8894/GWL/E8 SPECIAL REPAIR OF DRILL SQUARE AND DRILL NURSERY AT NCC OTA, GWALIOR AND PROVN OF 01 X WASHROOM WITH TOILET AT TRG AREA AT NCC OTA, GWALIOR

Amount

Demolition of concrete of any description and in position(reinforced cut to required as facilated complete all as secified and directed.

M&L for PCC Type D2 (1:4:8) using 40mm graded stone agg as in foundation filling mass concrete, complete all as specified and directed.

M & L 125 mm thick PCC (1:2:4) Type B2 using 40 mm graded stone aggregate as levelling course/mass concrete, Finishing surface of concrete toping even and smooth without using extra cement including necessary side formwork complete all as specified and directed. Note: Rate of formwork included in above mentioned item, PCC will be casted in 4mX4m Panel using MS angle or channel formwork laid in alternate panels or directed by Engineer In Charge.

Forming 12mm thick expansion joints filled with pre-formed bituminous filler and to 30mm primed and sealed with sealing compound, grade 'A' thickness 100mm complete all as specified and directed.

Demolition of brick work / stone work built in cement mortar including all quions, arches, pillars etc complete all as specified and directed

M&L for Brick work with sub class B bricks straight or curved on plan exc. 6m mean radius built in cement mortar (1:6).complete all as specified and as directed.

M&L for 15 mm thick rendering in cement mortar (1:4) on brick or concrete surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M&L PCC 1:3:6 type C-1 using 20mm graded stone aggregate as in coping, kerb, haunching etc including necessary formwork complete all as specified and directed

Excavating over areas, n exc 1.5 m deep and getting out in Soft Loose soil

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth; for foundations etc. or for shafts, well cess pits, manholes, pier holes, etc. but not exceeding 10 Sqm on plan and getting out in soft/ loose soil complete all as specified and directed.

Excavation in trenches not exceeding 1.5 m wide and exceeding 1.5 m but n. exc 3.00 m in depth; for foundations etc. or for shafts, well cess pits, manholes, pier holes, etc. but not exceeding 10 Sqm on plan and getting out in soft/ loose soil complete all as specified and directed.

M&L for reinforced cement concrete Design mix M-25 ( using 20 mm graded stone aggregate ) as in foundations, including rafts, footings, foundation beams , plinth beams , base for coloumns and mass concrete etc. complete all as specified and directed.

M&L for reinforced cement concrete Design mix M-25 ( using 20 mm graded stone aggregate ) as in coloumns , pillars , piers , posts and struts etc. complete all as specified and directed.

M&L for reinforced cement concrete Design mix M-25 ( using 20 mm graded stone aggregate ) as in beams , cantilevers bressummers , lintel over 1.5 m span etc. complete all as specified and directed.

M&L for reinforced cement concrete Design mix M-25 ( using 20 mm graded stone aggregate ) as in slab supported on walls ,beams, coumnns in floor , roof , landing complete all as specified and directed.

M&L for use and waste formwork to sides of concrete foundation , footing, base of coulmn , raft, raft beam sides and soffits of foundation and plinth beam for rough finished surfaces of concrete complete all as specified and directed

M&L use and waste formwork to soffits of suspended slabs such as roof slabs , floor slabs , landings and similar works , not exceeding 200 mm thick ( horizontal or sloping ) including slab edges for rough finished surfaces of concrete complete all as specified and directed

M&L use and waste formwork for to sides of pillar ,post ,struts ,pier column rough finished surfaces of concrete rough finished surfaces of concrete complete all as specified and directed

M&L for use and waste Formwork to sides & soffits of floor or roof beam rough finished surfaces of concrete complete all as specified and directed .

M&L for mild steel TMT bars ,10mm dia and over, cut to length bent to shape required including cranking bending spirally for hoping for coloumns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality complete all as specified and directed.

M&L for mild steel TMT bars ,6 mm to 8 mm dia over, cut to length bent to shape required including cranking bending spirally for hoping for coloumns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality complete all as specified and directed.

M&L for mild steel TMT bars 5 mm and over upto and including 10 mm dia , as in stirrups , spacers , and binders , cut to length bent to shape required including cranking bending spirally for hoping for coloumns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M&L for hard core of broken stone of gauge not exceeding 63 mm, deposited, spread & levelled in layers not exceeding 15 cm thick watered and rammed to a true surfaces complete all as specified and directed.

M&L for Moorum red bajri filling in floor or paving laid in layers n. exc. 15cm thick spread levelled and rammed including watering complete all as specified and directed.

M & L PCC (1:2:4) Type Bo using 12.5 mm graded stone aggregate as levelling course/mass concrete complete all as spd and directed.

M&L non skid ceramic Coloured tiles, 300mmx300mmx7mm thick, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match with the colour of tiles, over and including 15 mm thick screed bed or bedding layer of cement mortar 1:6 complete all as specified and directed.

M&L for digital glazed ceramic tiles, coloured tiles 300mm x 450mm x 7 to 8 mm thick on vertical faces ie. as in skirting/dado etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles fix over and including 10 mm thick backing coat in cement mortar (1:3) complete all as specified and directed.

M&L for Brick work with Fly Ash bricks straight or curved on plan exc. 6m mean radius built in cement mortar (1:6).complete all as specified and as directed.

M& L for Brick work with fly Ash bricks, straight or curved on plan to any radius, in half brick work built in cement mortar 1:4 complete all as specified and as directed.

M&L for 15 mm thick rendering in cement mortar (1:4) on brick / concrete/ stone surfaces mixed with water proofing compound finished even and smooth without using extra cement complete all as specified and as directed. Note: Water proofing compound shall be measured and paid seperatly under appropiate item of schedule 'A'

M&L for rendering 15 mm thick in CM (1:6) on fair faces of brick work or conrete surfaces/stone masonary and finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 5 mm thick in Cement Mortar (1:3) on ceiling finished even and smooth without using extra cement complete all as specified and directed.

Supply only integral water proofing compound ISI marked.

M&L for preparation of the newly plastered surfaces of ceiling & applying 3 coats of white wash on WALL surfaces complete all as specified and directed.

M&L for preparation of the newly plastered surfaces of wall & applying 3 coats of white wash on ceiling surfaces complete all as specified and directed.

M&L for preparation of newly plastered sufaces of walls & applying 2 coat of cement base paint over a coat of primer complete all as specified and directed.

S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat molded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for styles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rai ; Panelling of plain colour PVC sheet 5 mm thickness to be fitted in MS frame welded/sealed to the style and rails with suitable PVC sheet beading and joined together with solvent cement complete all as specified and directed.

S&F galvanised wire cloth, 0.48 mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanised staples complete all as specified and directed

S & F butt Hinges, medium weight, stainless steel,100 mm size complete all as specified.

S&F aluminum handles cast type, anodized of 150 mm size complete all as specified and directed.

S&F for aluminium anodised barrel tower bolt of 150mm of extruded section complete all as specified.

S & F factory made steel vetilator with top hung glazed shutters, including projecting type hinges, with steel handles and steel peg stays , complete with glazing bars, Complete all as specified and directed

S&F factory made steel ventilator with top hung glazed ventilator including projecting type hinges with steel handle and steel peg stay complete witout glazing bar , dovetailed or welded complete all as specified and directed.

S&F 3mm thick pin headed figured sheet glass quality in square n exc 0.5 sqm each pane in new glazed shutter, complete all as specified and directed.

S&F for framed work such as grills gratings, etc, with ends of bars shouldered and or riveted , or forged into spikes, framed guard bars , barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe 290 E-165 complete all as specified and directed.

M&L painting to steel surface exc 10 cm width or girth with two coats of synthetic enamelled paint over a coat of red oxide including prepration of newly or previously untreated surface complete all as specified.

S&F tubular towel rail of brass chromium plated , 20 mm dia, D type, 60 cm long betweem flanges complete all as specified and directed.

S&F for of vitreous china wash basin, white, oval type, (size as approved by Engineer In charge) Including waste coupling ,waste pipe and labour for fixing pillar tap ,pvc connection but including cutting for and pinning in ends of and including brackets complete all as specified and directed. . Note : Pillar tap and PVC connection will be measured paid separetly.

M&L for vitreous china squatting pan, orissa pattern sise 580x440mm white with integral foot rest (excluding flushing cistern) including vitreous china ‘P’ or ‘S’ traps connection to trap and to flushing pipe to complete fixed in repairs and making good to floor, complete all as specified and directed.

S&F Vitreous China Urinals, half stall type white (excluding fjushing cistern, flush pipe and waste pipe complete including providing & fixing ;lugs bedding urinal against wall in cm 1:2 securing urinal to plug with bran screw all as specified and directed.

M&L for PCC (1:3:6) type C2, (using 40mm graded stone aggregate) as in plinth protection, 75 mm thick, finishing the surface even and smooth w/o using extra cement including forming & filling expension joints 65 mm deep x 10 mm wide filled with sealing compound grade A complete all as specified and directed.

M&L for 10 mm thick rendering in CM (1:4) over roof ,surface finished even and Smooth mixed with water proofing compond complete all as speceified and as directed by engineer- in charge . Note : Water proofing compound shall be measured and paid separately under appropriate item of BOQ as "supply only "

M &L For applying water proofing treatment with the following coats :- (a) First coat of bitumen primer conforming to IS -3384 @ 0.3 Kg/sqm (b) Second Layer of APP based polymectric membrane minimum weighing 3kg /sqm and minimum 3 mm thick reinforced with polyster non woven fabric land on primed surface by torch application (c) third two coat of aluminium bituminous paint ( 200ml/sqm i.e 100 ml/sqm in each coat) over polymetric membrane complete all as specified and as directed.

Supply only Liquid water proofing compound complete.

Removing surplus soil obtained from excavation to a distance exceeding 500 metre but n. exc 1.50 Km and depositing where directed at a level not exceeding 1.5 metre above the starting paint complete all as specified and directed.

S&F Rotational moulded poly-ethylene three layes insunation puff water storage tanks (cylinderical vertical with closed top) 500 litres capacity, white in colour hoisted and fixed in position complete all as specified and directed.

S & F 15mm dia steel tubing and connection galvanized with all fittings medium grade tube in floors, walls and ceiling, concealed or fixed to wall or laid in floors complete all as specified and as directed

S & F 25mm dia steel tubing and connection galvanized with all fittings medium grade tube in floors, walls and ceiling concealed or fixed to wall or laid in floors complete all as specified and as directed

S&F bib tap, cast copper alloy, screwed down high pressure with crutch of butter fly handle fancy type CP for 15 mm bore dia. GI tubing. complete all as specified and directed.

S&F PVC valve-less, syphonic action type, flushing cistern, low level, 10 litre capacity (ISI marked) white with inlet, ball valve, float and handle including brackets complete all as specified and directed.

S&F PVC connections 15 mm dia and 450 mm long with brass nuts complete all as specified

S&F for in repairs 15mm angle cock chromium plated,cast copper alloy, with capston heads,scewed down high pressure, with or without lettered 'hot' or Cold' with long srewed shanks and flynuts, srewed for iron pipe fixed and complete all as specified .

S&F PVC (SWR) pipes, 75 mm bore, single sockets, in any length with rubber ring joints laid in floors or wall complete all as specified and directed.

S&F PVC (SWR) pipes, 110 mm bore, single sockets, in any length with rubber ring joints laid in floors or wall complete all as specified and directed.

S&F PVC (SWR) bends, 110 mm bore, any radius with access door complete all as specified and directed.

S&F PVC (SWR) bends, 75 mm bore, any radius with access door complete all as specified and directed.

M&L for PVC (SWR) vent cowl, 110 mm bore complete all as specified and directed.

S&F Ball brass valves , high pressure , with polythene float and fly nut complete & high-density plastic ball , suitable for 20 mm bore pipe, screwed for iron pipe and fixed.

M&L PVC Floor trap 75mm dia with grating including jointing with solvent complete all as specified and directed.

M&L for PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement

S&F for gun metal globe / gate value with iron wheel head screwed both ends for iron pipe of 15mm bore, complete all as specified and directed.

S&F for gun metal globe / gate value with iron wheel head screwed both ends for iron pipe of 25mm bore, complete all as specified and directed.

M&L for cement concrete (1:3:6) type C2 using 40mm graded stone aggregate in bed to drain pipe including packing under and hunching against the sides of pipes after they are laid and tested complete for pipe size of 150mm bore.

M&L for 150 mm bore Reinforced concrete pipes, class NP2, laid and jointed complete with collars

M&L for providing cement concrete (1:2:4) type B0 (using 12.5mm graded stone aggregate) in surfaces channels drains and benching including form work and finishing fair and smooth using extra cement (forming fair finished channel shall be measured and paid for separately)

M&L for precast cement concrete (1:2:4) type B1 (using 20mm graded stone agg) as in cover slabs for man holes and set in CM 1:4 including necessary from work all as specified. Note: Reinforcement and form work shall be measured paid separately)

Cutting holes in brick/stone wall ,depth of embedment portion of hold fast exc half brick wall but not exc one brick wall, built in cement mortar or cement lime mortar and making good in cement mortar 1:3 or cement concrete 1:2:4 type B1 as required complete all as specified and directed

M&L, concealed point wiring with PVC insulated and unsheathed electric cable 1100 volts grade single core FRLSH confirming to IS 694:2010 having multi stranded copper conductor of 1.5 Sqmm nominal cross sectional area (ISI marked with valid CML No) drawn in and including concealed non metallic rigid PVC conduit medium grade( ISI marked with valid CML No) not less than 20 mm dia with all fitting and fixing accessories and 1.5 Sqmm FRLSH confirming to IS 14930 (Part-I) 2001, PVC insulated unsheathed multistranded copper conductor cable as continuous earth conductor, connected to common earth dolly by providing suitable lugs with & including pressed steel sunken terminal boxes factory made for mounting switch, regulators etc with and including 2.8 mm thick plastic laminated sheet cover (white) ISI marked, fixed with brass screws and cup washers duly painted with two coats of anti corrosive paint/black bituminous paint outside and two coats of aluminium paint inside for mounting switches. sockets etc complete for the following:-

One light point controlled by one switch.

One Exhaust fan point controlled by one switch.

One 3 pin socket outlet 5 Amp controlled by one switch on independent board.

S&F switch piano, flush button single pole one way 5 Amp complete all as specified and directed.

S&F Switch socket outlet, 5 Pin, 6 Amp 2 in 1, flush type, universal complete.

S&F Ceiling rose 3 terminal/pvc/polycarbonate, isolated body.

S&F Lamp holder with metal ring, PVC/Polycarbonate type with back plate suitable for batten fittings non ISI Marked complete.

S&F LED Lamp 12 Watt with 5 Star rating complete.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300mm sweep with double bearing, blades, and frame and louvers complete all as specified and directed.

Supplying and laying of PPR/CPVC pipes of size 20 mm SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors/trench complete including taking out old pipes all as specified and directed.Note : GI/CPVC Combination Sockets & interconnection services included in the Quated rate.

Supplying and laying of GI Pipe, 'medium grade of size 20 mm',fittings on walls/ceiling or laying in floors/trench complete including taking out old pipe all as specified and directed. Note : GI/CPVC Combination Sockets & interconnection services included in the Quated rate.

M&L for Cutting existing steel tubing of any size for alteration or additions for making of connection complete all as specified and directed.

S&F PPR/CPVC BALL VALVE confirming to IS 14846/2000,ISI Mark M including dismantling of old u/s Gate valve fixed at any location of size 20 mm dia all as specified and directed.

S&F MCB DB, sheet metal enclosures double door SPN 4 way with bus bar 240 volts 2 in 1 shutter type (METAL DOOR) type with blanking plates where required and IP 43 degree protection complete all as specified and directed.

S&F, MCB SPN 40 Amps, 240 volts 'C' series 16 KA ,including connection with suitable size copper lugs complete all as specified and directed.

S&F, MCB SP 240 volts, 6 to 32 Amps, 'C' series 10 KA including connection with suitable size copper lugs. complete all as specified and directed.

Supplying, laying, testing and commissioning of XLPE insulated screened PVC bedded galvanised steel strip or wire armured electric power cable (Heavy duty ) with aluminium conductor 1100 volts grade, cross sectional area size 10 Sqmm 2 Core.

Returning, filling of excavated soil, including spreading leveling, watering and well ramming in layers, not exceeding 25cm complete all as specified and directed.

Removing of surplus soil to a distance n exc 50 m and depositing where directed at a level n exc 1.5m above the starting point complete.

Sand filling in trenches with clean dry unwashed sand free from sharp particles, gently punning around the cables complete.

Bricks, old size sub class `B' laid in trenches with width wise along the alignment of the cable as protection complete.

S&F tube 'Light' grade galvanised with all fitting laid in trenches, fixed to wall and floor of 40 mm dia for cable protection complete all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick burried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) vertically, with top edge of plate not less than 1.5 metre below normal ground level connected to galvanised earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No 3 of MES Schedule Part-I connecting to earthing test. Testing on completion with and including necessary excavation and earth work in any type soil, earth lead connected to earth test point & to main switch board etc with & including adequate quantity of charcoal dust and common salt, test point, PCC (1:3:6) type C-1 (using 20mm graded BT stone aggregate) for earth pit with 40 x 40 x 6mm mild steel angle iron frame for cover, internal surface of concrete shall be given 10mm thick plaster in CM 1:4, pre cast RCC (1:2:4) type B-1 (using 20mm graded BT stone aggregate) 40mm thick cover, reinforced with 8mm dia deformed or TMT bars 3 Nos both way with 12 mm dia round bar handle, GI medium grade watering pipe 20 mm dia with funnel and wire mesh and 15mm dia GI medium grade earth lead protection pipe including provn of earth test point made of 50 x 5 mm MS Flat in 'D' shape 500 mm legth grouted in wall complete 01 x 6 mm multistrand PVC insulated copper conductor ( Green Colour) to be provided from test point to DB through 20 mm dia concealed non metallic conduit complete all as specified and directed.

M/s Himgiri construction

M/s Ratan Lal Jain and Co.

M.S. ENGINEERS

M/s KGN Builders

Akarsha Enterprises

M/s Subhash Construction Co.

M/s. Varinder Kumar Sharma