Renovation of Panchayat Samiti Building, Mayabunder under Panchayat Samiti, Mayabunder.

Amount

Surface preparation to receive micro concrete by chipping to depth to max 75mm, cleaning removing the traces of dust, loose concrete etc. includind the cost of the labour charges, minor tools, etc complete.

Supplying preparing and priming the reinforcement steel with epoxy zinc. Primer or epoxy anti- corosive paint (Conforming to having IS/BIS Certification) including the cost of all materials labour minor tools, etc.

Supply and application of epxy concrete bonding, agent (conforming to and having BIS 6319 certification)and over cleaned and properly prepared old concrete surface to give good bonding between old and new concrete, including cost of all materials, minor tools etc. complete.

Supplying and fixing form work and shuttering to receive the micro concrete including cost of all materials all labour charges, minor tools etc.

Supplying, mixing and applying curing membrane or equivalent with water including cost of all materials all labour charges, minor tools etc. complete.

Supplying and applying high strength non shrink cementinous free flow concrete ( eith minimum 28 days flexural strength 50kg/sq.cm and compressive strength 500 kg/sq.cm as per BIS 4551-80) for above water level on site to enable completion of pouring in a continous operation. An approved grout concrete mixture of slow speed heavy duty drill and exact quantity of water as recommended should be poured into the vessel slowly and mix the same throughly in a forced action. The mix materials should be placed immediately to position foam work continously to an average thockness of 50mm without any gap including all materials and labour charges etc. complete.

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge.

Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

Dismantling cement asbestos or other hard board ceiling or partition walls including stacking of serviceable materials and disposal of unserviceable materials within 50 metres lead.

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :

Of area 3 sq. metres and below

Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within 50 metres lead of:

Asbestos Cement sheet

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources: 6 graded stone aggregate 20 mm nominal size derived from natural sources).

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, if nishing and reinforcement- All work up to plinth level :

1:1.5:3 (1 cement: 1.5 coarse sand (zone-III) derived from natural sources: 3 graded stone aggregate 20 mm nominal size derived from natural sources).

Centering and shuttering including strutting, propping etc. and removal of form for

Foundations, footings, bases of columns, etc. for mass concrete

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.

Thermo-Mechanically Treated bars of grade Fe-500D or more

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Ceosetory windows & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimensions i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

Frame size 65 x 100 mm

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately)

30 mm thick

35 mm thick

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete :

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete.

Providing and fixing plain multipurpose cement board(Hight pressure steam cured) with suitable screws for cement particle board in ceiling etc. complete (frame work to be paid seperatately).

6 mm thick Cement fiber board as per IS: 14862

Providing and laying Hollow cement concrete block walling 150mm thick consisting of hollow block of size 400x150x200mm of mix 1:3:6 (1cement:3 Pulverised sand:6 graded stone aggregates of 10mm nominal size) laid in cement martar 1:6(1cement :6 sand).

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :

Ridges plain (500 - 600mm)

12 mm cement plaster of mix :

1:4 (1 cement: 4 River sand)

Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification.

Two or more coats on new work

Distempering with 1st quality acrylic distember (Ready mix) having VOC content less than 50 grams/ litre of approved brand and manufacture to give an even shade :

Old work (one or more coats)

Finishing walls with Acrylic Smooth exterior paint of required shade :

Old work (Two or more coat applied @ 1.67 ltr/ 10 sqm) on existing cement paint surface

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :

One or more coats on old work

Painting with black anti-corrosive bitumastic paint of approved brand and manufacture to give an even shade :

One or more coats on old work

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :

Two or more coats on new work

Repair to plaster of thickness 12mm to 20 mm in patches of area 2.5 sqm and under, including cutting the patch in proper shape, raking out joints and preparing plastering the wall surface with white cement based polymer modified self curing mortar, including disposal of rubbish, all complete as per the direction of Engineer-In-Charge.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :

Kitchen sink without drain board

610x510 mm bowl depth 200 mm

Providing and fixing powder coated aluminium work (minimum thickness of powder coating 50 micron) consisting of tee/ angle sections, of approved make conforming to IS : 733 in frames of false ceiling including aluminium angle cleats with necessary C.P. brass/ stainless steel sunk screws, aluminium perimeter angles fixed to wall with stainless steel rawl plugs @ 450 mm centre to centre and fixing the frame work to G.I. level adjusting hangers 6 mm dia. with necessary cadmium plated machine screws all complete as per approved architectural drawings and direction of the Engineer-in-charge (level adjusting hangers, ceiling cleats and expansion hold fasteners to be paid for separately).

Providing and fixing 6 mm dia. G.I. level adjusting hangers (upto 1200mm length), fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40x3mm size 60 mm long and stainless steel expandable dash fastener of 12.5 mm dia and 50 mm long, complete as per direction of Engineer-in-charge.

Providing and laying four courses water proofing treatment with bitumen felt over roofs consisting of first and third courses of blown bitumen 85/25 or 90/15 conforming to IS : 702 applied hot @ 1.45 Kg per square metre of area for each course, second course of roofing felt type 3 grade-I (hessian based self finished bitumen felt) and fourth and final course of stone grit 6 mm and down size or pea sized gravel spread at 6 cubic decimeter per square metre, including preparation of surface but excluding grading complete with :

Bitumen felt (hessian base) type 3 grade I conforming to IS : 1322

Melamine polishing on wood work (one or more coat).

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work

20 mm nominal dia Pipes

Providing and fixing brass bib cock of approved quality :

15 mm nominal bore

Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete.

10 litre capacity - White

ELECTRICAL WORKS

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC Conduit, with piano type switch, suitable size PVC box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.

Group C

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC Conduit, with piano type switch, suitable size PVC box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC Conduit, alongwith 1 No 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC Conduit as required.

2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

4 X 6 sq. mm + 2 X 6 sq. mm earth wire

4 X 10 sq. mm + 2 X 6 sq. mm earth wire

Supplying and fixing Suitable PVC box on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps socket outlet and 15/16 amps piano type switch, connection, painting etc. as required.Make anchor/Polycab/Havells.

Supplying and fixing Suitable PVC box on surface or in recess, including providing and fixing 3 pin 5/6 amps socket outlet and 5/6 amps piano type switch, connection, painting etc. as required.Make anchor/Polycab/Havells.

Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/ wooden block including connection etc as required

Supplying of prewired LED tube light 20W LUMEN output 2000lm 6500K Product code PANASONIC PBTM02203 or equivalent to ISI standard.(Havells/Panasonic/Polycab) or Equivalent to ISI Standarad.

Installation, testing and commissioning of pre-wired, LED FITING of all types, complete with all accessories and tube etc. directly on ceiling/ wall, including connection with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.

Supplying and fixing following rating, four pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB /RCCB /Isolator)

12 way, Double door

16 way, Double door

Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.

63 Amps, 4 Pole Isolator

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Single Pole MCB

Earthing with copper earth wire plate 600mm x 600mm x 3mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. with charcoal/coke and salt as required.

Proving and fixing 25mm x 5mm copper strip in 40mm dia G.I pipe from earth electrode including connection with brass nut, bolt, spring, washer excavation and re-filling etc. as required.

Providing and fixing 25mm x 5mm strip on surface or in recess for loop earthing as required.

Supplying and fixing of AC HEAVY DUTY wall mounting fan (600mm sweep)( MAKE USHA DOMINAIRE WALL FAN ) with high speed swing and build in regulator with all accessories etc as required. ( Make: Bajaj /Usha/ Orient/ Crompton or equivalent to ISI standard).

Supplying and fixing of aesthetically designed recessed Square/Round shaped polycarbonate 20W LED fixture similar to Havells/ AMAZE round 20W LED 6000K Havells Cat. No. LHEWEKP PL1WO20 or Endura Linear LED 20W 6K (Ordering Code-LHDD01102674) its equivalent to ISI standard.

Supplying and fixing of aesthetically designed recessed Round / Square shaped, 600 mm x 600 mm size polycarbonate 30W LED fixture similar to Havells/ AMAZE round 30W LED 6000K Havells Cat. No. LHEWEKP PL1WO30 or Endura Linear LED 30W 6000K (Ordering Code-LHDD01102674) its equivalent to ISI standard.

Supplying of A.C. Ceiling fan (1200mm sweep, 5 Star Rating, Energy efficient FAN) USHA ENERGIA 50W suitable for operation on 230 Volts, single Phase, 50Hz, A.C Supply including 300mm long rod and without regulator as required. (Make: Bajaj/ Usha/ Orient/Crompton or equivalent to ISI standard).

Supplying and fixing stepped type electronic fan regulator (Shocket type)on the switch box including connections etc. as required.Make : anchor/polycab/havells etc or equvalent to ISI standard.

Installation, testing and commissioning of ceiling fan, including down road and wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc. as required.

Supplying of Exhaust fan (Metallic Fan)0f 300mm sweep (Make: Havells/Orient/Bajaj/Crompton) or equivalent to ISI Standard.

Installation of Exhaust fan in the existing openinf, including making good the damage, connection, testing, commissioning etc. as required.

Upto 450 mm sweep

Supplying, Installation, testing and commissioning of indoor type floor mounted cubical panel board made of not less than 1.0 mtr X 0.70 mtr X 0.50 mtr. non extendable type L.T - 3 phase 440V , 100A with both side open i/c front double hang shutter with locking arrangement made of 2 mm thick CRCA sheet in different compartment to accommodate various sizes of switch gear, busbar i/c supplying and fixing of following items i/c inter connection with 10 sq. mm copper cable. The panel should have inner earthing, one coat of primer and 2 coat of finishing water proof paint & danger plate etc.as required and its four legs made of equal angle 40 mm x 40 mm x 4 mm and embeded in the groung at the depth of 50 .00 cm with in cement concrete 1: 3 : 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) etc. as required.

MCCB 100 A/TPN (Four Pole) -25 KA breaking capacity with an adustable thermal settings --- 01 No.

Analog Ammeter (0 to 100 A) - 01 No.

Analog Voltmeter (0 to 500 V) - 01 No.

C.T. Coil, Class "B", with ratio of 100/5A - 03 Nos.

Indicating lamp with backup fuse (RYB) - 01 Set.

MCCB- 200 A/TPN (Four pole) 16 KA,breaking capacity - 01 Nos.

MCCB- 63 A/TPN (Four pole) 10 KA,breaking capacity - 02 Nos.

MCCB - 40 A/ TPN (Four Pole)- 10 KA, breaking capacity - 01 Nos.

Copper bus bar strip of size 40 X 5 X 600 mm length for RYBN - 01 Set

Rewirable procelain fuse unit with neutral link 100A (RYBN) - 01 Set

Inter connection with 10 Sq.mm PVC copper cable etc. as required.

Complete set including installation charges. (Make: Havells/L&T/Legrand) or equivalent to ISI Standard.

Supplying & Installation of Industrial Power Plug & Socket for almost all 3-phase power plug have an earth(Ground) connection, but may not have a neutral as 3-phase ;loads such as motor or Air Conditioner do not need the neutral, with 4 prongs( earth and 3-phases). Socket with neutral L21-30(30A) & L21-20(20A) boh of which have five pin(earth, neutral & X,Y ,Z phases). Rated operational voltage 20-25 volts, network frequency 50/60 Hz, having contacts pin material stainless steel, sleeve: nickel plated brass, Springs: Stainless steel, cable X-section 1-2.5 sq.mm ABB Industrial power plug & socket having 32A, 440V, 50/60 Hz, IP67, 3P+E with sleeve in 3 O'clock position as required.

5 pin, 32A, 440V, 50/60Hz Power plug & Socket.

Supplyig and fixing of 12 or more module Modular type PVC Electrical switch Boards for domestic and Industrial use with high quality Energy efficient rectangular white or other colour and wall mounted heat resistant of 500 Ohms ,shockproof, premium quality and long term durable PVC Electrical Switch Boards of Dimensions: (220 X 160 X 45)mm etc. as required or equivalent to ISI Standard. Make:( Anchor/Havells/Legrand/Polycab or equivalent to ISI Standard).

Supplying and fixing of new generation energy saving enviroment friendly long life 15 W LED street light made up of pressure dia cast aluminium housing with high power LED as light source and embeded PC cover having top opening seprate driver compertment with IP65 PROTECTION AND ik07 IMPACET RESISTENCE (MAKE : Polycab CAT No.PUBO506109 ) along with its Mountning (GI PIPE 20mm) (Make: Bajaj /Havells /Orient/Crompton or equivalent to ISI standard).

Supplying and fixing of new generation energy saving enviroment friendly long life 30 W LED street light made up of pressure dia cast aluminium housing with high power LED as light source and embeded PC cover having top opening seprate driver compertment with IP65 PROTECTION AND ik07 IMPACET RESISTENCE (MAKE : Polycab CAT No.PUBO506109 ) along with its Mountning (GI PIPE 32mm) (Make: Bajaj /Havells /Orient/Crompton or equivalent to ISI standard).

Supplying and fixing brass batten/ angle holder including connection etc. as required.

Supplying and fixing call bell/buzzer suitable for single single phase, 230 volts, complete as required.

Supplying of LED Lamp 9W (MAKE : WIPRO TEJAS 9W ) (Make: Bajaj/ Havells /Usha /Orient/Crompton or equivalent to ISI standard).

Supplying of LED MIRROR LIGHT 5W 450 LUMEN (PHILIPS ASTRE LINE). (Make: Bajaj/Havells/Crompton) or equivalent to ISI Standard.

Supplying ,Tesing and commissioning of clamp type hook in 40mm Dia Truss Pipe for installation of high way lights etc as required.

Supplying and fixing of wooden meter board size 400mmx200mmx20mm, Base: 30mmx25mm etc. as required.

Supplying and fixing of dry type Electrolytic Capacitor for ceiling fan of range between 2.5 to 4.0 mfd, capacitors tolerance ± 5%, operating temperature -25 to 85 degree celcius, rated frequency 50-60 Hz with voltage classification of 370-440V etc. as required. Make: (Rubycon/KEMET/NICHICON/Panasonic or equivalent to ISI Standard).

S B SHARMA (BID ID -53508)

ST.GEORGE CONSTRUCTIONS (BID ID -53626)

BHAGWAN SINGH (BID ID -53459)