Improvement works Rooms, Kitchen, Restaurant and New Reception Building at Hotel Tamilnadu Tharangambadi Mayiladuthurai District

Amount

Dismantling, Clearing away and carefully stacking materials useful for re-use for any thickness of walls for Floor finish and dadooing walls in cement mortar with mosaic tiles / glazed tiles / cuddapah slabs etc., Complete complying with standard specification.

Dismantling, Clearing away and carefully stacking materials useful for re-use for any thickness of walls for Brick / stone masonry in lime mortar walls under 3m high etc., Complete complying with standard specification.

Dismantling, Clearing away and carefully stacking materials useful for re-use for any thickness of walls for Doors & windows including removal of frames, hinges and fastenings etc., Complete complying with standard specification.

Dismantling, Clearing away and carefully stacking materials useful for re-use for any thickness of walls for Pressed tiles & weathering course etc., Complete complying with standard specification.

Dismantling, Clearing away and carefully stacking materials useful for re-use for any thickness of walls for Dismantling RCC etc., Complete complying with standard specification.

Dismantling, Clearing away and carefully stacking materials useful for re-use for any thickness of walls for Dismantling PCC etc., Complete complying with standard specification.

Dismantling, Clearing away and carefully stacking materials useful for re-use for any thickness of walls for chipping of concrete and roughing the surface etc., Complete complying with standard specification.

Installation of Vertical Bored cast in situ RCC piles of following diameter in all types of soils, using Standardised Concrete Mix of following grade, with sulphate resistant Cement or OPC/PPC, etc and Crushed Stone Sand and 20mm and down graded HBGS jelly coarse aggregate. The rate includes cost for placing of reinforcement cage in bore hole in correct position, cost of boring to the required depth with Bentonite solution with temprory casing of required length, conveyance of RMC to site and pouring concrete using Tremine pipes, conveyance of all materials to the site including all tools and plants, shifting the plants and equipments from one point to another, excavtion of mud pits for circulation of Bentonite soultion, closing the mud pits to original level and mud removal with initial lead and lift but including dismantling the concrete above the cut off level etc complete as directed by the departmental officers including socketing. The reinforcement cage should be welded properly for lifting. The concrete cubes to be tested as per IS 456-2000. Acceptance criteria by clause 16.1. Frequency of testing as per 15.2.2. Testing to be conducted at both the ends at site as well as RMC plant. Pile driving depth should be decided by the departmental officers at site. The length of pile for payment shall be measured from top of shoe to the bottom of the pile cap.( Cost of Reinforcement provided for Pile and Welding charges shall be measured and Paid separately )

Earth work excavation for foundation in all soils and sub soils except rock requiring blasting to full depth as may be directed inclusive of shoring, strutting and baling water wherever necessary including refilling the sides of foundation with excavated earth in layers of not more than 20cm thick well rammed, watered and consolidated and depositing the surplus earth within the compound in places shown by the Departmental Officers with an initial lead of 10 metres and lift of 2 metres and clearing and levelling the site etc. complete complying with standard specification.

Earth work open excavation for foundation in all soils and sub soils except rock requiring blasting to full depth as may be directed inclusive of shoring, strutting and baling water wherever necessary including refilling the sides of foundation with excavated earth in layers of not more than 20cm thick well rammed, watered and consolidated and depositing the surplus earth within the compound in places shown by the Departmental Officers with an initial lead of 10 metres and lift of 2 metres and clearing and levelling the site etc. complete complying with standard specification.

Cement concrete of mix 1:5:10 (One cement, five sand and ten aggregate) using 40mm size ISS gauge hard broken granite stone for foundation including all incidental charges dewatering if found necessary and laid in layers of not more than 15cm thick, finishing and curing as directed by the Departmental Officers complete complying with standard specification.

Filling in foundation and basement excavated earth in layers of 15 cm thick well rammed and consolidated including watering etc., complete complying with standard specification.

Supplying and filling of gravel including conveyance unloading rehandling filling along the alignment watering and consolidation with hand roller etc. complete complying with standard specification.

Supplying and filling the foundation and basement with filling M. sand in layers of not more than 15cm thick well rammed, watered and consolidated as directed by the Departmental Officers complete complying with standard specification.

Supplying and erecting steel centering including supports for plane surfaces in foundation and basement and in all floors for reinforced cement concrete works such as columns footing, plinth beam, grade beam, staircase steps, bad block etc. which require only nominal strutting using M.S.sheets of size 90cmx60cm B.G.10 stiffened with mild steel angles of size 25x25x3mm for boarding laid over silver oak joists of size 10x 6.5cm spaced at about 90cm centre to centre and supported by casurina props of 10cm to 13cm dia spaced at 75cm centre to centre at suitable intervals etc. complete complying with standard specification.

Supplying and erecting steel centering for sides and soffits including supports and strutting upto 3.29m height for plane surfaces as detailed below in all floors with all cross bracings using mild steel sheet of size 90cm x 60cm B.G.10 stiffened with welded M.S.angle of size 25x25x3mm for boarding laid over silver oak (country wood) joists of size 10cmx6.5cm spaced at about 90cm centre to centre and supported by casurina props of 10cm to 13cm dia spaced at 75cm centre to centre at suitable intervals etc. complete in all floors complying with standard specification

Plane surfaces such as RCC floor slab, roof slab, rectangular square Tee or Ell beam, lintels, staircase waist slab, landing slab, landing beams, portico beams, portico slab etc.

Plane surface such as RCC. Square for rectangular columns top and bottom slab of sunshade boxing sill slab to window etc.

For circular portico column

Providing and laying in position, Standardised Concrete Mix M-35 Grade by insitu machine mix concrete adopting weighing batch method in accordance with IS:456-2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 425 kg/m3 and maximum water cement ratio of 0.45, including admixture (plasticiser / superplasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 Cu.m) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 Cu.m) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m’) 7670 kg. of crushed stone sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No separate payment will be made by the Department for the excess usage of materials).

Foundation and basement

In Ground Floor

First Floor

Second floor

Third floor

Plain Cement concrete of mix 1:2:4(One cement, two sand and four aggregate) using 20mm size ISS gauge hard broken granite stone for wearing coat in foundation and basement including laying, finishing and curing as directed by the Department Officers complete complying with standard specification. For Foundation & Basement

Cement concrete of mix 1:3:6 (One cement, three sand and six aggregate) using 40mm size ISS gauge hard broken granite stone for dummy columns with nominal reinforcement including, laying, consolidating, finishing and curing as directed by the Departmental Officers complete complying with standard specification. In First Floor

Supplying, fabricating and placing in position of mild steel or ribbed tor steel grill for all reinforced cement concrete works including cost of steel and G.I. binding wire as directed by the Departmental Officers comlpete complying with standard specification.

Brick work in following Cement Mortar using best quality of country bricks of size 8-3/4" x 4-1/4" x 2-3/4" for foundation and basement including curing, etc., complete complying with standard specifiction. Cement Mortar 1:5 a)Foundation and Basement

Brick work in following Cement Mortar 1:6 using best quality Fly ash Brick of size 230x110x70mm with class designation of 7.5 conforming to IS 13757-1993 or IS 12894-2002 for foundation and basement including Cost of Mortar Plasticizer, curing,etc., complete complying with standard specification and as directed by the departmental officers. Brickwork shall be done as per IS 2212-1991 adopting English Bond generally. other type of bond shall be done as directed by the Executive Engineer in charge.

Foundation and Basement

In Ground floor

In First floor

In Second floor

In Third floor

Brick partition walls of 11.50cm thickness using best quality Fly ash Brick of size 230x110x70mm with class designation of 7.5 conforming to IS 13757-1993 or IS 12894-2002 in Cement Mortar 1:3 (One Cement and Three CS Sand) using hoop iron reinforcement if found necessary including Cost of Mortar Plasticizer, curing etc. complete complying with standard specification and as directed by the departmental officers.

Ground Floor

First Floor

Second Floor

Damp proof course in Cement mortar 1:4 (One cement and four sand) 12mm thick including water proofing compound 2% by weight of cement used as directed by the Departmental Officers etc.complete complying with standard specification.

Special ceiling plastering and finishing all reinforced cement concrete exposed surface such as reinforced cement concrete slab, sunshades, staircase steps landing slab with cement mortar 1:3 (One cement and three sand) 10mm thick including hacking the surface and providing necessary cement mortar nosing beadings wherever necessary using the same mortar as directed by the Departmental Officers complete complying with standard specification.

Plastering with cement mortar 1:5 (One cement and five sand) 12mm thick in all floors including finishing and curing as directed by the Departmental Officers complete complying with standard specification.

Plastering with cement mortar 1:3 (one cement and three sand) 12mm thick with WPC 2% by weight of Cementin all floors including finishing and curing as directed by the Departmental Officers complete complying with standard specification.

Supplying and fixing of M.S.Grills for windows,Ventilators of and (or) directed by the Engineer incharge including cost of M.S.charges and cost of one coat of red oxide primer with labour coat etc., complete complying with standard specification.

Paving the floor with Designed coloured glazed Ceramic tiles of approved quality and all colours of size 305x305x6mm for flooring in all floors over a base layer of cement mortar 1:3 (One cement and three sand) 20mm thick and pointing with white cement using 0.30 Kg.of white cement per square metre including adding suitable colour pigments to suit the colour of tiles finishing perfectly and curing as directed by the Departmental Officers including cost of tiles, all materials and incidental charges, transportation charges and labour charges for laying tiles as directed by the Departmental Officers complete complying with standard specification.The tiles should be got approved by the Departmental Officers before use on work.

Paving the floor with pre-polished concrete Cement based Hydraulically pressed Anti skid tiles 305mmx305mm (pattern design) - 20 mm thick (Required shape and design) of 20mm thick of approved quality and colour laid in Cement Mortar 1:3 (One Cement and Three sand) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Paving the floor with best approved quality fine polished Granite Stone Slabs ofof size 1200 X 600mm and above (8 X20mm thick) in all floors in CM 1:3, 20mm thick Granite slab (Ruby Red/Raw Silk/Jet Black) and Variety with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three crushed stone sand) with required Cement Slurry and Mortar Plasticizer and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc., complete complying with standard speicification and as directed by the departmental officers.(The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work)

Paving the floor with pre-polished concrete anti-skid step tiles (Required shape and design) of 20mm thick of approved quality and colour laid in Cement Mortar 1:3 (One Cement and Three crushed stone sand) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Labour charge for finishing the top of working table and staircase step portion with nosing arrangements in Granite Slab/tiles including cutting the edges and polishing including cost of polishing materials

Finishing the floor with Vitrified tiles of approved quality and colour of size 600x 600 x 10mm for flooring in all floors over a base layer of cement mortar 1:3 - 20mm thick and pointing with white cement using 0.30kg of white cement per square metre including adding suitable colour pigments to suit the colour of tiles are finishing perfectly and curing as directed by the Departmental Officers including cost of tiles, all materials and incidental charges, transportation charges and labour charges for laying tiles as directed by the Departmental Officers complete complying with standard specification.The tiles should be got approved by the Departmental Officers before use on work.

Providing and laying 83 mm thick HIGH strength type of interlocking paver blocks of approved colour made up to designed concrete mix 1:1:2 using 10 to 12 mm size HBG stone jelly in required shape and size having minimum compressive strength of 40 N/mm2 to be laid flurrying bone pattern with approved nonsticking surface at Top.The rate is inclusive of levelling the site, providing M. sand cushion 100 mm thick,compacting with power compacter and sweeping the sand grouting and also inclusive of transportation charges, loading & unloading and labour charges for laying the paver block etc, complete and as directed by the departmental officers .

Dadooing the walls with Colour Glazed Tiles of size 300x450x8mm of approved quality laid in cement mortar 1:2 (One cement and two sand) 10mm thick and pointing with white cement using 0.40Kg.of white cement per square metre including cost of tiles, all materials, incidental charges, transportation charges and labour charges for fixing tiles neat finishing the joint flush curing as directed by the Departmental Officers complete complying with standard specification. The tiles should be got appproved by the Departmental Officers before use on work.

Supplying and fixing Cuddappah slab for cup-board 18/20mm thick etc., complete complying with standard specification and as directed with the departmental officers.(The Cuddappah slab should be got approved from the Executive Engineer before use on work.

Supplying and fixing Teakwood frame with scantling above 2m for doors including labour charges for wrought and putup and fixing holdfast in frame etc., complete complying with standard specification and as directed by the departmental officers

Renewing and fixing the Single Leaf 1/3rd panelled and 2/3rd louvered door shutter Two wings openable type by using well seasoned teakwood of superior quality and approved variety as per the original design and pattern instructed by the Engineer In Charge.The door shutters is made with 1/3rd panelled shutters at bottom and 2/3rd louvered panels at top. The door shutter is made with two number of 75mm x 40mm size vertical styles, top rail, lock rails and bottom rail of size 100mm x 35mm , 200mm x 35mm, 120mm x 35mm respectively. The bottom 1/3rd portion of door shutter panels is covered with teakwood planks of 35mm thick and top 2/3rd portion of the shutter panels is covered with teakwood louvered planks of size 170mm x 20mm of 12 Nos.for each leaves and one number of teakwood scantling of size 35mm x 30mm in ornamental of existing style is provided of full height of louvered shutter for operating the louvered shutter including all necessary fittings brass/ steel hardwares like screws, nails, hinges, hooks, tower bolts, handles, aldrops of same design, size and weight,etc., complete. Item to also include making all the mouldings and design of the panels as in the existing evidence. Item to include complete finishing of the shutters as directed by the departmental officers. (The rate inclusive of cost of all teakwood materials, labour wrought and putup of door frames and shutters , cost of all furniture fittings, labour charges for fixing in position etc., complete complying with standard specifications (four leaves).

Renewing and fixing Double leaf the 1/3rd panelled and 2/3rd louvered door shutter Two wings openable type by using well seasoned teakwood of superior quality and approved variety as per the original design and pattern instructed by the Engineer In Charge.The door shutters is made with 1/3rd panelled shutters at bottom and 2/3rd louvered panels at top. The door shutter is made with two number of 75mm x 40mm size vertical styles, top rail, lock rails and bottom rail of size 100mm x 35mm , 200mm x 35mm, 120mm x 35mm respectively. The bottom 1/3rd portion of door shutter panels is covered with teakwood planks of 35mm thick and top 2/3rd portion of the shutter panels is covered with teakwood louvered planks of size 170mm x 20mm of 12 Nos.for each leaves and one number of teakwood scantling of size 35mm x 30mm in ornamental of existing style is provided of full height of louvered shutter for operating the louvered shutter including all necessary fittings brass/ steel hardwares like screws, nails, hinges, hooks, tower bolts, handles, aldrops of same design, size and weight,etc., complete. Item to also include making all the mouldings and design of the panels as in the existing evidence. Item to include complete finishing of the shutters as directed by the departmental officers. (The rate inclusive of cost of all teakwood materials, labour wrought and putup of door frames and shutters , cost of all furniture fittings, labour charges for fixing in position etc., complete complying with standard specifications (four leaves).

Solid PVC door shutters using 19 Gauge 19mm MS square tubes for styles and outer frames. 15mm MS square tubes for top, lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC sheets. Shutter using 5mm thick solid PVC sheets for panelling shall rigidly fixed in position including necessary furniture and fittings. The over all size of styles shall be 50mm x 30mm. The over all size of top rail, Lock rail and bottom rail shall be 75mm x 30mm. The over all size of frames shall be 50mm x 45mm, with suitable rabate for housing the shutter.

Renewing the damaged teak wood ornamental hand rail in stair case and verandha portion with superior quality of teak wood and kadasal work in all the members, the top member of size 8 x 6 cm with curved surface, in bottom member of size 10 x 8 cm, the internal vertical supports are 6.5 x 6.5 cm, the internal bracing and design members of side with 2.50 x 2.50 cm with complete kadasal works, the rate inclusive of cost teak wood, skilled labour charges, necessary screws, nails, etc., complete complying with standard specification as directed by the departmental officers.

Supplying and fixing in position European water closet with P or S trap and double flapped seat cover, PVC or Porcelain low level flushing tank including all internal fittings on CI brackets, 12mm brass nipple, chromium plated etc

Supplying and fixing in position Indian make bewelled edge mirror of approved quality and brand of size 600x450mm with necessary plastic back, PVC. Frame with bottom stand of approved colour with brass screws, rawal plugs etc. complete complying with standard specification. The materials should be got approved by the Departmental Officers complete complying with standard specification.

Supplying and fixing best approved quality Brass Chromium Plated Towel Rail 600 mm Long and 20mm Diametre with brackets of same materials including cost teakwood plug and CP Screws etc.,complete complying with standard specifications.

Supplying and fixing best approved quality CP soap tray of size 150mm X 100mm including cost of teakwood plugs, brass screws etc., complete complying with standard specifications.

Supplying and fixing in position best quality of approved make white glazed earthernware wash hand basin of size 550x400mm with a pair of cast iron brackets, including cost of 15mm diametre brass chromium plated pillar tap, 32mm diametre C.P.waste, 32mm diametre PVC.Waste pipe with rubber plug and chain, 15mm diametre gun metal wheel valve, 15mm dia brass nipple, 15mm dia nylon connection etc. including fixing the wash hand basin in the wall in position with pair of C.I.brackets with teak wood plugs and screws and giving necessary water supply connection and painting the brackets with two coats of paint over a priming coat of anti-corrosive paint including testing for leakage etc. complete as directed by the Departmental Officers complying with standard specification.

Supplying, laying and jointing PVC soil pipes of approved and best varietyconforming to IS.Specification with ISI.mark of the following sizes including, cutting and threading of PVC.Pipes, fixing specials but excluding cost of such specials but including fixing to wall with necessary teak wood plugs, PVC.clamps and screws making holes on the wall (or) drilling holes in roof and making good the dismantled portion to original condition with necessary brick work and plastering wherever necessary with necessary scaffolding charges.The PVC.Pipes should be got approved by the Departmental Officers before use on work.Above ground level.

110mm dia PVC pipe

75 mm dia PVC pipe

Supplying & Fixing in position best quality PVC soil/waste pipes of various sizes of approved brand and quality confirming to I.S.S and providing leakproof joints with spun yarn and making connection to all sanitary fittings dismandling masonry or R.C.C work wherever necessary and making good the dismandled portion to the original condition including painting the castiron pipe and fittings with two coats of anti - corrosive paint of approved quality and colour and the pipe fixed in position in true alignment,complying with standard specifications etc., (The PVC pipe should be should be got approved by the Executive before use on works.) Below ground level a) 160mm dia PVC pipe

Supplying and fixing in position 15mm dia Chromium Plated brass screw down tap (heavy type and long body) of approved make conforming to ISS.and including cost of shellac, thread complete complying with standard specification and including cutting and threading wherever necessary.(Taps should be got approved by the Departmental Officers before use on the work)

Construction of Inspection chamber in Brick work using 9" x 4 3/8" x 2 3/4" size Chamber bricks with a clear size of 0.60 x .0.60 x 0.78m to a thickness of 0.23m in cm 1:5 over the CC 1:5:10 using 40mm kg HBSJ walls to a thickness of 0.23m and 1.12mx1.12m size and sand filling to a size of 1.12mx1.12m to a depth of 0.12m with necessary earthwork excavation of size 1.12mx1.12mx1.20m(Depth) including plastering the wall to a height of 0.78m inside the chamber and 0.55m on outer wall and top surface of the chamber and forming channel in the bottom of chamber and forming channel in the bottom of chamber and forming in CC 1:3:6 using brick jelly of 20mm size also including necessary RCC cover slab with necessary steel Reinforcement etc.,complete.

Teakwood wrought & putup for joist, beam, rafters and purlins,etc., which are in full length new member placed for supporting the Madras Terrace roof/ Mangalore tiles roof or any other area in all floor as directed by the departmental officers by using well seasoned superior quality and approved variety of teakwood for heritage building work including fixing of iron holdfasts incase of doors, windows and ventilators etc.,and excluding cost of holdfasts and making necessary size holes in the masonry to receive the ends of wooden joists, beams, etc., all fixtures and fastenings etc., complete. Item to include all moulding and chamber to be made as per original design indicated by the Engineer In Charge. (The rate includes the cost of teakwood, labour charges for wrought and putup to the existing clue/design, fixing in position to true alignment and gradient wherever necessary. Complying with standard specifications and as directed by the departmental officers (sample of teakwood to be shown to the Executive Engineer concerned for approval before use on work). Application of Solignum on the wooden surface should also be done. In all floors

Finishing the top of roof surface using specially manufactured superior quality terrace tiles of size 150x150x25mm (nattu odu) for heritage works laid with Lime mortar 1:2 (one Lime and two sand). The Terrace tiles should be laid on such a manner with proper slope and gradient that the rain water gets discharged easily through rain water outlet pipes freely. The quality of lime to be procured from Pollachi shall be of best and high calcium oxide content quality etc complete.The rate including cost of all materials,Labour charges, lift arrangements, tranportation of material from G.F to T.F by head load and finishing neatly etc complete.

Supplying and fixing in position PVC nahini trap of various sizes with S.S gratings of approved brand and quality fixing over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two parts of sand and five parts of 40mm brick jelly) and finished with cement mortar 1:3 (One cement and three sand) including dismantling, masonry works wherever found necessary and making good the damaged portions to the original condition and giving connections to the PVC. Pipes as directed by the Departmental Officers complete complying with standard specification. (The PVC. Nahini Trap should be got approved by the Departmental Officers before use on work) P.V.C.Nahini Trap of size 100x75mm

Providing pre-construction Anti termite treatment by using ISI specification 6313(part-II)1981 with ten years quarantee. If any fault infestation is found during quarantee period it will be treated at free of cost.The work will be carried out as directed by the departmental officers

Renewing and fixing of louvered shutters for windows of size 1.25x1.83m openable type by using well seasoned teakwood of superior quality and approved variety as per the original design and pattern instructed by the Engineer In Charge The window shutter is made of vertical styles of size 80mm x 30mm toprail, middle rail and bottom rail of size 80mm x 30mm , 150mm x 30mm, 80mm x 30mm respectively. The panels of window shutters is covered with teakwood planks as louvered type of size 150mm x 12mm of 7 nos. placed between top and lock rail and 7 nos. of louvered panels between lock and bottom rails. Therefore total number of louvered panels is 14 nos. in a single shutter and one number of teakwood scantling of size 35mm x 30mm in ornamental of existing style is provided of full height of louvered shutter for operating the louvered shutter including all necessary fittings brass/ steel hardwares like screws, nails, hinges, hooks, tower bolts, handles, aldrops of same design, size and weight, etc., complete. Necessary groove arrangements are made in the vertical style for fixing the louvered planks. Item to also include making all the mouldings and design of the panels as in the existing evidence. Item to include complete finishing of the shutters as directed by the departmental officers.The rate inclusive of cost of all teakwood materials, labour wrought and putup of window shutters, cost of all furniture fittings, labour charges for fixing the shutters in position etc., complete complying with standard specification.

Renewing and fixing of glazed ventilator with new Teak wood glazed ventilator of size 1.20m x 0.60m by using Teak wood scanting thickness of size 0.04m frames fixed with 4mm thick pin headed glass including labour for wrought put up and fixing the ventilator in position with necessary furniture fittings including with neat finishing etc., complete complying with standard specifications and as directed by the departmental officers.

White washing two coats with freshly burnt white shell lime in all floors including cost of lime, blue powder fevicol type gum, brushes, scaffolding charges, etc., complete complying with standard specification and as directed.

Supplying and painting the walls with two coats of oil bound distemper over one coat of water based cement primer including cost for distemper, primer, cleaning and scrapping the walls, rendering the walls smooth with necessary putty, brushes, scaffolding arrangements, labour charges, etc., as per standard specification. (The colour and shade of the distemper shall be got approved by the Executive Engineer before use of work).

Supply and finishing of Texture paint over newly Primer painted wall surface with Interior grade Stucco Finish of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.

Revarnishing with wood work with two coats of best melamine varnish of approved quality and brand including preparation of surface etc.. The rate is inclusive the cost of all material, labour charges and finishing neatly etc., complete compluing with standard specification and as directed by the departmental officers

Painting the New iron works two coats with syntactic enamel paint of approved quality and colour etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Supplying and painting the walls with two coats of oil bound distemper over one coat of water based cement primer including cost for distemper, primer, cleaning and scrapping the walls, rendering the walls smooth with necessary putty, brushes, scaffolding arrangements, labour charges, etc., as per standard specification. (The colour and shade of the distemper shall be got approved by the Executive Engineer before use of work).

Revarnishing with wood work with two coats of best melamine varnish of approved quality and brand including preparation of surface etc.. The rate is inclusive the cost of all material, labour charges and finishing neatly etc., complete compluing with standard specification and as directed by the departmental officers

Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.

110 MM dia - Two Floor

160 MM dia - One Floor

Supply and fixing in position white European Water Closet of approved make with low level flushing tank 10 litre capacity of best quality and approved make with 100mm P or S trapwith double flapped rigid PVC seat cover with CP brass hinges etc. complete complying with standard specification and as directed by the Departmental officers (The EWC should be got approved by the Executive Engineer before use on works.

Supplying and fixing of CP Two Way Bib Cock with Health Faucet ,wall hook & one metre long flexible tube including cutting and making good the walls wherever required etc complete. complying with standard specification and as directed by the Department officers. The quality and make of health faucet should be got approved by Concern department Engineer before use on work.

Supply and fixing Wash Hand Basin of size 550 mm X 400 mm with all accessories such as cast Iron Brackets, 32 mm Dia C.P. Waste coupling, Rubber plug and Chain, 32 mm dia ' B ' Class G.I. Waste pipe, 15 mm Dia G.M Wheel valve; 15 mm Dia Nylon connection, 15 mm Dia Brass Nipples, 15 mm C.P. Pillar tap etc.,including fixing the wash hand basin in the wall in position with a pair of C.I. brackets with teak wood plugs and screws and giving necessary water supply connection and as directed by the Department officers. The quality and make of below counter Wash basin should be got approved by department Engineer before use on work. ( all Inclusive of cost of basin, Bottle Trap and Angle Cock)

Supplying and fixing Cp towel rail 600mm long and 20mm diameter with brackets of same materials including cost of teak wood plug and CP screws etc., complete complying with standard specification and as directed by the Departmental officers.

Supplying and fixing in position Indian make bevelled edge mirror of approved quality and brand PVC / Fibre Glass framed Various Sized and 5.5mm thick mirror, shelf type with hard board backing of approved colour fixed with brass screws, rawl plug, etc., complete complying with standard specification. (The mirror should be got approved by the Executive Engineer before use on woks) . Size 600X450X5.5mm Thick

Supplying and fixing heavy duty 15mm CP shower unit comprising of CP 15mm dia hot & cold mixer with CP spout, overhead shower set comprising of CP shower arm, rose etc.,complete with CP wall flanges. The rate including cost of all materials, labour charges and transportation etc. completed as directed by Engineer-in-Charge.

Supplying & fixing in position first quality & approved variety of various dia CPVC Ball Valves ( Heavy type ) with I.S.I. Mark of the following size including cost of Shellac, thread etc.,including labour for cutting & threading of Pipes etc., complete complying with standard specifications for both internal & external water supply arrangements.

Supplying and fixing the best quality approved make of Angle Cock with wall flange including cutting and making good the walls wherever required etc. complete complying with standard specification and as directed by the department officers. The quality and make of angular stop cock ahould be got approved by concern department engineer before use on work

Supplying and fixing the best quality approved make of C.P. Soap Tray/ Dish of size of 150mmx100mm with wall flange including cutting and making good the walls wherever required etc. complete complying with standard specification and as directed by the department officers. The quality and make of angular stop cock ahould be got approved by concern department engineer before use on work

Supplying & fixing in position 15 mm dia brass/ Hot & Cold Wash Basin Mixer C.P Tap (Heavy duty) of approved make conforming to I.S. Specifications & quality including cost of shellac, thread etc., complying with standard specifications & including cutting & threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the work).

Supplying & fixing in position 15 mm dia brass/ C.P pillar tap (Heavy duty) of approved make conforming to I.S. Specifications & quality including cost of shellac, thread etc., complying with standard specifications & including cutting & threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the work).

Supplying & fixing in position 15 mm dia PVC Bib Tap of approved make conforming to I.S. Specifications & quality including cost of shellac, thread etc., complying with standard specifications & including cutting & threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the work).

Automatic Electrical Water Heater with copper container, with Glass Wool / Puf Insulation with MS powder coated shell suitable for 25 Litres capacity 230V / 1000W (Lower End)

Supplying and fixing in position PVC cowls of following dia of best approved quality conforming to BIS, etc., complete complying with standard specifications. (The PVC cowl should be got approved by the Executive Engineer before use on works).

160mm Dia

110mm Dia

75mm Dia

Supplying & fixing in position 150 X 100 mm square mouth 'P' or 'S' trap stone ware Gully trap 'A' grade with cast iron gratings of size 300 X 300 mm with C.I. air tight cover with frames of size 300 X 300 mm at bottom & top respectively with necessary earth work excavation, laid over a bed of brick jelly cement concrete 1:3:6, 150 mm thick using 20 mm size broken brick jelly including necessary block work & plastering, &including dismantling masonry wherever necessary & redoing the damaged portions to the original condition & by using cement concrete 1:3:6 using 20 mm stone jelly for fixing the Gully trap & giving connections to the stone ware sewer line etc., complete, complying with standard specification. (The stone ware gully trap should be got approved by the Executive Engineer before use on works ).

Making Through holes in plain or Reinforced Cement Concrete with Diamond Core drilling system by using Bosch Power Tools of Following Diameter in Various thickness and Dia

100mm Dia 300mm Thk

150mm Dia 300mm Thk

Supplying,installing,testing and commissioning best quality approved/equivalent make of Single Bowl with drain board 1200X550X180 mm stainless steel double sink with brass Chromium Plateds wivalty peex tended swing sink cock 32mm dia CP waste coupling, 32mm dia heavy duty waste hose with extension pipe, 15mm CP angle valve with CP inlet connection tube,CP wall flange, including necessary bracket set ccomplete complying with standard specification and as directed by the Department officers.The quality and make o fsink and brass CP coated swiv al type sink cock should be got approved by Concern department Engineer before use on work.

Constructing brick masonry manhole with second sort Solid Blocks in CM 1:5 (one of cement, Msand) including earthwork excavation and sand filling for a depth of 150mm top cover slab with CC 1:2:4 (one of cement, two of sand, four of graded aggregate) 20mm nominal size for fixing C.I Frame, including shuttering, reinforcement foundation concrete 1:4:8 (one of cement, four of sand, eight of graded aggregate 40mm nominal size) 100mm tk., plastering inner, outer and other exposed surface with 15mm tk., cement mortar 1:3 (one of cement, three of sand) and finishing with a floating coat of neat cement with water proofing compound as per specification, making channelsin CC 1:2:4 (one of cement, two of sand, four of graded aggregate) neatly finished including fixing C.I. Cover and frame, C.I. Rungs etc., complete complying to standard specification.

Supply and fixing RCC precast slab manhole cover SFRC of 50mm thick and required size 900mm x 900mm made in CM 1:3 Ratio both direction including cost and conveyance of all materials, labour and transportation etc complete complying with standard specification.

Supplying and fixing in position the best quality and variety sizes PVC soil and waste pipes 6Kg /10Kg / cm2 of ISI mark, providing leak proof joints etc and making connection to all sanitary fittings, including dismantling masonry / RCC works wherever necessary and making good the portions. The quality and make of PVC pipes and specials should be got approved by Concern department Engineer before use on work.

160mm Dia Pipe

140mm Dia Pipe

110mm Dia Pipe

75mm Dia Pipe

40mm Dia Pipe

Supplying, laying and jointing CPVC pipes of approved quality and best variety conforming to ISS and with ISI mark of the following size including cutting, threading and fixing PVC specials but excluding cost of such specials and fixing to wall with necessary teak wood plugs, PVC clamps and screws, making good the portions to original condition with necessary brick work and concrete plastering wherever necessary with necessary scaffolding charges etc. complete complying with standard specification and as directed by the Department officers. The quality and make of UPVC pipes and specials should be got approved by Concern department Engineer before use on work.

20 mm dia CPVC pipe

40 mm dia CPVC pipe

Supplying, laying and jointing 20mm dia CPVC pipes SDR 11(having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing CPVC specials using CPVC adhesives and fixing into wall with teak wood plugs, CPVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The CPVC pipes shall be got approved by Executive Engineer before use on works. (Internal)

Supplying and fixing in position first quality and approved variety of Gun Metal /brass valve /airrelease valve /Check valve (Heavy type)with ISI mark of the following sizes including cost of Shellac,thread etc,including labour for cutting ,threading and fixing position of CPVC Pipes for both internal external water supply arrangements etc,complete complying with standard specification and as directed by the Department officers. The quality and make of valve should be got approved by Concern department Engineer before use on work

Supply & fixing a sturdy solid wood bed available in both king and queen sizes, The carefully crafted headboard has a richly textured pattern inspired by brickwork. The rich detailing complements simple lines that can work with almost any style of decor. Headboard is made of high grade Sheesham wood.Mattress board made from 12mm MDF complete as directed

Supply & fixing Bed side unit Indulge in excellence with this standout product from Gudsmith- a true testament to quality and innovation.No. of Drawers: 2,Brand Name - By Gudsmith, Particle Board Material: Engineered Wood, Material Subtype: Particle Board, Height Standard, Product Dimensions : 45.0 cm H x 40.0 cm W x 40.0 cm L complete as directed

Supply & fixing Mirror Size- 300 X 1200 (MM)Primary Material - ENGINEERED WOOD Secondary Material - Partical board, Product Dimensions : H 191cm x W 123cm x D 46cm complete as directed

Supply & fixing Type-Swing Door, Net Quantity-1 Number, No. of Shelves-8 Color-Brown, Finish-Melamine, Storage Type-Shelves, Door Type-3 Door, With Mirror-Yes, Adjustable Shelves-No,Product Dimensions : H 89cm x W 150cm x D 41cm complete as directed

Supply & fixing SWood 6 Seater Dining Set In Rustic Teak Finish, Primary Material - Sheesham Wood,Product Dimensions :Table : H 30 x W 58 x D 35;Chair : H 35 x W 17 x D 17 complete as directed

Wiring with 2 x1.5 sq.mm PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories with module GI switch box in flush with wall with 6A one way module switch with module front plate with continuous earth wire connection by 1.5 sq.mm copper wire and making good of the concealed portion with suitable colour for concealed PVC Light point/ fan point (for electronic regulator) (6 Points/ coil) Higher End

Supply and Run of 2 of 2.5 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 2.5 sq.mm copper wire and making good of the concealed portion.

Supply and run of 2 of 4 sq.mm PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with continuous earth wire connection of 4 sq.mm copper wire with painting of suitable colour.

Supply and fixing of 1 No.6/16A two module socket, 1 No. 16A one module switch on suitable module surface mounting box (Plastic) with module cover plate (Plastic) on wall with connections. Higher End

Supply and fixing of 20A Flush type Wall Socket 32A DP MCB complete set for AC Plug in flush with wall with earth connection (For AC Plug)

Supply and Laying of 3 1/2 x 120sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and clamping of 3-1/2 x 120 sq.mm PVC LTUG armoured cable on post or wall with MS clamps

Supply and fixing of brass cable gland for 3-½ x 120 sq.mm. PVC armoured LTUG cable with earth connection.

Supply and fixng of TNEB meter board suitable for 3 phase 200A service connection with copper bus bar arrangements with earth connection complete.

Main LT Panel Fabrication, Supply and erection of 160 Amps LV Main Panel floor mounted distribution cubical type panel board with lock & key arrangements having the following specifications with sheet steel enclosed, Dust & Vermin proof, floor Mounting pattern, cubical type panel made out of outer 1.6mm, inner 1.2 mm sheet steel with following switch gears and phase indication LED lamps including transportation etc., complete. Incomer: 200 Amps On load change over – 1 No Outgoing: 63 Amps MCB Switch - 4 Nos 40 Amps MCB Switch - 4 Nos BUS BAR Phase : 50 x 6mm 3 run copper flat Neutral: 25 x 6mm 1 run copper flat

Supply and fixing of 12 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 100 A 4P MCB switch as incoming and 4 nos. 32A 3P MCB, 24 nos. 6A to 32A SP MCB as outgoing on wall with earth connection only. Higher End

Supply and Run of 1 of No.8 SWG GI wire in suitable PVC rigid pipe on wall / floor / ground for earth connection

Supply and run of 25mm x 3mm tinned GI flat with necessary clamps / supports on wall / floor / ground for earth connection.

Providing chemical earthing as per the ISI specification with an earth electrode of 3.0 mtr class 'B' GI pipe with necessary funneling arrangements with necessary masonry work and with 38mm RCC over slab for the brick masonry.

Supply and Fixing of 20W LED BATTEN LIGHT Fitting

Supply and fixing of 12Watts LED Recessed ceiling Light

Supply and fixing of 15Watts LED Cove Light

Supply and fixing of 20Watts LED Hanging Light

Supply and fixing of 30Watts LED Hanging Light

Supply and fixing of 20Watts LED Parapet Light

Supply and fixing of 20Watts LED Pole Light

Supply and fixing of 20Watts LED Wall Light

Supply and fixing of 1200mm (48") sweep AC ceiling fan complete (Higher end) with 2 module 100W fan step regulator (Higher end) with 1 meter down rod with fan clamp side plates and cross arm of size 450mm (18") including giving electrical connection etc.,

Supply and fixing of 300mm (12") sweep (light duty) AC exhaust fan complete with necessary wall opening and making good of the wall.

Supply and installation of 32 A Key tag card type Legrand make or equivalent to that with its electrical connection etc., complete

Supply and fixing of AC / DC 76mm buzzer / call bell suitable for 230v 50 c/s single phase AC supply on suitable TW board with push switch to that with its electrical connection etc., complete.

Supply and run of RG-06 unarmoured Co-axial cable for TV in rigid pipe concealed in wall and ceiling and making good of the concealed portion with suitable colour.

Supply and fixing of 1 no one module TV socket with module cover plate (plastic) on suitable module concealed Box ( GI ) in flush with wall with connections.

Supply and run of 2 pair unarmoured 0.5mm telephone cable in rigid pipe concealed in wall and ceiling and making good of the concealed portion with suitable colour.

Supply and fixing of 2 nos one module RJ-45 I/O socket ans 2 nos RJ-11 I/O Socket with module cover plate (plastic) on suitable module concealed Box (GI) in flush with wall with connections.

Supply and laying of LAN cable cat -6 cable with necessary supporting clamps fixed on the roof, interconnections etc…,

Supply and Installation of 32inch Android television set incluidng wall mount etc., complete.

Supply and Installation of 3 star rated Air-Conditioner with copper coil.1.5 TR split Type AC unit with its accessories complete., etc.

Supply and Installation of 2 KVA capacity automatic voltage stabilizer for AC

Supply and Laying of 4 x 10 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and fixing of brass cable gland for 4C x 10 sq.mm. PVC LTUG aluminium armoured cable with earth connection.

Supply and Installation of 80mm dia Jindal MS B-Class pipe with fittings, incl. underground work, welding, elbow settings, valve provisions

Supply and fixing of 2×1/4 L-Angle supports with fittings & consumables

Supply and fixing of 4", 3" & 6" U-bolts with washers

Supply and fixing of 5/8 bolt & nuts

Supply and Installation of 63mm dia Type-A RRL hose 15m with SS couplings (ISI)

Supply and Installation of 2-way Fire Brigade Inlet

Supply and Installation of single-headed SS Hydrant Valve (ISI)

Supply and Fixing of single door hose box

Supply and Installation of 63mm SS branch pipe (ISI)

Supply and Installation of 80mm butterfly valve with fittings (per piece)

Supply and Installation of 25mm ball valve with fittings

Supply and Installation of 80mm NRV with fittings

Supply and Installation of 1/2" air release valve with fittings

Supply and Installation of 25mm NRV with fittings

Supply and Installation of oil-type pressure gauge with fittings

Supply and Installation of 0–14 auto switch for pump with fittings

Supply and Installation of 20mm hose reel drum with 30m double-braided nylon hose & ABS shutoff nozzle

Supply and Installation of stored-pressure ABC 6kg fire extinguisher (ISI 15683)

Supply and Installation of fire bucket set

Supply and Installation of CO₂ (4.5kg) fire extinguisher (ISI)

Supply and Installation of Jockey electrical driven pump with main pump (Kirloskar 7.5HP/5kW, 2850 RPM, 40m head)

Supply and Installation of pump house wiring with control panel

Supply and Installation of pump room flange arrangements & bolt-nut fittings

Supply and Installation of manual call point – conventional

Supply and Installation of conventional hooter

Supply and Installation of 4-zone conventional fire alarm panel (Ravel RE Type) incl. wiring labour & device fixing labour

Supply and Installation of 12V, 7Ah battery set

Supply and Installation of 1.5 sqmm × 2-core cable (approx. 90 m) incl. accessories

GST at 18%

G.Sasirani (BID ID -1548063)