SPL REPAIR TO BLDG NO 14 A AND B COMMA SPL REPAIR TO BLDG NO T 34 AND T 35 OF 17 ASSAM COMMA SPL REPAIR TO ROOF TREATMENT AT 1 RAK COMMA PROVN OF SOAK WELL AT CCPU MD ACCN AND PROVN OF FALSE CEILING OF P 2 JCO CLUB AT CCPU UNDER GE WEST LUCKNOW

Amount

Demolition of brick work or stone/ boulder masonary, built in cement mortar or cement lime mortar including all quions, arches, pillars, etc. but excluding ashlar facings, dressed stone work and precast concrete articles etc. complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness, laid, bedded and pointed in any mortar in floors, aprons etc. complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings not exc. 15 cm thickness (below or above ground level) complete all as specified and directed.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed. NOTE: Reinforcement shall be cut as required to facilitate demolition.

Dismantling of structural steel work including doors, gates, wind tie etc., but excluding framed trusses etc. complete all as specified and directed.

Dismantling of structural steel work as in framed trusses not exceeding 10m span complete all as specified and directed.

Excavating in trenches n.exc 1.5m wide and n.exc 1.5m in depth for foundation etc or for shafts, wells, cesspits, manholes, pier holes etc n.exc 10 sqm on plan and n.exc 1.5m in depth and getting out in soft/ loose soil complete all as specified and directed.

Returning, filling in, trenches including spreading, levelling, watering and well ramming in layers not exc. 25cm in soft/ loose soil complete all as specified and directed.

Removing surplus excavated material soils n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and directed.

M&L for hardcore of broken stone or boulders of gauge not exc 63mm, deposited, spread and levelled in layers n.exc 15cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for brick work with old size fly ash bricks of class designation 75, straight or curved on plan exceeding 6m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for brick work with old size fly ash bricks of class designation 75, straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4 complete all as specified and directed.

M&L Cement Concrete 1:2:4 type B-1 using 20mm graded stone aggregate as in lintels upto 1.5m clear span, cills, steps, seismic and other bands, plinth courses, string cources, lacing cources, parapets and railing upto 60cm in hight, copings, kneelers, apex stones, bed plates, water troughs, hold fasts and the like including weathering, slightly rounded or chamfered angles and throating including necessary formwork complete all as specified and directed.

M&L Mild Steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) area n. exc 1.50 Sqm each complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) area exc 1.50 Sqm but n. exc 4sqm each complete all as specified and directed.

S&F pressed steel door frame of size 125x60mm with one or more rebates, made out of 1.25mm thick MS sheets including necessary fixing lugs, hinges, lock strike plate, etc. complete as specified and fixed including one shop coat of primer complete all as specified and directed.

M&L cement concrete 1:3:6 type C-0 using 12.50mm graded stone aggregate as in filling and mass concrete to back of pressed steel frame complete all as specified and directed.

S&F 35mm thick factory made 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc, (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut or mitred beads for securing glass, gauge etc sizes of members of shutters as specified in SSR Part-I Section 8 clause 8.24(a) and fitted to chowkats complete all as specified and directed.

S&F 35mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc, divided into squares, with plain, chamfered or rounded, metred and rebated shash bars, any numbers, edges of framing plain, chamfered or rounded, fitted with cut or mitred beads for securing glass, gauge etc sizes of members of shutters as specified in SSR Part-I Section 8 clause 8.24(a) and fitted to chowkats complete all as specified and directed.

S&F flush shutters 30 mm thick, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F 35mm thick factory made 2nd class hard wood rail and style type plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P commercial ply or 12 mm veneered particle board with commercial venneering on both faces, the size of rail and stile as per IS: 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F factory made Solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet, reinforced with MS square tube, supplying and fixing in opening with fittings as per specification & drawing complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for Top & bottom rails, MS frame shall be covered with heat molded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, Panelling of plain colour PVC sheet to be fitted in the MS frame welded/ sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement and fixing in frame at site as per specification & drawing complete all as specified and directed.

S&F 100mm size butt hinges, medium weight, cold rolled, mild steel and fixed with screws complete all as specified and directed.

S&F 75mm size butt hinges, medium weight, cold rolled, mild steel and fixed with screws complete all as specified and directed.

S&F 150mm size extruded aluminum alloy handles, fabricated type, anodised complete all as specified and directed.

S&F 125mm size extruded aluminum alloy handles, fabricated type, anodised complete all as specified and directed.

S&F 200mm long Aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F 150mm long Aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed.

S&F in repair 300mm long, mild steel, ordinary rat tail rod pattern springs including including roller and roller plate complete all as specified and directed.

S&F in repair floor door stopper of aluminium alloy body and tongue, anodized, with hard drawn steel spring, fixed in floor, overall length of cover plate 150mm complete all as specified and directed.

S&F in repair 0.56mm thick plain Aluminium sheeting, Alloy 31000 H4, fixed with nails to wooden frame work complete all as specified and directed.

M&L for 4mm thick sheet glass, ordinary quality and glazing with oil putty or wooden beads in square, area n.exc 0.5 Sqm in each pane complete all as specified and directed.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F steel windows or ventilators, fixed type, complete with glazing bars dovetailed or welded complete all as specified and directed.

S&F Box type steel windows/ventilators with side hung shutters with glazed and gauzed double panel shutters both provisions including box type hinges or factory made butt hinges with steel handle, tower bolts, hold fasts and steel peg stays etc. complete with glazing bars dovetailed or welded and 10mm square guard bars @ 125mm c/c complete as per CELZ drg No. LZ/C-TD/130 sheet No 1/4 to 4/4 complete all as specified and directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/ slabs/ blankets, any thickness, including cover fillets complete all as specified and directed.

S&F false ceiling with 4mm thick 'E' Board (Make: Everest) of size 600x600mm, white, prelaminated sheet embossed reinforced designer ceiling board tiles of approved texture and powder coated, hot dipped GI imposed grid frame work complete all as specified and directed including all necessary drilling, cutting to fix electrical items as under with the following:- (a) 24x24x0.45mm thick powder coated GI angle plugged @ 600mm c/c along perimeter of wall. (b) 24x32x0.33mm thick powder coated GI tee as main and cross runners suspended with 4mm dia GI wire suspenders with adjustable clamps and dash free fastners with rawl plug and screws plugging in RCC slab etc. placed @ 600mm c/c from perimeter of wall. (c) Fixing of 4mm thick 'E' board tiles and finished complete with one coat of oil emulsion distemper on ceiling. NOTE: The complete ceiling work shall be executed as per manufacturer's instructions and as directed.

Dismantling of Asbestos cement (corrugated, semicorrugated etc.) sheets in roof coverings complete all as specified and directed.

S&F multi-rib TM profile, tensile strength 550 Mpa, colour coated 0.50mm thick pre-painted galvalume aluminium zinc coated GI based corrugated steel sheet, having maximum pitch of 250mm c/c and minimum 30mm crest depth in length as per site requirement, the feed material manufactured out of 0.50mm (TCT) with coating of 18-20 microns top coat over 5 microns primer and 8-10mm alkaline back of zinc aluminium alloy of AZ-150, including the sheet shall have a hot dip metallic zinc aluminium alloy coating of zinc 43.5%, aluminium 55% and silicon 1.5% with total mass coating of 150 gms/sqm on both sides having covered width 1020mm and return leg for proper side lap as in roof covering/ cladding and fixed with self tapping screws with EDPM seal complete all as specified and directed.

S&F multi-rib TM profile, tensile strength 550 Mpa, colour coated 0.50mm thick pre-painted galvalume aluminium zinc coated GI based plain steel sheet, having maximum pitch of 250mm c/c and minimum 30mm crest depth in length as per site requirement, the feed material manufactured out of 0.50mm (TCT) with coating of 18-20 microns top coat over 5 microns primer and 8-10mm alkaline back of zinc aluminium alloy of AZ-150, including the sheet shall have a hot dip metallic zinc aluminium alloy coating of zinc 43.5%, aluminium 55% and silicon 1.5% with total mass coating of 150 gms/sqm on both sides having covered width 1020mm and return leg for proper side lap as in roof covering/ cladding and fixed with self tapping screws with EDPM seal complete all as specified and directed.

M&L mild steel work as in bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required, hooks (stay), heavy, for large gates, hook and pintel hinges, large hasps and staples, chains, hand made sliding bolts, clamps, hold fasts, wall ties, hooks for hanging fans, plain angle cleats for securing purlins to wood trusses or rafters, knee piece inserts, two way and three way straps, plate washers and similar small articles conforming to Fe-290, Gde E-165 complete all as specified and directed.

M&L structural steel work with rolled mild steel sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates etc and similar articles conforming to Fe-410W (Gde E-250) quality-A complete all as specified and directed.

Taking down cement or cement lime plaster any description from walls/ceiling etc including racking out joints, hacking for key & scrubbing down with water all as specified and directed.

M&L for rendering 15mm thick in CM 1:6 on fair faces of brick work or concrete surfaces of wall and finished surface even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick in CM 1:4 with integral water proofing compound @ 3% by weight of cement on fair faces of brick work or concrete surface of wall and finished surface even and smooth without using extra cement complete all as specified and directed. NOTE: WPC shall be measured and paid seperately under respective item.

Supply only integral waterproofing compound complete all as specified and directed.

M&L for two coats of oil bound distemper over one coat of primer and 1mm thick layer of wall care putty on newly plastered surfaces of wall including preparation of surfaces complete all as specified and directed.

M&L for two coats of cement base paint over one coat of primer on newly plastered surfaces of wall including preparation of surfaces complete all as specified and directed.

M&L for two coats of exterior emulsion weather proof paint over one coat of primer and 1mm thick layer of wall care putty on newly plastered surfaces of wall including preparation of surfaces complete all as specified and directed.

M&L for preparation of new or previously untreated surfaces of wood or wood based materials of any description over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparation of new or previously untreated surfaces of steel or iron of any description over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for preparation of old or previously treated surfaces of wood or wood based materials of any description over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint complete all as specified and directed.

M&L for preparation of old or previously treated surfaces of steel or iron of any description over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint complete all as specified and directed.

M&L for 40mm thick cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate as in floor, finished surface even and smooth without using extra cement complete all as specified and directed.

M&L for 75mm thick cement concrete 1:3:6 type C-2 using 40mm graded stone aggregate as in plinth protection, laid in panels, finished surface even and smooth without using extra cement and forming 12mm wide expansion joints to the full depth, and filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade 'A' complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for joint free glazed ceramic tiles, coloured, superior quality of size 350x250x7mm/ 450x350x7mm thick, in vertical surfaces etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed.

M&L for joint free non skid ceramic tiles, coloured, superior quality, 7 to 8mm thick, (square/ rectangular), area of each tiles exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layer in cement mortar 1:6 complete all as specified and directed.

M&L for joint free non skid ceramic tiles, coloured, superior quality, 7 to 8mm thick, (square/ rectangular), area of each tiles exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layer in cement mortar 1:6 complete all as specified and directed.

M&L for joint free non skid ceramic tiles, coloured, superior quality, 7 to 8mm thick, (square/ rectangular), area of each tiles exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in vertical surfaces etc., set & jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed.

M&L 20-25mm thick Machine cut kota stone slab flooring, machine cut and polished as in floor over and including 20mm thick rendering in cement mortar 1:6, laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing including making moulding/ rounding to edges of stone complete all as specified and directed.

M&L 20-25mm thick Machine cut kota stone slab flooring, machine cut and polished as in vertical surfaces over and including 10mm thick rendering in cement mortar 1:4, laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing including making moulding/rounding to edges of stone complete all as specified and directed.

M&L 18-20 mm thick granite stone slab, machine cut and polished as in shelves, cooking platform etc., bedded and jointed with grey cement slurry and pointed with white cement (1:2) using marble dust with admixture of pigment to match the shade of granite stone, laid over and including 20mm thick screed bed in cement mortar 1:4, including rubbing, rubbing, grinding, making hole for gas pipe line and including making sandwitch moulding to edges complete all as specified and directed.

M&L 100mm thick cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate as in sub bases of floors and pavings etc. finished even and fair without using extra cement complete all as specified and directed.

M&L for 60mm thick M-35 grade rubber moulded factory made machine pressed precast concrete interlocking paver block any shape and size conforming to IS 15658-2006 with grey cement and pigment as approved laid over and including 25mm thick sand cushion and joints filled with sand complete all as specified and directed.

S&F Exterior finish floor tiles of size 300x300x25 mm thick, superior quality, approved shade, set and jointed in neat cement slurry and pointed in white or coloured cement to match as in floor including 15mm thick screed bed in cement mortar 1:4 complete all as specified and directed. Make: Endura/ Duracrete/ Naveen/ Eurocon/ NITCO.

M&L Continuous brick edging using old size sub class 'B' bricks, with width equal to the depth of brick, laid dry, on edge complete all as specified and directed.

Cutting chases, pinning in, for concealed water tubing etc. in brick walls and making good to disturbed surface in cement mortar 1:3, cutting not exceeding 10cm in girth complete all as specified and directed.

Taking up or down 15mm bore pipes steel tubing and connections including cleaning for refixing or removing to store or removing from site complete all as specified and directed.

Taking up or down 20mm bore pipes steel tubing and connections including cleaning for refixing or removing to store or removing from site complete all as specified and directed.

S&F 15mm bore Steel water tubing 'medium grade', galvanised with all fittings like elbow, tee, socket, bend etc and fixed to wall, ceiling or laid in floors complete all as specified and directed.

S&F 20mm bore Steel water tubing 'medium grade', galvanised with all fittings like elbow, tee, socket, bend etc and fixed to wall, ceiling or laid in floors complete all as specified and directed.

Dismantling of water tanks of capacity exc. 250 litres and not exc. 500 litres of any type and in any position and removing from site complete all as specified and directed.

Dismantling of water tanks of capacity exc. 500 litres and not exc. 1000 litres of any type and in any position and removing from site complete all as specified and directed.

S&F 500 litres capacity rotational molded polyethylene water storage tanks (cylindrical vertical with closed top), hoisted and fixed in position complete all as specified in SSR Part-I and directed.

S&F 1000 litres capacity rotational molded polyethylene water storage tanks (cylindrical vertical with closed top), hoisted and fixed in position complete all as specified in SSR Part-I and directed.

S&F ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe or brass ferrule and fixed suitable for 20mm bore pipe (Min weight 210gms) complete all as specified and directed.

S&F in repair Vitreous China wash down water closet pan, pedestal pattern, white, with 'P' or 'S' trap, excluding flushing cistern and flush pipe, including connection to drain pipe (or outgoing pipe) and to flushing pipe etc. and making good to floor complete all as specified and directed.

S&F in repair plastic water closet seat cover, white, closed pattern with flat bottom and cover, fixed with MS chromium plated or aluminium hinging device ISI marked as approved complete all as specified and directed.

S&F in repair Vitreous China squatting pan, 'Orissa pattern', size 580x440mm, white, with integral foot rests including PVC 'P' or 'S' trap, excluding flushing cistern and flush pipe, including connection to trap and flushing pipe etc. and making good to floor complete all as specified and directed.

S&F in repair PVC valveless, syphonic action type, low level, flushing cistern of 10 lit capacity, white, with inlet, ball valve, float valve and handle including bracket, rubber cone and flush pipe etc. and connection to pipes complete all as specified and directed.

S&F in repair vitreous china Wash basin, white, flat back type of size 550x400mm including CP waste coupling and 32mm dia waste pipe and fixing of 02 nos brackets made out of 40x40x5mm MS angle iron etc. complete all as specified and directed.

S&F in repair bib taps 15mm bore, half/quarter turn, fancy type, long body, cast copper alloy, chromium plated, screwed for iron pipe or for brass ferrule including all accessories complete all as specified and directed.

S&F in repair angle valves 15mm bore, fancy type, cast copper alloy, chromium plated with long shank and cup screwed down, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F in repair 15mm bore PVC connections, superior quality, with CP brass nuts of length 450mm complete all as specified and directed.

S&F in repair stop valves concealed type 15mm bore, fancy type, cast copper alloy, chromium plated with long shank and cup screwed down, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F in repair central hole basin mixer, fancy type, brass chromium plated, with round spout with popup waste system, including plugging and fixed, suitable for 15mm bore pipe complete all as specified and directed.

S&F in repair CP brass tubular towel rail 20mm dia, 'D' type, 600mm long between flanges, superior quality, fancy type, fixed to wall with PVC gully and CP brass screws complete all as specified and directed.

S&F in repair 25mm dia mild steel PVC coated curtain rod, superior quality, any colour, with end brackets and end knobs and fixed to wall with wooden plug/ PVC gully with CP screws and cup washers complete all as specified and directed.

S&F in reapir kitchen sink with drainage board made of stainless steel 1mm thick with plugs, washers, waste coupling and waste pipe, including bedding in cement mortar 1:3 to dwarf wall or fixing cantilever brackets and connecting union to waste pipe, overall size 915mmx460mm with bowl size 410x330x160mm complete all as specified and directed.

S&F in reapir stainless steel kitchen plate rack (utensil rack) of size 900x750x250mm, made out of 0.8mm thick stainless steel sheet, approved design and fixed to wall with brass screws and PVC gully including all necessary fittings like nuts and bolts etc complete all as specified and directed.

S&F in repair cast iron Nahani trap, with grating including jointing to waste pipes, fixed in cement concrete 1:2:4 type B-1 and suitable for 100mm bore pipe complete all as specified and directed.

S&F in repair 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to walls with PVC clamp complete all as specified and directed.

S&F PVC (SWR) bends of any radius, suitable for 110mm bore PVC pipes, fixed and jointed with solvent complete all as specified and directed.

M&L for 200mm bore reinforced concrete drain pipes, class NP2 complete with collars, laid and jointed in cement mortar 1:1 as in drains and similar works complete all as specified and directed. NOTE: Excavation and earthwoth with cutting existing manhole and making good shall be measured and paid seperately under respective item.

M&L for cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate as in concrete foundation bed to 200mm bore drain pipes including packing under and haunching against the sides of pipes after they are laid and tested complete all as specified and directed.

M&L cutting into existing manholes for connecting new drains, making good to 200mm bore pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required complete all as specified and directed.

M&L 10mm thick screed bed or bedding layer in CM 1:4 using 100% coarse sand over roof slab, finished surface even and smooth without using extra cement and mixed with liquid water proofing compound complete all as specified and directed. NOTE: (i) Liquid WPC shall be measured and paid seperately under respective item. (ii) Wherever screed bed shall be provided, padding shall not be provided.

Supply only Liquid waterproofing compound complete all as specified and directed.

M&L for provn of roof treatment with polymeric water proofing membrane all as given below:- (a) Taking down existing water proofing treatment and cleaning of roof surface by washing and rubbing etc. and removing the material retrieved to a distance not exceeding 500m where directed. (b) Applying a coat of bituminous primer conforming to IS: 3384-1986 @ 0.25 Iit/sqm on prepared surface and allowed to dry. (c) Applying and laying 3mm thick APP membrane having non woven polyester matt at core and covered with high quality polymeric asphaltic protected thermo fusible HMHDPE film on both sides with over laps 10cm and 15 cm at longitudinal and transverse direction respectively and sealed by flame, sealing all overlaps complete including treatment at all junctions and corners. The membrane shall be torched into groove on vertical plane and groove sealed with cement mortar 1:3. (d) M&L for applying two coats of aluminium paint on membrane @ 0.10 Kg/Sqm (each coat) complete all as specified and directed.

All as per item no. 105 above but water proofing treatment work on vertical surfaces.

M&L construction of Soakage Well of size 3.00m dia, 6.00m effective depth and 7.50m overall depth with fly ash bricks and RCC M-25 Design Mix (using 20 mm graded stone aggregate) as in cover slab etc. including all required earthwork in soft/loose soil, filling of brick bats and cement concrete etc. complete all as shown on CELZ drawing No. TD/576 sheet 1/2 & 2/2 dated 16.06.1989 complete all as specified and directed.

Taking down copper/ aluminium point wiring (light, fan, socket or power) complete including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc. removing materials to store for keeping in safe custody or for taking credit and making good disturbed surfaces of walls, floors etc. to match the existing complete all as specified and directed. NOTE: Credit for this items shall be made as per conditions separately.

Taking down carefully main switches, DB's, MCB DB's of any way or rating and making good the disturbed surfaces of walls complete all as specified and directed.

M&L for point wiring complete for one light point or one fan point controlled by one, one way 5 Amp switch with PVC (FRLS) insulated unsheathed multistranded copper conductor of size 1.50 sqmm nominal cross sectional area single core drawn in and including 20mm dia 'medium grade' PVC concealed conduits ISI marked and fittings, including pressed steel concealed terminal switch boxes not less than 1.6mm thick of reqd size factory made duly painted inside and outside with one coat red oxide primer, 3mm thick plastic laminated bakelite sheet top cover (ISI Marked) fitted with chromium plated brass screws & washers complete including 1.50 sqmm nominal cross sectional area PVC(FRLS) insulated unsheathed multistranded copper conductor green as earth wire connected to earth dolly with all accessories complete all as specified and directed.

All as per item no 110 above but for one 6 pin 15/16 amps socket outlet point on an independent board with cables of size 2.50sqmm and green colour earth cable of size 2.50sqmm.

S&F Switch piano, flush type, single pole, one way 5/6 Amp 230 Volts complete all as specified and directed.

S&F Switch piano, flush type, single pole, one way 15/16 Amp 230 Volts complete all as specified and directed.

S&F socket outlet, flush type, single pole, multipurpose 2 in 1, 5 pin 5/6 Amp, 230 volts complete all as specified and directed.

S&F socket outlet, flush type, single pole, multipurpose 2 in 1, 5 pin 15/16 Amp, 230 volts complete all as specified and directed.

S&F ceiling rose, 3 terminal, PVC/ Polycarbonate, insulated body, surface bakelite sheet 63.50mm dia complete all as specified and directed.

S&F Lamp holder PVC/ Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

S&F sheet metal enclosure for MCB DB double door type, single pole and neutral 4 way, 240Volts with 100/125 Amps rated bus bar of suitable size plate and common neutral link, epoxy powder coated, factory made complete without MCB and with enclosure blank plates for unused way complete all as specified and directed.

S&F MCB, single pole 6 to 32 Amp, 240 volts, 10 KA breaking capacity, 'C' curve complete all as specified and directed.

S&F MCB, single pole & neutral 40 to 63 Amp, 240 volts, 10 KA breaking capacity, 'C' curve complete all as specified and directed.

Taking down old copper/ aluminium sub main wiring or service connection complete all as specified and directed

S&F sub main wiring with two single core PVC insulated (FRLS) unsheathed multistranded copper conductor of size 4sqmm nominal cross sectional area and one run of 4sqmm nominal cross sectional area PVC insulated (FRLS) unsheathed multistranded copper conductor green colour as continuous earth wire drawn in and including 25mm dia 'medium grade' PVC concealed conduits (ISI marked) and fittings complete all as specified and directed. NOTE:- One unit length shall measured as two run of main wire and one run of conduit & earth wire.

S&F in repair wall mounted 18/20 W LED integrated tube light fitting of size 1200mm long batten with extruded aluminium housing, frosted diffuser and integrated electronic driver with decorative end cap complete and one no 18/20 W LED 6000 K, 230V, complete with all required fittings and fixtures arrangement including and provn of connection from ceiling rose to luminaries with PVC 3 core flexible copper wire complete all as specified and directed. Make: Havells cat no. LUMILINE PLUS BS 20WLED865SPCSS or Surya Visco cat no. SLEBT 20IL or C&S Nakshtra series cat no. LTTB4F20WLED/W.

S&F in repair security light fitting of 25 W LED 6000 K, with high power LED source (more than 100 lumens/ watt), PDC housing, IP65 with 4KV inbuilt surge protection driver and one no. 25W LED tube, with all accessories, prewired with and fixed to bldg/pole including GI bracket 1.20m long bent to shape, made out of 40mm dia GI light grade pipe with nuts, bolts and washers and provn of connection from ceiling rose to luminaries with PVC 3 core flexible copper wire complete all as specified and directed. Make: Havells cat no. LHEWEBP7PL6S025 or Surya cat no. LEXON SLE UL 25W IP66 or C&S (Indus E series) cat no. LTESS25WLED/L5.

M&L Earthing complete with galvanised steel earth plate electrode 600x600x6mm thick, burried directly in ground (earth pit not less than 2.25m deep below ground level) with top edge of the plate not less than 1.5m deep below normal ground level, connected to galvanised earth lead wire 4.0mm dia (7.50m) by means of bolts, nuts, check nuts & washers of galvanised iron or steel, earth lead wire protected by 15mm dia GI pipe light grade, 20mm dia light grade GI pipe for watering, meshed funnel, alternate layer of charcoal and common salt complete all as SSR Item No. 19471 and shown in electrical plate No. 3 of SSR part-I with PCC chamber, 50mm thick RCC cover in 1:2:4 type B-1 using 20mm graded stone aggregate reinforced with 8mm dia TMT bar @ 80mm c/c both way in lieu of CI pit cover and protection including necessary excavation and earth work complete all as specified and directed.

M&L for sand filling under floors or in foundatoins as in sand cushioning including spreading, levelling, watering and well ramming complete all as specified and directed.

Supplying & laying sub class 'B' bricks old size over LT/HT cable laid flat for protection of cable complete all as specified and directed.

M&L 40mm bore GI tubing light grade including necessary fittings laid in trenches, under road crossing, fixed on poles, walls, under floors etc complete all as specified and directed.

S&F in repair 1100V grade heavy duty XLPE armoured cable, PVC insulated aluminium stranded conductor served with inner sheathing of PVC tape and overall PVC sheathed in service connection of size 10sqmm, 2 core cable complete all as specified and directed.

S&F heavy duty metal body exhaust fan 300mm sweep, copper wound, 1400 RPM, AC single phase, 230/240 volts, fancy type complete with fan motor, blade, bracket, ring and louvers including and provn of grouting 4 nos anchor bolts with nut and washer and making good to disturbed surfaces to match the existing and provn of connection with with three core flexible copper wire cable of size 1.50sqmm from ceiling rose to fan complete all as specified and directed. Make: Orient (Heavy duty)/ Usha (Turbo heavy duty metal body)/ Havells (Turbo Force HP)/ Khaitan (heavy duty metal body).

Cutting and opening of circular holes in shape in one brick thick walls built in cement mortar for fixing of exhaust fan up to 300mm dia and making good dismantled portion in CM 1:3 or PCC 1:2:4 type B-1 using 20mm graded stone aggregate including and provn of fixing of 4 nos anchor bolts with nut and washer to fix the exhaust fan complete all as specified and directed.

S&F in replacement storage type water heater (geyser) of capacity 25 litres, electric driven, BEE five star rated, AC 230 volt, vertical type and provn of fixing arrangement with 4Nos fastener of size 100x10 mm with washer and bolts and making water connection with 02 nos 450mm long flexible pipe and 16 Amp plug top complete all as specified and directed. Make: Havells/ Crompton/ Usha/ Jaquar. NOTE: Old geyser shall be deposited at E/M store yard.

chandra kaushal supplier

M/S S S A ASSOCIATES

M/S Chandra Mohan and Sons