erection of UG cable and link line in 33KV CG pudhur SS

Clearing scrub jungle

Earth work excavating and depositing on bank with initial lead of 10m & initial lift of 2m in Hard stiff clay, stiff black cotton, hard red earth, shales, murrum, gravel stoney earth and earth mixed with small size boulders SS 20B.

Dewatering the cable trench / duct using 5.00 HP diesel pumpset wherever necessary including hire charge for Tools & Plants, labour lead and lifts etc complete.

Providing crusher dust instead of sand bedding with good quality to a depth upto 150mm (6") including cost of materials, labour, leads and lifts etc.., complete

Refilling with excavated earth, consolidating in layers and the top brought for line with the existing surface including cost of labour lead lift etc.., complete.

Supplying of 11 KV RCC"V"troughs and laying over the UG cable to proper grade and alignment inside the cable trench, printing letters of not less than 75mm on either side of the troughs as directed by the Engineer incharge of works including the cost for all materials , transporting of troughs from the source to the destination upto 10kms stenciling,paints,brushes all leads and lifts etc.,complete.

Uncoiling and laying of 11 KV, 3x300 sqmm HT UG cable in the excavated trench including drawing the cable through RCC/GI/PVC pipes wherever necessary at road crossings etc.., without any damage/including transporting of cables tools and plants, labour. lead lift etc., complete.

Cutting the cable of required length and sealing the ends with suitable end caps for 11KV XLPE cables, including cost of all materials, tools and paints, leads and lifts etc., complete.

Transporting of the remains of the empty cable drums (iron materials) to the stores for devolution including loading and unloading , leads and lifts etc.., complete.

Supply of erection of cable marker in RCC(1:2:4) using 20mm HBs metal of size 0.3x0.60m and of 100mm thickness engraving letters of "TANGEDCO UG Cable painting the engraved letters , fixing the cable marker in a bed of PCC (1:3:6) using 20mm HBs metal of size 0. 0.45X0.30X0.45 m including cost of all materials,labour, transporting to the destination all leads and lifts etc.,complete.

Providing watch and ward required at site as directed by the Engineer incharge.

Providing Barrycade arrangements while execution of work

Erection of 11 KV, 3x300 sqmm Outdoor end termination kit

UG cable earthing by coil earthing

Loading & unloading of PSC / RCC poles 9 m & above

Loading & unloading of RSJ Pole

Transporting of RCC / RSJ / PSC / fabricated pole from road side to pole pit head

Transporting of Line Materials from Sub-stores to section pocket or near the work spot at Road side using private vehicle other than bullock cart with load of one M.T minimum/vice versa (upto 8 km)

Transporting of Line Materials from Sub-stores to section pocket or near the work spot at Road side using private vehicle other than bullock cart with load of one M.T minimum/vice versa (above 8 km)

Excavation & back filling of pole pit for poles 9 m (30') and above per location

Erection of poles PSC / RCC poles 9 m & above

Erection of poles RSJ 9 m & above

Fixing of Tapping Channel Cross Arm

Fixing of V Cross Arm, 3.5 ft

Fixing of 11 KV Pin Insulator (Porcelain / Polymer)

Fixing of 11 KV Disc with Metal Parts

Fixing of TI Fitting

Sleeve Concreting of pole including cost of cement, sand & jally with a mixture of 1:3:6, including all materials

Paving of conductor, stringing binding jumpering complete with ACSR / AAAC 7/2.50 or 7/2.59 (Weasel) per KM

Excavation & back filling of stay pit for poles 9 m (30') and above

Erection of stay set complete

Earthing of pole with wire including burying loop and binding

Erection of Top Channel for DP Structure

Erection of 11 KV AB Switch

Earthing of DP Structure

Dismantling of PSC Pole 7.5 m

Dismantling of ACSR 7/2.59 mm

Dismantling of ACSR 7/3.35 mm

Dismantling & Re-erection of LT 3 Phase Cross Arm

Dismantling & Re-erection of LT Single Phase Cross Arm

Dismantling & Re-erection of ACSR 7/3.35 mm

Dismantling & Re-erection of ACSR 7/2.59 mm

Dismantling & Re-erection of LT Pin & Insulator

Dismantling & Re-erection of Aluminium Knob

Dismantling & Re-erection of LT Shackle

Dismantling & Re-erection of Stay Set Complete

Dismantling & Re-erection of Street Light Complete Set