PROVN OF 01 X TOILET FOR COOK HOUSE AND STEEL GATE AT 1803 PNR UNIT, PROVN OF CYCLE SHED, 01 X STORE ROOM, STORAGE ACCN AND PROVN OF TILES WORK INFRONT OF BLDG NO T-370 (QG) AT 1803 PNR UNIT, PROVN OF ALUMINIUM JOINERY AT BLDG NO BI-15 (JCO CLUB), P

Amount

SCHEDULE 'A' PART-I (B/R WORKS) Demolition of brick work built in cement mortar including all quoins, arches, pillars etc., but excluding ashlar facings, dressed stone work and precast concrete articles, all as specified and as directed by the Engineer-in-Charge.

Demolition of cement concrete (unreinforced) in ground floor and paving n.exc 15 cm thick below or above GL complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description in rafters, purlins and wind ties etc complete all as specified and directed.

Dismantling of plain or corrugated steel/ fibre glass sheeting any gauge or any thickness in roof covering including stacking serviceable materials of re-use and removing unserviceable materials complete all as specified and directed.

Surface excavation n exc 30cm deep and averaging 15cm deep and getting out in hard/dense soils, complete all as specified and directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 Sqm on plan and n exc 1.5 m in depth and getting out in soft/loose soils, complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 Cm in soft/loose soils, complete all as specified and directed.

Removing excavated materials not exc 50 m and depositing where directed at a level not exc 1.50 m above the starting point complete all as Specified and as directed.

Removing excavated material exc. 250m but n exc. 500m where directed at a level not exc 1.50 m above the starting point complete all as Specified and as directed.

M&L for moorum/red bajri filling in floors or pavings, laid in layers not exceeding 15 Cm thick, levelled and rammed including watering, complete all as specified and directed.

M & L for hardcore of gauge not exc 63 mm, deposited, spread and levelled in layers not exceeding 15 Cm thick, watered and rammed to true surface with broken stones complete all as specified and directed.

M & L for plain cement concrete (1:3:6) type C-2 using 40 mm graded stone aggregates as in foundation filling, sub base as in floors and mass concrete complete all as specified and directed.

M&L Brick Work with fly-ash Bricks (with Old Size Bricks), Straight or Curved on Plan exc. 6.0 Metre mean Radius, built in Cement Mortar 1:6, complete all as specified and as directed.

M&L Brick Work with fly-ash Bricks Half-Brick thick, Old Size, built in Cement Mortar 1:4, Straight or Curved on Plan to any Radius, complete all as specified and as directed.

M&L for rendering 15 mm thick built in cement mortar (1:4) on fair faces of brick work or concrete surfaces finished even & smooth (without using extra cement) and mixed with water proofing compound as per manufacturer's instruction complete all as specified and directed. (NOTE : Water proofing compound shall be measured and paid separately).

Supply only liquid water proofing compound all as specified and as directed.

M&L for 15mm thick rendering on fair faces of brick work or concrete surfaces in cement mortar 1:4 finished rendering surfaces even and smooth without using extra cement complete all as specified and directed.

M&L for 10mm thick rendering on fair faces of brick work or concrete surfaces in cement mortar 1:6 finished rendering surfaces even and smooth without using extra cement complete all as specified and directed.

Use and waste of formwork to sides of concrete foundations, footings, bases of column, raft and raft beams, side and soffit (if any) for foundation and plinth beams etc, vertical or to batter for rough finished surfaces complete all as specified and directed.

Use and waste of Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc., for rough finished surfaces, complete all as specified and directed.

Use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200 mm thick (horizontal or sloping) for fair finished surfaces complete all as specified and directed.

M&L for M-25 nominal mix RCC (1:1½:3), type A-1 (using 20mm graded stone aggregate) as in foundations, rafts, footings, foundation beams, plinth beams, base of columns, basement of slabs, underreamed piles and mass concrete etc., complete all as specified and as directed.

M&L for M-25 nominal mix RCC (1:1½:3), type A-1 (using 20mm graded stone aggregate) as in beams, cantilevers, bressumbers, lintels, over 1.50m span etc., complete all as specified and as directed.

M&L for M-25 nominal mix RCC (1:1½:3), type A-1 (using 20mm graded stone aggregate) as in slabs supported on walls, beams, columns in floors, roofs, landings, balcones, canopies, duck slabs, shelves and like etc., complete all as specified and as directed.

M&L for M-25 nominal mix RCC (1:1½:3), type A-1 (using 20mm graded stone aggregate) as in Chajjas and in shelves and the like etc., complete all as specified and as directed.

M&L for mild steel TMT Bars 10 mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including Mild Steel Wire (annealed) not less than 0.90 mm or securing with clips, etc., complete all as specified and as directed.

M&L for mild steel TMT bars 5 mm dia and over upto and including 10 mm dia in stirrups , spacers and binders cut to length , bent to shape required as in reinforcement and binding with MS wire (annealed) not less than 0.90 mm dia complete all as specified and directed .

M&L 100 mm thick PCC (1:3:6) type C-2 (using 40mm graded crushed stone aggregate) as in sub base of floors, complete all as directed by the Engr-in-Charge.

M&L 75 mm thick PCC (1:3:6) type C-2 (using 40mm graded crushed stone aggregate) as in plinth protection, finished even and smooth without using extra cement as directed by the Engr-in-Charge.

M&L 100 mm thick PCC (1:2:4) type B-1 (using 20mm graded crushed stone aggregate) as in floors, finished even and smooth without using extra cement as directed by the Engr-in-Charge.

M&L for glass dividing strips 3mm thick, 38mm width of strip inserted in position, confirm to design in concrete floor, complete all as directed by the Engr-in-Charge.

M & L for 40 mm thick PCC 1:2:4 type B-1 (using 20 mm graded aggregate) as in floor, finished even and fair for flooring of tiles, complete all as specified and as directed

M&L for plain cement concrete (1:2:4) type B1 using 20 mm graded aggregates in lintels upto 1.5 m clear span, cills, steps, seismic and other similar bands, plinth courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones , bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating including formwork complete all as specified and directed.

S&F Non-skid ceramic coloured tiles (square/ rectangular), 7 to 8 mm thick, area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, set and jointed in neat cement slurry in floors and pointed in white or coloured cement to match the shade of tiles, laid over and including 15mm thick screed bed or bedding layer in cement mortar 1:6 complete all as specified and directed.

M&L glazed coloured digital ceramic tiles in vertical surface 300 X 450 X 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the colour of tiles, laid over and including 10mm thick rendering in cement mortar 1:3 complete all as specified and directed.

M & L for pre-polished Chequered cement concrete tiles (coloured) of size 30cmx30cmx25mm thick , set , jointed and pointed in neat cement slurry in floor and pointed with white/coloured cement & pigment to match the surface laid over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

Supply and fixing 25 mm thick pre-polished decorative cement concrete tiles of size 300mm x 300mm, as in flooring over and including 20mm thick backing layer of cement mortar (1:6) set and jointed in neat cement slurry and pointed in white cement mixed with admixture pigment to match the shade, as directed by Engineer-in-Charge.

M&L for Coloured granite (of any type) work, 18-20 mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms, urinal partition and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and making moulds on edges laid over and including 15 mm thick screed bed in cement mortar 1:4 complete all as specified and directed.

Providing edge moulding to 18-20mm thick granite stone, any description of counters vanities etc. including machine polishing to edge to give high gloss finish etc. complete all as specified and directed.

S&F in position, at or near ground level, factory made precast cement concrete kerb stone blocks, in M-25 grade cement concrete, fixed to the required line, level and curvature, jointed in cement mortar 1:3, including making joints with or without grooves (thickness of joints, except at sharp curves shall not be more than 5 mm) including making drainage opening wherever required complete all as specified and directed.

Supply and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as specified and directed. (NOTE: Cost of sand cushioning is deemed to be included in the quoted rates)

S&F for 2nd class hardwood, plain, solid, straight chowkats and frames, wrought, framed, rebated on the solid, moulded or chamfered, put together with glue, pinned at joints complete all as directed.

S&F Factory made 30mm thick with 2nd class hard wood, rail and style factory made plain framed panelled shutter(two panel) with lock, rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail & style as per IS:1003(Part-I) kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F Factory made solid PVC door frame (chowkhat) of size 50 mm x 47mm made out of 5mm plain colour PVC sheet, frame reinforced with MS square tube, fixed in opening as per specification & drg as per manufacturer instructions complete all as specified and directed.

M&L for Factory made solid PVC moulded door shutter, 28 to 30 m thick(stiles) with 2,4 or 6 raised panel design with 2 mm thick moulded PVC sheet on the front face & 2 mm plain colour PVC sheet on back face with particle board core complete all as specified and directed.

Supply & fixing 100 mm mild steel butt hinges(medium weight) cold rolled complete all as specified and directed.

S&F aluminium handle, cast type anodised 150 mm size complete all as specified and directed.

S&F Aluminium handles, cast type, anodised, 125 mm complete all as specified and directed.

S&F 200 mm aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F 150 mm aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F 300 mm aluminium, anodised sliding door bolt with hasp, staple(bolt type) and fixing clip of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy complete all as specified and directed.

S&F 150 mm over all length of cover plate of floor door stopper of Brass body and tongue, anodised with hard drawn steel spring fixed in floor complete all as directed.

S&F 300 mm mild steel ordinary rat tail rod pattern springs including roller and roller plate all as specified and directed.

S&F stainless steel wire cloth of 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

Supply and fixed Steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded for fixing wire mesh including one shop coat of priming, complete all as specified and directed. (NOTE : Sheet glass for glazing and wire cloth for mosquito proofing shall be measured and paid separately)

S&F Aluminium anodised Powder coated for doors, windows, ventilators and partition with one or more rebate (minimum thickness of powder coating 50 micron) and three track with 1.8 mm thick channel section and shutter frame thickness 1.65mm, without sash bars, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc complete all as specified and directed. Notes: 1) Size of window shall be as per site requirement. 2) Glass and wire cloth shall be measured separately.

S&F anodised Aluminium grill (anodised transparent or dyed to required shade according to IS 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200mm centre to centre, including cutting the frill to proper opening size for fixing and operation of handles and fixing approved anodised Aluminium standard section around the opeing, all complete as per requirement and directed of Engineer-in-Charge.

S&F 4.8 mm thick sheet glass frosted on one side, area in squares exc 0.5 sqm in each pane and glazing with rubber gasket fixed to aluminium frame work / snap beading complete all as specified and as directed by the Engineer-in-Charge

S&F 4 mm thick sheet glass, ordinary quality, glazing with cleats, glazing clips, rubber neoprene packing etc, in squares exceeding 0.5 sqm in each pane complete all as specified and directed.

Providing and fixing factory made uPVC white colour Sliding window Three track, area not exceeding 2.00 sqm each, made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories complete all as specified and directed. (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net Opening will be measured lor payment purpose.)

S&F False ceiling with 'E' board "Classic", reinforced, designer series, board with HPSC of size 600 mm x 600 mm x 4 mm thick fixed on powder coated aluminium snap grid to support the boards/files with powder coated aluminium anodised main 'T' section 36mm x 25mm x 1.40mm, cross tee 23.50mm x 23.50mm x 1.40mm thick and aluminium angle 25mm x 25mm x 1.40mm as on edges/sides, fixed to ceiling with hangers 6mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long complete all as specified and as directed. (NOTE: Quoted rate shall be deemed to be inclusive of the cost of ceiling board)

M&L mild steel work in tubular trusses including special shaped washers etc complete using ERW or induction butt welded tubes conforming to IS-1161:2014 grade St-240 complete all as specified and directed. (NOTE: Quoted rates shall be deemed to include for cutting to dead length where required, notching, drilling, fitting, riveting and/or welding or connecting with bolts and nuts (including rivets or bolts and nuts), providing and fitting angle cleats, fish plates, gusset plates etc., also for wedging, plumbing, truing up and fixing complete)

M&L for structural steel work Fe 410-W (Gde-E-250) quality-A in roof trusses (framed), trussed, purlins, crane gantries, rials and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. complete all as specified and as directed by the Engineer-in-Charge. (NOTE: Quoted rates shall be deemed to include for cutting to dead length where required, notching, drilling, fitting, riveting and/or welding or connecting with bolts and nuts (including rivets or bolts and nuts), providing and fitting angle cleats, fish plates, gusset plates etc., also for wedging, plumbing, truing up and fixing complete)

Supply and fixing Rolled mild steel in joist, channel, angle, or tee section fixed independently, upto a height of 6 metre from each floor level (cut to ordinary length i.e. within 20mm of the length indicated) of FE-410- W(Gde-E-250) quality-B including using iron props and steel plates to existing RCC overhead members like beams, slabs etc., so as to ensure safety of existing structure and floor during repairing works complete all as specified and as directed.

M&L Mild steel framed work such as grills of ornamental type, gratings, etc with ends of bars shouldered and/ or riveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walkways, railings, framework of water tanks and similar works incl portions framed and hung as gates, including pintle hinges, stops, hand-made sliding bolts, etc confirming to grade Fe-290. Gde-E-165 complete all as specified and directed.

S&F rolled mild steel Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment confirming to FE-410-W (Gde E-250) complete all as specified and directed.

S&F Mild steel screw bolts (machine made) with hexagonal or square head one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut. exc 12 n. exc 20 dia of neck and exc5cm but n exc 10cm long, complete all as specified and directed.

M&L for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and directed.

M&L Preparing new plastered surfaces of walls and applying Two Coats of Distemper Oil Emulsion finished with rollers over a coat of alkali resistant primer complete all as specified and as directed.

M&L Preparing new plastered surfaces of walls and applying Two Coats of Distemper Oil Emulsion finished with rollers over a coat of alkali resistant primer and applied over and including 1.5 mm thick wall putty complete all as specified and as directed.

M&L for applying two coats of exterior acrylic emulsion weather proof paint over a coat of suitable exterior primer (as per manufacturer's instructions) including preparation of newly plastered surfaces of walls of any description, over 10cm width or girth not otherwise described, complete all as specified and directed.

M&L for preparation of surfaces and applying two coats of cement base paint over a coat of alkali resistant primer with brush on new plastered surfaces complete all as specified and directed.

M&L for applying two coats of synthetic enamel paint over a coat of pink primer on new wood or wood based surface exceeding 10 cm in width or girth including preparation of surfaces complete all as specified and directed.

M&L Preparing new Steel or Iron Surfaces of any description, over 10 Cm width or girth and applying Two Coats of Synthetic Enamel Paint over a coat of Red Oxide/ Zinc Chrome Primer, complete all as specified and as directed.

S&F Vitreous China table top Wash Basin 565 x 425 mm in size, White with 32mm dia Brass Chromium Plated Waste Fitting, making good disturbed Surfaces in Cement Mortar 1:3 complete all as specified and as directed. (MAKE : JAQUAR, Cat No: KUS-WHT-35935 / CERA, Model: CHEST / HINDWARE, Cat No. 91069 or equivalent model in PARRYWARE)

S&F Vitreous China (coloured) wash down water closet pan (pedestal pattern) with 'P' or 'S' trap front or back inlet, fixing bolts (except flushing cistern and flush pipe) incl plastic water closet seat cover (white) and mild steel chromium plated or aluminium hinging device complete all as specified and directed. (Make : Partyware, Model : Elite / JAQUAR, Model: Continental / CERA, Model: Conventional / HINDWARE, Model: SLICK)

S&F White PVC Flushing Cistern 10 Litre capacity, Low Level Valve Less, Symphonic Action type with Inlet, Ball Valve, Float, flush pipe and Handle including Cutting and pinning in Ends, making good disturbed Surfaces in Cement Mortar 1:3 and fixed including taking down/out unserviceable Flushing Cistern and connected items complete all as specified and directed. (MAKE : PARRYWARE, Model : Slim line Economy / HINDWARE, Model : Sleek Plus / CERA, Model : Corona / PRAYAG, Model: SMART or equivalent model in COMMANDER )

S&F 600mm x 450 mm mirror with PVC frame and fixed to wooden plugs with chromium plated brass screw and cup washers, as in repairs, complete all as specified and directed. (Make: PRAYAG, Cat No: 553 or equivalent model in other makes specified in CA)

S&F Soap dish, Vitreous China (white) Approximate size 160 x 160 x90mm, complete all as specified and directed. (Make : Partyware / JAQUAR/ CERA / HINDWARE)

S&F Towel Rail 600mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats. (Minimum weight 190gms) complete all as specified and directed . (MAKE : ESSCO, Cat No : AEC-1111 / PRAYAG, Cat No : BA-10/ SOMANY, Model: ETHER / JAINKO, Cat No: TRJ-2)

S&F Chromium plated brass Bib cock, long body with wall flange fixed to 15 mm bore of Iron pipe as in repair complete all as specified and directed. (Make : ESS ESS Cat No. RO-102, Essco, Cat No: MQT-512 / PRAYAG, Cat No: 7209/ SOMANY, Model: ETHER / JAINKO, Cat No: LNJ-1)

S&F 15mm bore chromium plated two way bib cock with flange, fancy type as directed. (Make : Ess Ess, Cat No: C-203 / JAQUAR, Cat No: CON-041KN/ PARRYWARE, Cat No: G1434A1 / CERA, Model : OCEAN / PRAYAG, Cat No: 9212/HINDWARE, CAT No: F330004CP)

S&F chromium plated Hand shower (health faucet), ABS body with 1.2 metre long flexible tube in chrome finish with wall hook, as in repairs, complete all as specified and directed. (MAKE : JAQUAR, Cat No : ALD-CHR-593/ CERA, Cat No: F8030401AB / ASIAN PAINTS, Cat No: C-232N / CERA, Cat No: F8030401AB / HINDWARE, Cat No: F160013 or equivalent model in PARRYWARE)

S&F 15 mm bore stop cock (surface type), cast copper alloy, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, as in repairs, complete all as specified and directed. (MAKE : ESSCO, Cat No : DLX-513A/513B / PRAYAG, Cat No : 7226/7228 or equivalent model SOMANY/ JAINKO)

S&F 15 mm bore fancy type stop valves, cast copper alloy, chromium plated (concealed type), screwed down, high pressure, with crutch or butterfly handle, incl concealed body, screwed both ends for iron pipe or for unions and, complete all as specified and directed. (MAKE : ESS ESS, Cat No: TM-332 & E221 / CERA, Model: F200351 & F4050102 /JAQUAR, Cat No: FLR-5083NK & ALD-083 / PARRYWARE, Cat No : G0651A1 & G5052A1 / / PRAYAG, Cat No: 9318 & CPS-15/ HINDWARE, Cat No: F280027 & F850096)

S&F 15mm bore heavy duty PVC connector pipe of length 450 mm with PTMT coupling at both ends, screwed down for pipe as directed. (MAKE : PRAYAG, Cat No. 323 / POLYTUF, Cat No. 4003 or equivalent model in SHAKTI / JEXON / CERA)

S&F Chromium plated brass Angular stop cock, fancy type, concealed type with wall flange fixed to 15 mm bore iron pipe complete all as specified and directed. (Make : JAQUAR, Cat No: KUP-35053PM / PARRYWARE, Cat No: T3097A1 / CERA, Cat No: F1005201 / PRAYAG, Cat No: 9410 / HINDWARE, Cat No: 320006 )

Supply and fixing Swivel Shower of PTMT of any colour for iron pipe and fixed for 15 mm bore pipe (Minimum weight 40gms) complete all as specified and directed.

Supply and fixing Shower arm 15mm size, 195mm long with bend of 45 degree with flange of PTMT of any colour (Minimum weight 40gms) for iron pipe and fixed for 15 mm bore pipe complete all as specified and directed.

M&L for 100 mm dia cast iron Nahani trap with grating including jointing to waste pipe fixed in cement concrete type B1(1:2:4) complete all as specified and directed.

Supply and fixing 100 mm bore cast iron (sand cast) soil, waste and vent pipes, in any length with or without ears, with cement joints, laid in trenches or in floors complete all as specified and as directed. (Note : Earthwork to be measured and paid separately).

S & F CI bend (any radius), diminishing pieces or tapers (larger bore measured) for 100 mm bore pipe complete all as specified and directed.

Supply and fixing 100 mm bore cast iron (sand cast) bends with access door (any radius), diminishing pieces or tapers (larger bore to be measured) complete all as specified and as directed by the Engineer-in-Charge.

Material and labour of CI (sand cast) Branch pieces, single (any radius, equal or unequal) for 100 mm bore pipe for any building height complete all as specified and directed.

S&F GI tubes 15mm bore "medium grade" with all fittings such as union, bend, angle, tee etc., and fixed complete to wall and ceiling or laid in floors, complete all as specified and directed.

All as per item No.95 here-in-before but 20 mm bore

Supply, hoisting and fixing rotational moulded polyethylene water storage tank (cylindrical vertical type with closed top) of capacity 1000 Litres, multi-layered (ISI marked), with GI tank nipple & cover, hoisted and fixed in position all as specified in SSR Part-I, complete all as specified and directed.

S&F 20 mm bore Ball brass valves, high pressure, with HDPE float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed. (MAKE : PRAYAG, Cat No. B-152 or equivalent model in JEXON / POLYTUF / SHAKTI)

S&F Chromium plated brass Angular stop cock, fancy type, concealed type with wall flange fixed to 15 mm bore iron pipe complete all as specified and directed. (Make : JAQUAR, Cat No: KUP-35053PM / PARRYWARE, Cat No: T3097A1 / CERA, Cat No: F1005201 / PRAYAG, Cat No: 9410 / HINDWARE, Cat No: 320006 )

S&F 0.50 mm thick TCT (total coated thickness) pre-coloured galvalume sheets with minimum base metal thickness of 0.45 mm, single skin high rib/multi rib profile galvalume sheeting having 1000-1020 mm width and 28-30 mm high crest @ maximum 250-255 mm pitch (centre) with sheets manufactured out of 0.50 mm this TCT (total coated thickness) high tensile galvalume sheets having tensile strength 550 MPA with 18-20 micron top coat over 5 micron primer and 8-10 micron alkyld backer zinc aluminium alloy AZ-150, sheets having a dip metallic zinc (43.5%0 aluminium (55%) & silicon (1.5%) with total mass coating of 150 gms/sqm on both sides, having wide pans with minimum 3 small stiffening ribs for effective water shedding and special male/female ends with full return legs on laps for purlin support and fixed as per existing profile of roof / cladding to walls, complete all as specified and directed.

All as per Item No.100.00 above, but 0.50 mm thick coloured plain galvalume sheet as in ridge/valley gutter of roof.

SCHEDULE 'A' PART-II (ELECTRIFICATION WORKS) M&L for concealed type point wiring with 1.50 Sq. mm (nominal area) FRLS-H PVC insulated and unsheathed, multi stranded copper conductor cable 1100 Volts grade, single core, laid in and including PVC conduit complete with all fittings and accessories, fixed to walls/ceiling, including galvanised mild steel terminal boxes 1.25 mm thick conforming to IS-5133 (Part-I) with 3.0 mm thick plastic laminated sheet top cover (ISI Marked) for mounting switches/ regulator /bell push etc and including 1.50 Sq. mm (nominal area) FRLS-H PVC insulated and unsheathed multi stranded copper conductor cable 1100 Volts grade, single core, earth continuity conductor connected to common earth dolly, for one light point /bell point/ ceiling fan/exhaust fan point controlled by one way switch complete all as specified and directed. (NOTES: - (i) Where tube light fitting is to be fitted/suspended, CI Circular boxes shall be provided with the PVC Pipes in the ceiling & the unit rate shall be deemed to be included for the same. (ii) Cost of cutting chases for concealed wiring shall be deemed to be inclusive in the quoted rates. No claim in this regard shall be entertained at a later stage)

All as per item No. 102.00 above but for one 5 amps switch socket outlet on same board controlled by another switch, complete all as specified and directed (concealed type point wiring with terminal box).

All as per item No. 102.00 above but for one 5 amps switch socket combination on independent board, complete all as specified and directed (concealed type point wiring with terminal box).

All as per item No. 102.00 above but using 2.5 sqmm single core multi stranded copper conductor FRLS-H PVC insulated and unsheathed, cable for 3/6 pin 15 Amp socket outlet controlled by one switch on independent board with and incl 2.5 sqmm green FRLS-H PVC insulated and unsheathed, copper conductor as continuous earth wire with lugs complete all as specified and directed (concealed type point wiring with terminal box).

S&F switch piano flush button AC 230 V Single pole 5/6 Amp one way complete all as specified and directed.

S&F socket outlet, non-shuttered, 2-in-1, 3 pin, 6 Amp AC 230 Volts flush type complete all as specified and directed.

S&F switch socket combination, 5 pin, 6 Amp AC 230 Volts flush type complete all as specified and directed.

S&F switch socket combination 2 in 1, 3 pin, 6 and 16 Amps flush type universal complete with all necessary electrical connection all as specified and directed.

S&F ceiling rose surface, polycarbonate/Bakelite, three terminals complete all as specified and directed.

S & F Modular Switch 1 way, 6 Amps, 1 module complete all as specified and directed.

S & F Modular Switch 1 way, 16 Amps, 1 module complete all as specified and directed.

S & F Modular Socket 6 Amps, 2/3 pin combined, 2 module complete all as specified and directed.

S & F Modular Socket 6/16 Amps, 2/3 pin combined, 2 module complete all as specified and directed.

S & F Modular Fan step regulator, 120 watt, 2 module complete all as specified and directed.

S&F Modular White cover plate with frame 3 module complete all as specified and directed.

S&F Modular White cover plate with frame 4 module complete all as specified and directed.

S&F Modular White cover plate with frame 6 module complete all as specified and directed.

S & F Modular type Metal Flush box 3 module complete all as specified and directed.

S & F Modular type Metal Flush box 4 module complete all as specified and directed.

S & F Modular type Metal Flush box 6 module complete all as specified and directed.

Supply and Hanging, ceiling fan, with brushless DC motor, 1200 mm sweep with remote, down rod, canopy, fan blades and accessories and connecting up including provision of PVC insulated, sheathed round flexible wire with multi stranded copper conductor of size 1.0 Sq mm, 3 core, 1100 Volts grade, from ceiling rose/ connector to fan, complete all as specified and directed. (MAKE : USHA, Model: ENERGIA 32 / CROMPTON GREAVES, Model : ENERGION HS / ORIENT, Model: ECOTECH / PANASONIC, Model: BLDC F-12XDA / HAVELLS, Model: Efficiencia Neo)

S&F exhaust fan 300 mm sweep, 900 RPM, heavy duty, AC Single Phase 230/240 volts, metal body, louvers complete with all accessories and connecting up with and including twin core twisted flexible copper conductor cable of size 1.5 sqmm (nominal area) from ceiling rose to fan complete all as specified and directed. (MAKE : HAVELLS, Model: Turbojet SP / CROMPTON, Model: EXHD300-6-1 / USHA, Model: Turbo Heavy Duty or equivalent model in BAJAJ / ORIENT)

S&F surface mounted LED luminaire, 1 X 20 Watt in aluminium housing, operating voltage 180-270 V, with Acrylic/ polycarbonate diffuser & integrated constant current electronic driver complete with all other accessories internally prewired and including connecting up with three core flexible copper wire of suitable size complete all as specified and directed. complying with the following specifications:- (a) minimum efficacy 110 lumen/watt (b) CRI not less than 80, (c) THD < 20% (c) having in built short circuit and surge protection (d) colour temperature not less than 5700 degree K (e) life not less than 25000 hours of operation

S&F recess mounted LED luminaire, of size 600 mm x 600 mm, in powder coated CRCA housing , having glare free diffuser, operating voltage 180-270V, with constant current electronic driver complete with all accessories with and including 35/36 Watt LED and including all accessories, mounting frame etc and connecting up with three core flexible copper conductor wire of adequate size complete all as specified and directed and complying with the following specifications:- (a) minimum efficacy 110 lumen/watt (b) CRI not less than 80, (c) THD < 20% (c) having in built short circuit and surge protection (d) colour temperature not less than 5700 degree K (e) life not less than 25000 hours of operation (f) Weather protection: IP20

S&F Double Door, Sheet Metal Enclosure for DBs (premium range), for mounting of MCB for 240 Volts, 8 way, with 100 Amps rated copper bus bar, Single Pole & Neutral, complete all as specified and directed. (MAKE : L&T, Cat No. DBSPN008DD / LEGRAND, Cat No: 507611 /ABB, Cat No. E-SHC M 8 / SCHNEIDER, Cat No. A9HSND08 / HAGER, Cat No: VYS08D)

S&F SPN DB, IP 43 protection, double door (Premium Quality), 240 volts, 4 way, with 100 Amps copper Bus Bar complete all as specified and directed. (MAKE : L&T, Cat No. DBSPN004DD / LEGRAND, Cat No: 507610 / ABB, Cat No. E-SHC M4 / SCHNEIDER, Cat No. NBKRENSNDD04 / HAGER, Cat No: VYS04D) NOTE FOR ITEM NO. 126 & 127:- (1) Incoming MCCB/RCCB/MCB and outgoing MCBs shall be measured and paid separately as "Supply Only". (2) Quoted rate is deemed to be inclusive of blanking plate for slots remaining blank after fixing of MCBs. (3) DB, MCCB, RCCB & MCB shall be of the same manufacturer.

S&F MCB (premium quality), 'C' series, SPN, 40 - 63 Amps, breaking capacity 10KA complete all as specified and directed. (MAKE : L&T / LEGRAND / SCHNEIDER / ABB / PANASONIC / HAGER)

S&F MCB (premium quality), 'C' series, SPN, 32 Amps, breaking capacity 10KA complete all as specified and directed. (MAKE : L&T / LEGRAND / SCHNEIDER / ABB / PANASONIC / HAGER)

S&F MCB (Premium Quality), 'C' series, single pole, 6 to 32 Amps, breaking capacity 10KA complete all as specified and directed. (MAKE : L&T / LEGRAND / SCHNEIDER / ABB / PANASONIC / HAGER)

Supply, installation, testing and commissioning of heater water storage type electric geyser (vertical cylindrical type) 25 ltrs capacity with BEE 5 star rating (min) and ABS body, glass lined/titanium enamel coated inner tank incl fixing arrangement with providing incl suitable capacity flexible cable 3 core with 3 pin plug of 16 amp complete all as specified and directed. (Make: RACOLD, Model - CDR DLX / AO SMITH, Model- HSE-VAS / Havells, Model: Monza Dx / BAJAJ, Model: CALDIA)

S&F sub main wiring with 2 runs of single core FRLSH PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 4.0 sqmm alongwith one run of FRLSH PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 4.0 sqmm as earth continuity conductor drawn through and incl PVC concealed conduit of suitable size complete all as specified and directed. (NOTE : Three runs of single core 4.0 sqmm cable & one run of PVC conduit shall be measured as one unit)

Supply, fixing, jointing and testing galvanised iron tube 25 mm bore, "medium grade" with all fitting laid in trenches or laid in floors complete all as specified and directed.

Supply and fixing gun metal gate or globe valve, with iron wheel head, screwed both ends for iron pipe and fixed for 25 mm bore pipe complete all as specified and directed.

M&L for drilling and tapping of Cast Iron Main (in position) for branch connections of the internal dia 40mm bore pipe, complete all as specified and directed.

S&F in repairs LED Street Light fitting 35/36 Watt capacity as mentioned under, in high pressure die cast aluminium housing with prismatic polycarbonate modular secondary lens optics with integrated constant current electronic driver, top opening driver cover, IP66 ingress protection, impact resistance of IK07 complete all as specified and directed and complying with the following specifications:-. (a) minimum system efficacy 120 lumen/watt (b) CRI not less than 70, (c) THD < 10% (d) Power Factor not less than 0.90 (e) having in built short circuit and surge protection upto 4 kV (f) having 10 KV external surge protection (for 45 watt & above) (g) colour temperature not less than 5700 degree K (h) life not less than 50000 hours of operation

S&F Bracket/Arm suitable for street light fittings, made out of 32 mm bore (light grade) GI pipe length not exceeding 1.5 metre long, fixed with 02 sets of flat iron clamp of size 25mm x 5 mm, with bolts, nuts and washers of suitable size including applying two coats of aluminium paint over a coat of red oxide zinc chrome primer incl taking down existing bracket complete all as specified and as directed by the Engr-in-Charge.

M&L for earthing complete with galvanized steel earth plate electrode 600 mm x 600 mm x 6.0 mm thick buried directly in ground vertically to a depth not less than 2.25 meter deep below ground level with top edge earth plate at a depth not less than 1.5M below normal ground level connected to galvanized steel earth wire 4 mm dia (upto 7.5 metres) by means of bolts, nuts check nuts and washers of galvanized steel and connected to main switch board or main control board as directed and including provision of concrete pit in PCC (1:3:6) type C1, pre-cast RCC (1:2:4) type B1 cover slab 45 cm x 45 cm x 5 cm reinforced with 8 mm dia. TMT bars @ 150 mm centre to centre both ways, with one handle for lifting made out of 8 mm dia MS bar, provision of funnel, wire mesh, 20 mm bore galvanized steel tubing (Medium grade) for watering, charcoal or coke and salt in alternate layers, 40 mm bore galvanized steel tubing medium grade for protection of earth lead connection, necessary excavation and earth work in any type of soil and including necessary testing complete all as shown in Figure 15A of IS 3043 :1987, complete all as specified and directed.

Supply, Laying, jointing and testing XLPE insulated, screened PVC bedded, galvanised steel strip or wire armoured electric power cable of size 10 Sqmm x 2 Core 1100 Volts grade with stranded aluminium conductor cable, laid in trench or fixed to wall/passing through pipe/pole incl necessary thimbles complete all as specified and directed.

MAZUMDER ENTERPRISE

ARJUN DAS VALECHA

RAJ ENTERPRISE

MS HORIZEN

dutta and dutta

UNIVERSAL TRADING CENTRE

DEB AND COMPANY