Provn of Furniture storage accn for BSO Yard under GE Bharatpur

Amount

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out soft/loose soil complete all as specified and directed.

Excavation in trenches, n exc 1.5m wide and n exc 1.5m in depth, for foundation etc and getting out in soft/loose soil complete all as specified and directed.

M&L PCC 1:4:8 type-D2 (40mm graded aggregate) as in foundations, filling and mass concrete.sub base as in floors complete all as specified and directed.

Returning Filling in,including spreading, levelling, watering and well ramming in layers, not exc 25 cm in soft/loose soil complete all as specified and directed.

Removing excavated material n exc 50 m and depositing where directed at level n exc 1.5m above the starting point complete all as specified and directed.

Spreading and levelling in layers n exc 25 cm thick well ramming including watering as required complete all as specified and directed.

M&L RCC Design Mix( M- 25 ) using 20mm graded stone aggregate for Foundations, including rafts, footings, foundation b eams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

M&L RCC Design Mix( M- 25 ) using 20mm graded stone aggregate for column/pillrs,piers,post and struts complete all as specified and as directed.

M&L RCC Design Mix( M- 25 ) using 20mm graded stone aggregate for Beams, cantilevers, bressummers, lintel beam etc complete all as specified and as directed.

M&L for Reinforced cement concrete Design Mix( M- 25 ) using 20mm graded stone aggregate as in chajja complete all as specified and directed.

M&L Brick work with Fly ash bricks straight or curved on plan exc 6m mean radius built in CM 1:4 complete all as specified and directed.

M&L for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batte complete all as specified and directed.

M&L Form work to sides and soffits of floor or roof beams , beam haunchings, girders, bressummers, lintels, cantilevers,shelves including supports, overhangs, etc also splays between floors and beams, etc for rough finished flat surfaces of concrete complete all as specified and directed.

M&L Formwork to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and directed.

M&L Form work to edges of concrete flats, treads,breaks in floors, window cills, concrete railing, openings in concrete walls, floors and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls,horizontal or sloping and similar work exc 10cm but n exc 20 cm wide for rough finished surfaces of concrete complete all as specified and directed.

M&L Formwork to chullah hoods, chajjas on flat surface troughs and similar items including edges complete all as specified and directed.

S&F MS deformed or twisted bars,10 mm dia and over, cut to length, bent to shape required, including cranking,bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed)not less than 0.9mm dia or securing with clips complete all as specified and directed.

Deformed or twisted TMT bars 6 to 8mm dia cut to length bent to shape required incl cranking bending and binding with mild Steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

M&L Rendring 15mm thick in cement mortar 1:4 on fair faces of brick/concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L Rendring 15mm thick in cement mortar 1:6 on fair faces of brick/concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L rendering 10mm thick in CM 1:4 on concrete surfacves/ chajja/ ceiling, etc finished even and smooth without using extra cement complete all as specified and directed.

M&L for Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L 25mm thick PCC 1:2:4 type B1 (20mm graded stone aggregate) as in floor and finished rough to recive the floor tiles etc complete all as specified and directed.

M&L 75 mm thick PCC 1:4:8 type D-2 using(40mm graded stone aggregate) as in sub base of floors complete all as specified and directed.

M&L for Machine cut kota stone slab flooring 20-25mm thick over 15mm thick screed base in CM(1:6) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L for Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over 15mm thick screed base in CM(1:6) complete all as specified and directed.

S&F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and as directed.

S&F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded complete all as specified and as directed.

S&F Galvanized mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm complete all as specified and as directed

S&F 3mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and directed.

M&L Anti Termite Treating the bottom and sides of excavation at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed.

M&L for Anti Termite Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified and directed.

M&L Anti Termite Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed.

M&L Anti Termite Treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed.

S&F 30mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed complete all as specified and directed.

S&F Mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc complete drilled for fixing of steel sheeting or other covering. Doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging also fastening and fixing of Fe 410-W (Gde-E-250) quality -A) complete all as specified and as directed.

S&F rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates Fe 410-W (Gde-E-250) quality A complete all as specified and as directed.

S&F Mild steel Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc Fe 410-W (Gde-E-250) quality A complete all as specified and as directed.

S&F Mild steel Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment complete all as specified and directed.

M&L for Painting to new steel or steel based surfaces of any description, not otherwise described over 10cm width or girth including preparation of surfaces, priming with red oxide zinc chrome primer (one coat) & finishing with two coats of synthetic enamel paint complete all as specified and as directed.

M&L for Painting to new steel or steel based Surfaces of any description, n.exc 10cm in width or girth including preparation of surfaces, priming with red oxide zinc chrome primer (one coat) & finishing with two coats of synthetic enamel paint complete all as specified and as directed.

M&L for Painting to new wood or wood based surfaces of any description, not otherwise described over 10cm width or girth including preparation of surfaces, priming with pink primer (one coat) & finishing with two coats of synthetic enamel paint complete all as specified and as directed.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated, semi corrugated or trapezoidal profile steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa, as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa, as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

M&L Prepration of new plastered surfaces of wall and applying two coats of cement based paint over a coat of alkali resistant primer complete all as specified and directed.

M&L Prepration of new plastered surfaces of wall and applying three coats of white wash over a coat of primer complete all as specified and directed.

M&L for 50mm thick PCC 1:3:6 type C1 using 20mm graded stone aggregate as in floor/plinth protection laid in suitable panels finished even and fair all as spd . 6mm Joints should be filled with bitumen mastic filling comprising of one part of heated bitumen 85/25 or 80/100 gde and three part of sand ( all by weight) complete all as specified and directed.

S&F aluminium anodized barrel tower bolt of extruded section of size 200 mm long complete all as specified and directed.

S&F Aluminium anodized handle handles 150mm long complete all as specified and directed.

S&F aluminium alloy anodised sliding door bolt with hasp and staple (bolt type) & fixing clips of sheet, cast and extruded section & fixing bolt & sliding bolt of extruded section of size 300mm long complete all as specified and directed.

S&F 100 mm butt hinges , heavy duty weight ,cold roll mild steel complete all as specified and directed.

M&L for preperation of concrete /brick surface clean and firm,free from dust releasing agent,grease,wax,paint and other contaminant and wet the surface before applying of plaster and 20kg of polimer powder mix with 5-7 ltr water and applying 5mm thick on brick surface properly and all as specified and as directed by Engr-in-charge.Make:Ultra tech,Birla

Supply and laying 800 micron thick polythene filim laid over ground level up to the edge of plinth protection complete all as specified and as directed.

Surface excavation n.exc 30cm deep and avereging 15cm deep and getting out soft/loose or any type of soil complete all as specified and directed.

Material and labour hardcore of broken stone of gauge exc. 63mm & n. exc 100mm deposited spread and leveled in layers n.exc 15cm thick watered and well rammed to a true surface complete all as specified and directed.

Material and labour for PCC (1:3:6) Type C-2 using 40mm graded crushed stone aggregate as in sub base of floor 75mm thick finished even and fair without using extra cement complete all as specified and directed.

M&L for Sand for filling under floors ,spreading and levelling in layers 25 mm thick including watering and consolidation complete all as specified and as directed.

M&L for Machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and pigment complete all as specified and as directed.

M&L for factory made pre cast solid PCC block(1:2:4) type B1 using 20mm graded stone aggregate as in kerb stone of size 300x450x150mm machine made set in Cement and sand mortar complete all as specified and directed.

Supply & spread unwashed dry river sand for sand cushioning and covering the under ground cable in trenches complete all as specified and directed.. (Note :- Punning thickness shall be measured and paid only.)

M&L for brick protection with sub Class`B` bricks old size laid dry, flat over cable perpendicular across the cable in trenches complete all as directed.

Supply, laying, testing & commissioning LT XLPE insulated armoured (heavy duty) electric cable with stranded aluminium conductor 1100 volts grade (ISI marked) & laid in trenches/pipes or fixed on pole complete all as specified and directed of the following sizes:- (a) 10 Sqmm 2 core

(b) 16 Sqmm 4 core Note:- Excavation and earth work if requred shall be measured and paid seperately.

M&L galvanished light grade pipe of 40 mm dia fix on wall/ trenches complete all as specified and directed.

Boring of holes under road, pavement, hard standing by trenchless technology using necessary machine for laying under ground pipe upto 100mm dia complete all as specified and directed. Note :- GI pipe shall be measured and paid in concern Item

Earthing complete with Galvanised steel earth plate electrode 600 x 600 x 6 mm buried directly in the ground vertically to depth not less than 3 Mtr below the ground level with the top edge of earth plate, depth not less than 2.25 Mtr below the ground level connected to connected to galvanised earth strips 32x6mm by means of bolts, nuts and washers protected by GI tubing light grade 40 mm dia uptoTest point 20 mm dia watering pipe with funel & wire mesh, PCC pit in PCC 1:2:4 using 20 mm stone aggregates chamber 40 mm thick RCC cover slab (1:2:4) type B-1 using 20 mm graded stone aggregates complete all as specified and shown in electrical plate No.3 of SSR Part-I including earth work in any type of soil ,removal of surplus sil and providing charcol dust & salt layers all around the earth plate upto 15 cm all as required specified & directed

M&L point wiring complete with 1.5 Sqmm 02 x single core multistranded copper conductor of 1100 volts grade PVC pre insulated FRLS and unsheathed cable enclosed in PVC conduit pipe with all PVC accessories such as Tee, bend, collar, elbow, square junction box etc fixed on the concealed surface of wall/ceiling by means of PVCsleevel/dash fastners with cadmium plated screws including suitable size of PVC boards/ existing sunken box for mounting fittings like switches, sockets, fan regulator etc including 1.5 Sqmm insulated but unsheathed copper earth continuity conductor to common earth and connedcted to earth dolly complete all as specified and directed for the following :- (a) One light point controlled by one way switch.

(b) One fan point controlled by one way switch.

(c) One 3 pin 6 Amp socket point outlet on the same board with other switches

(d) One 3 pin 6 Amp socket point outlet on the independent board

All as per item No 67 above but with multi stranded copper conductor cable 2.5 Sqmm size for 3 pin 16 Amps socket point outlet on independent board including 2.5 Sqmm copper cable PVC insulated FRLS unsheathed copper continuous earth wire including connecting to common earth dolly complete all as specified and directed.

S&F ceiling rose surface bakelite 50 x 40 mm three terminal ISI marked including suitable size of PVC board complete all as specified and directed.

S&F socket outlet 2 in 1, 3 pin 5 Amps multi purpose flush type 230 volt complete all as specified and directed.

S&F switch socket combinatin 2 in 1, 3 pin 5 and 15 Amp flush type multi purpose 230 volt complete all as specified and directed.

S&F switch piano flush button single pole one way 6 Amps 230 volt grade complete all as specified and directed.

S&F step type electronic fan regulator EME type 100 watt complete all as specified and directed.

Distribution board factory made and tested made of sheet metal enclosure powder coated suitable for mounting the MCB 240 volt complete all as specified and directed. of the following DBs :-. (a) 8 way SPN with 200 amps rated busbar 240 volts (double door type).

S&F MCCB, MCB with GI hardware fixed in DB's of the undermentioned type and rating. (a) MCB SP 240 volts 10-32 Amps

(b) MCB SPN 40 Amps, 240 volt

S&F Linear LED T8 tubular lamp of 20 watt with extruded aluminium body,PC diffuser and inbuilt driver including compact batten suitable for LED T8 lamps , complete with all accessories internally pre-wired and including connecting to ceiling rose with three core flexible copper conductor cable of size 1Sqmm complete all as specified and directed. Cat Part No:DIJB12LT8-20 and Lamp -LGT8-20-865-2, Make Crompton or equivalent in Bajaj/Havells/Philips/Crompton.

Earthing complete with Galvanised steel earth plate electrode 600 x 600 x 6 mm buried directly in the ground vertically to depth not less than 3 Mtr below the ground level with the top edge of earth plate, depth not less than 2.25 Mtr below the ground level connected to connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts and washers protected by GI tubing light grade 20 mm dia uptoTest point 20 mm dia watering pipe with funel & wire mesh, PCC pit in PCC 1:2:4 using 20 mm stone aggregates chamber 40 mm thick RCC cover slab (1:2:4) type B-1 using 20 mm graded stone aggregates complete all as specified and shown in electrical plate No.3 of SSR Part-I including earth work in any type of soil ,removal of surplus sil and providing charcol dust & salt layers all around the earth plate upto 15 cm all as required specified & directed ( Note:- Up to 7.5 Mtr length of pipe of 40 mm dia and GI strip shall be deemed to be included in unit rate quoted by tenderer GI pipe and GI strip beyond 7.5) will be measured separately under respective item.

S&F 25 watts LED street light fitings new generation energy saving, environmental friendly, long life, versatile pressure die cast aluminium IP66 with 10KV surge protection road way, luminaire with high power LED as light source with warranty option of 5 years and suitable drivers etc and connecting with 4.0 sq mm multistranded aluminium conductor PVC insulated twin core weather proof cable from fittings to over head lines or to the jucntion box and fixing to complete all as specified and directed , Make :- Crompton Cat NoLST-20-CDL-M or equivalent in wipro, Bajaj, Philips.

S & F street light GI bracket of 0.6 mtr long made out of 40mm dia light grade GI pipe bend to shape of 120 degree end welded at required including 02 Nos MS clamp of FL 40 x 6mm including nuts bolts & washers complete necessary fixing arrangements on pole as directed.

S&F exhaust fan of 380 mm sweep 900 rpm with suitable size of MS louvers duly painted , connecting wire PVC insulated twisted flexible 0.5 sqmm copper conductor including all standard accessories complete all as specified and as directed. . Make: Havells Model: Turbo Force SP,or equivalent in bajaj/cromption/polar etc

AMIT RISHABH BUILDERS PVT LTD