REPAIR TO BOUNDARY WALL, STEEL GATE, PERIMETER WALL, RCC JALIES, PLASTERING, STEEL GRILL WORK ON BOUDARY WALL AND CERTAIN B/R WORKS AT RAKSHA VIHAR COLONY UNDER GE (I) R and D KANPUR.

Amount

Demolition of brick work built in cement mortar as in foul position for manhole and drain etc and removing to a distance exceeding 50 metre but not exceeding 100 metre complete all as specified and directed.

M&L for Brickwork with sub class ‘B’ bricks, straight or curved on plan exc 6m mean radius built in cement mortar (1:4) Complete all as specified and directed.

Except bricks work with sub class 'B' bricks straight or curved on plan exc 6 m mean radius built in cm 1:4 complete all as specified and directed.

M&L for brick work with bricks old size brick, straight or curved on plan or radius in half brick thick built in cement mortar 1:4 complete all as specified and directed.

M & L rendering 15mm thick on wall in cement mortar 1:4 on fair faces of brick work or concrete surfaces & finished fair and even smooth without using extra cement complete all as specified and directed.

M&L for two coat of cement base paint over New surfaces including preparation of surface complete all as specified and directed.

Demolition of cement concrete in ground floor and paving not exc.15 cm thickness (below or above ground level) complete all as specified and directed.

M & L for 75mm thick PCC (1:3:6) type C-2 as in plinth protection & finishing the surface even & smooth without using extra cement complete all as specified & directed.

Providing cement concrete 1:2:4 type B-1 in roof kerbs or Coping on compound wall, mud stops, gola, rounded, flat or chamfered on edges,complete all as specified and directed.

M&L PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in foundation, filling, mass concrete complete all as specified and directed.

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) tank and removing the same from the premises complete all as specified and directed.

M&L for precast cement concrete type B-0 1:2:4 (12.5 mm graded aggregate) and set in Cement Mortar (1:4) as in louvres and jallies, 35mm thick (measured solid) including all mouldings, necessary formworks and reinforcement and dismantling existing RCC jallies in any description all as specified and direction and approval of GE.

M&L for Reinforced Cement Concrete Readymade Pole, type B-0 1:2:4 (12.5 mm graded aggregate) and set in Cement Mortar (1:4) size of RCC pole : 100x100x900mm and product is made up of good quality including all mouldings, necessary formworks and reinforcement and dismantling existing damaged RCC Pole in any description all as specified and direction and approval of GE.

M&L for RCC (1:2:4) type B-1(using 20 mm graded stone aggregate) as in cills, louvres, parapets, railing, coping, seismic and other similar bands, plinth bend, etc including weathering slightly rounded or chamfered angles and throuting , including necessary form work etc complete all as specified and directed.

M&L for RCC 1:2:4 using 20mm stone agg Type B1 using for gate Pillers, columns and posts etc complete all as specified and directed.

Form work to soffit of suspended slabs such as roof slabs, floor slabs, landings and similar work, n exc 200mm thick (horizontal or sloping) complete all as specified and directed.

S&F mild 6 to 8 mm dia deformed TMT bars cut ot length bent to shape required including cranbing, bending spirrally, hooking ends and binding with and including mild steel wire annealed net less than 0.9 mm dia or securing with clips complete all as specified and directed.

Dismentling wrought iron or mild steel work of such as grill/roof purlin etc not otherwise provided for complete all as specified & directed.

Mild steel framed work as in gates, grills, grating pintel higes stope hand made sliding bolts etc with ends of bars shouldered and /or riveted or forged into spikes framed guard bars and for ornamentals and intricate design conforming to Fe 410-0 or 310-0 of angle iron of other sections complete drilled for fixing of steel sheeting or other coverings to be prepared for handing or sliding with and incl either hooks and hinges doors( Exclusive of steel sheeting or other covering running rails and guides) and hanging also fastening and fixing with one shop coat of Zinc Chrmate pait (incl preparation of surface0 at contractor wksp before febrication, complete all as specified and directed.

M&L applying two coats of synthetic enamel paint over a coat of red oxide 0r zinc chromate primer including preparation of new steel or iron surfaces exc 10 cm width or girth, complete all as specified and directed.

Dismantling of fencing barbered wire any type complete all as specified and directed.

S&F Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails strain- ing bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etccomplete all as specified and directed.

S&F for Mild steel angle iron fencing post and sturts in fencing incl necessary cutting drilling welding etc and bending to swan neck shape as required and drilling holes notching for wives etc conforming to Fe-290 Gde E-165 complete all as specified and directed.

S&F for Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified and directed.

M&L for laying at or near ground level factory made kerb stone 450mmx300mmx150mm of M-25 graded cement concrete in position to the required line, level and curvature jointed with cement mortar 1:4 including making joints with or without grooves (thickness of joint except at Sharpe curve shall not be more than 5mm) including making drainage opening wherever required complete all as specified and directed by Engr-in-Charge (pre cast shall be approved by GE (I) R&D length of finished kerb shall be measured for payment).

M&L applying two coats of synthetic enamel paint on kerb tone over a coat of primer including preparation of kerb stone surfaces exc 10 cm width or girth, complete all as specified and directed.

Dismantling Stone slabs and tiles of any description or thickness in floors, aprons etc. complete all as specified and directed.

M&L for 20mm thick granite slab of any colour and shade (table rubbed and polished) including pointing in white cement (1:2) using marble dust , of superior quality set and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone over and including 15 mm thick screed bed in cement mortar 1:4, cutting the edges in bullnosed shaped and polishing complete all as specified and as directed.

S&F in repairs Galvanised mild steel wire cloth 0.63 mm nominal dia and average width of aperture 1.40 mm including cutting/welding/screwing etc complete all as specified and directed .

Hacking out old broken glass (any thickness, size, quality or description) from wooden or steel frames, glazed with putty or fixed with beads complete all as specified and directed.

S&F 3 mm thick sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

Dismantling floor and Wall tiling including cement mortar bedding (but backing) removing seviceable to store and rubbish off the premises complete all as specified and directed.

Roughening surface of old concrete floor by picking,sweeping clean and washing down with water to removing dust and brushing neat cement slurry with 0.3kg of cement per sqm complete all as specified and directed.

M&L non skid ceramic coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.06 sqm but not exceeding 0.11 sqm, in floor etc, set and jointed in neat cement slurry and pointed in white and coloured cement to match coloured tiles including Screed bed of mortar 15mm thick for laying floor finishes CM (1:6) complete all as specified and directed.

M&L non skid ceramic coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm, in floor etc, set and jointed in neat cement slurry and pointed in white and coloured cement to match coloured tiles including Screed bed of mortar 15mm thick for laying floor finishes CM (1:6) complete all as specified and directed.

M&L for glazed ceramic coloured tiles 300x450x7mm thick set and jointed in neat cement slurry and pointed in white cement with pigment or coloured cement to match shade of tiles in vertical surface over and including 10mm thick rendering in CM 1:4 complete all as specified and directed.

U.R ASSOCIATES

ESKEY COMPANY