SPL REPAIR TO BLDG NO P-365 (FILTERATION PLANT) AND SPL REPAIR TO BLDG NO P-364 (CLEAR WATER PUMP HOUSE) AT INS SHIVAJI LONAVLA

Amount

Removal of old filter media and pebbles from filter bed of filtration plant and depositing within 50 m distance for diposal all as directed.

Cleaning of Inner Surface of Both Filtration Chamber of size 5x3x2.5 m by removing sticky particles from walls, floor by scraping with sand paper till all the surfaces are totally cleaned the solution of hydrogen peroxide in the ratio 1:100 can be utilised for cleaning the surfaces. applying one coat of white wash finally prior to load the filter media all as directed.

M & L for laying fresh supporting quartzs gravels size varing from 10mm to 15mm in filter beds all as shown and directed by engr-in-charge.

All as per item No.03 above but of size 20mm to 25mm quartzs.

All as per item No.03 above but of size 30mm to 35mm quartzs.

All as per item No.03 above 40mm to 50mm quartzs.

Supply & laying fresh fine sand over the final layer of pebble all as shown and directed by engr-in-charge.

Taking out sluice valve of size 150 mm dia refacing regrinding and refixing back to its location all as specifed and directed

Removal of mud and other unwanted materials from settling tank of filtration plant and depositing within 50 m distance for disposal all as directed.

Cleaning of inner surface of settling tank of filteration plant size of 100000 gln by removing sticky particles from walls, floor by scraping with sand paper till all the surfaces are totally cleaned the solution of hydrogen peroxide in the ratio 1:100 can be utilised for cleaning the surfaces.

Cleaning of inner surface of clear water channel of filteration plant by removing sticky particles from walls, floor by scraping with sand paper till all the surfaces are totally cleaned the solution of hydrogen pero-oxide in the ratio 1:100 can be utilised for cleaning the surfaces.

M&L for complete removal of old existing paint and apply two coats of acrylic amulsion base premium quality mat finish exterior anti-fungal paint over a coat of primer.

S&F GI tubing medium grade with all new connection , fitting laid in trenches including reducing the length of required size and making to good surfaces of road , path , culvert drainage etc of size 50MM bore GI pipe.

All as per item No.13 above but 40MM bore

S&F butterfly valve for GI pipe of 50mm size all as specified and directed.

S&F non return butterfly valve 50mm size all as specified and directed.

S&F gun metal globe gate valve with iron wheel head screwed both ends for iron pipe of 50mm size.

All as per item No.17 above but 40MM bore

S&F Bends (any type, radius and angle) tapers any type, (straight, bend, increasing, decreasing or double socket etc.) tee pieces single branch. "Y" junction, double branch, cross (all sockets or socket and spigot) collars, caps and plugs which suits 250 to 350 mm bore dia all as directed by engr-in- charge.

Dismantling existing defective air compressor unit of capacity 15 HP for repairs and taking out unserviceable baffle plate- 03 Nos, bearing- 02 Nos , shaft - 01 No and replacement of the same by provinding new components as per existing size and shape for smooth functioning of air compressor all as directed by engr-in- charge.

Dismantling existing defective electric motor of air compressor of capacity 15 HP 3 phase 415 volt AC supply including disconnection of electrical connectioin , opening up lectric motor , taking out urnt out winding coils from stator body , cleaning of slots by using soft wire brush / petrol wash to remove unwanted material and rewing of electric motor by using super enamelled copper wire as per existing size and gauge , heat and varnishing and repalcement of bearing make SKF reassembling the motor after repairs carried out and fitted its original its position all as directed at site.

S&F in replacement of existing steel rod with CI wheel for smooth operation of existing inlet, outlet and wash out valves with firm foundation including servicing of gear and connected items by dismantle and fixing back all as directed at site.

Supply, Installation, testing and Commissioning of 350 mm dia, single phase, Motor Actuated Butterfly valve with disc material of CI with nylon coating, hand wheel for manual operation and having 02 nos. limit switches for Open / Close condition and valve position indicator. Input Voltage: 230 V, A.C. Designed line pressure: 16 kg/sq cm. In built CPU:- Quad-core 64-bit ARM Cortex A53 clocked at 1.2 GHz Inbuilt 4 USB 2 ports In built Base Ethernet Port In built Micro SD port for loading your operating system and storing data In built wireless LAN and Bluetooth Low Energy Extension between butterfly & acuator :- 15 Feet The mounting shall be indirect type using specialized extended type arrangement of GI pipe of suitable size/thickness complete all as specified and directed. Make : UNIVERSAL SWITCH GEAR CONTROL /EMERSON/ROTORK/SD TORK

Supply, Installation, testing and Commissioning of 250 mm dia, single phase, Motor Actuated Butterfly valve with disc material of CI with nylon coating, hand wheel for manual operation and having 02 nos. limit switches for Open / Close condition and valve position indicator. Input Voltage: 230 V, A.C. Designed line pressure: 16 kg/sq cm. In built CPU:- Quad-core 64-bit ARM Cortex A53 clocked at 1.2 GHz Inbuilt 4 USB 2 ports In built Base Ethernet Port In built Micro SD port for loading your operating system and storing data In built wireless LAN and Bluetooth Low Energy Extension between butterfly & acuator :- 15 Feet The mounting shall be indirect type using specialized extended type arrangement of GI pipe of suitable size/thickness, so that actuator mounting is at least 36 inches above ground level complete all as specified and directed. Make : UNIVERSAL SWITCH GEAR CONTROL /EMERSON/ROTORK/SD TORK

Taking down old corroded GI pipe of any size

Taking down defective sluice valve iron GI/CI pipe line of 350MM dia size.

All as per item No.26 above but 250 mm dia CI sluice valves.

Supply, Installing,Testing and Commissioning of Ultrasonic Level Transmitter at Sump and overhead tank for measurement of level with following specification:- Range : 0-6 meters Accuracy : 0.5 % minimum Supply Voltage : 24V DC Output : 4-20 mA , 0-10V DC Make: Pepperl+ Fuchs / Nivelco / Siemens/Banner

Supply, fabricate, errect, connecting, testing & commisioning LT Panel, Indoor Type, weather and vermin proof made out of 2 mm thick CRCA sheet with front opening and locking arrangement, epoxy powder coated having colour siemens grey, 200 Amps capacity aluminium bus bar for phase, 3 No's and 1 No 200 Amp bus bar for neutral, mounted on epoxy insulator including neccessary copper control wiring, heat shrinkable, RYB coloured sleeves over bus bar for identification, earth shields, circular holes at bottom / top to receive incoming and outgoing cable, cable lugs, cable gland of sizes as required floor mounting angle iron frame made out mild steel angle iron of size 40 x 40 x 6 mm grouted on PCC (1:3:6) upto required height suitable for the following control/ fitments sensible for 3 phase, 50 Hz, 415 V system complete with and including following :- INCOMING- (a)Thermal magnetic adjustable FP MCCB of capacity 125 A 35 kA- 1 No. OUT GOINGS- (b) Thermal magnetic adjustable FP MCCB of capacity 63 A 25 kA - 1 No (c) Thermal magnetic adjustable FP MCCB of capacity 32 A 25 kA - 1 Nos (d) Multidigital Meter :- 3 No's (e) Indicating lamp LED type :- 3 sets (f) Star Delta Fully automatic ML 2 Starter :- 04 No's

Taking down old unserviceable chlorination unit and supply install testing and commissioning of direct cylinder mounted type vaccum chlorinator for pressure feed including all gauges, pumps motors conforming to IS 10553 part 2 having capacity 1 to 1000 gm/hr including injector and connectec accessories complete all as specified and directed.

Supply and fix LED street light fitting 70 W, 230 V AC out door type with high pressure die cast aluminium housing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete.

Taking down old unserviceable pump and Supply and fix centrifugal monblock pumpset of capacity 1 hp head range 06 to 12 meter single phase flow rate 120 to 414 LPM working under 220 V including all fittings all as specified and directed.

Cleaning of inner surface of under ground clear water pump house sump size of 150000 gln by removing sticky particles from walls, floor by scraping with sand paper till all the surfaces are totally cleaned the solution of hydrogen pero-oxide in the ratio 1:100 can be utilised for cleaning the surfaces all as specified and directed.

S&F Air Valves with dual air outlets, conforming to IS 14845 of size 80 mm dia bore and fixing up in water supply mains all as required and directed by Engineer in charge.

Taking down defective sluice valve iron GI/CI pipe line of 150mm size.

M&L for run lead joint suitable for spigot & socket pipes and fittings for 300 mm bore.

All as per item No.36 but of 200 mm.

Taking down defective Air valve GI/CI pipe line of any size.

Taking down old corroded CI/MS pipe of any size

Taking down defective Air valve CI/CI pipe line of any size

Supply, Installation, Testing, Commissioning 1 KVA UPS / INVERTER with Sealed Lead Acid Maintenanace free Batteries for powering the panel for a minimum of 30 minutes in case of supply failure. UPS should have following features:Charger:- Build in solid state three stage recharge. Display:- LED Display Audible Alarm:- Main Failure Alarm, Battery Low Alarm, UPS Warning, Fault. (Make: APC / TATA LIEBERT / NUMERIC)

Supply, Installation, Testing, Commissioning and Programming of Bi Directional Parabolic antenna with control station to generate strong directional effect with WLAN network support having mast mounting arrangment. Control station should operate on license free frequency with necessary hardware at a suitable location to be connected to the central scada server so as to establish connectivity with every station of the network after conducting a frequency survey of the entire area of interest and identify suitable locations to mount the station hardware and the height of the antennas to establish clear line of sight either directly or by multi hop so as to be able to send data. Antenna type:- Omni and Bi Directional Parabolic antenna Gain:- as per site requirement Degree of protection:- IP65, seawater-resistant, Material:- Lexan EXL 9330 (Antenna housing), V2A (Bracket), V2A (Mast clip), Mounting type:- Mast mounting The should have a approval of Wi-Fi compliance, Environmentally Friendly Use Period :- UNLIMITED = EFUP-e Note:-Rate quoted is deemed to be included for making arrangemets of accessories such as mounting bracket and mast clips Make:- Siemens / Schneider Electric / Universal Switch Gear Control / ABB Automation

Updating existing PC based master control station. The scope includes:Services for programming, configuration and customisation of the Smart Station Platform with respect to the Water supply Module as per actual site conditions and requirement of the engineer (a). Landing Page to depict criritcal paramters viz. - Level of water in all tanks, pump status ON/OFF/FAIL and Water Quality parameters (b). Creation of drop down tabs to monitor the all Pump houses and Remote PLC Panel systems individually (c). Creation of individual PLC Panel wise schematics and layouts for the Water Supply system as per the actual site including display of all relevant parameters viz. Water level, Pump ON/OFF/FAIL status, Valve OPEN/CLOSE/FAIL status(d). Soft keys for remote manual operation of all pumps and motorised valves from the Master Control station. (e). Creation of Day wise Reports for : (i) Run hours of pumps (ii) Pump / valve operation faliures (iii) Active/Return status of Each equipment with date and time. (iv). Configuring notifications, alerts and alarms as per preset logic. (v) Consumption Patterns - Daily, Weekly, Monthly and Annually. Note: The existing SCADA software must not be tampered / affected in any way while carrying out these changes. Note : The already installed SCADA Software is installed and programmed by M/S Universal Switch Gear Control. It is Commanded that the updating of SCADA system should be done through OEM(i.e. M/S Universal Switch Gear Control) or through the authorized service provider of the OEM

Supply, Installation, Testing and Commissioning of 4 pair CAT 6 UTP cable for Sensors . Make : D Link/ Finolex/ Polycab

Supply only 2 Core 1.5 sq. mm PVC sheathed PVC insulated copper armoured cable. Make: Havells/Polycab/Gloster

Supply only 6 Core 1.5sq.mm. PVC sheathed PVC insulated copper armoured cable. Make: Havells/Polycab/Gloster

LT Panel indoor type weather vermin proof made out of 2mm thick CRCA sheet with front opening and lockng arrangement epoxy powder coated hving color siemens grey 800 Amps capacity aluminium bus bar for neutral mounted on epoxy insultor including necessary copper control wiring heat shrinkable RYB colored sleeves over bus bar for identification earth shields circular holes at bottom /top to receive incoming and outgoingcable cable lug cable gland of sizes as required floor mounting angle iron flame made out mild steel angle iron size 40x40x mm grouted on PCC (1:3:6) upto requred suitable for the following control fitments sensible for 03 phase 0 Hz 41 V system complete with and including following : Incoming: a) Thermal magnetic adjstable FP MCCB of capacity 800 A 36 KA -01 b) Thermal magnetic adjustable FP MCCB of capacity 200 A 2 KA 03 Nos c) Thermal magnetic adjustable FP MCCB of capacity 100 A 25 KA -6 Nos d) VAF meter -1 Set h) Indicating lamp LED type -1 Sets

Dismantling of existing corroded MS flanged pipe 300 mm dia including all fittings flanges old nuts bolts etc all as specified and as directed.

M&L for 300 mm MS Flange (heavy duty) including rubber gasket packing suitable nuts, bolts, washers all fittings like brackets of any angle, short pices, welding the flanges to MS pipe complete.

M & L for disconnecting carefully and dismantling the pump set from motor unit and opening complete pump set, cleaning replacing of unserviceable parts such as gun metal bushes, rubber packing, MS Nut, Bolts, rubber coupling (spider), Air valve and worn out parts etc and reassembling, re-installing commissioning and testing for satisfactory running complete all as specified and as directed for Centrifugal Multistage pump set of Discharge 9 Lps & Head 210 Mtr connected to 50 HP Motor capacity of pump. Note :- Spare parts replaced shall be measured and paid separately as "Supply only". Cost of transportation, loading and unloading for to and from of pump set to worshop and back is included in quoted rates.

M & L for overhauling of motor unit, 3 phase, 415 volts by dismantling and opening completely, cleaning internal parts thoroughly, replacing unserviceable minor parts like nut bolts, washers, terminal plate, cable lugs, greasing including insulating materials, varnishing, heating, reassembling reinstalling and testing complete all as specified and as directed for the Motor of Centrifugal pump set of 50 HP capacity of motor.Note:- Unit rate quoted shall be deemed to include for minor unserviceable parts as mentioned/ required for repairs. All other major spares as specified hereinafter will be measured and paid separately as "Supply only". Cost of transportation for to and fro of motor set to worshop and back is included in quoted rates.

Supply and fix LED street light fitting 200 W, 230 V AC out door type with high pressure die cast aluminium housing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete.

Dismantling floor, hearth or wall tilling including cement mortor bedding (but not backing), removing serviceble tiles to store and rubbish off the premises complte all as specified.

M&L for rendering 10mm thick in CM 1:4 as in backing coat of as in skirting and glazed tiles in walls.

M&L for Glazed Coloured ceramic tiles in vertical surfaces 300X600 mm set and jointed in neat cement slurry and pointed in white or coloured cement to match.

M&L for chequered cement conc tiles 20 cm X 20 cm X 20 mm thick, set jointed and painted with grey cement and pigment to match the shade of tile over & including 20 mm thick screed bed bedding layer of morter in CM (1:6)

Surface excavation n.exc (not exceeding) 45cm deep and averaging 30cm deep and getting out in hard rock

Surface dressing n exc 15 cm deep in hard dense soil

M&L for 100 mm thcik Cement concrete type B- 2, 1:2:4 (40mm graded aggregate)

M&L Brick work with sub class 'B' bricks straight or curved on plan exc 6 M mean radius in CM 1:6

M&L for preparation of old surfaces of wall and applying two coats of oil bound distemper complete all as specified and as directed.

M&L for Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shad (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over old wall surfaces including preparation of old wall surfaces

M&L for Preparation of new surface of steel and applying two coats of synthetic enamel paint over a coat of red oxide primer

M&L for preparation of old plastered surfaces of walls, pillars, cornices etc by brooming down with steel wire burshing, scraping down smoke shoot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of white wash on ceiling surfaces complete all as specified and directed.

Taking down chowkats or frames N.exc 1.5 Sqcm with shutter (without taking of shutter from the frame.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing

S&F for 35 mm Factory made Moulded door shutter consisting of solid core single leaf flush door of 30 mm thickness,lipped with 15 mm (5mm x 3) thick x30 mm width on the other stiles & bottom rails & 10mm (5mm x 2) thick x 30 mm width on other stiles & bottom rails , The inner panel laminated with 2 mm thick termite proof, water proof and fire resistant molded PVC sheet with 2,4,6 raised panel designs in different plain and / or prelam colours after routing the Moulded design on one side & 2 mm plain and / or prelam PVC sheet on other side using rubber adhesive on flush door & solvent cement adhesive on the PVC Lipping and manufacturer's specification & drawing etc, complete all as specified and directed.

S&F 250 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed

S&F 100 mm thick Butt hinges, medium weight, cold rolled mild steel, and fixed

S&F Aluminium bow handles, cast type, anodised 150 mm long

S&F 200 mm long Aluminium, anodised, barrel tower bolts of extruded section and fixed

S&F framed work such as ornamental/intricated design gate including printed hings using Fi, Angle iron, square bars, MS plain sheet, grills, gratings etc. with ends of bars ladders, framed balusters, walk ways, railings, frame work of riveted or forged into spilkes, framed guard bars, barred iron doors,souldered and/or water tanks and similar work complete all as specified and directed by Engr-in-charge.

S&F 1 mm thick Steel rolling shutters, with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete; gear operated type with bevel gear box and crank handle

M&L for 40mm thick Cement concrete type B-1, 1:2:4 (20mm graded aggregate) as in floor

S&F Cast iron work grade FG 150, unmachineed, in brackets, gully traps, gratings, railings, frames, manhole covers, fire and soot doors, dampers, stop valve boxes, gate stops, parts of ranges, balusters and similar articles exc 5 kg each

Shree Ayyappa Engineering