Civil and Sanitary Group A(Inside Hospital) at SKIMS Soura

Amount

Earth work in excavation by manual means in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed lead upto 50 meters beyond 1m from cutting edge. All kinds of soil :

Extra for every additional lift of 1.5 m or part thereof in excavation/banking excavated or stacked material :( All kinds of soil :)

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m.

Supplying and filling in plinth with fine sand under floors including, watering, ramming, consolidating and dressing complete from surface drains and disposal.

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering including all carryings.

(A) 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

(B)1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size)

(C) 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)

Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) including all carriage.

Centering and shuttering including strutting, propping etc. and removal of form for any locations such as foundation footings, columns, walls, suspended floors, roofs, landing balconies, shelves ,lentils ,beams, pillars stair etc.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete.Thermo-Mechanically Treated bars of grade Fe-450 or more.

Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including all carriage :

(A)Cement mortar 1:4 ( 1 cement : 4 coarse sand)

(B)Cement mortar 1:6 ( 1 cement : 6 coarse sand)

Half brick masonry with common burnt clay (non-modular) bricks of class designation 7.5 in foundations and plinth including all carriage

(a) Cement mortar 1:3 ( 1 cement : 3 coarse sand)

(b)Cement mortar 1:4 ( 1 cement : 4 coarse sand)

Providing and fixing gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:3 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels (18mm thick).including moulding of edges(Granite of any color or shade) as approved by Engineer-incharge

Providing hoisting and fixing trusses/purlins /rafters/posts/ post-plates/ceiling joists,frame work and or like components.(First class Budloo wood)

Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters(40 mm)(with ISI marked M.S pressed butt hinges bright finished orrequired size with necessary screws)

Providing and fixing glazed shutters for doors, windows and clerestory windows using 3.5 to mm to 4 mm thick float glass panes including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws.( First class deodar wood) 40 mm.

Providing and fixing wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction of Engineer-in-charge (40 mm thk).First class deodar wood

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15 cm 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size).

Providing and fixing ISI marked aluminum butt hinges ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete :

(a)125x75x4 mm

(b)125x63x4 mm

(d) 100x63x4 mm

(e)75x63x4 mm

Providing and fixing aluminum tower bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete :

Providing and fixing aluminum handles ISI marked anodized (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade with necessary screws etc. complete.

Providing and fixing wooden moulded cornice beading triangular shape to the junction/corner/edges of paneling etc. with iron nails screws, plugs and priming coat on unexposed surface etc. complete. (First class kail wood).

P/F 40mm*6mm ply lipping

Providing and fixing deoder wood lipping/moulded beading of size 35x5mm fixed with wooden adhesive of approved quality and screws/nails on the edges of the pre laminated particle board as per directions of the engineer-in-charge.

Providing and fixing bright finished 100mm mortice lock with 6 levers for aluminum doors of approved quality with necessary screws etc. complete as per direction of Engineer-in-charge.

Providing and fixing magnetic catcher of approved quality in cupboard/wardrobe shutters including fixing with necessary screws etc. complete. (Godrej/link)

Structural steel work in built up sections, trusses. Frames, gratings, guard bar, ladder, railing, brackets, and similar work. Including cutting, hoisting, fixing in position welded and applying a priming coat of approved steel primer all complete.

Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2mm and braced with flat iron diagonals 20x5 mm size,with top and bottom rail of T-iron 40x40x6mm, with 40mm dia, steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles,including applying a priming coat of approved steel primer(complete job)

Cement concrete flooring 1:2:4 (1cement: 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry and curing complete, but excluding the cost of nosing of steps etc.complete.

Kota stone slab flooring 20 -25 mm thick over 25mm (average) thick 1:4 cement mortar base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing, polishing and curing.

Providing and fixing Ist quality ceramic glazed wall tiles of approved make, in all colours, shades(of 7-8 mm thick and size 300*450mm and above) as approved by Engineer- in-Charge, in walls, skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying nonskid Glazed Ceramic floor tiles of size 300x300 mm or more ,8-10 mm thick of 1st quality of approved make, laid on 20 mm thick cement mortar 1:3 (1 Cement : 3 Coarse sand), including grouting the joints with white cement and matching pigments etc., complete.

Providing and laying vitrified floor tiles in different sizes of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete.(10 mm)( Size of tile 600x600 mm)

Providing corrugated G. S. sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (upto any pitch in horizontal/vertical or curved surface)excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required

(a)0.63 mm thick with zinc coating not less than 275 gram/m2

b) 0.50 mm thick with zinc coating not less than 275 gram/m2

P/L 15 mm thick Cement plaster of mix:

(a) 1 : 4 ( 1 cement : 4 coarse sand)

b)1 : 6 ( 1 cement : 6 coarse sand)

Pebble dash plaster upto 30m height above ground level with a mixture of washed pebble or crushed stone 6mm to 12.5mm nominal size dashed over and including fresh plaster in two layers, under layer 12mm cement plaster 1:4 (1 cement: 4 Coarse sand) and top layer 10mm cement plaster with cement mortar 1:3 (1 cement: 3 fine sand) mixed with 10% finely grounded hydrated lime by volume of cement.including all scafolding etc complete job.

Providing and applying POP/ putty of 2mm thickness over plastered surface to prepare the surface even and smooth complete.

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface.

Applying priming coat:

(a) With ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood).

b) With ready mixed red oxide Zinc Chromate primer of approved brand and manufacture on steel work

Wall Painting with plastic emulsion paint of approved brand and manufacture to give an even shade. Two or more coats on new work.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade.(two or more coats on new work)

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade, one or more coats on old work.

Removing white or colour wash/dry distember/paint by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade, one or more coats on old work.

Renewing glass panes, with wooden fillets and nails wherever necessary

(a) Float glass panes of thickness 3.5mm to 4 mm thickness

(b) Float glass panes of thickness 5 mm

Demolishing cement concrete manually/mechanical means including disposal of material within 500 meters lead as per direction of Engineer-incharge:(1:3:6 or richer mix (i/c equivalent design mix) Demolishing R.C.C. work manually/by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 meters lead as per direction of Engineer-in-charge. Extra for cutting reinforcement bars manually/by mechanical means in R.C.C. or R.B. work (Payment shall be made on the cross sectional areas of R.C.C. or R.B. work) as per direction of Engineer-in-charge.

Demolishing R.C.C. work manually/mechanical means including stacking of steel bars and disposal of unserviceable material within 50 0meters lead as per direction of Engineer-in-charge.

Demolishing brick work manually/mechanical means including stacking of serviceable material and disposal of unserviceable material within 500 meters lead as per direction of Engineer-in-charge: (In cement mortar)

Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 500 meters lead :

Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 500 meters lead.

(Dismantling tile/kota work in floors,walls and roofs laid in cement mortar including disposal of material within 500 meters lead

Dismantling C.G.I roofing including ridges, hips valleys and gutters etc., and stacking the material within 500 meters lead.

Dismantling old plaster or skirting, raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 500 meters lead.

Supplying stacking and laying of good earth at site including spreading,levelling watering in layers and consolidated with hand rolling.

P/F white vitreous chins flat back or wall corner type lipped front urinal basin 430*260*350mm and 340*410*265 mm sizes respectively with flushing cistern with standard flush pipe and C.P brass spreaders with brass unions and G.I clamps complete including fittings and brackets cutting and making good the walls and floors and wherever required. (1 urinal basin with 5 litre white P.V.C flushing cistern.

(a)white vitrous indian type W.C (Orisa pattern) size 580*440mm with integrated foot rest

(b)European type W.C with white solid plastic seat and lid

© white solid plastic seat and lid

d)10 lit low level P.V C flushing cistern

(e) C.Plong bend 32 mm dia

(f)white vitrouschina pedestal for wash basin

p/f of C.P fittings and fixtures

( a)bib cock long body

(b)bib cock short body

(c)pillar cock

(d)wall mixer(two holes)

(e)wall mixer with showers

(f)P V C corner shelves

(g)sink mixer (single hole)

(h)grating 100 mm

(i)C.P tube 45-60 cm

(j)towl ring 8-9 inches

(k)cloth hanger

(l)soap case

(k)mixer leg

(m)towl rod 60 cm

Providing and fixing G.I. pipes complete with G.I. fittings and clamps,including cutting and making good the walls etc.(EXTERNAL)

(A):(medium Grade )

(i)15 mm dia. nominal bore

ii) 20 mm dia. nominal bore

(iii)25 mm dia. nominal bore

(iv)32 mm dia. nominal bore

(v)40 mm dia. nominal bore

(B)Concelead type including cutting chasses and making giood the walls

(i) )15 mm dia. nominal bore

(ii)20 mm dia. nominal bore

(v)25 mm dia. nominal bore

Providing and fixing brass bib cock of approved quality.

(a) 25 mm nominal bore

(b) 32 mm nominal bore

(c) 40 mm nominal bore

Providing and fixing brass stop cock of approved quality.

(a) 15 mm nominal bore

(a) 20 mm nominal bore

(a) 25 mm nominal bore

(a) 32 mm nominal bore

(b) 40 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end)

(a) 25 mm nominal bore

(b) 20 mm nominal bore

©32 mm nominal bore

(d)40 mm nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete

(a)15 mm nominal bore

(b) 20 mm nominal bore

©32 mm nominal bore

(d)40 mm nominal bore

Providing and fixing gun metal non-return valve of approved quality(screwed end)

(a) 25 mm nominal bore

(b) 32 mm nominal bore

©32 mm nominal bore

(d)40 mm nominal bore

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet

(a) 100 mm diameter

(b) 150 mm diameter

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete .

(a) 15 mm nominal bore

(b) 20 mm nominal bore

©32 mm nominal bore

(d)40 mm nominal bore

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank

Providing and fixing powder coated aluminum work for doors, windows, ventilators andpartitions with extruded built up standard tubular sections/appropriate Zsections and other sections of approved make conforming to IS: 733 and IS: 1285, fixed with dash fastener of required dia. and size including necessary filling up of gaps at junctions i.e, at top, bottom and sides withrequired EPDM rubber / neoprene gasket felt etc. Aluminum sections shall be smooth, rust free, straight, mitred and jointed mechanicallywherever required including cleat angle, Aluminum snap beading forglazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge (glazing,panelling and dash fasteners to be paid for separately.)frames/shutters.

Providing and fixing glazing in aluminum door, window, ventilator Shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineerin-Charge. (Cost of aluminum snap beading shall be paid in basic item.)

(a) With floating glass panes of 3.5to 4.0 mm thickness (weight not less than 10.00 kg / sqm)

(b) With float glass panes of 5.0 mm thickness (weight not less than 12.50 kg / sqm)

p/f of galvanizes m.s wire guaze with 0.63 mm thk wire of complete

p/f G.I crossover(15 mm)

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes channels, plates etc. including welding ,grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete ,including fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts etc. of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

P/L of stone soling of required sizes , compacting , watering and ramming, complete(net measured quantity shall be deducted 15% for voids)

P/F of 19mm thick board of approved quality and manufacture in shelves , partitions, tables, access panel , shutters and other shutters etc. fixed with nails/ wood screws complete finished area to be measures and paid.

(a)water proof

(b) Commercial

P/F of 6 mm thick ( 3- Ply ) commercial plywood of approved make and manufacture in all types of work fixed with nails and wood screws finished area to be measures and paid

P/F of 12 mm thick ( 3- Ply ) commercial plywood of approved make and manufacuture in all types of work fixed with nails and wood screws finished area to be measures and paid

P/F of lamination of approved quality and manufacture and of required shade and colour fixed with standard quality of adhesive in all types of works ( fitted and finished area to be measures and paid including cost of adhesive etc. complete in all respects.

(a)0.8 mm thick plain

(b)1 mm thick plain

(c) 1 mm thick textured.

P/F 20x12 mm ornamental kail wood beading fixed with nails / wood screws complete.

P/F of Flat pressed 3-layer pre-limanited Board(Lamination on both sides) of approved quality inluding cost of screws/adhesive complete.

a. 12mm thick

b. 18mm thick

P/F of hardware fittings of approved quality ISI make including fixing with necessary screws , nuts, bolts etc complete , ( approved ones )

a. Link Lock 11” long

b. Link Lock 8” long

p/f Ornamental heavy handle 150 mm (approved one ) aluminum base finished in required shade

p/f Ornamental heavy handle 200 mm (approved one ) aluminum base finished in required shade

p/f Ornamental handle 100 mm ( approved one ) aluminum base finished in required shade.

p/fOrnamental handle 75 mm ( approved one ) aluminum base finished in required shade

p/f Ornamental handle 55 mm ( approved one ) aluminum base finished in required shade.

. p/f Plastic beading 25 mm ( approved one )

p/f Multi purpose locks of required size approved one ( link ) or equalant .

Regrinding / polishing of mosaic/quota and marble flooring / skirting including repairs of cracks / ages including rubbing , polishing materials , tools , plants , machinery involved complete and disposal of residue.

P/L of Kerb stones 150 mm and 300 mm deep size chisel dressed on top and sizes of required length in 1:4 mix and pointing with cement morter 1:2 mix.

(a)Providing and Fixing

(b)Fixing only

P/F of pre- cast cement concrete tile with locking pavers of m-30 grade having crushed/ Nalla stone aggregate 12.5 mm and below with dolomite anti wear topping laid over a well consolidated and evenly spread 40 mm thick sand bed and grouting the joints with sand and consolidating the paving using a plate vibrator incl. all wastages cast of all materials leads, lifts , loading , unloading , T&P and machinery complete ( finished work to be measured and paid ) incl. side jamming in 1:2:4 ratio cement concrete as required.

Providing , fitting , spreading of GSB filling ( Nallah Muck ) from approved source including watering , compacting and rolling in 200 mm layers complete.(5% shrinkage for net measurement)

P/F of aluminum composite pannel sheetsapproved make(complete job)

3 mm thick

5 mm thick

P/F heavy duty ball cock with 300 mm brass rod and ball complete incl.removing damaged one where ever required.

P/F of PVC heavy duty ball cock to fit into all kinds of flush tanks (compact one) of standard make (approved one)15mm dia

P/F of CP waist for steel sinks heavy duty

a. 50mm dia

b. 75mm dia

c. 100mm dia

Providing of CP Knob (Gem/Parko)

P/F C.I Pipesand Fittings

(A) pipes

(B) Plain bend

©.door bend

(D) reducer

(E).Cowl

b. 50mm dia

(F)coller

P/F of spindle heavy duty type for mixer and bib cock (Gem/Parko) fittings including removing old damaged one where ever required (Approved one)

P/F of CP Urinal spreader heavy quality

P/F of PVC pipes of prince make or equalent (ISI quality of following dia metre

(A) Pipes

(B) door bend

(B) plain bend

© Coller

D)Elbow

p/f health fauset with 1 mm cp chain

P/F of M.S Push cocks 15mm complete (approved one)

P/F of C.I manhole covers with frame (heavy duty ) approved ones of required shape and size

a.600x600mm dia

b.450x450mm dia

c.300*300 mm dia

P/F of high neck swan type C.P mixers Jacquar / approved one with hot / cold controls.

P/F of elbow action C.P mixers of approved make

P/F of G.I assorted fittings of nominal bore of ISI make heavy quality including dismantling including removing of old one wherever required (approved one

A. 15mm nominal bore

a. Socket

b. Elbow

d. Plug

e. Nipple 75 mm long

f. Niple 100 Mm long

g. Tankey Nipple

B. 20 mm Nominal Bore

a. Socket

b. Elbow

d. Plug

e. Nipple 75 mm long

f. Niple 100 Mm long

g. Tankey Nipple

C. 25 mm Nominal Bore

a. Socket

b. Elbow

d. Plug

e. Nipple 75 mm long

f. Niple 100 Mm long

g. Tankey Nipple

Insulation of supply lines by way of applying of non- wound fully with chiken wire mesh beneath, 6 mm coat of POP/ cement finished smooth without undulations complete including glass wool to be approved)

a. 15 mm dia

b. 20 mm dia

c. 25 mm dia

d. 32 mm dia

e. 40 mm dia

P/F of imported Wooden Laminated Flooring of Approved pattern and Brand/Make in desired colour

a.8MM Thick for walls

b.12 MM Thick for floors

p/f wall paper of superior quality(sample to be approved by engineer-in charge)

Khatam bandh ceiling of approved pattern and brand/make

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone- III) : 8 graded stone aggregate 40 mm nominal size),inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :

Inside size 90x80 cm and 45 cm deep including C.I. cover with frame

Inside size 90x80 cm and 60 cm deep including C.I. cover with frame

Inside size 120x90 cm and 90 cm deep including C.I. cover with frame

Supply of Labour for Snow /drain /road clearance

Exta cost for lead cocked joints for C.I pipe

TEHSEEN CONSTRUCTIONS PVT. LTD.

MOHAMMAD YASEEN MIR

M/S M.I.CONSTRUCTION