Modernization or Raze and Rebuild of Retail Outlet with facilities at Ms Veteran Co Pvt. Ltd, District- Purba Medinipur, State -West Bengal under Haldia Divisional Office, West Bengal State Office

RAZE AND REBUILD VETERAN CO (OPM)

Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including takin g out and disposal of excavated earth within site and lift upto 1.5 m, disposed soil to be levelled and neatly dressed as directed b y Engineer-in-charge. Extra for levelling & neatly dressing of disposed soil completely to be paid separately as per item no. MPLCN0 0600.

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30 cm in depth, 1.5m in widt h as well as 10 sqm on plan) including taking out and disposal of excavated earth within or outside site to unobjectionable place a nd lift upto 1.5m, as directed by Engineer-in-charge. Disposed earth to be levelled and neatly dressed. Extra for levelling & neatly dressing of disposed soil completely to be paid separately as per item no. MPLCN00600

i) All kinds of Soil

ii) Ordinary rock

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1. 5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excav ated soil & disposal of surplus excavated soil as directed, within or outside the site at an unobjectionable place.

i) All kinds of Soil

ii) Ordinary rock

Extra for every additional lift of 1.5m or part thereof in excavation or banking excavated or stacked materials in all kinds of soil

Extra for every additional lift of 1.5m or part thereof in excavation or banking excavated or stacked materials in ordinary or hard rock

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in de pth, consolidating each deposited layer by ramming and watering, within premises and lift upto 1.5m

Supply & filling of local earth (including royalty) by mechanical transport also including ramming & watering of the earth in layers not exceeding 20cm in depth in plot, trenches, plinth, sides of foundations etc. complete

Supplying and filling in plinth with sand within specified grading zone of fine aggregates specified in table 3.1, clause 3.1.3 of a ttached specifications under floors, etc. in layers not exceeding 20cm in depth, each deposited layer to be compacted by ramming inc luding watering, consolidating and dressing complete.

i) Local Fine Sand within grading zone IV

i) Distance upto 1 km

i) Distance upto 1 km

Providing and laying in position cement concrete of specified grade excluding cost of centering & shuttering. All work up to plinth level:

iii) 1:2:4(1 Cement : 2 Coarse Sand :4 Graded stone aggregate of 20mm)

v) 1:3:6(1 Cement : 3 Coarse Sand : 6 Graded stone aggregate of 20mm)

viii) 1:4:8(1 Cement :4 Coarse Sand :8 Graded stone aggregate of 40mm)

Centering and shuttering including strutting, propping etc. and removal of form work for:

i) Foundations,footings,bases of column

Providing & fixing at or near ground level PRECAST CEMENT CONCRETE in kerbs, edgings etc. as per approved pattern and setting in pos ition with cement mortar 1:3 (1 Cement:3 coarse sand) including the cost of required centering, shuttering complete. 1:1.5:3 (1 Ceme nt : 1.5 Coarse sand : 3 graded stone aggregate 20mm nominal size)

Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12 .5mm nominal size). Item includes providing & mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer's specifications. Providing & applying a coat of residual petroleum bitumen of grade VG-10 of approved quality usi ng 1.7kg per square metre on damp proof course after cleaning the surface with brushes & finally with a piece of cloth lightly soake d in kerosene oil

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level

ii) RCC 1 Cement :1½ Coarse Sand: 3 Graded Stone Aggregate 20mm

iii) RCC 1 Cement :2 Coarse Sand: 4 Graded Stone Aggregate 20mm

Providing & Laying Reinforced cement concrete work in walls (Any thickness) including attached pilasters, buttresses, plinth an d string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level UP TO FLOOR V LEVEL excludin g cost of centering, shuttering, finishing and reinforcement :

ii) RCC 1 Cement :1½ Coarse Sand: 3 Graded Stone Aggregate 20mm

Providing and laying RCC work in vertical and horizontal fins individually or forming box louvers, facias and eaves boards above pli nth level up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement with 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20mm nominal size).

Centering and shuttering including strutting, propping etc. and removal of form for :

i) Foundations,footings,bases of columns, etc. for mass concrete

ii) Walls (any thickness) including attached pilasters, buttress, plinth and string courses etc.

iii) Suspended floors,roofs,landings,balconies, access platform and Shelves (Cast in situ)

iv) Lintels, beams plinth beams,girders bressumers and cantilevers

v) Columns, Pillars, Piers, Abutments, Posts and Struts.

vii) Vertical and horizontal fins individually or forming box louvers band, facias and eaves boards

ix) Lintels, beams, plinth beams, girders, bressumers cantilevers and with water proof ply 12mm thick

Supply of Steel reinforcement for R.C.C. including straightening, cutting, bending, placing in position and binding all complete at all levels

ii) Thermo Mechanically Treated Bars of Fe- 500D grade or more, conforming to IS1786

Providing and laying Brick work with common burnt clay F.P.S (non Modular) bricks of class designation 7.5 in foundation & plinth

i) Brick work in Cement mortar 1:4 (1 cement : 4 coarse sand) IN FOUNDATION AND PLINTH

ii) Brick work in Cement mortar 1:6 (1 cement: 6 coarse sand ) IN FOUNDATION AND PLINTH

iv) Brick work in Cement mortar 1:6 (1 cement: 6 coarse sand) in superstructure in all shapes & sizes in superstructure ABOVE PLINT H & UP TO FLOOR V LEVEL

x) Half brick masonry with common burnt clay F.P.S.(non modular) brick of class designation 7.5 in Cement mortar 1:4 (1 cement:4 coa rse sand in superstructure ABOVE PLINTH level & UP TO FLOOR V LEVEL

Providing and fixing 18mm thick gang saw cut mirror polished premoulded and prepolished, machine cut for kitchen platforms, vanity counters, sills, facias, Pump Island & similar locations of required size, approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding & polishing to edge to give high gloss finish etc. complete at all levels.

iii) Granite of any colour and shade having Area of slab upto 0.50 sqm

iv) Granite of any colour and shade having Area of slab over 0.50 sqm

Extra for providing edge moulding to 18mm Granite/ marble stone counters,Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in- Charge.

ii) Granite work

Extra for providing opening of required size & shape for wash basins/ kitchen sink in kitchen platform, vanity counters & similar lo cation in marble/Granite/stone work including necessary holes for pillar taps etc.including rubbing and polishing of cut edges etc.c omplete

Supplying and fixing of 10mm thick mirror polished black granite tiles for pump island edges etc. over 12mm thick CM 1:4 including c ost of all materials and labour etc. complete.

Providing & fixing MS grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc.including primi ng coat with approved steel primer (fixed to steel windows by welding) all complete.

Providing & fixing chrome plated brass100mm mortise latch with one dead bolt with 6 levers & a pair of lever handles with necessary screws etc. complete (best make of approved quality).

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer with double speed adjustment with necessary accessories and screws etc. complete.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixed with rawl plugs and screws or w ith fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions,at top, bottom & sides with w ith required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanical ly wherever required including cleat angle, Aluminium snap beading for glazing/panelling, C.P. brass/stainless steel screws includin g fixing all complete as per drawing & the directions of Engineer-in-charge. (Cost of glazing or panels to be paid for separately)

i) Fixed Glazing with Powder coated aluminium (minimum thickness of powder coating 50 micron) sections

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixed with rawl plugs and screws or w ith fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions,at top, bottom & sides with w ith required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanical ly wherever required including cleat angle, Aluminium snap beading for glazing/panelling, C.P. brass/stainless steel screws includin g fixing all complete as per drawing & the directions of Engineer-in-charge. (Cost of glazing or panels to be paid for separately)

iii) For shutters of doors, windows & ventilators with Powder coated aluminium sections including providing fixing hinges/ pivots & making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings sha ll be paid for separately)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket e tc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be pa id in basic item):

ii) With float glass panes of 5.0 mm thickness (weight not less than 12.5kg/sqm)

iii) With float glass panes of 8.0 mm thickness (weight not less than 20kg/sqm)

ii) With brass cover plate minimum 1.25 mm thickness

Providing and fixing Brass 100mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for al uminium doors including necessary cutting and making good etc. complete.

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and f ixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc for fixing re quired door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc. to be paid separately) .

Structural steel work riveted, bolted or welded in single section fixed with or without connecting plate including cutting, hoisting , fixing in position and applying a priming coat of approved steel primer all complete.

Structural steel work riveted,bolted or welded in built up sections, trusses & framed work, including cutting, hoisting, fixing in p osition and applying a priming coat of approved steel primer all complete:

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths interlocked together through their entire length,jointed together at the end by end locks mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete including the cost of providing and fixing necessary 27.5cm lo ng wire springs manufactured from high tensile steel wire of adequate strength conforming to IS 4454 Part-I & M.S. top cover of requ ired thickness for rolling shutters:- 80x1.25mm MS laths with1.25 mm thick top cover

Providing and fixing ball bearing for rolling shutters.

Steel work in built up tubular (round,square or rectangular hollow tubes etc) trusses etc. including cutting,hoisting fixing in posi tion and applying a priming coat of approved steel primer, including welded and bolted with special shaped washers etc. complete.

i) Hot finished welded type tubes

ii) Hot finished seamless type tubes

Fabrication & Erection of IOC supplied structural steel work riveted, bolted or welded in single/ built up sections,trusses & framed work hoisting, fixing in position and applying a priming coat of approved steel primer all including cutting, complete

Structural steel work in built up sections/ framed work in gratings, frames, guard bar, ladder, railings, brackets, gates and simila r works including cutting,hoisting,fixing in position & applying a priming coat of approved steel primer etc. as required.

25mm Thick Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete. with base of cement mortar 1 : 4 (1 cement : 4 coarse sa nd)

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cemen t 3 coarse sand)jointed with grey cement slurry mixed with pigment to match the shade of the slabs,including rubbing and polishing c omplete.

Providing & fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (minimum thickness of 5 mm) of approved make in al l colours,shades except burgundy,bottle green,black of any size as approved by Engineer-in-Charge in skirting,risers of steps and da dos over 12 mm thick bed of cement Mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm includ ing pointing in white cement mixed with pigment of matching shade.

Providing & laying Ceramic Glazed floor tiles 300x300 mm or more (thickness to be specified by the manufacturer) of 1st quality conf orming to IS : 15622 of approved make in colours White, Ivory, Grey, Fume Red Brown, laid on 20mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand) jointing with grey cement slurry@ 3.3kg/sqm including pointing the joints with white cement and matching pigments e tc. complete.

Providing & laying vitrified floor tile in different sizes (thickness as per manufacturer) with water absorption's less than 0.08% a nd conforming to IS : 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar as specified with coarse sa nd jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc. complete for flooring/skirting as specified

i) Flooring with size of Tiles 60x60Cm in cement mortar 1:4

iii) Skirting with size of Tiles 60x60Cm in Cement mortar 1:3

Providing corrugated G.S. sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead and including a coat of appr oved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curv ed surfaces) excluding the cost of purlins,rafters & trusses & including cutting to size & shape wherever required:- 1.00mm thick G. S. Sheet with zinc coating not less than 275gm/m²

Providing and fixing Klippon Galvalume steel profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge ) of Cold rolled steel confirming to IS:513-2008 of base metal thickness 0.50 mm, having Yield Stress of Min. 275 MPa. Steel surface shall have hot dip metallic coating of Al-Zinc alloy comprising 55% Alluminium, 43.5% Zinc and 1.5% Silicon as per the ASTM-A792M, with total mass of coating on both sides shall be 150 gms/sqm. The steel shall have organic coating with Silicon Modified Polyester (SMP) /Super Durable Polyester (SDP) paint on continuous coil coating line. The thickness of coating on top side shall be 20-25 Micr ons (i.e. 15-18 microns SMP /SDP paint over 5-7 microns epoxy primer) and back side 8-10 Microns SMP/SDP paint over epoxy primer. To tal Coated Thickness (TCT) shall be 0.58 MM. Sheet shall have protective guard film of thickness of 25 microns minimum to avoid scra tches while transportation and should be supplied in single length up to 6m or as desired by Engineer-in-charge.

ii) Plain Sheet for Ridges (500 - 600mm).

iii) Plain sheet for Flashings/ Aprons (Upto 600 mm)

iv) Plain Sheet for Gutter (600 mm over all girth)

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS:13592 Type A including jointing with sea l ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion, Single socketed pipes.

ii) 110 mm diameter

iii) 160 mm diameter

Providing & fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes confo rming to IS:13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion.

ii) 110mm Coupler

iv) 110 mm Single pushfit Coupler

vi) Single tee with door of 110x110x110 mm

viii) Single tee without door of110x110x110 mm

x) 87.5° Bend of 110 mm

xii) Shoe (Plain) of 110 mm

i) 160 mm UPVC Coupler

ii) 160 mm Single push fit Coupler

iii) Single tee with door of 160x160x160 mm

iv) Single tee without door of 160x160x160 mm

v) 87.5 degree bend of 160 mm

vi) Shoe (Plain) of 160 mm

Providing and fixing 150F/200F flush panel,(pre-coated steel) False Ceiling made of Cold rolled steel sheet conforming to IS 513, having minimum yield stress and tensile stress as 240 Mpa and 300 Mpa respectively. Base metal thickness for ceiling panel and Carri ers shall be 0.45mm and 0.55mm respectively. The steel surface shall have hot dip metallic coated with Zinc coating (galvanizing) as per IS277, with total mass of coating on both sides shall be 120 gms/sqm. The steel shall have organic coating with Regular Modifie d Polyester (RMP) paint on continues coil coating line. The thickness of coating on top side shall be 20-25 Microns (i.e. 15-18 micr ons RMP paint, over 5-7 microns epoxy primer) and back side 8-10 Microns RMP paint over epoxy primer. Total Coated Thickness (TCT) s hall be 0.50 MM for Ceiling panel and 0.60 MM for Carrier. Sheet shall have protective Sheet shall have protective guard film of th ickness of 25 microns minimum to avoid scratches while transportation and should be supplied in single length up to 6m (for panel) a nd up to 5m (for carrier) or as desired by Engineer-in-charge. The ceiling panel shall be clipped into carriers which are suspended from steel trusses/purlins with the help of GI suspension angle of size 25x25x0.5mm thick by means of rigid suspension system meant for exterior. The longitudinal joints of two panels shall be butt joined with a special type of panel splice to be fixed from inner side. The carrier will be joined with carrier splices maintaining a module of 150 mm. The spans shall not exceed as recommended and manufacturer recommendations shall be followed on installation procedure.

Providing & fixing BARE Klippon Galvalume steel profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-char ge) of bare metal thickness 0.55 mm as per ASTM A446 having yield stress of 275mpa, surface shall have hot dip metallic coating of Aluminium Zinc alloy comprising of 55% aluminium,43.5% zinc & 1.5% silicon, Sheet shall have protective guard film of 25 microns mi nimum to avoid scratches while transportation & should be supplied in single length up to 6m or as desired by Engineer-in-charge.

Supplying & fixing of 18 gauge GI plain sheet of approved make with necessary folding/ fabrication using hydraulic press for flashin g sheet / fascia, etc. in roofing / buildings / sheds etc. including all necessary fixtures etc., complete

Providing and laying cement plaster on surfaces with fine sand including curing etc.

i) 12 mm cement plaster of mix 1:4 (1 cement: 4 fine sand)

ii)12 mm cement plaster of mix 1:6 (1 cement: 6 fine sand)

v) 20mm Cement plaster of mix 1:4 (1 cement: 4 fine sand)

vi) 20mm Cement plaster of mix 1:6 (1 cement: 6 fine sand)

Providing and laying 6mm thick cement plaster on surfaces with fine sand including curing etc.

i) 6mm thick plaster of mix 1:3 (1 cement: 3 fine sand)

Providing Neat cement punning

Providing and applying plaster of Paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth comple te

Finishing walls with water proofing cement paint of required shade with Two or more coats applied @ 3.84 kg/10 sqm:

Finishing walls with Acrylic Smooth exterior paint of required shade (2 or more coat applied @ 1.67 ltr/10 sqm over & including prim ing coat of exterior Primer applied @ 2.20kg/10 sqm)

Finishing walls with Deluxe Multi surface paint system for interiors & exteriors using Primer as per manufacturers specifications wi th two or more coats applied on wall @ 1.25 ltr/10 sqm. over and including one coat of Special primer applied @ 0.75 ltr / 10sqm

Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @0.90 ltr/10 sqm over an under c oat of primer applied @ 0.80 ltr/ 10 sqm of approved brand or manufacture

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade with two or more coa ts over an under coat of suitable shade with ordinary paint of approved brand and manufacture.

Painting with aluminium paint of approved brand and manufacture to give an even shade with 2 or more coats

Extra for Spray painting in place of painting with brush or rollers on all type of surfaces.

Demolishing cement concrete manually/ by mechanical means including disposal of material outside premises at an unobjectionable pla ce as per direction of Engineer-in-charge.

i) 1:3:6 or richer mix (i/c equivalent design mix)

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars & disposal of unserviceable material outsid e site to an unobjectionable place as/ direction of Engineer-in-charge

Demolishing brick work manually/mechanical means including stacking of serviceable material & disposal of unserviceable material out side premises at an unobjectionable place as / direction of Engg-in-charge

Demolishing stone masonry manually/ by mechanical means including stacking serviceable material & disposal of unserviceable materi al outside site at unobjectionable place as per direction of Engineer-in-charge:

Dismantling Steel work in built up sections in angles, tees, flats channels etc. including all gusset plates, bolts nuts, cutting ri vets welding etc. including dismembering and stacking within premises

Dismantling roofing including ridges, hips valleys & gutters, False ceiling of any type and stacking the material within premises, o f:

i) G.S. Sheet/ Klippon galvalume sheet/ False ceiling panels

Dismantling manually/by mechanical means including stacking of serviceable material & disposal of unserviceable material outside si te at unobjectionable place as per direction of Engineer-in-charge :

i) Water bound macadam road

ii) Bituminous road

Demolishing C.C./R.C.C. work by mechanical means and stockpiling at designated locations and disposal of dismantled materials up to a lead of 1000 m, stacking serviceable and unserviceable material separately including cutting reinforcement bars.

Carriage charge for disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, stacking, unloading to approved municipal dumping ground/unobjectionable place as/direction of Eng g- in-Charge beyond IOCL Premises for all leads and including all lifts

i) Distance upto 1 km

ii) Distance > 1 km< 3 km

iii) Distance > 3 km< 5 km

iv) Distance > 5 km< 10 km

Dismantling granite slabs / granite tiles / marble slab on wall, floor, pump Island etc., stacking of the serviceable materials and disposal of damaged materials as directed by IOCL including all charges etc. complete

Laying of dismantled granite slab / granite tiles / marble slab over pump Island, wall, floor etc. including bedding in cement morta r 1:4, 20mm / 12 mm thick as per standard drawings and cost of all material and labour etc., complete.

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm. depth dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the s ub grade and disposal of surplus earth within premises

Construction of granular sub-base by providing close graded material conforming to specifications, mixing in a mechanical mixer plan t at Optimum Moisture Content, carriage of mixed material by tippers to work site, for all lead and lifts, spreading in uniform laye rs of specified thickness with motor grader on prepared surface & compacting with vibratory power roller to achieve the desired dens ity, complete as per specification & direction of Engineer-in-charge.

i) With material confirming to grade-I (size 75 mm to .075 mm) having CBR value - 30, Thickness as desired

Providing, laying, spreading and compacting graded stone aggregate (size range 53 mm to .075 mm) to wet mix macadam (WMM) specificat ions including premixing the material with water at OMC for all leads and lifts, laying in uniform layers with mechanical paver fini sher in sub-base/base course on well prepared surface and compacting with vibratory roller of 8 to 10 ton capacity to achieve the de sired density, complete as per specifications & directions of Engineer-in- charge

Providing & laying factory made reflective type Lacquered finish Grey / coloured pre-cast cement concrete, interlocking paver block of specified grade made by block making machine wih vibratory compaction & of approved size and design / shape, shade and manufactur ers and as per IOCL's specifications. The paver blocks shall have peripheral chamfer, with average crushing strength as per IS 15658 , maximum water absorption of 2% after 10 minutes and 5% after 24 hrs. as per BS 1881, maximum dimensional deviations of +/- 2mm on length @ width and +/- 3 mm on thickness. The job includes supplying and laying a layer of 50 mm thick clean coarse sand on thorough ly compacted sub-base below the paver blocks, cutting the paver blocks wherever required with hydraulic splitter, filling in the joi nts at the edges of paver blocks with sand, compacting with machine vibrator to required line and level, etc. complete. (Payment for provision of edge restraints shall be made separately)

ii) M40 grade 80 mm thick reflective type Lacquered finish

Taking out existing CC interlocking paver blocks from footpath central verge, including removal of rubbish etc., disposal of unservi ceable material out of site at unobjectionable place and stacking serviceable material within premises as per direction of Engineer - in-Charge

Laying Corporation supplied interlocking paver blocks of any design /shape laid in required line,level,curvature,colour & pattern ov er and including 50mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as/ direction of Engin eer-in-charge.

Providing and fixing 600x450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board gro und fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including a ll CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & f ittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.Internal work - Expo sed on wall

v) 40 mm nominal outer dia Pipes

vi) 50 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including al l CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fitting s with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed work including cutting chases and making good the walls etc.

i) 15 mm nominal outer dia Pipes

ii) 20 mm nominal outer dia Pipes

iii) 25 mm nominal outer dia Pipes

iv) 32 mm nominal outer dia Pipes

Providing and fixing B class G.I. pipes complete with G.I. fittings including trenching and refilling etc for WATER and AIR, Externa l work

i) 15 mm dia. nominal bore

Providing and fixing brass bib cock of approved quality :

i) 15 mm nominal bore

ii) 20 mm nominal bore

Providing and fixing brass stop cock of approved quality :

i) 15 mm nominal bore

ii) 20 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :

i) 25 mm nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :

i) 15 mm nominal bore

i) 100 mm diameter

ii) 150 mm diameter

Constructing masonry Chamber 60x60x75 cm,inside in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valves etc, with CI surfa ce box 100mm. top diameter,160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size), i/c necessary excavation foundation concrete 1:5:10 (1 cement : 5 f ine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement:3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S (non modular) bri cks of class designation 7.5

Constructing masonry Chamber 90x90x100 cm, inside in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for Sluice valves e tc, with CI surface box 100 mm. top diameter,160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) necessary excavation,foundation concrete 1:5:10 (1 c ement : 5 fine sand:10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design: With Common burnt clay F.P.S (non m odular) bricks of class designation 7.5

Providing and placing on terrace (at all floor levels) polyethylene water storage tank IS : 12701 marked with cover and suitable loc king arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. - 15 mm nominal bore

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C. I.cover with frame of 300 x300 mm size(inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design :

i) 100x100 mm size P type with common burnt clay bricks of class Designation 7.5

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in th e proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : Light Duty

ii) 150 mm dia. R.C.C. pipe

iii) 250 mm dia. R.C.C. pipe

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and SW drain pipe 100 mm diamet er, 1.8 m long complete as per standard design with common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and fixing 700mm wide rain water gutter fabricated out of 1200mm wide Roll of 18 Gauge Aluminium sheets including MS clamp supports, fittings, fasteners etc. complete as per drawing . (NO joints shall be provided in the gutter and the same has to be fabr icated from a continuous roll of Aluminium sheet)

Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer, 3mm thick water proofing membrane, black finished reinforced with glass fibre matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 ltr/sqm. by the same m embrane manufactured of density at 25°C, 0.87 - 0.89 kg/ltr and viscosity 70 - 160 cps. Over the primer coat the layer of membrane s hall be laid using butane torch and sealing all joints etc., and preparing the surface complete. The vital physical and chemical par ameters of the membrane shall be as under : Joint strength in longitudinal and transverse direction at 23°C as 350/300 N/5cm. Tear s trength in longitudinal and transverse direction as 60/80N. Softening point of membrane not less than 150°C. Cold flexibility shall be upto - 2°C when tested in accordance with ASTM, D - 5147. The laying of membrane shall be got done through the authorised applica tor of the manufacturer of membrane : 3mm thick

Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50mm including strengthening with 2mm dia GI w ire or nuts, bolts and washers as required complete as per the direction of Engineer-in-charge using hot dipped galvanised wire of 4 mm dia (The rate for civil works for excavation, brick masonry, PCC shall be paid separately)

Supply and Laying of 50 mm dia single wall flexible piping system comprising of Non-metallic HDPE (flexible) pipelines as per IOCL s pecifications and with manufacturer supplied fittings including all bends, tees, elbows, reducers, end connectors at DU & tank side etc and as required for complete underground piping job. The joints in the pipelines, except the end connections at tanks and dispen sers shall be made by electro-fusion welding. The pipes shall be suitable for use with petroleum and ethanol blended fuels. The maxi mum operating pressure shall be 7Kg/sq.cm. Note: The make of HDPE Pipe should be CCOE approved. Pressure testing shall be done befor e the final backfilling. The civil works for installation viz. excavation, sand filling & back filling etc. shall be paid seperatel y. All metallic parts in the piping system shall be grounded as per the requirements of EN14125.

Supply and Laying of 80 mm dia single wall flexible piping system comprising of Non-metallic HDPE (flexible) pipelines as per IOCL s pecifications and with manufacturer supplied fittings including all bends, tees, elbows, reducers, end connectors at DU & tank side etc and as required for complete underground piping job. The joints in the pipelines, except the end connections at tanks and dispen sers shall be made by electro-fusion welding. The pipes shall be suitable for use with petroleum and ethanol blended fuels. The maxi mum operating pressure shall be 7Kg/sq.cm. Note: The make of HDPE Pipe should be CCOE approved. Pressure testing shall be done befor e the final backfilling. The civil works for installation viz. excavation, sand filling & back filling etc. shall be paid seperatel y. All metallic parts in the piping system shall be grounded as per the requirements of EN14125.

Supplying and fixing MS foundation bolts with necessary GI nuts and washers of specified sizes,all conforming to relevant Indian Sta ndards and as approved by Engineer-in-charge :

v) 25mm dia x 1000mm long with 100 mm dia x 8 mm thick plate

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-c hambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape and size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame and sash shall be mitred cut and fusion welded at all corne rs, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjace nt finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all co mplete as per approved drawing and direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shal l be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth and width of profile shall be a cceptable.

Two track two panels sliding window made of (small series) frame 52 x 44 mm and sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area of window upto 1.75 sqm)

Three track three panels sliding window with fly proof SS wire mesh (Two nos. glazed and one no. wire mesh panels) made of (small se ries) frame 92 x 44 mm and sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimensi on (Area of window upto 1.75 sqm).

Providing and fixing of square composite (FRP) Manhole Cover with frame D400 with 40T load bearing capacity, all complete and as per drawing, specification and direction of Engineer-in-charge. Note: Diameter would be clear opening of cover.

iii) 900 X 900 mm

Providing and fixing of lifting handle foot lever for use with flat sealed cover and trench panels of OPW Fiberlite or equivalent ma ke make as per specification and direction of Engineer in charge.

Providing and fixing Chrome Finish SS Health faucet with 8mm dia, 1 meter long SS braided rubber hose pipe and wall hook with N.R.V, Jaguar make cat. No. ALD-577 or equivalent all complete, as per specification and direction of Engineer-in-charge.

Providing and fixing of SS single Soap tray with all fittings and all complete, as per specification and direction of Engineer-in-ch arge.

Providing and fixing 450 mm long CP Brass towel rail complete with brackets fixed to wooden/PVC cleats with SS screws with concealed fittings arrangement of Make: Cera F5007104 or equivalent all complete and as per direction of Engineer-in-charge.

Providing and fixing first quality (heavy duty) type glazed vitreous china P or S trap Wall hung coloured water closet, seat cover, CP nuts, bolts and other necessary fittings all complete and as per specification and direction of Engineer-in-charge.

Providing and fixing of toughened glass with suitable arrangement, all complete as per drawing, specification and direction of Engin eer-in-Charge

iii) 12 mm thick

Providing and fixing H type double tone SS Pull handle of GODREJ (7268) or equivalent make with all tools, tackles etc. all complete , as per specification and direction of Engineer-in-charge.

Providing and fixing stainless steel (SS 304) railing made of hollow tubes, channels, plates etc. including welding, grinding, buffi ng, polishing and making curvature (wherever required) and fitting with necessary stainless steel nuts and bolts complete including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size on the top of the floor or the side of the waist slab with suitable arrangement, all complete as per specification and direction of Enginee r-in-charge.

IOCL LOGO

RETRO STICKER

Dismantling of Canopy RVI

Dismantling Canopy Column Cladding

Sales Building Demolition

S/F of Counter sunk - Wash Basin of size 465x320x150 mm including 305mm Pillar Tap, 32mm Waster Coupling, 300mm Bottle Trap etc. com plete

RAZE AND REBUILD VETERAN CO (PM)

Installation of supplied 20 KL Tank as per specified drawings as per work description but excluding all works of kerb wall and Gaske t for manhole including painting / doping with Shalimastic HD as applicable as per specifications complete. RCC works wherever menti oned shall be of grade M20

iii) In brick masonry pit with RCC strip under driveway including RCC top slab as per standard Drg. ENG/317. Manhole cover plates an d frame to be paid separately .

Supply, fabrication, laying and testing of MS, BLACK, ERW, threaded pipes, heavy class conforming to IS 1239, PART I as per IOCL spe cifications including pipeline fittings like bends, tee etc as required and as directed for Underground pipeline with doping

iv) S/L Threaded U/G HD MS Pipes of 40 mm dia with fittings,doping

Supply, fabrication, laying and testing of MS, BLACK, ERW, threaded pipes, heavy class conforming to IS 1239, PART I as per IOCL Spe cifications including pipeline fittings like bends, tee etc as required and as directed for Above Ground pipeline including surface preparation according to standard SSPC ST2 and painting with 2 coats of red oxide zinc phosphate primer and 2 coats of Synthetic ena mel / aluminium finish paint as per IOCL specifications

iii) S/L Threaded A/G HD MS Pipes of 50 mm dia with fittings,Painting

iv) S/L Threaded A/G HD MS Pipes of 40 mm dia with fittings,Painting

Supply, fabrication, laying and testing of MS black, ERW welded, pipes, heavy class conforming to IS 1239, PART I as per IOCL specif ications including pipeline fittings like bends, tee etc as required and as directed for Underground pipeline with doping

ii) S/L Welded U/G HD MS Pipes of 80mm dia with fittings,doping

iii) S/L Welded U/G HD MS Pipes of 50mm dia with fittings,doping

Fabrication, Installation, Welding & testing of Corporation supplied MS or GI pipes for Underground pipeline with doping. Pipeline fittings 80 mm dia and below is to be supplied by party.

ii) U/G Laying IOC supplied MS/GI pipes of 80mm dia with fittings upto 80mm dia with doping

iii) U/G Laying IOC supplied MS/GI pipes of 50mm dia with fittings upto 80mm dia with doping

iv) U/G Laying IOC supplied MS/GI pipes of 40mm dia with fittings upto 80mm dia with doping

Fabrication, Installation , Welding & testing of Corpn supplied MS or GI pipes for Above ground pipeline including surface preparati on according to standard SSPC ST2 and painting with 2 coats of red oxide zinc phosphate with 2 coats of red oxide zinc phosphate / a luminium finish paint as per IOCL specifications. Pipeline fittings 80 mm dia and below is to be supplied by party.

iv) A/G Laying IOC supplied MS/GI pipes of 40 mm dia with fittings upto 80mm dia , painting

Supply & welding slip-on flanges conforming to IS2062 GrA, ANSI B16.5, Class#150 with 3 runs of weld outside and one run of weld ins ide the flanges as per specifications and standard Drg.enclosed herein

ii) S/W Slipon flanges of 80 mm dia conforming to IS2062 GrA, ANSI B16.5,Class 150 as per specifications and standard Drg.enclosed herein

iii) S/W Slipon flanges of 50 mm dia. conforming to IS2062 GrA, ANSI B16.5,Class 150 as per specifications and standard Drg.enclosed herein

Making flanged joints between flanges slip on, blind and flange etc. including providing/supplying 3 mm thick permanite oil gasket, nuts, bolts, bonding with 3 mm dia copper wire etc.complete as per IOCL specifications.

ii) Making Flange joint between Slip on, blind and flange etc.of 80 mm dia. including gasket, nuts, bolts,3mm dia copper wire bondin g

iii) Making Flange joint between Slip on,blind and flange etc.of 50 mm dia. including gasket, nuts, bolts,3mm dia copper wire bondin g

Supplying and installation of the following threaded coupling

ii) 80 mm dia Aluminium camlock coupling - Male & Female

Supply and installation of ‘U’ type CS bend on the vent pipes including painting as per specifications and supplying and brazing wi re mesh of 11 mesh per linear centi-meter of non-corrosive metal in two layers on both ends.

ii) Supply & installation of U type CS bend on vent pipe of 50 mm dia

iii) Supply & installation of U type CS bend on vent pipe of 40 mm dia

Supply and installation of screwed type gun metal valves as per IOC specifications: Angular Check Valve

i) S/I Screwed type GM Angular Check Valve of 50 mm dia

Supply and installation of screwed type gun metal valves as per IOC specifications: Ball Valve

ii) S/I Screwed type GM Ball Valve of 80 mm dia

iii) S/I Screwed type GM Ball Valve of 50 mm dia

Air compressor Supply and installation of horizontal air compressor assembly with delivery pressure of 12 kg/sq cm equipped with pre ssure gauge, non- return/safety/drain/delivery valves, automatic cut-off switch and suitable electrical connections & all standard a ccessories, including civil works:

i) Installation of DU Including providing necessary anchor bolts and C.C. foundation

Installation of supplied Multi Product Pumps / Dispensers on pump island as per manufacturers installation manual, drawings, includi ng supplying, providing necessary frame of ISMC 100, foundation bolts, supplying and filling required quantity of dry sand in pit(s) below the pump

i) 2 product - 4 nozzle MPPs/MPDs

Transportation of equipment from one location to another location including enroute all taxes, levies and unloading/loading by a s uitable vehicle exclusively for this purpose (In case of tank same shall be loaded by the tank fabrication contractor)

iii) 15/20 KL Tank with fittings : 0 - 30 Km

iv) 15/20 KL Tank with fittings: Add extra for each addtnl. Km above 30km

vii) Mono/Duo pump/Air Comp/STP/All other pumps - upto 2 nos,0-30 Km

viii) Mono/Duo pump/Air Comp/STP/All other pumps - upto 2 nos, Add extra for every additional Km above 30km

xi) MPD/MPP pumps upto 2 nos., 0-30 Km

xii) MPD/MPP pumps upto 2 nos., Add extra for every additional Km above 30km

Testing the tank hydro-statically with fresh water, to a pressure of 0.75 Kg/Sq.cm. (Testing includes supplying, filling and emptyin g out the water after testing) cleaning the internal surface of the tank etc. complete.

iii) Hydro Testing 20KL Tank with fresh water@ pressure 0.75Kg/Sqcm

EMPTYING OUT PRODUCT FROM UNDER GROUND TANKS Removing product from the under ground tanks and emptying it including collecting the p roduct in barrels supplied by the Corporation. It shall be ensured that no loss of product is taken place, while carrying out the jo b. The job will be carried out in the presence of Corporation and dealers representatives

Supplying & Filling fresh water in the underground tank (10/15/20/50/ 70KL) to avoid floating of the tanks during monsoon, etc. as d irected.

Removing the water carefully from U/G tank with SR pump, in such a way that there is no loss of product. The water has to be thrown away and the product to be put back into the tank etc. complete.

Exhuming of tanks of following capacities with fittings. Item includes excavation wherever required , dismantling of tank with fitt ings , Pipeline connections , man hole cover plates if any , removing dead stock , sludge oil and storing them in barrels at safe pl ace , degassing , exhuming tank from the pit stacking of the tank within premises etc. as per specifications . Back filling , disman tling of RCC Slab , masonry shall be paid separately .

ii) Exhuming of tanks of 15 KL Tank

iii) Exhuming of tanks of 20 KL Tank

Removing connected dispensing pump from pedestal including disconnection of pipeline, electrical connection, removal of nuts of the foundation bolts etc. complete.

Re-installing the dispensing pump on existing foundation including connecting pipelines, electrical connections, tightening nuts of the foundation bolts etc. complete.

i) Re-installing Mono/Duo pump on existing foundation including connecting pipelines, electrical connections, tightening nuts etc.

ii) Re-installing MPD / MPP on existing foundation including connecting pipelines, electrical connections, tightening nuts etc.

Disconnecting, dismantling the existing pipeline both above/ Underground including excavating, breaking the enclosure walls, back fi lling & restoring the surface in original condition, disconnecting all the fittings, valves, strainers, filters, adjustable supports and all other fittings either by gas-cutting or hacksaw cutting after gas the lines, dismantling BM pedestals if required and stack ing the dismantled pipes and fittings at site as directed

vi) Dismantling and stacking 80 mm dia - UG P/L

vii) Dismantling and stacking 50 mm dia - UG P/L

Disconnecting, dismantling the existing screwed pipeline both above/ underground including excavating, back-filling, restoring the s urfaces into original condition, disconnecting all fittings, stacking the dismantled pipes/fittings at site as directed.

iii) Dismantling and stacking 40 mm dia A/G P/L

viii) Dismantling and stacking 40 mm dia U/G P/L

Supply and fixing Pressure Vacuum Valves of 2 inches for fixing to the Vent Pipes of Underground MS tanks. The valve should be in cl osed position at normal operating pressure of the tank. The Valve shall be capable for activation at set pressure of 3" ± 0.5 water column to release excess pressure of tank to the atmosphere and open at vacuum of 8" ± 2.0 water column to induce the atmosphere pre ssure to the tank. PV valve should be diaphragm of dead weight or spring loaded type or combination of any. The weight of the PV va lve shall not exceed 2.0 kg. top of the valve shall be provided with cover/cap/ weather hood to prevent the entry of rain water. Val ve material,Cover and adopter shall be of Aluminium/polypropylene, diaphragm if used should be of Neoprene, O ring should be of rub ber/neoprene, Net/Mesh Pressure puppet ,Vacuum puppet,screws and spring should be of stainless steel. Suitable adopter with one end fitted with valve and the other end should have threading for fixing on Vent pipe of 40mm. PV valves shall have: UL 842 certificatio n of CARB approval or test certificate from any Govt.lab. PV valve shall have PESO approval.

Providing alteration to Manhole Covers for Fixing Submersible Turbine Including Fixing of 100mm diax 150 to 200mm long C class threa ded Barrel Nipple , 100mm dia x 100 mm long coupler , 2 nos 100mm dia Class 150 threaded MS flange, 3mm thick packing sheet, nuts an d bolts, 3mm thick permanite oil packing gasket to manhole cover, cutting of the manhole cover for fixing nipples etc. at workshop i ncluding transportation etc.

Installation of Corporation supplied Standard Submersible Turbine Pump on the existing Manhole Cover as per drawing and direction of Engineer in Charge

Painting of DUO pump with spray -inner surface with one coat of metal primer and outside surface with dry film thickness of minimum 40 micron with synthetic enamel paint of approved colour & quality including cleaning , scrapping of surface before painting. Work i ncludes supplying and fixing of lettering of IOC logo - 2nos., name of the product in English & Devangiri - 2 nos.

Painting of MPP/ MPD pump with spray -inner surface with one coat of metal primer and outside surface with dry film thickness of min imum 40 micron with synthetic enamel paint of approved colour & quality including cleaning , scrapping of surface before painting. W ork includes supplying and fixing of lettering of IOC logo - 2nos., name of the product in English & Devangiri - 2 nos.

Dismantling of Air Gauge

Re-installation of Air gauges

Dismantling of Air Compressor

Re-installation of Air Compressor

CABLING AND ALLIED WORKS - ARMOURED CABLES Supply & laying of XLPE insulated PVC sheathed aluminium/copper conductor, 1.1 kV grade armoured cable conforming to IS:7098, as per approved make in ground/ trench/surface/pipe, etc. whereever required as per direction of Engineer In-charge. Note: The rate of Installation should be inclusive of Cable clamps, tags Saddles, Consumables etc. Trays/pipe s, trenches, fabricated tray supports etc will be covered & paid in Separate Items

iii) 3 Core x 1.5 sq. mm. (copper)

iv) 3 Core x 2.5 sq. mm Copper Cable FRLS

v) 4 Core x 2.5 sq. mm Copper Cable FRLS

vi) 3 Core x 1.5 sq.mm Copper Cable FRLS

Re-laying corporation supplied cable complete as per specification

i) 1.5 sq.mm to 2.5 sq.mm XLPE

ii) 4 sq.mm to 10 sq.mm XLPE / AYFY

iii) 16 to 35 sq.mm XLPE / AYFY

iv) 50 sq.mm to70 sq.mm XLPE / AYFY

SUPPLY AND LAYING OF FLAT CABLES

i) 3core, 2.5 sq.mm copper Flat Cable for submersible pump

ii) 3core, 4 sq.mm copper Flat Cable for submersible pump

CABLE TERMINATION GLANDS NON-FLP HEAVY DUTY DOUBLE COMPRESSION Cable Termination (NON FLP): Providing termination of 1.1 kV grade ar moured cable for the following sizes including supply of NON FLP heavy duty Double Compresson cable glands, crimping type lugs and allied jointing materials, etc. all complete as per specification and direction of Engineer In-charge. Glands and lugs shall be of approved make. Copper lugs for copper cables and aluminium lugs for aluminium cables shall be used.

vii) 3 Core x 2.5 sq. mm

xi) 4 Core x 2.5 sq. mm

CABLE JOINTING Cable Jointing : Providing straight through joint of following 1.1 KV grade XLPE insulated armoured cable with M-Seal make jointing kit, and other jointing material, etc. all complete including supply of all materials as per specification & directio n of Engineer In-charge.

vii) 3 Core x 2.5 sq. mm

xi) 4 Core x 2.5 sq. mm

xvi) 3.5 Core x 25 sq. mm

xvii) 3.5 Core x 35 sq. mm

xviii) 3.5 Core x 50 sq. mm

xix) 3.5 Core x 70 sq. mm

Supplying and installing of GI cable route marker with 100mm x 100mm x5mm thick GI Plate with inscription thereon, bolted/welded to 35mm x 35mm x 6mm angle iron, 600mm long and fixing the same in ground as per drawing & direction of IndianOil Job includes painting with one coat of redoxide & finishing paint

Supplying, fabricating and installing following sizes of perforated GI cable trays including horizontal and vertical bends, reducers , tees, cross members and other accessories as required and duly suspended from the ceiling and/or fix to steel/RCC columns, beams o r any other structure members with MS suspenders, angles, channels, etc complete as per the direction of IndianOil

iv) 300mm x 25mm x 2mm

Supply & fixing of flame proof junction box (4 way entry) of BALIGA /CEAG-FCG/FLEXPRO/FEPL make including clamping arrangement, all complete as per specification and direction of Engineer In-charge.

PROVISION OF EARTHING

ii) Providing earthing with 80 mm dia,3.0 M long GI (Heavy duty) perforated pipe as per IS:3043 (with latest ammendment) including p roviding suitable earth bus for interconnection, providing a mixture of salt & charcoal, making earth pit chamber with chequered pla te cover as per standard Drwng. etc. all complete as per specification & direction of Engineer-In-charge

Supply & drawing/laying, jointing, connecting, testing and commissioning of earth strip/copper strip/GI wire for earthing and light ning protection under or aboveground complete as per specification for the following :

i) 50 x 10mm G.I. Strip

ii) 32 x 6 mm G.I.strip

iii) 50 x 6 mm G.I. Strip

v) 25 x 3 mm GI strip

Providing & fixing flexible copper cable PVC insulated of 16sqmm for connecting the earth grid/earth strip with the crocodile clip i /c cost of 1 no. crocodile clip (for tanker earthing & other job)

Supplying & Fixing of following items for electrical safety in switch rooms/DG rooms etc

i) Electrical insulating mats made of PVC Elastomer 3mm Thick & 1 mtr wide near swichboards, etc as per direction of Engineer In cha rge. Mat should conform to IS 15652 Class A - suitable for safe working voltage of upto 33 kV. Test certificate to be provided with supply. Mat's top Surface should be Antiskid Dotted & Bottom Surface should be Textured for Floor Grip. Mat's top Surface should be Antiskid Dotted & Bottom Surface should be Textured for Floor Grip.

ii) 6 mm thick chequered plate on cable trench inside swtich room, DG room, earthing pit including cutting, painting, lifting hooks, etc

iii) Supply and fixing of shock treatment chart in English, Hindi & local language framed in glass framework.

iv) 11 KV grade hand gloves, ISI mark

Providing, fixing, testing and commissioning of FLP junction box of approved make for cable connection/ jointing.

Supplying, drawing sub-main/power wiring with PVC insulated Copper 1100 V grade FRLS type through heavy duty rigid PVC conduit eithe r on wall or in concealed. The job include terminations at both ends through proper jointing materials all complete for the followin g Make of Insulated wires shall be as per approved make

i) 2 x 1.5 sq mm + 1 x 1.5 sq mm earth wire

ii) 2 x 2.5 sq mm + 1 x 2.5 sq mm earth wire

iii) 2 x 4 sq mm + 1 x 4 sq mm earth wire

vi) 2 x 16 sq mm + 1 x 16 sq mm earth wire

SWITCHES, FUSES, MCBS, ELCBS ETC Supply and fixing of Modular switch frame with inner and outer face plates and accessories as per f ollowing details of approved including flush metal boxes/surface mounting boxes, plates, etc. all complete as per manufacturer's sp ecification and direction of Engineer In-charge.

i) 1or 2 module frame

ii) 3 module frame

iii) 4 module frame

iv) 6 module frame

v) 8 module frame

vi) 12 module frame

vii) 6A Modular Switch

viii) 15 A Modular switch

ix) 6A, 3 Pin Modular Socket

x) 15 A 6 Pin Modular socket

xii) Fan Regulator of stepped modular type

Supplying and fixing of following MCBs with necessery inter connections on existing DB, Panel board etc.

i) Upto 32A SP MCB

ii) Upto 32A DP MCB

Supply and installation of MCB distribution board having Double door complete with tinned cu bus bar, neutral bus bar, earth bar, din bar, interconnection, earthing etc. without incoming isolator and MCBs

iv) 4 way (4+12) TPN

Supply, installation, testing & Commissioning of wall mounted switchboard in sheet enclosure consisting of 110 A, 4P, 50 kA, Contact or, 230V AC trip coil, START / STOP Push button, ON / OFF Indication lamp(LED), Auxiliary contactors, Power & Control Terminals. Pus h buttons and indication lamps shall be mounted on front door. 2 Nos. of SP 6A MCB shall be mounted on front door. MCB shall get inc oming supply from incomer terminal of Contactor. Outgoing from MCBs shall be wired uptoterminals inside enclosure. The enclosure sha ll have 6 nos. of cable entry, 2 nos. suitable for 3.5Cx35 sq mm cable & 4 entry suitable for 3Cx2.5 sq mm cable. The work includes supply and installation of enclosure, Contactor, MCBs lamp, Push buttons, terminals, internal wiring (Contactor Make: L&T/GE/C&S/Sie mens/ABB).

Supplying and fixing 12 volt Charged LA battery of approved make for Electronic dispensing pumps including giving necessery electric al connection for the following AH ratings.

i) S/I of 12 Volt, 7AH Charged LA battery of approved make with stand

CONSTANT VOLTAGE TRANSFORMER Supplying, installation, testing and commissioning of single phase, air cooled constant voltage transfo rmer of approved make having input voltage range of 180-260V and output voltage of 220/230V with sine wave output wave form and havi ng automatic current limiting and short circuit protection including all accessories complete (for displays) for the following VA r atings.

iii) 500VA CVT

SINGLE SERVO VOLTAGE STABILISER Supply and fixing of 230V, Single phase, AC Servo voltage stabilizer of approved makes,(Range - 180 - 250 minimum) shall be provided for Individual dispensing pump as per IE Regulation and as per specification

iv) 5KVA stabilizer

THREE PHASE SERVO STABILIZER Supplying and fixing of 3 phase air cooled servo stabilizer for balanced and unbalanced load shall be i ndependent correction of each phase (Range 300 - 460 V minimum) and as per specification

v) 30 KVA stabilizer

Supply, fitting, fixing of arm bracket, tubular type, 38mm/50mm dia on pole including painting, all complete.

i) S/E Arm " L " bracket 38/50mm dia on pole, as per specifications and direction of Engineer in charge

Supplying & drawing inside the poles 3 core 2.5 sq.mm PVC insulated flexible copper conductor, fixing of junction box at the pole ba se (excluding supply of JB), making all connections on both ends, all complete as per specification and direction of Engineer In-cha rge.

i) "Y" Pole

ii) "L" Pole

OCTAGONAL POLES Supply & Fixing of Octagonal Poles of following type (Civil job shall be paid separatly) :

iii) S/E of 5 Meter high galvanised Octagonal pole with top 60mm(A/F), bottom 130mm (A/F) made up of 3 mm thick plate having a base plate of size 210 x 210 x 12 with single arm 1500mm long bracket arm made up of 48 O.D. pipe with EN 8 grade galvanised foundation b olts and anchor plate on suitable concrete foundation as per standard drawings enclosed herein(Civil & Electrical works shall be pai d separately) having fixing arrangement for mounting 2 Nos. of 250W Metal halide luminaries (on opposite sides)

INSTALLATION OF THE SUPPLIED LIGHT POLES

i) Erection, Installation and commissioning of company supplied yard light poles including grouting in C.C. & painting, internal wi ring, etc complete as per direction of Engineer In-charge (Civil job is included but painting shall be paid separately).

Supply and fixing of 100 W LED (Light Emitting Diode) light fixture with fittings and accessories for Yard lighting purpose having I P66 protection class with Pressure Die Cast LM6/ADC12/LM24 housing and with toughened glass or UV stabilized polycarbonate cover typ e of approved make or equivalent as per direction of Engineer-in-charge. The LED driver shall have an in-built high voltage cutoff > = 290 V with power factor of complete fitting greater than 0.90. CCT (Correlated Colour temperature) shall be in the range of 5665 K +/- 355 K as per ANSI standard C78.377, CRI (Colour rendering index) should include all colour range from R1 to R15 and > 70 for ou tdoor luminaire. LED efficacy shall be greater than 140 lumens/watt @ 350mA drive current. The minimum system lumen efficacy of the luminaire shall be 100 Lumens per Watt. The Surge Protection Device (SPD) should be series type with fail safe, surge protection for minimum 3kV shall be provided. Supply of complete fitting with all accessories as per specification attached and as per direction o f engineer in charge. Each lot of fittings shall accompany test certificates LM79/ IS:16106 and reference/ batch nos of LEDs and fit tings for verification at site. The supply of LED lighting shall be covered by a warranty of minimum 60 months from the date of supp ly of the lighting and the LED light fitting shall be complete in all respects including LED, LED Driver, Electronic circuitory, Lum inaire etc.

Supply and Fixing of Discrete LED (Light Emitting Diode) Tube lights of 18 Watt, having IP65 protection class with Pressure Die Cast Aluminium housing & with Polycarbonate diffuser of approved make or equivalent as per direction of Engineer in charge. The LED shal l be operating under voltage range of 140-270V with power factor more than 0.9. CCT(Correlated Colour temperature) shall be 5700 Kel vin (5665 K +/- 355 K), CRI (Colour rendering index) not less than 65. LED efficacy should be minimum 100 lumens/watt. The driver sh all be of constant volt & constant current type with internal surge protection. Each lot of Fittings shall have serial numbers and a ccompany LM79 / IS 16106 test reports and reference/batch nos of LEDs and fittings for verification at site. The supply of LED light ing shall be covered by a warranty of at least 72 months from the date of supply of the lighting and the LED light fitting shall be complete in all respects including LED, LED Driver, Electronic circuitory, Luminarie etc.

Supply and Fixing of Discrete LED (Light Emitting Diode) Tube lights of 8 Watt, having IP20 protection class with Pressure Die Cast Aluminium housing & with Polycarbonate diffuser of approved make or equivalent as per direction of Engineer in charge. The LED shall be operating under voltage range of 140-270V with power factor more than 0.9. CCT(Correlated Colour temperature) shall be 5700 Kelv in (5665 K +/- 355 K), CRI (Colour rendering index) not less than 65. LED efficacy should be minimum 100 lumens/watt. The driver sha ll be of constant volt & constant current type with internal surge protection. Each lot of Fittings shall have serial numbers & acco mpany LM79 / IS 16106 test reports & reference/batch nos of LEDs & fittings for verification at site. The supply of LED lighting sha ll be covered by a warranty of at least 72 months from the date of supply of the lighting and the LED light fitting shall be complet e in all respects including LED, LED Driver, Electronic circuitory, Luminarie etc.

CEILING FANS Supply & fixing of ceiling fan for inside of the sales building of following type:

ii) 900 MM Sweep

iii) 1200 mm sweep

EXHAUST FANS Supply and fixing of exhaust fan including electrical wiring all shall be with per specification and direction of site In charge. The fans shall be with louvers / shutters. (The job does not include making suitable cut out in the wall for fixing the fan).

ii) 9" dia light duty, make Khaitan or equivalent

DISMANTLING Dismantling of following electrical fittings / fixtures with all leads and lifts.

i) Electrical cables of all sizes from under / above ground position

Dismantling of light poles

Painting of Main Electrical Panel Board with two coats of synthetic enamel paint of approved make after thoroughly cleaning the surf ace.

Panel Board Stickering work

Panel Board marking of outgoing identification work

Preparation of single Line diagram - Electrical Layout

Preparation of single Line diagram - Earthing Layout

Supply and fixing of Linear Recessed mounted LED (Light Emitting Diode) Light fittings of size 2400mm and 80 Watt, having IP 65 prot ection class with Pressure Die Cast Aluminium housing and with Polycarbonate diffuser of approved make or equivalent as per directio n of Engineer-in-charge. High Efficiency Translucence(HET) diffuser. Colour Rendering Index CRI>80, Temp-0 to 45 Deg C, Driver effic iency>85%, THD < 10%, CCT- 6500 K Powerfactor>0.95, Surge protection-2 kV, Multistage Isolated Constant Current-Constant Voltage ope rated driver with range 140-270V AC and Safety Extra Low Voltage Safe level < 60V DC as per IEC standard, Luminaire lumen ≥ 2100lm. Each lot of Fittings shall have serial numbers & accompany LM79 / IS 16106 test reports and reference/batch nos of LEDs and fittin gs for verification at site. The supply of LED lighting shall be covered by a warranty of at least 72 months from the date of supply of the lighting and the LED light fitting shall be complete in all respects including LED, LED Driver, Electronic circuitory, Lumin arie etc

Dismantling of existing Retail Outlet main Electrical Panel by disconnecting all the incoming cables/earth strips etc & keeping inta ct all the existing panel switches/meters/changeovers/ MCBs /ESD etc including internal wirings with the Bus Bar for reutilisation a t another location within existing Retail Outlet or any alternate Retail Outlet.

Supply and Installation of 16 SWG MS/GI powder coated weather proof Earthing Box of following size with door and locking arrangement with lock and key. Box to be mounted on ISA 40x40x5 (Painted with black synthetic enamel paint) frame having 2 legs of length 800 m m (500 mm above ground and 300 mm below ground which is to be grouted with PCC 1:2:4). Bottom of box should have opening for incomin g earth GI strips all complete, as per specification and direction of Engineer-in-charge. Note: EARTHING BOX in RED should be boldly written over the box. The box should have a hood at the top extending outwards such that no water should seep through inside the bo x during rainy season to avoid rusting.

i) 450 X 300 X 250 mm

Dismantling Lights

Please Enable Macros to View BoQ information