Repair/Replacement to boundary wall fencing path hardstanding and other misc work and Repair/replacement to joinery plaster flooring, tiling internal water supply, false ceiling at certain associated work at sewar fort Bharatpur Mil Stn

Amount

M&L for Rendering 15 mm thick in CM (1:4) on stone masonry surfaces or surface other than fair face of brick-work or on one side of lathing finished even and smooth without using extra cement complete all as specified & as directed

Ditto all as per item no 1 but in CM (1:6) finished even and smooth without using extra cement complete all as specified & as directed

Taking down cement plaster of any description etc including racking out joints,hacking for key, scrubbing down with water all as specified & M&L for rendering 15 mm thick in CM (1:4) on stone masonry surfaces or surface other than fair face of brick-work or on one side of lathing upto 10 m height ,finished fair & even complete all as specified & as directed

Ditto as above item no 3 but in CM (1:6) finished even and smooth without using extra cement complete all as specified & as directed

Taking down cement plaster of any description etc including racking out joints,hacking for key, scrubbing down with water all as specified Including M&L for rendering 10mm thick in two layer (5+5)mm using premixed polymer modified cement plaster of approved make - Mix the powder with clean, drinkabie water in the ratio 5-7 liters of water to 20 kg of powder. Allow the mixture to stand for 10 minutes then mix again before applying. Best results are obtained with mechanical mixing, i.e. mixing drill and 20 liter bucket. When applying to non-porous surfaces and when extra durabillity an hardness is required add 1 liter of Acrybond chemical per 20 kg Polymer modified cement mortar. on Internal/External surface of brick work, reinforced cement concrete finished fair & even as manufacturer’s application instructions andcomplete all as specified and directed. Note:-(1) Before apply to concrete, cement render, brick and block surfaces that are clean and firm, free of dust, release agents, grease, wax, paint and other contaminants. Wet the substrate prior to the application of the mixture. (2) When applying more than one layer the preceding layer must be completely dry before applying the next

Taking down cement plaster of any description etc including racking out joints,hacking for key, scrubbing down with water all as specified & M&L for Rendering 5 mm thick in cement and sand mortar 1:3 on of cement concrete surfaces of ceiling of chajjas/roof protection etc including finishing the surface even and smooth without using extra cement complete all as specified and as directed

M & L Preparation of new plastered surface of wall including cornices, pilasters etc by brooming down and applying two coats of distemper oil emulsion white or tinted over a coat of alkali resistant wall primer with hand roller & 3 mm wall care putty (in Two Coats) complete all as specified and as directed

M&L Preparation of new plastered surfaces of walls or un plastered surface and applying two coats of cement base paint over a coat of alkali resistant primer with hand roller complete all as specified and as directed by Engr-in-Charge.

M&L Preparation of newly plastered surfaces of ceiling & applying three coats of white wash complete all as specified.

M&L Preparation of newly plastered surfaces of Wall & applying three coats of white wash complete all as specified.

M&L for Two coats of Apex Weather Proof Exterior emulsion (Water Based 100% Acrylic ) or approved equivalent grade paint using hand roller over one coat exterior grade wall primer on cement plaster,concrete ,exterior ceiling etc ,including surface to be painted shall made free from any loose paint ,dust,grease, fungus,algae, moss, shall got be removed .Color & Pattern /Color Combination of the paint shall got approved from Engineer In Charge.

Taking down chowkats or frames n. exc 1.5 sqm each with shutters (without taking off shutters from the frame).

Taking down chowkats or frames exc 1.5 sqm but n exc 4 sqm each with shutters (without taking off shutters from the frame)

Taking down shutter of any description area exc 1 sqm and n. exe 2 sqm

S&F for sollid PVC door frame of size 50mmx47mm made out of 5mm plain colour pvc sheet reinforced with m.s. squre tube complete all as specified and directed.

Supplying & fixing in the frames at site factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement all as specified and shown on serial SSR 2020 (Part-II) and Particular specification.

M&L for rolled mild steel framed work such as grill grating etc with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors , laddres, door gate frame, framed balusters, walk ways, railing , frame work of water tank and similar work conforming to Fe-290, Gde-E-165

S&F extruded aluminium alloy handle 150mm size fabricated type anodised, ISI marked .

S&F Aluminium anodised barrel tower bolt 150mm long of extruded section and fixed

S&F 75 mm butt hinges medium weight cold rolled mild steel, ISI marked, fixed to angle iron chowkats including welding complete.

S & F Factory made steel window with side hung shutteers including projecting type hinges with steel handle and steel peg stay complete with glazing bars dovetailed or welded Complete all as spcfd & as directed. (Note :- Mild steel wire cloth shall be measured and paid separately under respective items)

All as per item No 22 above but without glazing bars.

M&L dismantling floor,hearth or wall tiling including cement mortar bed(but not backing) , removing serviceable tiles to store and rubbish off the premises all as specified.

Providing and laying double charged vitrified floor tiles in 600X600mm sizes (thickness 8-10mm),in required combination of themes, with water absorption less than 0.08% and conforming to IS: 15622, of approved make, inany color and shades, laid on 15 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry including grouting the joints with white or coloured cement and matching pigments etc., complete all as specified and directed.

M&L Glazed ceramic Digital tiles ,matt/glossy finish in vertical surface,in required combination of themes, area of each tiles exceeding 0.09 sqm but not exceeding 0.27 sqm 7-8 mm thick set and jointed in neat cement slurry, over 15mm thick rendering in cement mortar (1:4) and pointed in white cement with pigment to match the colour of tiles complete all as specified.

M&L for Coloured Non skid ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.06 sqm bur not exceeding 0.16 sqm, over 10 mm thick screed bed in CM 1:4 in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match for repair & matched to existing floor tiles in patches.

M & L for Endura Designer Collection Series of Jhonson Tiles /Kajaria or somani tile of size 300x300x10 mm having with water absorption less than 0.5% and conforming to IS: 15622 of approved make in all colours and shades for outdoor floors such as footpath, court yard, multi modals location etc., laid on 15mm thick base of cement mortar 1:4 in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge.

M & L for Endura Designer Collection Series of Jhonson Tiles/ Kajaria or somani tile of size 400x400x10 mm having with water absorption less than 0.5% and conforming to IS: 15622 of approved make in all colours and shades for outdoor floors such as footpath, court yard, multi modals location etc., laid on 15mm thick base of cement mortar 1:4 in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge.

M&L for plain cement concrete type D2 1:4:8 (40 mm graded aggregate) as in foundations, filling and mass concrete.

Dismantling of stone slab and tiles of any description or thickness in floors, etc. laid dry & in pointed

M&L for Machine cut kota stone slab flooring 20-25 mm thick over cement screed 20 mm thick in cement mortar 1:6, laid and jointed with gray cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete.

M&L for Machine cut kota stone slab 20-25 mm thick in riser of steps, skirting, dedo and pillar laid over cement screed 15 mm thick in cement mortar 1:4, laid and jointed with gray cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete.

M & L Cutting, polishing existing Kota/ marble floor flooring,& verticle surfaces (three cuttings and mirror polishing) including Manson polishing, levelling certain places to Kota/ marble floor ,including necessary repair work & all necessary arrangments complete as directed By Engineer-in-Charge at site

Hacking out old broken glass any thickness, size, quality or description from wooden frames or stone, concrete or brick surrounds glazed with putty or fixed with beads including S&F 3 mm thick plain sheet glass ordinary quality in square not exceeding 0.5Sqm in each pane

M&L for Sheet glass ordinary quality 3 mm thick and glazing with oil putty in square n. exc 0.50 sqm in each pane.

S&F Galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.00 mm and fixed with tinned tacks, or galvanised wire staples.

S&F in repair bib tap, cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule of 15 mm bore complete all as spcfd & as directed

S&F in repair brass ball valve, high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrule and fixed of 20mm bore,complete all as spcfd & as directed

S&F in repair of pillar tap, cast copper alloy with capstan heads,chromium plated, fancy type screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks & fly nuts, screwed for iron pipes of 15mm bore including taking down old pillar tap.

S&F in Repair Sink made of stainless steel 1 mm thick Kitchen or Laboratory with plugs, washers and wastes; including beding in cement mortar on to dwarf walls or including fixing cantilever brackets and connecting union to waste pipe overall size 495mm x 420mm bowl size 410mm x 330 mmx160mm..

Dismantling of Stone Jali & Stone Pillar of any description , any thickness all as specified & as directed

M&L for 40 mm thick Sikandra stone jali decorative design of approved pattern by Eng-in-charge including all carving and moulding of corners fixed in cement mortar 1:4 to grooves of stone pillars application with colouring to match with colour of jali including fixing of stone jali for all corners & lift complete as per direction of Engineer in-charge.

S&F stone pillars(post) of size 100x100 mm including engraving decorative design of approved pattern on two face and dome shape approved by Eng-In-charge , height of each post as per sikandra stone jali, ,making groove on two face of size 43x5 mm for fixing of sikandra Jali in CM 1:4 complete as per direction of Engineer in-charge.

Dismantling of interlocking tiles of any description , any thickness

M&L 100 mm thick PCC 1:4:8 type D-2 using 40mm graded aggregate in foundation filling and mass concreate.

M&L Sand cusion under floor ,spreading and levelling in layers 25 mm thick .

M&L for 60mm thick & M-35 factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould/rubber molded, laid in required colour & pattern over 25mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge (cushion shall be measured & paid separately )

M&L PCC blocks or slabs 150 mm thick (1:2:4) mix type B-1 using 20 mm graded aggregated with plain or interlocking joints as directed complete in walls setting in CM (1:6).

Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded portion and making good disturbed ground post embedded in natural ground

Dismantling fencing wire mesh, any type

Excavating in post holes (or similar holes) each not exc 0.50 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers n.exc 25cm, watering, and removing surplus soil to a distance n.exc 50 m and making good surface in soft/ loose soil.

M/L Cement concrete in foundations filling and mass concrete Type C-2 1:3:6( 40 mm graded aggregates )

S&F MS work as in angle iron fencing post, fixed independently for fixing chain link fence, including all necessary cutting, drilling holes, bolting etc for screwing chain link fencing all as directed.

Supply only chain link fencing 4mm dia galvanized steel 50 mm x50mm mesh fixed to angle iron fencing post or angle frame complete all as directed.

Fixing only chain link fencing including line wires, any mesh size and type of standards rails straining bars etc incl perovision of binding wire.

S&F screw bolts (machine made) with hexagonal or square head at one head and rounded the other or screwed both end each screwed end to be fitted with washers and one hexagonal or square nut exc 05 cm nexc 10 cm long dia of shank 05 to 10 mm.

M&L for preparation of new untreated steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer.

Dismantling 1000 ltr water tank and M&L new 1000 ltr ISI marked rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position & including 20mm brass ball valve all as specified in SSR part-I

Dismantling 500 ltr water tank and M&L new 500 ltr ISI marked three layer rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position & including 20mm brass ball valve all as specified in ssr part-I

M&L for Asian Paints SmartCare Damp Proof fiber reinforced elastomeric liquid water proofing membrane applied over priming coat on newly plastered surface as per manufacturer instruction all as specified & as directed Note :-(1) For New masonry surfaces must be allowed to cure completely. It is recommended to allow 28 days as the curing time for new masonry surfaces. (2) Surface should be free from any loose paint, dust or grease. Remove all existing paints coatings completely. It is recommended to use Intense wire brushing, High speed water jet and vaccum cleaner for thorough cleaning of the surface to avoid “Peeling off” problem (3) For filling cracks upto 3mm use Asian Paints Crack Seal. Bigger cracks, damaged portions and hollow areas must be repaired with polymer modified cement mortars. Application (1) Apply SELF PRIMING Coat of Damp Proof Ultra Fibre reinforced liquid layer In ration of 3:1 of (Used water as thinner ) @5.5 Sqm/L & allow to Dry for 4-6 Hours (2) Apply Three Neat Coat of Damp Proof Ultra Fibre reinforced liquid layer without dilution by brush or roller at a time interval 4-6 Hours of Priming Coat

Demolition of brick masonry built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facings,dressed stone work and precast concrete articles as spd and directed by Engr-in-Charge.

M&L Brick work with sub class 'B' old size bricks bricks straight or cured on plan exceeding 6 m mean radius built in cement mortar 1:6

Ditto Item No 11 but except bricks

S&F 35 mm thick 2nd class hardwood( hollock ) factory made plain framed, panelled shutters (any No. of panels) with lock rail and panel of 9mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on both faces size of members as per IS 1003 PtI

S&F 35 mm thick 2nd class hardwood ( hollock ) factory made glazed and skeleton shutters open rebated and prepared to receive glass, gauge etc.( without sash bars ), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, gauge etc., sizes of members of shutters as specified in SSR Part I.

S&F MS holdfast, hook and pintle hinges, large hasp and staples, clamps, hooks for hanging fans and similar small articles conforming to Fe-290 Gde E-165 including necessary welding etc. and fixed in position.

S&F 100 mm butt hinges medium weight cold rolled mild steel, ISI marked, fixed to angle iron chowkats including welding complete.

S&F 150 mm long mild steel barrel tower bolts stove enameled black with bright bolt (ISI marked)

Mild steel pressed steel bow handle oval type stove enameled black of size 150 mm (ISI marked)

S&F MS sliding door bolt, plate type, 300mm long, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts & nuts, 4 on bolt plate and 2 on staple plate and fixed.

M&L for coloured Glazed ceramic tiles in vertical surfaces of size 300mm x 200mm, 7mm thick over and including 15 mm thick rendering in CM 1:4 , set and jointed in neat cement slurry and pointed in white or coloured cement to match all as directed.

M & L for full body vitrified step tiles & risers of Jhonson endura Tiles series ,Kajaria or somani tile of 12-15mm thickness for existing size of tread & risers having with water absorption less than 0.05% aalong with bull nosing ,anti skid,high fleaxural strength properties of approved make in all shades and shades in forstairs of multi modals location etc., laid on 15mm thick base of cement mortar 1:4 in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge.

Providing and fixing 20 mm thick gang saw cut, mirror polished, premoulded and prepolished,Granite of any colour and shade machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. rubbing, cutting, moulding and polishing to edges to give high gloss finish etc. complete at all levels.

M&L for fixing of sunroof stone (of approved quality) (As per existing size length x width 600 to 750 and thikness 50-75 mm) by replacing damaged stone chajja, wherever required as per approvedg design, including cost of dismantling/ making of wall/ parapet where chajja is inserted/fixed following existing design & construction details. Item includes cost of material ,dismantling the existing chajjas ,safety measures/ use of specified equipments for workers of building required to complete the work at all heights & including all leads complete all as specified & directed

Dismantling wrought iron or mild steel work of any description not otherwise provided for

Dismantling Asbestos cement (plain or corrugated, etc) sheets in roof coverings.

M & L for Pre- painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as spfd & directed.

M & L prepration of new wood or wood based surface of any description over 10 cm widtgh or girth and applying two coats of synthetic enamel paint over a coat of pink primer.

M&L for one coat painting with synthetic enamel paint to old wood or wood based surfaces of any description, not otherwise described over 10 CM width or girth including preparation of surface including all preparatory work complete all as specified.

M&L for one coat painting with synthetic enamel paint to old steel or steel based surfaces of any description, not otherwise described over 10 CM width or girth including preparation of surface including all preparatory work complete all as specified

Demolition of PCC in roof covering, kerbs, roof kerbs, benching, coved fillets etc including old decayed water proofing treatment of any type all as specified & as directed (also including the rate for disposal of building rubbish/ malba of dismantled or waste material collected after demolition of existing treatment & dumping for lead upto 1km for all lifts)

M&L for 40mm thick pcc type -B-1 (1:2:4) using 20mm graded stone aggregate in roof covering , benching , etc & finished even and rough all as per directed complete all as specified & directed

M&L for screed bed or bedding layer of 15 mm thick in cement mortar 1:4, for roof surfaces even & smooth without using extra cement complete all as specified & directed (mixed with WPC & paid seprately)

M&L for Preparing surface for roof treatment by removing all loose gravel ,dirt ,oil & foreign matter by jet of dry air and clean the surfaces mechanically or by grinding to make it smooth before application ,provide 75X75mm coving made out of PMC mortar as above on all joints of vertical up stands to ensure does not exceed 5% immediately before application of liquid membrane material incorporation & protection to be provided ,applying fibre reinforced elastomeric liquid water proofing membrane with resilient acrylic polymers having Sun Reflectivity Index (SRI) of 105 on top of concrete roof in three coats @10.76 litre/ 10 sqm with 1st coat appllied in water ratio (ratio elastomeric liquid water proofing membrane :water will be 3:1) as primer, after the 1st coat is completly dry becomes slightly darker than apply 2nd coat with undiluted elastomeric water proofing liquid in criss -cross direction with roller .spread glass fibre mesh reinforcement of 1mm thickness with overlap of 50mm in both direction when the surface is still tacky . After the drying of of 2nd coat completly apply the final coat of undiluted elastomeric water proofing liquid in a direction parpendicular to previous coat .the min. thickness of dry film of complete application should not be less than the as recommanded by manufacture. the overall dry thickness should not be in any case less than 1.5mm complete all as specified & as directed.

S&F in repair Brass Chromium plated central hole basin including mixer with fixed spout complete all specified. (Make;- Kerovit Catologue No :KB711026 or equivalent in Jaquar / parryware .)

M&L for PVC connection 15 mm size with PTMT nuts of length 600 mm

S&F for in repair Brass Chromium plated long body Bib cock with wall flange complete all specified. (Make;- ESSCO cat part no APR 105107 oror equivalent in Jaquar ,perryware)

S&F for in repair Brass Chromium plated Angular stop cock with wall flange complete all specified. (Make;- ESSCO cat part no APR 101053 or or equivalent in Jaquar ,parryware)

S&F in repair Single piece-WC with UF Soft Close Slim Seat Cover, Fixing Accessories, Accessories set and Cistern Fittings, Size: 370x670x720 mm, S Trap-220mm complete all as specifies (Make;- Jaquar Registered design LYS-WHT-38851S220UFSMN or equivalent in Hindware ,perryware)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. 91.01 25 mm bore

20 mm bore

S&F in repair viterous china Table Top Basin with CP waste coupling, Size: 500x420x120mm complete all as specifies (Make;- Jaquar Registered design FLS-WHT-5935 or equivalent in Hindware ,perryware

Providing and fixing in repair white vitreous china Large ISI Urinal SIze of 382x398x601 mm (Make Kerovit Catologue No :Rasso (isi) Model No-KS507 or equiv. )and sizes respectively with with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required

S&F in repair for PVC wall panelling with panel of 300 mm x 6 mm Hollow section of Sintex pattern SPUF- 146 or equivalent , fixed with PVC plug and screw and inserted to next panel groove, edges and corners of all door/ window/openings etc to be covered with PVC angel fixed with solvent cement complete all as specified as manufacturer's Instructions

Supply and fixing in repair anodized snap grid frame work of size 605mm x 605 mm for false ceiling including necessary notching. The snap grid shall consist of anodized aluminium main & cross tee of size 36.5 x 25 x 1.4 mm weighing 0.24 Kg/RM and 23.5 x 26.4 x 1.40 mm weighing 0.191 Kg/RM respectively. The main and cross tee shall be jointed at junction crossing with anodized aluminum angle bracket of size 15mm x 15mm x 1.5 mm weighing 0.12 Kg/RM fixed with suitable MS bolts, nuts and washer. The snap grid (main/cross tee section) shall be supported at ends all along the wall with anodized aluminum angle of size 40 x 25 x 2 mm weighing 0.36 Kg/RM fixed to wall with suitable arrangement and providing 12 mm thick mineral fibre board of make Armstrong and fixed in grid complete all as specified and as directed by Engineer-in-Charge.

S & F Hangers 6 mm dia GI (upto 1200 mm length) adjusting level fixed to roof slab by means of ceiling cleats made out of GI flat 40 x 3mm Size 60mm long and expnsion hold fasteners 12.5 mm dia 40 mm long complete all as specified and directed .

Supply only water proofing compound ISI marked

S & F Rooled mild steel work as in post roof trusses (Framed), trussed purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee angle, channel or flat sections, ms pipe) including distance pieces, cleats etc, conforming to Fe-410W Gde E-250 quality 'A' Complete all as specified and directed.

M/S MAMTA CONSTRUCTIONS

abhinav and company

B R ENTERPRISES

VASUNDHARA AND COMPANY

M/s Ranaji Construction Co

PD GUPTA AND COMPANY

Pioneer Enterprises

krishna Associate