SPECIAL REPAIRS TO BLDG NO. OWT-169 OWT-170 STORE SHELTER OF MH, SPECIAL REPAIRS TO BLDG NO. OWT-31 OWT-32 JCOS LIVING SHELTER OF DOU, PROVN OF LPG STORE AT MH AND PROVN OF CERTAIN MINOR WORKS AT DIFFERENT LOCATIONS OF LIKABALI MIL STN UNDER GE 8

Amount

B/R SERVICES/WORKS

Demolition Cement Concrete (Un-reinforced) in Ground Floors and Pavings, not exc. 150mm thickness (below or above Ground Level) and Removing debris, etc. to a distance not exc. 100.00 Metre, complete all as specified and as directed.

Demolition Brick Work or Pre-cast Concrete Block Masonry, built in Cement Mortar and in any Position including all Quoins, Arches and Pillars, etc., complete all as specified and as directed.

Dismantling Timber Scantlings 40 Sq Cm and Over in Section in Unframed Work, complete all as specified and as directed.

Dismantling Timber Fillets, Rails, Posts, Rafters, Purlins, etc. Under 40 Sq. Cm in Section in Framed Work, complete all as specified and as directed.

Taking down Shutter of any description exc. 1.00 Square Metre and not exc. 2.00 Square Metre Each, complete all as specified and as directed.

Taking down/out Unserviceable Rusted/Worn out Wire Cloth/Netting of any description, fixed with Beads, etc., complete all as specified and as directed.

Hacking out Old Broken Glass (any thickness, size, quality or description) from Wooden or Metal Frame or Stone, Concrete or Brick surrounds including hacking out old Putty or removing Beads, etc., punching or drilling out old Glazing Pins/ Spring Clips, complete all as specified and as directed.

Dismantling Plain or Corrugated Steel Sheeting of any gauge and thickness, Segrega-ting the Serviceable Plain or Corrugated Steel Sheeting and Stacking properly at Sites and Keep in Safe Custody for re-use, complete all as specified and as directed.

Dismantling Wall and Ceiling Boards (Fibre, Pulp, Insulation, etc.) or Insulation Boards/ Slabs/ Blankets of any descriptions including Cover Fillets, complete all as specified and as directed.

Dismantling Floor, Hearth or Wall Tiling including Cement Mortar Bedding (but not backing) and Removing debris, etc. to a distance not exc. 100.00 Metre, complete all as specified and as directed.

Taking down Cement Plaster including Raking out Joints, Hacking for Key, scrubbing down with Water and Removing Debris, etc. etc. to a distance not exc. 100.00 Metre, complete all as specified and as directed.

Surface Dressing not exc. 15 Cm Deep in Soft/ Loose Soil and getting out, complete all as specified and as directed.

Surface Excavation not exc. 30 Cm Deep and ave. 15 Cm Deep in Soft/ Loose Soil and getting out, complete all as specified and as directed.

Excavation in Over Areas, not exc. 1.50 Metre in depth and getting out as in Soft/ Loose Soil, complete all as specified and as directed.

Excavation in Over Areas, exc. 1.50 Metre but not exc. 3.00 Metre in depth and getting out as in Soft/ Loose Soil, complete all as specified and as directed.

Excavation in Trenches not exc. 1.50 Metre wide and not exc. 1.50 Metre in depth for Foundation etc. or for Shafts, Wells, Cess Pits, Manholes, Pier Holes, etc. not exc. 10 Sqm on Plan and not exc. 1.50 Metre in depth and getting out as in Soft/ Loose Soil, complete all as specified and as directed.

Returning, Filling in including Spreading, Levelling, Watering and Well Ramming in layers not exc. 25 Cm, in Soft/Loose Soil, complete all as specified and as directed.

Removing Excavated Materials (Soils) to a distance not exc. 50.00 Metre and depositing where directed at a level not exc. 1.50 Metre above the Starting Point, complete all as specified and as directed.

Excavating in Post Holes (or Similar Holes) in Soft/Loose Soil, Each not exc. 0.50 CUM, getting out and Removing Surplus Soil to a distance not exc. 50.00 Metre and Making Good Surfaces, complete all as specified and as directed.

M&L Sand (as approved) Filling under Floors or in Foundations in layers not exc. 15 Cm thick including Watering and Consolidation, complete all as specified and as directed.

M&L Hardcore broken Stone or Boulders, gauge not exc. 63mm, deposited, spread and levelled in layers not exc. 15 Cm thick, watered and well rammed to a True surface, complete all as specified and as directed.

M&L Loose Filling with using Broken Brick Aggregates of Gauge 80mm to 150mm in Soakage Pits/ Soakage Wells, etc., complete all as specified and as directed.

M&L Cement Concrete 1:3:6 (40mm graded aggregate) for embedding Mild Steel Work as Posts, etc. in Foundations, Filling and Mass Concrete, etc. including necessary Formwork, complete all as specified and as directed. NOTE : Cost of Formwork will deem to be include in the Quoted Unit Rate.

M&L Cement Concrete 1:4:8 (40mm graded aggregate) in Foundations, Filling and Mass Concrete, etc. including necessary Formwork, complete all as specified and as directed. NOTE : Cost of Formwork will deem to be include in the Quoted Unit Rate.

M&L Cement Concrete 1:2:4 (20mm graded stone aggregate) in Lintels upto 1.50 Metre Clear Span, Cills, Steps; Seismic and other Similar Bands, Plinth Courses, String Courses, Lacing Courses, Parapets and Railings upto 60 CM in Height, Copings, Kneelers, Apex Stones, Bed Plates, Holdfats, Filling Back of Steel Door Frames, Kerbs, Water Troughs and the like including weathering, slightly rounded or chamfered angles and throating, etc. including necessary Formwork, complete all as specified and as directed. NOTE : Cost of Formwork will deem to be include in the Quoted Unit Rate.

M&L Cement Concrete 1:3:6 (20mm graded stone aggregate) in Lintels upto 1.50 Metre Clear Span, Cills, Steps; Seismic and other Similar Bands, Plinth Courses, String Courses, Lacing Courses, Parapets and Railings upto 60 CM in Height, Copings, Kneelers, Apex Stones, Bed Plates, Holdfats, Filling Back of Steel Door Frames, Kerbs, Water Troughs and the like including weathering, slightly rounded or chamfered angles and throating, etc. including necessary Formwork, complete all as specified and as directed. NOTE : Cost of Formwork will deem to be include in the Quoted Unit Rate.

M&L Reinforced Cement Concrete 1:2:4 (20mm graded stone aggregate) in Foundation including Rafts, Footing, Foundation Beams for Column Basement Slab, under reamed Piles, complete all as specified and as directed. NOTE : Reinforcement & Formwork will be Measured and Paid for separately under appropriate Items.

M&L Reinforced Cement Concrete 1:2:4 (20mm graded stone aggregate) in Columns, Pillars, Piers, Posts and Struts, etc., complete all as specified and as directed. NOTE : Reinforcement & Formwork will be Measured and Paid for separately under appropriate Items.

M&L Reinforced Cement Concrete 1:2:4 (20mm graded stone aggregate) in Walls, Retaining Walls, Basement Walls, Ballast Walls and the like; any thickness; above Top of Footings; including attached Pilaster and Buttresses, complete all as specified and as directed. NOTE: Reinforcement will be Measured and Paid for separately under appropriate Items.

M&L Reinforced Cement Concrete 1:2:4 (20mm graded stone aggregate) in Beams, Cantilevers, Bressumers, Lintels over 1.50 Metre Span, etc., complete all as specified and as directed. NOTE : Reinforcement & Formwork will be Measured and Paid for separately under appropriate Items.

M&L Reinforced Cement Concrete 1:2:4 (20mm graded stone aggregate) in Slabs supported on Walls, Beams and Columns in Floors of Water Tanks, Roofs, Landings, Balconies, Canopies, Deck Slabs and in Shelves and the like, complete all as specified and as directed. NOTE : Reinforcement & Formwork will be Measured and Paid for separately under appropriate Items.

M&L Pre-cast Reinforced Cement Concrete 1:2:4 (20mm graded aggregate) in Landings, Cover Slabs (for Manholes, etc.), Chullah Hoods, Chajjas, Water Troughs, Mangers, Shelves and Similar Articles with Plain faces and Setting in Cement Morter 1:4, complete all as specified and as directed. NOTE : Reinforcement will be Measured and Paid for separately under appropriate Items.

M&L Formwork to Sides of Concrete Foundations, Footings, Bases of Columns, Raft and Raft Beams, Sides and Soffits (if any) of Foundation and Plinth Beams; and Similar Work; Vertical or to Batter, Flat, Rough Finished surfaces of Concrete, complete all as specified and as directed.

M&L Formwork to Sides of Pillars, Posts, Struts, Piers, Columns and Stanchions, Flat, Rough Finished surfaces of Concrete, complete all as specified and as directed.

M&L Formwork to Faces of Walls, Retaining Walls, Abutments, Parapets and Staircase Railings and Similar Work including attached Pillasters, Buttresses, etc.; Vertical or to Batter, Flat, Rough Finished surfaces of Concrete, complete all as specified and as directed.

M&L Formwork to Sides and Soffits of Floor or Roof Beams, Girders, Beam Haunchings, Lintels, Cantilevers, Shelves including Supports, Overhangs, etc. also splays between Floors and Beams, etc., Flat, Rough Finished surfaces of Concrete, complete all as specified and as directed.

M&L Formwork to Soffits of Suspended Slabs such as Roof Slabs, Floor Slabs, Landings and Similar Works; not exc. 200mm thick (Horizontal or Sloping), etc., Rough Finished surfaces of Concrete, complete all as specified and as directed.

M&L Pre-cast Cement Concrete Block Masonry with Solid Blocks of Size 300x200x200mm or 300x200x100mm, having Compressive Strength of not less than 100 Kg/ Sq Cm (as per IS-2185) in Cement Concrete 1:3:6 (20mm graded stone aggre- gate), exc. 10 Cm in Width and Setting in Cement Mortar 1:6, complete all as specified and as directed.

M&L Pre-cast Cement Concrete Block Masonry with Solid Blocks of Size 300x200x200mm or 300x200x100mm, having Compressive Strength of not less than 100 Kg/ Sq Cm (as per IS-2185) in Cement Concrete 1:3:6 (20mm graded stone aggre- gate), 10 Cm in Width and Setting in Cement Mortar 1:4, complete all as specified and as directed.

M&L Pre-cast Cement Concrete Block Masonry in Honey Combing Wall with Solid Blocks of Size 300x200x200mm or 300x200x100mm, having Compressive Strength of not less than 100 Kg/ Sq Cm (as per IS-2185) in Cement Concrete 1:3:6 (20mm graded stone aggregate), exc. 10 Cm in Width and Setting in Cement Mortar 1:4, complete all as specified and as directed.

M&L Brick Work with Sub-Class ‘B’ Bricks (Old Size Bricks), Straight or Curved on Plan exc. 6.0 Metre mean Radius, built in Cement Mortar 1:6, complete all as specified and as directed.

M&L Brick Work Half Brick thick with Sub-Class ‘B’ Bricks (Old Size Bricks), Straight or Curved on Plan to any Radius, built in Cement Mortar 1:4, complete all as specified and as directed.

M&L Cement Concrete 1:2:4 (12.5mm graded stone aggregate) 40mm thick in Damp Proof Course to Horizontal or Vertical Surfaces including Use & Waste of Formwork and Applying evenly a coat of Blown type Bitumen @ 1.50 KG/SQM and blinding with Clean Dry Sand @ 0.05 CUM/SQM, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) in Scantling, Cleanswan, Timber fixed (Unframed work), fixing with Nails, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Fillets in Wall Panelling, Plain on One Side, Square, Rectangular or Triangular in Section, exc. 13 Sq Cm but not exc. 25 Sq Cm, fixed with Nails, complete all as specified and as directed.

M&L Soft Wood Beading 30mm Width, Decorative type in Wall Panelling, fixed with Screws on Wall Panellig, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Panelled Shutter 35mm thick (any number Panels) Plain, Framed with Lock Rails, having Panels of 12mm thick Veneered Particle Board medium density, Wood Particle Board with commercial Face Veneers and fitted to Chowkat, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Glazed and Skeleton Shutter 35mm thick, Divided into Squares, with Plain, Chamfered or Rounded, mitred and rebated Sash Bars to receive Gauge/Glass, any numbers, Sizes of Members of Shutter as specified in SSR Part-I, Section 8, Clause 8.24(a) and fitted to Chowkat, complete all as specified and as directed.

S&F Factory made Solid PVC Door Frame of Size 50x47mm made out of 5.0mm thick Plain Colour (Ivory Shade) PVC Sheet reinforced with Mild Steel Square Tube and fixing in opening as per Specification and Drawing of MES Schedule Part-II, complete all as specified and as directed.

M&L Factory Made Solid Panel PVC Door Shutter 30mm thick (Style) Plain colour (Ivory shade) consisting of Frame made out of Mild Steel Tubes for Top and Bottom Rails, Mild Steel Frame shall be covered with heat moulded wood grain PVC ‘C’ Channel having a PVC Sheet Strip of 20mm width stuck inside with Solvent Cement for Stiles and wood grain PVC Sheets for Top Rail, Lock Rail & Bottom Rail on either side and as gap insert for Top Rail & Bottom Rail, Panelling of wood grain PVC Sheet to be fitted in the Mild Steel Frame welded/ sealed to the Stiles and Rails with suitable 5mm thick x 15mm wide PVC Sheet beading used inside Stiles and Rails and decorative PVC Beading of 10mm x 10mm (90º) and jointed together with Solvent Cement and fixing in the Frame at Site, complete all as specified and as directed.

S&F Steel Windows with Side Hung Shutters including Projecting type Hinges with Steel Handle and Steel Peg Stay, complete with Glazing Bars, dovetailed or welded, complete all as specified and as directed.

S&F Steel Windows with Side Hung Shutters including Projecting type Hinges with Steel Handle and Steel Peg Stay, complete without Glazing Bars, dovetailed or welded, complete all as specified and as directed.

S&F Steel Windows with Top Hung Shutters including Hinges, Steel Peg Stay, complete all as specified and as directed.

S&F Aluminium anodised Barrel Tower Bolt of Size 150mm long (as approved), Extruded Section, complete all as specified and as directed.

S&F Aluminium alloy, anodised, Sliding Door Bolt 250mm long (as approved) with Hasp, Staple (Bolt type) and Fixing Clips of Sheet, Cast or Extruded Sections and Fixing Bolts and Sliding Bolts of Extruded Sections or Cast-Aluminium alloy and fixed, complete all as specified and as directed.

S&F Stainless Steel Butt Hinge of Size 75mm (as approved), complete all as specified and as directed.

S&F Stainless Steel Butt Hinge of Size 100mm (as approved), complete all as specified and as directed.

S&F Aluminium Handle of Size 150mm (as approved), anodised, Cast type, complete all as specified and as directed.

S&F Floor Door Stopper with Overall length of Cover Plate 150mm of Aluminium Alloy Body and Tongue, anodised, with Hard Drawn Steel Spring, fixed in Floor, complete all as specified and as directed.

S&F Mild Steel 300mm, Ordinary Rat Tail Rod Pattern Springs including Roller and Roller Plate, complete all as specified and as directed.

S&F Stainless Steel Wire Cloth 0.36mm nominal dia of Wire and average width of aperture 1.40mm and fixed with Stainless Steel Wire Staples, complete all as specified and as directed.

S&F Sheet Glass 3.0mm thick, Plain, Ordinary quality in Square not exc. 0.50 Sqm in Each Pane and Glazing with Oil Putty, complete all as specified and as directed.

S&F Figured Sheet Glass 4.0mm thick, Pin Headed type in Square not exc. 0.50 Sqm in Each Pane and Glazing with Oil Putty, complete all as specified and as directed.

M&L Stainless Steel Curtain/ Drapory Rod having 24mm Outer dia with Wall thickness 1.00mm (minimum) including Brackets, Side Holders and Rings, etc. and Fixed-in-repairs, complete all as specified and as directed.

M&L TMT Bars 10mm dia and Over, cut to length, bent to shape required including cranking, bending spirally for hooping for Columns, hooking Ends and binding with and including Mild Steel Wire (annealed) not less than 0.9mm dia, complete all as specified and as directed.

M&L TMT Bars 8.0mm dia, cut to length, bent to shape required including cranking, bending spirally for hooping for Columns, hooking Ends and binding with and including Mild Steel Wire (annealed) not less than 0.9mm dia, complete all as specified and as directed.

M&L TMT Bars 8.0mm dia in Stirrups, Spacers and Binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including Mild Steel Wire (annealed) not less than 0.9mm dia, complete all as specified and as directed.

M&L Rolled Mild Steel Framed Work as in Doors or Gates of Angle or Other Section with Gusset Plates, Rails, Braces, etc., drilled for fixing of Steel Sheeting or Other Covering. Doors, etc. to be prepared for hanging or sliding with and including either Hooks and Hinges or Steel Hanging Door Fittings (exclusive of Steel Sheeting or Other Covering, Running Rails, etc) and hanging; also fastening and fixing, conforming to Fe-410-W (Gde E-250), Quality A, complete all as specified and as directed.

M&L Mild Steel Hand Rails, Half Round or Other Stock Section or Core for Wooden Hand Rail Straight portion, drilled and countersunk for Balusters Running Bars, for Doors, Balusters, Nosing to Steps including embeding in Concrete and screwing, etc. Wind Ties for Roof including securing Bolts; Posts and Struts in Fencing including cutting Tops to shape as directed, drilling holes, notching for Wire, etc.; Flat Iron Fillets (for securing Wire Mesh etc.) including all necessary drilling, bolting or riveting, etc., and Similar Work, conforming to Fe-290, Gde E-165, complete all as specified and as directed.

M&L Rolled Mild Steel Sections in Joist, Channel, Angle, or Tee Sections in Vertical Post, conform to Fe-410-W (Gde E-250) Quality 'B', fixed independently, without Connecting Plates, etc. (cut to ordinary lengths i.e. within 20mm of the Length indicated), complete all as specified and as directed.

M&L Rolled Mild Steel Sections in Main and Cross Beams, Hip & Jack Rafters, Purlins where connected to Common Rafters, Running Rails and Guides for Sliding Doors, conforming to Fe-410-W (Gde E-250), Quality 'A', fixed with Angle Cleats or Other Connecting Plates, complete all as specified and as directed.

M&L Mild Steel Tublar Trusses, Rafter, Purlins, etc. including Special Shaped Washers, etc. complete using ERW or Induction Butt welded Tubes, confirming to IS:1161-1979, Grade St-240, complete all as specified and as directed.

M&L Plates (Plain or Chequered) Channels, Square cut or Notched (Ordinary and Counter Sunk) forming Holes, without any Aattachment, conforming to Gde Fe-410-W (Gde E-250) Quality 'B', complete all as specified and as directed.

M&L Mild Steel Screw Bolts (Machine made) of any description (Dia of Neck and Length of Bolt as ordered/ as per Site requirment), with Hexagonal or Square Heads at One End and screwed the Other End, or screwed Both Ends, Each screwed End to be fitted with Washers and One Hexagonal or Square Nut, complete all as specified and as directed.

S&F Pre-painted Galvalume Aluminum Zinc Coating GI based Corrugated Steel Sheet 0.50mm thick Coloured, having Tensile Strength of 550 Mpa in Roof Covering, Cladding to Walls, fixed with Aluminum Self Tapping Screws and Aluminum Washers of suitable Size, complete all as specified and as directed.

M&L Re-fixing only Pre-painted Galvalume Corrugated Steel Sheets (Serviceable Pre-painted Galvalume Corrugated Steel Sheet obtained from BOQ Item No. 1.008 here-in-before) in Roof Covering, Cladding to Walls, fixed with Aluminum Self Tapping Screws and Aluminum Washers of suitable Size, complete all as specified and as directed.

S&F Pre-painted Galvalume Aluminum Zinc Coating GI based Plain Steel Sheet 0.50mm thick Coloured, having Tensile Strength of 550 Mpa in Ridges/ Roof Covering, Cladding to Walls, fixed with Aluminum Self Tapping Screws and Aluminum Washers of suitable Size, complete all as specified and as directed.

M&L Exposed Suspended False Ceiling System with GI Powder Coated Snap Grid/ Frame Work of size 605x605mm, all as per Specification and Drawing of MES Schedule (except Hangers), complete all as specified and as directed.

S&F Hangers 4.0mm dia GI (upto 1200mm length) for adjusting Level, fixed to Roof Slabs by means of Ceilling Cleats made out of GI Flat 40x3.0mm in size, 60mm long and Expansion Hold Fasteners 12.5mm dia, 40mm long, complete all as specified and as directed.

S&F HSPC Non-Asbestos Fibre Cement Building Boards 4.0mm thick, Pre-primed, Self Embossed, Textured Designer Boards, Water Resistant, Termite Resistant, Fire Resistant for insulation, fixed or laid/ inserted to GI/ Aluminum Snap Grid Frame Work with Screws, complete all as specified and as directed.

S&F Plywood Boards 6.0mm thick, Grade BWR, Type BB, fixed to Timber Frame Work with Nails to Timber Frame Work in Walls, complete all as specified and as directed.

M&L Prelaminate Particle Boards 12mm thick, Interior Grade, Prelaminated on Both Sides with Decorative Choice Lamination and Other Side Balancing White Lamination and fixed with Screws to Timber Frame Work, complete all as specified and as directed.

M&L Cement Concrete 1:4:8 (40mm graded stone aggregate) 75mm thick in Sub-base to Floors, etc., complete all as specified and as directed.

M&L Cement Concrete 1:2:4 (20mm graded stone aggregate) 40mm thick in Flooring, etc., laid in Alternate Panels, finished Concrete Surfaces Even and Smooth with using Extra Cement, complete all as specified and as directed.

M&L Glass Dividing Strip 38mm Wide and 3.0mm thick and inserted in Position, conform to Design, complete all as specified and as directed.

M&L Cement Concrete 1:2:4 (12.5mm graded stone aggregate) 25mm thick as Base Course for laying Tiles on Flooring, etc., finished Concrete Surfaces Fair and Even, complete all as specified and as directed.

M&L Rubberised Bituminious Mastic Flooring 40mm thick with PVC Strip and Hardner for Gas Godown suitable for Loading and Unloading of Gas Cylinders, complete all as specified and directed

M&L Non-skid Ceramic Coloured/Designer Joint Free Tiles (1st quality and/or as approved) 7.0mm to 8.0mm thick (Square/ Rectangular), Area of Each Tile exc. 0.11 Sqm but not exc. 0.18 Sqm in Floors, Jointed in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, laid over and including Cement Screed Bed 15mm thick in Cement Mortar 1:6, complete all as specified and as directed. NOTE : Cost of Cement Screed Bed will deem to include in the Quoted Unit Rate.

M&L Non-skid Ceramic Coloured/Designer Joint Free Tiles (1st quality and/or as approved) 7.0mm to 8.0mm thick (Square/ Rectangular), Area of Each Tile exc. 0.11 Sqm but not exc. 0.18 Sqm in Vertical Surfaces i.e. Dado, Skirting, etc., Set in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, fixing over and including Cement Screed Bed 10mm thick in Cement Mortar 1:4, complete all as specified and as directed. NOTE : Cost of Cement Screed Bed will deem to include in the Quoted Unit Rate.

M&L Non-skid Ceramic Coloured/Designer Joint Free Tiles (1st quality and/or as approved) 7.0mm to 8.0mm thick (Square/ Rectangular), Area of Each Tile exc. 0.18 Sqm but not exc. 0.38 Sqm in Floors, Jointed in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, laid over and including Cement Screed Bed 15mm thick in Cement Mortar 1:6, complete all as specified and as directed. NOTE : Cost of Cement Screed Bed will deem to include in the Quoted Unit Rate.

M&L Non-skid Ceramic Coloured/Designer Joint Free Tiles (1st quality and/or as approved) 7.0mm to 8.0mm thick (Square/ Rectangular), Area of Each Tile exc. 0.18 Sqm but not exc. 0.38 Sqm in Vertical Surfaces i.e. Dado, Skirting, etc., Set in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, fixing over and including Cement Screed Bed 10mm thick in Cement Mortar 1:4, complete all as specified and as directed. NOTE : Cost of Cement Screed Bed will deem to include in the Quoted Unit Rate.

M&L Glazed Ceramic Coloured Tiles 350x250x7.0mm or 450x350x7.0mm thick (1st quality and/or as approved) in Vertical Surfaces i.e. Dado, Skirting, etc., Set in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, fixing over and including Cement Screed Bed 10mm thick in Cement Mortar 1:4, complete all as specified and as directed. NOTE : Cost of Cement Screed Bed will deem to include in the Quoted Unit Rate.

M&L Cement Concrete 1:4:8 (40mm graded stone aggregate) 100mm thick in Sub-base to Floors, etc., complete all as specified and as directed.

M&L Machine Pressed Pre-cast Concrete Interlocking Paver Block 60mm thick in M-35 Grade, confirming to IS:15658-2006, in any Shape and Size (as ordered) with Grey Cement and Coloured Pigment, laid Dry over Sand Cushioning, complete all as specified and as directed. NOTE : Sand Cushioning will be Measured and Paid for separately under appro-priate Item.

M&L Rubber Moulded Coloured Glossy Finished Machine Pressed Pre-cast Concrete Interlocking Paver Block 60mm thick in M-35 Grade, confirming to IS:15658-2006, in any Shape and Size (as ordered) with Grey Cement and Coloured Pigment, laid Dry over Sand Cushioning, complete all as specified and as directed. NOTE : Sand Cushioning will be Measured and Paid for separately under appro-priate Item.

M&L Sand Cushioning with Clean and Dry Sand, Filling in and Under Paver Blocks in layer of exc. 50mm thick including Watering and Consolidation, complete all as specified and as directed.

M&L Cement Concrete 1:3:6 (40mm graded stone aggregate) 75mm thick in Plinth Protection, etc., Laid in Alternate Panels, finished Concrete Surfaces Even and Smoooth without Using Extra Cement, complete all as specified and as directed.

M&L Joint Filling on Plinth Protection with 1 Part of Bitumen and 3 Parts of Sand, complete all as specified and as directed.

M&L Rendering 10mm thick in Cement Mortar 1:6 on Brick/ PCC Blocks or Concrete Works, finished Plastered Surfaces Even and Smooth without using Extra Cement, complete all as specified and as directed.

M&L Rendering 15mm thick on Bricks/Pre-cast Blocks or Concrete Works consisting in 2 layers, Backing/Under layer of 10mm thick in Cement Mortar 1:4 and Float/ Top layer 5.0mm thick in Cement Mortar 1:4 including mixing WPC to Float/ Top layer, finished Fair and Even, complete all as specified and as directed. NOTE : Water Proofing Compound (WPC) will be Measured and Paid separately under appropriate Item.

Supply only Water Proofing Compound (as approved), conforming to IS:2645-2003, complete all as specified and as directed.

M&L Preparing New Plastered Surfaces of Walls and applying Three Coats of White Wash, complete all as specified and as directed.

M&L Preparing New Plastered Surfaces of Walls and applying Two Coats of Distemper Oil Emulsion (of approved Tint) over a Coat of Chalk Whitening (Priming Coat), complete all as specified and as directed.

M&L Preparing Old Distempered Surfaces of Walls by Washing, Rubbing down and Stopping of Surfaces and applying One Coat of Distemper Oil Emulsion (of approved Tint), complete all as specified and as directed.

M&L Preparing Newly Plastered Surfaces of Walls and applying Two Coats of Cement Based Paint (of approved Tint) over a coat of Alkali Resistant Priming Paint, complete all as specified and as directed.

M&L Preparing Old Decorated/Treated Plastered Surfaces of Walls and applying One Coat of Cement Base Paint (of approved Tint), complete all as specified and as directed.

M&L Preparing New Wooden Surfaces of any description, over 10 Cm in Width or Girth and applying Two Coats of Synthetic Enamel Paint (1st quality/ grade Paint of approved Tint) over a Coat of Pink Primer, complete all as specified and as directed.

M&L Preparing Old Painted Wooden Surfaces of any description, over 10 Cm in Width or Girth and applying One Coat of Synthetic Enamel Paint (1st quality Paint of approved Tint), complete all as specified and as directed.

M&L Preparing Steel and Iron Surfaces of any descriptions, over exc. 10 Cm in Width or Girth and applying Two Coats of Synthetic Enamel Paint (1st quality/ grade Paint of approved Tint) over a Coat of Red Oxide Zinc Chrome Primer, complete all as specified and as directed.

M&L Preparing Steel Surfaces of Sheets on Roofing, Walls, etc. of any descriptions, over exc. 10 Cm in Width or Girth and applying Two Coats of Synthetic Enamel Paint (1st quality/ grade Paint of approved Tint) over a Coat of Red Oxide Zinc Chrome Primer, complete all as specified and as directed.

M&L Preparing Old Treated Steel and Iron Surfaces of any descriptions, exc. 10 Cm in Width or Girth and Applying One Coat of Synthetic Enamel Paint (1st quality/ grade Paint of approved Tint), complete all as specified and as directed.

M&L Preparing Steel and Iron Surfaces of Sheets on Roofing, Walls, etc., over 10 Cm in Width or Girth and applying a Coat of Synthetic Enamel Paint (1st quality/ grade Paint of approved Tint), complete all as specified and as directed.

M&L Preparing New or Previously Treated Surface of Wood and Wood based Materials of any description (Hidden Surfaces) and girth and treated with Two Coats of Creosote Oil, complete all as specified and as directed.

M&L Cleaning and Preparing Surface of Wood and Wood based Materials of any description and Girth and Treated with French Polishing on New Works with Two or More Coats including a coat of Wood Filler, complete all as specified and as directed

S&F Galvanised Steel Tubing 15mm bore (dia), medium grade, conforming to IS-1239 with all Fittings, fixed to Walls, Ceiling or laid in Floors, complete all as specified and as directed.

S&F Galvanised Steel Tubing 20mm bore (dia), medium grade, conforming to IS-1239 with all Fittings, fixed to Walls, Ceiling or laid in Floors, complete all as specified and as directed.

S&F Bib Tap 15mm bore (dia) Cast Copper alloy, Chromium Plated, Fancy type, with Crutch or Butter-fly Handle, screwed down, screwed for Iron Pipe or for Brass Ferrule, complete all as specified and as directed.

S&F Pillar Tap 15mm bore (dia), Cast Copper alloy, Chromium Plated, Swan Neck with Capstan Heads, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with Long Screwed Shanks and Fly-nuts, screwed for Iron Pipe, complete all as specified and as directed.

S&F Stop Valve 15mm bore (dia), Cast Copper alloy, Chromium Plated, Fancy type, screwed down, high pressure, with Crutch or Butter-fly handle, screwed both Ends for Iron Pipe or for Unions, complete all as specified and as directed.

S&F Gun Metal Globe/Gate Valve 20mm bore (dia) with Iron Wheel Head, screwed both Ends for Iron Pipe, complete all as specified and as directed.

M&L Rotational Moulded Polyethene Water Storage Tank 500 Litre Capacity, Cylindrical, Vertical with Closed Top, 3 layered, conforming to IS:12701-1996, hoisted and fixed in Position all as specified in MES Schedule and Providing Water Pipe Line Connections, complete all as specified and as directed.

S&F PTMT Ball Valve 20mm bore (dia), having weight not less than 210 Gram, high pressure with Epoxy Coated Aluminium Rod and Hgh Density Plastic Ball, screwed for Iron Pipe, complete all as specified and as directed.

M&L Vitreous China White Squatting Pan of Size 580x440mm, Orissa Pattern with Integral Foot Rests, PVC (SWR) ‘P’ or ‘S’ Trap, providing Joints between Flush Pipe and Socket of WC Pan, Cones, India Rubber (nozzles of WC Pan) incluiding provision of Lime Concrete Bedding and Making Good to distrubed/ Floor Surfaces, complete all as specified and as directed.

S&F Vitreous China White Wash Down Water Closet Pan (Pedestal Pattern) with PVC (SWR) ‘P’ or ‘S’ Trap and Fixing Bolts and Making Good to Floor/ Distrubed Surfaces in Cement Mortar 1:3, complete all as specified and as directed.

S&F White Plastic Water Closet Seat and Cover for Water Closet Pan (Pedestal Pattern), Closed Pattern with Flat bottom and Cover and Mild Steel Chromium plated or Aluminised Hinging Device, complete all as specified and as directed.

S&F Jet System (as approved), Chromium Plated suitable for Wash Down Water Closet Pan (Pedestal Pattern), complete all as specified and as directed.

S&F PVC Flushing Cistern 10 Litre capacity White, Low Level, Valveless, Syphonic Action type with Inlet, Ball Valve, Float & Handle, and PVC Flush Pipe 32mm bore (dia), a Pair of Cast Iron Brackets Erecting Stand duly painted including cutting and pinning in Ends, Making Good Disturbed Surfaces in Cement Mortar 1:3, complete all as specified and as directed.

S&F Vitreous China White Urinal 465x355x265mm in Size, Flat back with and including Grating & Union for Discharge Pipe, PTMT Waste Coupling 32mm bore (dia) of Full Threaded, PTMT Waste Pipe 32mm bore (dia), PTMT Urinal Spreader suitable for fixing with 15mm bore (dia) GI Pipe (but excluding Flushing Cistern, Flush Pipe and Waste Pipe) including Providing and Fixing Plugs, Bedding Urinals against Wall in Cement Mortar 1:2, securing Urinal to Plug with and including 60mm long Brass Chromium plated Screws, Pointing around Urinal back in Cement Mortar 1:3, complete all as specified and as directed.

S&F Vitreous China White Wash Hand Basin 550x400mm in Size, Oval Shaped with Brass Chromium Plated Waste Coupling/Fitting 32mm bore (dia) and PVC Waste Pipe 32mm bore (dia) including a Pair of Cast Iron Brackets Brackets Erecting Stand (300mm long) duly Painted, Cutting and Pinning in Ends and Making Good Disturbed Surfaces in Cement Mortar 1:3, complete all as specified and as directed.

S&F Vitreous China White Wash Hand Basin 550x400mm in Size, Flat Back with Brass Chromium Plated Waste Coupling/Fitting 32mm bore (dia) and PVC Waste Pipe 32mm bore (dia) including a Pair of Cast Iron Brackets Brackets Erecting Stand (300mm long) duly Painted, Cutting and Pinning in Ends and Making Good Disturbed Surfaces in Cement Mortar 1:3, complete all as specified and as directed.

S&F PVC Connection Pipe 15mm in Size and 450mm in length with PTMT Nuts suitable for Flushing Cistern, Wash Hand Basin, etc., complete all as specified and as directed.

S&F Brass Chromium plated Shower Rose 125mm Size, with or without Swivel Joints, including fixing to GI/ Steel Pipe 15mm bore (dia) or Union, complete all as specified and as directed.

S&F Soap Dish not less than 150mm in Size, Chromium plated, Fancy type (as approved), fixed on Wall with Wooden/ PVC Cleats and Brass Chromoum Plated Screws, complete all as specified and as directed.

S&F Tubular Towel Rail 20mm dia, Brass Chromium Plated, D-type, 60 Cm long between Flanges with Bracket (One Pair), fixed on Wall with Wooden/ PVC Cleats and Brass Chromoum Plated Screws, complete all as specified and as directed.

S&F PVC (SWR) 75mm bore (dia) Floor Trap having Diameter of Outlet 75mm, Plain with Grating including Jointing with Solvent Cement, complete all as specified and as directed.

S&F PVC (SWR) Pipe 75mm bore (dia), Single Socketed, in any length with Rubber Ring Joints, laid in Trenches or in Floors, etc., complete all as specified and as directed.

S&F PVC (SWR) Bend 75mm bore (dia), any Radius, etc. and Jointing with Solvent Cement, complete all as specified and as directed.

S&F PVC (SWR) Pipe 110mm bore (dia), Single Socketed, in any length with Rubber Ring Joints, laid in Trenches or in Floors, etc., complete all as specified and as directed.

S&F PVC (SWR) Bend 110mm bore (dia), any Radius, etc. and Jointing with Solvent Cement, complete all as specified and as directed.

S&F PVC (SWR) Bend 110mm bore (dia), any Radius, etc. with Acess Door and Jointing with Solvent Cement, complete all as specified and as directed.

S&F PVC (SWR) 160mm bore (dia) Pipe, Single Socketed, in any length with Rubber Ring Joints, laid in Trenches and Tested after laid, complete all as specified and as directed. NOTE : Necessary Earth works will be Measured and Paid separately under appropriate Items.

M&L Cement Concrete 1:4:8 (40mm graded stone aggregate) in Concrete Bed to Drain Pipes of 160mm bore (dia) including Packing Under and Haunching against the Sides of Pipes after they are laid and tested; complete all as specified and as directed. NOTE : Necessary Earth works will be Measured and Paid separately under appropriate Items.

M&L Cutting into existing Manholes for Connecting PVC (SWR) Drain Pipe 160mm bore (dia), Making Good to Pipe and Rendering, Cutting out existing Benching for and forming Branch Channel (½ Round or ¾ Section) in Cement Concrete 1:2:4 (20mm graded stone aggregate), Smooth Finished and Reforming Benching as required, complete all as specified and as directed.

E/M SERVICES/WORKS

M&L Taking down carefully Copper Point Wiring (Light, Fan, Socket or Power) complete from in any Position including Fixture and Fittings such as Switches, Ceiling Roses, Pendants, Regulators, Sockets but excluding Light Fittings of any description, Making Good Disturbed Surfaces of Walls/ Ceillings, etc. in Cement Mortar 1:3 including Providing Surface Treatment (White/ Colour Washing, Distempering, Painting, etc.) wherever required to match the Existing Finishes, complete all as specified and as directed.

M&L Taking down Unserviceable Sub-main Wiring from PVC Conduit/ PVC Casing Capping of any description, Making Good disturbed surfaces of Walls/ Ceillings, etc. in Cement Mortar 1:3 including providing Surface Treatment (White/Colour Washing, Distempering, Painting, etc.) wherever required to match the Existing Finishes, complete all as specified and as directed.

M&L Taking down/out Unserviceable Service Connection of any description from any Situations, complete all as specified and as directed.

M&L Point Wiring with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLSH multi-stranded single core Copper Conductor Cable with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLSH multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuity Wire, drawn in and including PVC Casing Capping (ISI Marked) of suitable Size (approx 25/32/40mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc. complete with PVC Board of suitable Size for accommoda-ting Switches, Sockets, Regulators, etc. Earth Continuity Wire connected to Common Earth dolly for ONE LIGHT/ FAN/ BELL POINT controlled by One 1-way Switch 6 Amp, complete all as specified and as directed.

M&L Point Wiring with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLSH multi-stranded single core Copper Conductor Cable with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLSH multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuity Wire for ONE 3/5 PIN SOCKET 6 AMP POINT on SAME BOARD, complete all as specified and as directed.

M&L Point Wiring with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLSH multi-stranded single core Copper Conductor Cable with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLSH multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuity Wire, drawn in and including PVC Casing Capping (ISI Marked) of suitable Size (approx 25/32mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc. complete with PVC Board of suitable Size for accommoda-ting Switches, Sockets, Regulators, etc. Earth Continuity Wire connected to Common Earth dolly for ONE 3/5 PIN SOCKET OUTLET 6 AMP POINT on INDEPENDENT BOARD, complete all as specified and as directed.

M&L Point Wiring with 2.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLSH multi-stranded single core Copper Conductor Cable with 2.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLSH multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuity Wire, drawn in and including PVC Casing Capping (ISI Marked) of suitable Size (approx 25/32mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc. complete with PVC Board of suitable Size for accommoda-ting Switches, Sockets, Regulators, etc. Earth Continuity Wire connected to Common Earth dolly for ONE 3/5 PIN SOCKET OUTLET 6/16 AMP POINT on INDEPENDENT BOARD, complete all as specified and as directed.

M&L Sub-main Wiring with 2-Run of 4.0 Sqmm (nominal area) 1100 Volt grade PVC insulated, unsheathed, multi-stranded, single core FRLSH Copper Conductor Cable and 1-Run of 2.5 Sqmm (nominal area) 1100 Volt grade PVC insulated, unsheathed, multi-stranded, single core FRLSH Copper Conductor Cable (Green Colour) as Earth Continuty Conductor drawn through and including PVC Casing Capping (ISI Marked) of suitable Size (approx 25/32mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc., complete all as specified and as directed. NOTE :- (a) Cost of 3-Run of Cable & 1-Run of PVC Casing Capping will deem to be include in the Quoted Unit Rate and the same will be Mesured as ONE UNIT. (b) Sub-main Wiring will be measured PVC Casing Capping only. Wires required/ as ordered for looping, etc. will deem to be include in the Quoted Unit Rate.

S&F PVC Rectangular Board/Block of Size 250x200x50mm Deep, Closed Recessed with 3.0mm thick Plastic Laminated Sheet Cover for mounting Swiches, Sockets, Fan Regulators, etc. including Taking down/ out Unserviceable Board/ Block (02 No.) of any description, complete all as specified and as directed.

S&F PVC Rectangular Board/Block of Size 350x300x50mm Deep, Closed Recessed with 3.0mm thick Plastic Laminated Sheet Cover for mounting Swiches, Sockets, Fan Regulators, etc. including Taking down/ out Unserviceable Board/ Block (02 No.) of any description, complete all as specified and as directed.

S&F Switch Piano 6 Amp, Single Pole, Flush type, 1-way, 230 Volt AC and connecting up, complete all as specified and as directed. NOTE : Old Unserviceable Switch Piano 90 No. derived from Taking down of Point Wiring will be catered under Schedule of Credit.

S&F Socket Outlet 6 Amp, 5 Pin, Flush type, Multipurpose, 230 Volt AC, suitable for 6 Amp, 2/3 Pin Plug Top and connecting up, complete all as specified and as directed NOTE : Old Unserviceable Socket Outlet 22 No. derived from Taking down of Point Wiring will be catered under Schedule of Credit.

S&F Switch Socket Combination 6/16 Amp, (3 & 3 Pin), 2-in-1, Multipurpose, Flush type, 230 Volt AC and connecting up, complete all as specified and as directed.

S&F Switch Socket Combination 6 Amp, 3/5 Pin & 16 Amp, 3/5 Pin, Multi-plug, Flush type, 230 Volt AC and connecting up, complete all as specified and as directed. NOTE : Old Unserviceable Switch Socket Combination 10 No. derived from Taking down of Point Wiring will be catered under Schedule of Credit.

S&F Lamp/ Angle Holder PVC/ Polycarbonate type with Back Plate suitable for Batten Fitting and connecting up, complete all as specified and as directed. NOTE : Old Unserviceable Lamp/ Angle Holder 06 No. derived from Taking down of Point Wiring will be catered under Schedule of Credit.

S&F Ceiling Rose 65x50mm, 3 Terminals, Surface Bakelite suitable for 230 Volt AC and connecting up, complete all as specified and as directed. NOTE : Old Unserviceable Ceiling Rose 68 No. derived from Taking down of Point Wiring will be catered under Schedule of Credit.

S&F Ceiling Fan Regulator, Electronic, Stepped type, 230 Volt AC including necessary Connection and connecting up, complete all as specified and as directed. NOTE : Old Unserviceable Fan Regulator 08 No. derived from Taking down of Point Wiring will be catered under Schedule of Credit.

S&F LED Bulk Head Luminaire 1x10 Watt with High brightness LEDs, Surface mounted, Enviroment Friendly, Ultra Modern, Energy Saving and connecting up with and including suitable Size Twisted Flexible Copper Conductor Cable including Taking down Unserviceable Light Fitting (08 No.) of any description from any Situation, complete all as specified and as directed. NOTE : Old Unserviceable Light Fitting 08 No. against Taking down of Point Wiring will be catered under Schedule of Credit.

S&F LED Tube Light Fitting 1x10 Watt with 10 Watt LED Tube, Wall or Ceiling mounted type with all Accessories, Pre-wired, fixing on and including providing PVC Box (2 No) and connecting up with and including Twisted Flexible Copper Conductor Cable of Size 40/0.0076 of suitable Length including Taking down Unserviceable Light Fitting (05 No.) of any description from any Situation, complete all as specified and as directed. NOTE : Old Unserviceable Light Fitting 05 No. against Taking down of Point Wiring will be catered under Schedule of Credit.

S&F LED Tube Light Fitting 1x20 Watt with 20 Watt LED Tube, Wall or Ceiling mounted type with all Accessories, Pre-wired, fixing on and including providing PVC Box (2 No) and connecting up with and including Twisted Flexible Copper Conductor Cable of Size 40/0.0076 of suitable Length including Taking down Unserviceable Light Fitting (37 No.) of any description from any Situation, complete all as specified and as directed. NOTE : Old Unserviceable Light Fitting 37 No. against Taking down of Point Wiring will be catered under Schedule of Credit.

S&F LED T-5 Tube Light Fitting 1x20 Watt, 4 Feet long with LED 20 Watt Integrated Batten and connecting up with and including suitable Size and Length Twisted Flexible Copper Conductor Cable, complete all as specified and as directed.

S&F LED PANEL (2'x2') Light Fitting 34 Watt with High Brightness SMD LEDs as Light Source, Recess/Ceiling mounted, Ultra Modern, Enviromentaly Friendly, New Generation with Electronic Driver 34 Watt and all Accessories, Pre-wired and connecting up with including suitable Size and Length Twisted Flexible Copper Conductor Cable, 3 Core including Taking down/ out Unserviceable Light Fitting (04 No.) of any description, complete all as specified and as directed. NOTE : Old Unserviceable Light Fitting 04 No. against Taking down of Point Wiring will be catered under Schedule of Credit.

M&L Taking down Ceiling Fan, Exhaust Fan of any Make and Sweep from any Height after disconnecting Electric Connection and Keep in Safe Custody for Re-fixing / Re-hanging, complete all as specified and as directed.

M&L Transporting Ceiling Fan of any Make and Sweep from Site of Works to nearest Workshop, Opening Fan Cover for Taking out burnt Winding of any description, Cleaning Slot, Rewinding Fan Motor with Super Enamalled Copper insulated Wire of suitable Gauge and Weight (as per existing), Providing necessary Insulation Materials, Varnishing, Heating, Reassembling & Testing for Smooth Functioning after Rewinding, Removing the Repaired Fan to Site of Work after Rewinding, complete all as specified and as directed.

M&L Preparing Old Painted Surfaces of Ceiling Fan of any Make and Sweep/ Size including Cleaning, Washing, Rubbing and Filling Cavities with Filler, applying One Coat of Synthetic Enamelled Paint (as approved) with Spray Painting Machine and Writing MES No. with Black Paint, complete all as specified and as directed.

M&L Mild Steel Flat Iron 40x5mm in Fan Hook, Cut to Length, bent to Shape as ordered, drilling holes for Bolts including Mild Steel Bolts, Nuts and Washers, conform to Fe-290 Gde-E-165 including Taking down Unserviceable Fan Hook (08 No.) of any description from any Situation, complete all as specified and as directed.

M&L Re-hanging/Refixing only Ceiling Fan, Exhaust Fan (obtained from BOQ Item No. 2.023 here-in-before) and connecting with and including suitable Size Twisted Flexible Copper Conductor Cable from Ceiling Rose to Connector of the Fan, complete all as specified and as directed.

Supply & Hanging BLDC Ceiling Fan 1200mm Sweep, 26 Watt with Squirrel Cage Induction Motor, having 3 Blades, Holding Down Rod and Accessories, 230 Volt, providing Electric Connection from Ceiling Rose to Ceiling Fan with and including Twisted Flexible Copper Conductor Cable of suitable Size and Length, 3 Core, complete all as specified and as directed.

S&F Metallic Body Exhaust Fan 300mm Sweep with Louver, Single Phase, 230/240 Volt complete with Fixing Arrangement using Fastener and providing Electric Connection with and including suitable Size 3 Core Copper Conductor Cable from Ceiling Rose to Exhaust Fan, complete all as specified and as directed.

S&F MCB Single Pole 6 Amp to 32 Amp, 'C' Series, 50 Hz, 10 kA, 240 Volt and connecting up including Taking down/ out Unserviceable MCB (12 No.) of any description, complete all as specified and as directed. NOTE : Old Unserviceable MCB 12 No. obtained from Taking down/ out will be catered under Schedule of Credit.

S&F MCB Single Pole & Neutral 40 Amp, 'C' Series, 50 Hz, 10 kA, 240 Volt and connecting up including Taking down/ out Unserviceable MCB (04 No.) of any description, complete all as specified and as directed. NOTE : Old Unserviceable MCB 04 No. obtained from Taking down/ out will be catered under Schedule of Credit.

S&F Sheet Metal Enclosure for DB's when MCBs to be used 4-way, SPN, 240 Volt, Double Doors, Epoxy Based Powder coated suitable for mounting MCB DP/ SPN as Incomer and MCB SP as Out-goings with 200 Amps rated Bus-bar, Neutral Bar, Earth Bar, Connecting Cable Links, having IP-43 Protection and Connecting up including Taking down Unserviceable Sheet Metal Enclosure (02 No.) for DBs of any description, complete all as specified and as directed. NOTE : Old Unserviceable Sheet Metal Enclosure for DB's 02 No. obtained from Taking down/ out will be catered under Schedule of Credit.

S&F Sheet Metal Enclosure for DB's when MCBs to be used 8-way, SPN, 240 Volt, Double Doors, Epoxy Based Powder coated suitable for mounting MCB DP/ SPN as Incomer and MCB SP as Out-goings with 200 Amps rated Bus-bar, Neutral Bar, Earth Bar, Connecting Cable Links, having IP-43 Protection and Connecting up including Taking down Unserviceable Sheet Metal Enclosure (02 No.) for DBs of any description, complete all as specified and as directed. NOTE : Old Unserviceable Sheet Metal Enclosure for DB's 02 No. obtained from Taking down/ out will be catered under Schedule of Credit.

Supply and Laying or Fixing or Passing through Pipe, 1100 Volt grade Heavy duty Cable with PVC insulated Aluminium Stranded Conductor served with an Inner sheathing of PVC Tape armoured with Galvanised Steel Wire or Tape and Overall PVC sheathed 10 Sqmm Nominal Cross Section, 2 Core in Service Connection, complete all as specified and as directed.

M&L Earthing with Galvanised Earth Plate Electrode 600x600x6.0mm thick, buried directly in Ground vertically to a depth not less than 2.25 Metre below Ground Level with Top Edge of Earth Plate at depth not less than 1.50 Metre below normal Ground Level, connected to Galvanised Earth Lead Wire 4.0mm dia by means of Bolts, Nuts, Check, Nuts and Washers of Galvanised Iron or Steel and Earth Wire protected with and including GI Pipe 15mm bore (dia) light grade, connected to Test Point upto 7.50 Metre away from Earth Electrode situated, Earth Plate surrounded by a packed thickness of Char Coal or Coke Dust mixed with Common Salt in alternate layers of not exc.150mm thick, PCC Pit in Cement Concrete 1:3:6 (20mm graded stone aggregate) and Pre-cast RCC Cover Slab of Size 350x350x50mm in Cement Concrete 1:2:4 (20mm graded stone aggregate), reinforced with 10mm dia TMT Bars @ 100mm Centre to Centre in both ways, GI Wire Mesh, PGI Funnel with GI Watering Pipe 20mm bore (dia) Medium grade including necessary Excavation in Soft/ Loose Soil, Returning, Filling in and Removal of surplus Spoil upto a distance of 50.00 Metre and all as shown in Electrical Plate No. 3 of MES Schedule Part-I and Testing including Taking down/ out Unserviceable Earthing (03 Set) for DBs of any description, complete all as specified and as directed.

Excavating in Trenches, not exc. 1.50 Metre Wide and not exc. 1.50 Metre in Depth for Taking out/ up and/or laying of Water Pipe Line, Cable Line, etc., Forming surfaces to required Foundation/ Gradient and getting out in Soft/Loose Soil, complete all as specified and as directed.

Returning, Filling in including Spreading, Levelling, Watering, Well Ramming in Layers not exc. 25 Cm, Providing Heaps with Surplus Soil along the Route of the Water Pipe Line, Cable Line, etc., in Soft/Loose Soil, complete all as specified and as directed.

Supply & Laying LT Under Ground Cable 1100 Volt grade, XLPE insulated, PVC sheathed heavy duty, armoured with multi-stranded Aluminium Conductor all as per IS:7098 (Part-I)-1998, Cross-sectional Area 16 Sqmm, 2 Core, laid in Trenches, Ducts or through Pipes or fixing to Poles, etc. complete all as specified and as directed. NOTE : Necessary Earth Works, Sand Cushioning, Cable Protection Cover & Pipe, etc. will be Measured and Paid separately under relevent Items.

M&L Sand Cushioning (dry) in Trenches/Ducts for protection of UG Cables (below, above and around the UG Cable laid) of 23 Cm Spread thickness (8 Cm in depth before laying the Cable and 15 Cm in depth after laying the Cable) and consolidated (punned) upto 180mm thickness, complete all as specified and as directed. NOTE : For the purpose of Payment, Punned thickness of Sand Cushioning only will be Measured.

Supply & laying Sub-class ‘B’ Bricks of Size 230x115x75 mm, Kiln burnt, for Covering to UG Cable as Protection, laid Flat, Transversally Width Equal to the Length of the Cable, complete all as specified and as directed.

Supply, Installation & Commissioning LT Panel, Factory Made (CPRI Approved/ Tested Manufacturer), made out of CRCA 16 SWG Mild Steel Sheet, Powder coated, Outdoor type, Totally Enclosed, Weather Proof type, Double Doors, Front Opening Shutter with Proper Locking Arrangements, etc., mounted on Mild Steel Angle Iron Leg 40x40x5.0mm (4 No) not less than 500mm Height from Natural Ground Level duly Painted with Two Coats of Syenthic Enamel Paint over a coat of Red Oxide Zinc Chrome Primer, grouting Legs in Cement Concrete 1:2:4 (20mm graded stone aggre-gate) Block/ Plinth of appropriate Size including necessary Formworks, Earthworks, etc., Providng all Electric Connections and Testing, complete all as specified and as directed and Comprising with and to Accomodate the following:- (a) Copper Bus-bar of rating 100 Amp, 4 Strip, 450mm long - 01 Set (b) MCB 63 Amp TPN, 4 Pole, 25 kA, 415 Volt - 01 No. (c) MCB 63 Amp SPN, 10 kA, 230 Volt - 02 No.

Supply & laying Galvanised Steel Tubing 20mm bore (dia) medium grade, conform to IS-1239 with all Fittings, laid in Trenches, complete all as specified and as directed. NOTE : Necessary Earth Works will be Measured and Paid separately under relevent Items.

Supply & laying Galvanised Steel Tubing 25mm bore (dia) medium grade, conform to IS-1239 with all Fittings, laid in Trenches, complete all as specified and as directed. NOTE : Necessary Earth Works will be Measured and Paid separately under relevent Items.

Supply & laying Galvanised Steel Tubing 40mm bore (dia) medium grade, conform to IS-1239 with all Fittings, laid in Trenches, complete all as specified and as directed. NOTE : Necessary Earth Works will be Measured and Paid separately under relevent Items.

S&F Gun Metal Globe/Gate Valve 25mm bore (dia) with Iron Wheel Head, screwed both Ends for Iron Pipe, complete all as specified and as directed.

S&F Gun Metal Globe/Gate Valve 40mm bore (dia) with Iron Wheel Head, screwed both Ends for Iron Pipe, complete all as specified and as directed.

M&L Cutting Cast Iron or GI Pipes of any Size and reducing to required Length before laying and Existing Pipe Lines for Taking up Branch Connection and Insertion of Specials, complete all as specified and as directed. NOTE : Cost of all Necessary Materials i.e. Specials and Labours required at Site will deem to be include in the Quoted Unit Rate.

SHRI MANOJ KONWAR

M/s JK Jangid and Company

M/S Raju prasad

M/S Build Tech

M/s Shiva Technical Enterprise

M/S R & R D ENTERPRISES

M/S Abhi Traders

Prova Stores

M/S RK Trading

M/s United Builders