PROVN OF BOUNDARY WALL BEHIND FRESH GP OF SUP DEPOT AT NAPIER ROAD AND PROVN OF TILLING JOINERY PLUMBING ALONGWITH SANITARY FITTINGS IN QTR

Amount

Demolition of Brick Work built in Cement Mortar including all Quoins, Arches, Pillars, etc. of any descriptions, complete all as specified and as directed.

Taking down Chowkat or Frame (without taking off Shutter from the Frame) n exc. 1.50 Sqm complete all as specified and as directed.

Dismantling Floor, Hearth or Wall Tiling including Cement Mortar Bedding (but not backing), and removing rubbish off the Premises, complete all as specified and as directed.

Taking down Cement Plaster of any description on Brick Walls, Concrete Surfaces including racking out joints, hacking for key, scrubbing down with Water, remove dust, debries/ rubbish, etc., complete all as specified and as directed.

Taking up or down Steel Water Tubing 15mm dia (bore) including Connections and Fittings, Segregating Serviceable Pipes & Fittings, Stacking properly at Site(s) and keep in Safe Custody for re-use, complete all as specified and as directed.

Excavating in trenches, n exc 1.50 m wide and n exc 1.50 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sqm on plan and n exc 1.5 m in depth and getting out in soft and loose soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm as in soft/loose soil complete all as specified and directed.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point as in soft/loose soil complete all as specified and directed.

M&L for Plain cement concrete 1:4:8, type D-2 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed.

M&L Plain Cement Concrete type C-1, (1:3:6) (20mm graded crushed stone aggregate) as in Coping bed plate,hold fast etc,block benching,channeling slightly rounded or chamfered angle and throating including form work and finishing all exposed faces of cement concrete complete all as specified and as directed.

M&L Reinforced Cement Concrete (Design Mix) M-25 in Foundations including Rafts, Footings, Foundation Beams; Plinth Beams; bases for Columns, etc.; Basement Slabs, Under-reamed Piles and Mass Concrete, complete all as specified and as directed. NOTE : Formwork and Reinforcement shall be Measured and Paid for separately under relevant Items.

M&L Reinforced Cement Concrete (Design Mix) M-25 as in slabs supported on walls,beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed. NOTE : Formwork and Reinforcement shall be Measured and Paid for separately under relevant Items.

M&L Reinforced Cement Concrete (Design Mix) M-25 in Roof Beams, Cantilevers, Bres-summers, Lintels over 1.50 Metre Span, complete all as specified and as directed. NOTE : Formwork and Reinforcement shall be Measured and Paid for separately under relevant Items.

M&L Reinforced Cement Concrete (Design Mix) M-25 in Columns, Pillars, Piers, Posts and Struts, etc. complete all as specified and as directed. NOTE : Formwork and Reinforcement shall be Measured and Paid for separately under relevant Items.

Cutting chase, pinning in making good to facing where required and pointing in CM 1:3 to end or edges of landing steps, cills, sunshades, shelves, lintels etc. and cutting chase for concealed water pipe etc. and making good cutting not exc 10Cm girth.

M&L fly ash bricks pulverizes using class 'A 'old size bricks straigth or curved on plan exc 6m mean radius built in CM (1:6) cmplete all as specified and directed.

M&L Brick Work pulverizes fly ash bricks ,Half-Brick thick, Old Size, built in Cement Mortar 1:4, Straight or Curved on Plan to any Radius, complete all as specified and as directed.

M&L Formwork to Sides of Concrete Foundations, Footings, bases of Columns, Raft and Raft Beams, Sides and Soffits (if any) of foundation and plinth beams and similar work; Square, rectangular or polygonal, vertical or to batter, flat, rough finished surfaces of concrete, complete all as specified and as directed.

M&L Use and waste of Formwork to Sides and Soffits of Floor or Roof Beams, Beam Haunchings, Girders, Bres-Summers, Lintels, Cantilevers, Shelves including supports, overhangs, etc. also splays between floors and beams, etc., flat, rough finished surfaces of concrete, complete all as specified and as directed.

M&L Use and waste of Formwork to sides of Pillars, Posts, Struts, Piers, Columns and stanchions, flat, rough finished surfaces of concrete, complete all as specified and as directed.

M&L for TMT bars 10mm dia and over, cut to length bent to shape required including cranking, bending spirally for hopping for columns, hooking ends and binding with and including mild steel wire (anealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L TMT Bars 5 to 10 mm dia, as in stirrups spacers and binders, cut to length, bent to shape required including crank-ing, bending and binding with and including Mild Steel Wire (annealed) not less than 0.90 mm complete all as specified and as directed.

M&L Framed Work such as Grills, Gratings, etc. with ends of Bars shouldered and/or riveted, or forged into Spikes; Framed Guard Bars; Barred Iron Doors; Ladders; Framed Balusters; Walk Ways; Railings; Framework of Water Tanks and Similar Work, conforming to Fe-290, Gde-E-165, complete all as speci-fied and as directed.

S&F Mild steel angle iron as in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

S&F Galvanised 2 strand, steel barbed wire 2.24 mm dia barbed with 2mm dia barbs at 75mm spacing and straining and fixing to any type of standard rails straining bolts, including securing or tying at crossing with and provision of galvanised mild steel wire staples or steel pins etc (each line wire to be measured) as in repair.complete all as specified and as directed.

S&F Concertina coil fencing with punched tape conertina coil 600mm dia openable length (total length 90 Mtr) having 50 nos rounds per 6 meter length upto 3.2 meter height of wall with iron angle 'Y' shaped placed 2.5 to 3.5m apart and stud tied with GI staples and GI clips to retain horizontal including necessary bolts or GI barbes and GI clips to retain horizontal including necessary bolts or GI barbes wire tied to angle iron, spring core, (2.5 mm thick) wire of height tensile strength of 165 Kg/Sq mm with tape (0.52 mm thick ) weight 43.478 gm/metre all complete as per direction of Engr-in -Charge

S&F Aluminium anodised (powder coated) Three track sliding window frame with shutters with ( 2 nos glazed and one wire gauzed shutter)including all necessary jointing cleats, hold fast, rubber gasket, snap beading and locking arrangements fixed with screws to wall etc. complete and glazing with and including 5 mm thick tinted glass to aluminium frame work using rubber gasket and including stainless steel wire cloth of 0.36 mm dia & average width of aperture 1.40mm with staple or suitable fillets wire mesh fitted with screws and washers etc including deco grill with the following section of frame and shutter (A) Sections for shutter (i) 'H' section 39 x 20 x 1.50 mm thick (ii) 'Interlock' section 39 x 20 x 1.50 mm thick (iii) 'Edge & Bottom' section 41 x 20 x 1.50 mm thick (B) Section for frame (i) Top & Sides 92mm X 29.70 X 1.50mm not less than 1.30 Kg /RM (ii) Bottom 92 X 29.70 X 1.50mm not less than 1.502 Kg /RM complete all as specified and directed .

S&F Powder coated aluminium ventilators with louvers and glazing including frame of section over all size of window 600X450mm complete with following specification . (a) Alu frames of size 45x45x1.2mm (b) Rail & Stile 45x45x1.2mm thick (c) 4.80mm thick frosted sheet glass Note :- All ventilators/louvers member including fitting & fixture shall be deem to included quoted rate. Only measure opening size of ventilators/louvers

M&L of powder coatd aluminium 50 micron anodised partition consist of single groove rectangular sectio 101.60x44.45x1.60mm (section jindal wt @ 1.301 kg/rm) including jointing cleats and glazing clips of fixing builder hardware fittings with 4mm thick ACP Shett including necessary fittings fixture aluminium snap beads. speats etc complete all as specified and directed

M&L for light or dark shade coloured digital vitrified ceramic floor tiles 10 mm thick (square/recatangular) area of each tile exc 0.18 sqm but nexc 0.36 sqm (600mm x 600mmx 10mm) as in floor etc set and jointed in neat cement slurry and pointed in white/coloured cement to match the existing floor make incl 15mm thick screed bed or bedding of layers in CM 1:6 complete all as specified

M&L Coloured glazed ceramic tiles in vertical surfaces 350x250x7mm/450x350x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick backing course in CM 1:4 complete all as specified and directed

Material and labour for coloured non skid ceramics tiles 7 to 8 mm thick (square/rectangular) area of each tile exc 0.11 sqm but not exc 0.18 sqm as in floors over and including 15mm thick screed bed beeding layer in CM 1:4 set and jointed in neat cement slurry and pointed in white coloured cement to match the existing floor make as a specified.

M&L Green Marble (of any type) Work (Table rubbed and polished) 18 to 20 mm thick, Cooking Platforms and like, Set in Screed bed of 20mm thick in Cement Mortar 1:4 including Pointing in White Cement 1:2 using Marble Dust with admixture of Pigment to match with Shade of Granite including Cutting and Polishing complete all as specified and as directed.

M&L Rendering 15mm thick in Cement Mortar 1:6 on Brick Walls or on Concrete Surfaces, finishing plastered surfaces Even and fair without using Extra Cement complete all as specified and as directed.

M&L Rendering 15mm thick in Cement Mortar 1:4 on Brick Walls or on Concrete Surfaces, finishing plastered surfaces Even and fair without using Extra Cement complete all as specified and as directed.

M&L Rendering 15mm thick in Cement Mortar 1:4 on Brick Walls or on stone masonry surfaces or surface other than fair face of brick-work or on one side of lathing, Even and fair without using Extra Cement complete all as specified and as directed.

M&L Preparing new Surfaces of Walls and applying Two Coats of Cement Base Paint over a coat of primer complete all as specified and as directed.

M&L for Preparation of new plastered surfaces and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed.

M&L for Preparation of new plastered surfaces and applying two coats of oil emulsion distemper (any colour/tint) over a coat of primer over 2 mm thick wall care putty (Birla/Asian) on wall surfaces including rubbing with emmery paper to make wall surface smooth and even complete all as specified and directed.

M&L Preparing new Steel or Iron Surfaces of any description, over 10 Cm width or girth and applying Two Coats of Synthetic Enamel Paint (First quality) over a coat of Red Oxide/ Zinc Chrome Primer, complete all as specified and as directed.

S&F for 20mm outer diameter CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed.

S&F in repair 20 mm bore brass MTA for CPVC pipes complete all as specified and directed

S&F in repair 20 mm bore brass FTA for CPVC pipes complete all as specified and directed

S&F in repair 20 mm bore brass elbow for CPVC pipes complete all as specified and directed

S&F in repair 20 mm bore brass Tee for CPVC pipes complete all as specified and directed

Supply and Fix 40mm dia PVC Pipe with bend complete fixed on walls ceiling and floors including GI PVC clamps beds sockets etc incl taking down unserviceable old PVC Pipes complete all as specified and directed

Supply and fixing in repair 10 litre capacity low level PVC flushing cistern (any colour), syphonic action type, with inlet, ball valve, float, handle, fixed with cast iron bracket (of suitable size) and providing 32 mm dia PVC flush pipe and making all necessary connections complete as directed.

Supply and fix Vireous China Wash down water closet Pan (Pedestal Pattern) White including fixing Bots (excluding Flushing Cistern and Flushing Pipe) with plastic water closet seat, Black, Closed Pattern with recessed Bottom and Cover including Mild steel Chromium Plated Aluminium Hanging Device and including taking out unsv WC and Making Good disturbed surfaces with Cement Mortar 1:3 complete all as specified and as directed

S&F in repairs 125mm size Chromium plated shower roses with or without swivel joints, any size, including fixing to steel pipe or union complete all as directed by engineer-in-Charge.

S&F in repair 3-in-1 wall mixer for Hot and Cold water supply with telephonic shower arrangement cast copper ally cromium plated fancy type screwed down for iron pipe incl necessary fittings and fixtures etc complete all as directed

S&F in repairs central hole for Hot and Cod water supply basin mixer cast copper alloy chromium plated screwed down for iron pipes, including necessary fittings etc complete all as directed

S&F in repair bib cock 15mm bore fancy type cast copper alloy chrormium plated fancy type with wall flunch concealed type screwed for iron pipe or for brass ferrule etc completed all as specified and directed

Supply and fixing in repair two way bib cock 15mm bore with flange cast copper alloy chromium plated fancy type screwed for iron pipe brass ferrule etc complete all as directed

Supply and fixing angular stop cock 15mm dia cast copper alloy chromium plated fancy type with wall flunch concealed type screwed for iron pipe etc complete all as directed including taking down old Unsv stop cock

Supply and fixing in repairs stop cock 15 mm dia half turn dia cast copper alloy but fancy type chromium plated screwed for iron pipe etc complete all as directed including taking down old unserviceable stop cock.

Supply and fix in repair CP Grating 100 mm size fixed with white cement complete all as directed

Supply and fix in repair CP Health Faucet with 1 Mtrs Tube and Hook all as directed by Engineer-In -Charge

M/S ANUJ KUMAR

ARATI TRADING CO

NUPUR CONSTRUCTION

M/S L.R.ENTERPRISES

DILIP CONSTRUCTION

INDIA ELECTRICAL EQUIPMENTS

DEB AND COMPANY

M A ENTERPRISES

SEN ELECTRIC WORKS