PROVN OF DRAIN INSIDE 269 MED REGT, GUARD ROOM AT CALEB VIHAR COMPLEX AND TOILET BLOCK FOR ACP NO 03 AT GN PATH AGE B/R-II AT GE JHANSI

Amount

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in any type of soil complete all as specified and directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, laying of under ground cable/GI pile line or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in any type of soil complete all as specified and directed.

Excavation over areas not exc. 4.5m deep in any type of soil and getting out, complete all as specified and directed.

Returning, filling in, including leveling, watering and well ramming in layers not exc 25 cm complete all as specified and directed by Engineer-in-Charge.

Removing excavated material not exc 50m and depositing where directed at a level not exc 1.5m above the starting point complete all as specified and directed by Engineer-in-Charge.

M&l for PCC 1:4:8 type D2 using 40mm graded stone aggregate as in foundations fillings & mass concrete complete all as specified and directed.

M/L providing RCC (Design Mix) M-25 ( using 20 mm graeded aggregate as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete

M/L providing RCC (Design Mix) M-25 ( using 20 mm graeded aggregate as in Columns, pillars, piers, posts and struts

M/L providing RCC (Design Mix) M-25 ( using 20 mm graeded aggregate as in Beams, cantilevers, bressummers, lintels over 1.5m span

M/L providing RCC (Design Mix) M-25 ( using 20 mm graeded aggregate as in Chajjas

M/L providing RCC (Design Mix) M-25 ( using 20 mm graeded aggregate as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like

Earth filling under floor, incl spreading, leveeling, watering and well ramming in layers n exc 25 cmm in soft/loose soil complete all as spd and directed

Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering

Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface

M/L for 75 mm thick PCC 1:4:8 type D2 using 40 mm graded stone aggreagate as in sub base of flooring complete all as directed.

M/L for 25 mm thick cement concrete 1:2:4 Type B0 using 12.5 mm graded stone aggreagate as in flooring.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter

Formwork to sides of pillars, posts, struts, piers, columns and stanchions

Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping)

M&L for brick work with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius, built in CM 1:6.

Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4

Mild steel TMT bars 5mm dia and over upto and including 10mm dia as in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips

Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips

M&L 15mm thick rendering on fair faces of brick or concrete surfaces in CM 1:4 finished even and smooth without using extra cement.

M&L 15mm thick rendering other than fair faces of brick or concrete surfaces in CM 1:6 finished even and smooth without using extra cement.

M&L 5mm thick rendering in CM 1:3 on ceiling of concrete surface finished even and fair etc. complete all as specified and directed

M&L 10mm thick rendering in CM 1:3 on fair faces of concrete surface finished even and fair mixed with WPC @ 3% by wt of cement, used on roof , chhjja complete all as specified and directed. Note : Water proofing compound shall be inclusive of quoted rate.

M/L for cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth .

M/L for joint free non skid ceramic coloured tiles, of size 600x600x7 to 8 mm thick (square/rectangular) , in floors etc , set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM (1:6) complete all as specified and as directed by the Engineer -in-charge.

M/L for non skid ceramic color tiles of size 400x400x7 to 8 mm thick ( square / rectangular) as in flooring etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed/ bedding layer in CM (1:6)

M/L for glazed ceramic coloured tiles ( with concept highlighter ) of size 300x 450x 7 to 8 mm thick on vertical surface such as in dado over and including 10 mm thick rendering in CM (1:4) complete all as specified and directed.

M&L for non skid colour ceramic tile 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or colour cement to match over and including screed bed or bedding layer of 15 mm thick, in CM 1:6.

S&F vitreous China Urinal, Half stall type, white (excluding flushing cistern, flush pipe and waste pipe)

S & F viterous china squantting pan Orissa pattern size 580 x 440 mm white with 'P' or 'S' trap front or back inlet and feet rest WC's ( excluding flushing cistern and flush pipe) including provision of cement concrete bedding and making good surfaces complete all as directed. as specified.

S/F PVC low level flushing cistern 10 lts capacity with ball valve float and handle ,syphonic action type including brackets and flush pipe of polythelene of low or high density or PVC 32 mm dia low level flushing cistern all as specified and directed.

S&F vitreous china wash hand basin ,white, flat back, size 550x400 mm including chain and plug and porcelain stopper, brackets including cutting for and pinning in ends of brackets or erecting stand

Supply and fix PVC connection 15 mm size with PTMT nuts of length 450 mm long.

S/F tubular towel rail 20 mm dia 600 mm long brass CP including brackets fixed to wall complete all as directed.

S&F bib taps, 15 mm dia chromium plated, screwed down, screwed for iron pipe or for brass ferrule and fixed .

S&F 15 mm dia pillar taps, cast copper alloy, with capstan heads, chromium plated fancy type screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed.

S&F brass chromium plated shower rose 125mm size

S/F 15 mm stop cock of chromium plated fancy type copper alloy screwed down high pressure for iron pipe or for unions fixed.

S&F 15mm bore concealed stop cock CP type with long shank and cup screwed down high pressure with crutch or butterfly handle screwed for iron pope or union complete all as specifed and directed

S&F for 15 mm bore angle cock CP fancy type with long shank and cup screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed all as specified and directed

S&F PVC flexible waste pipe suitable for wash hand basin

Supply and fix urinal spreader of PTMT any color for fixing with 15 mm dia pipe (Min weight 60 gms)

S&F 32 mm bore waste coupling of PTMT (half of full thread) (Min weight 45 gms each)

S/F chromium plated grating doom 100 mm dia

S&F grating square 150 mm size of PTMT (Minimum weight 100 gms)

S&F of rotational moulded polyethylene cylindrical vertical with closed top water storage tank triple layered WHITE COLOUR 1000 Ltr capacity with connecting nipple, hoisted and fixed in position on new or existing foundation and making GI tubing inlet or outlet connection, complete all as specified and directed.

S&F tubes `medium grade' galvanised with all fittings and fixed complete to walls and ceiling or laid in floors 20mm bore.

S&F tubes `medium grade' galvanised with all fittings and fixed complete to walls and ceiling or laid in floors 15mm bore.

S&F 20 mm dia gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed

S & F 20 mm Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. Minimum weight 15mm-142gms/ 2 0 m m - 2 1 0 g m s . /25mm-455gms/ 40mm - 690 gms)

S/F Flush pipe of polyethylene of low or high density or PVC. 32 mm dia, for low level cistern

S/F 75 mm PVC SWR pipe single socketed in any length with rubber ring joints laid in trenches or in floors .

S/F 110 mm PVC SWR pipe single socketed in any length with rubber ring joints laid in trenches or in floors .

S/f 75 mm dia PVC (SWR) bends any radius

S/f 110 mm dia PVC (SWR) bends any radius

S&F 75mm bore branch pieces, single (equal or ;unequal) ordinary or inverted (spigot or socket type) or with parallel branches with access door all as directed

S/f 125/110 mm PVC (SWR) gully trap, setting and jointing with solvent cement

S/F PVC nahani trap 75 mm dia with grating including jointing to waste pipe fixed in cement concrete 1:2:4 type B1 complete all as directed.

M&L for 150x150 mm dia salt glazed stoneware gully trap, square or round mounted, type "P" as specified.

S/ F Stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof.

S/F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, in opening as per specification & drawing .

S/F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S&F factory made shutter 35 mm thick plain framed panelled shutters (any No of panels) of 2nd class HW (Sal/Bajasal/ Banteak) with panels of timber flat on both side medium density wood particle board with commercial face veneers ISI marked kiln seasoned chemically pressure treated etc complete all as specified and directed

S/f for 35 mm thick 2nd class hard wood glazed and skelton shutters as in Doors open rebated and prepare to receive glass , gauze etc (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) complete all as directed.

S/F MS Butt hinges 100 mm sizes medium weight cold rolled mild steel fixed as in door chowkhats .

S/F 100 mm Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21

S/f 150 mm aluminium handle cast type anodized complete all as directed.

S/F Aluminium anodised, barrel tower bolts of extruded section of length 150 mm and fixed with cadimium plated wood series, complete all as specified and directed.

S/F mild steel 300 mm sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate complete all as specified and directed.

S/f of box type steel window with 82x40x1.25 m MS tubular frame with side hung shutters ( double shutter for glass and gauze) without sash bars jointed together with and incl grill using 12 mm square bar @ 10 cm C/C incl box type hinges with steel handle and steel pag stay complete glazing bars doveled and welded complete all as specified as directed. Note:- The Glass / gauze shell be measured and paid seperately.

S/f of box type steel ventilator with 82x40x1.25 m MS tubular frame partly gauged with top hung shutters incl grill using 12 mm square bar @ 10 cm C/C incl box type hinges with steel handle and steel pag stay complete glazing bars doveled and welded complete all as specified as directed. Note:- The Glass / gauze shell be measured and paid seperately.

S/F 3 mm thick sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and directed.

S/F 3 mm thick pin headed glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and directed.

S/F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.18mm complete all as specified and directed.

M&L for mild steel section as in door/windows chowkhats frame of steel gate of grade Fe-410-0 or Fe-310-0 including all necessary machine wks i.e. cutting, welding, grinding etc, complete all as specified and directed.

M/L for preparing new surfaces of wood or wood based materials of any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as directed.

M/L for preparing new surfaces of steel of any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide primer complete all as directed.

M&L for preparing new plastered surface of wall and applying two coats of weather proof exterior grade emulsion paint over and including a coat of cement based primer, complete all as specified and directed.

M&L for preparing newly plastered surfaces of wall and applying two coats of oil bound distemper over coat of putty to make the surface to be plain and smooth complete all as specified and directed

M&L for preparing newly plastered surfaces of ceiling and applying two coats of oil bound distemper over coat of putty to make the surface to be plain and smooth complete all as specified and directed

M&L for preparation of new plastered surface of wall and applying three coats of white wash complete all as specified and as directed.

M&L for preparation of new plastered surface of ceiling and applying three coats of white wash complete all as specified and as directed.

M&L water proofing treatment to roof slab with APP based modified polymeric membrane centre core 100 microne HMHDPE outer flim 20 micron each having thickness 3 mm weight not less than 3kg/Sqm with 100mm overlap laid as per manuacturer's instructions and complete all as specified and as directed by Engineer-in-Charge with following course of description below:- (a) 1st coat applying bitumen primer confirming to IS-3384-1965 @ 0.40 Kg/Sqm to be applied on prepared roof surface till the surface is properly impregnated (b) 2nd coat of bonding material using blown type bitumen conforming to IS-702 of grade 85/25 @ 1.20 Kg/Sqm (c) 3rd course ie. laying of APP Based modified membrane described herein before with 100mm overlap in longitudinal direction and 150mm in transverse direction, all joints and changes in all direction should be covered covered with cement mortar (1:3) mixed with SBR latex @ 200ml per bag of cement and cured well before laying the membrane.

M&L for applying one coat of bituminious aluminium paint @ 0.20 Kg Per Sqm over APP membrane, complete all as specified and directed.

M&L for screed bed 15mm thick fair finished using cement mortar (1:4) with WPC on flat roof slab

M&L 75 mm thick cement concrete type C2 1:3:6 in path for finished even and smooth without using extra cement including forming joints and filling with bituminous filler material.

M&L for Chequered cement concrete tiles with grey cement and pigments 20cm x 20cm x 25mm thick, set, jointed and pointed in near cement slurry in floors over and including 15 mm thick screed bed in CM (1:6) complete all as specified and as directed by the Engineer -in-charge.

Construction of Septic tanks, exc, in ordinary soil, foundation In PCC 1:2:4, brick work in CM 1:4, RCC Slab covers including RCC precast manhole cover having 6mm plate embedded all around/fibre reinforced cover with angle iron frame Vent shaft and sludge chambers etc., complete for 50 users all as specified and shown in drawing No CEBZ/TD/76/2011 Sheet 1/2 & 2/2. Note :- 1. The Reinforcement shall be used 10 mm dia 150 mm c/c in main bar and distribution bars. 2. The cost of all kind of earth work, brick masonry work, plastering, coping, RCC slab, reinforcement, form work etc is deemed to be included in quoted rate only.

Construction of Soakage wells exc, in ordinary Soil, Foundation in PCC 1:3:6, wells of Honey combed and solid in M-25 Concrete, including intercepting chamber, screen chamber Brick work in CM, RCC cover slab in M-25/ RR masonry / Filling with brick bats, complete of size 3.00 M dia X 3.0M deep.(Refer and read TD drg No CEBZ/TD/78/ 2011 Sheet No 1/2 and 2/2

M&L Providing, cement concrete type B0, 1:2:4 (using 12.5 mm graded aggregates) in roof kerbs or mud stops, rounded or chamfered on edges, in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed

M&L providing precast cement concrete for manhole cover slabs and similar work type B-1 (1:2:4) using 20mm graded aggregate set in cement mortar (1:4) all as specified.

M&L for providing 450mm dia reinforced cement concrete pipes class NP2 with one colllar per length of pipe complete all as sped and directed

M&L 40 mm thick Damp proof course in cement concrete type Bo 1:2:4 to horizontal or vertical surfaces including necessary formwork mixed with water proofing compound @ 3% by wt of cement. Note : Water proofing compound shall be inclusive of quoted rate.

M&L concrete bed to drain pipe for 150 mm dia pipes in PCC (1:4:8) type D2 using 40 mm graded stone aggregate incl packing under and haunching against the sides of pipes after they are laid and tested including provision of 150 mm salt glazed stone ware drain pipes grade A ISI marked laid in trenches and jointed as specified

M&L for Point wiring with 1.5 Sqmm FRLS insulated, unsheathed, multistranded, 1100 Volts grade copper conductor cable single core conforming to IS:694 along with one run of 1.5 Sqmm FRLS insulated copper conductor cable green in colour for continuous earthing drawn through and including medium grade rigid PVC conduit conforming to IS:9537 (Pt-III) and its all accessories/junction boxes/ inspection covers etc of suitable size but not less than 20mm concealed in wall/ floor etc including provision of pressed steel terminal box of thickness not less than 18 SWG, with earth dolly of suitable size concealed in wall and covered with 3 mm thick phenolic laminated hylam sheet fixed with brass /GI screws for mounting switches, sockets, fan regulator, etc. complete all as specified and directed by Engineer-in-Charge for the following points:- Make For Conduit : -AKG/ Atul/ Kalinga/Precision/Modi ; Make For Wire : Havells/ Polycab/ Finolex /RPG / V-GUARD /KEI

One light point controlled by one switch

One Exhaust fan point controlled by one switch.

One ceiling fan controlled by one switch and one regulator

One 6A socket point controlled by one switch on independent board

One 6A socket point controlled by one switch on same board

All as per srl item No. 102 here-in-before but with 2.5 sq mm FRLS copper wire with 2.5 Sqmm FRLS copper earth wire for one 16 Amp socket point controlled by one 16 Amp switch on independent board.

Notes for item No. 102.00 to 103.00 (i) Quoted rate shall deemed to incude the cost of cutting chases on wall/floor for concealed conduit wiring and making good with cement plaster, putty and paint to match with the existing surface. (ii) If any beam / column / Rock wall is encountered while cutting chases, that particular portion may be provided with PVC casing & caping or surface conduit for drawing cables and surface PVC gang box fully enclosed type for mounting switches, sockets & regulators etc to avoid any damage to the structure. (iii) No cutting shall be done on ceiling for laying PVC conduit for ceiling fan point wiring. Surface conduit or PVC casing caping may be used in that portion.

S&F, Switch piano type, single pole, one way, 6 amps, 240 volts, complete all as specified and directed. Make :Havells(Reo) /Goldmedal /SSK /GM

S&F, Socket, two-in-one, 5 pin, 6 Amp, universal type, 240 volts, complete all as specified and directed. Make :Havells(Reo) /Goldmedal /SSK /GM

S&F, Switch piano type, single pole, one way, 16 amps, 240 volts, complete all as specified and directed. Make :Havells(Reo) /Goldmedal /SSK /GM

S&F, Socket, 6 pin, 6/16 Amp, multipurpose 240 volts, complete all as specified and directed. Make :Havells(Reo) /Goldmedal /SSK /GM Modular

S&F, angle holder, metal cased, bakelite body, 240 volts, complete all as specified and directed. Make :Havells(Reo) /Goldmedal /SSK /GM

Supply and fix electronic fan regulator in 5 steps, 240V, 50Hz complete all as specified and directed. Make :Havells(Reo) /Goldmedal /SSK /GM

S&F, Ceiling rose, three terminals, bakelite body, 240 volts, complete all as specified and directed . Make :Havells(Reo) /Goldmedal /SSK /GM

S & F 7 W White LED retrofit lamp suitable for B-22 holder base with polycarbonate diffuser and aluminium heat sink. Make: Havells / Bajaj / Wipro / Philips /Osram

Supply and fix LED batten box type with CRCA sheet steel body pre-wired suitable for and including provision of 1x20/22Watt (4 feet) retrofit LED tube with PC body and connecting up with twisted three core flexible copper wire of 0.5sqmm white colour from ceiling rose to connector of fitting complete all as specified and directed by Engineer-in-Charge.Make: Havells / Bajaj / Wipro / Philips /Osram

Supply and fix LED batten 9W/10W (2 Feet) complete with polycarbonate diffuser and built in with electronic driver including connecting up with twin core twisted flexible copper conductor cable form ceiling rose to connector of fitting complete all as specified and directed by Engineer-in-Charge. Make: Havells / Bajaj / Wipro / Philips /Osram

Supply and fix LED building security light fitting 25 watts with high efficiency long life LEDs with In-built electronic driver complete housed in pressure die-cast aluminium housing covered with polycarbonate cover with IP66 degree of protection including GI pipe bracket made up of 25mm dia medium grade GI pipe of length 1.50m bent to required shape and fixing on walls with suitable MS clamps(02Nos) made up of 25mmx5mm MS flat, nuts, bolts and washers and provision of 3 core twisted flexible copper cable 0.5 sqmm white colour from ceiling rose to connector of fitting complete all as specified and as directed by Engineer-in-Charge. Make: Havells / Bajaj / Wipro / Philips /Osram

S&F, in replacement of bulk head light fitting including 5W retrofit LED lamp and making all electric connections complete all as directed. .Make: Havells / Bajaj / Wipro / Philips /Osram

Supply and fix MCB distribution board, TPN, 4 way 415 Volt in sheet steel powder painted enclosure double door type with IP 43 degree of protection with built in copper bus bar, neutral link and earth link complete including cutting the wall surfaces for flush mounting of DB and making good with cement plaster, putty and paint to match with the existing surface all as specified and directed by Engineer-in-Charge. Note: MCBs shall be measured and paid separetely. Make : Indo Asian / L&T / Havells

S& F MCB TPN 63 Amp, 10 KA, 'C' curve, 430 V, 50 Hz Make : Indo Asian / L&T / Havells

All as per srl item No. 118 here-in-before but SPN 32 Amp 230 Volt. Make : Indo Asian / L&T / Havells

All as per srl item No. 118 here-in-before but 6 to 32 Amp, Single Pole 230 Volt. Make : Indo Asian / L&T / Havells

Supply and laying or fixing or passing through pipe, 1100 volts grade heavy duty cable with XLPE insulated stranded aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or strip and overall PVC sheathed, 16 sq mm 4 core in service connections as per IS 7098(Part 1) including connecting on LT OH line / LT panel /DB with suitable lugs, glands, binding wire etc including taking down existing service cable of any description complete all as specified and directed. Make: Havells /Polycab /Univarsal/Gloster/Asian Cable/RPG

All as per item No 121 here in before but size of cable 10 Sqmm 2 core.

Material and labour for Double wall corrugated HDPE pipe, ISI marked of outer dia 50mm, inner dia 38mm with smooth internal and profiled external surface, non-pressure laid in trenches/floors/duct or fixed on walls /pole including all connections, accessories like socket, couplers, bends, etc for protection of LT cable XLPE grade 1100 volts complete all as specified and directed by Engineer-in-Charge. Make: Finolex / Kisan / Prince / Tirupati /Supreme / Jain Irrigation Sys

M&L for Earthing complete with galvanised iron earth plate electrode 600mm x 600mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtrs deep below ground level) with top edge of the plate not less than 1.5 mtrs below normal ground level connecting to GI wire 4 mm dia as earthing lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel and earth wire protected by 15mm dia GI pipe medium grade and connected to distribution board/earthing test point all as shown in electircal plate No. 3 of SSR Part-I(2009) and testing on completion complete all as specified and directed. Note :- The unit rate quoted shall also include for excavation, earth work in any type of soil, charcoal and salt plain cement concrete 1:3:6 mix, Type C1 pit, 40mm thick RCC 1:2:4 mix type B1 cover reinforced with 8mm dia TMT bras @ 150mm C/C both ways, GI funnel with watering pipe, wire mesh,protection pipe, earth wire upto 7.50m long complete in addition to item No. 1(a) to (e) of preamble (Notes) under sub heading earthing, specified in SSR Part II.

Supply and fix ceiling fan, 1200mm sweep, 3 blade, white colour, energy efficient, 50W / 52W power cosumption, with minimum 310 RPM, 100% copper winding motor with and including down rod, canopy (02 Nos), GI fan clamp with rubber bush, GI nuts, bolts and split pins etc (without regulator) and connecting up with 3 core x 0.5 sqmm flexible copper conductor cable from ceiling rose to connector of fan complete all as specified and directed by Engineeer-in-Charge. Make: Crompton / Khaithan/ Usha / Bajaj

S&F of exhaust fan of 300 mm sweep size with 04 Nos blade leafs, 70 W power consumption, 1300 to 1400 RPM, 100 % copper winding, heavy duty type, double ball bearing complete with and incl self closing MS louvers, mounted in suitable opening arrangement and suitable for operation on 230 volts single phase, 50 Hz, AC supply and fixed by using 4 Nos 50 mm long MS fasteners, nuts, bolts & washers and making all electric connection with three core PVC insulated, PVC sheathed copper conductor flexible cable of 0.5 Sqmm size, complete all as specified and directed. Note : 1. The cost of making hole in the existing wall and making good the disturbed surface of wall/ ceiling etc as required is deemed to be included in the quoted rate. 2. Make : Orient / CG / Bjaja / Usha / Almonard.

Supply install and testing of evaporative desert coller having nominal air flow capacity of 3000 Cum per hour with metalic body made out of 22 swg GI sheet alongwith front grill and three side shutters, colling pads etc and body fitted with heavy duty fan motor, copper wound, 1/7 HP, 1360/1400 RMP, three speed control, single phase, 230V, 50Hz with 450mm fan blades and 18 Watt submersible pump complete with float valve, PVC distribution pipe, control switch complete suitable for desert coller connecting cord PVC insulated and PVC sheathed copper conductor cable 3 core, 1.5 Sqmm conforming to IS:694 up to 2.5 mtrs long fitted with mounted plug top 3 pin 6 Amps ISI marked complete all as specified and as directed by Engr-in-Charge. Make of Cooler Kit and Pump : CG Power / Khaitan / Marathon Electric. Make of wire : Havells / Polycab / KEI / Gloster. Make of Plug Top : Anchor / SSK / Havells / GM.

M&L for GI water tubing 25 mm dia nominal bore, medium grade, ISI marked, with and including all fittings i.e. bend, tee, elbow, reduce, union etc, laid in trenches, complete as specified and directed. Make : Jindal / TATA / Prakash Surya / Zenit Note : 1. The excavation & earthwork shall be measured & paid for separately. 2. The cost of all type of GI fitting i.e. bend, tee, elbow, reduce, union etc is deemed to be included in quoted rates.

S&F of Gun metal globe or Gate valves with ironwheel head, screwed both ends for iron pipe of 25 mm dia bore, complete all as specified and directed. Make - Zoloto / Leader / Neta / Sant Valves

Cutting and screwing of existing steel tubing for alterations or additions of size 40 or 50 mm done in position without taking down and inserting tee branch connection, complete all specified and directed. (Each cut measured).

M/S RAJ CONSTRUCTION AND ELECTRICAL

m/s ramesh saran agarwal

mahavir engineers and contractors

M/s JS Constructions