COMPREHENSIVE REPAIR TO OFFICERS MD ACCN AT TARAPORE ENCLAVE UNDER AGE B/R-II OF GE (SOUTH) DELHI CANTT-10

Amount

Taking down cement or cement lime plaster or Grit plaster any description, on brick or stone walls, concrete surface etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed.

M&L for rendeing 15 mm thick on brick/concrete masonary surface other then fair faces surfaces in CM 1:4 finished even and smooth without using extra cement including necessary scaffolding, formwork, safety precautions for multi storey bldgs (upto G+4) complete all as specified and as directed.

M&L for rendeing 15mm thick on brick/concrete masonary surface other then fair faces surfaces in CM 1:6 finished even and smooth without using extra cement including necessary scaffolding, formwork, safety precautions for multi storey bldgs (upto G+4) complete all as specified and as directed.

M&L for rendeing 5mm thick on ceiling surfaces in cement mortar 1:3 finished even and smooth without using extra cement including necessary scaffolding, formwork, safety precautions for multi storey bldgs (upto G+4) complete all as specified and as directed.

M&L for rendeing 15mm thick on brick/concrete masonary surface in patches work area upto and including 3 sqm other then fair faces surfaces in cement mortar 1:6 finished even and smooth without using extra cement including necessary scaffolding, formwork, safety precautions for multi storey bldgs (upto G+4) complete all as specified and as directed.

M&L for complete removal of existing treatment from internal surfaces of walls or a part thereof (In Patches ), area exceeding 3.00 Sqm but not exceeding 5.00 Sqm , which is damage due to seepage or any other reason & preparing and levelling the disturbed surfaces by using wall care putty (JK/Birla white) to obtain even and smooth wall surfaces of that portion and using sand paper and than applying two coats of oil bound distemper over a coat of primer, including scaffolding arrangement, trestles, ladders safety precautions for multi storey bldgs (upto G+4) complete all as specified and as directed.

M&L for washed stone grit plaster on exterior walls in two layers, under layer 12 mm cement plaster 1:4 ( 1 cement : 4 coarse sand) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 kg of cement per square metre, top layer 15 mm cement plaster 1:1/2:2 (1 cement : 1/2 coarse sand : 2 stone chipping 10 mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings complete all as specified. Notes :- (i) The work will be carried out upto (G+4) storey in Patches (ii) All necessary scaffolding,trestles, ladders arrangement will be provide by the contractor. The rates may be included in the respective items. Construction Safety net will be provide by the contractor during execution of the work as directed.

M&L for forming groove of uniform size 25mm wide and 15mm deep in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repair to the edges of panels and finishing the groove with safety precautions for multi storey bldgs (upto G+4) complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of wall and applying 1 to 2 mm thick wall care putty on whole surfaces to achieve smooth, even and uniform surface including grinding with sand paper and levelling of surface and applying two coat of oil bound distemper over a coat of primer of same manufacturer on white or tinted over existing prepared putty base surface with safety precautions for multi storey bldgs (upto G+4),complete all as specified and as directed. Notes :- (a) All work shall be done mechanically through authorised applicator only (b) Authorised applicator of paint manufactures shall have valid authorisation letter from the manufacturer (minimum regional HQs) issued not earlier than 30 Days from start date of the said finishing work. (c) The contractor shall provide application testing and certification of finishes by paint manufacturing firm/their authorised applicator. (d) Cost of all above aspects shall be deemed to be included in quoted rate of the contractor.

M&L for preparation of newly plasered surfaces of walls and applying two coat of super quality weather proof exterior emulsion paint over and including one coat of primer from the same manufacturer on external wall / ceiling surfaces including a coat of 1 to 2 mm thick wall care putty to achieve smooth surface,complete all as specified and as directed. Notes :- (a) All work shall be done mechanically through authorised applicator only (b) Authorised applicator of paint manufactures shall have valid authorisation letter from the manufacturer (minimum regional HQs) issued not earlier than 30 Days from start date of the said finishing work. (c) The contractor shall provide application testing and certification of finishes by paint manufacturing firm/their authorised applicator. (d) Cost of all above aspects shall be deemed to be included in quoted rate of the contractor.

M&L for preparation of newly plasered surfaces of ceiling and applying three coat of white wash, complete all as specified and as directed.

Complete removal of existing loose treatment by scraping with mechanical wall/ ceiling by vacum based sanding machine (sanding machine with internal dust extraction system & having mechanical vacuum mechanism) having RPM not less than 1500, sanding pad of 80 grit having dia of 7 inches / 9 inches to make the surfaces free from dust, loose paint etc by using smart periodical methodology and applying two coats of distemper oil emulsion, with Graco spray machine on wall/ ceilling surface white or tinted over one coat of primer with and including 1 to 2 mm thick wall care putty to prepare the surface even and smooth for multi storey bldgs (upto G+4) complete all as specified and as directed.

Complete removal of existing loose treatment by scraping with mechanical wall/ ceiling by vacuum based sanding machine (sanding machine with internal dust extraction system & having mechanical vacuum mechanism) having RPM not less than 1500, sanding pad of 80 grit having dia of 7 inches / 9 inches to make the surfaces free from dust, loose paint etc by using smart periodical methodology and applying two coats of GreenPro certified water-based, modified acrylic, exterior Apex Suprema Emulsion or equivalent as per required shade (Company depot tinted) with silicon additives, heat reflectant property, VOC less than 2% by mass, Class A IS-15489 and IS-101 @5-6 sqm/ltr with Graco-490 spray machine over one coat of primer with and including 1 to 2 mm thick wall care putty to prepare the surface even and smooth with safety precautions for multi storey bldgs (upto G+4) complete all as specified and as directed.

M&L for preparation of old surface of ceiling and applying one coats of white wash complete all as specified and as directed.

M&L for preparation of old surfaces of wall and applying one coats of white wash complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

M&L for vitrified light shade ceramic tiles 9-10 mm thick(square/rectangular) polished, area of each tile not exceeding 0.36 sqm, as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match ver and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and as directed.

M&L for vitrified light shade ceramic tiles 9-10 mm thick square/rectangular) polished, area of each tile not exceeding 0.36 sqm, as in skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick backing coat in cement mortar 1:4 complete all as specified and as directed.

M&L for non-skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match,including 15mm thick screed bed in cement mortar 1:6, complete all as specified and as directed.

M&L for 7 to 8 mm thick Glazed Ceramic coloured tiles in vertical surface area exc. 0.11 Sqm each but 0.18 Sqm each set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10mm thick backing coat of cement mortar 1:4, complete all as specified and directed.

M&L for non-skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm as in Patches work area upto and including 1.5 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of existing tile over and including 15mm thick screed bed in cement mortar 1:6, complete all as specified and as directed.

M&L for joint free glazed ceramic coloured tiles in patches work upto and including 1.5 sqm in vertical surface 450x350x7/450x300x7/ 300x200x7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10mm thick backing coat in cement mortar 1:4 complete all as specified and as directed.

Dismantling stone slabs and tiles of any discription or thickness in floors, aprons etc, laid bedded and pointed in any mortar complete all as specified and as directed.

M&L for granite (of any type any colour as directed) work, 18-20 mm thk (table rubbed and polished) in steps,jambs,pillars, window-cills, cooking platforms and like in 20mm thick screed bed cement screed bed in cement mortar 1:6 including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed.

M&L for Udaipur green marble work 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms, cubboard vertical face with screws etc, and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade including 20mm thick screed bed in cement mortar 1:6 complete all as specified and as directed.

M&L for machine cut kota stone slab flooring 18-20mm thick over and including 20mm thick screed bed in cement mortar 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete all as specified and as directed.

Rounding to edges of stone slabs one edge such as in steps cooking platform and other similar situations complete all as specified and as directed.

Taking up or down steel tubing and connections, 15 mm bore of pipe complete all as specified and as directed.

All as per item No 28.00 here-in-before but 20 mm bore of pipe complete all as specified and as directed.

All as per item No 28.00 here-in-before butt 25 mm bore of pipe complete all as specified and as directed.

M&L supplying and fixing of 15 mm bore CPVC pipes SDR 11 & plain CPVC SCH-40 fitting on walls /ceiling or laying in floors including all fitting such as ( brass elbow, Brass Tee, Male threaded brass adaptor, Female threaded adaptor etc) union ,ball valves, flange and tank adaptor complete all specified and directed.

All as per item No 31.00 here-in-before but 20 mm bore of pipe.

All as per item No 28.00 here-in-before but 25 mm bore of pipe.

S&F in repair for rotational moulded polythylene water storage tanks 250 litres capacity (Rectangular with closed top) hoisted and fixed in position complete all as specified in SSR-I including brass valve high pressure with polythne float and fly nut complete, screwd for iron pipe or brass ferrule size 25 mm bore including dismantling of water tanks of any type/pattern and removing from site complete all as specified and as directed.

S&F in repairs HDPE PVC lid (cover) for 250 Litres capacity PVC tanks complete all as specified and as directed.

S&F in repair for rotational moulded polythylene water storage tanks 300 litres capacity (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified in SSR-I including brass valve high pressure with polythne float and fly nut complete, screwd for iron pipe or brass ferrule size 25 mm bore including dismantling of water tanks of any type/pattern not exc 300 ltr and removing from site of work complete all as specified and as directed.

S&F in repair for rotational moulded polythylene water storage tanks 1000 litres capacity (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified in SSR-I including brass valve high pressure with polythne float and fly nut complete, screwd for iron pipe or brass ferrule size 25 mm bore including dismantling of water tanks of any type/pattern not exc 1000 ltr and removing from site of work, complete all as specified and as directed.

S&F in repairs HDPE PVC lid (cover) for 300 to 1000 Litres capacity PVC tanks complete all as specified and as directed.

S&F in repair Ball valves, high pressure, with of PTMT with epoxy coated aluminium rod & high desity plastic ball ascrewed for iron pipe of 20mm bore and fixed complete all as specified and as directed.

S&F in repairs Gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe 20 mm bore, complete all as specified and as directed.

S&F PVC connections 450mm long with brass unions at both ends suitable for 15mm bore pipe, complete all as specified and as directed.

S&F in repair 15 mm Angle valve/Stop valves, cast copper alloy, chromium palted, fancy type screwed down high pressure with crutch and butter fly handles, screwed with iron pipes or for union complete all as specified and as directed.

S&F in repair 15 mm Angle valve/Stop valves, (concealed type) cast copper alloy, chromium palted, fancy type screwed down high pressure with crutch and butter fly handles, screwed with iron pipes or for union complete all as specified and as directed.

S&F in repairs bib tap, brass chromium plated fancy type, long body with flange screwed down, screwed for iron pipe 15 mm bore complete all as specified and as directed.

S&F in repairs, brass spindles with knobs suitable for concealed stop valves/ bib tap/ pillar tap/ hot and cold mixture etc. complete all as specified and as directed.

S&F in repairs, sink mixer for mixing valve 15mm dia wall mounted with 165mm long swivel spout, connecting legs and wall flanges, Hot and Cold CP brass fancy including joints to steel pipe or unions, including fittings complete all as specified and as directed.

S&F in repairs, Central hole mixer for mixing with 450mm braided connection pipe 15mm dia, Hot and Cold CP brass fancy including joints to steel pipe or unions for centre hole wash hand basin, including fittings complete all as specified and as directed.

S&F in repairs, wall mixer with bend pipe for overhead shower mixing valve Hot and Cold water Screwed Down for iron pipe 15mm dia CP brass fancy including joints to steel pipe or unions, including fittings for complete all as specified and as directed.

S&F in repairs two way Chromimum plated bib cock 15mm dia with single handle and wall flange complete all as specified and as directed.

S&F in repairs, CP brass health faucet alongwith 1.00 to 1.50 meter good quality SS flexible connection pipe suitable for 15mm bore pipe complete all as specified and as directed.

S&F in repairs, Brass chromium plated shower rose 120mm size with arm complete all as specified and as directed.

S&F in repair stainless steel towel rack fixed with sutable screw complete all as specified and as directed.

S&F in repairs chromium plated grating with 100mm dia with/without hole of approved make includingh fixing with 1:4 cement mortar to floor/ nahni trap etc. complete all as specified and as directed.

S&F in repair brass chromium plated tubular towel rail, 20mm dia, 'D' type 60cm long between flanges of brass CP complete all as specified and as directed.

S&F in repair stainless steel sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, plan size 1050 mm x 500 mm complete all as specified and as directed.

S&F stainless steel Soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and as directed.

S&F corner glass assmbley with stainless steel railing, fixed to plugs with chromium plated brass screws complete all as specified and as directed.

S&F in repair vitreous china wash down water closet pan with P or S trap (pedestal pattern) , white fixed in repair,including sheet cover of closed pattern with flat bottom and mild steel chromium plated or aluminiumised hinging device, complete all as specified and as directed.

S&F in repair, PVC valveless, syphonic action type flushing cisterns 10 ltrs capacity , low level, white, with inlet ball valves, float and handle including brackets and pvc flush pipe 32 mm dia for low level complete all as specified and as directed.

S&F in repair brass chromium plated bottle traps for wash basins with inlet and outle screwed for pipe or connections including necessary packing, union and cap and fixed 40mm-270 gms) complete all as specified and as directed.

S&F in repair Vitrous china wash hand basin white, ovel type over counter sunk Wash hand basin size 550x 400mm, including necessary waste pipe and coupling, fixing in Granite counter sunk complete all as specified and as directed.

S&F in repairs, PVC waste pipe 32mm bore, 65cm long plain including suitable adopter complete all as specified and as directed.

S&F Toilet paper holder with flat recessed type stainless steel complete all as specified and as directed.

S&F SS towel Ring fixed with and including Chromium plated brass screws complete all as specified and as directed.

S&F MS chromium plated peg set of five fixing with wall complete all as specified and as directed.

Demolition of brick work built in cement mortar or cement lime mortar including quions and arches complete all as specified and as directed.

M&L for brick work with sub class `B' bricks straight or curved on plan exc. 6mtr mean radius built in cement mortor 1:6 complete all as specified and as directed.

All as per item No 68.00 here-in-before but except bricks.

M&L for Brick work with sub class 'B' bricks strainght or curved on plan to any radius in half brick thick in cement mortar 1:4 complete all as specified and as directed.

Taking down chowkats with shutters exceeding 1.5 Sqm each and not exc. 4.00 sqm each (without taking off shutters from the frames) complete all as specified and as directed.

Taking down shutter of any descreption exc. 1.00 sqm but not exc. 2.00 sqm each complete all as specified and as directed.

S&F pressed steel frames double rebated of size 125mm x 60mm for doors including necessary fixing lugs, hinges, lock strike plate etc complete all as specified and as directed.

S&F pressed steel frames single rebated of size 105mm x 60mm for doors including necessary fixing lugs, hinges, lock strike plate etc complete all as specified and as directed.

M&L for cement concrete 1:3:6, type C-1, using 20 mm graded stone aggregate as in fillings and mass concrete, filling backs of chowkats etc complete all as specified and as directed.

M&L for cement concrete (1:2:4) type B-1 using 20 mm graded stone aggregate as in lintels upto 1.50 m clear span, cills , steps, seismic and other similar bands, copings, kneelars, apex stones, bed plates, bed blocks of hold fasts etc including necessary form work complete all as specified and as directed.

S&F 35 mm thick flush shutters (any number of panels), solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed.

S&F aluminium anodised barrel tower bolts, 150 mm long of extruded section and fixed complete all as specified and as directed.

S&F aluminium handles, 150 mm size, fabricated type complete all as specified and as directed.

S&F aluminium alloy anodised sliding door bolts of 250 mm long with hasp, staple (bolt type) fixing clips of sheet cast or extruded section, fixing bolts and sliding bolts of extruded section and fixed complete all as specified and as directed.

M&L for preparation of new wooden surfaces of any description not otherwise described over 10 cms width or girth and apply one coat of synthetic enamel paint complete all as specified and as directed.

M&L for preparation of old wooden surfaces of any description not otherwise described over 10 cms width or girth and apply one coat of synthetic enamel paint complete all as specified and as directed.

M&L for Stainless steel (SS) 316 grade any section like tee, angle, hollow pipe and square/rectangular tube, flat plates etc as fixed with necessary fittings SS screws, nut, bolts, fastners, washers etc (as approved by Engr-in-charge) including necessary cutting drilling profile, cutting of components to required length/width and shapes/profile and smooth grinding/maching of edges/ faces/all welding joints including buffing and polishing complete all as specified and as directed.

S&F for mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/ or riveted, welded or forged into spikes, framed guard bars, window frames, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work fixed in position including holdfasts or screws confirming to Fe.290.Gde-E-165 complete all as specified and as directed.

M&L for preparation of new steel surfaces of any description not otherwise described over 10 cms width or girth and apply two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

M&L for preparation of old steel surfaces of any description not otherwise described over 10 cms width or girth and apply one coat of synthetic enamel paint complete all as specified and as directed.

Dismantling boarding, any description, fixed in any position with nails, complete all as specified and as directed.

M&L for 18mm thick wood plastic composites (WPC) board,in patches fixed with screws as in cupboard/ wardrobe/ almirah shutter/kitchen cabinet boxes, including PVC beading all around and all necessary fittings and fixtures like nickle plated clip hinges, knobs etc complete all as specified and as directed. Note: (a) Pattern & design of WPC board to be decided by GE. (b) Items like, magnetic Catcher, cupboard 100mm SS handle, and continuous (piano) hinges,mild steel, bright finish or electrogalvanised , width of flap (when open) is 30mm deemed to be included in the quoted rate.

S&F in repair magnetic catcher for cupboard shutter (02 for each cabinet) best quality with screw complete all as specified and as directed.

S&F in Repair U shaped 600 mm long double stainless steel channel of size 10mmx 20mmx 1.50mm fixed to wooden frame including suitable rail / rollers etc complete all as specified and directed .

S&F in repair 150mm long aluminium anodised hasp and staple bolt, brass with mild steel hinge pin 40/50mm dia, cup board knobs fixed with nut, screws and washers of aluminium, anodised, complete all as specified and as directed.

S&F in repair stainless steel wire cloth best quality, 0.63mm nominal dia or wire and sqm average width or aperature 1.40mm, fixed with tinned tacks or galvanised wire staples to steel doors, windows complete all as specified and as directed.

M&L for welding in repairs exc 2.5 cm but not exc. 5.0 cm in length thickness of metal be welded exc 6mm but n.exc 9mm, complete all as specified and as directed.

S&F in repairs 1.00mm thick stainless steel plate rack overall size (31X36X10 inch) fixed with steel screws complete all as directed.

S&F in repair aluminium anodised barrel tower bolts, 150 mm long of extruded section and fixed complete all as specified and as directed.

S&F in repair aluminium handles, 150 mm size, fabricated type complete all as specified and as directed.

S&F in repair aluminium alloy anodised sliding door bolts of 250 mm long with hasp, staple (bolt type) fixing clips of sheet cast or extruded section, fixing bolts and sliding bolts of extruded section and fixed complete all as specified and as directed.

Dismantling of cast iron or reinforced concrete or PVC pipes of any dia, jointed in cement mortar and taking out of trenches, if required, complete all as specified and as directed.

S&F 110 mm PVC (SWR) pipes single socketed, in any length, fixed in floors or wall complete all as specified and as directed.

S&F 75 mm PVC (SWR) pipes single socketed, in any length, fixed in floors or wall complete all as specified and as directed.

S&F 75mm PVC (SWR) bends/Tees/ Sockets type ‘B’ (any radius) complete all as specified and as directed.

S&F 110mm PVC (SWR) bends/Tees/ Sockets type ‘B’ (any radius) complete all as specified and as directed.

S&F in repair PVC (SWR) floor/ nahani trap including jointing with solvent cement, dia of outlet 75mm complete all as specified and as directed.

S&F for 75mm PVC (SWR) Branch pieces, PVC (SWR) branch piece, single (single Y) equal or unequal complete all as specified and as directed.

S&F for 110mm PVC (SWR) Branch pieces, PVC (SWR) branch piece, single (single Y) equal or unequal complete all as specified and as directed.

M&L for providing and injecting chemical chlorpyrifos emulsifiable for post constructional anti termite treatment to wooden or wall below concrete or masonary apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes complete all as specified and as directed.

Disconnecting existing tanks of 250Ltrs capacity, setting aside (or lowering if required) and and re-fixing in same position after cleaning the tank complete all as specified and as directed. (Rate for cleaning to be quoted under this item only).

Disconnecting existing tanks of 300Ltrs capacity, setting aside (or lowering if required) and and re-fixing in same position after cleaning the tankcomplete all as specified and as directed. (Rate for cleaning to be quoted under this item only).

Disconnecting existing tanks of 1000Ltrs capacity, setting aside (or lowering if required) and and re-fixing in same position after cleaning the tankcomplete all as specified and as directed. (Rate for cleaning to be quoted under this item only).

Cleaning of settled down mud/de-silting/dirty including De-watering in side the Tank of capacity 40,000 Ltrs of Block No 1 to 16 at Tarapore Officers Enclave at Rangpuri Area under Garrison Engineer (South) Delhi Cantt-10. (a) M&L including necessary T&P for De-watering through electric driven pump of capacity set 3 HP (1/3 phase) required at site for lifting of staining water from in side the Tank of Capacity 40,000 Ltrs (in three portion of Officer/Servent/Fire fight tank)-01 Job (b) For taking out and removal of settled down mud/sludge inside the Tank of Capacity 40,000 Ltrs (on the top of Blocks) for scooping out from inside and below hte staining water in Sump and lifting the mud and deposited on top of the Block and further to removal the same and deposited where directed by the Engr-in-Charge-01 Job (c) Labour for cleaning the tank properl after removal the settle down mud/sludge claning with water and drain out the dirty water from the tank and refiling the properly for reusing the tank :-01 Job

Material and labour for water proofing treatment of sunken floor of WCs, bathroom etc. by applying of the following specifications :- (i) Cleaning of sunken floor surface with mechanical means i.e. wire brush/air blower etc. and remove all loose/unsound material, dirt, dust, etc. (ii) Applying cement slurry mixed with acrylic based polymer modified cementitious composite compound coating Hydroproof Xtra of FOSROC/Equivalent of Dr Fixit of Pidilite Industries Ltd in the ratio of 1:2:4 (One part of acrylic polymer : Two part of water and four part of cement). (iii) First layer of cement slurry @ 0.444 Kg/Sqm mixed with acrylic based modified cementious composite compound @ 0.222 Litre/Sqm and allow it to air dry for 04 hours. (iv) Second layer of cement slurry @ 0.222 Kg/Sqm mixed with acrylic based polymer modified cementitious composite compound @ 0.111 Litre/Sqm and allow it to air dry for 04 hours followed with water curing for 48 hours. (v) 200 micron thick polythene film shall be pasted with help of adhesives over treatment. Note :- Joints of WC/Trap/Soil waste shall be properly sealed with sealing compound. Testing of all traps and joint and sunken slab shall be done as per IS-1742 before filling and tiling work.

Material and labour for plain cement concrete 1:5:10 type E-2 (using 40mm graded broken bricks aggregate) as in foundation, filling and mass concrete, complete all as specified and as directed.

Material and labour for 25mm thick plain cement concrete 1:2:4 type B-0 (using 12.5mm graded stone aggregate) as in levelling courses laid and compacted in slope in floor complete all as specified and as directed.

S&F in repair PVC syphone kit dual button push type flushing cistern of 10 Ltr capacity, including push buttons complete all as specified and as directed.

Note :- (i) The contract sum shall be after deducting the amount of Credit shown in Sch of Credit of this Tender. (ii) If any item of same description in nature is found to be entered as "double in BOQ" and the bidder quotes different rates against same item, then the rate quoted on lower side shall be applicable and higher rate will not be allowed to be paid in any circumstances. No claim on this account shall be entertained on a later date.

Ex Serviceman Enterprises (BID ID -3282833)

YP INFRA (BID ID -3278822)

vineet pal (BID ID -3282737)

M/S MANISH KUAMR SINGH (BID ID -3282862)