Providing additional 1X10MVA, 110/11kV Power Transformer at 110/11kV Hulikal substation in Hosanagara Taluk Shivamogga District on PTK basis

Karnataka Power Transmission Corporation Limited

WORK INDENT NO: KPTCL/2025-26/SS/ WORK_INDENT3385

Providing additional 1X10MVA, 110/11kV Power Transformer at 110/11kV Hulikal substation in Hosanagara Taluk Shivamogga District on PTK basis. Note: 10MVA PTR and 11kV switchgear will be supplied by KPTCL for above work.

TECHNO - COMMERCIAL SHEETS

NOTE* For detailed scope of the work please refer Bid Documents.

BIDDERS TO READ CAREFULLY

THE FOLLOWING DOCUMENTS [DULY SIGNED BY AUTHORISED PERSON, WHEREVER NECESSARY] ARE TO BE UPLOADED IN KPPP PORTAL AND BANK GUARANTEE TOWARDS EMD OVER AND ABOVE RS.10.00LAKH AS PER ANNEXURE-II OF THE BID DOCUMENT SHALL BE SENT IN ORIGINAL TO CHIEF ENGINEER ELECTY., Transmission (Operations) Zone, KPTCL, Hassan SO AS TO REACH THIS OFFICE AFTER THE LAST DATE OF SUBMISSION OF BID AND ON OR BEFORE THE DATE & TIME NOTIFIED FOR OPENING OF TECHNO COMMERCIAL BIDS FAILING WHICH THE BID WILL NOT BE OPENED. 1) NO DEVIATION CERTIFICATE (SCHEDULE-16). 2) EMD/BID SECURITY AS DETAILED IN CLAUSE NO. 13 of ITT. 3) BANK GUARANTEE TOWARDS BALANCE EMD/BID SECURITY issued either by a Nationalized/Scheduled Bank. (For the balance EMD above Rs. 10Lakhs ) (SCHEDULE-17) - as detailed in Clause No. 13 of ITT-The Bidder shall scan the Bank Guarantee towards EMD and upload the same in the prescribed format in the slot specified for “EMD and Tender Fee Payments” in the e-procurement portal to enable the owner for verification of EMD BG at the time of opening of Techno Commercial Bid, failing which the offer will be rejected 4) LETTER OF UNDERTAKING (SCHEDULE-18). 5) CONSORTIUM AGREEMENT (IF APPLICABLE-SCHEDULE-19). 6) POWER OF ATTORNEY (SCHEDULE-20). 7) ANY OTHER AGREEMENTS / UNDERTAKINGS /SELF DECLARATIONS SPECIFIED IN THE TENDER.

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

BID PROPOSAL SHEET

WORK INDENT NO: KPTCL/2025-26/SS/ WORK_INDENT3385

Providing additional 1X10MVA, 110/11kV Power Transformer at 110/11kV Hulikal substation in Hosanagara Taluk Shivamogga District on PTK basis. Note: 10MVA PTR and 11kV switchgear will be supplied by KPTCL for above work.

Bidder's Name & Address alongwith GSTIN no. :

Bid Proposal Reference :

Person to be contacted :

E-Mail Address:

The Chief Engineer (Elect.), Transmission(Operations) Zone, KPTCL, Prasarana Bhavana, Third Floor, Santhepete, B.M.Road, Hassan-573201

Providing additional 1X10MVA, 110/11kV Power Transformer at 110/11kV Hulikal substation in Hosanagara Taluk Shivamogga District on PTK basis. Note: 10MVA PTR and 11kV switchgear will be supplied by KPTCL for above work.

a) * We have uploaded bid as individual Bidder. (Indicate Name of the Individual Bidder)

b) * We have uploaded bid in Consortium with the following Bidders. (Key in Consortium) VOID

Name of the Consortium Partner Scope / Participation of each Consortium Partner

(* Fill-up whichever is applicable)

1 We, the undersigned Bidder, having read and examined in detail the specifications and all the Bidding documents of the said work and hereby propose to design, manufacture/fabricate, shop test, supply on FOR site basis, and carry out the erection, testing and commissioning including civil, structural and architectural works for

Providing additional 1X10MVA, 110/11kV Power Transformer at 110/11kV Hulikal substation in Hosanagara Taluk Shivamogga District on PTK basis. Note: 10MVA PTR and 11kV switchgear will be supplied by KPTCL for above work.

2 PRICES AND VALIDITY :

2.1 We declare that the Prices stated in our Proposal are in accordance with subject bid documents including Clause No.40 of "Conditions of Contract (CC)" and Clause No.11 of Instruction to Tenderers (ITT) of Bid Documents. We further declare that all Ex-works price/CIF components of Spares, Maintenance and Testing Equipments and other charges viz., Freight and Insurance, Type Test charges and other charges stated in our proposal shall be as per the Tender conditions. All the Price and other terms and conditions of this Proposal are valid during the Performance of the Contract.

2.2 All Taxes and Duties, such as Custom Duties on imports, Levies, Surcharge/Cess etc., if any, applicable on the transaction are included in the Bid Price and shall be to Our account and the Owner is not having any liability whatsoever on this account, whatever may be the contrary elsewhere in the Bid documents. However the component of Taxes & Duties included in the Bid Price are separately indicated in Schedule - 2 for TDS purpose. We further confirm that our Bid Prices as quoted in Schedule-I, include all import Duties and levies including Licence fees lawfully payable by us on imported items and all other Taxes, Duties and Levies applicable on Bought-out Components, Materials, Equipment and other items and confirm that any such Taxes, Duties and Levies additionally payable shall be to our account. We further confirm that no Sales Tax in any form shall be payable by Owner either for Bought-out items which are despatched by our Sub-Suppliers directly to the Project Site or for items Supplied directly by us.

2.3 We declare that we have noted and considered Clause No.39 of Conditions of Contract (CC ), Clause No. 11.11 of Instruction to Tenderers (ITT) of Bid Documents regarding Taxes and Duties and quoted our Prices accordingly. We further agree for TDS as per Statutory stipulations.

2.4 The Bid Prices, the Price components of the various items in the Scope of Supply, Erection including Testing & Commisisoning, Civil and Mandatory spares is quoted in Itemwise Financial Bid in KPPP Portal for this proposal..

3 CONSTRUCTION OF THE CONTRACT : We, declare that we are making the Offer on the basis of Single Contract for the entire Scope of the Package in accordance with Clause No.26 of Instruction to Tenderers (ITT) of Bid Document.

4 We having studied Clause No.39 of Conditions of Contract (CC ), Clause No. 11.11 Instruction to Tenderers (ITT) of Bid Documents , relating to Tax and we hereby, declare that if any income-tax, surcharge on income tax or any other corporate tax is attracted under the law, we agree to pay the same.

5 Bid Security/ EMD : We have enclosed a Bid Security through e-Payment mode for a sum of Rs.10.00Lakhs and remaining amount of Rs.................................................. ( above Rs.10 Lakhs) in the form of Bank Guarantee in original and two copies of the original valid for a period of 225 days from the date of opening of bids, and liable to be forfeited in accordance with Bid Documents. (Mode of Payment towards EMD is as detailed in NIT/CLAUSE NO. 13 of ITT.)

We have also ensured that the above Bid Guarantee furnished by us is in line with the Bid Documents and complete in respect of following :

1. Value of Non judicial Stamp Paper purchased in the name of executing Bank is as per Stamp Act.

2. Power of Attorney Number and Date as well as Signature and Full Name and Designation of Executant along with Bank's Stamp are there.

3. Signature, Full Name, Designation and address of Witness are there.

4. Completed Mailing address of the Head Office of the Bank is indicated.

6.1 We declare that the Works shall be performed strictly in accordance with the Specifications and Documents except for the variations and Deviations, all of which have been detailed out exhaustively in the following Schedules, irrespective of whatever has been stated to the contrary anywhere else in our Proposal.

a Commercial Deviations Schedule Schedule - 5

b Technical Deviations Schedule Schedule - 6

6.2 We further confirm that Specified Stipulation of following Clauses are acceptable to us and No Deviation / Exceptions are taken on any account whatsoever in the following Clauses.

a. Terms of payment Clause No. 37 of Conditions of Contract (CC) & Clause No.8 of Special Conditions of Contract-SCC.

b. EMD/Bid Security Clause No.6, Section :1, Invitation for Tenders (IFT) and Clause No.13, Section :2, Instruction to Tenderers (ITT)

c. Contract Performance Guarantee Clause No.29, Instruction to Tenderers (ITT)

d. Penalty for delay Clause No.41 of Section-5 : Conditions of Contract (CC)

e. Price Basis/ Price adjustment Clause No. 40 of Section-5 :Conditions of Contract (CC)

f. Defects Liability Period/Guarantee Clause No.10 of Special Conditions of Contract (SCC) and Section 6 : Contract data

g. Work Schedule Clause No.17 of Conditions of Contract-CC

h. Taxes and Duties Clause No.11.11 of Instruction to Tenderer (ITT)

Further, we agree that additional conditions, if any, found in the Proposal Documents other than those stated in Deviation Schedules, save that pertaining to any rebates offered, shall not be given effect to.

7 PERFORMANCE GUARANTEE ; We declare that the ratings and performance figures of the equipment to be supplied and erected by us are guaranteed. The Guaranteed particulas of different equiment in our Scope are enclosed in Data Requirement Sheets.

8 BID PRICING : We further, declare that the Prices stated in our Proposal are in accordance with your ITT & SCC and all other relevant clauses of Bid Documents.

9 PRICE ADJUSTMENT : We declare that the Prices quoted by us are in accordance Clause No. 40 of Section-5 :Conditions of Contract (CC)

10 SPECIAL TOOLS AND TACKLES : We have given a list of Special Tools and Tackles in Schedule - 7 and Prices thereof are included in our lumpsum Bid Price. We further agree that any items of Special Tools and Tackles, though not included in the aforesaid list, but required for effective Erection, Testing, Commissioning & Operation of the Equipments of Substations shall also be furnished by us, at no extra cost to you.

11 ADDITIONAL INFORMATION : In addition to the information called for in these Proposal Sheets, we have included with this Proposal, additional information as listed in Schedule - 8. We further confirm that such additional information does not imply any additional deviation beyond those covered in Schedule - 5 & 6 and in case of any contraction between these additional information and other provisions of Bid, the later will prevail.

12 QUALIFICATION DATA : We confirm having submitted the Qualification Data, as required by you in your Bid Documents in e-Procurement Portal along with this Proposal. Further we have filled in the information for Qualification Requirements in Schedule 9. In case you require any further information in this regard, We agree to furnish the same in time.

13 WORK SCHEDULE : If this Proposal is accepted by you, we agree to submit Engineering Data, Provide Services and complete the entire Work from time to time, in accordance with Schedules indicated in the Proposal. We fully understand that the Time Schedule stipulated in this Proposal is the essence of the Contract, if awarded. The completion schedule of the various Major Key Phases of the Work is indicated in Schedule - 11.

14 CONTRACT PERFORMANCE GUARANTEE ; We further agree that if our Proposal is accepted, we shall provide an irrecoverable Contract Performance Guarantee, of value equivalent to Five Percent (5%) of the Contract Price plus additional security for unbalanced tenders in accordance with Clause 25.5 & 29 of Instructions To Tenderers (ITT) and Clause No. 43 of the Conditions of Contract (CC) of the tender valid up to the end of ninety (90) days after the end of the Contract Warranty Period in the form of .........................................................................................................................................................................................................................................................(Please specify the form of Guarantee) in your favour and enter into a formal agreement with you within Twenty (20) days from the date of issue of Letter of Intent to award the Contract .

16 CHECK LIST : We have included a Checklist duly filled in Schedule 21

17 We, hereby, declare that only the Persons or Firms interested in this Proposal are named herein as Principals and that no other Persons are interested in the Proposal or in the Contract to be entered into, if we are awarded the Contract, and that this proposal is made without any connection with any other Person, Firm or Party likewise submitting a Proposal and that this Proposal is in all respect for and in good faith, without collusion or fraud.

18 We declare, in case our bid is accepted, that until a formal Contract is prepared & executed, this bid together with your written Letter of Intent to Award the Contract thereof and your notification of award /Letter of Intent to Award the Contract shall constitute a binding contract between us. We further understand that you are not bound to accept the lowest or any bid you may receive.

Thanking you, we remain,

Yours faithfully,

Place Printed Name

Business Address Country of Incorporation (State or Province to be indicated)

Name and Address Principal Officer

Karnataka Power Transmission Corporation Limited

SHEET FOR TECHNO COMMERCIAL OPENING (Unpriced)

Providing additional 1X10MVA, 110/11kV Power Transformer at 110/11kV Hulikal substation in Hosanagara Taluk Shivamogga District on PTK basis. Note: 10MVA PTR and 11kV switchgear will be supplied by KPTCL for above work.

WORK INDENT NO: KPTCL/2025-26/SS/ WORK_INDENT3385

FILL ONLY IN LIGHT BLUE COLOURED CELLS.

Bidder's Name & Address alongwith GSTIN no. : To,

The Chief Engineer (Elect.), Transmission(Operations) Zone, KPTCL, Prasarana Bhavana, Third Floor, Santhepete, B.M.Road, Hassan-573201

We declare that in terms of Clause no. 11 of ITT & all other relevant clause of Bid documents, the following are our lumpsum price in Rupees for the entire scope of work as specified in the Specifications and Documents.( Inclusive of all Taxes & Duties).

Total Lumpsum Price : ( In Figures) Note: Fill as "YES" against this column in case Prices are indicated in the Item-Wise Bid Financial Offer in figures

Place Designation

Name of the Company

Karnataka Power Transmission Corporation Limited

SCHEDULE- 2 B - STATEMENT OF COMMERCIAL TERMS AND CONDITIONS

SHEET FOR TECHNOCOMMERCIAL OPENING

WORK INDENT NO: KPTCL/2025-26/SS/ WORK_INDENT3385

Providing additional 1X10MVA, 110/11kV Power Transformer at 110/11kV Hulikal substation in Hosanagara Taluk Shivamogga District on PTK basis. Note: 10MVA PTR and 11kV switchgear will be supplied by KPTCL for above work.

Details of payments made in the form of Credit card/Debit card/NEFT/RTGS/OTC (over the counter) as per the tender conditions should be keyed in against column no. 3 (a) . BG Amount, BG No. and date, Name and address of the bank issuing the BG, validity of the BG should be keyed in against column no. 3 (b) .

FILL ONLY IN LIGHT BLUE COLOURED CELLS.

Bidder's Name & Address alongwith GSTIN no. : To,

The Chief Engineer (Elect.), Transmission(Operations) Zone, KPTCL, Prasarana Bhavana, Third Floor, Santhepete, B.M.Road, Hassan-573201

STATEMENT OF COMMERCIAL TERMS AND CONDITIONS

Sl. No. Particulars Details

1 Bid proposal form uploaded

2 No deviation certificate uploaded

3. a) EMD / Bid Security Bids shall be accompanied by bid security (EMD); 1) Up to Rs.10Lakh The following modes of payment will be provided as a part of e-Payment services. • Credit Card/Debit Card • Net Banking • NEFT/RTGS • Over-the-Counter (OTC) • IMPS For further detail regarding mode of e-payment of EMD in e-procurement platform, contact e-procurement cell, Government of Karnataka.

b) EMD amount above Rs.10Lakh by Bank Guarantee

4 Validity of the Bid.

5 Qualifying Requirements.

6 Financial capability

8 Taxes & Duties.

9 Completion Schedule

10 Defects Liability Period/Guarantee

11 Payment Terms

Place Designation

Name of the Company

Karnataka Power Transmission Corporation Limited

SCHEDULE - 3B(i) - Supply portion

WORK INDENT NO: KPTCL/2025-26/SS/ WORK_INDENT3385

Providing additional 1X10MVA, 110/11kV Power Transformer at 110/11kV Hulikal substation in Hosanagara Taluk Shivamogga District on PTK basis. Note: 10MVA PTR and 11kV switchgear will be supplied by KPTCL for above work.

Sl. No. Item Description Unit Qty Unit rate in Rs. Total Amount in Rs.

A1 Nitrogen injection fire extinguishing system- Supplying, erection & commissioning including Civil Engineering works. Soak pit etc., as per the recommendations of the supplier of the fire fighting system for power transformer below 100 MVA No 1 1,141,635.00 1,141,635.00

A2 CIRCUIT BREAKER :SF6 circuit breaker with semi-pneumatic/ pneumatic operated/ with spring type operating mechanism including mounting structure with rigid bi-metallic terminal connector suitable for Moose/Drake ASCR and mounting structure. 145kV ,3150A,40kA SF6 CB For 110 kV Transformer Nos. 1 774,000.00 774,000.00

A3 ISOLATORS : Isolators including marshalling box and suitable terminal connectors, as required as per technical specification with Solid core cylindrical post Insulators. 110 kV, 1250 A, 40 kA class double break manually operated isolators with terminal connector suitable for Moose/Drake ACSR

1 upright mounting type without Earth Switch (Live Point Height 4600mm)Suitable for Bay width 10.4Mtrs Set 2 321,860.00 643,720.00

2 upright mounting type without Earth Switch (Live Point Height 6350mm) Suitable for Bay width 8.2Mtrs Set 3 329,120.00 987,360.00

Terminal connectors for Isolators shall be as follows: Rigid type suitable for Moose/ Drake ACSR-3 Nos Flexible type suitable for 63mm Al.pipe-3Nos

II 11kV Isolators

1 11kV Isolator, single break 400A,25kA capacity with roaster switch, with rigid bimetallic terminal connector suitable for coyote ACSR set 4 14,956.00 59,824.00

2 11kV Isolator, double break 400A,25kA capacity with rigid bimetallic terminal connector suitable for coyote ACSR for Capacitor Bank. set 1 21,260.00 21,260.00

A4 CURRENT TRANSFORMER: Current transformers including marshalling boxes, Single phase, Oil filled outdoor type with rigid bimetallic terminal connectors suitable for Moose/ Drake ACSR conductor

1 110 KV Class. 40 KA, CT of Ratio 200-100/1-1-1A for Transformer Core1=Vk-400V, Rct 2ohm at @200/1A,Accuracy class PS-Dist/Dif Core2= 10VA, Accuracy class 0.2s-Metering Core3= 30VA , 5P20- Backup, Nos 3 150,000.00 450,000.00

2 11KV Class,25kA NCT of ratio 1200-800/1-1-1 A for REFR Protection ( similar rating & ratio as that of incomer of 11KV Switchgear ) with terminal connector suitable for 2 nos of copper flats as per technical specifications. Note: 1)All the CTs in each kV class shall be of one and the same make for interchangeability & reliability of per:formance. 2)The make and characteristics of llkV NCT should be the same as that of the incomer CT of 1lkV Switchgear. To ensure this, the 11kV procured from the supplier of 11kV svñtchgear only. Nos 1 63,000.00 63,000.00

A5 SURGE ARRESTORS: (Porcelain housing) Metal Oxide Gapless type with rigid bimetallic connectors suitable for Moose/Drake ACSR

1 96 kV, 1O KA, SM type-For Transformer Nos. 3 52,000.00 156,000.00

A6 Control and Relay panel complete

1 For Power Transformer 110/11KV Note: 1. All the C&R panels and the associated panels shall be of one and the same make for uniformity and interchangability of components. 2. The DLMS protocol energy meter/ electronic tri- vector meter with ABT features has to be provide on both HV side & LV side of C&R panel. No.s 1 631,620.00 631,620.00

A7 Station Structures: (Including bolt and nuts) Note:1).Weight of station structures and G.I Mounting structures shall be as mentioned in prevalling SR A)110KV side station structure fabricated out of galvanized mlid steel including Bolts and Nuts

1 Station towers (Verticals 1T1) (1.054 MTX 4 No.s = 4.216 MT) Nos 04/4.126 130,001.04 520,004.16

2 Station beams (1B1) suitable for 8.2Mtrs bay width (0.553MT X 2No.s= 1.106MT) Nos 02/1.106 68,130.96 136,261.92

Note:The 1T1 tower and 1B1 beam shall be suitable for bay width of 8.2Mtrs

B) 11KV ODS and take off structure

1 Supplying & erection of Double pole structure with 9.5 Mts. RCC poles WL 300 Kgs for mounting 11 kV 400 A Roaster Isolators and 9 kV, 10 KA surge arrestor (3 No.} complete set . ( 2 Nos for Feeders ) Set 4 26,922.00 107,688.00

A8 MOUNTING STRUCTURES

1 110 KV Isolators. Live Point Height -4600mm (0.752 MT per Structure). No/MT 02/1.504 92,284.30 184,568.60

2 110 KV Isolators. Live Point Height -6350mm (0.982MT per Structure). No/MT 03/2.946 120,365.00 361,095.00

3 110KV Current transformer (0.158 MT per Structure). No/MT 03/0.474 19,525.40 58,576.20

4 11KV NCTs. (0.157 MT per Structure). No/MT 01/0.157 19,382.58 19,382.58

6 110 KV Potential transformer (0.148 MT per Structure). No/MT 03/0.444 18,284.58 54,853.74

5 96 kV Lightening arrestors. (0.116 MT per Structure). No/MT 03/0.348 14,380.58 43,141.74

6 110 KV Pedestal insulators for Bus (0.14 MT per Structure). No/MT 15/2.100 17,350.14 260,252.10

7 110 KV High pedestal insulators for transformer. (0.15 MT per Structure). No/MT 06/0.900 18,632.48 55,897.44

8 11KV UG cable terminating structure for LV side of transformer-(0.072 MT per Structure). No/MT 01/0.072 8,846.34 8,846.34

9 11KV GOS/UG cable terminating structure for 11 KV Capacitor Bank- (0.158 MT per Structure). No/MT 01/0.158 22,371.53 22,371.53

A9 BUS BAR FORMATION:

1 Drake ACSR Mtrs. 100 461.00 46,100.00

2 Coyote ACSR Mtrs. 60 164.00 9,840.00

A10 RIGID BUS WITH TAPS & CLAMPS :

1 Aluminium Tube conforming to 6340 WP of IS- 5082/1969 (BS1600 - Sch. 40) of following Nominal Diameter a) 75mm---110kV Main Bus Mtrs. 186 1,586.00 294,996.00

2 63mm Size for connecting isolator to Verticle Tap and also connecting equipment to equipment ---110kV side Mtrs. 36 1,452.00 52,272.00

3 Straight taps made of 75 mm Aluminium Tube (BS-1600) of 1750 mm vertical height for connecting 75mm tube on main bus to 75 mm tube on cross bus on 110 kV side with rounded off end. Nos. 6 3,736.00 22,416.00

4 Straight taps made of 63 mm Aluminium Tube (BS-1600) of 1750 mm vertical height for 75 mm main bus to 63mm tiube on cross bus on 110 kV side with rounded off end. Nos. 6 3,736.00 22,416.00

5 Post Insulator Clamp suitable for 75 mm Aluminium pipe and Post Insulators Solid Core type

a)Rigid Type Nos. 9 1,868.00 16,812.00

b)Expansion Type Nos. 3 5,322.00 15,966.00

c)Sliding Type Nos. 9 2,109.00 18,981.00

6 Corona Bell Suitable for Aluminium pipe of Size of 75mm on 110kV Nos. 9 679.00 6,111.00

7 End Cap for 63mm Aluminium Tube Nos. 6 617.00 3,702.00

A11 Insulators:

1 Post Insulator Solid Core insulator 110KV Class, 1 Unit/Stack No 21 12,116.00 254,436.00

2 Disc Insulators with hardwares: Single Suspension string using 9 units of each 11KV, 90KN Disc Insulator along with Suspension Clamp and hardware suitable for DRAKE ACSR [ Single Suspension Clamps + 9 units of 90KN Disks = 1,523 + (593x 9) = Rs 6860] String 3 6,887.00 20,661.00

1 C-Type wedge connector suitable for DRAKE-DRAKE (110KV Bus) No.s 6 2,718.00 16,308.00

A13 A.C Distribution Box (outdoor):AC distribution box single front type , 6 terminals, 1200X 1350X 300mm, 1 I/C of 100A, MCCB 20KA + 6 O/G MCB 16A + 1 O/G of 100A, HRC fuse No.s 1 72,600.00 72,600.00

A14 LT Power armoured UG cable as per specification.

a) 1.1 KV Class 4 X25 sq.mm Copper cable, with glands/ lugs/ ferrules Mtrs. 120 866.00 103,920.00

A14 COPPER CONTROL CABLE:- 1.1 kV Grade PVC Insulated armoured Copper Control Cable of sizes with lugs/ferrules/Gland as per technical specifications.

A16 11KV U.G. Cable with the required cable terminations at both ends.

1 11kV class 1 X 1000 Sq mm U.G. Cable XLPE (from 110/ 11kV transformers to 11kV switchgear) Mtrs. 300 1,523.00 456,900.00

2 11kV class 3 X 240 Sq mm U.G. Cable XLPE (from 11kV switchgear to 11kV take off DP structure) Mtrs. 500 1,656.05 828,024.00

3 Heat shrinkable type Cable termination kits suitable for 1 x 1000 Sq.mm XLPE cable (Indoor type) Nos. 7 3,808.00 26,656.00

4 Heat shrinkable type Cable termination kits suitable for 1 x 1000 Sq.mm XLPE cable (outdoor type) Nos. 7 4,060.00 28,420.00

5 Heat shrinkable type Cable termination kits suitable for 3 x 240 Sq.mm XLPE cable (Indoor type) Nos. 5 4,691.00 23,455.00

6 Heat shrinkable type Cable termination kits suitable for 3 x 240 Sq.mm XLPE cable (outdoor type) Nos. 5 5,318.00 26,590.00

A16 CAPACITOR BANK: Design, Engineering, supply, erection, testing & commissioning of 2.9 MVAR, 12. l kV Capacitor Bank, star connected, Double Bank with internal fuses, terminal connectors with suitable neutral CT and station class LAs, 0.2% series reactor on neutral side with mounting structures for NCT, Capacitor Bank, station class LAs, Series reactor etc,. complete as per specification set 1 538,450.00 538,450.00

A17 Equipements for SCADA Communication

1 Multi Functional Transducer (MFT) 3 Phase-4wire self powered 0.2S Class including labour (market rate) No.s 6 4,875.00 29,250.00

2 Opto Coupler (220 or 110V DC,8i/p including labour (market rate) No.s 6 1,312.00 7,872.00

Cable supplying and laying

3 Current Cable- Copper core with C/S 4.0sq.mm multistand 4 Core Mtrs. 60 177.00 10,620.00

4 Voltage Cable- Copper core with C/S 2.5.0sq.mm multistand 4 Core Mtrs. 30 179.00 5,370.00

5 Single cable-Aramoud Copper Core with C/S 0.5sq.mm Multi stand 10 Core Mtrs. 60 143.00 8,580.00

6 Control Cable-Copper Core with C/S 1.5sq.mm Multistand 10 Core Mtrs. 30 155.00 4,650.00

A18 MISCELLANEOUS ITEMS

1 Rubber mats 1000 mm x 1000 mm x 10 mm size suitable for 15 kV class. Nos 1 1,900.00 1,900.00

2 Equipments name plates & earthing name plates including fixing at outdoor yard. Nos 24 416.00 9,984.00

Place Designation

Name of the Company

Karnataka Power Transmission Corporation Limited

SCHEDULE - 3B(ii) - ERECTION & DECOMMISSIONING

WORK INDENT NO: KPTCL/2025-26/SS/ WORK_INDENT3385

Providing additional 1X10MVA, 110/11kV Power Transformer at 110/11kV Hulikal substation in Hosanagara Taluk Shivamogga District on PTK basis. Note: 10MVA PTR and 11kV switchgear will be supplied by KPTCL for above work.

ERECTION & T & C PORTION

Sl. No. Item Description Unit Qty Erection charges in Rs. Total Amount in Rs. T&C Charges in Rs. Total Amount in Rs.

B1 Power Transformer: Power Transformer 10 MVA, 110/33-11 kV Delta/Star,Dyn11,3 Ph, 50 Hz, Core type winding with OLTC,RTCC Panel.etc., complete first filling of Transil Oil with 10% spare oil with Terminal connectors suitable for Drake ACSR on 110 KV Side and Drake ACSR or 110KV side and AAA C Moose /2 Nos of copper flat for each phase from LV side of Transformer to Cable at 11kV cable terminating structure with suitable support insulator on LV side of Transformer and 2 Nos of Copper flats from neutral terminal to earthmat through NCT along with neccessary support pin insulators.(35MT) Nos. 1 179,690.00 179,690.00 48,187.00 48,187.00

B2 CIRCUIT BREAKER :SF6 circuit breaker with semi-pneumatic/pneumatic operated/ with spring type operating mechanism including mounting structure with rigid bi-metallic terminal connector suitable for Moose/Drake ASCR and mounting structure.

B3 ISOLATORS : Isolators including marshalling box and suitable terminal connectors, as required as per technical specification with Solid core cylindrical post Insulators.

I 110 kV, 1250 A, 40 kA class double break manually operated isolators with terminal connector suitable for Moose/Drake ACSR

1 upright mounting type without Earth Switch (Live Point Height 4600mm)Suitable for Bay width 10.4Mtrs Set 2 8,701.00 17,402.00 1,301.00 2,602.00

2 upright mounting type without Earth Switch (Live Point Height 6350mm) Suitable for Bay width 8.2Mtrs Set 3 8,701.00 26,103.00 1,301.00 3,903.00

Terminal connectors for Isolators shall be as follows: Rigid type suitable for Moose/ Drake ACSR-3 Nos Flexible type suitable for 63mm Al.pipe-3Nos

II 11kV Isolators

1 11kV Isolator, single break 400A,25kA capacity with roaster switch, with rigid bimetallic terminal connector suitable for coyote ACSR set 4 1,214.00 4,856.00

2 11kV Isolator, double break 400A,25kA capacity with rigid bimetallic terminal connector suitable for coyote ACSR for Capacitor Bank. set 1 1,214.00 1,214.00

B4 CURRENT TRANSFORMER: Current transformers including marshalling boxes ,Single phase, Oil filled outdoor type with rigid bimetallic terminal connectors suitable for Moose/ Drake ACSR conductor

1 110 KV Class. 40 KA, CT of Ratio 200-100/1-1-1A for Transformer Core1=Vk-400V, Rct 2ohm at @200/1A,Accuracy class PS-Dist/Dif Core2= 10VA, Accuracy class 0.2s-Metering Core3= 30VA , 5P20- Backup, Nos 3 2,131.33 6,394.00 4,700.33 14,101.00

2 11KV Class, 25kA NCT of ratio 1200-800/1-1-1 A for REFR Protection ( similar rating & ratio as that of incomer of 11KV Switchgear ) with terminal connector suitable for 2 nos of copper flats as per technical specifications Nos 1 733.00 733.00 4,545.00 4,545.00

Note: 1)All the CTs in each kV class shall be of one and the same make for interchangeability & reliability of per:formance. 2)The make and characteristics of llkV NCT should be the same as that of the incomer CT of 1lkV Switchgear. To ensure this, the 11kV procured from the supplier of 11kV svñtchgear only.

B5 SURGE ARRESTORS: (Porcelain housing) Metal Oxide Gapless type with rigid bimetallic connectors suitable for Moose/Drake ACSR

1 96 kV, 1O KA, SM type-For Transformer Nos. 3 444.00 1,332.00

B6 Control and Relay panel complete

1 For Power Transformer 110/11KV Note: 1. All the C&R panels and the associated panels shall be of one and the same make for uniformity and interchangability of components. 2. The DLMS protocol energy meter/ electronic tri- vector meter with ABT features has to be provide on both HV side & LV side of C&R panel. No.s 1 5,959.00 5,959.00 42,973.00 42,973.00

B7 Station Structures: (Including bolt and nuts)

Note:1).Weight of station structures and G.I Mounting structures shall be as mentioned in prevalling SR A)110KV side station structure fabricated out of galvanized mlid steel including Bolts and Nuts

1 Station towers (Verticals 1T1) (1.054 MTX 4 No.s = 4.216 MT) Nos 04/4.126 5,723.00 24,128.17

2 Station beams (1B1) suitable for 8.2Mtrs bay width (0.553MT X 2No.s= 1.106MT) Nos 02/1.106 5,723.00 6,329.64

Note:The 1T1 tower and 1B1 beam shall be suitable for bay width of 8.2Mtrs

B) 11KV ODS and take off structure

1 Supplying & erection of Double pole structure with 9.5 Mts. RCC poles WL 300 Kgs for mounting 11 kV 400 A Roaster Isolators and 9 kV, 10 KA surge arrestor (3 No.} complete set . ( 2 Nos for Feeders ) Set 4 3,199.00 12,796.00

B8 MOUNTING STRUCTURES

1 110 KV Isolators. Live Point Height -4600mm (0.752 MT per Structure). No/MT 02/1.504 5,723.00 8,607.39

2 110 KV Isolators. Live Point Height -6350mm (0.982MT per Structure). No/MT 03/2.946 5,723.00 16,859.96

3 110KV Current transformer (0.158 MT per Structure). No/MT 03/0.474 5,723.00 2,712.70

4 11KV NCTs. (0.157 MT per Structure). No/MT 01/0.157 5,723.00 898.51

6 110 KV Potential transformer (0.148 MT per Structure). No/MT 03/0.444 5,723.00 2,541.01

5 96 kV Lightening arrestors. (0.116 MT per Structure). No/MT 03/0.348 5,723.00 1,991.60

6 110 KV Pedestal insulators for Bus (0.14 MT per Structure). No/MT 15/2.100 5,723.00 12,018.30

7 110 KV High pedestal insulators for transformer. (0.15 MT per Structure). No/MT 06/0.900 5,723.00 5,150.70

8 11KV UG cable terminating structure for LV side of transformer-(0.072 MT per Structure). No/MT 01/0.072 5,723.00 412.06

9 11KV GOS/UG cable terminating structure for 11 KV Capacitor Bank- (0.158 MT per Structure). No/MT 01/0.158 5,723.00 904.23

B9 RIGID BUS WITH TAPS & CLAMPS :

1 Aluminium Tube conforming to 6340 WP of IS- 5082/1969 (BS1600 - Sch. 40) of following Nominal Diameter a) 75mm---110kV Main Bus Mtrs. 186 96.00 17,856.00

2 63mm Size for connecting isolator to Verticle Tap and also connecting equipment to equipment ---110kV side Mtrs. 36 96.00 3,456.00

B10 Insulators:

1 Post Insulator Solid Core insulator 110KV Class, 1 Unit/Stack No 21 444.00 9,324.00

B11 A.C Distribution Box (outdoor): AC distribution box single front type , 6 terminals, 1200X 1350X 300mm, 1 I/C of 100A, MCCB 20KA + 6 O/G MCB 16A + 1 O/G of 100A, HRC fuse No.s 1 4,175.00 4,175.00

B12 LT Power armoured UG cable as per specification.

1 1.1 KV Class 4 X25 sq.mm Copper cable, with glands/ lugs/ ferrules Mtrs. 120 15.00 1,800.00

B13 COPPER CONTROL CABLE:- 1.1 kV Grade PVC Insulated armoured Copper Control Cable of sizes with lugs/ferrules/Gland as per technical specifications.

B14 11kV Switch Gear : 11 kV, 25kA,Metal clad VCB switcñgear 1600A for incomer & 1250 A for feeders) outdoor type, each comprising of 1I/C+4F+1CB+1BC+ 1AP {remote annunciation cum control panel )with CTs & PTs etc., completer as per technical specification. Note: 1. Simplex type Annunciator panel shall be provided for switchgear (consisting of incomer, feeders and bus coupler). 2.for Capacitor Bank: 'The Capacitor Bank panel shall be same as that of the 11 kV bank i.e. incomer panel in all respect.In addition to relays provided in the I/C, the following addition relays to be provided. i)Circulating current relay with timer. ii} Under voltage relay. iii)Timer relay. Set 1 2,081.00 16,648.00 8,039.33 64,314.64

B15 11KV U.G. Cable with the required cable terminations at both ends.

1 11kV class 1 X 1000 Sq mm U.G. Cable XLPE (from 110/ 11kV transformers to 11kV switchgear) Mtrs. 300 29.00 8,700.00

2 11kV class 3 X 240 Sq mm U.G. Cable XLPE (from 11kV switchgear to 11kV take off DP structure) Mtrs. 500 29.00 14,500.00

3 Heat shrinkable type Cable termination kits suitable for 1 x 1000 Sq.mm XLPE cable (Indoor type) Nos. 7 3,752.00 26,264.00

4 Heat shrinkable type Cable termination kits suitable for 1 x 1000 Sq.mm XLPE cable (outdoor type) Nos. 7 3,752.00 26,264.00

5 Heat shrinkable type Cable termination kits suitable for 3 x 240 Sq.mm XLPE cable (Indoor type) Nos. 5 2,658.00 13,290.00

6 Heat shrinkable type Cable termination kits suitable for 3 x 240 Sq.mm XLPE cable (outdoor type) Nos. 5 2,658.00 13,290.00

B16 Equipements for SCADA Communication

1 Multi Functional Transducer (MFT) 3 Phase-4wire self powered 0.2S Class including labour (market rate) No.s 6 1,555.00 9,330.00

2 Opto Coupler (220 or 110V DC,8i/p including labour (market rate) No.s 6 1,555.00 9,330.00

Cable supplying and laying

3 Current Cable- Copper core with C/S 4.0sq.mm multistand 4 Core Mtrs. 60 25.00 1,500.00

4 Voltage Cable- Copper core with C/S 2.5.0sq.mm multistand 4 Core Mtrs. 30 25.00 750.00

5 Single cable-Aramoud Copper Core with C/S 0.5sq.mm Multi stand 10 Core Mtrs. 60 25.00 1,500.00

6 Control Cable-Copper Core with C/S 1.5sq.mm Multistand 10 Core Mtrs. 30 25.00 750.00

B17 Earth Mat formation

1 Supplying and laying MS Flat 75 x 12mm flat welding and applying ACB paint to welded portion as per drawing/ standard if required (all other materials to be supplied by contractor) Rmtr. 978 839.00 820,542.00

2 Grounding of equipments with 50 x 6 mm G.I flat and connecting equipments to the earth mat/ ground pit including all connected works with all materials supplied by the contractor. Rmtr. 804 335.00 269,340.00

3 Providing 25mm dia, 1.05mtr. long Earthmat Spike of MS Rod including bending top 50 mm etc Nos 45 453.00 20,385.00

4 Providing C.I. Pipe of l00 mm ID 13mm thick 2.75 mtr. long with 2 part GI Flat 50x6mm clamp welded allround the pipe etc., including cost of excavation ( all materials supplied by contractor) Nos 24 16,283.00 390,792.00

5 Supplying and fixing 450mm dia x 450mm to height 1.5" to 2" Hume pipe collars for each pits. Nos 24 1,499.00 35,976.00

6 Bentonite clay for M.S Flat and Cast iron pipe Electrode KGs 9882 25.00 247,050.00

B18 MISCELLANEOUS ITEMS

1 Releasing and Re-Erection 110KV PTs Nos 3 2,131.33 12,787.98 4,732.33 14,196.99

2 Releasing and Re-Erection 110KV CTs Nos 3 2,131.33 12,787.98 4,700.33 14,100.99

3 Releasing and Re-Erection 110KV LA's Nos 3 444.00 2,664.00

Place Designation

Name of the Company

Karnataka Power Transmission Corporation Limited

SCHEDULE - 3B(iii) - Civil portion

WORK INDENT NO: KPTCL/2025-26/SS/ WORK_INDENT3385

Providing additional 1X10MVA, 110/11kV Power Transformer at 110/11kV Hulikal substation in Hosanagara Taluk Shivamogga District on PTK basis. Note: 10MVA PTR and 11kV switchgear will be supplied by KPTCL for above work.

Sl. No. Item Description Unit Qty Unit Rate in Rs. Total Amount in Rs.

B1 Construction of Embankment with approved materials deposited at site from roadway cutting and excavation from drain and foundation of other structures graded with desired compaction. (Royalty shall be recovered @ Rs. 60.00/m3) Cum 2747.00 119.00 326,893.00

B2 Earth work excavation for pipeline trenches in all kinds of soils by mechanical means as per drawing and technical specifications, including setting out,construction of shoring, strutting, barricading, caution lights, bracing, usingsight rails & bonding rods at every 100 mm wherever necessary as directed,removal of stumps and other deleterious matter, dressing of sides and levelling the bottom of trench to the extent required , utilising the available excavated earth locally for the work etc., and all other appurtenances complete in the following strata. (For Earth mat excavation) Cum 2658.00 262.00 696,396.00

B3 Earth work excavation for Foundation by mechanical means for all works & depth up to 3 m, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution lights, including dressing of excavated surfaces, disposing off or leveling the excavated earth or sorting & stacking the selected earth for reuse in a radius of 50 m and lift up to 1.5 m including Cost of labour, tools, usage of machinery & other appurtenances required to complete the work. In all kinds of soils Depth up to 3 m Cum 3749.00 102.00 382,398.00

B4 Refilling available earth around trenches/pipelines, cables in layers not exceeding 20 cms in depth, compacting each deposited layer by ramming after watering with a lead upto 50 m , and lift upto 1.5 m. Including cost of all labour complete as per specifications (For Earth mat bakfilling) Cum 1592.00 266.00 423,472.00

B5 Providing and laying in position plain cement concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed, laid in layers not exceeding 150 mm thickness, well compacted using plate vibrators, including all lead & lifts, cost of all materials of quality, labour, Usage charges of machineries, curing, and all the other appurtenances required to complete the work as per technical specifications. Mix 1:3:6 (M10) Using 20 mm nominal size graded crushed coarse aggregates Cum 166.00 6,147.00 1,020,402.00

B6 Providing and laying in position Reinforced cement concrete for all Foundation works. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticizers laid in finished layers, well compacted using needle vibrators, including all lead & lifts, cost of all materials, quality confirming to the requirements of relevant IS codes , labour, Usage charges of machinery, curing and all the other appurtenances required to complete the work as per technical specifications. M25 Design Mix Using 20 mm nominal size graded crushed coarse aggregates- For foundation (Raft of Columns,Retaining walls, Cable Ducts, Sump Tank,culverts,Drains,Equipment foundation) (3% considered for Form work) Cum 178.00 6,413.81 1,141,658.18

B7 Providing and laying in position Reinforced cement concrete for all Foundation works. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticizers laid in finished layers, well compacted using needle vibrators, including all lead & lifts, cost of all materials, quality confirming to the requirements of relevant IS codes , labour, Usage charges of machinery, curing and all the other appurtenances required to complete the work as per technical specifications. M25 Design Mix Using 25 mm nominal size graded crushed coarse aggregates- For Columns pedestal & column upto plinth beam ( 70% considered for Form work) Cum 6.00 10,585.90 63,515.40

B8 Providing and laying in position Reinforced cement concrete for all Super structures of building , Road works, Water works, Irrigation works & super structure works of bridges upto 3.50 m height. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticisers laid in layers, well compacted using needle vibrators. The cost includes all lead & lifts, cost of all materials, quality confirming to the requirements of relevant IS codes , labour, Usage charges of machinery, curing and all other appurtenances required to complete the work as per technical specifications. M25 Design Mix Using 20 mm nominal size graded crushed coarse aggregates - For Columns ( 70% considered for Form work) m3 9.00 11,447.80 103,030.20

B9 Providing and laying in position Reinforced cement concrete for all Basement & surface level works. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticizers laid in finished layers, well compacted using needle vibrators, including all lead & lifts, cost of all materials, quality confirming to the requirements of relevant IS codes , labour, Usage charges of machinery, curing and all the other appurtenances required to complete the work as per technical specifications. M25 Design Mix Using 20 mm nominal size graded crushed coarse aggregates-For Plinth beam CR building,PC Plinth beam,SWG PB( 50% considered for Form work) m3 7.00 9,556.50 66,895.50

B10 Providing and laying in position Reinforced cement concrete for all Foundation works. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticizers laid in finished layers, well compacted using needle vibrators, including all lead & lifts, cost of all materials, quality confirming to the requirements of relevant IS codes , labour, Usage charges of machinery, curing and all the other appurtenances required to complete the work as per technical specifications. M25 Design Mix Using 20 mm nominal size graded crushed coarse aggregates-For Retaining wall alround below CR building plinth beam bottom and Fencing poles,kerb stone ( 10% considered for Form work) Cum 10.00 6,849.70 68,497.00

B11 Providing and laying in position Reinforced cement concrete for all Sub-structure works. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticizers laid in finished layers, well compacted using needle vibrators, including all lead & lifts, cost of all materials, quality confirming to the requirements of relevant IS codes , labour, Usage charges of machinery, curing and all the other appurtenances required to complete the work as per technical specifications. M25 Design (1:1.5:3) Mix Using 20 mm nominal size graded crushed coarse aggregates-For RCC drains,Cable ducts,culverts,RCC R wall/Toe wall ( 35% considered for Form work) Cum 113.00 8,406.45 949,928.85

B12 Providing and laying in position Reinforced cement concrete for all Super structures of building , Road works, Water works, Irrigation works & super structure works of bridges upto 3.50 m height. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticisers laid in layers, well compacted using needle vibrators. The cost includes all lead & lifts, cost of all materials, quality confirming to the requirements of relevant IS codes , labour, Usage charges of machinery, curing and all other appurtenances required to complete the work as per technical specifications. M25 Design (1:1.5:3) Mix Using 20 mm nominal size graded crushed coarse aggregates - For Lintels and Roof beams ( 60% considered for Form work) Cum 35.00 10,774.40 377,104.00

B13 Providing and laying in position Reinforced cement concrete for all Super structures of building , Road works, Water works, Irrigation works & super structure works of bridges upto 3.50 m height. The granite/ trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticisers laid in layers, well compacted using needle vibrators. The cost includes all lead & lifts, cost of all materials, quality confirming to the requirements of relevant IS codes , labour, Usage charges of machinery, curing and all other appurtenances required to complete the work as per technical specifications.M25 Design Mix Using 20 mm nominal size graded crushed coarse aggregates ( 45% considered for Form work for chejja,canopy,porch) Cum 5.00 9,764.30 48,821.50

B14 Providing and laying in position Reinforced cement concrete for all Super structures of building , Road works, Water works, Irrigation works & super structure works of bridges upto 3.50 m height. The granite/ trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticisers laid in layers, well compacted using needle vibrators. The cost includes all lead & lifts, cost of all materials, quality confirming to the requirements of relevant IS codes , labour, Usage charges of machinery, curing and all other appurtenances required to complete the work as per technical specifications.M25 Design Mix Using 20 mm nominal size graded crushed coarse aggregates ( 50% considered for Form work for Roof slab) Cum 42.00 10,101.00 424,242.00

B15 Providing and laying in position plain cement concrete for levelling course for all works in foundation. The granite/ trap/ basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed, laid in layers not exceeding 150 mm thickness, well compacted using plate vibrators, including all lead & lifts, cost of all materials of quality, labour, Usage charges of machineries, curing, and all the other appurtenances required to complete the work as per technical specifications. Mix 1:2:4 (M15) Using 20 mm nominal size graded crushed coarse aggregates(For coping ,Sills and floor bed,screeding concrete) Cum 34.00 6,166.00 209,644.00

B16 Supplying, fitting and placing TMT FE 550 / 550D Steel Reinforcement including cost of all materials, machinery, labour, cleaning, straightening, cutting, bending, hooking, laping/welding joints, tying with binding wire / soft annealed steel wire and other ancilary operations complete as per drawing and technical specification. For Buildings Kgs 13000.00 80.19 1,042,470.00

B17 Supplying, fitting and placing TMT FE 550 / 550D Steel Reinforcement including cost of all materials, machinery, labour, cleaning, straightening, cutting, bending, hooking, laping/welding joints, tying with binding wire / soft annealed steel wire and other ancilary operations complete as per drawing and technical specification. For all other type of structures Kgs 10000.00 69.75 697,500.00

B18 Providing and fixing Structural Steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting,hoisting, fixing in position and applying a priming coat of approved steel primer all complete including cost of materials, labour, usage charges of machinery complete as per specifications and as per directions of the Engineer-in-Charge Kgs 5000.00 108.00 540,000.00

B19 Construction of dry lean cement concrete Sub- base over a prepared sub-grade with coarse and fine aggregate conforming to IS: 383, the size of coarse aggregate not exceeding 25 mm,aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per table 600-1, cement content not to be less than 150 kg/ m3, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant, transported to site, laid with a paver with electronic sensor, compacting with 8-10 t vibratory roller, finishing and curing. For Road bed Cum 103.00 4,876.00 502,228.00

B20 Providing and laying in position Cement Concrete for all Super structures of building , Road works, Water works, Irrigation works & super structure works of bridges upto 3.50 m height. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticisers laid in layers, well compacted using needle vibrators. The cost includes all lead & lifts, cost of all materials, quality confirming to the requirements of relevant IS codes , labour, Usage charges of machinery, curing and all other appurtenances required to complete the work as per technical specifications. M 40 Design Mix Using 20 mm nominal size graded crushed coarse aggregates-For RCC Road (5% considered for form work) Cum 81.00 7,756.35 628,264.35

B21 Providing and filling joint sealing compound as per drawings and technical specifications with coarse sand and 6 per cent bitumen by weight m 180.00 48.00 8,640.00

B22 Constructing brick masonry chamber of internal dimension 600x600mm and depth of 600mm (inner dimensions) with modular bricks of CD 75 in cement mortar 1:6, bed concrete 150mm thick with 1:3:6, plastering 12 mm thick with cement mortar 1:4, CC 1:2:4 coping 75mm thk for fixing CI cover & frame etc. including the cost of CI frame and cover. Nos. 4.00 5,454.00 21,816.00

B23 Providing and fixing SFRC frame and cover conforming to IS 12592 (part-I)-1988 and IS 12592 (part-II)- 1991 with latest amendment, including cutting slabs to the required size for the opening and fixing the cover in C.C. 1:2:4 and C.M. 1:3 plastering 20 mm thick to all exposed faces, curing for 10 days with all lead and lift with appurtenances. complete Set 5.00 1,914.00 9,570.00

B24 Providing Size Stone masonry with hard stone in foundation & plinth with Cement mortar 1:6 (1 cement : 6 coarse sand) Cum 55.00 6,364.00 350,020.00

B25 Providing Brick work with common burnt clay Non Modular bricks of class designation 3.5 in superstructure above plinth level in all shapes and sizes in Cement mortar 1:6 (1 cement : 6 coarse sand) including cost of all materials, labour, scaffolding and usage charges of machinery & other incidental charges complete as per the direction of engineer incharge of work. Cum 128.00 7,948.00 1,017,344.00

B26 Providing 18 mm cement plaster in two coats under layer 12 mm thick cement plaster with cement mortar 1:5 (1 cement : 5 coarse sand) finished with a top layer 6 mm thick cement plaster with cement mortar 1:6 (1 cement : 6 fine sand) to brick masonry including rounding off corners wherever required smooth rendering, providing and removing scaffolding, including cost of materials, labour, curing complete as per specifications and as per directions of Engineer-in-charge.(Outside plastering) Sqm 732.00 369.00 270,108.00

B27 Providing 12 mm cement plaster with cement mortar 1:4 (1 cement:4 fine sand) to brick masonry including rounding off corners wherever required smooth rendering, providing and removing scaffolding, including cost of materials, labour, curing complete as per specifications and as per directions of Engineer-in-charge (Ceiling plastering) Sqm 309.00 253.00 78,177.00

B28 Providing 15 cement plaster on rough side of single or half with cement mortor 1:4 to brick masonary including rounding off corners wherever required smooth rendering, providing and removing scaffolding including codt of material,labo,curing complete as per specificatoins and as per direction of engineer in charge(Inside plastering) Sqm 1022.00 293.00 299,446.00

B29 Providing Flush/ Ruled pointing: Pointing on stone work with cement mortar 1:3 (1 cement : 3 fine sand) after raking joints to depth nicely lining, including cost of materials, labour, curing as per specifications and as per directions of Engineer-in-charge . Sqm 154.00 255.00 39,270.00

B30 Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :Two coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture after thoroughly brooming the surface to remove all dirt, dust, mortar drops and foreign matter including preparing the surface even and sand paper smooth, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge. Sqm 250.00 167.00 41,750.00

B31 Providing and Applying CFTRI approved two component flexible polymer modified acrylic cementitious waterproofing coating with a mix ratio of (5 Liquid :7 Powder) to the RCC surface like Roof, bathroom, toilet, balcony & utility area applied @ 2.2kg/m2 in 2 coats to achieve 1.2mm DFT, having Elongation at break >120% as per ASTM D 412, Tensile strength >1N/mm2 as per ASTM D 412, Adhesion strength: 0.80N/mm2 as per ASTM D 4541, crack bridging upto 2mm as per ASTM C 836. The finished cost to include surface preparation, making coving of 50 mm X 50mm at all right angles of wall Junction with Polymer Repair Mortar and lay 45 gsm glass fibre mesh over the angle fillet when the first coat in still wet, treatment of cracks completely as per specification. Sqm 223.00 525.00 117,075.00

B32 Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.** Polished Granite stone slab Black, Cherry Red, Brown, Cat Eye, River Pink or equivalent. Sqm 335.00 2,852.00 955,420.00

B33 Providing edge moulding to 18mm thick Granite stone counters, vanities etc including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-charge. m 70.00 328.00 22,960.00

B34 Providing and fixing 10 mm thick acid and/or alkali resistant tiles of approved make and colour using acid and/or alkali resisting mortar bedding for Bathrooms: Toilet: Chemically exposed areas and joints filled with acid and/or alkali resisting cement as per IS : 4457, complete as per the direc tion of Engineer-in- Charge. In flooring on a bed of 10 mm thick mortar 1:4 (1 acid proof cement : 4 coarse sand) with Acid and alkali resistant tile For battery room floor Sqm 19.00 1,244.00 23,636.00

B35 Providing and fixing 10 mm thick acid and/or alkali resistant tiles of approved make and colour using acid and/or alkali resisting mortar bedding for Bathrooms: Toilet: Chemically exposed areas and joints filled with acid and/or alkali resisting cement as per IS : 4457, complete as per the direction of Engineer-in- Charge. In dado/skirting on 12 mm thick mortar 1:4 (1 acid proof cement : 4 coarse sand) with Acid and alkali resistant tile For battery room wall Sqm 37.00 1,259.00 46,583.00

B36 Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/m2 including pointing the joints with white cement and matching pigment etc., complete. Sqm 24.00 1,072.00 25,728.00

B37 Providing skirting, dadooing, rises of steps with colour glazed tiles 6mm thick on 10mm thick cement plaster 1:3 and jointed with white cement slurry over existing rough plaster surface using glazed tiles of approved make and size including cost of materials, labour, complete as per specifications.() Sqm 97.00 1,446.00 140,262.00

B38 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete as per specifications and as per directions of Engineer incharge. Sqm 1331.00 100.00 133,100.00

B39 Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound) content. With water thinnable cement primer on wall surface having VOC content less than 50 g/L as per specifications and as per directions of Engineer in charge Sqm 1331.00 53.00 70,543.00

B40 Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 g/L of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. Two coats as per specifications and as per directions of Engineer in charge Sqm 1331.00 110.00 146,410.00

B41 Finishing walls with Acrylic Smooth exterior paint of required shade :New work (Two coat applied @ 1.67L/10 m² over and including priming coat ofexterior primer applied @ 2.20 kg/10 m²) with paint of approved quality to give an even shade, after thoroughly brooming the surface to remove all dirt, dust, mortar drops and foreign matter including preparing the surface even and sand paper smooth, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge. Sqm 732.00 174.00 127,368.00

B42 Supplying PVC ringtite pipes conforming to IS 4985:2000 with latest amendments and conveying to worksite, rolling and lowering into trenches, laying true to line and level and perfect linking at joints, testing and commissioning, including loading unloading at both destinations and cuts of pipes wherever necessary including jointing of PVC pipes and specials (excluding cost of specials) with jointing of approved type, with all labour with all lead & lift including encasing the pipe alround to a depth of not less than 15 cms. with soft gravel or selected earth available from the excavation etc. complete and giving necessary hydraulic test to the required pressure as per ISS (Contractor will make his own arrangements for procuring water for testing) etc. for:PVC pipes 75mm dia., 6 kg/sqcm & class 3 Rmtr 60.00 220.00 13,200.00

B43 Supplying PVC ringtite pipes conforming to IS 4985:2000 with latest amendments and conveying to worksite, rolling and lowering into trenches, laying true to line and level and perfect linking at joints, testing and commissioning, including loading unloading at both destinations and cuts of pipes wherever necessary including jointing of PVC pipes and specials (excluding cost of specials) with jointing of approved type, with all labour with all lead & lift including encasing the pipe alround to a depth of not less than 15 cms. with soft gravel or selected earth available from the excavation etc. complete and giving necessary hydraulic test to the required pressure as per ISS (Contractor will make his own arrangements for procuring water for testing) etc. for:PVC pipes 110mm dia., 6 kg/sqcm & class 3 Rmtr 80.00 411.00 32,880.00

B44 Supplying S&S RCC SPUN / VIBRATED CAST PIPES (REINFORCED) pipes NP-3 Class conforming to IS:458-1988 with latest amentments using ordinary portland cement, for sanitary works and conveying to work site, rolling and lowering into trenches, laying true to line and level including loading and unloading at both destinations and jointing of pipes and specials, perfect linking of joints with jack to correct position including cost of jointing materials, i.e, rubber rings conforming to IS: 5382 for S&S RCC pipes, with all leads and lifts as directed and giving necessary hydraulic test as per ISS to the required pressure and commissioning etc. complete. (Contractor will make his own arrangements for procuring water for testing). Before the execution of the work, the contractor shall carry out the survey. 900mm dia Rmt 15.00 4,854.00 72,810.00

B45 Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts, locking arrangement, toppers, handles, including applying a priming coat of approved steel primer including cost of materials ,labour, usage charges of machinery complete as per specifications and as per directions of the Engineer-in-Charge. complete including necessary bolts and nuts. Smtr 9.00 8,276.00 74,484.00

B46 Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid Each 2.00 5,977.00 11,954.00

B47 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps Each 4.00 3,082.00 12,328.00

B48 Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Rectangular shape 453x357 mm Each 4.00 1,018.00 4,072.00

B49 Providing and placing on terrace (at all fllor levels) polyethylene water storage tank, IS: 12701 marked, with cover and suitable locking arrangment and making necessary holes for inlet, outlet and overflow pipes but without fitting and the base support for tank). Ltrs 2000.00 9.00 18,000.00

B50 Jelly Spreading (20-25 mm) : Supplying and providing jelly in the station yard of uniform thickness of 100 mm including the cost of materials, labour charges, required tools and plants etc., complete. Work shall be carried out as per the instructions of Engineerin-charge of works as per the standard procedure Sqm 4340.00 177.30 769,482.00

B51 Providing & fixing of 3-track x 2-panel sliding windows made out of multi chambered UPVC(Matching to RAL-9016) sections and with minimum TiO2(Titanium Dioxide) at 6PHR with TPE(Thermo Plastic Elastomer) and lead free, gaskets -grey colour having isolated drainage and reinforced with Galvanized Iron profile through-out the window frame. The outer frame having an overall size of 108mm width x 45mmheight with reinforcement of 1mm thickness and Sash with overall size of 39mm x 75mm with GI reinforcement of 2mm and mesh sash of size 37mm x 58mm. Coextruded Glazing bead for fixing of glass shall be of size 20mm x 24 mm. Windows shall be provided with 6mm plain float glass, standard hardware& Multi point locking system with touch lock. Wall thickness of frame & sash shall be of 2mm-2.5mm. Maximum possible size – 2419mm x 2200mm. (The cost is inclusive of all fixtures and separate charges for minor T&P's shall not be made) Sqm 48.00 6,734.00 323,232.00

B52 Providing & fixing of louvered ventilator made out of multi chambered UPVC(Matching to RAL-9016) sections and with minimum TiO2(Titanium Dioxide) at 6PHR with TPE(Thermo Plastic Elastomer) and lead free with gaskets -grey colour having isolated drainage and reinforced with Galvanized Iron profile through-out the ventilator frame. The frame having overall size of 39mm x 39mm with GI reinforcement of 1mm thickness. Louver clip in Aluminium (powder coated in white) will be used on the frame along with plastic parts for fixing the 4 mm pin head glass. Wall thickness of frame shall be 2mm.Maximum possible size – 1000mm x 1000mm.(The cost is inclusive of all fixtures and separate charges for minor(T&P's shall not be made) Sqm 3.00 5,719.00 17,157.00

B53 Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance ±1mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos.stainless steel hinges fixed to the frame complete as per manufacturer’sspecification and direction of Engineer- in-charge, 42x50 mm PVC Extruded section Mtr 68.00 239.00 16,252.00

B54 30 mm thick factory made Polyvinyl Chloride (PVC) door shutter made of styles and rails of a uPVC hollow section of size 60x30 mm and wall thickness 2 mm (± 0.2 mm), with inbuilt decorative moulding edging on one side. The styles and rails mitred and joint at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 25x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of ‘H’ section, a uPVC hollow section of size 100x30 mm and 2 mm (±0.2 mm) wall thickness fixed to the shutter styles by means of plastic/ galvanised M.S. ‘U’ cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness . The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer’s specification and direction of Engineer-in-charge.(CPWD SR-23) Sqm 29.00 3,253.80 94,360.20

B55 Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross- section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame (For toilets) mtr 33.00 643.00 21,219.00

B56 Providing and fixing to existing door frames Glass Fibre Reinforced Plastic(FRP) panelled door shutter of required colour and approved brand and manufacture, made with fire-retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5 mm thick FRP laminate for panels conforming to IS: 14856, including fixing to frames. (For toilets) Sqm 11.00 3,204.00 35,244.00

B57 Providing and fixing bright finished brass butt hinges with necessary screws etc. complete : 125x85x5.5 mm (heavy type) No 18.00 275.00 4,950.00

B58 Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in- charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts bolts, fasteners etc.) including cost of materials, labour, usage charges of machinery complete as per specifications and as per directions of the Engineer-in-Charge kg 300.00 565.00 169,500.00

B59 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in charge. Internal work - Exposed on wall Provding and fixing CPVC pipes 40mm dia Rmt 350.00 536.00 187,600.00

B60 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in charge. Internal work - Exposed on wall Provding and fixing CPVC pipes 25mm dia Rmt 75.00 318.00 23,850.00

B61 SUBMERSIBLE CABLE: Supply and delivery at site Brand new best make PVC insulated cable of Flat 3 core (sheathed) of nominal cross sectional area as per IS 694-1990 with ISI Mark and as per its latest amendments. 1x3x4 m2 Rmt 120.00 135.00 16,200.00

B62 PRESSURE GAUGE : Supply and delivery at site of brand new best make pressure gauge bourdon type as per IS 778/1984 with ISI Mark and as per its latest amendments - Size 100 mm Each 1.00 654.00 654.00

B63 GATE VALVE : Supply and delivery at site of brand new best make gate valve as per IS 778/1984 with ISI Mark and as per its latest amendments Size 50 mm Each 1.00 1,250.00 1,250.00

B64 NON - RETURN VALVE : Supply and delivery at site of brand new best make non-return valve as per IS 778/1984 with ISI Mark and as per its latest amendments Each 1.00 1,250.00 1,250.00

B65 POWER CAPACITOR : Supply and delivery at site best indigenous brand new power capacitor as per IS 2834/1986 with latest amendments with KPTCL authorities and erection, electrification and commissioning of the same at the location of respective pump sets KVAR 1.00 550.00 550.00

B66 MCB : Supply and delivery at site delivery of best indigenous brand new MCB (Miniature Circuit Breakers) of required capacity as per IS 88228/1978 and its latest amendments and with ISI Mark of 6/10/16/20/25/40 Amps with scalable box (Vol-5, I.no.32, P.no.162 ) Each 1.00 1,150.00 1,150.00

B67 Erection elctrification & Commissioning works of pumpsets : Labour charges for Erection, Electrification and commissioning of Pump sets, including aligning and balancing of all items including supply and erection of two pair of supporting clamps, bore well caps, cable clips and water tight gland cable protectors, bolts, nuts, valve and gauges,tools and equipments etc., involved in the job as per specifications, with necessary tests as per specifications, with testing of as per instructions of engineer incharge of work Job 1.00 6,500.00 6,500.00

B68 Ercerion of panel board & meter board Unit : Labour charges for erection of outdoor type panel board and meter board units with all necessary materials and labour, tools and equipmentsincluding providing cement concrete foundation bed etc., complete as per specification, with testing of as per instructions of engineer incharge of work. Job 1.00 1,450.00 1,450.00

B69 Main connections: Providing main connection from pole PVC insulated sheathed steel wire cable in new trench as per IS 1554/ 1988 with latest amendments with ISI mark from KPTCL pole to meter board unit. Rmt 50.00 135.00 6,750.00

B70 Supplying heavy gauge PVC conduit pipe ……mm dia ....... mm thick confirming to IS 2509 with suitable size bends, metal/PVC junction boxes, adhesive paste etc., and running before concreting the slab. The conduit should be tied to the reinforcement rods by using binding wires and unused ways of junction boxes and pipe ends should be covered using PVC end enclosures, run with 18SWG GI fish wire wherever necessary. 25mm dia 2mm thick. Mtr 150.00 78.00 11,700.00

B71 Supplying heavy gauge PVC Conduit Pipe ….dia .......mm thick with suitable size bends, metal junction boxes adhesive paste etc., by groove cutting in the wall and fixing by bracing U or J hooks and cement plastering up to the wall surface and run with 18 SWG GI fish wire run throughout the conduit wherever necessary. 19/20mm dia 2mm thick. Mtr 100.00 68.00 6,800.00

B72 Supplying heavy gauge PVC Conduit Pipe ….dia .......mm thick with suitable size bends, metal junction boxes adhesive paste etc., by groove cutting in the wall and fixing by bracing U or J hooks and cement plastering up to the wall surface and run with 18 SWG GI fish wire run throughout the conduit wherever necessary. 25mm dia 2mm thick. Mtr 150.00 79.00 11,850.00

B73 Supplying and fixing sheet metal box made out of 18 SWG sheet metal with necessary holes for cable/conduit entry as required with one coat of primer of approved make etc. 100x75x65mm Nos 6.00 118.00 708.00

B74 Supplying and fixing sheet metal box made out of 18 SWG sheet metal with necessary holes for cable/conduit entry as required with one coat of primer of approved make etc. 135x75x65mm Mtr 5.00 139.00 695.00

B75 Supplying PVC/GI flexible conduit pipe…mm dia fixing on surface over inverted tapered wooden plugs or phill plugs or rawl plugs and clamped using heavy gauge saddles at an interval of 300mm using NF screws and on either end of the pipe terminated completely. 25mm(Page No. 2, I.No. 1.9.2) Mtr 150.00 22.00 3,300.00

B76 Supplying And Fixing Metal Fan Box with Round Hook. Nos. 15.00 117.00 1,755.00

B77 Supplying and wiring adopting loop system in existing PVC Conduit /casing capping casing capping using 2x1.5Sqmm (Phase & Neutral) & 1x1.0 sqmm (Earth wire) FRLS multi strand PVC insulated copper wire (confirming to IS-694: and latest amendments) without control switch shall be fixed on the existing plastic sheet/ gang box, the other end of the wires shall be terminated with sufficient loose length in a wood/PVC round block. complete for each outlet. Short point upto 3Mtr from tapping point to out let via switch box Point 15.00 269.00 4,035.00

B78 Supplying and wiring adopting loop system in existing PVC Conduit /casing capping casing capping using 2x1.5Sqmm (Phase & Neutral) & 1x1.0 sqmm (Earth wire) FRLS multi strand PVC insulated copper wire (confirming to IS-694: and latest amendments) without control switch shall be fixed on the existing plastic sheet/ gang box, the other end of the wires shall be terminated with sufficient loose length in a wood/PVC round block. complete for each outlet. Medium point above 3Mtr upto 6Mtr from tapping point to out let via switch box. Point 15.00 379.00 5,685.00

B79 Supplying and wiring adopting loop system in existing PVC Conduit /casing capping casing capping using 2x1.5Sqmm (Phase & Neutral) & 1x1.0 sqmm (Earth wire) FRLS multi strand PVC insulated copper wire (confirming to IS-694: and latest amendments) without control switch shall be fixed on the existing plastic sheet/ gang box, the other end of the wires shall be terminated with sufficient loose length in a wood/PVC round block. complete for each outlet. Long point above 6Mtr upto 10Mtr from tapping point to out let via switch box. Point 20.00 555.00 11,100.00

B80 Concealed Conduit System Supplying heavy gauge PVC conduit pipe ...... mm dia..........mm thick confirming to IS 2509 with suitable size bends, metal/PVC Junction boxes, adhesive paste etc., and running before concreting the slab. The conduit should be tied to the reinforcement rods by using binding wires and unused ways of junction boxes and pipe ends should be covered using PVC end enclosures, run with 18SWG GI fish wire wherever necessary 25mm dia 2mm thick Per mtr 300.00 78.00 23,400.00

B81 Supplying heavy gauge PVC conduit pipe ……mm dia ....... mm thick confirming to IS 2509 with suitable size bends, metal/PVC junction boxes, adhesive paste etc., and running before concreting the slab. The conduit should be tied to the reinforcement rods by using binding wires and unused ways of junction boxes and pipe ends should be covered using PVC end enclosures, run with 18SWG GI fish wire wherever necessary. 19/20mm dia 2mm thick. Mtr 100.00 66.00 6,600.00

B82 Wiring for lighting/power circuit using one of FRLS PVC insulated 1100V grade, multistrand copper wire with low conductor resistance single core in open or concealed system of wiring with specified IS-694:confirming to latest amendments. 1.5 mm2 Mtr 300.00 26.00 7,800.00

B83 Wiring for lighting/power circuit using one of FRLS PVC insulated 1100V grade, multistrand copper wire with low conductor resistance single core in open or concealed system of wiring with specified IS-694:confirming to latest amendments. 2.5 mm2 Mtr 600.00 42.00 25,200.00

B84 Supplying and flush mounting powder coated / galvanized metal box suitable for mounting modular switch plates. The box should be firmly flush mounted after due groove cutting in Brick/Stone/C.C wall. 1-2 way Mtr 3.00 138.00 414.00

B85 Supplying and flush mounting powder coated / galvanized metal box suitable for mounting modular switch plates. The box should be firmly flush mounted after due groove cutting in Brick/Stone/C.C wall. 4-5 way Mtr 5.00 177.00 885.00

B86 Supplying and flush mounting powder coated / galvanized metal box suitable for mounting modular switch plates. The box should be firmly flush mounted after due groove cutting in Brick/Stone/C.C wall. 6Way. Each 6.00 220.00 1,320.00

B87 Supplying and flush mounting powder coated / galvanized metal box suitable for mounting modular switch plates. The box should be firmly flush mounted after due groove cutting in Brick/Stone/C.C wall. 8Way. Each 5.00 261.00 1,305.00

B88 Supplying and flush mounting powder coated / galvanized metal box suitable for mounting modular switch plates. The box should be firmly flush mounted after due groove cutting in Brick/Stone/C.C wall 10-12 way Each 2.00 319.00 638.00

B89 Supplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required nos. of machine screws, bolts nuts etc., complete on the existing metal/PVC box 1 to 2 Module Each 3.00 137.00 411.00

B90 Supplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required nos. of machine screws, bolts nuts etc., complete on the existing metal/PVC box 4 Module each 5.00 175.00 875.00

B91 Supplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required nos. of machine screws, bolts nuts etc., complete on the existing metal/PVC box. 6 Module Each 6.00 234.00 1,404.00

B92 Supplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required nos. of machine screws, bolts nuts etc., complete on the existing metal/PVC box. PVC 8Module Each 5.00 284.00 1,420.00

B93 Supplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required nos. of machine screws, bolts nuts etc., complete on the existing metal/PVC box. 10 -12 Module. Each 2.00 344.00 688.00

B94 Supplying & fixing of Porcelain fuse channel with cut out on existing wooden/panel using necessary nuts, bolts and washers.100 A. Each 4.00 691.00 2,764.00

B95 Supplying of on load change over switches 4 poles, AC- 23A Duty, 415V, 50Hz, AC Supply. With all accessories. (SM Enclosure Sheet Metal Execution).100 A Each 2.00 8,534.00 17,068.00

B96 Supplying and fixing Moulded Case Circuit Breaker (MCCB) over the existing wood/panel board using necessary screws,bolts, nuts, necessary phase separators, handle and wiring complete. Protection of Overload and Short circuit in Thermal Magnetic Release. Micro processor release shall have Earth Fault as per IS-13947. (Icu=100% lcs). In 4P MCCB, all Poles should have protection for Short-Cicrcuit/Over Load. For Microprocessor MCCBS Facility for segregating Priority and Non-Priority loads must be available in the MCCB. MCCB shall be provided with double insulation (insulation between front cover and internal power circuits to avoid any accidental contact with live current carrying path with the front cover open). Multi-pole breakers shall be designed to break all the poles simultaneously and they shall have a single mechanism.Three Pole.100 Amps 25 kA Nos 1.00 8,487.00 8,487.00

B97 Supplying & fixing miniature circuit breakers on existing MCB distribution boards using necessary fixing materials and 'C' Type curve, indicator ON/OFF, energy cross-3 with Short circuit breaking capacity of 10K and complete wiring as required confirming to IEC 60898.6-32 A SP Nos 10.00 415.00 4,150.00

B98 Supplying & fixing miniature circuit breakers on existing MCB distribution boards using necessary fixing materials and 'C' Type curve, indicator ON/OFF, energy cross-3 with Short circuit breaking capacity of 10K and complete wiring as required confirming to IEC 60898.50-63 A SP Nos 4.00 811.00 3,244.00

B99 Supplying & fixing miniature circuit breakers on existing MCB distribution boards using necessary fixing materials and 'C' Type curve, indicator ON/OFF, energy cross-3 with Short circuit breaking capacity of 10K and complete wiring as required confirming to IEC 60898.6-32 A TPN Nos 2.00 1,717.00 3,434.00

B100 Supplying and fixing regular MCB distribution boards on wall/ood board / flush mounting using required clA, bolts, nuts etc., with provision for fixing suitable type capacity MCB's single phase/3 phase/single door with powder coated painting Made out of 14 SWG MS enclosure.II - Double Door.12 Way SP & N Nos 1.00 2,329.00 2,329.00

B101 Supplying, fixing and wiring Earth Leakage Miniature Circuit Breaker (ELMCB) 240/450V upto 300mA sensitivity on existing wood/panel board.16-25 A 2 pole Nos 5.00 4,277.00 21,385.00

B102 Supplying, fixing and wiring Earth Leakage Miniature Circuit Breaker (ELMCB) 240/450V upto 300mA sensitivity on existing wood/panel board.63 A 4 pole Nos 1.00 5,545.00 5,545.00

B103 Supplying, fixing and wiring 0 to 1500A CT operated AC analog type Ammeter without CT Nos 3.00 480.00 1,440.00

B104 Supplying, fixing and wiring 3 Phase Digital Ammeter / Voltmeter Nos 2.00 1,425.00 2,850.00

B105 Supplying, fixing and wiring Electronic Trivector Meter (ETV) 5 to 32/63 A three phase 4 wire whole current class-1 Accuracy Energy Meter. Nos 1.00 5,705.00 5,705.00

B106 Supplying and fixing of LED type panel board indicating lamp with required colour suitable for 230/440VAC. 50 Hz 12/24V D.C. Nos 3.00 515.00 1,545.00

B107 Supplying, fixing and wiring earth leakage relay with core balanced current transformer suitable for single phase 50HzAC with latest micro controller based, digital read out of percentage leakage current, programmable delay/auto/manual reset facility suitable to mounton DIN rail/ flush mounting on panel board. Each 1.00 9,255.00 9,255.00

B108 Supplying and fixing of modular switch & connected accessorieson existing modular switch plate as per IS 3854 and IS 1293. 6A One Way Switch Each 15.00 102.00 1,530.00

B109 Supplying and fixing of modular switch & connected accessorieson existing modular switch plate as per IS 3854 and IS 1293. 6A Two Way Switch Each 10.00 166.00 1,660.00

B110 Supplying and fixing of modular switch & connected accessorieson existing modular switch plate as per IS 3854 and IS 1293. 6A Three Way socket Each 10.00 171.00 1,710.00

B111 Supplying and fixing of modular switch & connected accessorieson existing modular switch plate as per IS 3854 and IS 1293. Stepped Fan Regulator Two Module Each 7.00 357.00 2,499.00

B112 Supplying and fixing of modular switch & connected accessorieson existing modular switch plate as per IS 3854 and IS 1293. 16A One Way Switch Each 5.00 180.00 900.00

B113 Supplying and fixing of modular switch & connected accessorieson existing modular switch plate as per IS 3854 and IS 1293. 6A Bell Push Each 2.00 177.00 354.00

B114 Supplying and fixing of modular switch & connected accessorieson existing modular switch plate as per IS 3854 and IS 1293. 32A DP Switch Each 8.00 326.00 2,608.00

B115 Supplying and fixing of modular switch & connected accessorieson existing modular switch plate as per IS 3854 and IS 1293. 6/16A Universal Socket Each 10.00 236.00 2,360.00

B116 Extra for supplying 4 mm thick white plastic plate andcovering for junction boxes of size ...... mm conduit using necessary machine screws. 80/90 mm. Nos 10.00 15.00 150.00

B117 Extra for supplying 4 mm thick white plastic plate andcovering for junction boxes of size ...... mm conduit using necessary machine screws.110 mm. Nos 10.00 21.00 210.00

B118 Supplying And fixing/replacing of 6/16/32A electrical accessories on existing switch board. 6A Pendant Holder. Nos 15.00 71.00 1,065.00

B119 Supplying & fixing miniature circuit breakers on existing MCB distribution boards using necessary fixing materials and 'C' Type curve, indicator ON/OFF, energy cross-3 with Short circuit breaking capacity of 10K and complete wiring as required confirming to IEC 60898. 50-63 A TPN Nos 2.00 3,088.00 6,176.00

B120 Supplying and fixing angle iron frame work fabricated out of M.S. angle iron.. and M.S. Flat......with bolts, washers etc., and painted with 2 coats of red oxide and then two coats of approved paint.40 x 40 x 6 mm Mtr 15.00 305.00 4,575.00

B121 Supplying and fixing angle iron frame work fabricated out of M.S. angle iron.. and M.S. Flat......with bolts, washers etc., and painted with 2 coats of red oxide and then two coats of approved paint.50 x 50 x 6 mm Mtr 10.00 395.00 3,950.00

B122 Fabricating supplying and mounting MS box made out ....SWG suitable for floor /wall mounting, fully weather proof with provision for better heat dissipation, provided with hinged front cover, equipped with tamper proof locking arrangements, with suitable size clA with necessary cable entry pipe with gland and box should be finished with 7tanks treatment with powder coated paint and finally finished with approved colour etc., complete.16SWG Sqcm 20000.00 0.43 8,600.00

B123 Supplying exhaust fan of 1440 RPM of 300 mm (12") size with bracket blades complete for light duty suitable to operate on 230V 50Hz, AC Supply. Nos 2.00 2,969.00 5,938.00

B124 Supplying of 1440rpm heavy duty exhaust fan with bracket blades suitable to operate on 230V 50Hz, AC Supply complete.15" Sweep (450 mm) Nos 2.00 4,446.00 8,892.00

B125 Supplying capacitor type ceiling fan complete with down rod blades, shackle, canopies etc, for operation on 230 V, 50 cycles. Single phase AC supply conforming to ISS-374- 1979 and with double ball bearing system.48" Sweep (1200 mm) Regular model Nos 7.00 2,984.00 20,888.00

B126 Supplying wall mounting fan suitable to operate at singlephase 230v AC. supply.400 mm Sweep Nos 2.00 3,212.00 6,424.00

B127 Supplying of feet -PVC Batten with integrated LED tube LED light fitting 1 x 4ft - 36/40 W W with high quality diffuser with Life of 25000 burning hours & 70% lumen maintenance with CRI greater than 80. Power Input: 220-240V@ 50/60Hz & Power factor greater than 0.9 along with CE approved. 2 years Warranty against any manufacturing defect working under standard electrical condition Nos 20.00 1,269.00 25,380.00

B128 Supplying of recess mounting non integrated type LED down light 18W luminaire comprising of pressure decast/ extruded aluminium housing, with spring loaded false ceiling clA, LED of Power/COB with CCT 6500 degree K, CRI greater than 70%. efficacy greater than 100 lumen per W, 120degree beam spread, life greater than 25000 burning hours and Compliance to IS10322/ IEC 60598, LM 79 & LM 80. The lamp compartment is enclosed with anti glare opal diffuser which enhances the lighting level. LED's are driven by HF electronic driver integrated in a separate control gear assembly., with PF greater than 0.95, power loss should less than 5% of lamp Wage, short circuit & open circuit protection to be integrated in the circuit, THD less than 20%, Life as per LM 79. The operating input voltage should be between 130 to 275 V. BIS Approved and Tested by NABL/CPRI accredited laboratory with 2 years Warranty against any manufacturing defect working under standard electrical condition. each 15.00 3,138.00 47,070.00

B129 Supplying and Fixing of........mm dia class A GI pipe bracket upto 2 ms long bent at suitable angle and fixing to this bracket 1x40/2x40 W fluorescent tube street light fitting of all capacities to GI or GI or rail or RCC pole / wall using suitable clA, bolts, and nuts and wiring using suitable capacity wires. Using 25mm dia G.I.Pipe Nos 14.00 978.00 13,692.00

B130 Fixing all types and all capacities of fluorescent /false ceiling / spot light / CFL / LED fittings indoor on the wall/ ceiling / rafters / girders using 23/0.0076" twin twisted PVC insulated wires, required Nos of round blocks and clA.On wall/ ceiling / Rafter / Girders. Nos 35.00 122.00 4,270.00

B131 Fixing a ceiling / Wall mounting fan of all capacities and all types to the existing 'S'' hook with fan regulator to the existing board together with supplying and fixing 5 A. ceiling rose, necessary length of 23 / 0.0076 inch PVC insulated twin twisted copper wire and wiring. Nos 7.00 171.00 1,197.00

B132 Extra length of GI pipe of class B 19mm dia for down rod. Mtr 7.00 197.00 1,379.00

B133 Fixing one exhaust fan after making a suitable notch in the wall and finishing with cement mortar and colouring to match the existing wall or brackets, with bolts and nuts and a 5 A, ceiling rose with sufficient length of 23 / 0.0076 inch PVC insulated twin core wire of approved make with wire mesh and wooden frame. Nos 4.00 707.00 2,828.00

B134 Supplying, fixing, wiring, earth electrode for grounding conduits, I.C. cutouts and other equipments on the meter board using 40mm dia 2.90mm thick GI pipe 2.5 mtr long buried in a pit. The pit should be filled with equal proprotion of salt and charcoal 150mm alround the pipe to complete depth. The connection from the pipe to the conduit etc, is to be established through GI wire of size as per ISI specification 7.3.3. of IS 732 using 12mm dia bolts, nuts, washers and checknuts etc., the pipe shall have 16 through holes of 12 mm dia. no 2.00 3,510.00 7,020.00

B135 Supplying fixing and wiring earth electrode for grounding of lifts, transformers, DG sets etc using 40mm dia 2.9mm thick 2.5 mtr long GI pipe with GI funnel with mesh and suitable size reducer fixed on the top of the earth electrode. The funnel should be enclosed in a CC chamber of 400x400x400mm with a cast iron cover. The earth electrode shall have staggered holes of 12mm dia and the electrode should be covered 150mm alround with alternate layers of salt and charcoal from the bottom of the CC chamber. The connection from the electrode is to be established through GI strip using GI bolts and nuts. Each 2.00 4,256.00 8,512.00

B136 GI/Copper strips for grounding connections, using necessary fixing materials as required.600x600x3mm copper plate each 6.00 7,421.00 44,526.00

B137 GI/Copper strips for grounding connections, using necessary fixing materials as required.25x3mm copper strip mtr 30.00 570.00 17,100.00

Place Designation

Name of the Company

Karnataka Power Transmission Corporation Limited

SCHEDULE - 4 ( MANDATORY SPARES )

SHEET FOR TECHNOCOMMERCIAL OPENING (UN - PRICED)

Providing additional 1X10MVA, 110/11kV Power Transformer at 110/11kV Hulikal substation in Hosanagara Taluk Shivamogga District on PTK basis. Note: 10MVA PTR and 11kV switchgear will be supplied by KPTCL for above work.

WORK INDENT NO: KPTCL/2025-26/SS/ WORK_INDENT3385

Bidders Name and Address along with GSTIN No.: To,

The Chief Engineer (Elect.), Transmission(Operations) Zone, KPTCL, Prasarana Bhavana, Third Floor, Santhepete, B.M.Road, Hassan-573201

Price Breakup for Mandatory spares as per Annexure - 4 of Section - I, General, Volume - II.

Sl. No. Item Description Unit Total Qty. Indicate whether "Own Manufactured" or "Bought out item"

Place Designation

Name of the Company

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

SCHEDULE-5 COMMERCIAL DEVIATION

SHEET FOR TECHNOCOMMERCIAL OPENING

WORK INDENT NO: KPTCL/2025-26/SS/ WORK_INDENT3385

Providing additional 1X10MVA, 110/11kV Power Transformer at 110/11kV Hulikal substation in Hosanagara Taluk Shivamogga District on PTK basis. Note: 10MVA PTR and 11kV switchgear will be supplied by KPTCL for above work.

Please fill Only in the Light Blue Couloured Cell.

Please key in the SlNo.,Section , Clause , Description as given in bid sheets and finally your Statement of Deviation/Variations.

This Sheet would be opened at the Techno-Commercial Opening. Please refer Vendor Manual attached for further details.

For any further assistance for submitting your bids please call up KPTCL Office.

We agree to provide all original Documents in support of the information provided for verification upon request. (Key in as YES in the space provided)

We understand that the electonic bid submitted by us is a valid offer in accordance with IT Act. (Key in as YES in the space provided)

We are fully aware of the electronic bid formalities and abide by the same. (Key in as YES in the space provided)

If you are not deviating from any of the clauses mentioned please key in as 'NO DEVIATION' in the space provided.

Bidder's Name & Address alongwith GSTIN no. : To

The Chief Engineer (Elect.), Transmission(Operations) Zone, KPTCL, Prasarana Bhavana, Third Floor, Santhepete, B.M.Road, Hassan-573201

I/we have read each of the Clauses mentioned in INVITATION FOR TENDERS , INSTRUCTION TO TENDERERS , CONDITIONS OF CONTRACT, SPECIAL CONDITIONS OF CONTRACT and COMMERCIAL TERMS AND CONDITIONS and all the sections of Bid documents.

The following are the commercial Deviations and Variations from and exceptions to the Specifications and documents for

Providing additional 1X10MVA, 110/11kV Power Transformer at 110/11kV Hulikal substation in Hosanagara Taluk Shivamogga District on PTK basis. Note: 10MVA PTR and 11kV switchgear will be supplied by KPTCL for above work.

These deviations and variations are exhaustive. Except these deviations, the entire work shall be performed as per your specifications and documents.

Sl. NO. SECTION CLAUSE NO. DESC. AS PER SPECIFICATION STATEMENT OF DEVIATIONS/VARIATIONS

Note : Deviations specified elsewhere in the specification will not be considered.

Place Designation

Name of the company

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

SCHEDULE-6 : TECHNICAL DEVIATION

SHEET FOR TECHNO-COMMERCIAL OPENING

WORK INDENT NO: KPTCL/2025-26/SS/ WORK_INDENT3385

Providing additional 1X10MVA, 110/11kV Power Transformer at 110/11kV Hulikal substation in Hosanagara Taluk Shivamogga District on PTK basis. Note: 10MVA PTR and 11kV switchgear will be supplied by KPTCL for above work.

Please key in the SlNo., Section , Clause , Description as given in Bid sheets and finally your Statement of Deviation/Variations.

This Sheet would be opened at the Techno-Commercial Opening.

For any further assistance for submitting your bids please call up KPTCL office. Please fill only in the blue coloured cells.

We agree to provide all original Documents in support of the information provided for verification upon request. (Key in as YES in the space provided)

We understand that the electonic bid submitted by us is a valid offer in accordance with IT Act. (Key in as YES in the space provided)

We are fully aware of the electronic bid formalities and abide by the same. (Key in as YES in the space provided)

If you are not deviating from any of the clauses mentioned please key in as 'NO DEVIATION' in the space provided.

Bidder's Name & Address alongwith GSTIN no. : TO,

The Chief Engineer (Elect.), Transmission(Operations) Zone, KPTCL, Prasarana Bhavana, Third Floor, Santhepete, B.M.Road, Hassan-573201

The following are the Technical Deviations and Variations from and exceptions to the Specifications and documents for

Providing additional 1X10MVA, 110/11kV Power Transformer at 110/11kV Hulikal substation in Hosanagara Taluk Shivamogga District on PTK basis. Note: 10MVA PTR and 11kV switchgear will be supplied by KPTCL for above work.

These deviations and variations are exhaustive.Except these deiviations and variations, the entire work shall be performed as per your specification and documents.

Sl. NO. SECTION CLAUSE NO. DESC. AS PER SPECIFICATION STATEMENT OF DEVIATIONS/VARIATIONS

Note : Deviations specified elsewhere in the specification will not be considered.

Place Designation

Name of the company

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

SCHEDULE 7(List of special tools and tackles )

SHEET FOR TECHNOCOMMERCIAL OPENING

WORK INDENT NO: KPTCL/2025-26/SS/ WORK_INDENT3385

Providing additional 1X10MVA, 110/11kV Power Transformer at 110/11kV Hulikal substation in Hosanagara Taluk Shivamogga District on PTK basis. Note: 10MVA PTR and 11kV switchgear will be supplied by KPTCL for above work.

Bidder's Name & Address alongwith GSTIN no. : TO,

The Chief Engineer (Elect.), Transmission(Operations) Zone, KPTCL, Prasarana Bhavana, Third Floor, Santhepete, B.M.Road, Hassan-573201

List of special tools and tackles the price of which is included in bid price.

Sl. No. For equipment Description of item Unit Quantity

Place Designation

Name of the Company

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

SHEET FOR TECHNOCOMMERCIAL OPENING

WORK INDENT NO: KPTCL/2025-26/SS/ WORK_INDENT3385

Providing additional 1X10MVA, 110/11kV Power Transformer at 110/11kV Hulikal substation in Hosanagara Taluk Shivamogga District on PTK basis. Note: 10MVA PTR and 11kV switchgear will be supplied by KPTCL for above work.

NOTE: 1 ) SHALL BE UPLOADED WITHOUT PRICES

Bidder's Name & Address alongwith GSTIN no. : To,

The Chief Engineer (Elect.), Transmission(Operations) Zone, KPTCL, Prasarana Bhavana, Third Floor, Santhepete, B.M.Road, Hassan-573201

We have enclosed(uploaded) with our proposal the following additional information.

Sl. No. Brief Description of information Ref. and Page No.

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

SCHEDULE - 9 (1 of 5) : QUALIFYING REQUIREMENTS

SHEET FOR TECHNOCOMMERCIAL OPENING

WORK INDENT NO: KPTCL/2025-26/SS/ WORK_INDENT3385

Providing additional 1X10MVA, 110/11kV Power Transformer at 110/11kV Hulikal substation in Hosanagara Taluk Shivamogga District on PTK basis. Note: 10MVA PTR and 11kV switchgear will be supplied by KPTCL for above work.

Please fill Only in the Light Blue Couloured Cell.

BIDDER'S NAME AND ADDRESS: TO,

The Chief Engineer (Elect.), Transmission(Operations) Zone, KPTCL, Prasarana Bhavana, Third Floor, Santhepete, B.M.Road, Hassan-573201

a) * We have uploaded bid as individual Bidder. (Key in Individual Bidder )

b) * We have uploaded bid in Consortium with the following Bidders. (Key in Consortium ) VOID

Name of Consortium Partner Scope / Participation of each Consortium Partner

(* Fill-up whichever is applicable)

1.0 GENERAL INFORMATION

The Bidder, bidding for this package are requested to complete the information in the following form.

Sl.No. Particulars Bidder details

1 Name of the Firm

2 Address of Head Office / Registered Office GST no.

5 Name of Contact person with Designation

6 Place of Incorporation/Registration

7 Year of Incorporation/Registration

8 Constitution or legal status of Tenderer [Upload copy]

9 Place of Registration [Upload copy]

10 Principal place of business

2.0 We are furnishing the following details/documents in support of Qualifying requirement for above mentioned project

Sl.No. Bidder details Indicate Yes /No

(a) Written power of attorney of the signatory on the bid to commit the bidder. In case of Consortium

1 Furnished / Not

2 Uploaded / Not

(b) Certificate of Registration of the Company. Please mention the date of incorporation of the company

1 Uploaded / Not

(c ) Valid Super Grade Electrical Contractor’s License issued by the Government of Karnataka as on the date of techno commercial Bid opening. Please mention the date of expiry of the License certificate issued by GOK/ Undertaking to this effect

1 Uploaded / Not

(d) Self declaration regarding Litigation w.r.t KPTCL contracts over the last five years (refer ITT)

1 Uploaded / Not

(e) Self declaration for ‘not being disqualified regarding non-performance in any of the Government utilities in the past five years’. (refer ITT)

1 Uploaded / Not

(f) An undertaking to source the supply of equipment/ material from KPTCL approved vendors only as per QR for Vendor registration, available in the KPTCL website ie., kptcl.karnataka.gov.in, Link Tendering & Procurement-Application for Vendor.

1 Uploaded / Not

(g) Self declaration regarding no action against the bidder have been taken by KPTCL in respect of Risk & Cost clause

1 Uploaded / Not

(h) Self declaration regarding 'Eligibility clauses in respect of restrictions on procurement from a bidder of a country which shares a land border with India as per Annexure-XVI

1 Uploaded / Not

(i) Self declaration regarding RESTRICTIONS ON SOURCING OF EQUIPMENTS/MATERIALS BY THE BIDDER FROM A VENDOR OF A COUNTRY WHICH SHARES A LAND BORDER WITH INDIA as per Annexure -XVII

1 Uploaded / Not

Section 3 : 1.3 Work performed of similar nature in the last Five years, preceding the date of Bid submissionof Bidder (Clause No: 3.2 (b) (i) & (ii) of ITT) - In respect of Sub Station portion and Transmission Lines resp.

Project Name Name & Address of the Employer Description of Work Voltage class Number of Sub-Stations/Length of the Line Contract Number Value of contract Rs. Lakh Date of issue of work order Specified period of completion Actual date of commissioning Remarks explaining reasons for delay in commisioning of work

Note : 1 . The documentary proof of fulfilling the qualifying requirements shall be uploaded along with the bid. The bidder shall upload the P.O,LOI/LOA, DWA, Work done, Performance Certificates issued by the end users not below the rank of Executive/ Divisional Engineer along with the bid.

2. The qualifying experience of the Bidder who is having qualifying experience shall be furnished in the above performa and Documentary Proof in support of above shall be uploaded in the form of certificates issued by authorized officers of concerned organisations.

3. IF this sheet is insufficient for furnishing the qualifying experience of the Bidder then similar sheets shall be seperately uploaded.

Date Designation

Place Name of the Company

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

SCHEDULE - 9 (2 of 5) : QUALIFYING REQUIREMENTS

SHEET FOR TECHNOCOMMERCIAL OPENING

Providing additional 1X10MVA, 110/11kV Power Transformer at 110/11kV Hulikal substation in Hosanagara Taluk Shivamogga District on PTK basis. Note: 10MVA PTR and 11kV switchgear will be supplied by KPTCL for above work.

WORK INDENT NO: KPTCL/2025-26/SS/ WORK_INDENT3385

BIDDER'S NAME AND ADDRESS: TO,

The Chief Engineer (Elect.), Transmission(Operations) Zone, KPTCL, Prasarana Bhavana, Third Floor, Santhepete, B.M.Road, Hassan-573201

Section 3 : 1.5 Information on works for which Tenders have been submitted and works which are yet to be completed as on the date of this Tender of a Bidder

(A) Existing commitments and on-going works:

Description of work Place & State Contract No & Date Name and Address of Employer Value of contract (Rs. Lakh) Stipulated period of cof Completion Value of works remaining to be completed ( Rs.Lakhs) (Attach Certificates from Engineers –in- Charge) Anticipated date of commissioning

Note:Attach Certificates from Engineers –in- Charge

B)Works for which Tenders already submitted

Description of work Place & State Name and Address of Employer Estimated value of works (Rs. Lakh) Stipulated period of Completion Date when decision is expected Remarks if any

i) The statements showing the value of existing commitments and on-going works as well as the stipulated period of completion remaining for each of the works listed should be countersigned by the Employer in charge, not below the rank of an Executive Engineer or equivalent.

ii) A self-declaration is to be uploaded by the bidder stating that "the information with regard to assessed available tender capacity (Works on Hand) furnished are correct”.

Place Designation

Name of the Company

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

SCHEDULE - 9 (3 of 5) : QUALIFYING REQUIREMENTS

SHEET FOR TECHNOCOMMERCIAL OPENING

Providing additional 1X10MVA, 110/11kV Power Transformer at 110/11kV Hulikal substation in Hosanagara Taluk Shivamogga District on PTK basis. Note: 10MVA PTR and 11kV switchgear will be supplied by KPTCL for above work.

WORK INDENT NO: KPTCL/2025-26/SS/ WORK_INDENT3385

BIDDER'S NAME AND ADDRESS: TO,

The Chief Engineer (Elect.), Transmission(Operations) Zone, KPTCL, Prasarana Bhavana, Third Floor, Santhepete, B.M.Road, Hassan-573201

Following is the list of major supplied subsation equipments/accessories which are type tested and designed, manufactured by us in accordance with internationally recognised standards.

Sl. No. Item rating, type and Designation Qty Customer Date of Order Date of Supply Date of Commissioning Ref. of Cusomer's certificate of successful operation enclosed Ref. of layout & Customer's certificae for successful commission

Note: Documentary Proof in support of above shall be uploaded in the form of certificates issued by authorized officers of concerned organisations.

Place Designation

Name of the Company

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

SCHEDULE - 9 (4 of 5) : QUALIFYING REQUIREMENTS

SHEET FOR TECHNOCOMMERCIAL OPENING

Providing additional 1X10MVA, 110/11kV Power Transformer at 110/11kV Hulikal substation in Hosanagara Taluk Shivamogga District on PTK basis. Note: 10MVA PTR and 11kV switchgear will be supplied by KPTCL for above work.

WORK INDENT NO: KPTCL/2025-26/SS/ WORK_INDENT3385

BIDDER'S NAME AND ADDRESS: To

The Chief Engineer (Elect.), Transmission(Operations) Zone, KPTCL, Prasarana Bhavana, Third Floor, Santhepete, B.M.Road, Hassan-573201

Section 3 : 1.7 Reports on the financial standing of the tenderer, such as Profit and Loss Statements and Auditor’s reports in the preceeding last five years, Audited Financial statements i.e Balance sheets, P&L statements, Turnover certificates duly certified by chartered Accountant as documentary evidence shall be uploaded.

SLNo. Particulars Year Lead Bidder Consortium Member

Mention Year Amount(Rs.) Mention Year Amount(Rs.)

Names of the constituent Firms VOID

1 Annual turn over for the last Five years Year(1) 2020-2021

2 Liquid Assets / Credit availability or access to evidence of assets

3 Whether Audited Balance sheets and Profit & Loss statement are enclosed for the last Five Years ? (yes/No)

4 Whether Bankers certificate enclosed for credit facilities? (Yes/No)

Place Designation

Name of the Company

Karnataka Power Transmission Corporation Limited

WORK INDENT NO: KPTCL/2025-26/SS/ WORK_INDENT3385

SCHEDULE - 9 (5 of 5) : QUALIFYING REQUIREMENTS

Providing additional 1X10MVA, 110/11kV Power Transformer at 110/11kV Hulikal substation in Hosanagara Taluk Shivamogga District on PTK basis. Note: 10MVA PTR and 11kV switchgear will be supplied by KPTCL for above work.

BIDDER'S NAME AND ADDRESS: TO,

The Chief Engineer (Elect.), Transmission(Operations) Zone, KPTCL, Prasarana Bhavana, Third Floor, Santhepete, B.M.Road, Hassan-573201

The information to be filled in by the Tenderer hereunder will be used for purposes of computing Tender capacity as provided for in Clause 3 of the Instructions to Tenderers. This information will not be incorporated in the Contract.

1.1 Constitution or legal status of Tenderer [Upload copy] aee2

Place of Registration [Upload copy] aee2

Principal place of business

Section 3: 1.2 Total value of works executed (KPTCL & NON KPTCL works) and payments received in the last five years (in Rs. Lakhs)

1.2 Total value of works executed (KPTCL & NON KPTCL works) and payments received in the last five years (in Rs. Lakhs) of Bidder Financial Year Details

KPTCL works Non KPTCL works

Total value of works in Rs. Lakh Total value of works in Rs. Lakh

Note: Attach relevant Certificate/s from Chartered Accountant.

Section 3: 1.9 Name, address, and telephone, telex, and fax numbers of the Tenderers' bankers who may provide references if contacted by the Employer.

Sl.No Name, address, and telephone, telex, and fax numbers of the Tenderers' bankers

1.12 Information on litigations in which the Tenderer is involved:

Other Party(ies) Employer Details of Dispute Amount involved Remarks showing Present Status

Name of the Company