REPAIR TO STEEL CHAIRS, TABLES AND CERTAIN STEEL FURNITURE AT ABOHAR AND FAZILKA MIL STN

Amount

CHARPOY GI/IP: Removing of old unservicable existing elbows and S & F new GI elbows 32mm dia ISI Mark all as specified & directed

Removing of old unserviceable broken checknuts and S & F new GI check nuts for 32mm GI pipes ISI Marked all as specified & directed

Removing of existing unseviceable long rails from Charpoy GI pipe and S & F new long rails made out of GI pipe 32mm bore medium grade as per existing shape & size complete as specified & directed .

Removing exsting damaged short rails and fixing short rails to charpoy after conversion from retrieved old long rails duly threaded at both ends and fixing the same as per existing shape & size complete all as directed .

Removing exsting damaged legs and fixing legs after conversion from retrieved old short rails duly threaded at one end and another side welding with 3mm thick MS sheet base and mild steel brackets of required size, shape for fixing MNF set all as shown on drawing and as directed .

M & L for welding to broken / cracked joints of charpoy GI pipe 32 mm dia (i.e) short rail, long rail, legs etc) by gas welding as per existing design rest all as specified and directed by Engineer-in-Charge.

Removing exsting unserviceable plywood from charpoy GI pipe and tightening entire frame and supply and fix 12mm thick plywood of BWR grade commercial of size 1980 x 900mm (Make : Archid /century /Greenply) fixed with flat head nut of size 5mm dia 60mm long, bolt with washer (Total 06 Nos per charpoy) including drilling holes in ply and steel frame of charpoy . Rest all as specified and directed by GE/Engr-in-Charge.

Chair Varandah : M & L for repair / fixing of broken parts of chair varandah by welding (Gas Welding) as existing with 20mm dia MS Conduite pipe where ever required as directed.

M & L for preparation of surfaces and painting of chair varandah with two coat of synthetic enamel paint white as specified and directed.

Removing of old exsting cane and recanning of chair varandah with new 4mm width 0.60mm thick cream colour plastic cane of approved quality as specified in drg and as directed.

Removing of old unserviceable PVC seat and back from chair varandah and S&F new PVC seat and back 4mm thick weight not less than 1.85 Kgs for both seat and back having 4 x 10mm thick ribs moulded complete all as specified and as directed by Engineer-in-Charge Make: Amko/Cello/Harmony

Supply and Fix new hard rubber shoes superior quality (as approved) of required size to chair varandah as directed.

REPAIRS TO CHAIR CB STEEL WITH ARMS AND WITHOUT ARMS: Removing of old unserviceable back frame of chair CB steel with arms and supply and fix new back frame made out of seasoned teakwood duly canned as per trade pattern. The chair shall be fixed with FI 3mm thick 14 X 25mm clips 02 Nos each on either side of back duly welded and also making holes to back frame centre to centre by drilling machine for fixing back frame with steel pipes by required size screws for extra support as directed.

Removing of old unserviceable seat frame of chair CB steel with arms and supply and fix new seat frame made out of seasoned teakwood duly canned as per trade pattern. The chair shall be fixed with FI 3mm thick 14 X 25mm clips 02 Nos each on either side of seat duly welded and also making holes to seat frame centre to centre by drilling machine for fixing seat frame with steel pipes by required size screws for extra support as directed.

Removing of old unserviceable hand rest and supply and fix new hand rest made out of well seasoned teakwood with required size screws. The hand rest shall be french polished with black colour all as specified, directed and as shown on drawing.

Removing of old unserviceable back frame of chair CB steel with out arms and supply and fix new back frame made out of seasoned teakwood duly canned as per trade pattern. The chair shall be fixed with FI 3mm thick 14 X 25mm clips 02 Nos each on either side of back duly welded and also making holes to back frame centre to centre by drilling machine for fixing back frame with steel pipes by required size screws for extra support as directed.

Removing of old unserviceable seat frame of chair CB steel with out arms and supply and fix new seat frame made out of seasoned teakwood duly canned as per trade pattern. The chair shall be fixed with FI 3mm thick 14 X 25mm clips 02 Nos each on either side of seat duly welded and also making holes to seat frame centre to centre by drilling machine for fixing seat frame with steel pipes by required size screws for extra support as directed.

M & L for preparation of surfaces and painting of chair CB Steel With Arms with two coat of synthetic enamel paint Olive Green. All as specified and directed.

M & L for preparation of surfaces and painting of chair CB Steel With out Arms with two coat of synthetic enamel paint Olive Green. All as specified and directed.

ALMIRAH LARGE STEEL WITH SHELVES: Removing unsv legs of almirah and S&F new legs made out of 1mm thick MS sheet as existing by welding / revitting as per drg and as directed.

Removing of unsv shelves from almirah Large steel. S& F of new shelves made of 1.00mm thick MS sheet of same shape & size as existing

Removing of UNSV 3 way locking device. S&F complete new locking device of same shape & size as existing and as per drg.

Removing of UNSV handle from almirah large steel. S&F new CP handle 150mm long as approved and directed.

Removing of old UNSV locks. S&F new brass lock 6 levers to almirah as approved .

M & L for de-rusting, denting, scrapping, filling with putty including preparation of old steel surfaces and applying synthetic enamel paint of required colour internally and externally by spray painting complete all as specified and as directed by Engr-in-Charge

ALMIRAH MEDIUM STEEL WITH SHELVES: Removing unsv legs of almirah and S&F new legs made out of 1mm thick MS sheet as existing by welding / revitting as per drg and as directed.

Removing of unsv shelves from almirah medium steel. S& F of new shelves made of 1.00mm thick MS sheet of same shape & size as existing

Removing of UNSV 3 way locking device. S&F complete new locking device of same shape & size as existing and as per drg.

Removing of UNSV handle from almirah med steel. S&F new CP handle 150mm long of approved make.

Removing of old UNSV locks. S&F new brass lock 6 levers to almirah as approved .

M & L for de-rusting, denting, scrapping, filling with putty including preparation of old steel surfaces and applying synthetic enamel paint of required colour internally and externally by spray painting complete all as specified and as directed by Engr-in-Charge

TABLE OFFICE OFFICER: Removing unsv top of table and S&F new top to table office officer steel made out of 18mm thick preleminated particle board with 6mm thick teak wood beading edging alround the top.

Removing of old UNSV drawers from table office Officer steel and S&F new drawers made of 1.00mm thick sheet of same shape & size as existing.

Repairing frame of table with new 25mm square MS tube of 1.6 mm thick by arc welding where ever required as directed by Engr-in-Charge

Removing of UNSV locks from table office Officer steel and S&F of new brass locks of 6 lever with duplicate key of approved quality as approved by GE/Engr-in-Charge.

Material & labour for painting to the frame of table with one coat of synthetic enamel paint olive Green all as specified and directed by Engineer-in-charge

TABLE OFFICE CLERK STEEL: Removing unsv top of table and S&F new top to table office clerk steel made out of 18mm thick prelaminated particle board with 6mm thick teak wood beading edging alround the top.

Removing of old UNSV drawers from table office clerk steel and S&F new drawers made of 1.00mm thick sheet of same shape & size as existing.

Repairing frame of table with new 25mm square MS tube of 1.6 mm thick by arc welding where ever required as directed by Engr-in-Charge

Removing of UNSV locks from table office clerk steel and S&F of new brass locks of 6 lever with duplicate key of approved quality as approved by GE/Engr-in-Charge.

Material & labour for painting to the frame of table with one coat of synthetic enamel paint olive Green all as specified and directed by Engineer-in-charge

TABLE 3' X 2' WITH DRAWER STEEL: Removing unsv top of table and S&F new top to table steel made out of 18mm thick prelaminated board with 6mm thick teak wood beading edging alround the top.

Removing of old UNSV drawers from table 3' x 2' steel and S&F of new drawers made of 1.00mm thick sheet of same shape & size as existing.

Repairing frame of table with new 25mm square MS tube of 1.6 mm thick by arc welding where ever required as directed by Engr-in-Charge

Material & labour for painting to the frame of table with one coat of synthetic enamel paint olive Green all as per specified.

TABLE 3' X 2' WITH OUT DRAWER STEEL: Removing unsv top of table and S&F new top to table steel made out of 18mm thick prelaminated board with 6mm thick teak wood beading edging alround the top.

Repairing frame of table with new 25mm square MS tube of 1.6 mm thick by arc welding where ever required as directed by Engr-in-Charge

Material & labour for painting to the frame of table with one coat of synthetic enamel paint olive Green all as per specified.

TABLE 3' X 3' STEEL: Removing unsv top of table and S&F new top to table steel made out of 18mm thick prelaminated board exterior grade with 6mm thick teak wood beading edging alround the top.

Repairing frame of table with new 25mm square MS tube of 1.6 mm thick by arc welding where ever required as directed by Engr-in-Charge

Material & labour for painting to the frame of table with one coat of synthetic enamel paint olive Green all as per specified.

LOCKER BED SIDE STEEL : Removing unsv legs of locker and S&F new legs made out of 1mm thick MS sheet as existing by welding / revitting as per drg and as directed.

Removing of unsv shelves from locker bed side steel. S& F of new shelves made of 1.00mm thick MS sheet of same shape & size as existing

Removing of UNSV hasp and staple of locker and S&F new hasp and staple of same shape & size as existing and as per drg.

Removing of UNSV handle from locker bed side steel. S&F new steel handle 100mm long of approved make.

Removing of old UNSV hanging rod S&F new hanging rod CP of 20mm dia to locker approved .

M & L for de-rusting, denting, scrapping, filling with putty including preparation of old steel surfaces and applying synthetic enamel paint of required colour internally and externally by spray painting complete all as specified and as directed by Engr-in-Charge

CHAIR EXECUTIVE REVOLVING STEEL: (a) Removing old unsv seat of chair executive and S&F new seat made out of 12 mm thick hot pressed ply wood upholstered with fabric & moulded polyurethane foam with PVC lipping all around all as existing and as directed

(b) Removing old unsv back of chair executive and S&F new back made out of 12 mm thick hot pressed ply wood upholstered with fabric & moulded polyurethane foam with PVC lipping all around all as existing and as directed

(c) Taking out old unsv castors wheel from executive chair and S & F new twin wheel castors as per existing size and shape complete all as specified and as directed by Engr-in-Charge

(d) Removing unsv gas lift and S&F new gas lift of 100mm stroke length and gas pressure of 300n force as existing.

CHAIR WRITING STEEL: (a) Taking out old unsv cantilever type MS frame from chair and S & F new cantilever type ms tubular frame made out of 25mm x 10mm sec as per existing size and shape complete all as specified and as directed by Engr-in-Charge

(b) Removing old unsv seat of chair steel and S&F new seat made out of 12 mm thick hot pressed ply wood upholstered with fabric & moulded polyurethane foam with PVC lipping all around all as existing and as directed

(c) Removing old unsv back of chair steel and S&F new back made out of 12 mm thick hot pressed ply wood upholstered with fabric & moulded polyurethane foam with PVC lipping all around all as existing and as directed

(d) Removing unsv armrest and S&F new one piece armrest made of black integral skin polyurethane with MS insert to the chair as existing with appropriate size bolt and nuts as specified and as directed.

CHAIR COMPUTER: (a) Removing old unsv seat of chair computer and S&F new seat made out of 12 mm thick hot pressed ply wood upholstered with fabric & moulded polyurethane foam with PVC lipping all around all as existing and as directed

(b) Removing old unsv back of chair computer and S&F new back made out of 12 mm thick hot pressed ply wood upholstered with fabric & moulded polyurethane foam with PVC lipping all around all as existing and as directed

(c) Taking out old unsv castors wheel from chair computer and S & F new twin wheel castors as per existing size and shape complete all as specified and as directed by Engr-in-Charge

(d) Removing unsv gas lift and S&F new gas lift of 100mm stroke length and gas pressure of 300n force as existing.

PAINTING OF STEEL FURNITURE: M & L for de-rusting, denting, scrapping, filling with putty including preparation of old steel surfaces and applying two coats of synthetic enamel paint of required colour internally and externally by spray painting complete all as specified and as directed :- (a)Side rack steel 3 spaces

Trestle store room steel

Rack steel 1830x760x1905mm

Rack 6 tier steel

SUDESH ENTREPRISES

SHIVANI ENTERPRISES