Provision of covered shed for bridging eqpt alongwith hardstanding at middle lake of CME

Amount

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in hard/dense soil etc. complete as directed.

M&L for excavation in trenches in any type of soil, n exc 1.5 m wide and not exceeding 1.50 m depth for foundations etc. n. exc 10 sqm on plan and getting out in hard / dense soil etc. complete all as specified & directed.

M&L for excavation in trenches in soft/disintegrated , n exc 1.5 mwide and not exceeding 1.50 m depth for foundations etc. n. exc 10 sqm on plan and getting out in soft/disintegrated soil etc. complete all as specified and directed.

M& L for cement concrete 1:2:4 type B - 2 using 40 mm graded crushed stone aggregate as in foundation filling and mass concrete in post holes etc. complete all as specified and directed.

M&L for excavation in trenches in hard rock, n exc 1.5 m wide and not exceeding 1.50 m depth for foundations etc. n. exc 10 sqm on plan and getting out hard rock etc. complete all as specified and directed.

M & L For reinforced cement concrete type B- 1,1:2:4 ( using 20 mm graded stone aggregate ) as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc. basement slabs under-reamed piles and mass concrete etc. complete all as specified and directed.

M & L for reinforced cement concrete type B- 1,1:2:4 ( using 20 mm graded stone aggregate ) as in columns , etc. complete all as specified and directed.

M & L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work vertical or to batter etc. including finished surface fair & even etc. complete all as specified and directed.

M & L For formwork to sides of pillars, posts, struts, piers, columns and stanchions including finished surface fair & even etc. complete all as specified and directed.

S & F for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips etc. complete all as specified and directed.

S & F for mild steel TMT bars 5 mm to 10 mm dia., cut to length, bent to shape required, in stirrups, spacers and binders and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips etc. complete all as specified and directed.

M&L for PCC block masonry with solid blocks, exc 10 cm in width and set in CM 1:4 precast cement concrete block of type C-1 with 1:3:6 (using 20 mm graded stone aggregate) etc. complete all as specified and directed.

Returning, filling in, including spreading, levelling watering and well ramming in layer not exc 25 cm in soft/loose soil

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point

Rendering 15mm thick on fair face of brick work or concrete surfaces in CM 1: 4 with finished the surface even & smooth without using extra cement.etc. complete all as specified and directed.

Rendering 15mm thick on fair face of brick work or concrete surfaces in CM 1: 6 with finished the surface even & smooth without using extra cement etc.complete all as specified and directed.

M&L for prepration of newly plastered surfaces of walls and applying two coats of cement base paint over a coat of cement primer on walls etc complete all as specified and directed.

M&L preparing newly plastered surfaces of wall and applying of three coats of white wash on walls complete all as specified and directed.

M & L For 150 mm thick Soling (or sub base) with broken boulders or quarried stone, inter stices filled, surface well rammed etc. complete all as specified and directed by Engr - in - charge

M & L For Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and ammed including watering etc. complete all as specified and directed by Engr - in - charge

M & L for Hardcore of gauge exc 63mm but n exc. 100 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rolled/rammed to a true surface

M&L for 75mm thick PCC type D-2 (1:4:8) using 40 mm graded stone aggregate as in sub base etc complete all as specified and directed

M&L for 50 mm thick, type B-1, 1:2:4 (20mm graded stone aggregate) as in sub base etc complete all as specified and directed.

S &F For glass dividing strips, 3 mm thick, including width of strip 38 mm and inserted in position, conform to design etc. complete all as specified and directed.

Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 , etc. complete all as specified and directed.

S&F steel work of grade Fe - 410 W ( Gde E -250) quality B inroof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc.complete all as specified & directed. Note : Steel frame work will include post, truss, purline, rafter, runner, bracings etc.

S&F steel work of grade Fe - 410 W ( Gde E -250) quality B mild steel plates (plain or chequered) 5 mm or over in thickness in available sizes complete all as specified and directed.

S & F For Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and directed. Note:- Colour of sheets as approved by Engr-in-charge/ GE

S &F For Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and directed. Note:- Colour of sheets as approved by Engr-in-charge/ GE

S&F 75mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 etc complete all as specified and as directed.

S&F 1mm thick Mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required, complete all as specified and directed.

S & F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded etc complete all as specified and directed.

S&F 4 mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane etc complete all as specified and directed.

Preparation of new or previously untreated surfaces of iron of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint over and including a of red oxide primer complete all as specified and directed

M&L for point wiring for light/fan/Bell with FRLSH cable 1.5 sqmm PVC insulated (red for phase and black for neutral) unsheathed, multi stranded copper conductor 1100 volt grade in and incl not less than 25mm PVC conduit with all accessories and 1.50 sqmm green in colour PVC copper conductor cable for earth continuity connected to common earth dolly incl PVC box surface/ flush type with PVC sheet for mounting fittings such as switches, sockets, fan regulators, etc complete all as specified and directed for one light/fan /bell point controlled by one switch & making good to disturbed surface of wall etc for the following :-

One light point controlled by one switch

One 3 pin socket outlet, 5 amps, independent, with cables 1.5 sq mm size

S & F switch piano, flush type, single pole one way 5 amps complete all as specified and directed.

S&F Socket outlet 3 pin, 6A, flush type complete all as specified and directed.

S & F ceiling rose, 3 terminal PVC/polycarbonate isolated body, surface bakelite 65 x 50 mm, 3 terminal incl PVC square block complete all as specified and directed.

Supply and fixing LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.

Supply and fixing bldg security light 35 Watt 230 V AC outdoor type with high pressure die cast aluminium hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection including GI bracket complete all as specified and directed.

S&F MCB distribution board double door 240 volts 4 way with 200 amps rated bus bar and making good to disturbed surfaces of floors walls complete all as specified and directed.

S & F MCB SP 6 to 32 Amps, 230 V AC complete all as specified and directed.

S & F MCB SPN 40 Amps, 230 V, AC complete all as specified and directed.

Earthing complete with galvanised steel earth plate electrode 60×60cm.× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion

Excavation in trenches n. exc. 1.5m wide and n exc. 1.5m in depth for taking out/laying cables in soft/loose soil all as directed.

Supply, laying and testing cable XLPE insulated screened PVC bedded galvanised steel strip or wire armoured, electric power cables ( heavy duty) with stranded aluminium conductor 1100 volts grade cross sectional area 2 core 10 Sqmm all as specified and directed.

Supply & Laying of Telerex DWC (Double Wall corrugated) HDPE pipe ISI marked of outer dia of 50 mm and inner dia 38 mm polythylene with smoooth inernal and profiled external surface for non pressue under ground cable incl couplers & bends complete all as specified.

Aishwarya Constructions

AJINKYA VIKRAM GAIKWAD

vishalconstruction

Mukund Engineers and Contractors

R K Construction

M/s DEVRATAN ENTERPRISES

ShreHari Civil Enginneering and Contractors