Construction of New Library at Anna Nagar Chennai

Amount

Removing the existing ventilators,doors and windows including removal of frames, hinges and fastenings carefully and stacking the same at site etc., complete

Dismantling the existing brick or stone masonry work in cement mortar under 3m high including carefully clearing the debris etc.,complete.

Dismantling RCC by manual / by using deploying machineries carefully clearing away the debris as directed during execution. The dismantling of concrete as per PWD schedule of rates are to be adopted wherein a part part of the concrete only is to be dismantled and the remaining part of the concrete has to be retained structurally safe.

Dismantling, clearing away and carefully stacking materials :Floor finish & dadooing walls in cement mortar with Mosaic Tiles / Glazed Tiles / Clay Tiles / Cuddapah Slabs

Dismantling, Plain cement concrete and clearing away the same 50 m away from the site and roughening the surface etc., complete complying with standard specification and as directed by the Departmental officers.

Earth work excavation for foundation in Hard stiff clay, stiff black cotton, hard red earth, shales murram, gravel,stoney earth and earth mixed with small size boulders and Sand, silt or other loose soil, wet sand,or silt not under water, light black cotton soil, sandy loam ordinary soil and to full depth as may be directed except in hardrock requiring blasting inclusive of shoring shuttering and baling out water and cleaning and levelling the site etc.,complete SS.20B

Narrow Foundations for building & culvert- First Depth Upto 2m

Narrow Foundations - Second Depth 2m - 3m

Providing and constructing cast in situ hydraulic bored piles of 375mm diameter in M30 grade concrete using blended cement - slag cement with minimum cement content of 400kg/m³ in accordance with the structural engineers drawings and directions, but exculding reinforcement including cost of mobalization of all necessary plants, equipment's like piling rigs, temporary casing of appropriate length for setting out cardinal points and the removal of the same, boring in overburden, using bentonite mud circulation technique or any other method duly through all strata upto the foundation level of piles etc., complete all as approved by the departmental engineer. Further include dewatering, placing concrete by tremie pipe method, disposal of bored material outside the site. Including Chipping carefully cut off portion of piles as required without any damage to the piles and dressing the top and removing all the debris away from the site with out any extra cost as directed including the cost of all tools, plants, conveyance, all labour, lead and lift required etc ., Conducting standard penetration test to identify the refusal strata for atleast 1 pile in group and atleast 25% of piles, comparing with refusal strata as indentified in soil report and providing socketting into refusal strata by 1.00mt or into hard rock by 100% dia of the pile. (Length of pile for payment shall be measured up to bottom of pile cap).

Providing and constructing cast in situ hydraulic bored piles of 450 mm diameter in M30 grade concrete using blended cement - slag cement with minimum cement content of 400kg/m³ in accordance with the structural engineers drawings and directions, but exculding reinforcement including cost of mobalization of all necessary plants, equipment's like piling rigs, permanent casing of appropriate length for setting out cardinal points and the removal of the same, boring in overburden, using bentonite mud circulation technique or any other method duly through all strata upto the foundation level of piles etc., complete all as approved by the departmental engineer. Further include dewatering, placing concrete by tremie pipe method, disposal of bored material outside the site. Including Chipping carefully cut off portion of piles as required without any damage to the piles and dressing the top and removing all the debris away from the site with out any extra cost as directed including the cost of all tools, plants, conveyance, all labour, lead and lift required etc .,Conducting standard penetration test to identify the refusal strata for atleast 1 pile in group and atleast 25% of piles, comparing with refusal strata as indentified in soil report and providing socketting into refusal strata by 1.00mt or into hard rock by 100% dia of the pile. (Length of pile for payment shall be measured up to bottom of pile cap).

Initial pile Load test (excluding pile cost) (Design load)

Supplying and filling in foundation and basement with Crushed Stone Sand (M- Sand) in layers of not more than 15cm thick well rammed watered and compacted etc., complete complying with standard specification.

Supplying and laying of Sand Gravel Mix in ratio 1:1 for using 0.631 m3 of sand fo filling and 0.675 M3 of red gravel of 1m3 of volume including cost of sand gravel mix including labour charges for mixing , laying compaction all tools and planks employed etc., complete complying with standard specification and as directed by the departmental officers

Construction of Wet Mix Macadam 150mm compacted thickness in two layers by providing laying , Paving , and compacting of aggregate gradation satisfying to Table 400-13 of MORTH and satisfying he physical paraemeteres as per MORTH Table 400-12, mixing in a Wet Mix Plant of 200 tonne capacity at OMC , carriage of mixed material to work site and laid in sensor pavers tc the required line and grade as per the drawing and compacted with vibratory roller of 8-10 tonne to achieve the desired density of 98% of Maximum dry density and as per the direction of the Engineer In-Charge of work

Providing pre-constructional Antitermite treatment including cost of chemicals labour as per standard specifications for preparing the area for treatment by spraying chemicals and other incidental charges etc.. complete. The rates should be for antitermite treatment from the plinth beam and brick masonry with super structure in contact with the back fill earth and at the junction of the walls. The top surface of filled earth for flooring and the soil along with the perimeter of the building by making holes with the crow bar and poured 5% termicide “Chloripyrifos” and spraying the same termicide solution on the wooden frames and treating the other periphery of buildings etc., complete in all respects as per IS 6313 (part II) / 1981 and as directed by the departmental officers.

Plain Cement Concrete 1:4:8 (one part of cement, four part of Crushed Stone Sand (M- Sand) and eight part of coarse aggregates) using 40mm size ISS HBG metal including cost and conveyance of all materials to site and including for the mixing, laying and labour charges and all incidential charges such as water providing etc., complete as per standard specification

Supplying and erecting centering for sides and soffits including supports and strutting up to 3.30 m height with all cross bracing for plane surfaces as detailed below, using mild steel sheets of 90 X 60 cm 10 gauge stiffened with MS angle of 25 X 25 X 3mm for boarding, laid over adjustable span & jacks and supported by 50mm dia pipes for general pipes scaffolding systems @ a spacing of 1.20m c/c and vertical connected at a height of 2.0m c/c including 'C' & 'U' clamps and base receiver cup at bottom for connecting pipes etc and removable systems etc.,Rate to include all materials, labour charges, wastages , placing, transportation, lead & lifts, tools & plants, fuels, fixing in position at all levels, heights, masking tape in sheet joints, consumables, etc. as complete with all respects complying with relevant standard specification, as directed by the Client / Engineer-in-charge.

Reinforced cement concrete Column footing, plinth / grade beam, bed blocks, template surfaces, steps, piers, raft slab / beams and such other members

For plane surfaces such as recangular or square columns, sunshades, top and bottom slab of boxing, kitchen platform, loft and such other structural members

Plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slab / beams and such other members

For circular columns

For plane surfaces such as vertical slab, side slabs of boxing, vertical drops, facia, vertical wall, etc.

Providing and Laying M 30 Design Mix for all reinforced cement concrete with minimum cement content conform to IS 456-2000 using ordinary Portland cement of grade 53 from approved manufacturer, manufactured sand, 20 mm and down graded size coarse aggregates, necessary approved admixtures as per requirement. works for Raft, Grade beam, Shear wall, RCC walls, Lift walls, Plinth beams, Column, footings, Grade slab, Roof slab & beam, Curved slab, beam, Column drops, Pergola, Staircase waist and landing slab lintel, Sunshades, parapet Cum drops, Steps, canopy, window boxing slab, Loft, fins facia Planter box binders basement retaining wall, machine foundation, elevation features and other similar structures etc..excluding necessary centering, shuttering and reinforcement which shall be measured and paid separately under relevant items. Rate to include all leads, lifts, tools & plants, fuels, all materials, labour charges, wastages , laying, pumping the concrete to all levels, providing sleeves / openings in RCC slabs, compaction by vibrator, curing etc. as complete with all respects complying with relevant standard specification, as directed by the Engineer in charge

For Foundation & Basement

Ground floor

First floor

Second floor

Terrace floor

Weathering course-using Concrete broken brick jelly 20 mm gauge in pure slacked lime (No sand to be used) over RCC roof slab. The proportion of broken brick jelly to slaked lime being 32:12½ cft well beaten by wooden beaters for giving required slope and thickness required etc complete complying with standard specifications and as directed by Departmental Officers.

Supplying, fabricating and fixing in position of steel Fe 550 grade Reinforcement for all RCC work with Thermo Mechanically Treated Bars (TMT) conforming to IS 1786 of latest version according to drawings and binding the reinforcement with 18 gauge double fold GI binding wire and providing Concrete / PVC cover blocks to maintain the cover as required.Rate to include all bending, tying grills, placing, transportation, lead & lifts, tools & plants, fuels, all materials, labour charges, wastages , laying at all levels, fixing in position, cost of cover blocks, etc. as complete with all respects complying with relevant standard specification, as directed by the Engineer-in-charge.

Supply and constructing Fly ash Brick masonry in Cement Mortar 1:5 (One cement and Five M sand) in foundations, basement and superstructure using Fly ash Bricks of size 230x110x75mm etc. Rate to include all materials, labour charges, wastages for working at all levels with necessary lead and lifts, transportation charges, loading, unloading, scaffolding, staging, curing, fuel, consumables as complete with all respects complying with relevant standard specification and as directed by the Client / Engineer-in-charge.

For foundation & basement

For Ground floor

First floor

Second floor

Terrace floor

Supply and constructing Flyash Brick partition wall 115mm thick in Cement Mortar 1:3 (one cement and three M sand) 11.50 CM thick using using Fly ash Bricks of size 230x110x75mm including both side plastering with CM 1:5 12mm thick and using hoop iron reinforcement if found necessary and hoop iron shall be supplied to the department at free of cost etc., complete as directed by the Engineer in- charge.

For Ground floor

For First floor

For Second floor

For Terrace floor

Special ceiling plastering and finishing all RCC exposed surfaces such as RCC slabs, sunshades, canopies, stair case steps, landing slabs etc with CM 1:3 (One cement and three sand) 10mm thick including hacking the surfaces and providing necessary CM nosing, beading as per size specified wherever necessary using the same mix etc., complete complying with standard specification and as directed by the Departmental Officer.

Inner Plastering with cement mortar 1:5 (One part of Cement and Five part of Plastering Sand (P- Sand)) 12mm, thick in all floors including cost and conveyance of all materials to site and labour charges etc, complete as per standard specifications

Outer Plastering with cement mortar 1:4 (One Part of Cement and Four part of Plastering Sand (P- Sand)) 20mm thick in all floors including cost and conveyance of all materials to site and labour charges etc, complete complying with standard specifications.

Waterproofing: Providing and Applying CFTRI approved two component flexible polymer modified acrylic cementitious waterproofing coating with a mix ratio of (5 Liquid :7 Powder) to the RCC surface of the UGT/ OHT tank applied @ 2.2kg/m2 in 2 coats to achieve 1.2mm DFT, having Elongation at break >120% as per ASTM D 412, Tensile strength >1N/ mm2 as per ASTM D 412, Adhesion strength: 0.80N/mm2 as per ASTM D 4541, crack bridging upto 2mm as per ASTM C 836. The finished cost to include surface preparation, making coving of 50 mm X 50mm at all right angles of wall Junction with Polymer Repair Mortar and lay 45 gsm glass fibre mesh over the angle fillet when the first coat in still wet, treatment of cracks completely as per specification. Followed by applying 15 mm thick dimensionally stable fibrous reinforced cementitious structural grade dual shrinkage Polymer Mortar on as protective plastering @ 29kg/m2. The material having Compressive strength of 38 MPa at 28 days as per EN 12190, Adhesive Bond Test, >1.5 Mpa as per EN 1542, followed by Water curing by sprinkling water for 3 times a day for 5- 7 days. Followed by applying two component, water-based food grade epoxy resin coating on inside surface of Potable water tank having anti algae, antifungal, Non-toxic, hygiene cum damp-proof coating Certified by CFTRI as per 21 CFR 175 – 300 of US – FDA, having mixing Ratio (Base: Hardener: Water) – 1:1:1 to be applied @ 0.35 Kg/m2 in 2 coats. Ensure that this coating is applied over the protective plaster. The Waterproofing material shall have Specific Gravity: 1.2, Water vapor permeance: 244.48 g/m2/24 hrs, as per IS 7809/Pt 2/1977, Adhesion strength: 2 N/mm2 as per ASTM D 4541: 02. The finished cost to include surface preparation completely as per specification.

Providing and Applying CFTRI approved two component flexible polymer modified acrylic cementitious waterproofing coating with a mix ratio of (1 Liquid: 2 Powder), to the RCC surface like bathroom, toilet, balcony & utility area applied @ 1.7kg/m2 in 2 coats to achieve 1mm DFT, having Elongation at break >50% as per ASTM D 412, Tensile strength >1N/ mm2 as per ASTM D 412, Adhesion strength: 0.80 N/mm2 as per ASTM D 4541, crack bridging upto 1mm as per ASTM C 836, Water penetration (5 bar pressure) as per BS EN 12390. The finished cost to include surface preparation, making coving of 50 mm X 50mm at all right angles of wall Junction with Polymer Repair Mortar and lay 45 gsm glass fibre mesh over the angle fillet when the first coat in still wet, treatment of cracks completely as per specification.

PVC mould CI Steps for Sump

Manufacturing, Fabrication, Supply and delivery of Aluminium ladder 6m height Folding type for operating inside the pumproom made out of Aluminium “ Џ “ channel 3” x 1 1/2” , 4mm thick for sides and steps in “L” channel 3” x 1 1/4” , 4mm thick @ 45cm width, 30cm c/c providing with suitable roller, rope, rubber bush etc. including cost of all materials, labour etc.

Painting the new plastered walls with two coats for Interior Plastic Emulsion paint approved quality and colour over a priming coat, with two coats of wall putty including thorough scrapping, clean removal of dirt, etc complete and including necessary plaster of paris, putty, wherever required etc, complete as per standard specification.

Painting two coats for Exterior surface with approved Exterior Plastic Emulsion paint approved quality and colour over a priming coat, including thorough scrapping, clean removal of dirt, etc complete and including necessary plaster of paris, putty, wherever required etc, complete as per standard specification.

Painting the wall with Texture Finish Paint approved quality and colour over a priming coat, including thorough scrapping, clean removal of dirt, etc complete as per standard specification.

Providing Microcment Plaster with Following Specifications Microcement is prepared from a powder component (microcement base for the preparation of the works and microcement fine for the finish) and a liquid component. These two components must be mixed homogeneously according the following proportions: • Microcement Base (microcement base: preparation mortar) 10 kg of powder must be mixed with 3 liters of concentrated liquid • Microcement Fine (microcement fine: finishing mortar): the mix will be done as follows; for 10 kg of powder approximately 4.5 liters of liquid will be used The mortar must be prepared as follows: 1. Pour little amount of resin (component B) into a container, then add the quantity of pigment required according to the amount of microcement to be used, and then mix them up until a uniform colour is achieved. 2. Pour gradually the Microcement powder (component A). Add the powder as the product is mixed with a slow speed mixer drill. 3. Mix for at least 2 minutes until the mortar is smooth and free of lumps.

Painting the new Iorn work with two coats of Ready Mixed Enamel Paint of aproved quality and colour over the existing priming coat including the cost all materials etc.,complete, in all floors and as directed by the Departmntal Officers.

UPVC Window Specification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges

UPVC Ventilator Specification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride)louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work.

Fabricting Supplying and fixing in position aluminium anodised Natural color matt finish window using 5.50mm thick Plain glass at top with aluminium grill 10mm thick double leaves dooors with suitable frames and necessary accessories such as rubber beading PVC felt, handle for a length of shutter (both sides), locking arrangements, Furniture fittings.

Providing and fixing Vertical blinds , quality of approved make fabric made of 100% polyester woven fabric thickness 0.40mm with virtually maintenance free having plastic bottom chain thickness of chain-0.50mm and diameter-3mm, Plastic with metal bottom and suitable coating on exterior, including all fixtures and fittings complete in all respect as per design/color/shade including requisite installation brackets etc as required for installation at site with anchoring arrangements complete.

Best Indian Teak Wood Panelled door in double shutters with frames 100x75mm at side,verticals and top. The shutters shall beof 40mm thick with moulded panels in 20mm thick planks,6Nos.of iron hold fasts fixed in c.c.1:2:4 6Nos.of butt hinges 125mm long including wind appliances, furniture,iron fittings,1No.of iron padlock 15cm long for locking arrangements and fixing inposition,etc.,complete.(ISI STD)

Fabricting Supplying and fixing in position aluminium anodised Natural color matt finish Door of using 5.50mm thick Plain glass at top with aluminium grill 10mm thick double leaves dooors with suitable frames and necessary accessories such as rubber beading PVC felt, handle for a length of shutter (both sides), locking arrangements, Furniture fittings.

Providing and fixing casement doors fabricated from unplasticized polyvinyl chloride (uPVC) sections. Profiles: The profiles should be three chamber system which provides high insulation properties with outer frame 60mm x 55mm with an outer wall thickness of 2.4mm. The window unit should be designed with all corner joints mitred and fusion welded. Windows should be steel reinforced with 25 x 24 x 25mm steel reinforcement with a thickness of 1mm to have dimensional stability. The sash should be of 60 x 102mm. The mullion should be of 60 x 74mm. The profiles should have co-extruded seals. Hardware: All the hardware like friction stays, handles should be screwed with self tapping screws. The handles, locks should be designed so that they cannot be released from outside. Glazing: The window system should be glazed with 5mm plain float glass / 6mm bison lam Installation: The profiles should be cut to length and welded 45 degrees. The window should be designed such that the water drainage does not pass through the reinforcement chamber. The window system should be fixed directly to the plastered brick wall using self expanding nylon plug and driving ms electroplated screws into plug.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/ Ceosetory windows & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. Note: For WPC solid door/window frames, minus 5mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. Frame size 50 x 100 mm

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges 100mm of required thickness with necessary full body threaded star headed counter sunk S.S screws/ welding wherever required necessary etc all as per direction of Engineer-In- Charge.30 mm thick

STEEL DOOR Fabricating Supply and fixing and position of MS doors with single leave. The door outer frame will be 40x40x6mm MS angle, the shutter frame will be 35x35x6 mm, MS angle intermediate stiffner will be 35x35x6 mm with cross stiffner 25x 25x5 mm flats covered with 18 gauge M.S. sheet with necessary hinges, tower bolts, aldrop length 30mm and hold fast etc., complete with one coat red oxide primer.

Supply and erection of Double Leaves Fire Rated Door with Frame having the dimension of 1800mm x 1400mm with following specification: a. Door Frame 1.6mm: Galvanized 120 GSM branded make JSW b. Door Leaf 1mm: Galvanized 120 GSM branded make JSW c. Shutter Thickness: 46mm d. Honeycomb: In-fill e. Glue Macroplast UR-7221 f. Door Hinges: 4” x 3” x 3mm, Double Ball: Make Assa Abloy Yale Ball bearing Butt Hinges Grade SS 304 - Finish SS g. Door Closer with Standard Arm Finish: Silver h. Lock Set: Dead Lock with both side key i. Door Orientation: To be confirmed by client j. Mounting of door: Brick wall mounted k. Powder Coating: Powder coated in standard RAL paint colour of PO Red (60 to 90) Microns l. Single Point Panic Bar (2 Horizontal): Make Assa Abloy Yale or Equivalent m. Dead Lock with both side key: Make Assa Abloy Yale or Equivalent n. Vision Panel 200 x 300mm 2 Hrs. Fire Glass Schott Pyran with Frame o. Rated Glass Schott Pyran with Frame p. Anchor Bolt with Endcaps The above assembly mounted on concrete or brick wall including the cost of cutting, chipping, concrete packing, pastering, scaffolding all other conveyence as per standard methods and as directed by the Departmental Officers.

Supplying, Fitting, Fixing and Installation of Merino Besco TITAN 12MM BOX UP series cubicles (or approved equivalent make) of width and depth as per specifications/ site drawings.Cubicle height to be 2100 mm and/or as perrequirement/site conditions. Length & breadth of the cubicles shall be as per requirement and /or as per site conditions. ITEM-DESCRIPTION:- Made from solid grade compact high pressure laminate as per IS:2046 and EN 438 manufactured under high specific pressure > 5 MPa and temperature >120°C with bunch of Kraft papers impregnated with thermosetting phenolic resin and decorative papers made of Alpha cellulose fibre impregnated withthermosetting melamine resin which provide superior scratch, abrasion, heat, chemical, impact, graffiti & moisture resistance along withanti-bacterial properties. Panels have a black corethat when machined, presents a distinctive black edge. Doors: All doors will be of single colour and made of 12 mm thick Merino HPL compact panel. The doors will have chamfered edges. Each door will be supported by 3 stainless steel made hinges affixed tothe pilasters. Stainless steel made coat hook and lockset are provided with each door. All the doors will be routered at the vertical ends and the rubber spongelining will be incorporated at the routered ends. Pilasters: All pilasters will be made of 12 mm thick Merino HPL compact panel with chamfered edge and completed with stainless steel made thumb turn lock set. Pilasters will be anchored to the floor using steel made Lbrackets and box up fixtures are used for covering the floor anchored mechanism. All pilasters will be routered at their vertical ends to facilitate closure of doors. The bottom gap is 100 mm. Dividers: All intermediate partitions or dividers will be made of 12 mm thick Merino HPL compact laminate panels. They are affixed with stainless steel made U-channel at their ends for ultimate stability of the system. Design no. as specified by Arch. / Engr. in suede finish. Size of panelsto be as per drawing / as per requirement/ site conditions. HARDWARE & ACCESSORIES: • Top rail is made of stainless-steel grade 304. A thin plastic film pasted for surface protection.Dimension is 55mmx42mmx1.6mm-Tee. • Corner joinery section made from Stainless steel grade 304. Surface finish to be brush type. A thin plastic film pasted for surface protection. Size to be 35mmx15mmx0.8mm-Tee. • Wall joinery section with hamming profile made from Stainless steel grade 304. Surface finish to be brush type. A thin plastic film pasted for surface protection. Size to be 21mmx16mmx0.8mm-Tee. • Fixed front panel to be anchored to floor with L Bracket of SS and covered with SS 316 Grade Box Type plate from all directions with 100mm clear Height from ground. Surface finish to be matt-type. • Spring loaded Butt Hinges made from Stainless steel grade 304. Surface finish to be matt type. Covers to be lacquer coated. • Coat hook with rubber stopper made from Stainless steel grade 304. Surface finish to be matt-type. • Round Door knob diameter 30 mm with grooves for better hand grip made from Stainless steel grade 304. Surface finish to be matt-type. • Rotating Thumb-turn locking system with privacy indicator made from Stainless steel grade 304. Surface finish to be matt type. • Anti-noise rubber padding of thickness 2 mmand width 10 mm • Stainless steel grade 304 screws. Material: Merino Make or Approved Equivalent Mode of Measurement: - From finished floor to top of cubicles, as and where found the physical height of the finished structure . No wastageshall be considered for measurement purpose. Merino Make or Approved equivalent material

Paving the floor with Granite flag stone of varieties size over a cement mortar bed of 20mm thick using cement mortar 1:3 (One Cement and three crushed stone sand) fixing the slabs with required cement slurry and laid in true right angkes with minimum possible width of joints with white cement mixed with matching colouring pigments etc.,

Providing and laying Flagstone 600x600x65mmsize over a cement mortar bed of 20mm thick using cement mortar 1:3 (One Cement and three crushed stone sand) fixing the slabs with required cement slurry and laid in true right angkes with minimum possible width of joints with white cement mixed with matching colouring pigments etc.,

Supplying And Fixing Rubber Moulded Interlocking Paver Blocks Against Available Edge Restraints 80 mm Thick of Approved Design And Pattern of Strength 40 N/Sq.m. 10 mm Iss Metal With Minimum Cement Content As Applicable To M 40 Grade Concrete As Per Is-456-2000 Manufactures By Mechanical Or Hydraulic Machine Using Vibro- Compaction Process And Laid Over 50 mm Thick Laying Course (Bedding) Crushed Stone Sand (M Sand) Well Compacted By Plate Compactor With A Joint Width of 2 mm To 5 mm Including Filling of All Joints With Crushed Stone Sand (M Sand) And Compacting The Paved Surface With Plate Compactor Two Or Three Times Until All The Unit-To- Unit Joints Are Completely Filled With Crushed Stone Sand (M Sand) And Trimming The Edges Neatly Including All Labour Charges And Plate Compactor Charges Etc. Complete(Cost Inclusive of Crushed Stone Sand (M Sand))

Supplying and laying Grass Paver block M40 grade Providing and laying of 63mm thick high strength type conforming IS 15658-2006 of rubberized interlocking paver lock in size of minimum compressive strength of 40N/mm2 in uniform shape of approved make to be laid in flurring bone pattern with sand cushion below the uniform shap of approved non skitting surface in the top and the rate including levelling the base preparation of pavers as sub base, sand cushion 150mm thick laying out of pavement cut the pieces to fix the edge vibring the pavers,sweeping tranporting loading unloading of laying paver block as per standard specification,.

Supplying And Fixing of Rubber Moulded Grey Premium Concrete Kerb of Size 450X125X300mm Using M30 Concrete. The Concrete Shall Be Moulded By Table Mount Vibrated With Polypropylene Fibers At 5% And Curing Compound. The Rate Shall Include Cost of Materials Transportation Loading Unloading Charges And All Taxes Including Necessary Earth Work Pointing With cm. 1:3 To Full Depth Curing Thread Lining Etc Complete .

Providing and laying of Black Granite Cobble Stone flooring of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement: 4 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete.

Paving the floor with Double charged Vitrified tiles of approved quality and colour of size 600x600x8mm thick of approved make, quality and colour in all floors over a base layer of cement mortar 1:3 (One part of Cement and Three part of Plastering Sand (P- Sand)), 20mm thick and laid straight alignment and pointed neatly with colour cement at the rate of 0.40kg/m2 laid without any air gap in the tiles neatly and fixing in position as per standard specifications and as directed by the departmental officer. The colour & quality of tiles should be got approved by Municipal Engineer before use on work

CARPET TILES- Supplying and installing Environmental Friendly carpet tiles 500 x500 Antibacterial with approval color as per the Code, Completed work including cutting, placing, using appropriate gluing material,...etc. which should making necessary opening for floor boxes whenever requested or directed by the Engineer, Different samples must be submitted for review and approval prior of starting the delivery and installation works.

Supplying and installing Woven vinyl tile carpet tiles 500 x500 Antibacterial with approval color as per the Code, Completed work including cutting, placing, using appropriate gluing material,...etc. which should making necessary opening for floor boxes whenever requested or directed by the Engineer, Different samples must be submitted for review and approval prior of starting the delivery and installation works.

Paving the floor with Double charged Vitrified tiles of approved quality and colour of size 1200x2400x9mm thick of approved make, quality and colour in all floors over a base layer of cement mortar 1:3 (One part of Cement and Three part of Plastering Sand (P- Sand)), 20mm thick and laid straight alignment and pointed neatly with colour cement at the rate of 0.40kg/m2 laid without any air gap in the tiles neatly and fixing in position as per standard specifications and as directed by the departmental officer. The colour & quality of tiles should be got approved by Executive Engineer before use on work

Paving the floor with design Antiskirt ceramic tiles (colour and shade as directed) of size 600 mm x 600 mm x 6 mm in all floors over a base layer of cement mortar 1:3 (One part of Cement and Three part of Plastering Sand (P- Sand)), 20mm thick laid in-situ and pointed with same coloured cement

Supplying and fixing Dadooing the wall with ceramic tiles of approved quality, colour and design joint free of size 600x300x10mm thick of approved make, in all floors over a base layer of cement mortar 1:2 (one cement: Two sand) 10mm thick and laid straight alignment and pointed neatly with colour cement at the rate of 0.40 kg/m2 laid without any air gap in the tiles neatly and fixing in position as per standard specifications. The rate including cost of all materials, labour charges, wastages, necessary lead and lifts, working at all levels, transportaion charges, loading, unloading, the same before handing over as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge.

Supply and laying with best quality the following materials of Machine Flamed Steel Grey Granite Slab 1200mm x 600mm, 16mm to 18mm Thick including cutting and edge polishing to be set in CM 1:3 (1 of cement : 3 of manufactured sand) 20 mm thick including finishing the joints with white cement slurry, cutting, edge chamfering to approved shape and polishing rough, medium, nice and tin-oxide polish.Rate including all materials, labour charges, wastages, necessary lead and lifts, working at all levels, transportaion charges, loading, unloading, preparation of surface, ncessary haccking in RCC surface, cutting to required shape, edging, tools and plants, fuel, curing, cleaning, acid wash over finished surface, protection with Gypsum / Pop layer over plastic sheet and removing the same before handing over as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge.

Nosing for Granite Slab - Single Nosing

Nosing for Granite Slab - Double Nosing

Nosing for Granite Slab - Grooving the Granite slab

Finishing the top of roof with one course of Solar Reflective ceramic tiles of size 305 mm x 305 mm x 7 mm of approved quality in Cement Mortar 1:3 (One part of Cement and Three part of Plastering Sand (P- Sand)), 12 mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete

Flooring with Double charged / multi charged stain free full body porcelain vitrified tiles with double layer pigment of Size 600 x 600 mm and thickness between 8-10 mm and 1st quality conforming to IS:13711, IS:13712, IS:13630 (Parts 1 to 15) of any colour and finish in all shades and designs set over a base coat of CM (1:8) prop. 12mm thick over CC bed already laid or RCC roof slab , including neat cement slurry of honey like consistancy spread @ 3.3 kgs per Sqm. and jointed neately with white cement paste mixed with pigment of matching shade to match the shade of tiles to full depth including cost and conveyance of all materials like cement, sand, water, tiles, white cement etc., to site (excluding cost of C.C. bed), cost of base coat and all labour charges for mixing of cement mortar, laying tiles to required slope as directed by the Engineer- in-charge including cost of overheads & contractors profit etc., complete for finished item of work.

Providing and filling the tile joint with epoxy grout with following specification: Surface preparation including cleaning the joint to be free from dust and loose particles. Providing masking tape on either side of the tile joint edges and providing sealing the tile gap with epoxy tile joint grout and finishing neatly and as directed by the departmental officers. The rate inclusive of cost of materials and labour, etc., complete.

Providing and applying a 15 mm thick Stone Crete Plaster Finish on vertical surfaces, consisting of a blend of Ordinary Portland Cement (OPC), crushed stone or decorative pebbles, fine marble powder, chemical hardeners, and potable water. Preparing the wall surface by roughening it adequately to promote adhesion, ensuring it is free from dust, grease, and loose particles. Applying the mixture uniformly to the prepared wall surface to the specified thickness, and before the plaster sets, expose the aggregates by washing or brushing to achieve the desired textured finish. Provide curing to ensure optimal strength and durability, resulting in a consistent, exposed aggregate texture as per the approved sample. All materials and workmanship shall conform to relevant Indian Standards and the specifications outlined by the Tamil Nadu Public Works Department (PWD).

Providing grooves for 25mm width 10mm Deep

SUPPLY AND INSYTALLATION OF EVERWOOD DECKING : Everwood composite EWD146x23D deck board fitted on hollow aluminium joist EWD50x30EDx1.5mm framework. Framework fitted on floor with intervals not exceeding 350mm c/c with aluminium L-clamp & Boss240 -adhesive solution as designed. Composite plank fitted on joist with SS304 grade start & end clips / PA grade center clips fastened with corroshield 7x25CSK screws. Necessary sides to be covered with EWD57X10 trims as specified and finished all complete

Providing fixing and pasting Wall paper as per design & details. The item includes making POP base to get a uniform smooth surface. (base Price Rs. 100/ sqft.without taxes) The fixed area of wall paper shall be considered for payment and not the area of procured material.

Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer, 3mm thick water proofing membrane, black finished reinforced with glass fibre matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 ltr/sqm. by the same membrane manufactured of density at 25°C, 0.87 - 0.89 kg/ltr and viscocity 70 - 160 cps. Over the primer coat the layer of membrane shall be laid using butane torch and sealing all joints etc., and preparing the surface complete. The vital physical and chemical parameters of the membrane shall be as under : Joint strength in longitudinal and transverse direction at 23°C as 350/300 N/5cm. Tear strength in longitudinal and transverse direction as 60/80N. Softening point of membrane not less than 150°C. Cold flexibility shall be upto -2°C when tested in accordance with ASTM, D - 5147. The laying of membrane shall be got done through the authorised applicator of the manufacturer of membrane:

Art work as per the direction of department official, over Oil Painting with first class quality and approved colour including a priming coat with thorough scrapping clean removal of dirt., etc., complete and including necessary plaster of paris, putty, etc., wherever required (Relevent ISI STD), including putty works.

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete

Providing two legged scaffolding using 15cm dia casuarinas post of 4.0 m over all length of (3 M Height+0.5 M over all length (3.0M height +0.5m projection +0.5m in to the ground ) the distance between the two rows being 1.25M and the spacing of posts being 2.0M in both the rows with two horizontal posts with 0.5M overlap on either side and braces at 2.0M centre to centre including longitudinal and traverse middle braces to step up and transverse middle braces to step up and providing a plat form with country wood planks of 40mm thick and 1 M width ,etc in a complete form using coil and nails (Rate for an initial height of 3.0M and length of 1 M)

Scaffolding charges for every additional height of 2.5 M height over the initial height of 3 m.

Supply and fixing Shade net (Green Net) for under construction of high rise building

Supplying and fixing in position of Alu. Anodised Partition with 62x38x2mm extruded box section at bottom vertical and horizontal members. The vertical member are spaced at 90 cm c/c and to horizontal members are spaced at 1.2M, 2.1M and 2.4M height the bottom panels should be covered with 12 mm thick PLB exterior grade and the top and middle panels should be fixed at 4mm thick glass thick glass with necessary glassing clips.rubber beading, etc., including necessary dismantling holes in RCC columns, beams masonry wherever necessary with power power drill ti the extent required and made good to the original conditions after fixing as directed by the departmental officers. All the Aluminium sections should be anodised to 1.5microns as per ISI specification 1868/1962.

Fabricating supplying and fixing of pre painted galvanium colour sheets with the following specification. The materials should be of PPGI tile profile with a red colour or any other approved design 0.47 mm thick 24 guage having width 1050 mm. The sheet should be G.I.base pre painted hot dipped galvanized iron sheet and to be fixed with shelf tapping screws,plastic washer.The washer and screws to be fixed by using minute power machine drilled with out damaging the sheets paint coating to be regular modified polyster coat with zinc coating of Z 120 GSM paint thickness the finish should be terra cotta finish like malabar mangalore tiles finish optional matt finish. The sheet to be fixed with making suitable corrugated,cutting the sheet in to the required ssize and making ornamental designs as per the site condition and as directed by the departmental officers.

Fabricating supplying and fixing of 8mm thick Calcium Silicate Board Designed and Perforated for False Ceiling

Fabricating supplying and fixing of roof with Poly carbonate sheet of 6mm thcik with any colour or any other approved design and to be fixed with shelf tapping screws, plastic washer. The washer and screws to be fixed by using minute power machine drilled with out damaging the sheets. The sheet to be fixed with making suitable corrugated, cutting the sheet in to the required ssize and making ornamental designs as per the site condition and as directed by the departmental officers.

Supplying and fixing G.I. Gutter made of 20 B.W.G. galvanised iron sheets and G.I. valleys made of 18 B.W.G. galvanised iron sheets including fixing,etc.,complete.(ISI STD)

Supplying, fabricating, erecting structural steel work for roofing welded or bolted type using MS channels, angles, plates and round bars etc. conforming to IS specification including primer coating as per Design given by the departmental officers etc, complete as per standard specification

Providing and painting all steelwork with (i) one primer coat of inorganic zinc silicate (min. Vs 62%) 50 micron (ii) one coat of epoxy HB MIO brown (min Vs 55%) 75 micron (iii) one coat of polyurethane paint (min. Vs. 40%) 40 microns including all material,one coat of epoxy HB paint (min. Vs 60%) 100 microns (iv) labour, scaffolding etc. The surface shall be shot blast to SA 2.5 standard using grit. The paint shall be applied as manufacturer's specifications and the item shall include necessary testing, test certificate etc.

Providing, assembling and Supplying of Double Glazed Performance glass, heat Strengthened clear Glass (IGUs) of size and shape as required and specified of approved, comprising of an outer heat strengthened clear glass of following thick of approved colour and shade with reflective soft coating on surface #2 and an inner heat strengthened clear glass of following thick , spacer tube 12mm wide , dessicants, including primary seal and secondary seal ( structural silicon sealant ) etc. all complete for the required performance , as directed by the engineer -in - charge. The heat strengthened clear glass having properties as visible Light transmittance (VLT) of 25 to 35 %, Solar heat gain coefficient less than or equal to 0.27 and U value of 3.0 to 3.3 W/m2 or lower degree K etc. The IGUs shall be assembled in the factory/ workshop of the glass processor. For payment, only the actual area of glass on face # 1 of the glass panels (excluding the areas of the grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm. 8mm+12mm+6mm

FRAME WORK FOR STRUCTURAL GLAZING: Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of structural glazing (with open joints) for linear as well as curvilinear portions of the building for all heights and all levels, including: (a) Structural analysis & design and preparation of shop drawings for the specified design loads conforming to IS 875 part III (the system must passed the proof test at 1.5 times design wind pressure without any failure), including functional design of the aluminum sections for fixing glazing panels of various thicknesses, aluminium cleats, sleeves and splice plates etc. gaskets, screws, toggles, nuts, bolts, clamps etc., structural and weather silicone sealants, flashings, fire stop (barrier)- cum-smoke seals, microwave cured EPDM gaskets for water tightness, pressure equalisation & drainage and protection against fire hazard including: (b) Fabricating and supplying serrated M.S. hot dip galvanised / Aluminium alloy of 6005 T5 brackets of required sizes, sections and profiles etc. to accommodate 3 Dimentional movement for achieving perfect verticality and fixing structural glazing system rigidly to the RCC/ masonry/structural steel framework of building structure using stainless steel anchor fasteners/ bolts, nylon seperator to prevent bimetallic contacts with nuts and washers etc. of stainless steel grade 316, of the required capacity and in required numbers (c) Providing and filling, two part pump filled, structural silicone sealant and one part weather silicone sealant compatible with the structural silicone sealant of required bite size in a clean and controlled factory / work shop environment, including double sided spacer tape, setting blocks and backer rod, all of approved grade, brand and manufacture, as per the approved sealant design, within and all around the perimeter for holding glass....... d) Providing and fixing in position flashings of solid aluminium sheet 1 mm thick and of sizes, shapes and profiles, as required as per the site conditions, to seal the gap between the building structure and all its interfaces with curtain glazing to make it watertight. (e) Making provision for drainage of moisture/ water that enters the curtain glazing system to make it watertight, by incorporating principles of pressure equalization, providing suitable gutter profiles at bottom (if required), making necessary holes of required sizes and of required numbers etc. complete. This item includes cost of all inputs of designing, labour for fabricating and installation of aluminium grid, installation of glazed units, T&P, scaffolding and other incidental charges including wastages etc., enabling temporary structures and services, cranes or cradles etc. as described above and as specified. The item includes the cost of getting all the structural and functional design including shop drawings checked by a structural designer, dully approved by Engineer-incharge. The item also includes the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working structural glazing as specified, cleaning and protection till the handing over of the building for occupation. In the end, the Contractor shall provide a water tight structural glazing having all the performance characteristics etc. all complete as required, as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer- in-Charge.

Supply and fixing of M.S Grills with Doors and Windows with one coat of Red oxide with Primer including all costs such as welding,grinding and fabrication charges, cost and conveyance of all materials to site etc,complete as per standard specification.

Supplying and Fixing English Stainless Steel Letters 25cm (10”) Providing and fixing of Stainless steel grade 304 golden letters in English with Main letter of minimize size 175 mm with 25 mm raising. The rest of letters shall also be of Stainless steel grade 304 in golden with minimum size of 150 mm, 25mm raising. The letters shall be fixed with the help of stainless steel studs on existing granite wall which shall not be visible from the front. The stainless-steel studs shall be properly grouted with suitable sealant. The logo shall be of minimum dia 750 mm and shall be perforated one with cutting of balance vacant space leaving the matter in logo. The letters of name in logo shall be engraved/etched in black letters over golden stainlesssteel sheet with heating process. The work shall be executed to the satisfaction of Engineer- in-charge.

Supply and Installation of Anutone Strand Nubby, square edge, magnesite-bonded,2mm wide pinewood fibre core,fully encapsulated with texture finish,Green Pro certified ceiling tile of size 595x595x15mm thk having volume density 400Kgs/m3, weight 6kg/m2 suspended using 0.3mm thick Anutone Skelet Trelis T15 metal grid system.Anutone Skelet Trelis T15 ceiling grid system, of 600x600mm module includes Anutone Skelet WA15W30 with unequal flanges of 15/19mm, length 3000mm, fixed along the perimeter of walls with the help of nylon sleeves and suitable fasteners at 300mm centres.Then suspend the Anutone Skelet MT15W36 with flange width 15mm, height 32mm and length 3600mm, from the soffit slab with help of Anchor Bolt, Soffit Cleat and Suspension Rod with Levelling Clip at 1200mm centres. Anutone Skelet CT15W12 with flange width 15mm, height 26mm and length 1200mm is interlocked into the pre-cut slots in the Main T15 at 600mm centres in the perpendicular direction to the Main T15. Finally Anutone Skelet CT15W06 with flange width 15mm, height 26mm and length 600mm are interlocked into the precut slots in the CT15W12 in direction parallel to the Main T15 to result in 600x600mm module. Anutone Strand Nubby panels of size 595x595x15mm thk shall be placed into the grid size of 600x600mm. Ensure arrow marks behind the tiles are oriented in one direction to achieve uniform shade. Technical Parameters Fire (Class) – 1 & P Acoustics – NRC upto 0.9 (For E600 Mounting) Thermal conductivity (W/mk)– 0.07 Climate (°C, RH) – 50, 95 Light reflectance (%) – 85 Green (VoC, RC %) – Low, 30

Supply & installation of Anutone Spots MP3 Lite,made of pinewood E1 grade fiberboard, with 3mm circular perforations @ 16mm c/c, melamine/veneer laminated finish, 1-test FR grade, size 600x1200x16mm, Conceil-A edge, volume density of base board 700Kg/m3, weight of base board 11.2Kgs/m2 suspended using 0.3mm thick Anutone Skelet Trelis T24 metal grid system. Anutone Skelet TrelisT24 framework system includes Anutone Skelet WA24W30,sectional thickness 0.4mm, wall angle with equal flanges of 24mm, length 3000mm, fixed along the perimeter of walls with the help of nylon sleeves and suitable fasteners at 300mm centers. Then suspend the Anutone Skelet MT24W36, sectional thickness 0.3mm, with flange width 24mm, height 38mm and length 3600mm, from the soffit slab with help of soffit cleat and wire rod with leveling clip at 590mm centres. Anutone Strut M6 threaded rod is then positioned in the slots on top of web of Main T24 at 1200mm centers in staggered pattern to hold system in position. M6 threaded rods to be secured in place with M6 hexagonal nuts. Anutone Spots MP3 Lite, ConceilA edge, of size 600x1200x16mm shall then be slided onto Main T24 such that short edges are staggered. The system is backlined with acoustical infill Anutone SynthPF 5x50.Technical Parameters Fire (Class) – 1 & P Acoustics – NRC Upto 0.75•Climate (°C, RH) – 50, 70 Light (%) – Colour Dependant Green (VoC, RC %) – E1, 25

Supply and installation of Anutone Subtex Clouds Nubby Melange Circle/ Hexagon,of size 600 dia,30mm thk, which are having glassfibre core,colour textured finish and are fully encapsulated Panels are having volume density 120kgs/m3 and weight 3.6kg/m2. Each Cloud is provided with 4 sets of accessories containing Corkscrew, levelling hook and hanger wires. Corkscrew to be rotated and anchored at back of each panel at four points to hold the panel stable. Supplied hanger wires to be first dropped from the beam/slab/truss to desired height with suitable anchor bolts and S hook. Anutone Subtex Clouds Nubby Melange Circle/Hexagon are then suspended using spring hooks and hanger wires and levelled into position with levelling clips. (Anchor bolts and S hook not by Anutone). Fire (Class) – 1 & P Acoustics – NRC 0.7 (For J Mounting Thermal conductivity (W/mk)– 0.07 Climate (°C, RH) – 40, 95 Light reflectance (%) –Colour dependant Green (VoC, RC %) – Low, 35

Supply & installation of Anutone Salon Slats Surco made of pinewood E1 grade fiberboard, melamine laminated finish, groove perforated slats L16-2 - (2mm grooves @16mm pitch with 7.3 % open area), backlined with Soundtexblack acoustical fleece of 0.27mm thick, surface density 63g/m2,rear scoring with perf 10mm at 20mm pitch, tongue-groove edge for a seamless look, flame resistant (BS476 part 7) , of size 128 x2440x16mm, volume density of base board 700Kg/m3, weight 11Kg/m2 (L16), installed by using GI Strut framework system.The GI Strut framework system shall include Strut CC25 fully knurled, sectional thickness 0.55mm, length 3600mm, web 50mm, depth of 25mm and equal flanges 15mm is fastened to the wall positioned horizontally or vertically at every 600mm centres.Anutone Strut CC18,aluminium core cross channel, thickness 0.5mm, length 2400mm, web 15mm & 27mm, depth 18mm and flanges of 7mm with suitable edge & center brackets is then fixed perpendicular to the Strut CC25with the help of fasteners at every 400mm centers Anutone Slats Surco lite of size 128x 2440x16mm in then fixed perpendicular to Strut CC18 with suitable edge & centre brackets. The system is backlined with Anutone SynthPF 5x25 adhered on wall with dab spots of Anutone stick S7 adhesive. Technical Parameters Fire (Class) – BS476 part 7 , Acoustics – NRC 0.75, Thermal conductivity (W/mk)– na, Climate (°C, RH) – 50, 70, Light reflectance (%) – 75 (Maple Arce),Green (VOC, RC %) – E1, 25

"Supply and Installation of Anutone Mat , Square edge, anti-bacterial,magnesite-bonded pinewood microparticle core Factory finished tiles ,GreenPro certified,of size 595x595x15mm thk, volume density 600kgs/m3, weight 9kg/m2 Suspended using 0.3mm thick Anutone Skelet Trelis T24 metal grid system. Anutone Skelet Trelis T24 ceiling grid system, of 600x600mm module includes Anutone Skelet WA24W30 wall angle with equal flanges of 24mm, length 3000mm,0.4mm thk, fixed along the perimeter of walls with the help of nylon sleeves and suitable fasteners at 300mm centres. Then suspend the Anutone Skelet MT24W36 MainT with flange width 24mm, height 38mm and length 3600mm, from the soffit slab with help of anchor bolt, soffit cleat and wire rod with leveling clip at 1200mm centres. Anutone Skelet CT24W12 CrossT with flange width 24mm, height 32mm and length 1200mm is interlocked into the pre-cut slots in the Main T24 at 600mm centers in the perpendicular direction to the Main T24. Finally Anutone Skelet CT24W06 CrossT with flange width 24mm, height 32mm and length 600mm are interlocked into the pre-cut slots in the CT24W12 CrossT in direction parallel to the Main T24 to result in 600x600mm module. Anutone MAT H+ ,square edge, of size 595x595x15mm shall be placed into the grid size of 600x600mm. Technical Parameters Fire (Class) – 1 & P Acoustics – NRC 0.9 (For E300* Mounting) Thermal (W/mk)– 0.1 Climate (°C, RH) – 50, 95 Light (%) – 80% Green (VoC, RC %) – Low, 35

Supply and installation of Anutone stretch NRC Fabric system by using NRC FR Grade fabric of size 1700mm width, shall be stretched by using CC 25 with infill of synth pf 5X25 mm thick, rigid vinyl Stretch Tracks half wrap/full wrap 15mm (FS15) and Midseam 15mm (FS15), strand board, synth PF infill with requisite accessories & tools. CC 25 mm is first installed on the wall along with ithe marking lines with metal fasteners inserted at 300mm centers .Strand 3 Primer square edge magnesite bonded pinewood fiber panels of size 600x1200x20 mm having density 400kg/m3, weight 4kg which is fixed to CC25 cross Channel with suitable fasteners. 12mm Wooden reppers screw fixed on strand as per design patterns. FS15 tracks to be installed on wooden base, after applying Stick S7 adhesive on both surfaces for a true and continuous secure grip, and heavy-duty fasteners at 150mm centers on one/both sides of Stretch Tracks .Synth PF 5x25mm thick adhered on strand panel by using Stick 7 adhesive. Fabric ofwidth 1700mm is then aligned to the Stretch tracks by following the fabric thread lineor pattern. The fabric is stretched and tucked into the Stretch tracks and secure into the locking jaws so that it will be smooth, free of wrinkles with the tucking tools. Note minimum 50mm additional fabric is required for tucking hence maximum module wallfabric width would be 1600mm. Technical parameters : Core - pinewoodfibre & polyfibre, Fire – 1, Acoustics – NRC 0.90, Climate (OC RH) – 49, 90, Termiteresistance – Yes, Light reflectance – Colour dependent, Green (RC %) – 25, Hygiene (VoC, Clean room) – Low, Class 1 As per the drawings and as directed by the Engineer-in-Charge/ Consultant

Supply and installation of 70mm thick Tufbloc magnesia drywall partition system (having high water & fire resistance) which includes one layer of Anutone Tufbloc Square edge of size 1200x2400x12mm having density 1000kgs/m3, weight 12kg/m2 fixed on the either side of GI strut channel framework. Framework includes Floor/ Head (FC50) GI channels having thickness 0.55mm, length 3600mm, equal flanges of 32mm and web of 50mm fixed to floor and ceiling with suitable fasteners at 300mm centers staggered. Noise and fire rated silicon sealant to be caulked along the perimeter of the partition frame before fixing channels. Then Stud channel (SC48) having thickness 0.45mm, length 3600mm, unequal flanges of 34/36mm and web of 48mm should be placed into the floor/head channel positioned vertically at 600mm centers. Extra reinforcement to be provided at openings (doors, windows, etc.,) Anutone Synth PF having thickness 50mm, width 600mm, density 1000gsm filled between the Studs and held in position by using chicken wire mesh/cross bracings/pasting on one side of the boards. The first layer of Anutone Tufbloc 12mm thick should be fixed on one side of the Stud framework in a staggered pattern by using suitable metal fasteners at 300mm centers. Second layer of Anutone Tufbloc 12mm thick should be fixed other side of the framework similar fashion as the first layer. 4mm gap should be maintained between boards on all sides. 4mm gap to be filled in fully to depth of board by using Anutone Seam kit as per given recommendations. Technical Parameters Core - Magnesia Fire Rating – upto 150 mins Acoustics – STC upto 50 Climate (OC RH) – 50, 99 Termite resistance – Yes Moisture Absorption - 6.8% after 2hrs and 11.3% after 24hrs soaking Wet Expansion - < 0.02% from ambient to saturation Dry Contraction - ≤ 0.02% from evaporation Moisture Movement - 0.02% Light reflectance – 80% Green (RC %) – 30 Hygiene (VoC, Clean room) – Low, Class 1 Strength - Antisag Impact - 4kg hammer 175mm

FALSE CEILING WITH GYPSUM BOARD Providing and fixing suspended false ceiling using SAINT - GOBAIN GYPROC or Equivalent make which includes providing and fixing GI perimeter channel of size 0.50mm thick having one flange of 20mm and another flange of 30mm and a web of 27mm along with perimeter of ceiling, screw fixed to brickwall / partition with the help of nylon sleeved and screws at 610mm centres. Then suspending GI intermediate channels of size 45mm, 0.9mm thick with two flange of 15mm each from the sofit at 1220mm centres with ceiling angle of width 25mm x 10mm X 0.55mm thick fixed to sofit with GI cleat and steel expansion fasteners. ceiling section 0.55mm thickness having knurled web of 51.5mm and two flanges of 26mm each with lops of 10.5mm are then fixed to the intermediate channel with the help of connecting clips and in direction perpendicular to the intermediate channel at 610mm centres. 12.5mm Gypboard is

Providing and fixing 50mm thick GFRC (Glass Fiber Reinforced Concrete) Jalli with approved color and design; fabricated using type i or ii cement, sand in 1:1 ratio, and chopped ar glass fibers (2–3% by weight for premixed gfrc or 4–6% for spray-up gfrc); acrylic polymer emulsion with 5% acrylic solids by weight of cement; vcas pozzolan to replace 10–25% of the cement; addition of superplasticizer, water reducer, or polymer-curing admixture as required; color to be integrated in the face coat using dry or liquid pigments; panels to be factory-made with controlled curing for consistent quality; rate inclusive of all supports, stainless steel anchors and hardware, grouting, expansion joints with weather-resistant silicone sealant, crane and hoisting charges, scaffolding, and specialized labor; application of two coats of approved acrylic sealer; sealing of cracks and chips due to handling or construction; final cleaning and finishing complete

Supplying and fixing Partition with powder coated Aluminium frames with Bottom Double glass with centre rattan cane and top fluted glass including cost of Material, Labour, lead etc., Complete.

Providing & fixing in position Wall and Column Panelling 18 mm thick WPC Board finished with 1 mm thick laminate with approve colour as per direction of the Architect.

Providing & fixing in position 5mm thick fluted glass panels including cost of Material, Labour, lead etc., Complete.

Providing & fixing in position 5mm thick Tinted glass panels including cost of Material, Labour, lead etc., Complete.

Providing & fixing in position 5mm thick Lacker Glass panels including cost of Material, Labour, lead etc., Complete.

Providing Cup-board Shutter with frame using termite / water proof plywood of 19mm thick over which laminated sheet of 0.8mm thick fixed inside the shutter and 1mm thick fixed in the outside of the shutter using fevicol along with necessary furniture fittings, such as, hydralic hinges, tower bolt, handles, multi purpose locks etc., as directed by the Departmental Officers. The design pattern, water proof plywood, laminate sheet and other materials should be got approved from the Executive Engineer befoe use on work.

Providing and fixing Acoustic Wall Panelling (equivalent to Armstrong) in channelled wood works perforated panels of width 192mm, thickness of 15mm and length of 2400mm or as per required by the Departmental Engineer made of a high density fibre board with minimum 725 kg./m3 density substrate with a laminated facing as per the approved shade and finish and a melamine balancing layer on the reverse side. The boards shall have a special peforation pattern where the visible surface has a “Helmholtz” fluted perforation of 3mm width and 21mm of visible panel each. The edges of the panels shall be “tongue-and-grooved” to receive special clips for installation. The back of the perforated panel shall have sound absorbing non woven acoustical fleese having NRC of 0.52. The panels shall be mounted on special aluminium splines using clips provided by Armstrong and approved by the Engineer-in-Charge. Installation: Install aluminium box section (provided by others) of section 50mm x 25mm or as approved by the Engineer-in-Charge on the solid wall horizontally using screws and plugs at spacing of 600mm centre to centre. Screw the aluminium extruded keel for channelled wood works provided by Armstrong over the lowest and second aluminium section at an on centre distance of 600mm. Place the inside clip on the groove end of the panel along the aluminium keel and then place the tongue end of the next panel. Continue installing rows of panels by inserting the tongue into groove of the earlier inserted panel and progressively installing inside clips into the next keel till the actual height is achieved. Finish off the edges using wooden moulding of matching colour (provided by others). Installation to be carried out by Armstrong Trained Installation Team and installation should be carried out as per Armstrong Recommended Procedure.

Supplying and Fixing Aluminium Profile for flooring

Supplying and Fixing Aluminium Profile for Wall

The supply and installation of a welded metal mesh fence with a mesh opening size of 50mm x 200mm, fabricated in panel dimensions of 1560mm (h) x 2500mm (l). The panels shall be securely fixed to supporting posts of 1600mm length, spaced at 2560mm center-to-center (c/c). The posts shall be anchored to the ground using M12 anchor bolts of 150mm length, ensuring stability and structural integrity. All materials used shall be corrosion-resistant and conform to relevant industry standards for durability and longevity.

Providing & fixing PVC RAIN WATER DOWNFALL PIPE of the following dia with necessary T.W.Clamps Plugs, Shoes,Bemds, other clamps, screws nails etc.,complete complying with standard specification. The rate is inclusive of cost of removable iron gratings of appropriate size. The size of Teak Wood plugs used is 150X25mm in front & 200x75mm in rear (wall side) with a depth of 110mm. The pipe is to be fixed by means of "U" clamps at the centre of pipes to be fixed.110mm dia PVC Pipe [4 Kg/SqCm]

Supply and providing Priming Tank made up of PVC. Make: SINTEX / EQUIVALENT

Supplying and fixing in position best quality P.V.C soil/ waste pipes (6KSC) of various sizes having ISI mark and providing leakproof joints including fixing to the wall with P.V.C/ M.S clamps etc., and making connection to all sanitary fittings, dismandling masonry/R.C.C. works wherever necessary and making good the dismandled portion to the original condition, complying with standard specifications.

75mm dia

110mm dia

160mm dia

50mm dia

Internal Water Supply - CP.V.C. Pipes (6Kg/SqCm) Supplying laying and jointing P.V.C pipes (6Kg/SqCm) of approved quality and best variety conforming to I.S.S & with I.S.I mark, of the following sizes including cutting , Fixing to PVC specials using Adhesive but excluding cost of such specials and fixing to wall with necessary teak - Wood Plugs,PVC Clamps and screws,making holes on the wall or drilling holes in roof and making good the dismantled portions to original condition with necessary brick work and plastering wherever necessary with necessary scaffolding charges.

15mm dia

20mm dia

25mm dia

32mm dia

Supplying and fixing in position best quality approved make white glazed earthenware Oval Shape Wash Hand Basin of size 560 x 450mm with a pair of cast iron brackets, including cost of 15mm diametre brass chromium plated piller tape,32 mm diametre C.P. Waste union, 32 mm diametre P.V.C. waste pipe with rubber plug and chain, 15mm diametre G.M.wheel valve, 15mm dia brass nipple, 15mm dia nylon connections etc., including fixing the wash hand basin in the wall in position with a pair of C.I. brackets with teak wood plugs and screws and giving necessary water supply connection and paintiung the brackets with two coats of paint over a primimg coat of anticorrosive paint including testing for leackage etc., complete complying with standard specifications

Supplying and fixing in position indian make bewelled edge mirror of approved quality and brand of size 600 X 450mm wth necessary plastic back, PVC frame with bottom stand of approved colour with brass screws,rawal plugs etc., complete complying with standard specifications

Supplying and fixing best approved quality C.P.Soap Tray of size 150mm X 100mm including cost of Teak Woodplugs, brass screws complete complying with standard specifications.

Supplying and fixing best approved quality Brass C.P / Al anodised Towel rail 600mm. long and 20mm Diameter with brackets of same material including cost of Teak-Wood plugs and C.P.Screws etc., complete complying with standard specifications

Suppling and fixing in position 15mm diameter brass / C.P screw down tap / pillar tap / swan neck tap (heavy duty) of approved make conforming to I.S.specifications and quality including cost of shellac, thread etc.complying with standard specifications and including cutting and threading wherever necessary. C.P screw down tap

Supplying and fixing in position White / Colour Glazed Model Floor Mounted European Water Closet of best quality and approved make with 100mm “P” or “S” trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 liters capacity PVC / 12.5 liters capacity porcelain low level flushing tank with a pair of CI brackets, etc., complete with all fittings, such as, 15mm brass ball valve with polythene float with brass handle, union coupling connected by means of 40mm white PVC flush hand using Indian adopter joint including all internal fittings, such as, 15mm bras connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition, etc., complete complying with standard specifications. (The EWC and flushing tank with all accessories should be got approved by the Executive Engineer before use on works) Floor Fitting

Supplying and fixing the best quality approved make of bip cock with C.P. health faucet wall hook one metre long flexible tube, angle cock with wall flange including cutting and making good the walls wherever required etc.complete, complying with standard specification and as directed by the Department officers. The quality and make of health faucet should be got approved by Executive Engineer before use on work.

Supplying and fixing of White Glazed Porcelain Oval Shape Special Type Urinal of size 382 x 398 x 601mmwith all accessories such as 32mm dia Bell Mouth PVC Connection, 15mm dia GM Wheel Value, 15mm dia ‘B’ Class GI Waste Water Pipe, 15mm dia Nylon Connection, 15mm dia Brass Nipple etc.

Supplying & fixing in position PVC Nahini / Floor trap of size 100x75mm including stainless steel gratings of approved brand & quality, fixed over a bed of brick jelly lime concrete 1:2:5 ( One part of lime, two parts of sand & five parts of 40 mm size brick jelly ) & finished with cement mortar 1:3 ( One cement & three sand ) including dismantling masonry works wherever found necessary & making good the damaged portions to the original condition & giving connections to the cast iron pipes etc., complete, complying with standard specification. (The PVC Nahini / Floor trap should be got approved by the Executive Engineer before use on works ).

Making through holes in Plain or Reinforced Cement Concrete with Diamond Core Drilling System by using BOSCH power tools of following diamete - Depth per cm

Supplying & fixing in position first quality & approved variety of 50mm dia C.P.V.C Ball Valves ( Heavy type ) with I.S.I. Mark of the following size including cost of Shellac, thread etc.,including labour for cutting & threading of Pipes etc., complete complying with standard specifications for both internal & external water supply arrangements.

25mm dia

32mm dia

Drilling of 12" dia vertical borewell so as to have a finished size of 6" dia borewell in boulder area to any required depth as decided by the TWAD Board Officers including Transportation from one place to anothr place with in Tamilnadu State by direct or reverse rotary mud circulation method using Contractor's rig tools, fuel, labourers, bentonite mud and water required for drilling at the site shown by the TWAD Officers including construction of mud pit etc. using only calyx rigs.

Drilling of Borewells anywhere in Tamilnadu including transportation from one place to another with in Tamilnadu in alluvial soil sedimentary strata of clay and sand stone shale pebbles boulders etc. By first taking a pilot bore of 140 mm/150mm dia and then enlarging to required dia direct or reverse rotary mud circulation method using rotary rigs, fuel, labour and drilling bentonite and water required for drilling at site ( Site will be shown by the TWAD Board Officers) including construction of mud pit

Drilling of 140/150 mm pilot bore - Upto 60 m Depth ending below ground level

Drilling of 140/150 mm pilot bore - From 60 m upto 90 m Depth ending from ground level

Drilling of 140/150 mm pilot bore - From 90 m upto 120 m Depth ending from ground level

Reaming 300 mm dia pilot bore to 400mm/ 450mm dia bore as directed by the TWAD Board Officer.

Upto 60 m depth ending below ground level

Reaming 140/150 mm dia pilot bore to 300mm dia bore as directed by the TWAD Board Officer.

Upto 60 m depth ending below ground level

From 60 m depth and upto 90 mt depth ending below ground level

From 90 m upto 120 mt depth ending below ground level

Supply and laying following dia PVC casing pipe with excise duty as per IS 12818 / 1992

200mm dia CS

150mm dia RS

Labour charges for inserting PVC casing pipes assembly (with slots or without slots) in the drilled hole including jointing the pipes with PVC couplers with cement paste etc., complete, supply and packing the annular space with pebbles of size and quality as approved by the Executive Engineer of Departmental officers.

200mm dia CS

150mm dia RS

Supplying and filling with river pebbles in annular space between bore and PVC pipe up to hard rock.

Charges for developing the borewell with air compressor of 300 CFM capacity (Minimum 8 Hours) including transportation labour and fuel charges for compressor as directed by TWAD Board Officers and conducting yield test by 'V' notch method.

Supply ,erection and testing & commisioning of 3HP submersible pumpset in the to suit 200mm borewell of capacity of 4800 LPH @ 265Ft, max. total head of 280 Ft pumps fitted with bronze impellers and having delivery size of 40mm - 430V along with 3mts cable and manufactures standard control panel which is mandatory and as directed by the officer incharge and other required supporting items like SS hose nipple, nylon rope, clamps, bolt and nuts,GI nipple, 50mm dia HDPE hose of required length etc completed and as directed by the officer incharge.

Supplyinga dn fixing 5.0 HP Monoblock Pump including all accessories

Supplying and Fixing Liquid Soap dispenser - Parryware- T6513A1 or Equivalent

Supplying and fixing PARTITION MOUNTED SANITARY NAPKIN DISPOSAL Color: Silver Installation Partition-mounted Operation Manual Finish :Satin Shape: Rectangle Capacity 4.7 Liter. Product Dim. L 330 x W 107 x H 505 mm

Supplying and fixing Flash touch-free infrared hand dryer with 1150W rated power & carbon brush motor. Jaquar - HDR-SSF-AK2807 or Equivalent

Supplying and fixing Paper holder with flap recessed type (Stainless Steel) Jaquar AHS-1553 or Equivalent

Supplying and Fixing recessed type manhole cover

600mm x 600mm

750mm x 750mm

900mm x 900mm

Supply and fixing of 3D Wooden worl map with the following Specifications. Sie- 2x 1.20M, Oreientation:Landscape, Material: Crafted from high quality birch plywood

Supply and fixing of Sheesham Wood Arm Chair In Rustic Teak Finish with the following Dimensions (In Centimeters) H 77 x W 53 x D 58

Supply and fixing Sheesham Wood Bar Chair in provinical Teak Finish with the following Dimension:H 109.2 X W 43.X D 58.4.

Supply and fixing of 3 saeter Southampton Rattan Leather Sofa with the following Specifications. Dimensiomns: 3 Seater: 195cm W x 86cm D x 87cm H, Composed of Solid Hardwood, Comes with a fixed seat and loose back pillow.

Supply and fixing of Rattan Sofa solid wood with the following specifications. Dimensions: Length:- 75 inches x Width:- 33 inches x Height:- 30 inches, Material – Solid Mango wood and natural cane weaving, Fabric – 100% cotton canvas with Leather pillows, Pillow – 2 Pillows Included, Rattan work on 3 sides of the sofa

Supply and fixing Tot Cubby Fabric kids chair in Beige Colour with the following Specifications. Dimensions: H 20 X W 20 X D 46, Primary Material: Fabric.

Suuply and fixing of Nico fabric pouffe in yellow colour with the following Specifications. Dimensions: H41 X W 39 X D 39, Primary Material: Fabric.

Suuply and fixing of Aston Fabric Pouffe In Beige Colour Set Of 4 with the following Specifications. Dimensions (In Centimeters) H 41 x W 94 x D 94, Primary Material: Fabric

Suuply and fixing of LOCCUS 6 Seater Patio Furniture Dining Set, Wooden Dining Table and Rope Chairs Set, Conversation Set Outdoor Dining Set for Garden, Balcony, Poolside, Backyard, (Light Grey Wicker).dimensions L x W x H 132.1 x 96.5 x 73.7 Centimeters

SINGLE STUDY CHAIR: Supplying and Placing Single Study Chair with Full writing pad high density fibre board, Seat and Backrest: Specially blended glass filled nylon, 22mm dia M.S Taubular understructure, Bottom Bock rack, Powder Coated Finish

WHITE ROLLING CHAIRS - Supplying & placing of Mesh chair of Medium Mesh Back Chair, Cushioned Seat, Adjustable Lumbar Support, Gaslift, Synchro Mechanism, Adjustable Arms, Nylon Base. The rate should include Materials lead and lift, cleaning , etc.

RECEPTION DESK - 1600mm x 600mm x 750mm - Supply and fixing of Reception Desk of 40mm consists 2 Nos of 19mm BWR Plywood clad with 4mm thick teak veneer crown cut PU polish satin matte finish and partition consists of 20mm Half round wooden beeding PU satin Matte fixed to 19mm BWR plywood finished with veneer on the one side and top of partition 2 Nos 19mm BWR Plywood clad with teak veneer crown cut PU polish satin matte with approved finish. Flip up wire manager is provided on top. . The table have storage of size - 800mm x 600mm with shutters . Complete with all hardwares of ebco/hettich make or similar. etc. The rate should included debris clearing, Materials lead and lift, cleaning , etc. complete as per drawing.

OFFICE TABLE - 1555mm x 600mm x 750mm - Supply and fixing of Table top of 40mm consists 2 Nos of 19mm BWR Plywood clad with 4mm thick teak veneer crown cut PU polish satin matte finish. Supported on 19mm BWR plywood clad with 2mm thick HDF duco paint to approved shade finish Flip up wire manager is provided on top. . The table will have one number of drawer and 1 No of storage shutter of size - 402mm x 600mm x 590mm with lockable drawers . Complete with all hardwares of ebco/hettich make or similar. etc. The rate should included debris clearing, Materials lead and lift, cleaning , etc. complete as per drawing.

Supply and fixing of Swivel chair with soft shapes and nice padding with the following Specifications: Tested for: 110 kg (243 lb), Width: 67 cm (26 3/8 "), Depth: 67 cm (26 3/8 "), Seat width: 44 cm (17 3/8 "), Seat depth: 40 cm (15 3/4 "), Min. seat height: 45 cm (17 3/4 "), Max. seat height: 57 cm (22 1/2 ")

Supply and fixing of Sofa Set With Tea Table (2 seater sofa + 2 seater sofa + 2 seater table ) with the following specifications. Fabric :- Sweat Velvet , Material :- MS Powder Coated Rust Free, 48" x 22" x 30" - Sofa, 20" x 18" x 32" - chair,

Supply and fixing of Zenora Rattan Coffee Table with the following specifications. Dimensions in inches: 43.3 x 23.6 x 15.7

6 SEATER LEARNING CENTRE TABLE - 3000mm x 900mm x 750mm - Supply and fixing of Rectangular Table top of 40mm consists 2 Nos of 19mm BWR Plywood clad with 4mm thick teak veneer crown cut PU polish satin matte finish. 2700mm x 900mm length of table top is Supported on legs 50mm dia MS Hollow Section powdered coated to approved shade with 4mm bush at the bottom. Supported Legs are in the four corners & inbetween. For Legs Horizontal Support 75mm x25mm MS Hollow Section powdered coated to approved shade, Flip up wire manager is provided on top. Complete with all hardwares of ebco/hettich make or similar. etc. The rate should included debris clearing, Materials lead and lift, cleaning , etc. complete as per drawing. Refer Detail No:2

8 SEATER LEARNING CENTRE TABLE - 3900mm x 1200mm x 750mm - Supply and fixing of Rectangular Table top of 40mm consists 2 Nos of 19mm BWR Plywood clad with 4mm thick teak veneer crown cut PU polish satin matte finish. 3600mm x 1200mm length of table top is Supported on legs 50mm dia MS Hollow Section powdered coated to approved shade with 4mm bush at the bottom. Supported Legs are in the four corners & inbetween. For Legs Horizontal Support 75mm x25mm MS Hollow Section powdered coated to approved shade, Flip up wire manager is provided on top. Complete with all hardwares of ebco/hettich make or similar. etc. The rate should included debris clearing, Materials lead and lift, cleaning , etc. complete as per drawing.

10 SEATER LEARNING CENTRE TABLE - 4900mm x 1200mm x 750mm - Supply and fixing of Rectangular Table top of 40mm consists 2 Nos of 19mm BWR Plywood clad with 4mm thick teak veneer crown cut PU polish satin matte finish. 3600mm x 1200mm length of table top is Supported on legs 50mm dia MS Hollow Section powdered coated to approved shade with 4mm bush at the bottom. Supported Legs are in the four corners & inbetween. For Legs Horizontal Support 75mm x25mm MS Hollow Section powdered coated to approved shade, Flip up wire manager is provided on top. Complete with all hardwares of ebco/hettich make or similar. etc. The rate should included debris clearing, Materials lead and lift, cleaning , etc. complete as per drawing.

12 SEATER LEARNING CENTRE TABLE - 5200mm x 1200mm x 750mm - Supply and fixing of Rectangular Table top of 40mm consists 2 Nos of 19mm BWR Plywood clad with 4mm thick teak veneer crown cut PU polish satin matte finish. 3600mm x 1200mm length of table top is Supported on legs 50mm dia MS Hollow Section powdered coated to approved shade with 4mm bush at the bottom. Supported Legs are in the four corners & inbetween. For Legs Horizontal Support 75mm x25mm MS Hollow Section powdered coated to approved shade, Flip up wire manager is provided on top. Complete with all hardwares of ebco/hettich make or similar. etc. The rate should included debris clearing, Materials lead and lift, cleaning , etc. complete as per drawing.

CHILDRENS 6 SEATER LEARNING CENTRE TABLE - 1500mm x 4500mm x 450mm - Supply and fixing of Rectangular Table top of 40mm consists 2 Nos of 19mm BWR Plywood clad with 4mm thick teak veneer crown cut PU polish satin matte finish. 3600mm x 1200mm length of table top is Supported on legs 50mm dia MS Hollow Section powdered coated to approved shade with 4mm bush at the bottom. Supported Legs are in the four corners & inbetween. For Legs Horizontal Support 75mm x25mm MS Hollow Section powdered coated to approved shade, Flip up wire manager is provided on top. Complete with all hardwares of ebco/hettich make or similar. etc. The rate should included debris clearing, Materials lead and lift, cleaning , etc. complete as per drawing.

INDIVIDUAL SEATER LEARNING TABLE - 800mm x 600mm x 750mm - Supply and fixing of Rectangular Table top of 40mm consists 2 Nos of 19mm BWR Plywood clad with 4mm thick teak veneer crown cut PU polish satin matte finish. 3600mm x 1200mm length of table top is Supported on legs 50mm dia MS Hollow Section powdered coated to approved shade with 4mm bush at the bottom. Supported Legs are in the four corners & inbetween. For Legs Horizontal Support 75mm x25mm MS Hollow Section powdered coated to approved shade, Flip up wire manager is provided on top. Complete with all hardwares of ebco/hettich make or similar. etc. The rate should included debris clearing, Materials lead and lift, cleaning , etc. complete as per drawing.

BOOK RACK - Supply and placing of book rack features a combination of CRCA steel as the primary material and particle board as the secondary material, ensuring durability and a modern aesthetic. With dimensions ranging from 3600 X 600X 2100mm. The product should be GreenGuard certified or Godrej or similar make.

LOCKER & FOOTWEAR STORAGE - 4152mm x 300mm x 900mm - Supply and fixing of L Shape Locker & Footwear Storage unit made of 19mm BWR plywood with laminate finish of approved shade.Complete with all hardwares of ebco/hettich make or similar. etc. The rate should included debris clearing, Materials lead and lift, cleaning , etc. complete as per drawing. Refer Detail No:4

PANTRY STORAGE :2173mm x 600mm x 750mm - Supply and fixing of Pantry Storage consists of 2 Nos of 19mm BWR Plywood clad with 4mm thick teak veneer crown cut PU polish satin matte finish. Supported on 19mm BWR plywood clad with 2mm thick HDF duco paint to approved shade finish Flip up wire manager is provided on top with storage and shuttering. Complete with all hardwares of ebco/hettich make or similar. etc. The rate should included debris clearing, Materials lead and lift, cleaning , etc. complete as per drawing. Refer Detail No:4

COMPUTER TABLE - 1300mm x 600mm x 750mm - Supply and fixing of Computer Table with Key board drawer and table top, Drawer with 6 lever lock with set o 2keys of non corrosive materials, Sliding of keybaord - Provided with two telescopic channels with balls,

OFFICE CHAIRS - Supplying & placing of The Seat and Back Cushion of the chairs should be pressed on 12 mm hot press moulded ply. The seat cushion of the chair should be 50mm thick with density of 45±2 Kg/m^ polyurethane moulded and back cushion should be 46mm thick with density 33±2 Kg/m^. The polyurethane foam shall be as per manufacturer's specification. The hardness of foam shall be 16±2 kgf as per IS7888 for 25% compression and it should be covered with black or brown fabric shade, The arms of the chair should be black, The lift mechanism should be pneumatic or hydraulic, The tilting mechanism should be adjustable with following features: a. 360° revolving type. b. Single point control. c. Front-pivot for tilt with feet resting on ground ensuring more comfort, d. Tilt tension adjustment. The pedestal should be five legged injection coated with black nylon polyurethane and fitted

Providing and laying 20mm thick FALSE WOODEN FLOORING of PERGO ORIGINAL, Armstrong, Egger or equivalent (matt finish) consisting of panels of size 1194mm x 194mm or as per manufacturer specification having class of use - 23/33, wear resistance level of AC5 as per EN 13329 with a high pressure surface treated with aluminium oxide and a specially patented SURFACE GUARD + on top of a high density fiber board with a density of 910 Kg/ cum. The panels having a click system tongue and groove joint to secure a long lasting joint with the edges duly impregnated with paraffin. The Floating laminate flooring shall be laid over a 0.20mm thick polythene film to form a vapor barrier and 2mm to 3mm thick approved FOAM The panels used shall be of high solidity, high impact strength, high temperature resistance without change in shape). Each panel shall have click system (tongue and groove profile) and to be laid in approved pattern with suitable glue as per manufacturers specifications including alround suitable egde profile alround/wherever required for firm end lockin

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc. to be paid separately) including cost of materials, labour, usage charges of machinery complete as per specifications and as per directions of the Engineer-in-Charge.

Supplying and erecting in position of 250 Litres capacity Industrial Model Reverse Osmosis Water-cum-Purifier to deliver Potable Water with World Health Organisation (WHO) Standards with following accessories. (a) MS Skid - 1 No. (b) Media 11054 No. Vessel with 20 nb Multiport Valve (with Media Pubble and Fine Sand and Activated Carbon Filling) set (c) Feed Pump 0.50 HP – 1 No. (d) Vertical Pump 2-9, 2.00 HP / Single Phase – 1 No. (e) Membrane 40 x 40 filmtech (or) equilaents / Osmonic (USA) - 1 No. and Membrane Pressure Vessel 40 x 40 -1No. & Pressure Gauge - 2 Nos. (f) Flow Meter - 1 No. 20” Filter with Housing - 1 No., Low Pressure Switch - 1 No., Level Switch - 1 No. & Necessary CPVC Pipes and Fittings. The system shall be provide with Two Panel Control System with necessary Stainless Valves and Fittings and Float Control etc. The rate should be inclusive of all civil works,wherever necessary to install the System in position and intact.

Supplying and fixing Writing WhiteBoard 4′ x 6′ with the following specifications. Non Magnetic , Melamine writing surface Triple Layer writing board Suitable for marker writing and effortless erasing with the help of a Duster. Comes with anodized aluminum frame & ABS corners alongwith Wall mounting hooks to support and sturdy looks also give a longer life to the board Best suited for Office home and educational & Instituitional use

Supplying and fixing Writing WhiteBoard 4′ x 4′ with the following specifications. Non Magnetic , Melamine writing surface Triple Layer writing board Suitable for marker writing and effortless erasing with the help of a Duster. Comes with anodized aluminum frame & ABS corners alongwith Wall mounting hooks to support and sturdy looks also give a longer life to the board Best suited for Office home and educational & Instituitional use

Supplying and fixing pin up board 4'x6' with the following specifications. Material - Alloy Aluminium Frame, Softboard Core, Premium Flocked Fabric (Velvet) Cloth Surface & Virgin ABS Corners, The back of the board can withstand repeated use and will keep the documents in place with a secure hold. With its strong and elegant frame, the YAJNAS bulletin board will add a perfect feel to the environment of your office, home or school. This board is the perfect blend of stylish and sturdiness that will make a great addition to any space. The Bulletin board corners are designed to be equally strong. The surface will re-close when push-pins are removed, making it long-lasting. Precision riveting of these corners ensures that the edges are properly sealed, thus making the product weatherproof while imparting a seamless finish to it.

Stainless Steel Plain Pedal Bin With Plastic Bucket And Lid| Trash Can, Round Shape 12 Litre Capacity Dustbin with Step-On Opening Mechanism

Supply & stacking of red earth at site to the departmental guage for pre-measurements which is of light textured, crystalline, porous and friable and not of generally acidic or neutral but not of alkaline and should be fertile, including seignior age charges, cost of transportation, loading, unloading, stacking and inclusive of all taxes etc., complete.

Supply of well decomposed Farm yard Manure in a powdery form, devoid of soil sand, stones, plastics and other materials, highly nutrient and which supports plant growth.

Mixing charges of Red soil, sand and manure uniformly (1:1:1) for Preparation of soil mixture (excluding material cost)

Spreading of red soil, gravel or sand including watering and rolling which hand roller for every 75 mm thickness - including hire charges of roller.

Supplying and Planting of Cassia fistula tree sapling of height 240 – 300 cm in polythene bag of size 20x21 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Supplying and Planting of Sterlitzia nicolia sapling in polythene bag of size 20x21 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Supplying and Planting of Heliconia pssitcorium tree sapling of height 120 – 180 cm in polythene bag of size 20x21 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Supplying and Planting of Calathea lutea tree sapling of height 120 – 180 cm in polythene bag of size 20x21 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Supplying and Planting of Plumeria alba tree sapling of height 210 – 240 cm in polythene bag of size 20x21 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Supplying and Planting of Cymbopogon citratus tree sapling of height 210 – 240 cm in polythene bag of size 20x21 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Bermuda grass including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Lobelia erinus shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, ransportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Brassia variegated shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, ransportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Schefflera variegated shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, ransportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Hymenocallis littoralis shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, ransportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Lysimachia nummularia including loading and unloading charges, ransportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of zephyranthes -yellow and white including loading and unloading charges, ransportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of ruellia simplex including loading and unloading charges, ransportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Supplying of Rectangle (3') pot of 90 inch dia and size 45*45 in Centimeter, Various size pots made up of 6mm rod & chicken mesh with cement moulded pots and designer painting with various size plates including loading and unloading charges, transportation, etc as directed by the site in-charge."

Supplying of Plastic pot size of dia 24 inch brown with plates including loading and unloading charges, transportation, etc as directed by the site in-charge.

LT CT TNEB METER BOX: 'Supply, Installation, testing and commissioning of compartmentalised LT CT 3Phase, EB Metering box of outdoor weather proof type with MS mounting stand, Copper busbars with supports, Test Terminal Blocks, CTs, Internal control wiring etc., as per local TNEB standards

Supply and fixing of 400 A TPN switch disconnector fuse units in sheet steel enclosure with HRC fuses double break on suitable angle iron frame work with MS cable entry boxes with earth connection only.

MAIN LT PANEL: 'Supply, Installation, testing and commissioning of 3Phase, 415Volts, Main LT Panel board of Indoor, Cubicle floor mounting type made out of 2mm thick CRCA Sheet with powder coated finishing, MS base frame, double internal earthing arrangements, 400Amps, rating TPN Copper busbars with interconnection busbar, etc., comprising of the followings: EB Incomer : 1 No. 400Amps, 25kA, 4Pole, Thermal magnetic MCCB with Ext.RHOM DG Incomer: 1 No. 400Amps, 25kA, 4Pole, Thermal magnetic MCCB with Ext.RHOM Common C/O Incomer: 1 No. 400Amps, 4Pole Automatic Changeover Switch with EB ON and DG ON LED Indication lamps Metering : 2 Set of RYB LED Indication lamps 2 Nos. of Multifunction Meter with RS 485 2 Set of Current Tranformers (400/5A, Cl-1), 1 No. 400/5A CT for APFCR 2 Set of Control MCB and Electrical Interlocking between EB & DG Incomers Outgoings: 1 No. 200A, 25kA, TP+N, TM MCCB with Ext. RHOM (Fire) 2 Nos. 160A, 25kA, TP+N, TM MCCB with Ext. RHOM (APFCR & Spare) 6 Nos. 125A, 25kA, TP+N, TM MCCB with Ext. RHOM (VRF TPDBs & TPDBs ) 14 Nos. 63A, 25kA, TP+N, TM MCCB with Ext. RHOM (LDBs, PDBs, ACDBs, Ex.LDB, PHE & Spare) 06 Nos. 32Amps DP MCBs

APFCR PANEL - 50KVAR:'Supply, Installation, testing and commissioning of 3Phase, 415Volts, APFCR (Capacitor) Panel board of Indoor, Cubicle floor / wall mounting type made out of 2mm thick CRCA Sheet with powder coated finishing, MS base /wall frame, double internal earthing arrangements, 160Amps, rating TPN Copper busbars with interconnection busbar, etc., comprising of the followings: Incomer : 1 No. 160Amps, 25kA, 4Pole, Thermal magnetic MCCB with Ext.RHOM Metering : 1 Set of RYB LED Indication lamps 1 No. VAF Meter with RS 485 1 Set of Current Tranformers 1 No. 6 Stage APFCR Relay 2 Set of Control MCB Outgoings: 2x15kVAR Heavy Capacitor bank controlled by 1x40A, 4P MCB, 3x05kVAR Heavy Capacitor bank controlled by 1x25A, 4P MCB, 1x03kVAR Heavy Capacitor bank controlled by 1x20A, 4P MCB and 1x02kVAR Heavy Capacitor bank controlled by 1x20A, 4P MCB including ON-OFF Push buttons, internal control wiring, etc.,

DG SET - 200KVA with Standard Control Panel - 'Supply, Installation, testing and commissioning of 1 x 200VA, Silent type Diesel Generator Set complete with suitable size Acoustic enclosure Diesel Engine suitable for Generator application, developing 1500RPM with an overloading capacity of 10% for one hour in any 12 continuous hours operation generally confirms to BS:5514, directly coupled to 200KVA at 0.8 Power factor, 415V, 3Phase , 4wires, 50cycles per second self excited, self regulated, with brushless excitation, Alternator generally confirms to BS:5000/IS:4722. DG set shall be complete with radiator, residential type silencer, electronic governor, cable termination box, MS mounting frame, fuel piping, diesel day tank, 24VDC Battery, Battery mounting frame, oil level indicator with gauge board, and all other accessories as per standard specifications. 'Diesel Generator set shall be mounted on cushy foot or similar type of vibration Isolators. The cost of Exhaust pipe shall be excluded in this item. The DG Set shall be suitable for auto-mains failure start and auto / manual operations. The DG Should be supplied with Auto-Start-Stop Control panel with suitable rating switchgear.

ELDB-1 to 3 & General Power: Supply and fixing of 12 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1no. 32A DP MCB switch as incoming and 10 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End

LDB-1 to 3 & PDB-1 to 3 : Supply and fixing of 7 segment 6 way TPN MCB sheet steel distribution board (Higher end) with metal / acrylic door cover flush type /surface type fitted with busbars and neutral links with single / three phase MCB outgoings and seperate 4 way provision for accomodating one no. 4 pole incoming MCB / Isolator and another seperate 4 way provision for accomodating one no. 4 pole ELCB / RCD (totally 8 ways in one segment) (3x 6 ways in each segment) and seperate provision for MCB / Isolators ( totally 18 nos.) for sub incomers in 3 segments with lable holder and provison for taking up cable for size not less than 35 sq.mm. with the following on wall with earth connection only. (SD-622)

External LDB - Supply and fixing of 7 segment 4way TPN MCB sheet steel distribution board (Higher end) with metal / acrylic door cover flush type /surface type fitted with busbars and neutral links with single/three phase MCB outgoings and separate 4 way provision for accommodating one no.63A 4 pole incoming MCB / Isolator and another separate 4 way provision for accommodating one no. 63A 4 pole ELCB / RCD (totally 8 ways in one segment), (3x 4 ways in each segment) and separate provision for 6A to 32A SP MCB-12Nos. / Isolators (totally 12nos.) for sub incomers in 3 nos.63A DP MCB segments with label holder and provision for taking up cable for size not less than 35 sq.mm. with the following on wall with earth connection only.

AC/PDB-1 to 3: Supply and fixing of 7 segment 6 way TPN MCB sheet steel distribution board (Higher end) with metal / acrylic door cover flush type /surface type fitted with busbars and neutral links with single / three phase MCB outgoings and seperate 4 way provision for accomodating one no. 4 pole incoming MCB / Isolator and another seperate 4 way provision for accomodating one no. 4 pole ELCB / RCD (totally 8 ways in one segment) (3x 6 ways in each segment) and seperate provision for MCB / Isolators ( totally 18 nos.) for sub incomers in 3 segments with lable holder and provison for taking up cable for size not less than 35 sq.mm. with the following on wall with earth connection only.

Vertical TPDBs (VRFs & General) - Supply and fixing of 6way Vertical Triple pole and neutral MCCB sheet steel enclosure distribution board with double door (metal) with 1 No. 125A, 25kA, 4P MCCB as incoming and 4 Nos. 63A 3P MCB, 1 Nos. 32A TP MCB, 03 Nos. 6A to 32A SP MCB as outgoing on suitable angle iron frame on wall with earth connection only. Higher End

Supply and Laying of 3 1/2 x 240 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and Clamping of 3 1/2 core x 300 Sq.mm PVC armoured LTUG aluminium cable on post or on wall MS-clamps, saddles, plugs, screws etc., complete including transport charges of UG cable.

Supply and Clamping of 3 1/2 core x 150 Sq.mm PVC armoured LTUG aluminium cable on post or on wall MS-clamps, saddles, plugs, screws etc., complete including transport charges of UG cable.

Supply and Clamping of 3 1/2 core x 120 Sq.mm PVC armoured LTUG aluminium cable on post or on wall MS-clamps, saddles, plugs, screws etc., complete including transport charges of UG cable.

Supply and Clamping of 3 1/2 core x 50 Sq.mm PVC armoured LTUG aluminium cable on post or on wall MS-clamps, saddles, plugs, screws etc., complete including transport charges of UG cable.

Supply and Clamping of 3 1/2 core x 35 Sq.mm PVC armoured LTUG aluminium cable on post or on wall MS-clamps, saddles, plugs, screws etc., complete including transport charges of UG cable.

Supply and Clamping of 3 1/2 core x 25 Sq.mm PVC armoured LTUG aluminium cable on post or on wall MS-clamps, saddles, plugs, screws etc., complete including transport charges of UG cable.

Supply and laying of 2 x 6 sq.mm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good

Supply and fixing of brass cable gland for 2 x 6 sq.mm. PVC armoured LTUG cable with earth connection

Supply and fixing of brass cable gland for 3-1/2 x 25 sq.mm. PVC armoured LTUG cable with earth connection

Supply and providing cable end termination of 3-1/2 x 25 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete

Supply and fixing of brass cable gland for 3-1/2 x 35 sq.mm. PVC armoured LTUG cable with earth connection

Supply and providing cable end termination of 3-1/2 x 35 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete

Supply and fixing of brass cable gland for 3-1/2 x 50 sq.mm. PVC armoured LTUG cable with earth connection

Supply and providing cable end termination of 3-1/2 x 50 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete

Supply and fixing of brass cable gland for 3-1/2 x 240 sq.mm. PVC armoured LTUG cable with earth connection

Supply and providing cable end termination of 3-1/2 x 240 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete

Supply and fixing of brass cable gland for 3-1/2 x 300 sq.mm. PVC armoured LTUG cable with earth connection

Supply and providing cable end termination of 3-1/2 x 300 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete

Supply and fixing of brass cable gland for 3-1/2 x 150 sq.mm. PVC armoured LTUG cable with earth connection

Supply and providing cable end termination of 3-1/2 x 150 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete

Supply and fixing of brass cable gland for 3-1/2 x 120 sq.mm. PVC armoured LTUG cable with earth connection

Supply and providing cable end termination of 3-1/2 x 120 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete

Supply and erection of GI Hot Dip / Powder Coated 16 SWG Perforated type Cable Tray with 150mm width and 50mm height with all the fixing accessories

Supply and erection of GI Hot Dip / Powder Coated 16 SWG Perforated type Cable Tray with 300mm width and 50mm height with all the fixing accessories

Supply and Run of 2 of 2.5 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable gauge MS conduit pipe Concealed in wall and ceiling with continuous earth wire connection of 2.5 sq mm copper wire and making good of the concealed portion

Supply and Run of 4 of 10 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable gauge MS conduit pipe on wall and ceiling with continuous earth wire connection of 10 sq mm copper wire with painting of suitable colour.

Supply and Run of 2 of 6 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable gauge MS conduit pipe concealed in wall and ceiling with continuous earth wire connection of 6 sq mm copper wire with painting of suitable colour.

Supply and run of 2 of 4 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in suitable heavy gauge MS conduit pipe concealed in wall and ceiling with continuous earth wire connection by 4 sq.mm copper wire and making good of the concealed portion wiith suitable colour

Supply and fixing of 1 no.6A two module 5 pin socket , 1 no. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End

Supply and fixing of 2 nos.6A two module 5 pin socket , 2 nos. 6A one module switch on suitable module surface mounting Box (Plastic ) with module cover plate (plastic) on wall with connections. Higher End

Supply and fixing of 2nos.6A two module 5 pin socket , 2 nos. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End

Supply and fixing of 1 no.6/16A two module socket , 1 no. 16A one module switch on suitable module surface mounting Box (Plastic ) with module cover plate (plastic) on wall with connections. Higher End

Supply and fixing of 1 no.6/16A two module socket , 1 no. 16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS FRLS copper conductor of 1100 V grade in suitable heavy gauge MS conduit pipe on wall and ceiling with MS accessories with Module GI switch box in flush wall with 6A one way module switch with module front plate with painting of Suitable colour with continuous earth wire connection of 1.5 sq.mm copper wire for Open MS conduit Light point / fan point (for electronic regulator) ( 6 points / Coil) Higher End - (Primary)

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS FRLS copper conductor of 1100 V grade in suitable heavy gauge MS conduit pipe on wall and ceiling with MS accessories with continuous earth wire connection of 1.5 sq.mm copper wire for Open MS conduit Light point / fan point (for electronic regulator) ( 6 points / Coil) Higher End - (Secondary)

Supply and fixing of 24W LED 2x2 square type Recessed fitting with LED (Higher end) on false Ceiling with suitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting

Supply and fixing of 18W LED Round type Recessed fitting with LED (Higher end) on false Ceiling from ceiling with PVC unsheathed copper leads from terminals to the fitting.

Supply and fixing of 48W LED street light fitting with LED (Higher end) with 32mm dia. GI pipe (class B) with 1 no.32 mm GI bend complete on the existing post/ on wall with PVC unsheathed copper leads with MS clamps and with painting .

Supply and fixing of WT bulk head fitting with guard suitable with 7W / 9W LED bulb

Supply and fixing of K-Lite make External road lighting Pole with 60Watts LED light fitting - KL-7034 Juno, Dimension : 600mm Dia and 3500mm Long from the FFL including all supporting accessories, interconnection flexible cables, etc., • Luminaire body made of spun aluminium with extruded aluminium alloy (grade 6063) and non corrosive SS fasteners. • Shielded light. • Non yellowing UV stabilized translucent acrylic diffuser. • Silicone gasket. • Die cast aluminium mounting plate with an anchorage unit made out of hot dip galvanised steel for extra guarantee against corrosion. Luminaire can be aligned on the mounting plate around 360°. • Cable entries for through-wiring of mains supply cable. • Integral constant current power supply • CRI (Ra) : ≥80 ( 90 CRI - On Request ) • Prewired with LED driver and suitable for operating on 240V, 50Hz single phase ac supply.

Supply and erection of 36Watts, 1130mm Long LED Linear light fitting suspended from the ceiling with hanging supports, end cap, PVC unsheathed copper leads from terminals to the fitting and fixing accessories

Supply and erection of 15Watts, Round type COB/ Wall Bamboo LED light fitting suspended from the ceiling with hanging supports, PVC unsheathed copper leads from terminals to the fitting and fixing accessories

Supply and erection of K-Lite make 12Watts Polar Quad Asy Bollard LED Light fitting (KL-4729, Dimension 100mm Square X 900mm Height from the FFL) with MS base, concreting and masonry work for fixing the post, connecting wires, and fixing accessories • Luminaire body made of square aluminium tube (grade 6063) with aluminium components and SS fasteners. • Polycarbonate optical lens. • Luminaire integrated with 12W LED. • Silicone gasket. • Mounting plate die cast aluminium double powder coat with an anchorage unit and stainless steel fixing screws. • Cable entries for through-wiring of mains supply cable. • Integral constant current power supply • CRI (Ra) : ≥80 • Prewired with LED driver and suitable for operating on 240V, 50Hz single phase ac supply

Supply and erection of Name board lighting using IP65 rated LED with connecting wires and all the fixing accessories

Supply and erection of 9Watts, 1feet long, Fancy type wall mounted LED Light fittings with connecting wires and all the fixing accessories

Supply and erection of 15Watts, Round type Globe or circular pendent LED light fitting suspended from the ceiling with hanging supports, PVC unsheathed copper leads from terminals to the fitting

Supply and installation of Printed Ceiling- Supply of European Standard Premium PVC Membrane installed with Aluminium Profile. PVC harpoon welded with high frequency on the perimeter of the membrane according to shape and size -Thickness of Membrane - 0.18mm -Weight - 250 - 300 gsm +/- 2% -% of light transmission - 75.00% -Fire Rating - BS1D0 in accordance with EN 13501-1. -Warranty - 10 years -No Heavy Metals - ROHS Certified -Manufactured in ISO 9001:2015 certified factory in India including connecting wires and clamps screw and etc.

Supply and Installation of Stretch Lighting - 6000K - 24V Osram Rigid Block LED, 160 Degree Best Viewing Angle with PMMA Lens ROHS Certified Power Consumption : 4W Per Rigid Block LED SMPS - Iceil Drive with 3 Year Warranty LED Life span : 30000 Hours / 5 Years connecting wires and clamps screw and etc.

Supply and erection of Profile light (LED) fitting suspended from the ceiling using 50Watts, 2260mm Long LED Linear light fitting suspended from the ceiling with hanging supports, end cap, PVC unsheathed copper leads from terminals to the fitting and fixing accessories

Supply and fixing of Multiple Pendent type LED Light fitting with PVC unsheathed copper leads from terminals to the fitting and to complete necessary accessories and etc to complete the work.

Supply and fixing of 28Watts GATE FIXTURE FITTING with cool day light suitable for wall / roof sheet mounting, made out CRCA powder coated body,IP65 aluminium reflectors, poly methyl meth acrylate (PMMA) diffuser, glare free light, including electronic drivers, day light colour LED lamps, inter connecting wiring with suitable fixing clams, hooks as required including accessories all inclusive.

Supply and erection of 450mm Sweep Wall mounted type fan with fixing accessories

Supply and fixing of 300mm (12") sweep(Heavy Duty) AC exhaust fan complete with necessary wall opening and making good of the wall .

Supply and fixing of louvers shutters arrangements for 300mm (12") sweep AC exhaust fan

Supply and fixing of 1200mm (48") sweep AC ceiling fan 5 star rated complete ( Higher end) with 2 module 100W fan step regulator (Higher end) with 1 metre down rod with fan clamp with side plates and cross arm of size 450mm (18")

Earthing as per the ISI specification with an earth electrode of 2.10 metre Class 'B' GI pipe of dia not less than 40mm with copper earth plate of size 125mm x 50mm x 6mm with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry

Supply and erection of 17.2mm, 3mtr long, Copper Bonded earth rod with backfill compound, including civil works, heavy duty Plastic Chamber cover withstand load of 60kN, etc., as per IS 3043 standards

Supply and run of 25mm x 3mm tinned copper flat with necessary clamps / supports on wall / floor / ground for earth connection

Supply and Run of 1 of No.8 SWG copper wire for earth connection

Supply and Run of 1 of No.8 SWG copper wire in suitable PVC rigid pipe on wall / floor / ground for earth connection

Coil earth to street light poles with No.8 SWG GI wire of 11.5 metres of length in which 10 metres of total length compressed in to a coil of one meter length (75mm to 100mm dia) connected suitable with hexagonal earth bolt of size 8mm in to 25mm welded on the pole at one end with a coil position fixed on the earth

Supply and erection of 40-63Amps, 4Pole MCB with IP65 rated thermoplastic enclosure for ODU nearyby control

Supply of '2m x 1m Rubber Mat suitable for 11 KV installation confirming to IS

Supply of First Aid Box complete with all First Aid Medicines

Supply and fixing of Shock Treatment chart with Glass frame

Supply and fixing of 4 Nos. Fire Buckets made out of 40 x 40 x 6mm MS Angle

Supply and fixing of Fire Extinguishers Co2, 4.5Kg confirming to TAC norms

Supply and fixing of Metallic Danger Board as required by the Electrical Authorities (415Volts & 230Volts)

Supply and Installation for 2KVA UPS with Battery, Single Phase UPS (Single Phase Input & Single Phase Output) System with sealed maintenance SMF Type Battery - 2Hours back up with Battery Stand, interconnection cooper cables, etc.,

Supply and fixing of DP MCB sheet steel enclosure with 1 no 32A DP MCB switch with necessary fixing accessories

Supply and erection of Canon Digital Photocopier (Xerox) Machine IR-3300 / 3235 Type of Product : Laser Multi functional Core Functions : Print, Copy, Scan & Send First Copy Time : 3.9 Sec Multiple Copies : 1 to 999 Sheets Print Speed : 45ppm The laser beams engrave the image or text that you have sent to print on the surface of the drum. When using a copier this process is done using light, the light scans the page required for printing and converts it into an image

Supply and erection of All-in-one Desktop of HP 27-cb1456in Core i5 (8GB DDR4 /Windows 11 Home/27 Inch Screen/27-cb1456in) with 600VA UPS, Keyboard, Mouse, 27 inches, 11th Gen Intel Core i5-1235U 6 x 1.8 GHz (Turbo Speed upto 4.2 GHz) Cores Hexa Core, 12 Threads, 18 MB Cache, UHD Graphics 730 Graphics, 8 GB DDR4 RAM Smallest and 512 GB SSD. Ethernet (LAN), HDMI, Multi Card Reader, WiFi, Bluetooth v5.0 3 x USB 3.0, 1 x USB Type-C and Inbuilt Microphone

Supply and erection of BenQ TK700Sti (3000 lm / 1 Speaker / Wireless / Remote Controller) 4K UHD HDR, Excellent Colors 96% REC 709, Upto 200inches screen,Sports Mode,Android TV,16ms Low Input Lag,Google Cast,3D Keystone Smart Home Cinema Short Throw Projector (White) Aspect Ratio - 16 : 09, Brightness- 3000ANSI lumes Connector type - Wifi, Bluetooth, USB & HDMI Contrast Ratio- 1000:1, DIsplay Resoultion-3840 x2160p Life Hours- 15000Hrs, Power - 1Phase, 240Volts, 305Watts

Supply and installation of Wheel Chair Platform Lift with the following specifications HYDRAULIC WHEELCHAIR LIFT 1) 3 PHASE POWER PACK 2) 0.5 M/SEC SPEED 3) LIFT CABIN SIZE 1200MM X 900MM 4) ACP SHEET FOR FRAME COVER 5) 7.7KW POWER PACK 6) SS304 CABIN 7) CABIN FLOOR MATE 8) ARD (POWER CUT LIFT COME TO GROUND LEVEL) 9) ALARAM IN CABIN 10) ENTER GRILL DOOR 11) HALF CABIN HEIGHT 4 OF 3 FEET

Supply and installation of All-In-One Digital Metal Podium with the following specifications: Digital Podium is a complete solution for any classroom, boardroom / training room and Auditorium. It has a built-in sound system (Amplifier, Gooseneck Microphone, Wireless Microphone, etc..) and can be interfaced with all multimedia devices and facilities that the Presenter might employ as teaching or communication tools. a) Type: Free Standing, Lockable Caster Wheel b) Construction : 1.6 mm CRCA Steel, Polymer Powder Coated Metal Top c) Storage : Keyboard, Mouse, Drawer for Visualizer , Side Shelf for Laptop d) Monitor : Built in Touch Monitor 21.5” with motorised tilt Mechanism e) Resolution : 1920 x 1080 (Full HD) f) Features : Power ON / OFF, Display ON/ OFF, External PC Input, VGA/HDMI g) I/O PArts: USB 3.0 x 1, HDMI IN & LAN: RJ-45 LAN Port h) Wireless Microphone System: VHF Hand Held Microphone x 1, VHF Collar Microphone x 1, Wireless Microphone Receiver x 1 i) Gooseneck Microphone: 80 cm Length, with Light Double Soft Copper Tube, 1.5m Wire, 3 cores Cannon Plug. j) Amplifier and Speakers: 120 w RMS Amplifier and 2 x 30 watt inbuilt Speakers/ 2 x 30 watt wall speaker k) Power SUpply: 230Volts, 1Phase, 120Watts l) 4GM RAM, 1TB SATA H/D, Built-in WiFi, i3 - Windows10 k) Annotation Software: Annotation Features like draw, choose, pens, annotate, erase, color, shape, size, text, edit, fonts, stamp, move, capture, picture, video, save, rotate, undo, image, gallery, print, floating keyboard, background etc. Network classroom feature to conduct remote teaching by having interaction through all type of media Audio, Video and Text. (Approx. Size: 750 x 700 x 1200 (L x W x H))

Supply and erection of 20-30Watts Ambient Circuit ype LED light fitting suspended from the ceiling with hanging supports, PVC unsheathed copper leads from terminals to the fitting

Supply and erection of 10Watts IP-65 rated Wall / Column mounted type Up-Down LED Light fitting with fixing accessories

Supply and erection of LED Strip light fitting with suitable driver and fixing accessories (5Watts / Meter)

SOLAR PV PLANT - 'Supply, erection, testing and commisioning of '30 kWp On Grid Solar PV Plant' comprising of: i) Solar panels of type Mono Crystline, PERC, etc. ii) Power Conditioning Unit (PCU)with MPPT, Inverter, Controls, Protection Devices, Interconnecting D.C. cables, Connectors, Junction Boxes and accessories. iii) D.C. D.B iv) A.C. D.B v) A.C. cables and accessories vi) Lightning arrestor, earthing, etc. vii) Module Metallic Mounting Structures viii) Installation, Testing and Commissioning corresponds to BIS and IEC requirements

Supply and erection of complete set of Signages (Entry, Exit & Other signages) as per standard building requirements

Supply, Installation, Testing and commissioning of 32 channel 2 SATA NVR, with 8TB Hard Disk Drive 2 nos, New logical and visualized GUI design Dual-OS design to ensure high reliability of system running, ANR technology to enhance the storage reliability when the network is disconnected, Configurable normal or hot spare working mode to constitute an N+1 hot spare system Video Input and Transmission, Connectable to the third-party network cameras Compression and Recording, H.265+ compression effectively reduces the storage space by upto 75%, Full channel recording at up to 12MP resolution HD Video Output  HDMI1 / VGA1 outputs provided  HDMI1 Video output at up to 4K ( 3840 × 2160 ) resolution Storage and Playback, Upto 16 SATA interfaces and 1 eSATA interface for HDD connection, Support upto 10TB capacity for each HDD, Smart search for efficient playback. and smart playback to improve the playback efficiency,Supports VCA search for fire/ship/temperature/temperature difference detection triggered video files, POS information overlay on live view and playback, POS triggered recording and alarm Network & Ethernet Access  Hik-Connect for easy network management, 2 Gigabit Ethernet network interfaces. (Make : Hikvision / Dahua / Sony.

Supply of 4MP, Internet Protocol fixed BULLET CAMERA/DOME CAMERA (INDOOR & OUTDOOR)with following specification: a) 1/2.5" Progressive Scan CMOS, b) 3840 × 2160 @15 fps,2.8/4 mm fixed lens,01 lux @ (F1.2, AGC ON), 0.028 lux @(F2.0, AGC ON), 0 lux with IR, H.265+, H.265, H.264+, H.264, 2 Behavior analyses ( Line crossing detection, intrusion detection) c) Face Detection d) 120dB WDR, e) BLC/3D DNR/ROI, IP67 compliedf f) On-board Storage - Built-in micro SD/SDHC/SDXC card slot, up to 128 GB, g) Shutter Speed 1/3 s to 1/100,000 s, h) 3-Axis Adjustment Pan: 0° to 360°, tilt: 0° to 100°, i) rotate: 0° to 360°, 2.8 mm, j) horizontal FOV: 102°, vertical FOV: 53°, diagonal FOV: 124°, k) Lens Mount M12 & IR Range I5: up to 50 m, l) Image Settings Rotate mode, saturation, brightness, contrast, sharpness adjustable by client software or web browser, m) Power Consumption and Current-12 VDC, 0.7 A, max. 7.5W PoE: (802.3af, 36V to 57V), 0.3 A to 0.2 A, max. 9W n) Camera out fitted with metal housing so as to prevent the lens from damages during physical abuse. with Camera Stand. (Make: Dahua/Panasonic)

Supply, Installation, Testing and Commissioning of 32" smart LED TV with following specifications a) Full HD 1920 x1080 (4K monitor) b) IPS pannel c) Slim back light LED module d) 900 PMI e) Triple XD engine f) Dynamic scanning g) ANR h) True colour generator i) 8modes of picture j) picture wizardIII k) Real cinema 24P l) HDMI -3nos m) USB -3nos n) Built in LAN o) Magic remote p) Dimension 1242 x 724 x 55.1min(37). (Make: Sony/ LG /Samsung).

Supply and Clamping of CAT 6 unarmoured cable in suitable PVC Pipe 1" thick on wall / ceiling with connected PVC accessories with clamps, saddles etc., complete. (Between ethernet switch to camera and radio modem) i. Application : Primary (Campus), Secondary (Riser), Tertiary(Horizontal) IEEE 802.3 : 10Base-T; 100Base-T; 1000Base-T IEEE 802.5 16 MB; ISDN; TPDDI; ATM ii. Standards: ISO/IEC 11801 2nd ed.; IEC 61156-5 2nd EN 50173-1; EN 50288-6-1,EIA/TIA 568C.2, RoHS Compliant. Fire Rating: PVC : IEC 60332-1. iii. Conductor - Bare Copper Wire iv. Insulation - Polyethylene v. Twisting - 2 Cores to the pair vi. Cable lay up - 4 Core to the pair It has diameter of (23 AWG) 0.550 ± 0.015.Insulation : Polyethylene.GI wire of size is 0.90 ± 0.030mm.

Supply and Fixing of Rack with Accessories -Higher end 6U Rack with fan extra for the above rack. (speaker/data/cctv)

Supply and fixing of POE 24 port switch 10/ 100 / 1000 Base -T / 2 x 1000Base-FX / 20Gbps bandwidth / IEEE803.af/at compliant PoE+ / RJ45 supports auto MDI/MDI-X function / Auto negotiation speed, half/full-duplex / Store and forward / Max packet size: 10kbytes / Wide range power design (12~56VDC) / Operating temperature (-40 ̊C ~ +75 ̊C) / Reverse polarity protection / Resettable fuse to protect against overcurrent / IP-40 protection / EFT protection for power line.

Supply, Fixing and Termination of CAT 6 Cable RJ 45Jack Single Point ( Point to Point ) Crimping, Testing and arrangement charges.

Supply and Installation for 1KVA UPS with Battery, Single Phase UPS (Single Phase In & Single Phase Out) Capacity - System with Battery - 2 Hours back up and battery stand .

Supply and fixing of outdoor 4X6 PVC box with 102mmX77mmX102mm with all fixing accessories.

Supply, installation, testing and commissioning of Long Range Wifi Device of following Specification: Networking Interface: (1) GbE RJ45 Port Power Method: PoE+, Pasive poE(48V) Max TX power: 2.4 GHz Antenna gain: 2.4 GHz Mounting: Wall or Ceiling Mounting Wifi Satndards : 802.11a/b/g Wireless security: WPA-PSK, WPA- Enterprises(WPA/WPA2/WPA3) VLAN: 802.1Q Concurrent Clients: 300+

Supply, Installation,Testing & commisioning of 480 watts P.A Booster Amplifier with the output power of 1350 watts maximum, 500watt rms at 10% Thyristor harmonic distortion(THD), 850watt RMS at 5% THD, 800 watts RMS at 2% THD and the power supply AC voltage ranging from 220-240 volt, 50/60 hertz. with the DC input of 48 volt and 1000watts has tone controls of Bass=+- 10 db at 100 hz weighing 42kg with the speaker output of 2Q,4Q.70volt&100volt has power consumption of 1600VA AC &12A DC and 100db output regulation at 1khz no load to full load ratio. The signal to noise ratio is 60db with the imnput channels of 0.8mv/4.7kq,3*Aux 100mv/50kq.The frequency response of 50-15000hz+-3db.(Make:Ahuja SSA 10000 /Bosch or its equivalent)

Supply, run, testing and commissioning of 2Core x 1.5sq sqmm PVC insulated Armoured Speaker Cable in suitable 25mm dia Pvc Rigid pipe concealed on wall and ceiling with continuous earth wire connection with painting of suitable colour.

Supply and Fixing and Termination of CAT 6 Cable RJ 45Jack Single Point ( Point to Point ) Crimping, Testing and arrangement charges.

Supply, Fixing and Termination of RJ 11 Single Point ( Point to Point ) Crimping, Testing and arrangement charges.

Supply & Installation of CAT 6 PVC Module Box I/o socket & face plate single socket Erection and arrangement chargers (Higher end)

Supply and fixing of LAN Network Switches Un-Managed 10/100/1000 - 24 Port and 24 Port Patch Panel- Unloaded erection and arrangement chargers.

Supply, runing, testing and commissioning of 2 Pair Unarmoured 0.5mm Telephone cable in suitable Pvc Rigid pipe concealed on wall and ceiling with continuous earth wire connection with painting of suitable colour.

Supply, Installation, testing and commissioning of VRV/VRF air-conditioning system Cooling only comprising of Modular type high efficiency DC Scroll / Twin Rotary Multiple Compressor with DC inverter, High efficiency heat transfer Cooling Coil suitable for Environment friendly HFC R410A / R407C refrigerant, Air cooled propeller type condenser fan with DC motor drive, interconnecting piping, insulation etc., Micro-processor control panel suitable for automatic operation, High speed calculation inverter control, active oil control mechanism incorporating all safety functions as per technical specifications & other points listed below. Unit shall have a minimum of 2 compressors. And each compressor shall run independently even though there is a failure in the other compressor. The unit mounted starter panel shall be complete with IP-55 protection consisting of power disconnecting switches with fuses, soft starters, for compressor motors, under/over voltage trip, single phase preventers, communication card which can accept 4-20 mA or 2-10 Vdc analog signal. The COP at AHRI conditions shall not be less than 3.1 and IEER not less than 6.5 . 18HP - Inverter Scroll Compressor Modular VRF ODU

16HP - Inverter Scroll Compressor Modular VRF ODU

22HP - Inverter Scroll Compressor Modular VRF ODU

VRV/VRF Indoor Units (4WAY CASSETTE UNIT) - Supply, Installation, Testing and commissioning of Indoor Cassette units. All the units should be supplied with Cordless remote control and Refrigerant Y joints with fixing arrangements, etc., (Capacity : 3TR)

VRV/VRF Indoor Units (4WAY CASSETTE UNIT) - Supply, Installation, Testing and commissioning of Indoor Cassette units. All the units should be supplied with Cordless remote control and Refrigerant Y joints with fixing arrangements, etc., (Capacity : 2TR)

VRV/VRF Indoor Units (4WAY CASSETTE UNIT) - Supply, Installation, Testing and commissioning of Indoor Cassette units. All the units should be supplied with Cordless remote control and Refrigerant Y joints with fixing arrangements, etc., (Capacity : 4TR)

VRV/VRF Indoor Units (2WAY CASSETTE UNIT) Supply, Installation, Testing and commissioning of Indoor Cassette units. All the units should be supplied with Cordless remote control and Refrigerant Y joints with fixing arrangements, etc., (Capacity : 1.6 TR)

VRV/VRF Indoor Units (1 WAY CASSETTE UNIT) - Supply, Installation, Testing and commissioning of Indoor Cassette units. All the units should be supplied with Cordless remote control and Refrigerant Y joints with fixing arrangements, etc., (Capacity : 1.0 TR)

VRV/VRF Indoor Units (1 WAY CASSETTE UNIT) - Supply, Installation, Testing and commissioning of Indoor Cassette units. All the units should be supplied with Cordless remote control and Refrigerant Y joints with fixing arrangements, etc., (Capacity : 1.32 TR)

VRV/VRF Indoor Units (1 WAY CASSETTE UNIT) - Supply, Installation, Testing and commissioning of Indoor Cassette units. All the units should be supplied with Cordless remote control and Refrigerant Y joints with fixing arrangements, etc., (Capacity : 1.6 TR)

VRV/VRF Indoor Units (Hiwall Unit) - Supply, Installation, Testing and commissioning of HIWALL units. All the units should be supplied with Cordless remote control and Refrigerant Y joints with fixing arrangements, etc., (Capacity : 0.8 TR)

CENTRAL REMOTE CONTROLER FOR VRF / VRV SYSTEM (I-Touch Controller) - 'Supply and erection of Central Remote Controller for controlling the below said parameter of the VRV system. Temperature, change of set temperature, ON-OFF controller ,scheduling and sequencing.enegry consumption. Unit alarm trip status. compressor run status. with BACNET and BMS Compatible. The iTouch is our advanced centralized controller. It can control up to 64 indoor unit groups (128 indoor units). It has independent cool and heat setpoints for occupied and unoccupied conditions. The iTouch Controller provides building owners, facilities/premises managers and maintenance operators refined and energy efficient control of Daikin VRVIII, VRV WIII, VRVIII-S and/or mixed VRVIII/VRV-IIIS/SkyAir indoor units. With its user friendly color icons and scheduling capabilities, this controller makes management of indoor units and other facilities equipment easy. The iTouch Controller is linked directly to the system via a Daikin DIII-Net connection without the need for a PC. Supports centralized control remotely using a PC with a Web browser (Optional).

Supply and erection of Refnut Joints with all accessories

Supply and laying of 50mm dia HDPE PVC pipes for drain with necessary supports and fittings.

Supply and laying of 25mm dia HDPE PVC pipes for drain with necessary supports and fittings.

Copper Piping with Gas and insulation - Supply, Installation, testing and commissioning including vaccumisation and Nitrogen testing of following nominal sizes of soft/ hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing /brazing including accessories, insulated with Nitrile rubber Class-O tubular insulation / with Class-O closed cell elastomeric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquidlines, all accessories asper specifications etc. as required : Gas line with 19 mm thick insulation and Liquid line with 13 mm thick insulation

Supply and erection of Gas line of 41.3 mm with insulation

Supply and erection of Gas line of 36.9 mm with insulation

Supply and erection of Gas line of 28.6 mm with insulation

Supply and erection of Gas line of 22.2 mm with insulation

Supply and erection of Gas line of 19.1 mm with insulation

Supply and erection of Gas line of 15.9 mm with insulation

Supply and erection of Gas line of 12.7 mm with insulation

Supply and erection of Gas line of 9.5 mm with insulation

Supply and erection of Gas line of 6.4 mm with insulation

Supply and filling of R410A Refrigerant Gas

Supply and erection of GI Hot Dip / Powder Coated 16 SWG Perforated type Cable Tray with 150mm width and 50mm height with all the fixing accessories for laying the refrigerant line

Supply, Installation, Testing & Commissioning of Factory fabricated Rectangular GI duct with galvanized sheet steel (GSS) confirming to IS 277 or Al sheets confirming to IS 737. The steel sheet shall be hot dipped galvanized with matt finish with coating of min. 120 GSM of zinc, The sheet thickness shall be as per CPWD specifications , GSS Duct Construction standards must conform to IS 655-2006 & For Factory fabricated duct should follow SMACNA -2005 Standards. 'GSS ducting shall be complete with all relevant accessories like splitters, vanes and Proper jointing (EPDM lining/cleats etc.) shall be done to prevent air leakages. The quoted price shall be inclusive of necessary accessories, Channel supports, Threaded rod,etc. 'Supply, Fabrication and erection of fabricated ducting made up of GI Sheets of 24 Gauge thickness - 0.63 mm

Supply and fixing of extruded aluminum powder coated, supply and return Air Grilles / Diffusers with Volume Control Damper

Supply, Installation of extruded aluminum with powder coated louver or as per OEM requirements complying codes & standards, Fresh Air louver shall have manually operated dampers along with bird screen wire mesh and exhaust air louver shall only have bird screen wire mesh.

Supply,Installation, Testing and Commisioning of Aluminium powder coated Exhaust disc valve with B.F.Damper 150 mm dia

Supply, erection, testing and commissioning of following MS ‘C’ Class Heavy Duty Pipe as per IS 1239 to withstand a developing pressure of 10 kg. / sq.cm including necessary fittings like MS flange of table ‘E’, elbows, reducers, gaskets, bolt, nuts with washers & joints as per standard method of arc welding, including one coat metal primer and two coat Post Office Red painting including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: JINDAL / EQUIVALENT.

150mm nominal dia ( Down comer + Terrace Pump room piping)

100mm nominal dia ( Down comer + Terrace Pump room piping)

80mm dia

65mm dia.

50mm dia.

40mm dia.

32mm dia.

25mm dia.

Wrapping and coating anti-corrosive treatment for the following under ground MS pipe having one coat of anticorrosive metal primer, one layer of asphalt tar tape wound over the MS Pipe as per standard methods as per standard specifications and as directed by the Departmental Officers.

Supply, Erection, Testing and Commissioning of Cast Iron Body Butterfly Isolation Valves (PN:20) with necessary fittings and accessories like flanges, GI bolts, nuts & washers, painting etc. The Valves shall be of Lever operated valves for 150NB and below and gear operated valves for 200NB and above a) 150mm Dia.

Supply, Erection, Testing and Commissioning of Cast Iron Body Butterfly Isolation Valves (PN:20) with necessary fittings and accessories like flanges, GI bolts, nuts & washers, painting etc. The Valves shall be of Lever operated valves for 150NB and below and gear operated valves for 200NB and above a) 100mm Dia.

Supply, Erection, Testing and Commissioning of Cast Iron Body Butterfly Isolation Valves (PN:20) with necessary fittings and accessories like flanges, GI bolts, nuts & washers, painting etc. The Valves shall be of Lever operated valves for 150NB and below and gear operated valves for 200NB and above a) 50mm Dia.

Supply, Erection, Testing and Commissioning of Cast Iron Body Butterfly Isolation Valves (PN:20) with necessary fittings and accessories like flanges, GI bolts, nuts & washers, painting etc. The Valves shall be of Lever operated valves for 150NB and below and gear operated valves for 200NB and above a) 80mm Dia.

Supply and fixing of Fire fighting application oblique type stainless steel Hydrant Valve of size 63mm dia with oblique type instantaneous coupling with rotating wheel to open and close the valve including MS flange of table “E”, bolts & nuts with washer as per IS 5290 at ring main around the building and wet riser inside the building including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT.

Supply, and fixing in position of Fire Fighting Application Hose of 63mm dia of 15 metres length binded by copper wire with 63mm dia stainless steel male and female instantaneous fire fighting special coupling as per IS 901 as directed by the Departmental Officers. Near every hydrant points including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR/ LIFE GUARD / SAFE GUARD / EQUIVALENT.

Supply, and fixing in position of Fire Fighting Application 63mm dia stainless steel short length Branch Pipe with hexagonal type spray nozzle of 15mm (or) 20mm jet bore. Near every hydrant points including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: OMEX /KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT.

Supply of Fire Fighting Application MS Hose Box to keep two number of hoses and 1 No. of branch pipe with nozzle having proper glass window type double door with universe open key, painted inside white and outside Post Office Red. Near every hydrant point including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT.

Supply, installation of Fire Fighting Application 180 degree swinging type, hose reel drum with 20mm dia braided thermoplastic hose of 30 metres long, so as to extend to necessary distance by self rolling spindle wheel including necessary 20mm dia ball valve and open and close spray nozzle, warm clip, etc., as per the standard pattern of any reputed make at every floor nearer to hydrant valve, including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary., etc., complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT.

Supply, erection, testing and commissioning of Air Release Valve of 20mm dia, so as to release airlock in 100mm dia MS pipe at top most wet riser, including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: KARTAR / EQUIVALENT.

Supply and installation of RCC HUME Pipe of 300mm dia, NP2 class with collars for road / below floor crossing of fire pipe. The rate shall include excavation, soil leveling for bed and ends shall be closed with brick masonry, work as directed by site Engineer.

Supplying, fabricating, structural steel supports such as MS channels, angles, flats, rods as required at site with anchor fasteners, clamps, threaded rods, nuts, bolts, washers etc. complete with painting for pipe support.

Construction of Concrete Pedestal supports including M.S. Supports - 900 x 300 x 300 mm ( For supporting above Ground for Fire pipes )

Supply, erection, testing and commissioning of Fire Fighting Application Horizontal Centrifugal Type Pump Rated for 2280 LPM at 70 metres head with Electrical Motor of 60 HP of 415 volt 3 phase connection complete with base plate and accessories. (Make: Kirloskar or Equivalent). The rate inclusive of necessary vibration, bad mounting etc., as per standard method as directed by the Deparmental Officer

Supply, installation, testing and commissioning of Diesel Engine Driven Main Fire Pump suitable for automatic operation and consisting of following and complete in all respects as required. a. End suction, top discharge centrifugal pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal to ensure a minimum pressure of 3.5 kg. / sq. cm at highest and farthest outlet at specified flow of 2280 LPM at 70m head conforming to IS 1520. b. 68 BHP, 1500 RPM water cooled with radiator, diesel engine conforming to relevant BS & IS standard complete. Auto starting mechanism, 12 volts / 24 volts electric starting equipment like self motor, dyanamo, solenoid switches etc. c. 110 litres capacity diesel tank mounted over stand fabricated using 25mm x 25mm x 6mm size MS angle, providing with level indicator, inlet port, outlet port, drain port and diesel return line port and fuel pre-filter, after filter etc. (Make: Kirloskar / Equivalent). d. Exhaust system having flexible metallic mufler, 100mm dia MS heavy pipe extended upto 1m, outside pump house duly insulated with 50mm thick glass wool with 1mm thick aluminium sheet cladding, residential silencer with necessory MS support arrangements from wall or ceiling as per site condition. e. Dash board consisting the instruments like temperature gauge, galvano type DC Ammeter, lubricant oil pressure gauge, ignition switch, emergency stop and all otherprotection equipment as per specification, stop seleneid for auto stop in the event of fault with audio indications, painted with post office red colour etc., as required. f. 12 V / 24 V storage battery, maintenance free tape, 180 AH rating, MS fabricated common base plate, coupling guard, foundation bolts etc., as required.g. Positioning the diesel engine driven fire pump over cement concrete foundation using suitable size anti-vibration mounting arrangement.All works carried out as per standard methods and as instructed by the manufacturer and as directed by the Departmental Officers. (Make: Kirloskar / Equivalent)

Supply, erection, testing and commissioning Mono Block type Fire Fighting Pressurisation Pump of 180 LPM 110 metres head at 10 HP with suitable base frame including necessary vibration bad mounting etc., including conveying, fixing and incidental charges., etc., complete as per standard specification and as directed by the Departmental Officers. (Make: Kirloskar / Equivalent)

Supply and laying of following sizes of Armoured Aluminium / Copper Cables for electrical motor, control panel, pressure switch, jockey motor etc., all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: POLYCAB / PARACON / FINOLEX / EQUIVALENT.

3 core 185 sq.mm. armoured aluminium cable

3 core 10 sq.mm. armoured copper cable

10 core 2.5 sq.mm. armoured copper cable

2 core 2.5 sq.mm. armoured copper cable

Earthing arrangements with GI Earth Plate including charcoal and salt with necessary excavation in all soils and to full depth as may be required and masonry work, re-filling the sides of foundation with excavated earth as per the standard specification and as directed by the Departmental Officers.

Supply and laying of 25mm X 6mm GI strip

Supply and erection of GI Hot Dip / Powder Coated 16 SWG Perforated type Cable Tray with 150mm width and 50mm height with all the fixing accessories for laying the refrigerant line

Supplying, installing, testing and commissioning of Heavy grade G.I. Pipes confirming to IS :1239 part - I with butt welded specials confirming to IS:1239 part - II, such as Tees, elbows, check nuts, unions, flanges, nipplesetc. Including cutting,painting Welding, fixing in / on walls, ceiling by using suitable supports, including pipes travelling under ground etc, as per drawings - a) 200mm Nominal dia

150mm Nominal dia

100mm Nominal dia

80mm Nominal dia

50mm Nominal dia

25mm Nominal dia

Exhuast pipe for Diesel engine of with mineral wool insulation with aluminum sheet.- M.S. 'B' class pipe - 150 mm dia

Supply, erection, testing and commissioning of Cast iron body and Gun metal or stainless steel internal Non-return valve of following sizes to control one way flow of water to be installed pump room at delivery line and near overhead tank at terrace level near to jockey pump and motor including necessary MS flange of table ‘E’, gaskets, bolts & nuts, etc. as per IS 5312 including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. - 150mm Dia.

100mm dia

80mm dia

Supplying, fabricating, structural steel supports such as MS channels, angles, flats, rods as required at site with anchor fasteners, clamps, threaded rods, nuts, bolts, washers etc. complete with painting for pipe support.

Supplying, Installing, testing and commissioning CI Butterfly valves/Gate Valve( PN 20) steam rising operated type with required flanges, nuts, bolts etc. complete. a) 200mm Dia.

150 mm nominal dia

100 mm nominal dia

80mm nominal dia

50 mm nominal dia

Supplying, installing, testing and commissioning of Gun metal chrome finished Ball valves with fittings of screwed end type. - 25mm Dia.

Supplying, installing, testing and commissioning of Gun metal chrome finished Ball valves with fittings of screwed end type. - 15mm Dia.

Supplying, installing, testing and commissioning of C. I. Flanged FOOT valve with SS mesh,suitable flanges, nuts, bolts, gaskets etc. complete. (PN 20) a) 200mm NB

Supplying, installing, testing and commissioning of C. I. Flanged FOOT valve with SS mesh,suitable flanges, nuts, bolts, gaskets etc. complete. (PN 20) a) 100mm NB

Supply, Installation, Testing & Commissioning of Flow meter (150mm) size with required flanges, nuts, bolts etc. complete.

Providing, fixing, testing and commissioning of air vessel (size 450 mm dia and 1500mm HOS) fabricated from 10 mm thick shell & dished end 12 mm thick M.S. Plate for pressurization of hydrant/ sprinkler/water curtain system complete. 50 dia. socket for drain, 65 dia. socket for inlet, 25 dia. sockets for pressure relief valve, pressure switches and pressure gauges, 450 mm dia manholes, M.S legs, epoxy painted from inside and enamel paint from outside after grit blasting complete.

Supply and providing 1000 litres capacity Priming Tank made up of PVC. Make: SINTEX / EQUIVALENT

Supply, Erection, Testing and Commissioning of Metallic-Rubber bellow flexible connections of suitable pressure rating to be installed at equipments suction and discharge.with necessary fittings and accessories like flanges, GI bolts, nuts & washers, painting etc. a) 200mm NB

Supply, Installation, Testing & Commissioning of Puddle Flange - a) 200mm Dia.

Supply, Installation, Testing & Commissioning of Puddle Flange - a) 150mm Dia.

Supply, erection, testing and commissioning of Fire Fighting 4 Way Fire Brigade Inlet with necessary gun metal 63mm dia non return spring shutter arrangements, so that to control one way flow at the time of emergency water supply by fire and rescue service fire engine entry including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: KIARTAR / OMEX / EQUIVALENT

Supply, erection, testing and commissioning of Fire Fighting 2 Way Fire Brigade Inlet with necessary gun metal 63mm dia non-return spring shutter arrangements so that to control one way flow at the time of emergency water supply by fire and rescue service fire engine entry including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary., etc., complete as per standard specification and as directed by the Departmental Officers. (Make: KIARTAR / OMEX / EQUIVALENT)

Supplying, installing, testing and commissioning of Gun metal chrome finished Ball valves with fittings of screwed end type. A) 25mm dia.

Supplying, installing, testing and commissioning of `Y' - Type Strainer with Flanged ends - 100mm Dia.

Supply, erection, testing and commissioning of suitable Pressure Switch of reputed make including necessary valves, couplings, etc., connected with electrical main control panel and setup at proper differential so as to auto start and auto stop the electrical motor, jockey motor including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary, etc., completed as per standard specification and as directed by the Departmental Officers. Make: DONFOSS / INDFOSS / ISI MAKE / EQUIVALENT.

Supply, erection, testing and commissioning of Pressure Gauge with 0 to 14 kg. range of reputed make with necessary valve, milling thread MS coupling fixed at delivery pipe line in pump house to read the developing pressure including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: H-GURU / ISI MAKE / EQUIVALENT.

Supply and fixing of Puddle Flange suitable for 100mm dia at Terrace tank with unions etc., complete.

Supplying, Installing, testing and commissioning of PN 16 lever operated Butterfly valve with required flanges, nuts, bolts etc., complete - 150mm dia.

Supplying, Installing, testing and commissioning of PN 16 lever operated Butterfly valve with required flanges, nuts, bolts etc., complete - 100mm dia.

Supplying, Installing, testing and commissioning of PN 16 lever operated Butterfly valve with required flanges, nuts, bolts etc., complete - 50mm dia.

Supply, Installation, Testing & Commissioning of Flow Switch with 2 NO and 2 NC contacts with necessary nipple and other fittings - 100mm dia.

Supply and fixing nominal bore quartized bulb type sprinkler bulb 68 Deg C fast response pendent type including GI collar for each sprinkler bulb, mounted in MS pipe line using suitable size MS threaded coupling, thread, shellac etc., as per standard methods and including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary, etc., complete as per standard specification and as directed by the Departmental Officers. Type: K-80 Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT.

Supply, Installation, Testing & Commissioning of Dial type pressure gauge Industrial type) with necessary nipple & other fittings - 150mm Dia.

Supply, Installation, Testing & Commissioning of Dial type pressure gauge Industrial type) with necessary nipple & other fittings - 100mm Dia.

Supply, Installation, Testing & Commissioning of 25mm Ball valve with necessary nipple and other fittings

Supply, Installation, Testing & Commissioning of150mm dia sprinkler alarm gang valve with necessary fittings

Supply, Installing, testing and commissioning of Stainless Steel Corrugated Flexible Braided Pipe (Hose) for dropping sprinklers below false ceiling. Pipe shall be 16 bar pressure rating and 1500mm long, 25mm dia with union / reducer, collar, clamps, etc. It shall have UL listed and FM approved.

Supplying and installing of approved type Rosette Plates (Recessed Type in Two Pieces) for sprinklers below false ceiling area. The Rosette shall be fabricated by MS plate of 2mm thick and the finish shall be powder coated and colour, as directed by the Departmental Officers.

Supply and fixing of Hand held Fire Extinguisher - CO2 - 4.5 Kg with suitable Metal Floor stand MS fabricated painted in black colour

Supply and fixing of stored pressure ABC (Mono Ammonium Phosphate) Powder Type Fire Extinguisher of 6 kg. capacity as per IS:15683 with pressure gauge, discharge hose & control nozzle, wall mounting bracket, safety clip etc., including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary etc, complete as per standard specification and as directed by the Departmental Officers. Make: EXCELLENT / SAFETY FIRST / EQUIVALENT

Supply and fixing of EMERGENCY/FIRE EXIT (450mmx150mm double side)

Supply and fixing of FIRE EXTINGUISHER (100mmx150mm single side)

Supply and fixing of "EXIT " (400mmx150mm double side)

Supply and fixing of "MANUAL CALL POINT" (100mmx150mm single side)

Supply and fixing of "EVACUATION PLAN with AUTO GLOW" in A2

Supply, Installation, Testing & Commissioning of Addressable Fire Alarm Control Panel consists of display board which will have 160 Character Display with Touch key pad, Mother board 32 Bit Processor, In-built RS-485 Networking Circuit for peer to peer networking, In-built USB 2.0 Port, Loop Card having 254 devices of both detectors and modules in a single line circuit, SLC supports both Class A and Class B wiring Approval: UL Listed a) Two Loop Panel

Supply, Installation, Testing & Commissioning of Addressable Detectors with base with Binary coded address setting. Dual LED’s for 360° visibility a) Multi Sensor - Heat Cum Smoke detector

Supply, Installation, Testing & Commissioning of Addressable Heat detector

Supply, Installation, Testing & Commissioning of Addressable Addressable Manual Call Point - Resettable type - with back box with Binary coded address setting with Status LED for 360° visibility.

Supply, Installation, Testing & Commissioning of Conventional type Horn / Strobe wall mounted type rated at 90 dBA @ 1m for Audible annunciation and 15cd minimum flashing at 1 Hz for visual indication.

Supply, Installation, Testing & Commissioning of Fault Isolator Module capable of monitoring shorted loop circuit and automatically restore communications

Supply, Installation, Testing & Commissioning of Response indicator for all detectors located above false ceiling.

Supply, Installation, Testing & Commissioning of POWER SUPPLY : 24VDC Power Supply with 5 amp rating, having LED indications for Power supply ON,battery Fail,Battery Charging,battery back up etc.

Supply, Installation, Testing & Commissioning of 2 core x 1.5 sq.mm Red colour twisted pair shielded multi strand ATC armoured FRLS cable

Supply and Erection of 5 13 PersonPassenger Lift G+2 with M/C room, Speed 1.5 m/s with Stainless Steel Panels, Disable friendly, microprocessor based controller, VVVF drive, Fire rated doors and ARD

Supply and Erection 50 inches 4K Ultra HD Smart LED Google TV with the following specifications. Colour: Black, TV Display: Refresh Rate:60 Hz, Screen Resolution: 3840 x 2160 - Ultra HD, Screen Size (Diagonal): 126 cm - 50 inch HDMI & USB Ports, No of HDMI Ports: 3 No. of USB Ports: 2, USB: Yes, TV Audio Related, Rated Speaker Output Power (RMS):20 Watt, TV Connectivity Choices, Additional Connectivity Apple Airplay, Apple Homekit, Alexa, Gesture Control: Yes TV Placement Wall Mounted, Depth (without stand): 7.7 cm Height (without stand): 66.2 cm, Width (Without Stand): 112.7 cm Power Details, Power Consumption: 115 Watt, Power Supply: 240 V Additional Features, Open Baffle Speaker, Full Range (Bass Reflex ) x 2 , Dolby Audio, Clear Phase Google TV, Watchlist, Ok Google, Google Play, Chromecast, Built In Mic Variable Refresh Rate and ALLM (Auto Low Latency Mode) Live Colour, Motion Flow. Brand :SONY or Equivalent

SRI ANNAMAAR AND CO (BID ID -1271266)

sivaparameswari engineering construction and co (BID ID -1271794)