KMC/DG(C)/EE(C/HQ)/ 028/2026-27, dated 19/09/2026

Labour for taking out old soling edging including removing debris (a) Single flat soling

A) Filling in foundation or plinth by silver sand in layers not exceeding 150 mm as directed and consolidating the same by thorough saturation with water, ramming complete including the cost of supply of sand. (payment to be made on measurement of finished quantity). (B) Do - by fine sand

Ordinary Cement concrete (mix 1:2:4) with graded stone chips (20 mmnominal size) excluding shuttering and reinforcement,if any, in ground flooras per relevant IS codes.

(c) Supplying and Laying in the specified pattern of Interlocking Concrete Block Pavements (ICBP) with concrete blocks (with Concrete grade as specified as per Table 1 of IS 15658: 2006) manufactured from BIS licensee manufacturer, with spacer nib (Small protruding profiles on thevertical face of a paver block used as a device for keeping minimum joint gap in between the paving blocks, as per Cl. No 3.26 of IS: 15658) and of specified size and shape with aspect ratio (The ratio of length to thickness of a paver block, as per CLNo.3.3 of IS: 15658) as per Table 2 of IS :15658 with flexural strength/breaking load as per Annexure G of IS:15658,on the prepared base course of specified CBR as per Table 1 of IRC SP 63 (2018) or else as mentioned in design and drawing with a cushion of compacted bedding sand of 25-35 mm thick (grading of the bedding sand us per clause 6.5.1 of IRC SP-63) and filling up the gaps in between paver blacks with joint filling sand (the grading of the joint filling sand will be as per clause 6.5.2 of IRC SP 63) and completing the edges with cut blocks as per Cl. No. 8.7 of IRC SP - 63(2018) with proper confinement of bedding and joint filling sand, compaction, levelling and filling up of the edge gap. 60 mm thick (a) Coloured Decorative

SUPPLYING AND LAYING FACTORY MADE VERTICAL KERB STONE OF CEMENT CONCRETE M-20 (1:1.5:3) MACHANICALY VIBRATED SIZE 500MM X 350MM X 150MM TAPERED AT TOP, MAKING JOINTS WITH CEMENT MORTAR (1:4) INCLDG COST OF ALL MATERIALS AND LABOURS BUT EXCLUDING THE COST OF UNDER BED (FOR ROAD-DIVEDER / FOOTPATH) ( REF :RATE BASED ON PWD CURRENT SOR [PWD(B) 2017, P-26 (IT -10(I)), CONSUMPTION CHART PG-B-60, SL-3 AND ANNEX-II , FORMAT-A & 3RD CORR. & ADDA. DTD-04.06.2018, P-303 , P-191 (I -6) AND 3RD CORR. & ADDA, PAGE-52, PWD-2018(R & B) P-332 (IT -18.05)), CHAPTER-1, PG-227 I-1.03, PG-230,TABLE-I , TABLE III-2 PG-226, )

Applying Exterior grade Acrylic primer of approved quality and brand on plastered or cencrete surface old or new surface to receivedecorative textured (matt finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer's specification and as per direction of the EIC. In Ground Floor (a) One Coat

Protective and Decorative Acrylic exterior emulsion paint of approved quality, as per manufacturer's specification and as per direction of Engineer-in-Charge to be applied over acrylic primer as required. The rate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer. In Ground floor (Two Coat) a) Normal Acrylic Emulsion

(a) Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc.

(A) Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary (b) On steel or other metal surface : With super gloss (hi-gloss) - (iv) Two coats (with any shade except white)

(b) Priming one coat on timber or plastered surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc.