.
PAYMENT TO THE CONTRACTOR SHALL BE MADE AS UNDER: 1.8.1 i) For all SOR item 1-14 ( except SOR item 7) 100% payment will be done after successful supply, installation, testing and commissioning of actual work done by the tenderer and on certification by the Railway representative. No part payment shall be made for supply of material. (ii) For SOR item 7 :100 % payment will be done after successful supply, installation, testing and commissioning of High Mast only if the corresponding existing conventional type (Lattice type) (in lieu of which instant new High Mast is being installed) of SOR item No 12 , is successfully dismantled and released material is deposited in Railway store(GSD/SSB) as decided by Railway administration . If corresponding existing conventional type (Lattice type) of SOR item No 12 , is not dismantled and released material is not deposited in Railway store(GSD/SSB), Only 80 % payment will be done for SOR item 7 for successful supply, installation, testing and commissioning of High Mast ,Remaining 20% payment will be done for SOR item 7 after corresponding dismantling as per SOR No 12 has been successfully executed .
This tender shall also complies with "Indian Railways Standard General Conditions of Contract, April 2022 (Advance Correction Slip No. 11)" vide Railway Board letter No. 2022/CE-I/CT/GCC-2022/POLICY/Pt.I (E-3320424), dated: 13.03.2026 (attached)
Electrical work regarding provision of High Mast Towers and dismantling of obsolete (Lattice type) High Mast Towers at HNZM, TKD, DEE, MTC, PNP and fencing with rail of existing high mast tower in goods siding over Delhi division.
43-R1-SRDEE-G-DLI-2025-26~NR
43-R1-SRDEE-G-DLI-2025-26
Open
Works - General
6 Months
Delhi, Delhi
₹0
₹2.0 L
10 Apr 2026
21 Mar 2026
27 Mar 2026
29 items across 1 schedule
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| — | — | — | 1,00,19,343 | ||
| — | 50.00 | — | — | ||
| Earthing with 40 mm dia GI pipe class 'B' 4.5 meter long earth electrode as per IS:3043 (latest version)to achieve earth resistance less than 5 ohms including construction of masonry enclosures with hinged cover plate of cast iron with locking arrangement (approx. size 400 mmx 400 mm) on top, provision of earth plate, connections from earth electrode to switch gear/pole as per drawing & as per explanatory note. | — | — | — | 2,87,550 | |
| — | 500.00 | — | — | ||
| Supplying and laying 8 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required as per IS 3043 (latest version) and as per explanatory note. | — | — | — | 5,000 | |
| — | 250.00 | — | — | ||
| Supplying and laying 25 mm X 5 mm G.I strip confirming to relevant IS as per IS:3043 (Latest version), fixing on surface or as per site condition, clamping or fixing with suitable arrangement as per site requirement, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50 mm) & as per explanatory note. | — | — | — | 38,500 | |
| — | 4000.00 | — | — | ||
| Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation(upto 75-100 cm depth and not less than 35 cm wide ), sand cushioning, protective covering and refilling the trench etc. as required as per detail drawing approved by competent authority and conforming to IS 1255 (Reviewed in 2016) or latest & as per explanatory note. Upto 35 sq. mm | — | — | — | 14,08,000 | |
| — | 1000.00 | — | — | ||
| Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground in the same trench in one tier horizontal formation including excavation(upto 75-100 cm depth and not less than 55 cm wide & maintaining gap not less than 20 cm between the cables), sand cushioning, protective covering and refilling the trench etc. as required as per detail drawing approved by competent authority and conforming to IS 1255 (Reviewed in 2016) or latest and explanatory note. Upto 35 sq. mm | — | — | — | 2,88,000 | |
| — | 1000.00 | — | — | ||
| Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required. In case of any demolition of PCC, RCC, road, wall surface etc. the contractor should ensure repairing of the same on own expenses as per site requirement and satisfaction of railway representative conforming to IS 1255 (Reviewed in 2016) or latest & as per explanatory note. Upto 35 sq. mm (clamped with 1mm thick saddle) | — | — | — | 59,000 | |
| — | 20.00 | — | — | ||
| Supply, Eraction, Testing & Commissioning of 16 meter high mast system suitable for 9 Nos. LED flood light luminaries with the help of suitable equipment including accessories & control panel for high mast system as per Tech Spec IV , shall have provision of RCBO in place of MCB from I/C side .Each high mast shall also have one twin dome aviation obstruction light with 2 nos. LED lamp of Make BAJAJ, Osram, PHILIPS, GE or equivalent ; conforming to IS 875 (Part 3) (latest version) for wind load considerations, IS 2062 (latest version): For structural steel used in pole fabrication, IS 17740 :2022 (or latest ) : For high mast lighting system design and installation . | — | — | — | 49,03,840 | |
| — | 180.00 | — | — | ||
| Supply, fixing, testing and commissioning of 150-155 watt LED based flood light luminary with cool white light, pressure die cast aluminum housing, IP 66 or better having system complete conforming to CEE/NR's spec. No. CEE/NR's spec. No. CEE/NR/121-Elect/PS/2018 (Rev- '3') or latest as Tech Spec-I attached & PCEE/NR's spec. No. PCEE/NR/121- Elect/PS/2019 (Rev- '4') as Tech Spec-II attached or latest & as per explanatory note. | — | — | — | 12,69,000 | |
| — | 20.00 | — | — | ||
| Supply, Fixing, Testing & Commissioning of astronomical timer based control panel for High Mast tower lighting suitable for 25A 4P contactor as per model No. Alpha Rex3 D21, 1 channel Cat Part 412654 of Legrand or equivalent. Panel should be double door weather proof type complete and conforming to IEC 61439-1 & 2, IEC 60947 or latest and as per explanatory note. | — | — | — | 1,89,580 | |
| — | 20.00 | — | — | ||
| Fabrication, supply and erection of Fencing around the high mast in square shape size 2M x 2M and height 1.5M from ground level fabricated from MS angle size 40x40x6mm, MS Flat size 40x6mm and wire mesh made of 8SWG wire and 1M wide hinged type lockable door as per drawing approved by Railway including grouting, CC platform around the high mast above 0.30M above ground level and painting,danger plate etc. complete as per site requirement and as per explanatory note. | — | — | — | 1,44,600 | |
| — | 5.00 | — | — | ||
| Design, Supply, fixing, testing and commissioning of front operated double door type weather proof outdoor type feeder pillar having IP 65 protection (MCCB - Incoming & MCCB - Outgoing) comprising with the following MCCB's fixed in it of make: Siemens, L&T, Schneider, Legrand or equivalent conforming to IEC 60947 or latest with digital measuring instrument & bus-bar arrangement confirming IS, IE rules and site requirement. 4P MCCB 250Amps 36 kA with adjustable thermal & fixed magnetic release = 01 No. (Incoming). 4P MCCB 125Amps 36 kA with adjustable thermal & fixed magnetic release = 02 No. (outgoing). 4P MCCB 63Amps 36 kA with adjustable thermal & fixed magnetic release = 04 No. (outgoing). It should come with anti corrosion protection, should be rodent entry proof with proper cable glands for incoming and outgoing. Minimum clearance = 8 mm (between phases, or phase-to-earth in air). Minimum creepage = 14 mm (along insulation surface). If used in high pollution environments (PD4, e.g. coastal area, cement plants) creepage requirement increases as per the IEC specification. It must comply with IEC 61439 performance tests for mechanical strength, corrosion resistance, IP/IK rating, and thermal stability and as per explanatory note. | — | — | — | 5,39,545 | |
| — | 4.00 | — | — | ||
| Dismantling of existing conventional type (Lattice type) high mast tower complete with all accessories and depositing the released material in the Railway store(GSD/SSB) as decided by Railway administration including transportation of all the material from site and as per explanatory note. | — | — | — | 79,228 | |
| — | 3.00 | — | — | ||
| Supply, installation, casting and commissioning of RCC foundation for 16-30 m high mast system, along with erection of foundation suitable bolt manufacture from special steel along with nuts, washer , anchor plate and tempates, considering the safe soil bearing capacity at site as 10 T/sq.mtr Depth as per approved foundation structure design should be as per High mast OEM as per technical scope of work.This work also includes transportation of HMT from one location to the new location identified for shifting as per site requirement and as per explanatory note. | — | — | — | 2,70,000 | |
| — | 500.00 | — | — | ||
| Supply, Laying, Testing & Commissioning of HDPE pipe of 160 mm dia having material grade PE-100, wall thickness PN-6 and confirming to IS-4984 or latest as per IE rules and site requirement for cable laying through HDPE pipe of 160mm diameter by trenchless method as per IS -1255 or latest & IE rules and site requirement and as per explanatory note. | — | — | — | 5,37,500 |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
uploadhighmasttechspec4.pdf
ATTACHMENT
GCC-2022-ACS10_merged.pdf
ATTACHMENT
TECHSPEC-I_1.pdf
ATTACHMENT
TECHSPEC-II.pdf
ATTACHMENT
2026_03_13IndianRailwaysStandardGeneralConditionsofContractApril2022AdvanceCorrectionSlipNo_111.pdf
ATTACHMENT
TenderDocument-43-R1.pdf
ATTACHMENT
ExplanatoryNote-43-R1.pdf
ATTACHMENT
Specialconditions-43-R1.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .