SPECIAL REPAIRS TO POWER HOUSE NO 2, SERVANT QTRS OF RACE VIEW AND CRAVEN, PINES GUEST ROOM AND CERTAIN REVENUE WORKS AT DSSC WELLINGTON.

Amount

B/R PORTION Demolition of brick work or stone / boulder masonry, built in cement mortar, including all quoins, arches, pillars etc., but excluding ashlar facing, dressed stone work and precast concrete articles etc., and removing unserviceable debris off the premises all as specified and as directed.

Demolition of cement concrete (unreinforced) in ground floor and in pavings n.exc 15 cm thickness (below or above ground level) and removing unserviceable debris off the premises all as specified and as directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for, and removing unserviceable debris off the premises all as specified and directed.

Dismantling timber scantlings 40 Sqcm and over in section in any position, framed or unframed work etc, complete all as specified and as directed.

Dismantling timber scantlings as in fillets, rails, posts rafters, purlins etc., in framed/unframed work, n.exc 40 Sqcm in section in any position, complete all as specified and as directed.

Dismantling of wall and ceiling boards, (fibre, pulp, insulation, etc) or insulation boards /slabs /blankets, any thickness, including cover fillets complete all as specified and as directed.

Dismantling Asbestos cement (corrugated, semicorrugated, etc) sheets in roof, complete all as specified and as directed.

Taking down chowkats or frames including shutters (without taking off shutters from the frames) n.exc 1.50 Sqm each, and removing from site, complete all as specified and as directed.

Taking down chowkats or frames including shutters (without taking off shutters from the frames) exc 1.50 Sqm and n.exc 4 Sqm each, and removing from site, complete all as specified and as directed.

Excavation in trenches n.exc 1.50 m wide and n.exc 1.50m in depth in foundation and getting out in hard/dense soil all as specified and as directed.

M & L for providing plain cement concrete (1:4:8) type D-2, (using 40mm graded stone aggregate) as in foundations, filling and mass concrete complete all as specified and as directed.

Returning, filling in, including spreading leveling watering and well ramming in layers not exc 25 cm thick with excavated soil all as specified and as directed.

Removal of surplus excavated materials (soil) to a distance n.exc 50 m and depositing where directed at a level n.exc 1.50 m above the starting point all as specified and as directed.

M & L for RCC (1:2:4) (Nominal mix), type B-1 (using 20mm graded crushed stone aggregate) as in slab supported on walls, beams and columns in floors, roofs, landings, shelves etc complete all as specified and directed.

M & L for walling of random rubble un coursed ,well bonded ,bedded and solidly hearted, built in CM (1:4) including necessary bond stones and pointing the unaccessible dressed surface with same mortar as the work proceds all as specified and directed.

M & L for Brick work with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius, built in CM (1:6) all as specified and as directed.

M & L for Brick work with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius, built in CM (1:4) all as specified and as directed.

M & L for half brick thick brick wall with subclass 'B' bricks straight or curved on plan to any radius built in CM (1:4) all as specified and as directed.

Dismantling of floor hearth or wall tiling including cement mortor bedding (but not backing) and removing serviciable tiles to store and rubbish off the premises all as specified and as directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc., all as specified and as directed.

M & L for 40mm thick PCC (1:2:4) type B-1, (using 20mm graded crushed stone aggregate) as in flooring, finished even and smooth without using extra cement all as specified and as directed.

M & L for glazed ceramic coloured tiles 300 mm x 200 mm x 7 mm thick, as in vertical surfaces such as skirting, dado etc., set and jointed in neat cement slurry, pointed in white or coloured cement to match, laid over and including 10 mm thick rendering in CM (1:4) to receive tiles, complete all as specified and as directed.

M & L for non skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exc 0.09 Sqm but not exc 0.18 Sqm, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 15 mm thick screed bed in CM (1:6) all as specified and directed.

M & L for cudappah stone slab 20-25mm thick, machine cut including cutting, rubbing, polishing, moulding, rounding the exposed edges, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab, laid over and including 20mm thick screed bed in CM (1:6) all as specified and as directed.

M & L for use and waste of timber as in form work to sides and soffits of suspended slab such as roof slab, floor slab, shelves and similar works, for rough finished surfaces of concrete flat all as specified and as directed.

M & L for mild steel TMT bars 6mm to 8mm dia as in reinforcement spaces and binders etc., cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with mild Steel wire (annealed) not less than 0.9mm dia complete all as specified and as directed.

S & F for mild steel framed work as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing(Beam, tee, angle, chaneel or flat section) including distance pieces, cleats etc conforming to Fe 290 (Gde E-165) complete all as specified and directed by Engr-in-Charge.

M & L for second class hard wood decorative weather boarding, wrought, thickness 20mm to 25 mm and rebated on thick edge to give 20mm laps and fixed all as specified and directed.

M & L for 4mm thick Non asbestos fibre cement building boards fixed or laid/inserted to timber /GI /Aluminium /IMS framework with screws complete all as specified and as directed by Engr-in-Charge.

S & F for second class hard wood (Sal / Hollock) glazed and skeleton shutters 35 mm thick, open rebated and prepared to receive glass or gauge,etc., (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing gauge sizes of members of shutters as specified in SSR Part-I Section-8, clause 8.24 (a) for door shutter supplying and fitted to chowkats, complete all as specified and as directed.

S & F for 40mm thick Flush door shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides fitted to chowkats complete all as specified and as directed.

S & F solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC ' C' channel having a PVC sheet strip of 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rails and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to in stiles & rails with suitable PVC sheet beading and joinned together with solvent cement supplying & fixing in frames at site as per specification and drawing shown in SSR Part -II, complete all as specified and as directed.

S & F solid PVC door frame of size 50 mm x 47 mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supply & fixing in opening as per specification & drawing shown in SSR Part-II, complete all as specified and as directed.

S & F aluminium, anodised, barrel tower bolts of extruded section, 200mm long, complete all as specified and as directed.

S & F 300 mm size aluminium alloy anodised sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy, complete all as specified and as directed.

S & F mild steel cold rolled Butt hinges, medium weight, 100 mm long, complete all as specfied and as directed.

S & F aluminium handles, cast type, anodised of size 150 mm long, complete all as specified and as directed.

S & F galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples, complete all as specified and as directed.

S & F Steel windows hollow section (double leaf, gauge and glazed) with side hung shutters including projecting type hinges with steel handle and steel peg stay, complete with glazing bars dove tailed or welded, complete all as specified and as directed. Note :-Glass/gauge shall be measured seperately.

S & F for pressed steel frames of size 125 x 60 mm with 1.25mm thick sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc and providing one shop coat of primer and taring back side of frame, complete all as specified and as directed.

M & L for PCC (1:2:4) type B-0 (using 12.5mm graded stone aggregate) as in filling of steel chowkats or frames complete all as specified and as directed.

S & F mild steel framed work such as grills, gratings etc with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of watertanks and similar work conforming to Fe-290 Gde E 165 all as specified and directed.

S & F galvanised , corrugated mild steel sheeting 0.60mm thick with two corrugations side lap in roof, walls etc with grade of zinc coating 275 and fixed with L type or J type or cranked hook bolts all as specified and as directed.

S & F plain , galvanished, mild steel sheeting 0.60mm thick, in ridges, hip, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 all as specified and as directed.

M & L for second class hard wood clean sawn batten for MP tiles exc 5 sq cm and n.exc 15 sq cm in sectional area ,at 30 cm centres all as specified and directed by Engr-in-Charge.

M & L for second class hardwood plain fillets square, rectangular or traingular in section, clean sawn, secured with nails or brads in sectional area exc 13 Sqcm and n.exc 25 Sqcm all as specified and as directed.

M & L for roof tiles, mangalore pattern, best quality, approved design, interlocking at side joints, laid over 15mm thick by using necessary chemical and hardener and admixture of Make : Fosroc/ Dr. Fixit on RCC roof for fixing mangalore tile complete all as specified and directed by Engr-in-Charge.

M & L for Ridge or hip tiles to suit mangalore pattern of roofing tiles, bedded and jointed in lime mortar (1 :3) or cement mortar (1:6) all as specified and as directed.

M & L for 75 mm thick cement concrete (1:3:6) type C-2, (using 40mm graded stone aggregate) as in sub base/ plinth protection/ pavings, finished fair & even without using extra cement, complete all as specified and as directed.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc and removing rubbish off the premises all as specified and directed.

M & L for rendering 15mm thick in CM (1:4) mixed with WPC as per manufacturer's instruction (external surfaces of wall) on fair face of stone /brick surfaces, finished even and smooth without using extra cement all as specified and as directed. Note : WPC shall be measured and paid seperately.

M & L for rendering 10mm thick in CM (1:6) (internal surfaces of wall) on fair faces of stone /brick surfaces, finished even and smooth without using extra cement all as specified and as directed.

M & L for preparation of new plastered or unplastered surfaces of walls and applying two coats of white wash, complete all as specified and as directed.

M & L for preparation of new plastered or unplastered surfaces of walls and applying two coats of dry distemper, white or tinted, complete all as specified and as directed.

M & L for preparation of old plastered or unplastered surfaces of walls and applying one coat of dry distemper, white or tinted, complete all as specified and as directed.

M & L for preparation of new plastered or unplastered surfaces of walls and applying two coats of cement base paint (any shade) white or tinted, complete all as specified and directed.

S & F 3 mm thick sheet glass ordinary quality, and glazing with oil putty or wooden beads in squares n.exc 0.50 Sqm in each pane, complete all as specified and as directed.

S & F 3 mm thick figured glass pin head type and glazing with oil putty in squares n.exc 0.50 Sqm in each pane, complete all as specified and as directed.

M & L for prepartion of new wooden surfaces of any description not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified and as directed.

M & L for prepartion of old wooden surfaces of any description not otherwise described, over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

M & L for preparation of new steel surfaces of any description not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer, complete all as specified and directed.

S & F 18/19mm thick prelaminated particle board, exterior grade prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work or in shutters, shelves etc including 6mm thick teak wood lipping as required, complete all as specified and directed.

S & F 40mm dia cupboard knobs fixed with nut screw and washer of mild steel bright finished, complete all as specified and directed.

S & F hasp and staple (Safety type) aluminium anodised including bolt to hinge plate and fixed with screws, 100mm size, complete all as specified and directed.

S & F mild steel continuous piano hinges, bright finish or electro galvanised, width of flap when open 30mm, complete all as specified and directed.

S & F PVC coated mild steel conduit pipe 25mm bore (Drapery rod) with a pair of PVC coated MS clamps to hold drapery rod and decorative attachment at one or both ends of drapery rod, fixed to opening of door /windows, (each opening n.exc 1.50mtr, contained with a pair of clamps and a pair of side ornamental attachments) complete all as specified and as directed.

M & L for Plain cement concrete, (1:3:6) (Nominal Mix) type C-2 (using 40 mm graded crushed stone aggregate) as in foundation, filling, surface channel or drains etc, complete all as specified and as directed.

Extra labour for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred / stopped ends etc, complete all as specified and directed.

Dismantling of PVC or reinforced cement concrete or SGSW drain pipes upto 150mm bore, jointed in cement mortar and taking out of trenches, if required complete all as specified and as directed.

S & F PVC ( SWR) pipes, type 'B', 75mm bore, single socketed in any length ,laid in trenches or in floors all as specified and as directed.

S & F PVC ( SWR) pipes, type 'B', 110mm bore (OD), single socketed in any length ,laid in trenches or in floors all as specified and as directed.

S & F PVC (SWR) bends any radius 110 mm bore all as specified and as directed.

S & F PVC (SWR) bends any radius 75 mm bore all as specified and as directed.

S & F PVC (SWR) floor trap 110mm bore, plain with grating including jointing with solvent cement all as specified and as directed.

S & F PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and as directed.

Taking up/down steel tubing and connections including cleaning for refixing or removal to store 15mm / 20mm bore pipes all as specified and as directed.

S & F steel tubes, 15 mm bore, galvanised, "medium grade" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor including cutting chases for concealed work etc, complete all as specifed and as directed.

S & F steel tubes, 20 mm bore, galvanised, "medium grade" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor including cutting chases for concealed work etc, complete all as specifed and as directed.

S & F rotational moulded polyethylene water storage tank 500 Ltrs capacity, ISI marked (cylindrical vertical with closed top), three wall layer construction, hoisted and fixed in position complete all as specified in SSR Part-I, complete all as specified and directed.

S & F in repairs bib cock long body with wall flange of Make : Jaquar, Cat No :ORP 10037PM or equivalent in Hindware /Cera /Parryware /Jaquar all as specified and directed.

S & F in repairs 15mm bore Pillar tap, cast copper alloy, with capstan head, chromium plated, screwed down high pressure, with or without lettered hot/cold with long screwed shank complete all as specified and as directed.

S & F in repairs 15mm dia angular stop cock with wall flange of Make : Jaquar, Cat No: ORP 10053 PM or equivalent in Hindware /Cera /Parryware all as specified and directed.

S & F in repairs 20 mm bore stop valves, fancy type, cast copper alloy, screwed down, high pressure, screwed both ends for iron pipe or union, complete all as specified and as directed.

S & F in repair ball valves high pressure of PTMT for 20mm bore pipe with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 20mm-210gms), complete all as specified and as directed.

S & F in repairs PVC connection suitable for 15 mm pipe with PTMT nuts and washers for both ends of length 450 mm long, complete all as specified and as directed.

S & F in repairs Sink with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes coupling , including bedding in cement mortar to dwarf wall or providing cantilever brackets, PVC waste pipe and connecting union to pipe, overall size (915 mm x 460 mm), bowl size (410 mm x 330 mm x 160 mm) complete all as specified and as directed.

S & F in repairs Vitreous china squatting pan water closet, orissa pattern, of size 580 x 440 mm, white, with integral foot rests (excluding flushing cistern and flush pipe) including PVC (SWR) 'S' trap, provision of lime concrete bedding and jointing to flush pipe complete all as specified and as directed.

S & F in repairs 10 litres capacity PVC, low level, valveless, syphonic action type flushing cistern, inlet ball valve, float valve, handle and fixing arrangement, 32 mm dia PVC flushing pipe and 15 mm dia 450 mm long PVC connection with PTMT waste coupling complete all as specified and as directed.

S & F in repairs Viterous china, wash hand basin, (white) of size 550 mm x 400 mm, including PTMT waste coupling 32 mm dia with long screwed shank and fly nuts, PVC medium grade 32 mm dia waste pipe, chain and plug, porcelain stopper, with brass CP nuts and washers at both ends all as specified and as directed.

M & L for flush pointing to random rubble masonry uncoursed brought up to courses in CM (1:4) complete all as specified and as directed.

M & L for hand packing with broken stone or boulders or loose filling with aggregate of gauge 40 to 80 mm in back of walls /Back side abutment at weep holes areas etc all as specified and directed.

Labour for Extra over stone walling for Hammer dressing to faces stones and dressing of face of beds and joints as specified of random rubble walling un coursed or brought up to course with maximum depression on face straight edge held against the dressing surface not exc 40mm all as specified and directed.

M & L for cement concrete (1:2:4) type B-1 (using 20mm graded stone aggregate) as in coping, cills, steps, in lintels upto 1.5m clear span and similar other works like kerb stone, bands, plinth courses, lacing courses, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, including necessary form work, complete all as specified and directed.

M & L for pre-polished coloured chequered cement concrete tiles, machine pressed, of size 300 x 300 x 25mm thick, with grey cement and pigment, set, jointed and pointed in neat cement slurry, laid in floors, over and including 15mm thick screed bed in CM (1:6), complete all as specified and directed.

Demolition of RCC wall, slab, beam, columns of RCC water storage tank on roof at first, second and third floor, carefully without disturbing existing roof slab including removing the debris from the site to a distance exc 1.00 Km but n.exc 1.5 Km complete all as specified and directed by Engr-in-Charge. Note : If any damage occured during demolition shall be made good by the contractor free of cost.

M & L for hard core of broken stone or boulders n.exc 63 mm deposited, spread and levelled in layers n.exc 15cm thick, water and rammed to a surface complete all as specified and as directed.

Demolition of Brick tiles or terrace tile /concrete any thickness and layer on roofs laid, bedded and pointed in cement mortor and removing debris off the premises all as specified and directed.

M & L for cement concrete (1:2:4) type B-0 (using 12.5 mm graded stone aggregate) 25mm thick as padding of roofs, finished fair and even complete all as specified and as directed.

M & L for providing screed bed of 15 mm thick in CM (1:4) on concrete surface mixed with WPC as per manufacturer's instruction, finished fair and even for laying roof treatment all as specified and as directed. Note : WPC shall be measured and paid separately.

M & L for laying 3mm thick APP modified water proofing membrane mineral finish, weighing not less than 3.6 Kg/Sqm, reinforced with non woven polyster matt black finished weighing not less than 100 gm/Sqm having softening point not less than 140 degree celsius longitudinal tensile strength not less than 300 N/Sqm, side lap & end lap 15 cm over a coat of bitumen primer @ 0.20 Kg/Sqm and finished all as per manufacturer's instruction and as directed by Engr-in-Charge. Note : The work shall be carried out by authorised applicators of manufacturer's.

M & L for joint free anti -skid ceramic tiles 9 to 10 mm thick (square/ rectangular) area of each tile exc 0.18 Sqm but n.exc 0.36 Sqm, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 15 mm thick screed bed in CM (1:6) all as specified and as directed.

M & L for glazed ceramic coloured tiles in bathroom of size 300 mm x 600 mm x 8-10 mm thick, as in vertical surfaces such as skirting, dado etc., set and jointed in neat cement slurry, pointed in white or coloured cement to match, laid over and including 10 mm thick rendering in CM (1:3) to receive tiles, complete all as specified and as directed.

M & L for granite (of any type) slab 18 to 20mm thick, machine cut, including grinding, moulding, rounding the exposed edges and polishing, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone slab, laid over and including15mm thick screed bed in CM (1:4) complete all as specified and directed.

Supply only liquid water proofing compound all as specified and as directed.

M & L for use and waste of timber as in formwork to sides and soffits of floor or roof beam, beam haunchings, griders, bressummers lintels, cantilivers, shelves including supports, overhangs, etc.,also splays between floors and beams all as specified and as directed.

M & L for RCC (1:2:4) (Nominal Mix) type B-1 (using 20 mm graded stone aggregate) as in beams, cantilevers, bressummers, lintels, shelves, slab over 1.5m span complete all as specified and as directed.

M & L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specified and as directed.

As per item no 108 here-in-before, but 5mm dia and over in stirupps, spaces and binders complete all as specified and as directed.

M & L for preparation of new surface of wall with two coats of wall care putty and applying two coats of oil bound distemper over a coat of primer complete all as per manufacturer's instruction and as directed by Engr-in-Charge.

M & L for preparation of new plastered external surfaces of wall by applying two coats of acrylic emulsion exterior paint (weather coating) over one coat of primer after applying wall care putty complete all as per manufacturer's instruction and as directed by Engr-in-Charge.

M & L for providing gypsum board false ceiling 10-12mm thick fixed with standard GI frame work with GI fixing channels @ 1220mm c/c and inter spaced at 610mm c/c the main fixing channels shall be fixed through GI channels suspenders from roof @ 1200 c/c, main and inter connected channel shall be fixed through fasterners clips as per manufacturer's instructions with and including plaster of paris decorative type cornice all around at the junction of wall and ceiling etc., complete all as specified and directed.

M & L for preparing false ceiling with primer and applying one coat of smart care primer (Primer cum sealer) and applying two coats of Royal Aspira of approved colour by roller all as per manufacturer's instructions of Asian Paints Limited or equivalent in Nerolac /Berger as approved by GE complete all as specified and as directed.

S & F MS fancy type decorative draphery rod 20mm dia including side caps and single /double brackets, including end bushes complete all as specified and as directed.

S & F Rotational moulded polythene water storage tanks 1000 litres capacity, triple layer (cylinderical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I, including dismantling water tanks and removing to store all as specified and as directed.

S & F in repair health faucet of Make : Jaquar, Cat No : ALD-CHR 565 or equivalent in Hindware/ Cera / Parryware, including 1.2m long flexible tube and wall hook complete all as specified and as directed.

S & F in repair soap dish holder of Make :Jaquar, Cat No - ACN - 1131N or equivalent in Hindware/Cera/Parryware all as specified and directed.

S & F in repair towel rail 600mm long of Make: Jaquar, Cat No: ACN - 1111NM or equivalent in Hindware/Cera/Parryware all as specified and directed.

S & F in repair 5.50mm thick looking mirror of size 900 x 600mm mounted on 6mm thick plywood backing or AC sheet backing including framing with first class hard wood of size 40 x 40mm decorative type polished and fixed to wooden plugs with chromium plated brass screws and cup washers all as specified and directed.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings all as specified and as directed.

S & F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws all as specified and as directed.

S & F pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws all as specified and as directed.

S & F second class hardwood plain, solid, straight chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue pinned at joints all as specified and as directed.

S & F stainless steel wire cloth of 0.45 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or wire staple all as specified and as directed.

S&F MS work as in hold fast, bands, straps, stays, wall ties, cleats etc and similar small articles conforming to (Fe-290 Gde-165) all as specified and directed.

M & L for complete removal of existing painting from the wooden joinery and sanding /preparing the old wooden surfaces by applying two coats of synthetic enamel paint over a coat of a pink primer etc., including providing half round /bevelled edge teak wood, fillets at glazing /wire mess sectional area n exc 3 Sqcm etc, complete all as specified and as directed.

S & F steel windows with side hung shutter including friction hinges with steel handle and two Nos 100mm mild steel bolts and two peg stays on each opening shutter complete with glazing bars dove tailed or welded including a shop coat red oxide of zinc chrome primer complete all as specified and as directed.

All as per item No 127 above, but without glazing bar including flat iron stiffener and suitable size nuts, bolts but without peg stays complete all as specified and as directed.

Rough excavation n.exc 1.50m deep and getting out in any type of soil complete all as specified and as directed.

M & L for Precast cement concrete (1:3:6) type C-1 (using 20 mm graded stone aggregate) block masonry with solid blocks, exc. 10 cm in width and setting in cement mortar (1:6) complete all as specified and directed.

M & L for 75mm thick, cement concrete (1:4:8) type D-2 (using 40mm graded stone aggregate) as in sub base of flooring all as specified and as directed.

M & L for machine pressed precast concrete interlocking paver block (approved) any shape and size conforming to IS 15658-2006 of 60 mm thickness M-35 Grade , laid over and including 50mm thick (Avg) crush stone sand (M sand) cushioning complete all as specified and directed.

M & L for precast reinforced cement concrete (1:2:4) type B-1 (using 20 mm graded stone aggregate) as in cover slabs with plain fair faces inclduding setting in CM (1:4) all as specified and as directed. Note : Reinforcement shall be measured and paid seperately.

M & L for mild steel round bars 10 mm dia and over, cut to length bent to shape required including cranking, hooking ends and binding with mild steel wire annealed not less than 0.9 mm dia all as specified and as directed.

S & F PVC ( SWR) pipes, type 'B', 160mm bore (OD), single socketed in any length,laid in trenches or in floors all as specified and as directed.

M & L for PCC 1:3:6 type C2 (using 40 mm graded granite stone aggregate) in concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for pipes of 150/160 mm bore all as specified and directed

M & L for cutting into existing manholes for connnecting new drains 150 mm dia, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete (1:2:4) type B-I smooth finished ,and reforming benching as required all as specified and as directed.

Excavating in post holes (for similar holes) each n.exc 0.5 cu.m, and getting out in soft/loose soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exc 25cm, watering, and removal surplus soil to a distance n.exc 50m and making good the disturbed surface all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for including fencing etc all as specified and as directed.

S & F for MS steel work as in posts and struts in fencing including cutting tops to shape as directed notching for wire etc., flat iron fillets (for securing wire mesh etc ) similar work conforming to Fe 410-0 all as specified and as directed.

S & F mild steel screw bolts (machine made) screwed on end with hexagonal or square head at one head and to be fitted with nuts and washers 16 to 20 mm dia of neck and not exc 5 cm long all as specified and as directed.

Supply only Chain link fencing MS galvanised fencing 50 x 50mm mesh and 2.90mm dia wire all as specified and as directed.

Fixing only chain link MS galvanised fencing any size or type all as specified and directed by Engr-in-Charge.

S & F galvanised, 2 strand, steel barbed wire 2.24mm dia barbed wire with 2mm dia barbs at 100mm spacings and straining and fixing to any type of standard rails securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc., all as specified and as directed. Note : Each line wire to be measured.

S & F mild steel works as in ioist, channel, angle or tee sections, posts, rafters, purlins, trusses, connecting plates, etc., fixed independently conforming to Fe-410-W (Gde E-250) Quality-A all as specified and as directed.

Surface excavation n.exc 30 cm deep and averaging 15 cm deep and getting out in hard/ dense soil complete all as specified and as directed.

M & L for durastone tile decorative of size 300 x 300 x 10 to12mm thick, set and jointed in neat cement slurry and pointed with white or coloured cement to match the shade of the tile, laid over and including screed bed in CM (1:4), 15mm thick, complete all as specified and as directed.

M & L for preparation of new mangalore pattern tile surfaces and applying two coats of anti fungal paint (weather coating) on external tiles over a coat of primer complete all as per manufacturer's instruction and as directed by Engr-in-Charge.

M & L for complete removal of existing treatment from external wall and applying two coats of acrylic emulsion exterior paint 1st quality Apex Ultima Protek of Asian Paints or equivalent (weather coating) over one coat of primer complete all as per manufacturer's instruction and as directed by Engr-in-Charge.

S & F mild steel work in tubular trusses including special shaped washer etc., complete using ERW or induction butt welded tubes confirming to IS 1161 - 1979 grade St -240 complete all as specified and as directed.

S & F 5 to 6mm thick, solid embossed pattern poly carbonate sheet, colour as approved by GE, as in roof, fixing with self tapping screw’s and joints of poly carbonate sheet shall be sealed with silicon with and including aluminum strip/ ties etc required for fixing all as per manufacturer’s instruction and directed by Engr-in-charge. Make : Laxan poly carbonate/ Harini polymers/ TUF LITE or equivalent.

M & L for double charged /ultra charged vitrified ceramic tiles, light shade, 10mm thick (square/rectangular) polished area of each tile n.exc 0.42 Sqm. in floors/skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 15 mm thick screed bed in CM (1:4) including dismantling of old tile on floor complete all as specified and as directed.

M & L for double charged /ultra charged vitrified ceramic tiles, light shade, 10mm thick (square/rectangular) polished area of each tile n.exc 0.42 Sqm. in floors/skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 10 mm thick screed bed in CM (1:3) including dismantling of old tile on floor complete all as specified and as directed.

M & L for ultra strong outdoor coloured vitrified tiles, approved design of size 400 x 400 x12mm thick of Make: Somany or equivalent, set and jointed in neat cement slurry and pointed with white or coloured cement to match the shade of the tile, laid over and including screed bed in CM (1:4), 15mm thick, complete all as specified and as directed.

M & L for ultra strong outdoor coloured vitrified tiles, approved design of size 400 x 400 x12mm thick of Make: Somany or equivalent in dados, skirting etc, set and jointed in neat cement slurry and pointed with white or coloured cement to match the shade of the tile, laid over and including screed bed in CM (1:3), 10mm thick, complete all as specified and as directed.

S & F 12 mm thick frosted with etching glass with any design and shape of (Like owl design etc) for entry window and door including removing existing glass and necessary arrangment for fixing complete all as specified and as directed by GE. Note : Melamine polising is to be done to wooden surface of door and window after fixing of glass.

S & F 12 mm thick frosted with etching glass with any design and shape of (Like owl design etc) for entry door including removing of existing wooden shutter and making arrangment of stainless steel hinges on floor and soffits for openable arangments, locking arrangments from either side , floor spring, stainless steel decorative handle on both side of shutter not less than 300mm length and 25mm dia complete all as specified and as directed by GE. Note : Melamine polising is to be done to wooden surface of door and window after fixing of glass.

S & F of hard crafted three tier ornamental fountain structure at 3 tier of 6 feet height, made up of sand stone, etc., including necessary piping of Sch 80 UPVC pipes confirming to ASTM D 1875 (for pipes and fittings) and ASTM D 2467 ( for control valves) all as shown in Drg No GE/DSSC/WD/01/ 2019, Sht 1/1 (M/s Royal Foundations & Equipments) complete all as per standard specification and as directed by GE.

S & F of 25 mm dia water level dependent foam jets made up of stainless steel 316 grade with ball joints made up of brass etc., complete all as per standard specification and as directed by GE.

S & F of 0.5 HP open submersible monoblock water-cooled horizontal pump (single phase-1440 RPM, 240 Volts, 50Hz of Make :CRI / Texmo or equivalent made up of high grade cast iron materials etc., complete all as per standard specification and as directed by GE.

S & F of warm white 18 Watts 12 volts DC LED lights made up of aluminium die casting, heat resistant, toughened glass provided with a provision for mounting cradle including cost and conveyance of materials etc., complete all as per standard specification and as directed by GE.

Dismantling of old fountain of any size and shape from existing fountain including making good to disturbed surfaces by necessary granite tile of area n.exc 1 Sqm and pointing with necessary water proof chemical for leakage proof at required at site complete all as specified and as directed by GE.

Demolition of cement concrete of any description and in any position not otherwise specially provided for removing debris off the premises complete all as specified and directed.

M & L for roof ties, Mangalore pattern, interlocking at site joints, laid dry all as specified and directed.

M & L for Ridge or hip tiles to suit mangalore pattern best quality approve design, interlocking laid over CM (1:4) 15mm thick mixed with necessary chemical hardner and admixture of make L Fosroc /Dr. Fixit of RCC roof for fixing mangalore ridge tile and jointed with same chemicals mix materials complete all as specified and directed by Engr-in-Charge.

E/M PORTION Taking down old, unserviceable aluminium point wiring (light, fan, socket or power) complete, including fixture & fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit & making good the disturbed surfaces of walls, floors, etc. complete all as directed by Engr-in-Charge.

Taking down old sub-main wiring including fixture & fittings etc., and removing unserviceable materials to store for keeping in safe custody or for taking credit & making good the disturbed surfaces of walls, floors, etc., complete all as specified and as directed.

Disconnecting /dismantling of old existing unserviceable DB's any way 240 /415 Volts with their old/unserviceable burnt MCB's all as specified and as directed.

M & L for surface point wiring with 1.5 Sq mm, FRLS PVC insulated, single core, copper conductor cable, 1100 Volt grade, multi stranded in and including PVC capping casing medium grade for one light /exhaust fan /socket outlet 5 Amps independent/call bell point controlled by one switch with and including continuous 1.5 Sqmm PVC insulated single core copper conductor cable earth continuity conductor green in colour connected to common earth and earth dolly, in and including PVC /polycarbonate rectangular block /boxes of suitable size & thickness with suitable PVC/polycarbonate cover for mounting switch, sockets etc.,complete all as specified and directed by Engr-in-Charge for the following : (a) One Light /fan/call bell point controlled by one switch 5/6 Amps.. Make : Havells/Finolex/Polycab Note :- (i) The wiring shall be done in proper color coding using red, yellow, blue for phases, black for neutral and green for earth.

(b) One switch socket out let point 5/6 Amps on same board.

(c) One switch socket out let point 5/6 Amps on independent board.

M & L for surface point wiring with two single core 2.5 Sqmm FRLS PVC Insulated, single core, copper conductor cable, 1100 volts grade, ISI marked with multi stranded in and including PVC capping casing medium grade in wall for 15/16 Amps switch-socket outlets etc., on independent board complete and including continuous 2.5 Sqmm PVC insulated single core copper conductor connected to common earth dolly, in and including PVC /polycarbonate rectangular block /boxes of suitable size & thickness with suitable PVC /polycarbonate cover for mounting switch, sockets etc.,complete all as specified and directed by Engr-in-Charge. Make : Havells/Finolex/ Polycab Note :- (i) The wiring shall be done in proper color coding using red, yellow, blue for phases, black for neutral and green for earth.

M & L for surface sub-main wiring alongwith earth wire of size (2 x 4.0) Sq. mm + (1 x 4.0) Sq. mm earth wire, ISI marked, FRLS, PVC insulated, multi stranded, copper conductor, single core cable drawn through and including PVC capping casing (medium grade) with all fittings and accessories ISI marked complete all as specified & as directed. Note : Two runs of PVC wire, one run of earth wire & one run of PVC capping casing (medium grade) shall be measured as one length. Make : Havells/Finolex/Polycab.

M & L for surface sub-main wiring alongwith earth wire of size (2 x 2.5) Sq. mm + (1 x 2.5) Sq. mm earth wire, ISI marked, FRLS, PVC insulated, multi stranded, copper conductor, single core cable drawn through and including PVC capping casing (medium grade) with all fittings and accessories ISI marked complete all as specified & as directed. Note :Two runs of PVC wire, one run of earth wire & one run of PVC capping casing (medium grade) shall be measured as one length. Make : Havells/Finolex/Polycab

S & F switch socket combination, 5 in 1, 5/6 pin, 15 Amps flush type, 240 volts, ISI marked complete all as specified and as directed. Make : Havells / L & T/ Legrand / C & S / Anchor.

S & F switch piano, flush button, single pole, one way, 5/6 Amps, 240 volts, ISI marked complete all as specified and as directed. Make : Havells / L & T/ Legrand / C & S/ Anchor.

S & F switch socket outlet 5 Pin, 5/6 Amps flush type, 240 volts, ISI marked complete all as specified and as directed. Make : Havells / L & T/ Legrand / C & S/ Anchor.

S & F socket out let 5 Amps, 240 volts, ISI marked complete all as specified and as directed. Make : Havells / L & T/ Legrand / C & S/ Anchor.

S & F bell push, flush type, 5/6 Amps complete all as specified and as directed. Make : Havells / L & T/ Legrand / C & S/ Anchor.

S & F call Bell, AC, Ding Dong type 230 Volts all as specified and as directed. Make : Anchor, Cat No: 8272 or equivalent in Legrand /C&S/Havells.

S & F ceiling rose, PVC/polycarbonate, insulated body, 3 terminals and 240 Volts, ISI marked complete all as specified & as directed. Make: Havells/CG/Anchor

S & F ultra slim elegance LED lighting fixture with extruded aluminium heat sink, 20 W, 4ft energy efficient and environmental friendly including electric connection with twin/three core cable of appropriate size in & including flexible hose from ceiling rose to fittings complete all as specified and directed by the Engr-in-Charge. Make : Havells, Cat No : LUMILINEPLUSBS 20WLED865SPCSS or equivalent of Luker/Philips.

S & F compact & sturdy LED decorative fixture (10 W) with extruded heat sink, multi purpose lighting in replacement of 2ft FTL fittings including electric connection with twin/three core cable of appropriate size complete all as specified and directed. Make : Havells, Cat No: LUMILINEPLUSBS 10WLED865SPCSS or equivalent of Luker/Philips.

S & F decorative wall mounting fixture with opal PC diffuser suitable for lamps with B22 base with all accessories internally prewired and including connecting up with and including twin/three core twisted flexible copper conductor cable of suitable size in flexible conduit all as specified and as directed. Make: Havells, Cat No: LHDL07150099 ( For Fixture) or equivalent in Philips/Luker. Make:Havells, Cat No : LHLDERHEMD8X010 (for lamps) or equivalent in Philips/Luker. Note: The cost of making good and matching to the existing surface is deemed to be included in the unit quoted rates.

S & F energy saving new generation 10 W LED, bulk head luminaire with opal diffuser with and including lamp LED 6000K including electric connection with twin/three core cable of appropriate size all as specified and as directed. Make: Havells, Cat No: RUGBYNEONFT 10WLED860SSYMTOPC or equivalent models in Philips/Luker.

S & F exhaust fan, single phase, 250mm sweep, PVC body with their all accessories fixed properly on window/ stone wall surfaces of thickness not exceeding 50cm including making proper sized exhaust hole of 250 mm dia, Louver Shutter suitable for the same exhaust fan and which shall easily be operated with exhaust air pressure. Any disturbed surfaces of wall shall be made good by cement work/plastering and matching by existing colour white/colour wash including removing of old exhaust fan and connecting with twin/three core cable of appropriate size in & including flexible hose from ceiling rose to exhaust fan complete all as specified and as directed. Make: Havells ,Code: Ventil Air-DX white or equivalent in Almonard/ Usha. Note : Old exhaust fan shall be handed over to MES stores.

S & F sheet metal enclosure for 8 way DBs double door type 240 volts, 200 Amps rated bus-bar IP-43,IK-09 with metal door, including necessary connectionall as specified and as directed. Make: Havells,Cat No: DHDNSHODDW08 or equivalent in L&T/ Legrand.

S & F sheet metal enclosure for 6 ways DBs double door type 240 volts, 200 Amps rated bus-bar IP-43,IK-09 with metal door, including necessary connection all as specified and as directed. Make: Havells,Cat No: DHDNSHODDW06 or equivalent in L&T/ Legrand.

S & F sheet metal enclosure for 4 way DBs double door type 240 volts, 200 Amps rated bus-bar IP-43, IK-09 with metal door, including necessary connection all as specified and as directed. Make: Havells, Cat No: DHDNSHODDW04 or equivalent in L&T/ Legrand.

S & F miniature circuit breakers, single pole,C-Series 240 Volts of capacity (6-32 Amps) as ordered breaking capacity 10 KA all as specified and as directed. Make: Havells,Cat No :DHMGCSPF006-032 or equvalent in L&T/ Legrand.

S & F miniature circuit breakers, SP & N, C-Series 240 Volts of capacity (6-32 Amps) as ordered breaking capacity 10 KA all as specified and as directed. Make:Havells, Cat No :DHMGCSNF006-032 or equivalent in L&T/Legrand.

M & L for earthing complete with galvanized steel earth plate electrode 600 x 600 x 6 mm thick burried directly in ground (in vertical position) earth pit not less than 2.25 mtr below normal ground level with the top edge of the earth plate not less than 1.5 mtr (B.G.L.) and connected to galvanized iron earth lead of wire 4mm dia by means of GI bolts,nuts, check nuts, and washers of galvanized iron including PCC pit & cover with suitable handle, including necessary excavation and earth work in any type of soil, 20 mm dia med grade galvanized steel tube for watering with one end fixed with cast iron funnel and wire mesh, 15mm bore medium grade galvanized steel tubing for drawing earth lead protection & common salt, charcoal in alternate layers etc. complete all as shown in Electric Plate No 3 of SSR Part 1 and testing on completion including taking down old earthing complete all as specified and as directed by Engr-in-Charge. Note : On testing after completion, if the desired earth resistance is not obtained, the earthing will be redone at no extra cost.

S & F in replacement PVC insulated flexible multicore round copper conductor cable of size 2 core 10 Sqmm including necessary end connector incl taking down unserviceable cable complete all as specified and as directed. Make: Havells, Cat No: WHMFDSKB2010 or equivalent of Finolex/Polycab.

Krishna Engineering

SRIBALAJI AND CO