SPECIAL REPAIR TO BOUNDARY WALL AND PROVN OF LOW BUDGETED WORKS UNDER AGE B/R-III OF GE(S) MEERUT CANTT

Amount

Taking down cement plaster of any description from brick or stone wall etc. including raking out joints, hacking for key, scrubbing down with water etc. complete all as specified and directed.

Demolition of brick work built in cement mortar including all quoins, arches, pillars etc, complete all as specified and directed

Demolition of PCC of any description and any position not otherwise specifically provided complete all as specified and directed.

Dismantling posts/struts (wood, steel or RCC) any section including taking out embedded portion from concrete/brick masonry etc and making good disturbed ground complete all as specified and directed .

Material and labour for PCC 1:4:8 type D2 using 40mm graded crushed stone aggregates as in foundation, filling and mass concrete complete all as specified and directed.

Material & labour for brick work with fly ash bricks built in CM 1:6 with sub class B, brick straight or curved on plan exceeding 6m mean radius complete all as specified and as directed.

Material & labour for brick work with sub class B bricks built in CM 1:6 straight or curved exceeding 6m mean radius except bricks (old bircks shall be used after cleaning) complete all as specified and directed.

Material and labour for PCC(1:2:4) Type B-1 (using 20mm graded crushed stone aggregate) as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, hold fast, kerbs water troughs and the like including weathering, slightly rounded or chamfered angles and throating complete al as specified and directed.

Material and labour for 15mm thick rendering in cement mortar 1:4 on fair faces of brick wall or concrete surfaces of roof finished even and smooth complete all as specified and directed.

Supply and fix mild steel work as in posts and struts in fencing including cutting tops to shape as directed drilling holes notching for wire etc complete all as specified and directed.

Material and labour for preparation of new steel surfaces of any description not otherwise described, over 10cm in width or girth and applying two coats of synthetic enamel paint over and including one coat of red oxide primer complete all as specified & directed.

Material & labour for preparation of newly plastered surfaces of walls and applying two coats of cement base paint over a coat of primer complete all as specified and directed.

Material and labour for applying one coats of exterior emultion paint (weather proof) over prepapred surface of walls complete all as specified and directed.

Supply & fix galvanized 2 strand steel barbed wire 2.24 mm dia of barbed with 2mm dia barbs at 75mm spacing and straining and fixing to any type of standard rails straining bolts including securing or tying at crossing with and provn of galvanized MS wire staple or steel pins etc (each line wire to be measured) complete all as specified & directed.

Use and waste of formwork to side of concrete foundation, footing, base of column, raft and raft beams, sides and soffits (if any) of foundation and plinth beams, and similar works vertical or to batter etc for rough finished surfaces of concrete complete all as specified and directed.

Use and waste of formwork to sides of concrete pillars, , posts, struts, piers, columns etc for rough finished surfaces of concrete complete all as specified and directed.

Material and labour for providing formwork to faces of walls, retaining walls, abutments and similar work including attached pillasters, buttresses etc vertical or to batter rough finished surfaces of concrete flat complete all as specified and directed.

Material and labour RCC M 25 Type B1 using 20mm graded stone aggregate as in foundations, including rafts, footings, foundation beams, plinth beams, base for columns, etc and mass concrete complete all as specified and directed.

Material and labour for providing reinforced cement concrete design mix M-25 (using 20 mm graded crushed stone aggregates) as in walls, retaining walls, beasement walls, ballast walls and the like; any thickness; above top of footings; including attached pilasters and buttresses complete all as specified and directed.

Material and labour for providing reinforced cement concrete M 25 (Design mix) as in columns, pillars, piers, posts and struts complete all as specified and directed.

Material & labour for TMT Bars 10mm dia and over cut to length bent to shape required inculding cranking bending spirally hooping for columns hooking ends etc and binding with and including mild steel wire annealed less than 0.9mm dia or securing with clips complete all as specified and directed.

All as per item No 21.00 above but 6mm to 8mm dia for striups complete all as specified and directed.

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft/ loose soil complete all as specified and directed.

Excavation in trenches not exc 1.50m wide and not exc 1.50m in depth for foundation etc or for manholes etc not exceeding 10 sqm on plan and not exc 1.5 m in depth and getting out in soft/loose soil all as specified and directed.

Returning filling in including spreading levelling and well ramming in soft/loose soil complete all as specified

Removing excavated materials n exc 50 mtrs and deposited where directed at a level n exc 50 mtr where directed n exc 1.50 m above the starting point complete all as specified and directed

Supply and fix MS framed work as in doors or gates of angle or other section with gussest plates, rails, braces, etc, complete drilled for fixing of steel sheeting or other covering doors etc, to be prepared for hanging and sliding with and including either hooks and hinges or steel hanging door fitting and fixing complete confirming to gde Fe 410-w.

Dismantling structural steel work incl doors gates in any position all directed by Engr-in-Charge.

Material and labour for granite machine cut 10 to12mm thick black coloured bedded and jointed with grey cement slurry and pointed in white cement with admixture of pigment to match including cutting and polishing as on columns or pillars /columns over and including 15mm thick rendering in cement mortar 1:4 complete all as specified and directed.

Supply and fix in repair 15 mm bore stop cock/angle cock, cast copper alloy, with long shank, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron or for union including CP flange complete all as specified and directed.

Supply & fixing PVC connections of 450mm long suitable for 15mm dia iron pipe incl PTMT nuts complete all as specified & directed.

Material and labour for cutting holes in brick wall in cement mortor for inserting holdfast and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 type B-1 as required) complete all as specified and directed.

Supply and fix 15mm bore GI tubing medium grade with all fittings and fixed to walls or laid on floor complete all as specified and directed

All as per item No 33.00 above but 20 mm bore complete all as specified and directed

Supply and fix mild steel framed work angle iron fixed in walls as in cooler stand in GF and FF embedded in PCC 1:2:4 type B1 using 20mm graded crushed stone aggregate including cutting holes 04 Nos for each cooler stand complete all as specified and directed by Engr-in-Charge.

Material and labour for point wiring with 1.5 Sqmm nominal cross sectional area, single core, 1100 Volts grade, stranded, FRLS PVC insulated, unsheathed, copper conductor cable in and including PVC concealed conduit 20 mm dia or higher size , medium grade complete with all PVC conduit accessories/fittings, brass screws, washers etc, sunk zinc coated pressed steel terminal boxes with 3mm thick plastic laminated sheet top cover concealed in wall with continuous earth wire of size 1.5 Sqmm nominal cross sectional area, single core, PVC insulated stranded copper conductor cable, unsheathed and connected to common earth and earth dolly complete all as specified and directed for one 3 pin, 05/06 Amps socket outlet point on independent board controlled by one, one way 05/06 Amps switch.

Supply and fix switch piano flush type, 05/06 Amp single pole, one way 240 volts complete all as specified and directed by Engineer-in-Charge.

Supply and fix socket outlet 3 pin, 05/06 Amp 240 volts complete all as specified and directed by Engineer-in-Charge.

AR Enterprises

vibha associates

Jain Engineering Works

Jay Ambay Enterprises

SHAKTI CONSTRUCTION CO

Rajneesh Jain

NK CONSTRUCTION

m/s gupta construction

CHAUDHARY FURNITURE HOUSE