ADDN ALT OF TOILET IN BLDG NO P 217 OF ARO T 31 AT SANGAM COMPLEX PROVN OF CAR PARKING SHELTER WITH HARD STANDING FOR OFFRS VISITORS VEH AT DEPOT AREA OF OMC PROVN OF OVERHEAD SHED WITH HARDSTANDING OF JCO MESS OF COSR SPL REPAIR TO BLDG NO T 09

Amount

Demolition of Brickwork masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles but built in Cement mortar etc complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Demolition of Concrete concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) etc complete all as specified and directed.

Demolition of Cement Concrete (reinforcment cut as required to faciliatate demolition) Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work etc complete all as specified and directed.

Taking down Chowkhat or frames not exceeding 1.5 Sqm each (Without Taking off shutters from the frames) etc complete all as specified and directed.

Taking down Chowkhat or frames exceeding 1.5 Sqm but n.exc 4 sqm each (Without taking off shutters from the frames) etc complete all as specified and directed.

Dismantling of Plain or corrugated steel sheeting, any gauge,thickness, including Nainital or similar pattern roof coverings etc complete all as specified and directed.

M&L for Non skid ceramic floor tiles of 7 to 8mm thick (Square/rectangular), area of each tile exceeding 0.11 sqm but n.exc 0.18 sqm as in floors laid over and including 15mm thick screed bed or bedding layer of mortar for laying floor finishes in CM (1:6), set and jointed in neat cement slurry and pointed in white coloured cement to match the shade of tiles etc complete all as specified and directed.

M&L for Glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of tiles , laid over and including 10mm thick CM (1:4) backing coat etc complete all as specified and directed.

M&L for Non skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles , laid over and including 15 mm thick screed bed or bedding layer in cement mortar (1:6) complete all as specified and directed.

All per Item No 10.00 here-in-above but on vertical surfaces such as skirting , dado risers to steps over and including 10 mm thick bedding layer in CM 1:4 .

Excavation in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, man holes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out of Soft/Loose soil etc complete all as specified and directed.

M&L for cement concrete in foundation (1:4:8) Type D-2 (using 40mm graded stone Aggregate) etc complete all as specified and directed.

M&L for Brickwork with subclass ‘B’ bricks(using old size burnt bricks), straight or curved on plan to any radius in half brick thick walls built in CM 1:4 etc complete all as specified and directed.

M&L for Brickwork with subclass ‘B’ bricks(using old size burnt bricks), straight or curved on plan exc 6mmean radius built in cement mortar 1:6 etc complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm etc complete all as specified and directed.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point etc complete all as specified and directed.

M&L for 40mm thick Damp proof course, (1:2:4) using 12.5mm graded stone aggregate to horizontal or vertical surfaces mixed with water proofing compound as per manufacturers instructions and applying evenly two coats of hot blown bitumen grade VG-10 @ 1.2 kg per sqm blended with clear sand @ 0.05 cum/sqm, each coat and fixing polythene film 150 micron over a coat of bitumen over full width of wall including thickness of internal and external plaster including necessary formwork etc complete all as specified and directed.

M&L for Sand filling under floors or in foundations or for laying of cables etc including watering and consolidation etc complete all as specified and directed.

M&L for Hardcore of stone of gauge n exc. 63 mm, deposited, spread and levelled in layers nexc. 15 cm thick, watered and rammed to a true surface etc complete all as specified and directed.

M&L for 100mm thick Cemen Concrete (1:4:8) Type D-2 (using 40mm graded stone aggregate) as in sub base etc complete all as specified and directed.

M&L for 25 mm thick Cement Concrete for Finishig Course Type B-1 ,(1:2:4)(using 20mm graded stone aggregate) etc complete all as specified and directed.

M&L for Rendering 15mm thick on fair faces of brick work or concrete surfaces of Cment Plaster (1:6) on internal surface etc complete all as specified and directed.

M & L rendering 15mm thick in cement mortar (1:4) on fair faces of brick or concrete work even and smooth without using extra cement etc complete all as specified and directed.

S & F for 4 mm thick of size 600x600mm HSPC (high pressure Steam Cured) pre-painted self embossed, textured designer board E-Board Classic to be fixed or laid with GI frame grid/section size 600mm x 600mm with main runner 38x24x0.9 mm thick, cross tee 28.6x24x0.9mm and wall angle 19 x19x0.9mm duly suspended with 2mm dia GI bar hangers 1200mm centre to centre both ways fixed with steel dash fasteners or from purlin from the roof with alignment clip including providing provisions for light fixtures of any size etc complete all as specified and directed.

S & F Pre-painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws complete all as specified and directed.

M & L 25mm thick second class hard wood boarding , plained one side with butt joints as in Eaves boards etc complete all as specified and directed.

M&L for applying two coats of Synthetic Enamal Paint over a coat of pink primer in New wooden surface of any description, over 10cm in width or girth of other wise described etc complete all as specified and directed.

M&L for applying two coats of synthetic enamel paint over a coat of redoxide primer in New or previously untreated steel surfaces of any description, over 10cm in width or girth of other wise described etc complete all as specified and directed.

M/L for 75 mm thick PCC 1:3:6 type C2 , using 40 mm graded agg in Plinth Protection/aprons/path laid to slope of 1:12, finished fair and even without using extra cement with and including all necessary formwork to divide tha area in panels, finishing exposed edges fair or rounding or chamfering where directed and providing 10 mm wide joints throughout thickness of plinth protection duly filled with mastic filling (one part of hot bitumen 85/25 and three part of fine sand by weight) complete all as specified and directed

S&F Factory made solid panel PVC door shutter30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification etc complete all as specified and directed.

S&F for Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification etc complete all as specified and directed.

M&L for Applying two coats of oil bound distemper on new plastered surfaces of walls including preparation of surface and priming with chalk whiting, on plastered surfaces, preparatory to distempering etc complete all as specified and directed.

M&L for Preparation of old decorated surfaces of walls by washing, rubbing down and stopping of distempered surfaces and applying two coats of oil bound distemper of approved shade/tint after complete removal of existing treatment etc complete all as specified and directed.

M&L for Preparation of new plastered surfaces and applying two coats of cement base paint of approved shade on walls including priming plastered and other surfaces with alkali resistant priming paint etc complete all as specified and directed.

S&F for 15 mm bore Bib taps, cast copper alloy screwed down, screwed for iron pipe or for brass ferrule and fixed etc complete all as specified and directed.

S&F for 15mm Bore Fancy angle Stop cock, cast copper alloy, screwed down, high pressure, screwed both ends for iron pipe or for unions and fixed etc complete all as specified and directed.

S&F Grating doom 125mm dia with waste hole of PTMT (Min wt 40 gms) etc complete all as specified and directed.

S&F for 15mm bore tubes medium grade, galvanised wih all fittings and fixed complete to walls and ceiling or laid on floors etc complete all as specified and directed.

S&F for 20 mm bore tubes medium grade, galvanised wih all fittings and fixed complete to walls and ceiling or laid on floors etc complete all as specified and directed.

S&F MS butt hings medium weight cold rolled 100mm size etc complete all as specified and directed.

S&F 150 mm long aluminium anodised Tower bolts etc complete all as specified and directed.

S&F 100mm long aluminium anodised handles etc complete all as specified and directed.

S&F for steel ventilator with top hung shutter including hinges steel peg stay, complete all as specified and directed.

S&F PVC (SWR) 110mm dia single socketed in any length with rubber ring joints laid in trenches or in floor etc complete all as specified and directed.

S&F PVC (SWR) 110mm dia Bends in any radius etc complete all as specified and directed.

S&F PVC (SWR) 110mm dia junction single T equal or un equalwith an floor etc complete all as specified and directed.

S&F of PVC (SWR) 75 mm dia vent cowl pipe as per specification etc complete all as specified and directed.

S&F 10 ltrs capacity PVC valveless syphonic action type flushing cistern low level with inlet ball valve float and dual fluash type complete all as specified complete all as specified and directed.

S&F of Vitreous China squatting pan (EWC) of pattern “long pan”, size 580 mm white with ‘P’ or ‘S” trap, front or back inlet and foot rests, any pattern (excluding flushing cistern and flush pipe) including provision of lime concrete bedding etc complete all as specified and directed.

S&F for PVC Connection pipe 15mm size with PTMT nuts of length 450 mm etc complete all as specified and directed.

S&F vitreous china wash basin, size 550 x 400mm white including brackets, and waste coupling & pipe of 32mm dia, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other and fixed etc complete all as specified and directed.

S&F soap dish chromium plated stell/stainless steel, approx size 160x160mm x 1mm thick, fixed to walls with plugs & CP brass screws complete all as specified and directed.

S&F Glass shelves, with 12mm thick desher glass incl CP brackets with brass nuts 300 mm long etc complete all as specified and directed.

S&F Mirror of size 450x600x5mm thick with aluminium frame and mounted on 6mm ply confirming to IS, with two Nos of hanging hooks fixed etc complete all as specified and directed.

S&F CP towel rail 600mm long with brackets, aluminium anodised 20mm dia etc complete all as specified and directed.

S&F CP grating 100mm dia PTMT with waste hole (Min wt 25 Gms) etc complete all as specified and directed.

S&F 15mm bore Pillar taps, cast copper alloy, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks , screwed for iron pipe and fixed etc complete all as specified and directed.

S&F PVC (SWR) Floor Trap plain with grating including jointing with solvent cement etc complete all as specified and directed.

S&F 20mm gun metal, globe or Gate valves with iron wheel head screwed both ends for iron pipe and fixed etc complete all as specified and directed.

Surface dressing n exc15 cm deep in soft/loose soil etc complete all as specified and directed.

M/L 100mm thick PCC (1:3:6) type C2 using 40mm graded stone aggregate as in floor etc complete all as specified and directed.

M&L for Forming Contraction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound grade 'A' etc complete all as specified and directed.

Excavation in post holes (or similar holes) each n.exc 0.50 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers n.exc 25 cm, watering and removing surplus soil to a distance n.exc 50 m and making good surface complete all as specified and directed.

M&L for PCC (1:2:4) type B1 using 20mm graded stone agg in plinth courses, coping, string courses, parapets, kerbs, bed plates and the like including weathering slightly rounded or chamfered angles and throating, etc complete all as specified and directed.

M&L machine pressed pre cast concrete interlocking paver block any shape & size conforming to IS15658-2006 of 80mm thickness M 40 grade using grey cement & no pigment incl 25mm thick sand cushioning etc complete all as specified and directed.

Dismantling timber scantling 40 Sqcm and over in section in any position unframed work etc complete all as specified and directed.

M&L Rendering 15 mm thick on fair faces of brick work or concrete sur-faces in cement mortar 1:4 using water proofing compound @ 3% by wt of cement for finished even and smooth (without using extra cement) (WPC will be measured and paid separately) etc complete all as specified and directed.

Supply only Integral water proofing compound etc complete all as specified and directed.

M&L for complete removal of exisitng treatment of old decorated surfaces of wall applying two coats of cement base paint on wall surface complete all as specified and directed.

M&L for preparation of old steel surfaces over 10cm width or girth and applying one coat of synthetic enamel paint all as specified and directed.

M & L for chequered cement concrete tiles of Size 25mm thick any description jointed and pointed in neat cement slurry in floors with grey cement and pigment laid over and including 15 mm thick screed bed in CM 1:6 etc complete all as specified and directed.

S&F Framed work such as grills,gratings, etc.. with ends of bars shouldered and/or riveted,or forged into spikes; framed guard bars; barred iron doors;ladders; framed balusters; walkways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 etc complete all as specified and directed.

M & L 18/19 mm thick Particle board, medium density, flat pressed, single layer type or three layer type with BWR type adhesive, fixed with screws to timber frame work in cup board shutters, partitions, shelves and similar work with teak wood beading at the edges complete all as specified and as directed.

M & L 12 mm thick Particle board, medium density, flat pressed, single layer type or three layer type with BWR type adhesive, fixed with screws to timber frame work in cup board shutters, partitions, shelves and similar work with teak wood beading at the edges complete all as specified and as directed.

S&F 40mm width Continuous (piano) hinges, mild steel, bright finish or electrogalvanised etc complete all as specified and directed.

S&F brass CP wall mixture chromium plated 15 mm bore , screwed reed down high pressure with or without lettered “hot’ or “ cold” with long screwed shanks screwed for iron pipe as in repair etc complete all as specified and directed.

S&F as in repair Health faucet of CP 15mm bore fancy type with suitable flexible pipe as per site requirement incl CP nipple with socket all as directed by Engr-in-Charge. .Make Essco Cat No-ALE-ESS-585 or equivalent in Hindware/Cera(Med range)/Prayag

S&F Sinks without drainage board made of stainless steel 1mm thick with plugs and wastes including in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160m including waste pipe & coupling 32mm in repair etc complete all as specified and directed.

S&F in repair plate rack of 750 x 600 x 210 mm of stainless steel complete all as specified and as directed.

M&L for cutting chases in brick walls, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc and cutting chases for concealed water tubing or concealed conduit wiring, etc and making good, cutting not exc 10 cm girth etc complete all as specified and directed.

S&F vitreous china wash down type water closet (pedestal pattern) including anti syphonage pipe as in repair etc complete all as specified and directed.

S&F in repairs for 15mm dia of pipe stop valves(Concealed type) ,fancy type and chromium plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes or for Unions and fixed etc complete all as specified and directed.

S/F in repairs brass chromium plated shower rose 125 mm in size with or without swivel joints any size incl fixing to steel pipe or union,etc complete all as specified and directed.

PVC (SWR) pipe 110 mm bore single socketed in any length with rubber ring joint fixed to wall including taking down of old material as in repairs etc complete all as specified and directed.

PVC (SWR) pipe 75mm bore single socketed in any length with rubber ring joint fixed to wall including taking down of old material as in repairs etc complete all as specified and directed.

PVC 75mm(SWR) dia bends any radius in repairs etc complete all as specified and directed.

Taking down shutter of any description n.exc 1 Sqm each etc complete all as specified and directed.

Taking down shutter of any description exc 1 & n.exc 2 Sqm each etc complete all as specified and directed.

M&L for 2nd class hard wood plain solid straight chowkats and frames wrought framed rebated on the solid rounded or chamfered put together with glue pined joints complete all as specified and directed.

M&L for 30 mm thick 2nd class hardwood plain framed pannelled factory made shutter (any number of panels) with panels of timber flat on both sides or of veneered particle board medium density , wood particle board with commercial face veneers , supplied and fitted to chowkats complete all as specified and directed.

M/L 35mm thick 2nd class hard wood Glazed and skelton factory made shutter, open rebated and prepared to receive glass, gauge etc. devided into squares with plain chamfered or rounded, mitred and rebated sash bars edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc. sizes of members of shutters as specified in SSR Part-I Section-8 clause 8.24(a) etc complete all as specified and directed.

S & F 4 mm (plus minus 0.50 mm) thick Sheet glass, ordinary quality and glazing with oil putty or in rubber beading with one way film in squares exceeding 0.5 Sq. M in each pane etc complete all as specified and directed.

S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples etc complete all as specified and directed.

M&L for preparation of new steel surfaces n. exc 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer etc complete all as specified and directed.

S&F Aluminium handles, cast type, anodised of 150 mm size etc complete all as specified and directed.

S&F 300 mm long, aluminium anodised sliding door bolt with hasp, stpale, bolt type, and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed etc complete all as specified and directed.

Use & waste of formwork for lintel beam flat rough finished etc complete all as specified and directed.

Form work to Chajja, troughs and similar items etc complete all as specified and directed.

Form work to edges of concrete surface exc 10cm and n.exc 20cm wide rough finished surface etc complete all as specified and directed.

MS TMT bars 10 mm dia and over cut to length, bent to shape reqd incl cranking, bending and binding with MS wire n.exc 0.90 mm dia (annealed) etc complete all as specified and directed.

M & L MS TMT bars 6 mm to 8 mm dia cut to length, bent to shape reqd incl cranking, bending and binding with MS wire n.exc 0.90 mm dia (annealed) for stirrups/binders etc complete all as specified and directed.

M & L for Reinforced Cement Concrete(Nominal mix)1:2:4 Type B-1(using 20mm graded stone aggregate) as in Beams, cantilevers, bressumers, lintels over 1.5span incl demolition of existing etc complete all as specified and directed.

All as per item No 103.00 here-in-before but as in fins, chajja etc and the like etc complete all as specified and directed.

Surface excavation n exc. (not exceeding 30 cm deep and avg 15 cm deep and getting out in any type of soil etc complete all as specified and directed.

M&L for PCC 1:2:4 type B-2, 1:2:4 using 40mm graded stone aggregate and paving 100 mm thick etc complete all as specified and directed.

S&F roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. confirming Fe-410-W(Gde-E-250) quality-B and painted one shop coat of zinc chromate primer paint (including preparation of surface) at contractors workshop before fabrication etc complete all as specified and directed.

S&F steel work in tubular trusses, post, purlins including special shaped washer etc. Complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade st-240 complete all as specified and directed by Engineer - in – Charge

S&F for Plate (plane or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment etc conforming to Fe- 410-w etc complete all as specified and directed.

S&F of mild steel screw bolts of diameter of neck 16 to 20 mm (machine made ) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut length of bolt exc 22.5 cm and n exc 30 cm long etc complete all as specified and directed.

S&F .63 mm Plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 etc complete all as specified and directed.

M&L for Pre-cast cement concrete kerb stone 1:2:4 type B-1 (using 20mm graded aggregate) required sizes incl jointed pointed in cement mortar 1:4 embeding in the ground to a depth as indicated taping earth arround kerb stone and also romovig surplus soil etc complete all as specified and directed .

Dismantling asbestos cement (Corrugated or semi corrugated) sheets in roof covering etc complete all as specified and directed.

Dismantling wall and ceiling board fibre, pulp insulation etc or insulation boards any thickness including cover fillets etc complete all as specified and directed.

Dismantling boarding of any description and fixed in any position fixed with nails or screws etc complete all as specified and directed.

Demolition of reed lathing single or double including battens and plaster or chicken wire lathing etc complete all as specified and directed.

S & F 0.71 mm dia wire netting of galvanised steel wire of size 12 mm mesh fixed with tinned tack of wire staple etc complete all as specified and directed.

M&L for rendering 12 mm thick in CM 1:6 on other side of lathing finished even and smooth without using extra cement etc complete all as specified and directed.

S&F for pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws etc complete all as specified and directed.

S&F for 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification etc complete all as specified and directed.

M&L for Solid PVC Wall Lining consisting of 5mm thick Plain or coloured with wood grains printed PVC sheet inclusive of solvent cement and fixing at site on PVC frame etc complete all as specified and directed.

S&F light shade vitrified ceramic tiles 10mm thick, area of each tile exc 0.18sqm but n.exc 0.36 Sqm each in floors laid over and including 15mm thick screed bed or bedding layer of mortar for laying floor finishes in CM (1:4) set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles etc complete all as specified and directed.

All as per Item No 122.00 here-in-above but on vertical surfaces such as skirting , dado risers to steps over and including 10 mm thick bedding layer in CM 1:4.

M & L for coloured non skid ceramic tiles 7 to 8 mm thick (square/rectangular) in section exceeding 0.06 sqm but not exceeding 0.11 sqm as in floors with 15mm thick screed bed or bedding layer of mortar for laying floor finishes in CM (1:6) set and jointed in neat cement slurry and pointed in white or coloured cemet to match etc complete all as specified and directed.

S&F anodised aluminium powder coated any colour frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and directed.

S&F for anodised aluminium powder coated any colour door shutter, aluminium section weighting 0.55 kg/m including necessary joining, cleats,glazing clips,rubbber neoprene packing, handles 2 nos in each door hinges anodised aluminium snap beading screw etc complete all as specified and directed.

S & F for aluminium Window and ventilator sliding shutters, without sash bars, aluminium sections weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc complete all as specified and directed.

S&F Sheet glass 4.8mm thick clear/sun shade colour glass, ordinary quality and glazing with oil putty in squares exceeding 0.5sqm in each pane etc complete all as specified and directed.

Hacking out old broken glass of any thicknesssize or description from wooden frames or metal frames fixed with wooden beads/ putty etc complete all as specified and directed.

S&F Sheet glass 3mm thick, ordinary quality and glazing with oil putty in squares not exceeding 0.5sqm in each pane etc complete all as specified and directed.

S&F for aluminium (extruded section) body door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed etc complete all as specified and directed.

S&F Mortice lock,vertical type Brass 2 levers, size 100 mm etc complete all as specified and directed.

S&F Aluminium anodised barrel tower bolt of extruded section and fixed 100 mm long etc complete all as specified and directed.

M&L for second class hardwood as in scantlings clean sawn timber fixed etc complete all as specified and directed.

M & L for plain fillets, square, rectangular or triangular in section clean sawn, secured with nails 2nd class hard wood exc 13 and n.exc 25 sqcm etc complete all as specified and directed.

M&L, providing Kota stone slab 20 to 25mm thick machine cut and mirror polished to size and fixed in floor and set and jointed in neat cement slurry and pointed with grey cement to match the stone floor/steps treads over 20mm thick screed bed in CM 1:4 complete all as specified and directed.

Taking up or down 15 mm GI steel tubing and connections etc complete all as specified and directed.

Taking up or down steel tubing and connections including with all fittings for 20 mm bore GI tubing etc complete all as specified and directed.

Taking down cement plaster on brick walls including raking out joints hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for preparation of new wooden fillets surfaces and wood based surfaces of any description not exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink wood primer. in tint etc complete all as specified and directed.

M&L for one coat of white wash on old plastered /decorated wall surface including preparation of old plastered or unplastered surfaces of wall including brooming down or steel wire brushing scrapping down smoke roof, mouids, moss and efflorescent salt and trading oil and greasy spots etc.

M&L 18-20mm thick granite (of any type) tiles machine cut, in skirting/ dedo laid over with 15mm thick screed bed or bedding layer of mortar for laying floor finishes in cement mortar 1:6, and jointed with grey cement cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing etc complete all as specified and directed.

M&L cement concrete type C-2 ,(1:3:6) (using 40 mm graded stone agg) as in surface channels and drains etc complete all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete using extra cement incl firms moulds etc complete all as specified and directed.

S&F 40 mm cupboards knobs fixed with nut screw and washer of brass polished etc complete all as specified and directed.

S&F magnet Catcher for cub board complete all as specified and directed.

S&F in repairs for Draperly rod /Harrison rails of CP of 20mm dia with fixing brackets , stops, rollers and rings etc complete all as specified and directed.

Taking down carefully copper/ aluminium point wiring (light, fan, socket or power) complete, including fitting & fixtures such as switches with board, ceiling roses, pendents, bell/ buzzer, bell push, lamp holders, regulators, sockets, light fittings etc., removing material from site and making good to the disturbed surfaces of walls, ceiling, floors etc. including making good the disturbed surfaces and paint touch up to match with the existing surface etc complete all as specified and as directed.

M&L for Point wiring complete with two runs of 1.5 sqmm single core PVC insulated FR-LSH cable 1100 volts grade with multi-stranded copper conductors, drawn through and including PVC double locked Casing & caping including provision of 1.5 sqmm, FR-LSH, PVC insulated copper cable as earth continuity conductor connected to common earth dolly, including PVC rectagular box for mounting switches / sockets / regulators etc. with 3 mm thick plastic laminated sheet cover of suitable size as required at site etc complete all as specified and as directed.

(a) One light/Fan pointcontrolled by one, one way switch .

(b) One 3 pin socket outlet 5 Amps on the same board with other switches.

(c) One 3 pin socket outlet 5 Amps on the switch socket combination.

All as per item No- 149.00 here-in-before but with 2.5 Sq mm for 3 pin 15 Amps socket point controlled by one switch on independent board and 2.5 Sq mm copper conductor green in colour as earth continuity conductor connected to common earth dolly complete all as specified and as directed.

M&L for Switch piano flush type single pole, one way 5A etc complete all as specified and as directed.

M&L for Socket outlet, 2 in 1, 5 pin 5A flush type etc complete all as specified and as directed.

M&L for Switch Socket combination, 2 in 1, 5 pin 6A flush type etc complete all as specified and as directed.

M&L for Switch Socket combination, 2 in 1, 5 pin 6A/16A flush typeetc complete all as specified and as directed.

M&L for stepped type electronic fan regulator 100 Watt socket size flush type on the existing phenolic laminated sheet etc complete all as specified and as directed.

M&L for ceiling rose 3 terminal PVC/Polycarbonate isolated body with PVC round/squareblock etc complete all as specified and as directed.

Material and labour for (concelaed Type) point wiring including necessary chases cutting of wall for one light/fan/call bell point with 1.5 sqmm PVC insulated (FR-LSH) PVC sheathed multistranded copper conductor cable 1100 volts grade controlled by one way switch including 1.5 sqmm PVC (FR-LSH) insulated unsheathed copper cable multistrand conductor 1100 volts grade for continuity earth wire connected to common earth dolly drawn through and including PVC conduit with all accessories and sunk modular GI box for mounting of fittings like switch, socket and fan regulator with modular inner plate and cover plate and making good the distrubed surfaces as per the existing etc complete all as specified and as directed.

(a) One light/Fan point controlled by one, one way switch .

(b) One 3 pin socket outlet 5 Amps on the same board with other switches.

(c) One 3 pin socket outlet 5 Amps on the Independent board.

All as per item No-157.00 here-in-before but with 2.5 Sq mm for 3 pin 15 Amps socket point controlled by one switch on independent board and 2.5 Sq mm copper conductor green in colour as earth continuity conductor connected to common earth dolly complete all as specified and as directed.

Taking down existing burnt aluminium/ copper sub main wiring and M&L for sub main wiring with two runs of 4 Sq mm and one run of 4 Sq mm for earth wire with multi standard copper conductors, 1100 volts grade, drawn through and including PVC double locked Casing & caping including complete all as specified and as directed. NOTE:- two runs of 4 Sq mm + one run of 4 Sq mm and one run of PVC casing & capping and its accessories of suitable size shall be measured as one unit length.

Taking down existing burnt aluminium/ copper sub main wiring and M&L for sub main wiring with two runs of 6.0 Sq mm and one run of 4.0 Sq mm for earth wire with multi standard copper conductors FRLSH quality, 1100 volts grade, drawn through and including non metalic rigid PVC conduit with all conduit accessories (including concealing and making good to the disturbed surfaces of walls, ceiling, floors etc. including making good the disturbed surfaces and paint touch up to match with the existing surface) complete all as specified and as directed. NOTE:- two runs of 4.0 Sq mm + one run of 4.0 Sq mm and one run of PVC Conduit and its accessories of suitable size shall be measured as one unit length.

Taking down existing burnt aluminium/ copper sub main wiring and M&L for sub main wiring with two runs of 6 Sq mm and one run of 6 Sq mm for earth wire with multi standard copper conductors, 1100 volts grade, drawn through and including PVC double locked Casing & caping including complete all as specified and as directed. NOTE:- two runs of 6 Sq mm + one run of 6 Sq mm and one run of PVC casing & capping and its accessories of suitable size shall be measured as one unit length .

Taking down S&F for , IP>= 20, Class-I, LED Light fitting 1 x 20 watt (4 Ft), 240 V, PF-0.9, CRI >= 80, CT>= 6500 K, Wall/ Surface mounted, intergrated type with all accessories internally prewired and incl connecting up with and incl twin/ three core twisted flexible copper conductor cable of suitable size in and incl flexible hose from ceiling rose to fitting complete all as specified and as directed.

Taking down S&F for LED Light fitting 1 x 10 watt (2 Ft), Wall/ Surface mounted, intergrated type with all accessories internally prewired and incl connecting up with and incl twin/ three core twisted flexible copper conductor cable of suitable size in and incl flexible hose from ceiling rose to fitting complete all as specified and as directed.

Taking down Supply , fixing and testing in replacement of LED Bldg Security light fitting of capacity 20 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete including 1.2 mtr GI bracket of 25mm bore light grade bent to shape and fixed on wall with metal fastners 2 Nos 10mm dia incl drilling of holes as reqd and connecting up with flexible copper cable of size 0.75 sqmm 3 core from ceiling rose to the light fitting and all as specified and directed by Engr-in-Charge.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) all as specified and directed by Engr-in-Charge.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250m etc complete all as specified and as directed.

Supply and fixing round shape 15 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size etc complete all as specified and as directed.

Supply and fixing LED luminaire 600 mm x 600 mm, 40/42 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size etc complete all as specified and as directed.

M&L for VTPN 4 way,double door 415 Volts, sheet steel, powder painted, with neutral link & earth bar etc. and fixing MCBs of various rating capacity MCB DBs incl taking down of DBs etc complete all as specified and as directed.

Supply and fixing MCB TPN 40-100 Amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning etc complete all as specified and as directed.

M&L for MCB Distribution board double door type SPN 8 way, sheet steel, powder painted, with neutral link & earth bar etc. and fixing MCBs of various rating capacity including taking down old unsv MCB DBs etc complete all as specified and as directed.

M&L for MCB Distribution board double door type SPN 4 way, sheet steel, powder painted, with neutral link & earth bar etc. and fixing MCBs of various rating capacity MCB DBs etc complete all as specified and as directed.

M&L for MCB SPN 40 Amps 'C' series, 230 volts, 50 Hz suitable for fixing in MCB DB incl taking down old unsv MCB complete all as specified and as directed.

M&L for MCB SP 6-32 Amps 'C' series, 230 volts, 50 Hz suitable for fixing in MCB DB incl taking down old unsv MCB complete all as specified and as directed.

Taking down Ceiling fan/ Exhaust Fan of any sweep carefully from its installed position, dismantling complete, cleaning all dust, applying grease for bearing, including filling cavaties with filler, after cleaning all dust, reassembling the fan and blades, hanging/ fixing the fan in its original position and testing on completion etc complete all as specified and as directed.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300mm sweep with, blades, and frame and louvers complete all as specified and directed.

Supply and fix electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc.complete all as specified and as directed.

Taking down LT UG cable/ service connection of any size and M&L for laying of LT UG cable, XLPE insulated, galvanised steel strip or wire armoured, heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area of 16 sq mm, 4 core complete all as specified and as directed. NOTE :- (i) Excavation and earth work, sand cushioning, cable protection cover, pipe etc. shall be measured and paid seperately under relevant items.

M&L for laying brick sub class 'B' old size burnt bricks for cable protection of size 230mmx115mmx75mm etc complete all as specified and as directed.

Supply & laying tubes 'light grade' galvanised, with all fittings, fixed complete to walls, poles, ceilings or laid in floors/ trenches/ road crossing for protection of cables of size 40 mm dia bore including taking out unsv GI tubing complete all as specified and as directed.

Material & Labour for earthing with galvanised steel earth plate electrode of size 60cmx60cmx6mm thick buried directly in ground (earth pit not less than 2.25m deep below the ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to the galvanised earth lead strip 32x6mm by means of bolts, nuts check nuts and washers of galvanised iron or steel as shown in electrical plate No. 3 of SSR Part-I connected to earthing test point all as specified orindicated including testing on completion including necessary excavation and earth work in soft/loose soil, returning filling, disposal of surplus soil, earth pit in PCC 1:3:6 type C-1, RCC (1:1.5:3) type A1 precast cover (54cmx54cmx5cm) duly reinforced with including 8 mm dia TMT bar @ 150mm c/c both ways, one lifting handle made of 8mm dia TMT bar, embeded in precast cover slab, funnel, 20mm dia GI medium grade watering pipe, 15mm dia GI light grade earth lead protection pipe, chorcoal and common salt in alternatee layer complete all as specified and directed by Engr-in-Charge.

M/S Lucky Builders

SHRI RAJNATH SINGH

SK SINGH

SHRI MADAN SINGH

M/S SANGITA TRADERS

MS SADHNA RAHUL

TOSHIKA SUMI

das enterprises