SPECIAL REPAIRS TO BLDG NO G-09 AND WORK AGAINST REVENUE WORK NO MTR/REV/01/2024-25 AT OD COMPLEX UNDER GE (EAST) MATHURA

Amount

S&F in repair steel rolling shutters, without ball bearing as specified including top cover, anchoring rod, hasp & staple, erected in position as indicated complete, gear operated type with chain wheel & hand chain thickness of laths 1.25 mm complete all as specified and directed.

Taking down cement plaster on brick or stone walls, concrete surface including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and as directed.

M&L for rendering 15 mm thick plaster on other than fair face of brick work or concrete surfaces in cement mortar 1:6 and finishing the surfaces even and smooth without using extra cement, complete all as specified and as directed.

M&L for rendering 10 mm thick on fair faces of brick work or concrete surface in cement mortar 1:6 finished even & fair complete all as specified and as directed.

M&L for preparation of newly plastered surface of walls providing 1mm thick wall care putty and applying two coats of distemper oil emulsion over and including a coat of alkali resitant primer complete all as specified and as directed.

M&L for preparation of new plastered or unplastered surfaces of wall including cornices, pilasters etc and applying two coats of cement base paint of approved colour on wall surface including all necessary arrangment for excution of work complete all as specified and directed.

M&L for complete removal of existing treatment from old plastered surfaces of walls and preparation of surface and applying two coats of distemper oil emulsion white or tinted on old walls surfaces complete all as specified and as directed.

M&L for complete removal of existing treatment from old plastered surface of walls, preparation of surface and applying two coat of cement based paint complete all as specified and as directed.

M&L for preparation of new steel surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamal paint over and including a coat of red oxide primer complete as specified and as directed.

Dismantling of plain or corrugated steel sheeting any gauge, thickness including reges hips, valleys etc completed as specified and as directed.

M&L Pre-painted galvalume aluminum zinc coating GI based semi-corrugated steel sheet AZ-150, thickness of 0.50mm of red colour having tensile strength of 550 Mpa as per IS 15965:2012 in roof covering/cladding to walls, fixed with self tapping screws complete all as specified and as directed.

M&L Pre-painted galvalume aluminum zinc coating GI based plain corrugated steel sheet AZ-150, thickness of 0.50 mm of required colour having tensile strength of 550 Mpa as per IS 15965: 2012 as in ridges, hips, valley gutters etc fixed with self tapping screws complete all as specified and as directed.

M&L for Mild steel work in tubular/hollow steel section trusses, purlins, vertical posts including special shaped washer, angle cleats, fish plates, gusset plates, base/bearing plates, flat iron, bolts and and nuts etc. complete using ERW or induction butt welded tubes conforming to 1161-1979 grade st 240 complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed.

Dismantling timber scantlings (framed work) exc 40 Sq cm in section in any position complete all as specified and as directed.

S&F in repair power coated aluminium (minimum thickness of powder coating 50 micron) frame work for doors, windows, ventilators and partition (fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other section of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gask etc. Aluminium sections shall be smooth, rust free straight, mirred and jointed mechanically wherever required including cleat, angle. Aluminium snap beading for glazing paneling C.P. brass/stainles steel screws, all as rectified and as complete.

M&L for Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening complete all as specified and as directed.

S&F in repair powder coated aluminium door shutters (thickness or powder coating shall not be less than 50 microns of approved colour) of aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, 3.0 Nos hinges, and tower bolt 200 mm long 02 Nos and one floor door stopper in each shutter, anodised aluminum snap beading screws etc. complete all as specified and as directed.

S&F in repair Powder coated aluminium (thickness of powder coating not less than 50 micron) window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised powder coated aluminium snap beading, screws, powder coated aluminium anodised fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified and as directed.

S&F 5.5mm thick, Sheet glass ordinary quality and glazing with aluminium beading exc 0.5 sqm in each pane complete all as specified and as directed.

S&F mild steel mortice lock, verticale type size 100 mm, 2 levers complete as specified and as directed.

S&F stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete as specified and as directed.

S&F 5.0 mm thick ACP sheet (aluminium composite sheet) fixed with aluminium beading in each pane complete as specified and as directed.

S&F in aluminium extruded section body Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg complete all as specified and as directed.

Dismantling of asbestos cement (corrugated semicurugated etc) sheets in roof covering including ridges, hips, valleys etc complete all as specified and as directed.

Demolition of Brick masory built in cement mortar including all quoins, arches, pillars etc Complete all as directed and as specified.

M&L for brick work with sub-class 'B' straight or curved on plan exc 6.0m mean radius built in cement and sand mortar 1:6 complete all as specified and as directed.

M&L for preparation of old painted steel surface of any description over 10 cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

M&L for cement concrete 1:2:4 type B1 (using 20 mm graded stone aggregate) as in coping, benching etc complete all as specified and as directed.

Demolition of cement concrete (unreinfored) in ground floors and pavings n.exc 15 cm thickness (below or above ground levels) complete all as specified and as directed.

M&L 75mm thick cement concrete 1:3:6 type C2 (using 40 mm graded crushed stone aggregate) as in plinth protection/ path laid in panel surface finished even and fair without using extra complete all as specified and as directed.

M&L for 4.0 mm thick Asbestos cement plain building boards, fixed to timber / MS framework including dismantling of old boards complete all as specified and as directed.

M&L for bitumen felt water proofing treatment using APP based polymeric membrane not less than 3.0 mm thick, weighing not less then 3.00 kg /Sqm, reinforeced with polyster non-woven fabric (weighing not less than 15 gm/Sqm) laid over and including cold bitumen primer applied at the rate of 0.30 kg/sqm by forced application including removal of bitumen felt complete all as specified and as directed.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L Machine cut kota stone slab flooring 20-25 mm thick laid over and including 20mm thick screed bed in cement mortar 1:6 and jointed with grey cement mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

M&L 15mm thick machine cut kota stone slab on vertical surfaces such as skirting, dados etc, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of Kota stone laid over 10mm thick rendering in CM 1:4 on fair faces of brick work or concrete surfaces finishing rough to receive stone, complete all as specified and as directed.

JWALA ELECTRIC CONTRACTORS (BID ID -3182432)

shyam construction (BID ID -3182555)

M/s KGN Builders (BID ID -3189155)

M/s Aditya Enterprises (BID ID -3188063)

KASHI NATH BANWARI LAL (BID ID -3183313)

KALPAARAV CONSTRUCTION (BID ID -3183384)

VANI CONSTRUCTION (BID ID -3182401)

BHARDWAJ CONSTRUCTIONS (BID ID -3181641)

M/s Himgiri construction (BID ID -3188491)