Loading…
Loading…
| # | Company | Amount |
|---|---|---|
| 1 | ₹61.0 L ACCEPTANCE OF TENDER CONDITIONS | ₹61.0 L |
Tender Value
₹75.6 L
EMD Value
₹75,635
Closing Date
20 Mar 2026, 11:00 amClosed
Construction of toilets block at CTU-06-01 and CTU-06-02 Circle-6 Jodhpur Mess Pandara Road New Delhi
NBCC/SBG/Redev-II/SN/2026/21
NBCC/SBG/Redev-II/SN/2026/21
Open Tender-Domestic
Civil Works General
New Delhi, Delhi
₹2,950
₹75,635
12 Mar 2026
12 Mar 2026
20 Mar 2026
20 Mar 2026
BILL OF QUANTITY
Name of Work- Construction of toilets block at CTU-06-01& CTU-06-02
Circle-6 Jodhpur Mess Pandara Road New Delhi” Under CSR Activity of
Sl.No. PARTICULARS Amount
1 Civil Works DSR 2023 60,64,097.00
2 Electrical Works DSR 2025 14,99,402.00
Digitally signed by AVDHESH
Name of Work- Construction of toilets block at CTU-06-01& CTU-06-02 Circle-6 Jodhpur Mess Pandara Road New Delhi” Under CSR Activity of NBCC.
BILL OF QUANTITY
DSR 2023 DSR RATE NDSR Rates
Sl. No Item UNIT TOTAL QTY DSR AMOUNT (Rs) NDSR Amount
Item No. (RS) (Rs.)
Excavation work by mechanical means (Hydraulic excavator)/ manual means in foundation
trenches or drains (not exceeding 1.5m in width or 10 sqm on plan), including dressing of sides
1 2.9 and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of
surplus excavated soils as directed, within a lead of 50 m.
Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in
2 2.25 layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and CUM
watering, lead up to 50 and for all lift.
2.1 2.25 Soil Filling upto plinth beam from NGL CUM 62.75 196.00 ₹ 12,298.78
Providing and laying in position cement concrete of specified grade
3 4.1 excluding the cost of centering and shuttering - All work up to plinth
1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone
aggregate 40 mm nominal size derived from natural sources)
Providing and laying in position ready mixed or site batched design mix cement concrete for
reinforced cement concrete work; using coarse aggregate and fine aggregate derived from
natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in
recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve
durability and workability without impairing strength; including pumping of concrete to site of
laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and
4 5.33 reinforcement as per direction of the engineer-in-charge; for the following grades of concrete.
Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be
payable separately. In case the cement content in design mix is more than 110% of the
specified minimum cement content, the contractor shall have discretion to either re-design the
mix or bear the cost of extra cement.
All works above plinth level upto floor V level
Concrete of M25 grade with minimum cement content of 330 kg /cum
Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position
5 5.22 and binding all complete upto plinth level.
5.1 5.22.6 Thermo-Mechanically Treated bars of grade Fe-500D or more. KG 5202.78 107.85 ₹ 5,61,120.31
Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in
6 6.4 superstructure above plinth level up to floor V level in all shapes and sizes in :
6.1 6.4.1 Cement mortar 1:4 (1 cement : 4 coarse sand) CUM 52.26 9344.35 ₹ 4,88,295.50
Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5
in superstructure above plinth level up to floor V level.
7.1 6.13.1 Cement mortar 1:3 (1 cement :3 coarse sand) SQM 218.00 1150.50 ₹ 2,50,809.00
Digitally signed by AVDHESH
DSR 2023 DSR RATE NDSR Rates
Sl. No Item UNIT TOTAL QTY DSR AMOUNT (Rs) NDSR Amount
Item No. (RS) (Rs.)
Extra for providing and placing in position 2 Nos 6 mm dia. M.S. bars at
8 6.15 every third course of half brick masonry. SQM 218.00 104.80 ₹ 22,846.40
15 mm cement plaster on rough side of single or half brick wall finished with a floating coat of
9 13.8 neat cement of mix :
10 5.9 Centering and shuttering including strutting, propping etc. and removal of form for
10.1 5.9.1 Foundations, footings, bases of columns, etc. for mass concrete SQM 34.00 392.15 ₹ 13,333.10
10.2 5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts SQM 100.00 961.30 ₹ 96,130.00
10.3 5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers SQM 238.00 736.40 ₹ 1,75,263.20
10.4 5.9.3 Suspended floors, roofs, landings, balconies and access platform SQM 183.00 927.25 ₹ 1,69,686.75
11 13.1 12 mm cement plaster of mix :
Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the
manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved
make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse
sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white
cement and matching pigments etc., complete.
12.1 11.41A.3 Glazed Vitrified tiles Matt/Antiskid finish of size
Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be
specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle
green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and
dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with
grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of
matching shade complete.
Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm
deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase
cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1
cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of
Engineer-in-charge and finished smooth.
14.1 8.10.1 White Agaria Marble Stone Nos 6 3500.45 ₹ 21,002.70
Digitally signed by AVDHESH
DSR 2023 DSR RATE NDSR Rates
Sl. No Item UNIT TOTAL QTY DSR AMOUNT (Rs) NDSR Amount
Item No. (RS) (Rs.)
Providing and fixing false ceiling at all height including providing and fixing of frame work made of
special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120
gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x
1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to
the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat
fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size
and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the
spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of
80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre,
shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made
out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels
0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed
to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @
230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with
the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a
flush finish of tapered and square edges of the board with recommended jointing compound ,
jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides
of joint and two coats of primer suitable for board, all as per manufacturer's specification and also
including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of
perimeter channels suitably fixed, all complete as per drawings, specification and direction of the
Engineer in Charge but excluding the cost of painting with :
12.5 mm thick tapered edge gypsum moisture resistant board
Finishing walls with textured exterior paint of required shade :
New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of
16.1 13.45.1 exterior primer applied @ 2.20kg/10 sqm SQM 318.00 223.60 ₹ 71,104.80
Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear
as well as curvilinear portions of the building all complete as per the architectural drawings with
18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4
17 11.55 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed
with pigment of matching shade including rubbing, curing and polishing etc. all complete as
specified and as directed by the Engineer-in-Charge :
Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.
Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates
etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and
fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with
necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required
size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of
Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be
considered excluding fixing accessories such as nuts, bolts, fasteners etc.).
Digitally signed by AVDHESH
DSR 2023 DSR RATE NDSR Rates
Sl. No Item UNIT TOTAL QTY DSR AMOUNT (Rs) NDSR Amount
Item No. (RS) (Rs.)
Providing and fixing carbon steel galvanised ( minimum coating 5 micron) dash fastener of 10
mm dia double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head, comprising of
10 mm dia polyamide PA 6 grade sleeve, including drilling of hole in frame , concrete/ masonry,
etc. as per direction of Engineer-in-charge.
Sub-Total (A) ₹ 44,35,062.70
Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-
decorative type, core of block board construction with frame of 1st class hard wood and well
matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on
both faces of shutters:
20.1 9.21.1 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws SQM 10 2392.65 ₹ 23,926.50
21 9.118 Providing and fixing to existing door frames.
30 mm thick factory made Polyvinyl Chloride (PVC) door shutter made of styles and rails of a
uPVC hollow section of size 60x30 mm and wall thickness 2 mm (± 0.2 mm), with inbuilt
decorative moulding edging on one side. The styles and rails mitred and joint at the corners by
means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and
stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of
size 25x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of 'H' section, a uPVC
21.1 9.118.2 hollow section of size 100x30 mm and 2 mm (± 0.2 mm) wall thickness fixed to the shutter styles SQM 46 3253.80 ₹ 1,49,674.80
by means of plastic/ galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC multi-
chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1
mm (± 0.1 mm) wall thickness . The panels filled vertically and tie bar at two places by inserting
horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per
manufacturer's specification and direction of Engineer-in-charge.
Providing and Fixing factory made PVC door frame made of PVC extruded sections of size 75
mm x 53 mm, having wall thickness 2.0 mm (± 0.2 mm). Both verticalssides of the frame
reinforced with PVC profile of cross section size 28 mm x 30 mm x 2 mm thickness (± 0.2 mm)
and 75 mm x 200 mm long, including reinforcing both ends of the top frame with PVC profile.
22 9.145 PVC Door Frame and PVC reinforcement profile to be mitred cut, jointed and fusion welded Meter 225 763.85 ₹ 1,71,866.25
together, including providing and fixing 3 nos of 125 mm long stainless steel hinges to frame,
fixing the frame with jamb with required nos & sizes of anchor dash fastener, all complete as per
manufacturer's specification and direction of engineer- in-charge.
Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought
23 9.1 framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length
(hold fast lugs or dash fastener shall be paid for separately).
23 9.1.1 Second class teak wood CUM 0.15 142949.70 ₹ 21,442.46
Providing and fixing aluminium handles of approved make anodized (anodic
24 9.100 coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required
colour or shade with necessry screws etc. complete.
Providing and fixing aluminium hanging floor door stopper ISI marked anodised
(anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed
to required colour and shade with necessary screws etc.
25.1 9.101.1 Single rubber stopper Each 2.00 39.60 ₹ 79.20
Sub-Total (B) ₹ 3,72,018.21
Digitally signed by AVDHESH
DSR 2023 DSR RATE NDSR Rates
Sl. No Item UNIT TOTAL QTY DSR AMOUNT (Rs) NDSR Amount
Item No. (RS) (Rs.)
Demolishing RCC work manually/by mechanical means including stacking of steel bars and CUM
26 15.3 disposal of unserviceable material within 50 meter lead as per direction of Engineer -in-charge 57.00 3551.25 ₹ 2,02,421.25
Demolishing BRICK work manually/by mechanical means including stacking of serviceable
27 15.7 material and disposal of unserviceable material within 50 meter lead as per direction of Engineer -
Sub-Total (C) ₹ 4,29,043.25
D.Sanitary& Plumbing
Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P.
28 17.7 brass waste of standard pattern, including painting of fittings and brackets, cutting and making
good the walls wherever require:
White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps
Providing and fixing vitreous china dual purpose closet suitable for use as squatting pan or
European type water closet (Anglo Indian W.C pan) with seat & lid fixed with C.P. brass hinges
and rubber buffers, 10 litre low level flushing cistern with fitting and brackets, 40 mm flush bend,
20 mm over flow pipe, with specials of standard make and mosquito proof coupling of approved
municipal design complete, including painting of fittings and brackets, cutting and making good
the walls and floors wherever required:
White vitreous china dual purpose WC pan with white solid plastic seat and lid with white vitreous
china flushing cistern and C.P. flush bend.
Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of
430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with
30 17.4 standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete,
including painting of fittings and brackets, cutting and making good the walls and floors wherever
30.1 17.4.1 One urinal basin with 5 litre white P.V.C. automatic flushing cistern Nos 6 6258.75 ₹ 37,552.50
Providing and fixing mirror of superior glass (of approved quality) and of required shape and size
31 17.32 with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :
Providing and fixing CP Brass 32 mm size Bottle Trap of approved quality & make Each 14 1034.80
and as per the direction of Engineer-in-charge.
Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. Each 32 349.15
33 17.16A triangular plate to Eureopean type W.C. of quality and make as approved ₹ 11,172.80
by Engineer - in - charge.
34 17.28 Providing and fixing P.V.C. waste pipe for sink or wash basin including
34.1 17.28.2 Flexible pipe
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for
hot & cold water supply, including all CPVC plain & brass threaded fittings and fixing the pipe with
clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent
35 18.8 cement and the cost of cutting chases and making good the same including testing of joints
complete as per direction of Engineer in Charge.
Concealed work, including cutting chases and making good the walls etc(inside
Digitally signed by AVDHESH
DSR 2023 DSR RATE NDSR Rates
Sl. No Item UNIT TOTAL QTY DSR AMOUNT (Rs) NDSR Amount
Item No. (RS) (Rs.)
Providing and fixing ball valve (brass) of approved quality, High or low pressure,
with plastic floats complete :
36.1 18.18.3 25mm i/d Brass Ball valves Each 2 464.05 ₹ 928.10
Providing and fixing gun metal gate valve with C.I. wheel of approved quality
(screwed end) :
38.0 MR Buy Back credit for old dismantled material including cartage and shifting. Lot 1 -27000.00 -₹ 27,000.00
Correction Factor of 0.973 on DSR-2023 Amounting to Rs.62,60,119.76 ₹ 60,91,096.52
Grand Total for Civil Works (DSR+NDSR) ₹ 60,64,097.00
Grand Total for Civil Works (DSR+NDSR) ₹ 60,64,097.00
Digitally signed by AVDHESH
Name of Work- Construction of toilets block at CTU-06-01& CTU-06-02 Circle-6 Jodhpur Mess Pandara Road New Delhi” Under
CSR Activity of NBCC.
Bill of Quantity
Electrical Works
SL NO 2025 ITEM DESCRIPTION UNIT QTY RATE AMOUNT
WIRING AND SUB MAINS
Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC
insulated copper conductor single core cable in surface / recessed heavy class Steel conduit, with
1 1.3.3 modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC Point 150.00 2101.00 ₹ 3,15,150.00
insulated copper conductor single core cable etc as required.a) Group C
1.5 Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core meter
2 cable in surface/ recessed Steel conduit alongwith 1 No 4 sq. mm FRLS PVC insulated copper 300 480.00 ₹ 1,44,000.00
conductor single core cable for loop earthing as required
1.7 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of
3 FRLS PVC insulated copper conductor, single core cable in surface/ recessed Steel conduit as
Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in
recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular
switch, connection etc. as required. (For light plugs to be used in non residential buildings).
1.32 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in Each
5 recess, including providing and fixing 6 pin 15/16 amps modular socket outlet and 15/16 amps 10 659.00 ₹ 6,590.00
modular switch, connection etc. as required.
1.24 Supplying and fixing of following modular switch/ socket outlet on the existing
Modular plate & switch including connection but excluding modular plate etc. as required.
6.2 1.24.4 3 pin 5/6 amp socket outlet Each 10 136 ₹ 1,360.00
6.4 1.24.5 6 pin 15/16 amp socket outlet Each 10 219 ₹ 2,190.00
Supplying and fixing following size/ modules, GI box Boxes alongwith modular base & cover plate
for modular switches in recess etc as required.
Digitally signed by AVDHESH
SL NO 2025 ITEM DESCRIPTION UNIT QTY RATE AMOUNT
1.26 Supplying and fixing of modular Blanking plate on the existing modular plate & Each
switch box excluding modular plate etc. as reqd.
1.21 Supplying and fixing of following sizes of heavy class PVC conduit along with
9 accessories in surface/recess including cutting the wall and making good the same in case of
recessed conduit as required.
2.3 Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240
volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar,
interconnections, powder painted including earthing etc. as required. (But without
MCB/RCCB/Isolator)
2.13 Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB
complete with connections, testing and commissioning etc. as required.
2.12 Supplying and fixing following rating, double pole, 240 V,isolator in the existing MCB DB complete
with connections, testing and commissioning etc. as required.
2.14 Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts, residual
current circuit breaker (RCCB), having a sensitivity current upto 30 milliamperes in the
existing MCB DB complete with connections, testing and
commissioning etc. as required.
2.10 Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker
14 suitable for inductive load of following poles in the existing MCB DB complete with
connections, testing and commissioning etc. as required.
2.11 Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. Each
Digitally signed by AVDHESH
SL NO 2025 ITEM DESCRIPTION UNIT QTY RATE AMOUNT
LED Panel light 2x2 ft. (System lumen efficacy ≥120 <135 lm/Watt) Supplying, Installation,
Testing & Commissioning of Panel light 2x2 ft., of following body material and construction as per
IS : 10322 with driver as per the requirement with Driver efficiency >85%, Operating voltage AC
140-270 Volt, frequency 50/60 hz, Operating temp range -5 °C to 40 °C, internal surge
protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, IP20, CRI ≥80,
UGR (Unified Glare Rating) <19, Flicker free, (flicker should be below 5 %), life time (LED, Driver &
electrical circuitry), of minimum 50000 Burning Hours
with , 70% of initial Lumen maintained till life ends, CCT 3000°K / 4000°K / 5700°K
/6500°K (As per ANSI Bin), DCM(Standard Deviation Color Matching) <3, Maximum power
consumption should not more than the specified rating and Fixture shall be of relevant BIS
standard. Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing.
complete in all respect i/c external connections with 1.5 sq mm FRLS/HFFR, PVC insulated
copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM
warranty. System lumen efficacy ≥120 <135 lm/Watt output .LM79 & LM80 Test report and all
testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as
approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of
aluminium housing such that LED junction temperature shall not rise above 90°C). Powder coated
die cast /Extruded aluminium Body (Thickness ≥ 1.20 mm)
Digitally signed by AVDHESH
SL NO 2025 ITEM DESCRIPTION UNIT QTY RATE AMOUNT
8.3 LED Down lighter (SMD Type) (System lumen efficacy >135lm/Watt) Supplying, Installation,
Testing & Commissioning of LED Recessed/surface Down lighter (Round /square/Rectangular)
SMD type of following body material with PMMA and prismatic diffuser and
construction as per IS : 10322 with driver as per the requirement with Driver efficiency >85%,
Operating voltage AC 140-270 Volt,
frequency 50/60 Hz, Operating temp range - 5 °C to 40 °C, internal surge protection of 2.5
KV with Short & Open circuit
protection ,THD < 10% , P. F.≥0.95, IP20, CRI ≥80, UGR (Unified
Glare Rating) < 19, Flicker free, (flicker should be below 5 %), life
time (LED, Driver & electrical circuitry), life time of minimum 50000 Burning Hours with 70% of
initial Lumen maintained till life ends as per LM80 extrapolation IES TM-21-11 report, CCT
3000°K/ 4000° K /5700°K / 6500°K (As per ANSI Bin), SDCM(Standard Deviation Color
Matching) <3, Maximum power consumption should not more than the specified rating and
Fixture shall be of relevant BIS standard. Manufactures Word Mark/ Name Engraved/ Embossing/
Screen printing on housing. complete in all respect i/c external
connections with 1.5 sq mm FRLS/HFFR, PVC insulated copper conductor single core cable
and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy >135
lm/Watt output. LM79 & LM80 Test report and all testing required for LED fixtures as per BIS
shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per
requirement. (Thermal management: heat sink of aluminium housing such that LED junction
temperature shall not rise above 90°C).
Digitally signed by AVDHESH
SL NO 2025 ITEM DESCRIPTION UNIT QTY RATE AMOUNT
8.9 LED LED Batten light (System lumen efficacy ≥105 <120 lm/Watt).Supplying, Installation, Testing &
Commissioning of LED surface mounted Batten light of following body material and construction as
per IS : 10322 with driver (Replaceable) as per the requirement with Driver efficiency >85%,
Operating voltage AC 140270 Volt, frequency 50/60 hz, Operating temp range -5 °C to 40 °C,
internal surge protection of 2.5 KV with Short & Open circuit protection, THD < 10%, P. F.≥0.95,
IP20, CRI ≥80, Flicker free, (flicker should be below 5 %), life time (LED, Driver & electrical
circuitry), of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life
ends, CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin), SDCM(Standard Deviation
Colour Matching) <3, Maximum power consumption should not more than the specified rating and
17 Fixture shall be of relevant BIS standard. Manufactures Word Mark/ Name Engraved/ Embossing/ ₹ 0.00
Screen printing on housing. complete in all respect i/c external connections with 1.5 sq mm
FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with
Minimum 5 year OEM warranty. System lumen efficacy ≥105 <120 lm/Watt output . LM79 & LM80
Test report and all testing required for LED fixtures as per BIS shall be submitted. Shape size
and CCT shall be as approved by Engineer-inCharge as per requirement. (Thermal management:
heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C).
Powder coated die cast /Extruded aluminium Body (Thickness ≥ 1.20 mm)
MR SITC of light fixtures suitable for LED fixture,10 W, 2ft Ceiling/Wall Surface mounted LED Linear Nos. 10.00
18 luminaire with system lumen output of not less than 1150 lm. Luminaire should be with IP20 879.84 ₹ 8,798.40
MR SITC of LED Bulkhead with a nominal system lumen output of 600 lumens and a minimum system Nos. 10.00
efficacy of 60 lm/W. The luminaire shall have a rated system lifetime of 50,000 burning hours at
L70. The luminaire should have a color temperature of 6500K and CRI > 70. The luminaire shall
19 meet IP66 rating and IK 09 rating with THD < 20% and PF > 0.9. The luminaire housing should 678.00 ₹ 6,780.00
made of High pressure die cast Aluminium with polycarbonate front diffuser. The total power
consumption should not exceed 10W (including driver).
MR SITC of heavy duty exhaust fans 450 mm exhaust fan 900 RPM min. complete with fan motor, Each 50.00
blades fixing frame, louver etc as required of havells makes or equivalent.
Total Electrical Works ₹ 14,99,402.00
Digitally signed by AVDHESH
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
21_NIT.pdf
Tender Document
21_BOQ.pdf
Tender Document
21_Drawings.pdf
Tender Document
21_List of Makes.pdf
Tender Document
21_SCC.pdf
Tender Document
21_Scope of work.pdf
Tender Document
GCC with amendment upto 17.pdf
Tender Document
Download all tender documents and submit your bid