SPECIAL REPAIRS TO BLDG NO P-525, P-522, P-527, P-524 AT SPR AQAW (A) AND OTHER SANCTIONED WORK AT LPR SQAE (A) AND SPR OF AQAW (A) KHAMARIA UNDER AGE B/R-II OF GE (EAST) JABALPUR

Amount

Taking down chowkhats or frames n.exc 1.50 sqm with shutters (without taking off shutters from the frames) complete all as specified.

Taking down chowkhats of frames exc 1.50 sqm but n.exc 4.0 sqm with shutters (without taking off shutters from the frames) complete all as specified.

Taking down shutters of any description exc 1 Sqm and n.exc 2 Sqm each and refixing in same opening after adjusting complete all as specified.

Steel windows with side hung shutters including box type hinges with steel handles, & steel peg stay, complete with glazing bars, dovetailed or welded.

Steel windows with side hung shutters including box type hinges with steel handles, & steel peg stay, complete without glazing bars, dovetailed or welded.

Framed work such as grills, gratings, etc., with ends of bar shoulder &/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; frame work of water tanks & similar work conforming to Fe 290 GDE -E-165.

Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floors.

At points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a down ward angle of 45 degree at 150mm centre to centre and sealing the same.

Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron.

M&L preparation of new steel sufaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint of approved shade over one coat of red oxide primer not otherwise described including rubbing out and cleaning rust on new steel surfaces complete all as specified and as directed by the Engineer-in-Charge.

M&L one coats of synthetic enamel paint on old steel surfaces of any description, n.exc 10 cms in width or girth, including preparation of surfaces, complete all as specified and directed.

M&L for preparing new surface of any description, not otherwise, described, over 10cm width or girth not otherwise described & applying two coat of aluminium paint as on roof surfaces complete all as specified and directed.

S&F rolled mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with & including either hooks & hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails & guides) & hanging ; also fastening & fixing complete GDE Fe410-W.

S&F mild steel, plain black sheet 1.25mm thick in wall cladding, steel gates & similar work, cut to size, holes punched; including round headed screws, clout nails or rivets & fixed to wood or steel framing with plain 40mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required.

S&F pressed steel frame made out of MS sheet 1.25mm thick of size 105 x 60 mm for doors/windows with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc including filling of concrete 1:3:6 type C-0 (12.50 mm graded aggregate) back of chowkhats and including two coats of synthentic enamel paint complete all as specified and directed.

35mm thick, 2nd class hard wood plain framed, panelled (factory made) shutters with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces, The size of rail and stile as per IS-1003 (Part-I) (Larger size to be provided) kiln seasoned and chemically pressure treated fitted to chowkats all as specified and directed.

M&L for preparation of old wood or wood based surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint.

M&L for preparation of new wood or wood based surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frames shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom railon either side and as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, supplying and fixing in the frame at site as per specification & drawing.

S&F Solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, supplying and fixing in opening as per specification and drawing.

S&F Butt hinges, heavy weight, cold rolled mild steel, 100 mm long and complete.

S&F Aluminium handles cast type anodized of 200mm complete.

M&L for preparation of old wood or wood based surfaces of any description over 10 cm width or girth and applying one coats of synthetic enamel paint complete all as specified.

S&F in repair glazing with 6 mm thick acrylic sheet fixed to iron/ wooden frame with wooden beading and screw in squares n.exc 0.5 sqm in each pane complete all as specified and as directed.

S&F 3.00 mm thick plain sheet glass, ordinary quality and glazing with oil putty in squares n.exc 0.5 Sqm in each pane.

3 mm thick sheet glass ordinary quality and glazing with oil putty or fixed with bead / glazing pins in squares size n.exc 0.5 sqm in each pane complete all as specified and directed.

Supply and fix galvanized mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples complete all as specified and directed.

S&F Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm fixed with tinned tacks, or stainless steel wire staples c omplete all as specified and directed.

S&F in repair 25mm bore Mild steel powder coated, single curtain rod (wall thickness not less than 1mm) including fancy type PVC powder coated brackets, funnels etc suitable for single curtain rod, fixed in repair, etc complete all as specified and approved by GE.

S&F 150 mm size aluminium alloy handles, febricated type extruded section, ISI marked complete all as specified.

S&F 250 mm long aluminium alloy, sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts all as specified.

S&F for aluminium anodized barrel tower bolts 125 mm of extruded section and fixed.

S&F for aluminium anodized barrel tower bolts 150 mm of extruded section and fixed.

Supply and fix MS sliding door bolts 300mm long, plate type, stove enamelled black with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed.

S&F Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy length of bolt 300mm complete all as specified and directed.

Demolitin of brick work built in cement mortar including all quions, arches, pillars etc but excluding ashlar facings dressed stonework and pre-cast concrete articles.

M&L for moulder fly ash brick work with straight or curved on plan exc 6 mtr mean radius built in CM (1:6) complete all as specified and directed.

Taking down existing loose plaster & clean rusted reinforcement and exposed concrete surface by sand blasting mechanical devices or any other estabilished methods and follwing stage complete please :- (a) Application of two coats of mineral based polymer modified corrosion inhibiting primer Colusal MK +Colusal 25. (b) Application of two component polymer based bond coat Zentrifix HB+Natufill BB2 or mortar low permeability or guinting with guniting aid. (c) Application Application of carbonation resistant, polymer modified reeady to ise fine mortar, Nafuquick +natufill BB2 or Zen-trifix F82+Nafufill BB2 Over the whole surface (Make : MC or equivalent)

Brick work with sub class'B' bricks straight or curved on plan exc 6 mtr mean radius built in CM (1:6) complete all as specified and directed.

Taking down cement plaster on brick walls or stone walls any descrition etc including raking out joints, hacking for key, scrubbing down with water etc all as specified and directed.

M&L plain cement concrete 1:2:4 type B-0 (using 12.5mm graded stone agg) as in filling under undulation of roof top/chajja/beam etc with and incl necessary formwork complete all as specified and directed.

M&L for Cement concrete type B0, 1:2:4 (12.50 mm graded aggregate) as coping , Fixing of Hold fast, benching of chajjas for filling depression and making proper slope complete all as directed.

M&L Brickwork with subclass 'B' bricks, straight or curved on plan to any radius in half brick thick walls built in CM (1:4) and as directed.

M&L Water proofing treatment on roof surface (Horizontal & Vertical surfaces) in following sequence through manufacturer / authorized applicator of the manufacturer including taking down of existing roof treatment, properly cleaning & drying the concrete surfaces complete all as specified and directed.

M&L 10 mm thick rendering on roof surfaces/concrete surface in CM 1:4 complete.

Applying a coat of oxidised bitumen based solvent primer @ 0.3 Kg / Sqm.

Applying evenly a tack coat of industrial bitumen 85/25 grade @ 1.2 kg/ Sqm incl cleaning surfaces.

Laying 3 mm thick unrolled over the bitumen coated surface, polymeric water proofing membrane Hyperplas standard weight not less than 3kg /Sqm with 100 mm over laps shall be sealed by flame as per manufacturers instruction.

Applying two coats of bituminous base aluminium paint including preparation complete.

Supplying only Integral waterproofing compound (ISI Mark) complete all as specified and directed.

M&L for rendering 15 mm thick cement plaster on fair faces of brick work or concrete surfaces in cement mortar (1:6) finished even and smooth without using extra cement complete all as specified and as directed.

Rendering 10 mm thick cement plaster on faces of brick work or concrete surfaces in cement mortar (1:3) as in ceiling finished even and fair without using extra cement all as specified and directed.

M&L Rendering 15mm thick cement plaster on fair faces of brick work or concrete surfaces in cement mortar (1:4) finished even and smooth without using extra cement complete all as specified and directed.

M&L Rendering 15mm thick on brick work or concrete surfaces of wall in CM (1:4) in two coats of 10 mm first coat (including dubbing coat finished even and smooth witout using extra cement and 5 mm final coat both coat mixed with WPC finished even & smooth without using extra lime or cement. Note : WPC shall be paid seperately under relevant item here-in-before.

Preparation of new plastered surface of external wall and chajjas and making the surface smooth with sand paper and priming the surface with alkali resistance primer paint for external surface, over primed surface applying two coat of cement base paint incl curing complete all as specified & directed.

Preparation of new plastered surface of wall by applyingone coat primer and 2 mm thick wall care putty and making the surface smooth and applying two coat of oil emulsion distemper complete all as specified & directed.

Preparation of old surface after complete removal of existing treatment applying 2 mm thick wall care putty and making the surface smooth and applying two coat of oil emulsion distemper complete all as specified & directed.

M&L three coats of white wash on surface of ceiling including preparation of new plastered surface complete all as specified and directed.

M&L two coats of white wash on surface of wall including preparation of old plastered surface complete all as secified and directed.

M&L two coats of white wash on surface of ceiling including preparation of old plastered surface complete all as secified and directed.

M&L three coats of white wash on surface of ceiling including preparation of new plastered surface complete all as specified and directed.

Preparation of new plastered surface of wall and making the surface smooth with sand paper and priming the surface with primer paint and applying two coat of Fire Resistance Paint complete all as specified & directed.

Preparation of old plastered surface of wall and making the surface smooth with sand paper and priming the surface with primer paint and applying two coat of Fire Resistance Paint complete all as specified & directed.

Preparation of old surface after complete removal of existing treatment making the surface smooth and applying two coat of cement base paint over a coat of alkali-resistant priming paint all as specified & directed.

Demolition of cement concrete (un-reinforced) in ground floors and pavings n.exc 15cm thickness (below or above ground level) complete all as directed.

Demolition of reinforced below or above ground level exc 15 cm thickness and removing rubbish to a distance exc 50m at low laying area complete all as specified and directed.

M&L Forming 12mm thick Expansion joints filled with pre-formed bituminous filler and top 30mm primed andsealed with sealing compound, Grade ‘A’.

Cement concrete type C-1, 1:3:6 (using 40mm graded stone aggregate) as in plinth protection and paving 75mm thick laid in slope finished even and fair complete all as specified.

Cement concrete type C-1, 1:3:6 (using 20mm graded stone aggregate) as in plinth protection and paving 75mm thick laid in slope finished even and fair complete all as specified.

M&L for 25mm thick PCC 1:2:4, type BO, using 12.5mm graded stone aggregate as in sub floor to receive any type of tiles complete all as specified and directed.

20-25 mm thick Kota stone slab flooring set and jointed in neat cement slurry and pointed in coloured cement to match tiles including rounding the edges of kota stone over and including 15 mm thick screed bed in cement mortar (1:6), surfaces finished even and rough to receive tiles complete all as specified and directed.

18-20 mm thick Kota stone tiles in skirting, dado etc, set and jointed in neat cement slurry and pointed in coloured cement to match tiles including rounding the edges of kota stone over and including 15 mm thick backing coat in cement mortar (1:4), surfaces finished even and rough to receive tiles complete all as specified and directed.

18-20 mm thick Kota stone tiles floors, in riser and Trades of steps, skirting, dado etc, set and jointed in neat cement slurry and pointed in coloured cement to match tiles including rounding the edges of kota stone over and including 15 mm thick backing coat in cement mortar (1:4), surfaces finished even and rough to receive tiles complete all as specified and directed.

M&L for glazed ceramic coloured tiles in vertical surface 300 x 200 x 7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match incl rendering 10mm thick in CM (1:4) and finished rough, complete all as specified & directed.

M&L for 100 mm thk PCC 1:4:8 type D-2 as in subbase to flooring.

M&L for 75 mm thk PCC 1:4:8 type D-2 as in subbase to flooring.

Taking up or down 15mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and directed.

Taking up or down 20mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and directed.

S&F 15mm bore GI tubes, 'medium grade' galvanised, with all fitting and fixed complete including cutting, chaising, pinning and making good to walls and ceiling or laid in floors.

S&F 20mm bore GI tubes, 'medium grade' galvanised, with all fitting and fixed complete including cutting, chaising, pinning and making good to walls and ceiling or laid in floors.

S&F in repair bib tap fancy type chromium plated screwed for iron pipe of 15mm bore complete all as specified and directed.

S&F in repairs Vitreous china wash basin, white flat back, size 550 x 400 mm including waste pipe, brackets and cutting for and pinning in ends of brackets or errecting stand and 32 mm dia PVC waste pipe fixed in repair including waste copling 32mm size full thread, brass, chromium plated for glazed ware sinks, basins, etc., with long screwed shanks & fly-nuts complete all as specified and directed.

S&F 15mm bore pillar cock fancy type, screwed down high pressure with or without letters hot or cold with long screwed shank and fly nuts screwed for iron pipe ISI marked add if fixed in repairs complete all as specified & directed.

S&F in repair towel rail CP 600 mm long complete all as specified and directed.

S&F in repair Vitreous China squatting pan of orissa pattern, size 580 x 440mm white with CI ‘P’ or ‘S’ trap, front or back inlet and foot rests, any pattern (including fixing of flush pipe) including provision of cement concrete bedding, in repair complete all as specified and as directed.

S&F in repair PVC flushing cistern 10 ltr capacity incl PVC connection inlet and and outlet connections, brackets, PVC flush pipe with bend 32 mm dia of suitable length including making necessary connections to water supply pipe line and jointing to WC complete all as specified and directed.

S&F in repair PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

Demolition & breaking up drain pipes (Salt glazed ware, AC or re-inforced concrete) set in CM internal dia of pipe 100 mm.

S&F PVC (SWR) pipes 75mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors.

S&F PVC (SWR) bends any radius 75mm dia.

Stop valve/Angle valve cast copper alloy (ISI Marked) chromium plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe 15mm bore dia, in reapirs complete all as specified and directed.

S&F in repair sinks made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420 mm bowl size 410 mm x 330 mm x 160 mm icl PVC waste pipe fixed in repair including waste copling 32mm size full thread complete all as specified & directed.

S&F in repair sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm (Make Nirali Model Olympia or equivalent of Prayag).

Supply & Fixing 'in repair' 18 mm thick, PVC sheet one side prelaminated of approved texture ("Celuca ply of Rajshree make or equivalent in "Sintex" as approved by GE ) as in cupboard (withshelves and partitions) as per manuacturer's instructions complete all as specified & directed.

S&F 40 mm dia brass cupboard knobs fixed with nut, screw and washer of mild steel bright complete.

S&F Mortice lock, vertical type size 100 mm 4 lever. Make - Godrej as complete all as specified and directed.

S&F Continuous (piano) hinges, mild steel, bright finish or electro galvanised.

M&L for pre polished Coloured Chequered cement concrete tiles 30 cm x 30 cm x 25 mm thick set, jointed and pointed in neat cement slurry in floors including screed bed or bedding layer of cement mortar (1:6), 15 mm thick for laying floor.

Dismantling old floor tile including cement mortar bedding and removal of debris out of premises complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick area of each tile exc 0.11 sqm but n.exc 0.18 sqm in floors etc set and jointed (joint free) in neat cement slurry and pointed in coloured cement over screed bed or bedding layers of mortars 15 mm thick in CM 1:4 for laying floor finishes complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick area of each tile exc 0.11 sqm but n.exc 0.18 sqm in skirting/dado/risers of steps etc set and jointed in neat cement slurry and pointed in coloured cement including rendering 10mm thick in CM (1:4) and finished rough, including taking down cement plaster on walls etc complete all as specified and directed.

M&L glazed ceramic coloured tiles in vertical surface 450 x 350 x 7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match including rendering 10mm thick in CM (1:4) complete all as specified and directed.

M&L 20 mm thick Granite (of any type) work (table rubbed & polished) in steps, jambs, pillars, window-cills cooking platforms & like in cement mortar (1:4) including pointing into white cement (1:2) using marble dust with admixture of pigment to match shade of granite over 15 mm thick cement screed in CM 1:4 including dismanting floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store & rubbish off the premises, complete all as specified and directed.

Round chamfering, to the edges of granite n.exc 15mm wide on granite stone shelves.

Dismantling of Asbestos cement (corrugated, semi corrugated, etc) sheets in roof coverings.

S&F prepainted galvatume aluminium zinc coating GI based corrugated steel 0.50 mm thk of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screw as in roof complete all as specified and directed.

S&F Prepainted galvatume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in ridge /cladding to wall, fixed with self tapping screws complete all aas specified.

Dismantling timber scantlings 40 sqcm & over in section, in any position.

S&F Second class Hard wood clean Sawn Timber fixed in Scantling/Purline.

Rolled sections as in main and cross beams, hip and jack rafters; purlins where onnected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates.

Demolition of RCC of any description & in any position not otherwise specifically provided for and removing rubbish to a distance exc 50m at low laying area complete all as specified and directed.

Precast Reinforced cement concrete 1:2:4 type B1 (using 20mm graded crushed stone aggregate) set in Cement Mortar (1:4) as in slab for water tank/shelf, landings, cooking plateform cover slabs (for man holes etc) chullah hoods, chajjas, water trough, managers, shelves & similar articles with plain faces.

TMT bars10 mm dia and over cut to length, bent to shape required including crancking bending and hooping ends complete all as specified and directed.

M&L RCC type B1 (1:2:4) using 20 mm graded crushed aggregate in slabs supported on walls, beams and columns in floors, roofs, landings, blaconies, canopies, deck slabs and in shelves and the like.

Machine cut cudappah stone slab 18-20 mm thick over cement screed base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete.

Dismantling wrought iron or mild steel work of any description not otherwise provided.

Steel work in tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes conforming to I.S. 1161-1979 grade St-240.

S&F wind ties for roof including securing bolts; posts & struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; similar work conforming to Fe 290 or E-165.

Dismantling Wall & ceiling boards (fiber, pulp, insulation, etc) or insulation boards /slabs/ blankets, any thickness, including cover fillets.

Material & Labour for suspended false ceiling system using Chicago metallic (E grid) exposed suspended system of gird, section size 600 mm x 600 mm comprisisng of GI powder coated main 39 mm x 24 mm x 0.80 mm thick (thickness comprising of GI / 0.40 + PPPCGS / 0.30) Cross Tee 29 mm x 24 mm x 0.80mm thick and wall angle 22.2 mm x 22.2 mm x 0.65 mm thick with and including 6 mm thick HPSC (High pressure steam cured) pre-primed and one faced painted self imposed textured designer board to be placed in the grid system duly suspended with 4 mm dia GI bar hangers fixed with steel dash fasterners from purlins of the roof with clips including provn for light fixture complete all as specified and directed. Make : EVEREST/ARMSTRONG or other equivalent make as approved.

S&F in repair 20 mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed.

Rotational moulded polyethlene water storage tanks of capacity 1000 litres three layers (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete including 20mm dia ball brass valve high pressure with polythene float and dismantling of existing PVC tank of any capacity complete all as specified & directed.

S&F Rotational moulded polyethylene water storage tanks 500 Ltrs Capacity (cylindrical vertical with closed top) hoisted & fixed in position all as specified in SSR Part-I.

S&F Ball valves 20mm bore high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe & fixed (minimum weight 20mm-210 gms).

Excavation in treanches n.exc 1.5m wide and n.exc 1.5m in depth for foundation, etc or for shafts, wells exc 10 sqm on plan and getting out any type of soil complete.

Excavation in treanches exc 1.5m in depth but n.exc 3.0 m depth for foundation, etc or for shafts, wells exc 10 sqm on plan and getting out any type of soil complete.

Returning, filling in, including spreading, levelling, watering and well ramming in layers n.exc 25 cm.

Removing excavated material n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point.

Hardcore of Broken stone/boulders gauge n.exc. 63mm, deposited, spread & levelled in layers n.exc. 15 cm thick, watered & rammed to a true surface.

PCC (1:3:6 ) type E-2 using 40mm graded crushed stone aggregate as in foundation & mass concrete.

RCC design mix M-25 using 20mm graded crushed stone aggregate in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete.

RCC design mix M-25 using 20mm graded crushed stone aggregate in Columns, pillars,butters wall , piers, posts and struts.

Use and waste rough finished surface of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter.

Use and waste rough finished surface of formwork to sides of pillars, posts, struts, piers, columns and stanchions.

M&L 20 mm Mild steel bolts purpose made with hexagonal or square head one end and screwed the other, or screwed both ends; each screwed end to be fitted with washers and one hexagonal or square nut exc 30cm long.

S&F for ISMB -200 Plate girder or single stanchions, built up of one beam or channel section with flange plates, caps, bases splices, angle brackets, cleats and other.

Plates plain channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment.

Taking down carefully aluminium point wiring (light, fan, bell, socket, power point etc.) with or without conduit, casing caping, alongwith all connected accessories such as ceiling rose, switches, sockets, switch boards, fan regulator etc complete all as specified and directed.

Taking down sub main wiring any size of two single core aluminium/copper conductor cable PVC insulated alongwith/ without conduit and accessories and removing from site, making good to disturbed surfaces of wall and floor/ceiling etc complete all as specified and directed.

Taking down carefully point wiring of any type and in any size on wooden batten/ PVC conduit including acessories such as switches, socket ceiling rose, regulators, holders and FTL fittings including making good to disturbed surfaces, matching with existing complete all as specified and directed.

Taking down main switch/ DB’s including MCB’s with board and fixture of any description and making good to disturbed surfaces of walls etc complete all as specified and directed.

Material and labour for point wiring (concealed) for light point in and including rigid non-metallic PVC heavy duty conduit, 19/20 mm dia suitable size including cutting chases for conduits, sinking for boxes for concealed conduit wiring with 1.5 sqmm FRLS PVC insulated, unsheathed, multi stranded copper conductor cable single core, 1100 volts grade with modular flush type metal boxes suitable for fixing modular switches, sockets and fan regulator etc, including PVC insulated unsheathed multi stranded copper conductor cable of 1.5 sqmm as an earth wire connected to common earth and earth dolly as per IS specification and as specified in SSR Part-I complete for one light point/fan/bell/buzzer controlled by one modular switch, 1 way 6 amps, 1 module complete all as specified and directed.

All as per srl item No. 138 here-in-before but with one 3 pin, 5 amps, socket outlet on the same board.

All as per srl item No. 138 here-in-before but with one 3 pin, 5 amps socket outlet on independent board.

All as per srl item No. 138 here-in-before but with 2.5 sqmm copper conductor cable for one 3 pin, 15 amps socket out let on independent board.

Material and labour for point wiring (concealed) in and including rigid non metallic PVC conduit, medium grade, ISI marked, 19/20 mm dia, with 1.5 sqmm FRLS PVC insulated and unsheathed, stranded copper conductor cable, single core, 1100 volts grade with cast iron pressed steel terminal boxes suitable for mounting Modular switches, sockets with Modular Cover plate including FRLS PVC insulated and unsheathed stranded copper condutor of 1.5 sqmm as continuous earth wire for one light/fan/bell point controlled by one switch and matching with the existing surface with one layer of putty over one layer of cement complete all as specified and directed.

One light / fan point controlled by one switch.

One 3 pin 5 Amp socket outlet on same board.

One 5 Amp socket outlet on independent board.

All as per srl item No. 139 here-in-before but with 4 sqmm copper conductor cable for one 3 pin, 15 amps socket out let on independent board and 4 sqmm PVC insulated multistranded copper conductor cable as continuous bearth wire complete all as specified and directed.

M&L for sub main wiring with two single core, multi stranded, PVC insulated, 1100 Volt grade, FRLS, cable with copper conductor of size 6 Sqmm in and including/drawing through through rigid non metalic PVC conduit medium grade, ISI marked, 25 mm dia for sub main wiring including continuous PVC insulated copper conductor single core earth continuity conductor of size 6 Sqmm connected common earth. Note :- 2 x 6 Sqmm conductor cable, 1 x 6 Sqmm conductor earth continuity cable & PVC conduit shall be measured as one unit length.

Supply and fix modular switch piano flush type 230/ 250 volts, 6 amps, 1 module, single pole, one way, complete all as directed.

Supply and fix modular socket outlet multi purpose 2 in 1, 2/3 pin, 6 amps, flush type, ISI marked complete all as directed.

Supply and fix switch 16 amps, flush type, ISI marked complete all as directed.

Supply and fix socket 2/3 pin combined, 6/16 amps, flush type, ISI marked complete all as directed.

Supply and fix modular MCB protected socket, sheet metal enclosures for SPN with two pin and earth plug and socket with one single pole MCB 20/25 amps complete all as directed.

S&F in repairs signle pole and neutral with two pin earth plug and socket complete with one single ple MCB 20 Amps, 215 Volt complete all as specified and directed.

S&F Ceiling rose two to three terminal PVC/polycarbonate, isolated body.

Supply and fix moudular flush type metal boxes of 2 module with brass screw cup washers complete all as directed.

Supply and fix moudular flush type metal boxes of 3 module with brass screw cup washers complete all as directed.

Supply and fix moudular flush type metal boxes of 6 module with brass screw cup washer complete all as directed.

Supply and fix moudular cover plate with grid frame of 2 module, suitable for fixing modular switches, sockets and fan regulator complete all as directed.

Supply and fix moudular cover plate with grid frame of 3 module, suitable for fix switches, sockets and fan regulator complete all as directed.

Supply and fix moudular cover plate with grid frame of 6 module suitable for fixing modular switches, sockets and fan regulator complete all as directed.

Supply and fix ceiling rose surface bakelite, three terminal complete all as directed.

Supply and fix LED lamp 9W LED bulb, 230 V with angle holder and making proper connection complete all as specified and directed.

Supply and fix LED tube light fitting 20 watts, 2000-2200 luminaire with poly carbonate LED 20 watts/ 2100 lumin tube rod with in built reflector of same make, connecting cable three core PVC insulated and PVC sheathed copper flexible cable of size 16/0. 20mm with two Nos. MS bracket on wall including hanging arrangement and necessary fixing arrangement complete all as directed.

Supply and fix in high efficiency recessed mounted 36 W LED (cool day light/natural day light) luminaire light fitting as per site requirement , with 120 lumen/watt output, opal diffuser,230 V with all connected accessories, pre-wired with 3 core flexible wire of size 1.5 sqmm, Size 595 x 595 mm connecting and testing complete all as directed.

Supply and fixing in repairs LED Bulkhead, 10 Watts, 230 Volt complete with all accessories, internally pre -wired with 3 core flexible 16/0.2 mm copper conductor cable connection.

Supply and fixing in repairs Security lighting luminaire for use with LED lamps, of capacity not less than 70 watts, 230 Volts, with high quality lenses & reflector, High grade aluminium pressure Die-Cast Housing with toughened glass cover, IP-65 class of protection, complete with control gear and all accessories fixed with 40 mm bore Light grade GI Pipe Bracket 1.2 mtr long bent to shape, fixed on wall with MS Flat Clamps, nuts & Bolts as required complete all as speciifed.

Supply and fixing in repairs Security lighting luminaire for use with LED lamps, of capacity not less than 30 watts, 230 Volts, with high quality lenses & reflector, High grade aluminium pressure Die-Cast Housing with toughened glass cover, IP-65 class of protection, complete with control gear and all accessories fixed with 25 mm bore Light grade GI Pipe Bracket 1.2 mtr long bent to shape, fixed on wall with MS Flat Clamps, nuts & Bolts as required complete all as speciifed.

Supply and fix modular stepped type electronic fan regulator flush type, two module on the existing phenolic laminated etc., as required, single pole, 240 volts, grade 350 watts, heavy duty and ISI marked complete all as directed.

Taking down existing ceilling fan/ exhaust fan/ wall fan of any size, cleaning, oiling, gresing and refixing its orignal position including replacing of check nut, bolt and quarter pin etc complete all as specified and directed.

Taking down old flood/street/bld security light upto 150 watt and refixing it after cleaning on existing angle brackets complete all as specified and directed.

Supply and fix single pole and neutral 12 Way double door Sheet metal enclosures factory made DBs protection class IP-42, suitable for fixing of MCBs conforming to IS-13032, Isolators etc with 200 Amp rated bus bar 240V powder coated painted complete all as specified and directed.

S&F single pole and neutral 8 Way double door Sheet metal enclosures factory made DBs protection class IP-42, suitable for fixing of MCBs conforming to IS-13032, 240v powder coated painted complete all as specified and directed.

Supply and fix MCB, SPN, 240 volts, 32 amps capacity, 'C' series complete all as directed.

Supply and fix MCB, SP, 240 volts, 5 to 32 amps capacity, 'C' series complete all as directed.

Supply and fixing GI steel tubing 25 mm bore, light grade, IS Marked including all fittings, laid in trenches complete all as directed.

Supply, lay and testing XLPE, insulated armoured heavy duty electric cable with stranded aluminium conductor 1100 volts grade of 10 sqmm, 2 core cross sectional area laid in trenches/ poles/ ducts/ pipes or through sleeves etc, including connecting/ jointing with lugs complete all as specified and directed.

M&L for sand cushioning to under ground cables 8 cm thick before laying the cable and 15 cm, thick after laying, stretching and testing the cable.

Supply and laying un-reinforced, precast concrete cable covers, of the size 250 x 150 x 40 mm at right angle to length of trench as protection to UG cable complete all as specified and directed.

Earthing complete for various equipments with galvanised steel earth plate electrode 600 x 600 x 6mm thick directly burried in the ground (earth pit not less than 2.25 metre deep below ground level) with top edge of earth plate not less than 1.5 m below the ground level, connected to G.I wire 4 mm by means of bolts, nuts, check nuts and washers of galvanised iron or steel, GI pipe 40mm bore light grade for protection of earthing strip, PCC chamber 1:4:8, type C-1 using 20mm graded crushed stone aggregate, internal surface of concrete chamber plastered with 12mm thick plaster in CM 1:4, funnel with wire gauge of 22 gauge ( 0.63) 8 mesh per linear inch, 50mm thick cover of RCC 1:2:4, type B-1, using 20mm graded crushed stone aggregate, reinforced with 8mm TMT bar at 100mm center to center both ways and charcoal dust and common salt all as shown in electrical plate No. 3 of MES SSR Part-I and as specified including excavation and earth work and connecting the earthing to an earthing test point as specified and testing on completion all as directed. Note:- Unit rate quoted is inclusive of earth lead and protection pipe upto 7.5 metre from earth plate.

Schedule of credit amount of Rs. 1,27,061.50 to be deducted during AOC

G S CONTRUCTIONS

TRISHLA CONSTRUCTIONS

m/s R K SETHI