DVDB Work in NCT of Delhi

Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including disposal of excavated earth upto 50 m and lift upto 1.5 m, disposed soil to be levelled and neatly dressed :All kinds of soil

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared.

Supply of earth including excavation, banking excavated earth in layers not exceeding 20 cm in depth, breaking clods watering, rolling each layer with 1/2 tonne roller, or wooden or steel rammers and dressing up in embankments for roads, flood banks, marginal banks and guide banks or filling up ground depressions by mechanical transport within 10 km. lead and lift upto 1.5m including royalty.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources).

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete etc. as per direction of Engineerin-in- charge (length of finished kerb edging shall be measured to calculate volume for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).

Providing and laying 60 mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making achine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge.

Laying one number PVC sheated / XLPE power cable of 1.1 KV grade of following size in the existing RCC/HUME/Metal pipe as required upto 35 Sq. MM.

Supplying and laying double walled corrugated (DWC) High Density Poly ethylene (HDPE) pipe of 100/SN8 size having corrugation on the outer wall and plain surface on inner wall confirming to DWC PIPE SN8 IS-16098-2 below the ground level excluding excavation refilling the trench etc. as per specification etc. as required

Supplying installation testing and commissioning of LED HW-SL 90-W HLSLD-ML04-90-CWL-DIMM-RTC(System Wattage) LED street light Luminaries with in high pressure die cast LM6 Aliminium/ extruded Aluminium housing, minimum 6900 Lumen output, CCT > 5700 K, for effective thermal managament, sturdiness and better aesthetics. Luminaries should be 140-270 Volt, surge protection > 5KV (additional SPD 5 KV inside Housing ), Driver efficiency should be > 85%THD < 10% Driving current of LED < 700 mA, phase to phase protection 415 Volt AC, individual lense for each LED for Better Uniformity. UV stablized polycarbonate / glass cover high ingress protection of IP 66 for complete luminaries. sutaible for side entry with GI (B Class ) bracket of 40-60 mm dia Pipe etc. complete as reqired (make Halonix/Bajaj/Havells)

Supplying & drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/recessed steel / PVC conduit as required 2 x 2.5 Sqmm

Supplying & drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/recessed steel / PVC conduit as required 2 x 2.5 Sqmm

Supplying & fixing 6 amps to 32 amps rating, 240/415 volts 'C' curve miniture circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connectionm testing and commossioning etc. as required A) Single Pole.

Supply of Three seats Modern Without Arm Rest RCC Concrete Bench With Round Table Mould chair with complete in all respect.

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick

Supply and installation of multi color FRD Fiber big Radhe Krishna Statue & 12ft for park. All complete item to be fixed in C:C (1:2:4) block after deep excavation/earth work at site as requried. The area covered 4.00 M x 4.00 M & safe walking area.

Supply and installation, testing and commissioning of energy efficient aluminium fancy street light poles with all accessories including connection with 1.5 mm FR PVC installed copper conductor singte core cable and earthing etc. as per directino of Engineer in charge.

Providing and fixing 18 mm thick gang saw cut, mirror polished,premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing,moulding and polishing of edges to give high gloss finish etc. completeat all levels.Area of slab upto 0.50 sqm

Providing and fixing expansion hold fasteners on C.C. /R.C.C./Brick masonry surface backing including drilling necessary holes and the cost of bolt etc complete.Fastener with threaded dia 12 mm

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1:3:6 or richer mix (including equivalent design mix)

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar

Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead : Of area 3 sq. metres and below

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil.

Centering and shuttering including strutting, propping etc. and removal of form forSuspended floors, roofs, landings, balconies and access platform

Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete

Centering and shuttering including strutting, propping etc. and removal of form forColumns, Pillars, Piers, Abutments, Posts and Struts

Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platform

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:4 (1 cement : 4 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundations and plinth in : cement mortar 1:4 (1 cement : 4 coarse sand)

6 mm plaster on cement concrete or reinforced cement concrete work with white cement based polymer modified self curing mortar of approved make as per the direction of Engineer-In-Charge.

15 mm cement plaster on the rough side of single or half brick wall of mix :1:4 (1 cement: 4 fine sand)

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve even shade and colour : New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre

Colour washing such as green, blue or buff to give an even shade :New work (two or more coats) with a base coat of whiting.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. Pre-laminated particle board with decorative lamination on both sides

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 5.50 mm thickness

Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge. (Only weight of grill to be measured for payment)

Providing and fixing fly proof stainless steel grade 304 wire gauge, to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia. 0.50 mm all completeWith 12 mm mild steel U beading

Providing and fixing ISI marked aluminium butt hinges anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with necessary screws etc. complete:125x75x4 mm

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete 300x16 mm

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 150x10 mm

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 300x10 mm

Providing and fixing aluminium tubular handle bar 32 mm outer dia, 3.0 mm thick & 2100 mm long with SS screws etc .complete as per direction of Engineer-in-Charge. Polyester powder coated minimum thickness 50 micron aluminium tubular handle bar

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :125 mm

Filling the gap in between aluminium/ stone/ wood frame and adjacent RCC/ Brick/ Stone/ wood/ Ceramic/ Gypsum work by providing weather/structural non sag elastomeric PU sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete, complying to ASTM C920, DIN 18540-F & ISO 11600Upto 10 mm depth and 10 mm width

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. 32 mm dia

Providing and fixing soil, waste and vent pipes : Sand cast iron S&S pipe as per IS: 1729

Providing and filling the joints with spun yarn, cement slurry and cement mortar 1:2 ( 1 cement : 2 fine sand) in S.C.I./ C.I. Pipes : 100 mm dia pipe

Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc. : For 100 mm dia pipe

Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 100 mm dia Sand cast iron S&S as per IS - 1729

Providing and fixing single equal plain junction of required degree : 100x100x100 mm Sand cast iron S&S as per IS - 1729

Providing and fixing terminal guard : 100 mm Sand cast iron S&S as per IS - 1729

Providing and fixing collar : 100 mm Sand cast iron S&S as per IS - 1729

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors :100 mm inlet and 100 mm outlet Sand cast iron S&S as per IS: 3989

Cutting chases in brick masonry walls for following diameter sand cast iron/ centrifugally cast (spun) iron pipes and making good the same with cement concrete 1:3:6 ( 1 cement : 3 coarse sand :6 graded stone aggregate 12.5 mm nominal size), including necessary plaster and pointing in cement mortar 1:4 (1 cement : 4 coarse sand) :100 mm dia

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design :100 mm diameter S.W. pipe

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the wall etc. 20 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 25 mm nominal outer dia Pipes

Providing and fixing uplasticised PVC connection pipe with brass unions :45 cm length 15 mm nominal bore

Providing and fixing uplasticised PVC connection pipe with brass unions :45 cm length 15 mm nominal bore

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. Circular tank

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :15 mm nominal bore

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15mm nominal bore

Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge.

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete : 250 mm diameter

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design :250 mm diameter S.W. pipe

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Provinding and installation of AERO RIDER. The area covered for 1.2 x 0.5 Mtr. & safe play area: 2.2 x 1.5 Mtr. The main frame of AERO RIDER is made from 100 NB & 40 NB galvenized pipe with polyester based powder coating of minimum 60 micron thickness. Handle Support pipe linked to seat via 25NB Galvanized pipe. Handle pipe consists of pipe grip of 20 NB G.I. Pipes with suitable PVC grip. The Handle pipe extended to connnect foot grip of 25 NB & 20 NB G.I. pipes via 40 NB Galvanized pipe. The Handle support pipe is pivoted over 100 NB & Support pipe with Zinc plate rectangular tube. The FRP Seat rest over the 75x10 mm M.S. Flat with G.I. plating hinged over the 100 NB main frame pipe with the help of heavy duty bush bearing. All pipes area uniformly powder coated up to minimum 60 micron thickness to avoid corrosion. All open ends of pipe been closed by GI/HDPE caps for user safety against enterpment. The G.I. pipe to be used of standard make and B-class. All complete item to be fixed in C:C (1:2:4) block after deep excavation/earth work at site as required.

Providing and installation of CHEST PRESS & SHOULDER EXERCISE COMBINATION. The area covered for product 2.3 x 1.2 Mtr. & Safe Play Area : 3.3 x 2.2 mtr. The centre frame of the Chest Press & Shoulder Exeercise Cobination is made up of 40 NB G.I. pipe bend and G.I. Sheet. Specially designed brackets are bolted to centre frame. These brackets are made of M.S material with G.I. plating. The connecting links are made of 40 NB G.I. Pipes which are mounted to main framed with the help of specially designed machined shaft and bush bearing. The handle frame is made of 25 NB galvanized pipe handle is linked to the seat with 40 NB ppe which is hinged to main vertical support pipe with the help os specially designed bush bearings. FRP Plastic seat fixed over 40 NB G.I. pipe seat frames. This seat frame is hinged over verticall support pipe through 40 NB galvanized pipe links with the help of specially designed bush bearings. Foot rest is made up of 20 NB G.I. pipes. Specially designed Nylon pads ara provided at the bottom of seat frame. All pipes are uniformly polyester based powder coated up to minimum 60 micron thickness to avoid corrosion. all open ends of pipe been closed by GI/HDPE caps for user safety against enterapment. The G.I. pipe to be used of standard make and B-class. All complete as per the technical specifications to manufacture the item. The complete item to be fixed in C:C (1:2:4) back after deep excavation/earth work at site as requred.

Provoding and installation of SEATED & STANDING TWISTER. The area covered for product 2.1 x 1.9 Mtr. & safe play Area : 3.1 x 1.9 Mtr. The main frame of seated & standing twister consists of 100 NB G.l . Pipe with handle attached on it. Handle pipe is made up of 25 NB G.l. pipe. two handles are attached to main frame in two different planes. The seated frame is made from 25 NB and 15 NB G.l. pipes which are further attached to round plate which acts as a rotating disc. Rotimng disc made from FRP plastic is supported over 100NB G.l. pipe stand with the help of specially designed heavy duty bearing shaft assemblies. Bearngs used are oil sealed, self-lubricated made by reputed company. Stand are bolted to main frame with the help of 40NB G.l. profile bend pipe. Foundation stands, made of 100 NB G.l. pipe and G.L plated M.S. round plates are provided. all pipes are uniformly polyester based powder coated up to minimum 60 micron thickness to avoid corrosion . All open ends of pipes been closed by Gl/HDPE caps for user safety against entrapment. The G.l. pipe to be used of standard make and B-class. All complete as per the techinal sprcification to manufacture the item. the complete item to be fixed in C:C (1:2:4) block after deep excavation/earth work at site as required .

Providing and installation of SKY WALKER. The area coverd for product 1.8 x 0.9 Mtr. & Safe Play Area : 2.8 x 1.9 Mtr. The main framed of SKY WALkER is made from 100 NB & 40 NB Galvanized pipe. The handle pipe consists of 25 NB Galvanized pipe with PVC grip on top end. This handle pipes are hinged over 100 NB main frame with the help of specially designed heavy duty bearing. bearings used are of standard make. The handle pipe is further extended to the rectangular tube of 50 x 25 mm on both side with 40 NB galvanized pipe link. Paired rectangular tubes with four foot rests are linked to main frame. Foot rest is made with the help of high quality FRP (Fiber Reinforced Plastic) material. Total structure is supported on base frame made up of rectangular pipe of 100x40 mm. Side frames are made up to 25NB galvanized pipes. All pipe are uniformey polyster based powder coated up to minimum 60 micron thickness to avoid corrosion. All open ends of pipe been closed by GI/ HDPE caps for user safety against entrapment. The G.I. pipe to be used of standard make and B-class. All complete as per the techinal sprcification to manufacture the item. the complete item to be fixed in C:C (1:2:4) block after deep excavation/earth work at site as required .

Providing and installation of LEG PRESS DOUBLE STANDARD. The area coverd for product 2.2 x 0.6 Mtr. & Safe Play Area : 3.2 x 1.6 Mtr. The main framed of Leg press consist of 100 NB G.I. pipe with two specially designed brackets attached on it. Brackets are made of M.S. material with G.I. plating. The moving frame of Leg press in made of 40 NB G.I. pipes which are mounted to main frame with the help of specially designed machined shaft and bearing housing. Bearings used are oil sealed, self-lubricated made by reputed company. Foot rest is hinged to main frame with the help of specially designened G.I. plated clamp and 25 NB G.I. pipesGusset plate are provided to give extra strength to foot rest. Foot rest is made with the help of high quality FRP (Fiber Reinforced Plastic) material. Specially designed Nylon pads are provided at the bottom of moving frame. Seat and Back rest provided are made of FRP plastic. All pipes are iniformally polyster based powder coated up to minimum 60 micron thickness to avoid corrosion. All open ends of pipe been closed by GI/ HDPE caps for user safety against entrapment. The G.I.pipe to be used of standard make and B-class. All complete as per the techinal sprcification to manufacture the item. the complete item to be fixed in C:C (1:2:4) block after deep excavation/earth work at site as required .

Providing and installation of AERIAL STROLLER. The area covered for product 1.0 x 0.5 Mtr. & Safe Play Area : 2 x 1.5 Mtr. The main frame of AERIAL STROLLER is made up of 100 NB G.I. pipes with G.I. plating upto 40 micron thickness. This main frame is rest on 100 NB G.I. pipes to give it strength. Foot rest bend pipe is made up of 40 NB G.I. pipes. Foot rest is made with help of high quality FRP (Fiber Reinforced plastic ) material foot rest is mounted on main frame with the help of sepcially designed bearing assembly for its free movement. Bearings used are oil sealed, self-lubricate made by reputed compnay. Handle is made by 25 NB G.I. pipes. All pipes are uniformly polyester based powder coated up to minimum 60 micron thickness to avoid corrosion. All open ends of pipe been closed by GI/HDPE caps for user safety against enterapment. The G.I. pipe to be used of standard make and B-class. All complete as per the technical specifications to manufacture the item. The complete item to be fixed in C:C (1:2:4) blcok after deep excavation/earth work at site as required.

Providing and installation of HAND POWER. The area covered for product 1.4 x 1.0 Mtr. & safe play Area : 2.4 x 2.0 Mtr. The main frame of Hand Rower rest on 100 NB G.I. pipe and FRP (Fiber Reinforced Plastic) seat with backrest is fixed over 40 NB Glavanized bend pipe. This bend pipe is further linked to 100 NB base pipe with help of connecting links. Connecting links are made up of 25 NG G.I. pipes with specially designed metal bush at ends. The paired 25 NB pipe handle with rubber grip at the end is fixed over one of the connecting link. the rolling frame is made by 40 NB & 20 NB G.I. pipes. Connecting links are hinged in between seat frame and base frame with specially desinged bush bearings. A suitable PVC/ rubber grip is provided for foot rest on seat frame. All pipes are uniformly polyester based powder coated up to minimum 60 micron thickness to avoid corrosion. All open ends of pipe been closed by GI/HDPE caps for user safety against enterapment. Handle for roating the ring fixed over the pipe ring. The G.I. Pipe to be used of standard make and B-class. All complete as per the techancial specificatins to manufacture the item. The complete item to be fixed in C:C (1:2:4) block after deep excavation/earth work at site as required.

Providing and installation of SIT UP BOARD. The area coverd for product 2.5 x 0.9 Mtr. & Safe Play Area : 3.5 x 1.9 Mtr. The main framed of SIT UP BOARD is made up of 50 x 50 x 3 mm thick rectangle tube with leg support structure. The back rest is fixed over 40 NB back rest frame. Back rest is made up of rectangular pipes of 50 x 25 x 3 mm thick. All pipes are uniformly polyester based powder coated up to minimum 60 micron thickness to avoid corrosion. All open ends of pipe been closed by GI/HDPE caps for user safety against enterapment. The M.S pipe to be used of standard make and med duty type. All complete as per the techanical specifications to manufacture the item. The complete item to be fixed in C:C (1:2:4) block after deep excavation/earth work at site as requried.

Providing and installation of SHOULDER TWIRL. The area coverd for product 2 X 0.9 Mtr. & Safe Play Area : 3 x 1.9 Mtr. The main frame of SHOULDER TWIRL is made by 100 NB and 25 Galvanized pipe bend to from ring and spokes consists of 20 NB G.I. pipes that connect to each other to form a wheel of SHOULDER TWIRL. This wheel is fixed to 100 NB main support galvanized pipe with the help of 40 NB connector pipe with specially desinge bearing. Bearing used are oil sealed, self-lubricated made by reputed company. All pipe ae uniformly polyester based powdeer coated up to minimum 60 micron thickness to avoid corrosion. All open ends of pipe been closed by GI/HDPE caps for user safety against enterapment. Handle for roatating the ring fixed over the pipe ringh. The G.I. pipe to be used of standard make an dB-Class. All complete as per the techanical specifidations to manufacture the item. The complete item to be fixed in C:C (1:2:4)block after deep excavation/earht work at site as required.

Providing and installation of FOREARM TWIRL. Product Area 1.5 X 0.8 Mtr. & Safe Play Area :2.5 x 1.8 Mtr. with the 25 NB Galvanized pipe bend to form ring and spokes consists of 20NB G.I. pipes that connect to each other to from Two wheel of FOREARM TWIRL. This wheel is fixed to 100 NB main support galvanized pipe with the help of 40 NB connector pipe with specially designed bearing. Bearing used are of standard make. All pipes are uniformly polyester based powder coated up to minimum 60 micron thickness to avoid corrosion. All open ends of pipe been closed by GI/ HDPE capes for user safety against entrapment. Handle for roating the ring fixed over the pipe ringh. All complete as per the techanical specifications to manufacture the item. The complete item to be fixed in C:C (1:2:4) block after deep excavation/earth work at site as requried.

Providing and installation of ABS BOARD. The product Area: 1.6 x 0.8 Mtr. & Safe Play Area: 2.6 x 1.8 Mtr. Which is included The main framed of ABS Board is made up of 80 NB G.I. pipes with leg support structure. The Back rest is fixed over 40 NB back rest frame. Back rest is made up of rectangular pipes of 50 x 25 x 3 mm thick. All pipes are uniformly polyester based powder coated up to minimum 60 micron thickness to avoid corrosion. All open ends of pipe been closed by GI/HDPE caps for user safety against entrapment. All complete as per the techanical specifications to manufacture the item. The complete item to be fixed in C:C (1:2:4) block after deep excavation/earth work as site as required.

Providing and installation of SHOULDER EXERCISE DOUBLE. Product Area : 2.2 x 0.9 Mtr. & Safe Play Area : 3.2 x 1.9 Mtr. The main frame of Seated puller consists of 100 NB G.I. Pipe with two specially designed brackets attached on it. Brackets are made of M.S material with G.I. plating. The connecting links are made of 40 NB G.I. Pipe which are mounted to main frame made of 25 NB galvanized pipe. Handle is linked to the seat with 40 NB pipe which is hinged to main vertical support pipe with the help of specially designed bush bearing. HDPE/LLDPE plastic seat fixed over rectangular tube of 80 x 40 mm with zinc plating for corrosion resitance. This seat frame is hinged over vertical support pipe thorugh 40 NB galvanized pipe links with the help of specially designed bush bearings. Foot rest is made up of 20 NB G.I. pipes. Specially designed Nylon pads are provided at the bottom of seat frame. All pipes are uniformly polyester based powder coated up to minimum 60 micron thickness to avoid corrosion. Alll open ends of pipe been closed by GI/HDPE caps for user safety against enterpment. All complete as per the technicall specifications to manufacture the item. The complete as per the techanical specificatio to manufacture the item. The complete item to be fixed in C:C (1:2:4) block after deep excavation/earth work at site as required.

Providing and installation of Multicolor Kids Multi Playstation, Size : Standard. Which is included The main framed of is made up Multi Playstation of 100 NB G.I. pipes with leg support structure. All pipes are uniformly polyester based powder coated up to minimum 60 micron thickness to avoid corrosion. All open ends of pipe been closed by GI/HDPE caps for user safety against entrapment. All complete as per the techanical specifications to manufacture the item. The complete item to be fixed in C:C (1:2:4) block after deep excavation/earth work as site as required.

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group C

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.2 X 4 sq. mm + 1 X 4 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.2 X 6 sq. mm + 1 X 6 sq. mm earth wire

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole and neutral

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Double pole

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Triple pole and neutral

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 A & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

Supplying, installation, testing and commissioning of energy efficient prewired baton fluorescent LED light 18 watt natural white with high efficient with all accessories including connection with 1.5sq mm FR PVC insulated copper conductor single core cable and earthing etc. (Making Bajaj/ Surya /Havells /Phillips /Helonix /Crompton).

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc. as required.

Supplying, installation, testing and commissioning of 1200mm sweep AC electric ceiling fan capacitor type with double ball bearing complete with down rod, canopies, shackless, blades but without regulator suitable for operation on 230/240 volts, 50HZ single phase AC supply including wiring the down rod of standard length up to 1mtr with 2x1.5 Sq.mm PVC insulated copper conductor with fan sheet etc. as required. (Make Bajaj/Havells/Usha/C.G.)

Supplying and fixing of LED 15/16 Watt ceiling light fitting including surface mounted downlightj with white powder coated connection, testing and lamp as required. Bajaj/havells/halonex etc. as required.

Providing and fixing 34/36 Watt LED Panel of Size 600 x 600 mm square type LED fitting for (recess) to be fixed in the ceiling with the help of fastners and rawal plug. (Havells, Wipro, Panasonic, Crompton, Helonix)

Supplying, testing and commissioning of PVC insulated armoured and PVC sheathed (General purpose) multi core cable with standard aluminium conductor suitable for working voltage upto including 1100 volt confirming to IS 1554/pt/88 with amendment no. as required 2x6 sqmm (Finolex, Havells, Polycab, Grandly)

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size on wall surface as required. Upto 35 sq. mm (clamped with 1mm thick saddle)

Suppying, installation, testing and commissioning of 70/72 watt LED 6000K asymmetric new generation energy saving and environment long life versatile pressure die cast aluminum IP66 roadway luminaries with high power LED light source complete etc. as required housing reflector and enclosed with toughened glass complete with all accessories, Phillips/Bajaj/Crompton/Helonix/Havells (Model LHFAUX7DNP6J070).

Supplying and fixing of 32 mm ida x 2.00 meter long G.I. pipe (medium class) bracket for mounting of fluorescent / HPMV / HPSV street light fitting on pole including bending the pipe to the required shape, 2 Nos. 40mm x 3 mm falt iron clamps with nuts, bolts, and washer, painting the flat iron with primer and finish paint etc. as required.

Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.

Supplying and installation 2.00 Tonne AC manufacturing Brank LG, Tata, Voltas, Godrej Etc. As per Engineer-in-Charge.

Please Enable Macros to View BoQ information