Adar-Bardiha-Obra and Sukhnadi Rural Water Supply Scheme under Drinking Water Sanitation Division Garhwa on turnkey basis for the year 2020-21

Amount

Elevated Service Reservoir

Doing Geotechnical survey, Collecting field data, designing, getting it approved by competent authorityand Providing all labours and equipment for designing & construction of ESR all complete job. (Please refer to Section 5,Sl. 2.8 of SBD)

(i) ESR 7.60 lakh Litre Capacity. Staging ht.22.00m

(ii) ESR 7.10 lakh Litre Capacity. Staging ht.17.00m

Water Treatment Plant

Doing Geotechnical survey, Collecting field data, designing, getting it approved by competent authorityand Providing all labours and necessary equipment for designing & construction of Uncononventional WTP of 5.50 MLD capacity. With all complete job. (Please refer to Section 5,Sl. 2.3 of SBD)

Construction of R.CC intake well cum pump

Doing Geotechnical survey, Collecting field data, designing aesthetically, getting it approved by competent authority and Construction of 6.00 m dia and Total height of IntakeWell =15.0 M [(9.71 M below River Bed level ,2.34M bed to floor and floor level of pump house is 6.14M above river bed level and Roof level of pump House is 5.00 M above floor of P.H) cum Raw Water Pump House(Please refer to Section 5,Sl. 2.1 of SBD).

Earthwork in excavation of foundation trenches of toe wall,spillway,head ragulator,outlet,intake well etc. as per designed section in all kinds of soil, including moorum soil, soil muxed with kanker, pebbles and boulders up to 300 mm size and disposal of the same (beyond 50 M away from the toe of the dam base in the country side) with in initial lead of 1.5 M all lifts as per specification and direction of E/I.

Lift 14.71 m to 13.21 m

Lift 13.21 m to 12.21m

Lift 12.21 m to 11.21m

Lift 11.21 m to 10.21m

Earthwork in excavation of cut off trenches as per designed section in soft rock or ordinary rock (vide classification of soil item C) with disposal of spoil (beyond 50 M away from the toe of dam within 1 km with II lifts by truck including loading,unloading, construction and maintenance of haul road etc as per specification & direction of E/I. (soft rock where blasting is not required and approved by the concerned chief Engineer)( 0% of excavation)

Lift 10.21 m to 9.71 M

Lift 9.71 m to 9.21 M

Lift 9.21 m to 8.71 M

Lift 8.71 m to 8.21 M

Lift 8.21 m to 7.70 M

Providing and laying PCC or RCC M 150 with nominal mix (1 : 2 : 4) in various components of barrage foundation with approved quality of 20 mm graded coarse aggregated of required grade as per design and aproved quality of sand of requisite F.M. (2.5 to 3.0) washed and screened excluding cost of shuttering or from work as well of reinforcement, its cutting bending, binding and placing but including necessary tools and plants and vibrating, curing, royalty all taxes etc all complete job as per specification and direction of E/I.

Providing RCC M 300 with nominal mix (1:1:2) in various components of barrage foundation with approved quality of 20 mm graded coarse aggregated of required grade as per design and aproved quality of sand of requisite F.M. (2.5 to 3.0) washed and screened excluding cost of shuttering or from work as well of reinforcement, its cutting bending, binding and placing but including necessary tools and plants and vibrating, curing, royalty all taxes etc all complete job as per specification and direction of E/I.

Providing and laying in situ Cement concrete of trap/ granite /quartzite /gnesiss metal for RCC work as per details drawing and design or as directed by engineer-in -charge including normal normal dewatering Plywood Formwork , bully steel prop-ups , compaction, finishing the formed surfaces with CM (1:3) of sufficient min. thickness to give a smooth and even surface wherever necessary or roughing if a special finish is to be provided and curing etc.cmplete (by weight batching and mix design for M-25 and M-30 only) (Exculding M.S or Tor reinforcement.)

Vertical wall of Intake well

Providing and laying in situ Cement concrete of trap/ granite /quartzite /gnesiss metal for RCC work as per details drawing and design or as directed by engineer-in -charge including normal normal dewatering Plywood Formwork , bully steel prop-ups , compaction, finishing the formed surfaces with CM (1:3) of sufficient min. thickness to give a smooth and even surface wherever necessary or roughing if a special finish is to be provided and curing etc.cmplete (by weight batching and mix design for M-25 and M-30 only) (Exculding M.S or Tor reinforcement.)

Providing and laying in situ Cement concrete of trap/ granite /quartzite /gnesiss metal for RCC work as per details drawing and design or as directed by engineer-in -charge including normal normal dewatering Plywood Formwork , bully steel prop-ups , compaction, finishing the formed surfaces with CM (1:3) of sufficient min. thickness to give a smooth and even surface wherever necessary or roughing if a special finish is to be provided and curing etc.cmplete (by weight batching and mix design for M-25 and M-30 only)(Exculding M.S or Tor reinforcement.)

Providing RCC M 250 with nominal mix of in columns with approved quality of stone chips 20 mm to 6 mm size graded and cleaned coarse sand of FM 2.5 to 3 including screening, centering, shuttering, mixing cement concrete in mixer and placing in position ,vibrating,striking,curing(but excluding the cost of reinforcement,taxes,and royality all complete as per building specification and direction of E/I)

Providing RCC M 200 with nominal mix of (1:1:5:3) in band at lintel level with approved quality of stone chips 20 mm to 6 mm size graded and cleaned coarse sand of FM 2.5 to 3 including screening, centering, shuttering, mixing cement concrete in mixer and placing in position ,vibrating,striking,curing(but excluding the cost of reinforcement,taxes,and royality all complete as per building specification and direction of E/I)

Providing RCC M 200 with nominal mix of (1:1:5:3) in roof slab with approved quality of stone chips 20 mm to 6 mm size graded and cleaned coarse sand of FM 2.5 to 3 including screening, centering, shuttering, mixing cement concrete in mixer and placing in position ,vibrating,striking,curing(but excluding the cost of reinforcement,taxes,and royality all complete as per building specification and direction of E/I)

Providing 63 mm average thickness RCC M 200 with nominal mix of (1:1:5:3) in chhjja with approved quality of stone chips 20 mm to 6 mm size graded and cleaned coarse sand of FM 2.5 to 3 including screening, centering, shuttering, mixing cement concrete in mixer and placing in position ,vibrating,striking,6 mm cement plaster (1:4) in ceiling and side of chhjja with sand of FM 1.5 , curing(but excluding the cost of reinforcement,taxes,and royality all complete as per building specification and direction of E/I)

Providing MS reinforcemnet(tor steel) as per approved design and drawing,removal of rust, cutting, bending and binding including supplying annealed wire, placing MS rods in position all complete as per specification and direction of E/I(1.5 % of RCC quantity)

Brick work in designation 75A with CM 1:6 in superstructure with approved quality of coarse sand of requiite FM(2.5 to 3.0) washed and screened with raking out joints to 12 mm depth curing, scaffolding and its removal whereever required including royality and all taxes etc. complete job as per specifiction and direction of E/I

Supplyiing fitting & fixing M.S Grill made of 20 x 6 mm MS flat as per approved design & drawing in window 3 x 1.2 x 2.0 x 7.20 m² @ 40kg P/M²

Supplyig, fitting and fixing fully glazed steel doors,windows or ventilation of standard rolled "Z" and mullion steel sections and size as per IS-1038 joints met and welded with 100 x 16 x 3 mm MS lugs fixed in cement concrete (1:2:4) blocks 15 x 10 x 10 cm size including cost of oxidised iron fittings, with hinges handle per steps, catch springs,, 3mm thick plain glass panes with aluminium beads and inner frame fixed with ligs with 20 mm long 6.3 mm GI counter sunk mchine screw and nuts and applying a coat of red lead paint carrige to work site hoisting and placing in position in all storys and taxes all complete as per building specificatio as direction of E/I

Supplying and fixing rolling shutters of approved,made of required size MS lathes interlocked together through their entire length and jointed together at ends by end locks mounted on especially designed pipe shafts with brackets,side guides and arrangement for inside and outside locking with pull and push operation complete,including the cost of providng and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wires of adequate strength confirming to IS:4454 -part 1 and MS top cover of required thickness for rolling shutters 80 x 1.25 mm MS laths with 1.25 mm thick top cover

providing and fixing ball bearing for rolling shutter

Providing 12 mm thick cement plaster (1:6) with approved quality of sand of requisite FM 1.5 washed and screnned including curing , scaffolding wwhereever required and its removal ,royalty and all taxes etc complete job as per specification and direction of E/I

Providing 12 mm thick water proof cement plaster (1:3) with approved quality of sand of requisite FM 1.5 with 5% cico or any other approved water proofing compound including screnning including curing , scaffolding and all taxes etc complete job as per specification and direction of E/I

Providing 06 mm thick cement plaster (1:4) in ceiling of P/H and intake well with clean coarse sand of requisite FM 1.5 including screnning including curing , scaffolding and all taxes etc complete job as per specification and direction of E/I

Providing two coats of snowcem of approved shade and make over a coat of cement primer on new surface including preparing the plastered surface smooth with sand paper ,scaffolding,curing, and taxes all complete as per building specification and direction of E/I

Providing two coats of painting with ready paint of approved shade & make over steel surface including cleaning the surface throughtly scaffolding and taxs all complete as building specification and direction of E/I.

RS joist 250 x 125 (Grade A) size fitting and fixing in position including cutting to required in shape and size its carriaage applying a primer coat of red lead paaint etc all complete as per building specificaation and direction of E/I.

Supplying laying fitting and fixing 25 mm dia G.I pipes of medium class railling well lengths of approvided make is three rows each passing through 50x50x6 mm angle at 1.5 m c/c and additional post of every snowcem add painting 3 coats full paint over. one coat of aaticornssive paint of approved colours add shade including cost of all labour , transporting , beats to curve shape etc. all complete job.

Providing and fixing in position CI type dapuri steps of 22 mm dia MS bar steps with proper anchorage etc and providing and applying three coats of anti corrosive paint etc complete as per directed by E/I

Providing and fixing M.S sluice gates in position as per detailed drawing and specification including cost of all materials,labour,opearting pedestal, connecting rod,painting with three coats of anti corrosive paint, etc complete as directed by engineering in charge.

Providing and fixing in position C.I./M.S rose pieces in intake wells including cost of all materials and labour, painting with three coats of anti-corrosive oil paint, etc.complete as directed by engineer-in-charge.

Carriage of construction materials to work site including loading, unloading & stacking etc. all complete.

Cement 30 KM lead

Steel 30 KM lead

Sand 30 KM lead

Bricks 30 KM lead

Stone/Stone Chips 30 KM lead

Construction of Gang Way 55 M long and 3.00 M wide

Doing Geotechnical survey, Collecting field data, designing, getting it approved by competent authorityand Providing all labours and necessary equipment for designing & construction of Gang Way (Please refer to Section 5,Sl. 2.2 of SBD).

Earthwork in excavation of foundation trenches as per designed section in all kinds of soil, including moorum soil, soil muxed with kanker, pebbles and boulders up to 300 mm size and disposal of the same (beyond 50 M away from the toe of the dam base in the country side) with in initial lead of 1.5 M all lifts as per specification and direction of E/I

Lift 0.00m to 1.50m

Lift 1.50m to 2.00m

Providing PCC M 150 with nominal mix (1 : 2 : 4) in various components of barrage foundation with approved quality of 20 mm graded coarse aggregated of required grade as per design and aproved quality of sand of requisite F.M. (2.5 to 3.0) washed and screened excluding cost of shuttering or from work as well of reinforcement, its cutting bending, binding and placing but including necessary tools and plants and vibrating, curing, royalty all taxes etc all complete job as per specification and direction of E/I.

Providing and laying in situ cement concrete of trap / granite/ quartzite/ gneiss metal for RCC work in foundation like raft , grillage, strip foundation and footing of RCC columns and steel stanchions including normal dewatering , plywood from bully / steel propups compaction, finishing and curing etc. complete .(by weight batching and mix design for M-25 and M-30 only. (excluding M.S or Tor in RCC M-25) M-300

Providing and laying in situ cement concrete of trap / granite/ quartzite/ gneiss metal for RCC work in foundation like raft , grillage, strip foundation and footing of RCC columns and steel stanchions including normal dewatering , plywood from bully / steel propups compaction, finishing and curing etc. complete .(by weight batching and mix design for M-25 and M-30 only. (excluding M.S or Tor in RCC M-25)

Providing and laying in situ cement concrete of trap / granite/ quartzite/ gneiss metal for RCC work in foundation like raft , grillage, strip foundation and footing of RCC columns and steel stanchions including normal dewatering , plywood from bully / steel propups compaction, finishing and curing etc. complete .(by weight batching and mix design for M-25 and M-30 only. (excluding M.S or Tor in RCC M-25)

Providing RCC M- 200 with nominal mix (1:1.5:3) in roof slab nominal mix in foundation and plinth, plinth beam ,band etc. with approved quality of stone chips 20 mm to 6 0 mm size graded and clean coarse sand of F.M 2.5 to 3.0 including screening ,shuttering mixxing cement concrete , in mixter and placeing in position , vibration, strinking curing (but excluding the cost of reinforcement taxes in roylaty all complete job as per building specification and direction E/I

Providing MS reinforcemnet(tor steel) as per approved design and drawing,removal of rust, cutting, bending and binding including supplying annealed wire, placing MS rods in position all complete as per specification and direction of E/I

Providing 12 mm thick cement plaster(1:4) with approved quality of sand of requisite FM(2.5 to 3.0) washed and screened including curing,scaffolding whereever required and its removal,royalty and all taxes etc complete job as per specification and direction of E/I

Providing 6 mm thick cement plaster(1:4) in ceiling with clean coarse sand of FM-1.5 including curing with all leads & liftss caffolding taxes & royality all complete as per specification and direction of E/I

Providing and fixing G.I. pipe railing having 1.0 M height consisting 50 x 50 x 6 mm thick M.S. angles as verticals at 1.5 M c/c and additional posts at every corner with 3 rows of 25 mm dia G.I. pipes of medium class variety as horizontal and painting 3 coats of oil paint over 1 coat of anticorrosive paint of approved colour and shade including cost of all labour, transporting bends to curved shape, etc. complete.

Providing two coats of snowcem of approved shade and make over a coat of cement primer on new surface including preparing the plastered surface smooth with sand paper ,scaffolding,curing, and taxes all complete as per building specification and direction of E/I

Carriage of materials from divisional store or kiln site or quarry site to work site including contract profit, loading, unloading, transportation, etc. all complete.

Cement 30 KM lead

Steel 30 KM lead

Sand 30 KM lead

Stone/Stone Chips 30 KM lead

Coffer Dam

Providing, construction coffer dam in river basin/dam storages as per type design including excavation,filling the middle portion with B.C. soil (in gunny bags if required ). Providing impervious/semimpervious materials on both side of B.C. (in gunny bags if required ) including ramming,compacting to satisfaction of Engineer-in-charge,till the completion of works and disposing off material as directed by the Engineer-in-charge.

(a) For Gangway

(b) For Intake Well

Dewatering the excavate d trenches and pools of water in the building trenches/pipeline trenches,well works by using pumps and other devices including disposing off water to safe distance as directed by Engineer-in-Charge (including cost of machinery, labour, fuel etc Complete)

(a) For Gangway

(b) For Intake Well

Mechanical & Electrical Work at Intake well

Supply, installation, testing and commisssioning of vertical turbine pumpsets with allied equipment as under (Please refer to Section 5,Sl. 2.4 & 2.6 of SBD)

Supplying, Installation and commissioning of Horizontal split casing centrifugal pump set of KIRLOSKAR / WPIL / Matter and Platt make capable of discharge against required head and mounted of common base plate coupled with TEFC squirrel cage IE3 induction motor (As per IS 12615) of KIRLOSKAR/SIEMENS/CROMPTON/ABB/ Marathon make operated on 415 volt 10%, 3 phase 50 Hz A.C. supply having speed 1500 rpm including cost of supplying fitting and fixing of all required accessories such as D.I. D/F special sluice valve, N.R. valve, foot valve ISI maked and D.I. D/F pipe of suitable size and length as required for suction and delivery main, common header, etc. (Contractor will once again have to check the design of motor, Pump & get it approved by the Deptt) (Pump & Motor).Discharge-1905 LPM Head=100 m (2W+1S)

Supply, installation and commissioning of power control cum distribution cubical panel board, made of 2 mm thick MS, sheet of suitable size , dust and vermin proof, consisting of following accessories

a) Incoming feeder-500A, 415V 4P MCCB thermal release range adjustable and breaking capctity with rotary operating mechanism handle ofL&T/SIEMENS/HAVELLS/HPL/ Schneider/ C&S make - 1 no.

b) Fully automatic star delta starter to operate 75 HP induction motor working on 415V, 3phase, 50 Hz with no volt coil, over load element, ON-OFF push buttons, with necessary materials and connected to supply, etc- 3 nos.

c) Bus bar- 4 pole 500 amp. Copper strip bus enclosed in MS sheets etc all completed.

f) Indicating lamp LED/L&T/SIEMENS make in red, yellow and green colour- 1 Sets

g) 200A, 415V TP MCCB thermal release range adjustable and breaking capctity with rotary operating mechanism handle of L&T/ Schneider make for light - 4 nos. for lightning & other loads.

h) Outgoing feeder 32A,63A, 100A & 415V TP MCCB thermal release range adjustable and breaking capctity with rotary operating mechanism handle ofL&T/SIEMENS/ Schneider make - 4 nos.

i) Panel should be duly painted with two coats super enameled paint of approved colour, one coat red oxide primer and internally wired with suitable size of copper wire including Protection Relay, ELCB, RCCB, other Protection units, cooling & insulation pads all complete as per site requirement and IE rules. including capacitor banks (APFC) for power factor, correction with all complete materials and acessories.

Supply, installation and commissioning with Earthing as per analysis with all materials as per IS-3043 for each motor.

Cost of 240 Sq mm x 3.5 core 1.1 KV Grade stranded aluminium conductor PVC insulated PVC sheathed armoured cable including laying on wall or on floor as and where required etc. all complete

Cost of construction of 50 sq mm x 3 core unarmoured copper conductor PVC insuated PVC sheathed 1.1 KV grade cable including laying on wall or on the floor as and where required etc. all complete

Cost of construction of DP structure for transformer, supplying and erecting PSC pole , top bracket channel, back clamp, 11KV disc insulator with hardware, earthing set complete. MS nut and bolts, MS inbuilt lightning arrester ,MS angle, GI wire , clamp for transformere base, top channel, AB switch, HG & do fuse, stay set etc. all complete job, 11 kv lightning arrster as per the site requirement and as per the direction of E/I & IE rules including..

Cost of providing electric wiring inside and outside the pump house for lighting including cost of lamp of 250/400W, switches etc all complete as per the instruction of E/I.

Supply and installation of 1.6mm thick double door sheet steel enclosed lighting distribution board having 32A 30mA 4P ELCB as incomer and 9 nos. 6-20A 10kA SP MCB as outgoing feeders

Supply and installation of servo controlled 200 KVA air cooled 3-phase Automatic voltage stabiliser with input 270-460V and output 415V +/-1%, 3-Ph, 50Hz, Cu woundtransformer air cooled, etc. all complete as per IE Rule and site requirement

Supply, delivery and installation of Fire Extinguisher ABC Type 4.5 kg

Supply, delivery and installation of First aid box with gloves, scissors, adhesive plaster, sterilising solution etc.

Cost of supplying triple spur gear type chain pulley block of 1 ton lifting capacity with 6 m lift complete with load chain & hand chain suitable for above lift, tested to 50% over loadas per IS 3832 carrying ISI mark etc. all complete for site requirement

(Mechanical & Electrical Part at WTP)

Supply, installation, testing and commisssioning of horizontal casing centrifugal pumpsets with alied equipment as (Please refer to Section 5,Sl. 2.5 & 2.6 of SBD)

Supplying, Installation and commissioning of Horizontal split casing centrifugal pump set of KIRLOSKAR / WPIL / Matter and Platt make capable for suitable discharge against total head and mounted of common base plate coupled with TEFC squirrel cage IE3 induction motor (As per IS 12615) of KIRLOSKAR/SIEMENS/CROMPTON/ABB/ Marathon make operated on 415 volt 10%, 3 phase 50 Hz A.C. supply having speed 1450 rpm including cost of supplying fitting and fixing of all required accessories such as D.I. D/F special sluice valve, N.R. valve, foot valve ISI maked and D.I. D/F pipe of suitable size and length as required for suction and delivery main, common header, Pcc foundation,etc all complete with required material & acessories etc. (Contractor will once again have to check the design of motor, Pump & get it approved by the Deptt) (Pump & Motor).

Discharge:- 1905 LPM; Head:-74 m (2W+1S)= 3 no. of pump set

Supply, installation and commissioning of power control cum distribution cubical panel board, made of 2 mm thick MS, sheet of suitable size , dust and vermin proof, consisting of following accessories

a) Incoming feeder-500A, 415V 4P MCCB thermal release range adjustable and breaking capctity with rotary operating mechanism handle ofL&T/SIEMENS/HAVELLS/HPL/ Schneider/ C&S make - 1 no.

b) Fully automatic star delta starter to operate 60 HP induction motor working on 415V, 3phase, 50 Hz with no volt coil, over load element, ON-OFF push buttons, with necessary materials and connected to supply, etc- 3 nos.

c) Bus bar- 4 pole 500 amp. Copper strip bus enclosed in MS sheets etc all completed.

f) Indicating lamp LED/L&T/SIEMENS make in red, yellow and green colour- 1 Sets

g) 100A, 32A 63A, 415V TP MCCB thermal release range adjustable and breaking capctity with rotary operating mechanism handle of L&T/ Schneider make for light - 4 nos. for lightning & other loads.

h) Outgoing feeder 60A, 415V TP MCCB thermal release range adjustable and breaking capctity with rotary operating mechanism handle ofL&T/SIEMENS/ Schneider make - 4 nos.

i) Panel should be duly painted with two coats super enameled paint of approved colour, one coat red oxide primer and internally wired with suitable size of copper wire including Protection Relay, ELCB, RCCB, other Protection units, cooling & insulation pads all complete as per site requirement and IE rules. including capacitor banks (APFC) for power factor.

Supplying and fixing following way prewired TP&N MCB distribution board of steel sheet for 415 volts on surface/ recess complete with loose wire box, terminal connectors for all incoming and outgoing circuits, duly prewired with suitable size FR PVC insulated copper conductor up to terminal blocks, tinned copper bus bar, neutral link, earth bar, din bar, detachable gland plate, interconnections, powder painted including earthing etc. as required.(But without MCB/ RCCB/ Isolator) (415 V ,50HZ,100A)

Cost of Earthing with all the materials as per IS-3043 for each motor.

Cost of supplying triple spur gear type chain pulley block of 2 ton lifting capacity with 6 m lift complete with load chain & hand chain suitable for above lift, tested to 50% over loadas per IS 3832 carrying ISI mark.

Cost of 240 Sq mm x 3.5 core 1.1 KV Grade stranded aluminium conductor PVC insulated PVC sheathed armoured cable including laying on wall or on floor as and where required etc. all complete

Cost of construction of 55 sq mm x 3 core unarmoured copper conductor PVC insuated PVC sheathed 1.1 KV grade cable including laying on wall or on the floor as and where required etc. all complete

Supply and installation of servo controlled 250 KVA oil cooled 3-phase Automatic voltage stabiliser with input 220-460V and output 415V +/-1%.with all accessories,etc all complete including earthing , oil,change over switch, etc as per site requirement.

Supplying & Fixing lightning protection at ESR

Supply, delivery and installation of Fire Extinguisher ABC Type 4.5 kg

Supply, delivery and installation of First aid box with gloves, scissors, adhesive plaster, sterilising solution etc.

Raw Water Rising main.

Doing Geotechnical survey, Collecting field data, designing, getting it approved by competent authorityand Laying of Raw water Rising Main (Please refer to Section 5,Sl. 3.0 of SBD).

Supplying centrifugally cast (spun) ductile iron pressure pipe for water supply with socket and spigot ends confirming to IS839/2000 in standard lengths of class K-9 suitable for push on joinr( rubber gasket jointing) with cement mortar lining on inside surface and outside surface zinc coating with bituminous paint including all other taxes insurance carriage to work site with loading unloading etc. stacking includfing inspection charges and all taxes all complete)

DI Pipe 300 mm dia class K-9

Providing and supplying ISI standard D.I. specials and fitting with rubber gasket of S.B.R. complete with cast iron follower gland and M.S. nut & bolts coated from rusting and suitable for D.I. pipes including cost of all labours and materials and transportation to stores/ site, loading, unloading including all taxes, etc. complete as per I.S. 9523

Non return valve (DWSD120A) wthout by pass P.N 1.6 300 mm dia

Providing double flanged sluice valve confirming for IS 2906/14846 including worn gear arrangements as per test pressure stainless steel spindle caps including all transportation etc. complete PN-1:6 without bypass arrangement

Sluice Valve (300 mm dia)

Providing and supplying air valves as per IS-14845-2000 andf MJP's standard specifiations double orifice type combined with screw down isolating valve, small orifice elastic ball resting on a gun metal orifice nipple, large orifice vulcanite ball seating on moulded seat ring, inlet and dreilled including all taxes ( central and local) insurance third party inspection charges, loading, unloading, transportation uotp departmental stores/site etc.complete double ball flanged type PN-1.0 with small orifice 50 mm

Air Valve=50 mm

carriage of K-9 DI pipe 300 mm dia lead 500 KM (payment will be made as per actual lead)

Earthwork in excavtion ( as per IS 3114/1965) for laying of different types and size of pipes so as to give one meter average cover over the socket of pipe with disposal of excavated earth within initial lead and lift as per specification and direction of engineer -in -v\charge ( b0 for classification of soil item-B

Earthwork in excavation of foundation trenches as per design section in ordinary soft rock( wide classification of soil item-c) and disposal of excavated materials so obtained ( 50 M away from the edge of the trenches) with initial lead of 150 M and initial lift of 1.5 m as per specification and direction of E/I in ordinary or soft rock( where blasting is not required)

Supplying labours, tools, tackles, lubricant etc for laying and jointing C.I.S/S tyson pipes ( class LA ) trenches supplying rubber gasket ( rubber gasket confirming to I.S.S.-5382-1969) and making gasket joints including providing night guard barrier and red light to safe guard against accident , all complete ( pipe to be supplied departmentally free of cost and laying of pipes is to be done as per ( I.S.S.-3114-1985) as per design , specification and direction of E/I. With out gas kate.

300 mm dia DI K-9

Providing laying and fixing in proper alingment in position all types of DI air valves as directed by engineer- in - charge including cost of conveyance from store to site of work , cost of all material and giving satisfactory hydraulic testing etc. complete for all class of valve

50 mm dia

Supplying labour and tool for fixing DI sluice valve trenches with a pair of DI tail pair including making flanged joints as per iS specification, including flanged joists as per IS specification confirming to I.S.S. 782-19978 confirming to I.S.S. 6557-1972 and nuts and bolts confirming to I.S.S. 1364-1983. including drilling holes in flanged if required as per specification and direction of E/I. (sluice valve and pieces to be supplied departmentally free of cost).

300mm dia sluice valve + NR Valve

Earthwork in back filling the trenches after laying different types and sizes of pipes with earth removed during excavation within initial lead and lift as per specification and direction of engineer-in charge ( for classification of soil item A& B)

supplying labours, tools and tackles for testing of lead C.I. or D.D. or U.P.V.C. or H.D.P.E. or A.C. Pressure pipe upto 60 mtr head of water all complete as per specification and direction of E/I ( water to be supplied free of cost departmentally)

300 mm dia

Supplying all materials, labours, tools and equipment and constructing brick masonry chamber of (1.20 X 0.9 X 1.50) . inner size having 25cm. thick 75A brick masonry wall in C.M. (1:6), over 150mm. P.C.C. M- 150, laid over one brick flat soling on 100mm. local sand filling, including 12mm. thick cement plaster with punning of inner surface and exposed surface of B/W in C.M. (1:6) and R.C.C. M- 150 cover slab 150mm. thick with 20mm. to 6mm. graded stone chips, and clean coarse sand of F.M. 2.5 to 3 including providing CI surface box and screening shuttering, mixing, placing, striking, curing, taxes and royalty all complete as per approved design, drawing & specification and direction of E/I.

Supply all materials & construction of Thrust Block of RCC M - 200 with nominal mix of (1:1.5:3) in foundation and plinth with approved quality of stone all complete job as per specification and direction of E/I.

Clear Water Rising main.

Doing Geotechnical survey, Collecting field data, designing, getting it approved by competent authorityand Laying of Clear water Rising Main (Please refer to Section 5,Sl. 3.0 of SBD)

Supplying centrifugally cast ( spun) ductile iron pressure pipe for water supply with socket and spigot ends confirming to IS839/2000 in standard lengths of class K-9 suitable for push on joinr( rubber gasket jointing) with cement mortar lining on inside surface and outside surface zinc coating with bituminous paint including all other taxes insurance carriage to work site with loading unloading etc. stacking includfing inspection charges and all taxes all complete)

DI Pipe 200 mm dia class K-9

DI Pipe 300 mm dia class K-9

Providing and supplying ISI standard D.I. specials and fitting with rubber gasket of S.B.R. complete with cast iron follower gland and M.S. nut & bolts coated from rusting and suitable for D.I. pipes including cost of all labours and materials and transportation to stores/ site, loading, unloading including all taxes, etc. complete as per I.S. 9523

Non return valve (DWSD120A) wthout by pass P.N 1.6 200 mm dia

Providing double flanged sluice valve confirming for IS 2906/14846 including worn gear arrangements as per test pressure stainless steel spindle caps including all transportation etc. complete PN-1:6 without bypass arrangement

Sluice Valve (200 mm dia)

Sluice Valve (300 mm dia)

Providing and supplying air valves as per IS-10845 andf MJP's standard specifiations double orifice type combined with screw down isolating valve, small orifice elastic ball resting on a gun metal orifice nipple, large orifice vulcanite ball seating on moulded seat ring, inlet and dreilled including all taxes ( central and local) insurance third party inspection charges, loading, unloading, transportation uotp departmental stores/site etc.complete double ball flanged type PN-1.0 with small orifice 50 mm

Air Valve=50mm

carriage of K-9 DI pipe lead 500 KM (payment will be made as per actual lead)

200 mm dia

300 mm dia

Earthwork in excavtion ( as per IS 3114/1965) for laying of different types and size of pipes so as to give one meter average cover over the socket of pipe with disposal of excavated earth within initial lead and lift as per specification and direction of engineer -in -v\charge ( b0 for classification of soil item-B

Earthwork in excavation of foundation trenches as per design section in ordinary soft rock( wide classification of soil item-c) and disposal of excavated materials so obtained ( 50 M away from the edge of the trenches) with initial lead of 150 M and initial lift of 1.5 m as per specification and direction of E/I in ordinary or soft rock( where blasting is not required)

Supplying labours, tools, tackles, lubricant etc for laying and jointing C.I.S/S tyson pipes ( class LA ) trenches supplying rubber gasket ( rubber gasket confirming to I.S.S.-5382-1969) and making gasket joints including providing night guard barrier and red light to safe guard against accident , all complete ( pipe to be supplied departmentally free of cost and laying of pipes is to be done as per ( I.S.S.-3114-1985) as per design , specification and direction of E/I.

Providing laying and fixing in proper alingment in position all types of DI air valves as directed by engineer- in - charge including cost of conveyance from store to site of work , cost of all material and giving satisfactory hydraulic testing etc. complete for all class of valve

50 mm dia

Supplying labour and tool for fixing DI sluice valve trenches with a pair of DI tail pair including making flanged joints as per iS specification, including flanged joists as per IS specification confirming to I.S.S. 782-19978 confirming to I.S.S. 6557-1972 and nuts and bolts confirming to I.S.S. 1364-1983. including drilling holes in flanged if required as per specification and direction of E/I. ( sluice valve and pieces to be supplied departmentally free of cost).

200mm dia sluice valve + NR valve

300mm dia sluice valve

Earthwork in back filling the trenches after laying different types and sizes of pipes with earth removed during excavation within initial lead and lift as per specification and direction of engineer-in charge ( for classification of soil item A& B)

Supplying labours, tools, tackles, lubricant etc for laying and jointing C.I.S/S tyson pipes ( class LA ) trenches supplying rubber gasket ( rubber gasket confirming to I.S.S.-5382-1969) and making gasket joints including providing night guard barrier and red light to safe guard against accident , all complete ( pipe to be supplied departmentally free of cost and laying of pipes is to be done as per ( I.S.S.-3114-1985) as per design , specification and direction of E/I. With out gas kate.

200 mm dia DI K-9

300 mm dia DI K-9

supplying labours, tools and tackles for testing of lead C.I. or D.D. or U.P.V.C. or H.D.P.E. or A.C. Pressure pipe upto 60 mtr head of water all complete as per specification and direction of E/I ( water to be supplied free of cost departmentally)

200 mm dia

300 mm dia

Supplying all materials, labours, tools and equipment and constructing brick masonry chamber of (1.20 X 0.90 X 1.50). inner size having 25cm. thick 75A brick masonry wall in C.M. (1:6), over 150mm. P.C.C. M- 150, laid over one brick flat soling on 100mm. local sand filling, including 12mm. thick cement plaster with punning of inner surface and exposed surface of B/W in C.M. (1:6) and R.C.C. M- 150 cover slab 150mm. thick with 20mm. to 6mm. graded stone chips, and clean coarse sand of F.M. 2.5 to 3 including providing CI surface box and screening shuttering, mixing, placing, striking, curing, taxes and royalty all complete as per approved design, drawing & specification and direction of E/I.

Supply all materials & construction of Thrust Block of RCC M - 200 with nominal mix of (1:1.5:3) in foundation and plinth with approved quality of stone all complete job as per specification and direction of E/I.

DISTRIBUTION MAIN

Doing Geotechnical survey, Collecting field data, designing, getting it approved by competent authorityand Providing all labour, materials, equipment to procure and laying of DI class K-7 pipes with Cement Mortar Lining for distribution main

Earthwork in excavtion ( as per IS 3114/1965) for laying of different types and size of pipes so as to give one meter average cover over the socket of pipe with disposal of excavated earth within initial lead and lift as per specification and direction of engineer -in -v\charge ( b) for classification of soil item-B

Earthwork in excavation of foundation trenches as per design section in ordinary soft rock( vide classification of soil item-c) and disposal of excavated materials so obtained ( 50 M away from the edge of the trenches) with initial lead of 150 M and initial lift of 1.5 m as per specification and direction of E/I in ordinary or soft rock( where blasting is not required) balance 25 % of total earth work of taken classification soil item-C

Pucca road ( except black top only taken out material to be used) for cutting road as per requirement. Assuming 20 % of total road cutting

Water Bound Macadam Road ( taken out material will be used for cutting road as per requirement

Dismantling plain cement or lime concrete work including stacking serviceable materials in countable stacks within 15 meter lead and disposal of un- seviceable materials with all leads all complete as per direction of E/I.

Providing PCC M-150 in nominal mix of (1:2:4) in foundation with approved quality of stone chips 20mm-6mm size graded and clean coarse sand of FM 2.5 to 3.0 including screening shuttering mixing cement concrete in mixer and placing in position vibrating striking curing taxes and royalty all complete as per building specification and direction E/I(150mm) 5238.46x0.30x0.15

Earthwork in back filling the trenches after laying different types and sizes of pipes with earth removed during excavation within initial lead and lift as per specification and design of engineeer-in-charge ( for classification of soil item B & C)

Supplying centrifugally cast(spun) ductile iron pressure pipe for water supply with socket and spigot ends confirming to IS8329/2000 in standard lengths of class K-7 suitable for push on joint ( rubber gasket jointing) with cement mortar lining on inside surface and outside zinc coating with bituminous paint including all other taxes insurance carriage to work site with loading unloading etc. including inspection charges and all complete ( including carriage up to 450 km)

100 mm dia

150 mm dia

200 mm dia

250 mm dia

300mm dia

carriage of K-7 DI pipe lead 450 KM (payment will be made as per actual lead)

100 mm dia

150 mm dia

200 mm dia

250 mm dia

300mm dia

Providing and supplying ISI standard D.I. specials and fitting with sealing rubber gasket of S.B.r. complete with cast iron follower gland and M.S. nut and bolt coated or otherwise protected from rusting and suitable for D.I. pipes including cost of all labours and materials and transportation to stores/site, loading , unloading including all taxes, etc. complete as per I.S. 9523

Labour charge for one cutting of cast iron pipe and specials including supplying necessary tools and plants ,chipping or filling the surface finish as per specification and direction of E/I

Supplying labours, tools, tackles, lubricant etc for laying and jointing C.I.S/S tyton pipes9 class LA) trenches supplying rubber gasket ( rubber gasket confirming to I.S.S.-5382-1969) and making gasket joints including providing night guard , barriee and red lkight to safe guard against accident all complete ( pipe to be supplied departmentally free of cost and laying of pipes is to be done as per I.S.S. 3114-1985) as per design, specification and direction of E/I.

100 mm dia

150 mm dia

200 mm dia

250 mm dia

300 mm dia

Providing double flanged sluice valve confirming for IS 2906/14846 including worn gear arrangements as per test pressure stainless steel, spindle, caps including all transportation etc. complete without bypass arrangement PN 1

100 mm dia

150 mm dia

200 mm dia

250 mm dia

300 mm dia

Providing double flanged sluice valve/SV conforming for IS-2906/14896 including worn gear arrngement as per test pressure stainless steel,spindle caps including all transportion cmplete

100 mm dia (for scouring)

Providing , installing and giving satisfaction field testing of flanged ends bulk water meter of following type and as mentioned below in (a) and (b) with FGI-250 cast iron body , class "B" confirming to I.S. 2373 or as per ISO 4064, marked to resd in metric system, alongwith manufacturer's test and guarantee certificate including cost of all material with ISI mark or EEC mark enclosed type as per IS 2373

250 mm dia

300 mm dia

Supplying labour and tool for fixing DI sluice valve trenches with a pair of DI tail pair including making flanged joints as per iS specification, including flanged joists as per IS specification confirming to I.S.S. 782-19978 confirming to I.S.S. 6557-1972 and nuts and bolts confirming to I.S.S. 1364-1983. including drilling holes in flanged if required as per specification and direction of E/I. ( sluice valve and pieces to be supplied departmentally free of cost).

Sulice Valve + Scour Valve

100 mm dia

150 mm dia

200 mm dia

250 mm dia

300 mm dia

Supplying labours, tools and tackles for testing of lead C.I. or D.I. or U.P.V.C. or H.D.P.E. or A.C. pressure pipe upto 60 mtr head of water all complete as per specification and direction of E/I( water to be supplied free of cost departmentally).

100 mm dia

150 mm dia

200 mm dia

250 mm dia

300mm dia

Supplying all materials, labours, tools and equipment and constructing brick masonry chamber of (1.20 X 0.90 X 1.50). inner size having 25cm. thick 75A brick masonry wall in C.M. (1:6), over 150mm. P.C.C. M- 150, laid over one brick flat soling on 100mm. local sand filling, including 12mm. thick cement plaster with punning of inner surface and exposed surface of B/W in C.M. (1:6) and R.C.C. M- 150 cover slab 150mm. thick with 20mm. to 6mm. graded stone chips, and clean coarse sand of F.M. 2.5 to 3 including providing CI surface box and screening shuttering, mixing, placing, striking, curing, taxes and royalty all complete as per approved design, drawing & specification and direction of E/I.

Twin Type Staff Quarter - 1 Unit (Please refer to Section 5,Sl. 2.7 of SBD)

E/W in Excavation in foundation trenches in ordinary soil (Vide classification of soil Item -B) & disposal of excavatd earth obtained to a distance up to 50 M including all lift leveling ramming the foundation trenches removing root of trees scrubs all complete as per approved design.

Providing ,coarse clean sand in filling in foudation trenches /in Plinth including ramming & watering in layers not exceeding 150 mm thick with all leads lift including cost of all materilas ,labour , royalty & taxes all complete as per building specification & direction Of E/I

Providing designation 75 A one brick flat soiling joints filled with local sand including cost of watering taxes royalty all complete as per building specification & direction of E/I

Providing P.C.C M-100 in nominal mix of (1:3:6) in foundation with appoved quantity of stone metal (50 mm 25 mm dia size)graded & clean coarse sand of F.M 2.5 to 3 including screening , shuttering , mixing cement concrete in mixer & placing in position , vibrating , striking , curing taxes & royalty all complete as per building specification & direction of E/I

Providing designation 75 A brick work in C.M. (1:6) in foundation 7 Plinth with approved quality of clean coarse sand of F.M 2 to 2.5 including Providing 10 mm thick mortar joints ,Cost of screening , materials , Scaffolding , raking out joints to 15 mm depth curing , taxes & royalty all complete as per building specification & direction of E/I

Providing 25 mm thick damp proof coarse with cement concrete M-150 with nominal mix of (1:2:4) with approved quality of stone chips of 20 mm to 6 mm size graded and clean coarse sand of F.M 2.5 to3 including screening , shuttering mixing cement concrete in mixer with 5% cico or any other approved water proffing compound and placing in position , vibrating , striing , curing , taxes & royalty all complete as per building specification & direction of E/I

Providing designation 75 A brick work in C.M (1:6) in super structure with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing10 mm thick motar joints ,cost of screening , materials, scaffolding,raking out joints to 15 mm depth curing , taxes & royalty all complete as per building specification & direction of E/I

Providing R.C.C M-150 with nominal mix of (1:2:4) in lintel level with approved quality of stone chips 20 mm to 6mm size graded & clean coarse sand of F.M 2.5 to including screening , centring, shuttering and mixing cement concrete in mixer & placing in position vibrating striking curing (but excluding the cost of reinforcement ) taxes & royalty all complete as per building specification of (E/I.

Providing average 63 mm thick R.C.C M -150 with nominal mix (1:2:4) chajja in shelves with approved quality of stone chips 20 mm to 6 mm size graded & clean coarse sand of F.M 2.5 to 3 including making drip course in concrete , screening , centering shuttering & mixing cement concrete in mixer & placing in position vibrating ,striking ,6 mm cement plaster (1:4) in celling & sides of chajja with sand of F.M 1.5, Curing ( But excluding the cost of reinforcement ) taxes and royalty all complete as per building specification of E/I

Providing R.C.C. M-150 nominal mix of (1:2:4) in roof slab with approved quality of stone chips 20mm to 6 mm size graded and clean coarse sand F.M. 2.5 to 3 including making drip course in concrete, screening, concreting, shuttering and mixing cement concrete mixer and placing in position vibrating curing ( but excluding the cost of reinforcement ) taxes and royalty all complete as per building specification of E/I

Supplying fitting & fixing good quality ,well dressed & well seasoned sal wood work in choukhat in doors , windows , skylights , fan light and C/W celestial windows openings , including wedge over all clamps complete including application of two coats of wood preservative of approved quality on the surface butting walls & lintels all complete as per building specification & direction of E/I

Supplying fitting and fixing 250X20X6 mm L-type M.S Clamp properly fish tailed .including making holes and setting the same in 375 X125X75 mm cement concrete block (1:2:4) with cost of all labour and materials and taxes as per building specification and diection of E/I @6 for each door & 4 for each window Total Quantity -(2X3X6+2X4X4)=68 nos

Supplying all materials , labours and fitting & fixing 38 mm (1.5) thick good quality seasoned sal wood battened shutter ledged & braced in door and windows with oxidized iron fitting such as hingles ,sliding door bolts , tower bolts , handles or ings hooks and eye , cleats , sand block as per schedule , taxes & royalty all complete as per building specification & direction of Engineer -in- charge

Supplying , fittings & fixing M.S /Gril made of 20X6 mm M.S flat as per approved design & drawing properly fabricated with joints continous filllet welded and finshed smooth , carriage of grill to work site hoisting as per the building specification and direction of E/I ( where materials is not supplied by the Deptt .)

Providing 25 mm thick pre cast R.C.C M-150 with nominal mix of (1:2:4) in jali with approved quality to stone chips of 6mm nominal size and clean coarse sand of FM 2.5 to 3 with 1.6 mm thick M.S wire as per approved design and drawing and placing the same in position true to plumb and level and properly grouted with cement mortar (1:3) including cost of curing , Scaffolding and finishing all complete as per building specification and direction E/I

Providing and fixing fan hook of 16 mm dia M.S bar 1 meter long bent to reqired size and shape placed in position and fixing in R.C.C slab/beam at the time of casting all complete as per building specification of E/I where material is not supplied by cheet

Supplying , fitting and Fixing M.S Grill gate made of 20X 6 mm M.S or 16 mm M.S raurbar Flat fitted on 25 mm X 25 mm X 6mm M.S angle frame of size 60X60X6 as per approved design including cost of fabrication & drawing , properly fabricated with joints continuous fillet welded & finished smooth, providing necessary locking arrangements with Haskell & dummy duly fixed in C.C (1:2:4) blocks of reuired size applying a priming red lead paints over steel works , taxes , carriage of grill to work site , asper the building specification & direction of E/I ( where materials is not supplied by the Dept)

Providing 6 mm thick cement plaster (1:4) in celling with approved quality of clean coarse sand of F.M 1.5 including screening , curing with all leads & lifts of water , scaffolding , taxes & royalty all complete as per building specification & direction of E/I

Providing 12 mm thick cement plaster (1:6) with approved quality of clean coarse sand of F.M 1.5 including screening .Curing with all leads & lifts of water , Scaffolding , taxes 7 royalty all complete as per building specification & direction of E/I.

Providing cement 1:3 (12mm ) plaster with cement mortar (1:3) using clean coarse sand finishing with neat punning a dado 6" (150 mm) high a side room and out side wall upto plinth level includng screening , curing with all leads & lifts of water , scaffolding , taxes and royalty all complete as per building specification & direction of E/I

Earth work in filling in foudation trenches & Plinth in layers not exceeding 150 mm thick well watered ,rammed ,fully compacted & fine dressed with earth obtained from excavation of foundation trenches within a lead of 50 m & lift of 1.5 m all complete as per building specification & direction of E/I ( Mode of measurement compacted volume)

Providing average 150 mm thick dry rammed khoa bitten to 112mm( compacted with water ) made of well burnt or jhama bricks including ramming properly till compacted thickness is achieved, curing and carriage of water with all leads making proper slope and blending the top with cement mortar (1:10) all complete as per building specification and direction of E/I.

Providing 25 mm thick . First class patent stone flooring (1:2:4) with stone chips in two layers ,bottom layer 19 mm thick (1:2:4) with 12 mm to 6 mm size graded stone chips and top layer 6 mm thick (1:2) with 6 mm down stone chips in pannels including cost of curing , finishing the surface smooth by rubbing with carborandum stone taxes & royalty with all complete as per building specification & direction of E/I

Providing designation 75 A one brick on edge flooring in C.M (1:4) with top surface flush pointed in CM (1:4) approved quality of clean coarse sand of F.M 2 to 2.5 including the cost of screening ,raking out joints to 15 mm depth , curing taxes,royalty all complete as per building specification and direction (E/I)

White washing three coats over new surface with approved quality of lime including the cost of cleaning surface thoroughly and removing the scales & mosh marks with jhama rubbing, scaffolding washing of floors and taxes all complete as per building specification and direction of E/I.

Color washing two coats over a coat of white wash over new surface with approved quality of lime in approved shade including the cost of cleaning surface thoroughly and removing the scales & mosh marks with jhama rubbing, scaffolding washing of floors and taxes all complete as per building specification and direction of E/I.

Providing two coats of synthetic enamel paint of approved shade and make over new wooden surface including cleaning the surface after removing dirt, scales, smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specification & direction of E/I

Providing primer one coat of red lead paint of approved make over new steel surface including preparing the surface after cleaning , removing rust ,dirt ,scales ,smokes and grease and cleaning the surface thouroughly including cost of scaffolding and taxes all complete as per building specification and direction of E/I

Providing two coats of painting with ready mixed paint of approved shade & make over steel surface including cleaning the surface thoroughly, scaffolding & taxes all complete as per building specification & direction of E/I.

Providing tor steel reinforcement of 8 mm dia as per approved design and drawing excluding carriage of bars to work site ,cutting, bending and binding with annealed wire with cost of wire removal of rust placing the rods in position all complete as per Specification and direction of E/I.TMT Fe 500 (Only valid for SAIL and TATA )

Carriage of materials from divisional store or kiln site or quarry site to work site including contract profit, loading, unloading, transportation, etc. all complete .

Cement 30 KM lead

Steel 30 KM lead

Sand 30 KM lead

Bricks 30 KM lead

Stone/Stone Chips 30 KM lead

Water Supply Sanitation Installation (Plumbing work)

Supplying and laying GI pipes of approved make in trenches with red lead and yarn with socket and screw joints and cutting pipes in size and threading ends where necessary including carriage of materials up to work site etc. all complete as per specification and direction of E/I.

i) 25mm GI. Pipe.

ii) 15 mm GI. Pipe.

Supplying materials and labours for fixing GI Pipes with red lead paints and yarn with screwed and sockted joints on wall, celling and floor including supplying of wall hooks of pipe clamp, wooden plugs, cutting pipe to size and threading ends where necessary all complete as per specification and direction of E/I.

i) 15 mm GI. Pipe

Supplying, fitting and fixing of GM ferrule of approved make in DI/CI main including drilling and tapping CI/DI main etc. all complete as per specification and direction of E/I.

Supplying and fixing GI fittings of approved make all complete as per direction of E/I.

(a) Elbow 15 mm dia

(b) Tee plane 15mm dia

(c) Nipple 15mm dia.

(d) Union Socket 25mm dia

(e) Union Socket 15mm dia

(f) Brass bib cock 15mm dia

(g) C.I stop cock 15mm dia

(h) C.I. stop cock 25mm dia

(i) Reducing Socket 25x15mm

(j) Tee 25x25x15mm dia

Supplying, fitting and fixing vitreous white glazed earthen were I W C of parry Hindustan or any other I.S.S approved make with 100 mm HCI ‘P’ trap, 15 Liters CI pull and let go flushing cistern of names or other ISS equivalent make complete with all fittings C.I. or C.C brackets, 32 mm, alkathene /PVC telescopic flush pipe about 2 mtrs. long with one brass coupling and clamps, GI chain and pull including supplying and fixing a pair of vitreous white glazed earthen were footrest to be fixed in floor, 15 mm .CI body brass spindle, stop cock of weight not less than 50 grams, 15 mm. PVC connection pipe 450 mm. long and the exposed pipe and cistern with two coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/I. (510mm.long with 12.5 Liter low level PVCSystem).

SEPTIC TANK and SOAK PIT

Earth work in excavation in foundation trenches in ordinary soil (vide classification of soil item-B) and disposal of excavated earth as obtained to a distance up to 50 m including all lifts, leveling, ramming the foundation trenches, removing roots of trees, shrubs all complete as per approved design, building specification and direction of E/I.

Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials, labours, royalty and taxes all complete as per building specification and direction of E/I.

Providing designation 75A one Brick flat soling, joints filled with local sand including cost of watering, tax, royalty all complete as per building specification and direction of E/I.

Providing P.C.C M150 with nominal mix of (1:2:4) in foundation with approved stone chips 20mm to 6mm size well graded and clean course sand of FM-2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, Vibrating, striking, curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing water proof cement plaster (1:3) with clean course sand of F.M- 1.5mm with 5% cico or any other approved water proofing compound including taxes and royalty all complete as per building specification and directions of E/I.

(a) 19 mm thick

(b) 12 mm thick

Providing designation 75A bricks work in C.M. in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm. thick mortar joints, cost of screening materials racking out joints to 15 mm. depth, curing taxes and royalty all complete as per building specification and direction of E/I.

(a) B/W in C.M (1:4)

(b) B/W 75-B in (1:6) for Soak pit

(c) Brick work in dry masonry for soak pit.

Providing pre cast R.C.C. M-150 with nominal mix of (1:2:4) slab of desired size with approved quality of stone chips and clean coarse sand of FM 2.5 to 3 including curing, shuttering, carrying the slab manually to site and laying in position all complete (but excluding the cost of reinforcement), taxes and royalty etc. all complete as per building specification and direction of E/I.

Providing for reinforcement as per approved design and drawing excluding carriage of tor rod to work site including cutting bending and binding with annealed wire with cost of wire removal of rust placing the rods in position all complete as per Specification and direction of E/I.

10 mm dia

Supplying fitting and fixing H.C.I. Pipe/ H.C.I. fitting of Approved make confirming to I.S.S 1729 including supplying nails and bobbins lead and yarn from making lead caulked joints including earth work or providing scaffolding as the case may be all complete as per specification and direction of E/I.

(a) 100mm dia H.C.I. Tee.

(b) 100mm dia H.C.I. Band

(c) 50mm dia H.C.I. Cowel

(d) 50mm dia H.C.I. Vent pipe

(e) 100mm H.C.I. Pipe

Supplying materials and labours and fixing 20mm dia M.S bar steps in wall of 0.3 m interval and staggered in (1:2:4) cement concrete including scaffolding and curing etc. all complete as per specification and direction of E/I.

Supplying all materials, labours, tools and tackles and 100mm dia R.C.C hume pipe and laying jointing, testing, earth work including carriage of materials etc. all complete.

Supplying 50mm size brick bats and filling in soak pit including carriage and labours etc. all complete as per direction of E/I.

Supplying materials and labours for constructing inspection chamber of designation class 75 B bricks size 750mm deep, 600x450mm internal dimension having 250mm wall thickness in cement mortar (1:6) including 12mm cement plaster (1:4) with punning on inside and cement plaster (1:6) with 600x475 mm G.I. Cover With frame ( Weight not less than 36 Kg.) along with earth work in excavation and 80mm thick P.C.C. (1:3:6) in foundation and refilling all complete as per specification and direction of E/I

Electrical Works

Point wiring in PVC conduit with modular type switch wiring for light point /fan point with 1.5 sqmm F.R. PVC insulated copper conductor single core cable in surface/recessed PVC conduit with modular switch modular plate, suitable G.I. box and the point with sqmm FR PVC insulated copper conductor single core cable etc as required

Wiring for twin control light point with 1.5 sqmm F.R. PVC insulated copper conductor single core cable in surface/recessed PVC conduit with two way modular switch modular plate, suitable G.I. box and the point with sqmm FR PVC insulated copper conductor single core cable etc as required

Wiring for light /power plug point with 2 x 4 sqmm F.R. PVC insulated copper conductor single core cable in surface/recessed PVC conduit along with one no 4 sqmm FR PVC insulated copper conductor single core cable for loop earthing etc as required

Copper sub main wiring in PVC conduit Wiring for sub main wiring with PVC insulated copper conductor single core in surface/recessed PVC conduit as required

2 x 1.5 sqmm + 1 x 1.5 sqmm earth wiring

2 x 2.5 sqmm + 1 x 2.5 sqmm earth wiring

Supplying and fixing following way three pole and neutral sheet MCB distribution board 415 volts on surface/recessed complete with tinned copper bush bars ,neutral link, earth bar, din bar, detachable gland plate inter connection phosphatised and power painted including earthing etc as required (but with out mcb / rccb / Isolator) (4 +12 ) double door horizontal type

Supplying and fixing 6 amp to 32 amp, rating 240 volts, B series miniature circuit breaker of single poles in existing MCB DB complete with connecting ,testing, and commissioning etc as required

Earthing with G.I. earth pipe 4.5 M long 40mm dia including accessories and providing masonry enclosure with copper plate having locking arrangement and watering pipe etc with charcoal ,salt all complete as per electrical rule

Supplying ,fitting and fixing following sizes of PVC conduct along with accessories in surface / races including cutting the wall and making good the same in case of recessed conduit as required

PVC con 20 mm PVC pipe

PVC con 25 mm PVC pipe

Installation commissioning and testing Ceiling Fan

Carriage of ceiling fan and regulator

Supplying ,fitting and fixing 5 amp ceiling rose on the existing junction

Supplying ,fitting and fixing breas batten/ angle holder including connection etc.

Supplying ,fitting and fixing G.I. box with modular plate and cover in front of surface or in recess including providing and fixing 3 pin 5/6 amp modular type switch, connection, painting etc as required.

Supplying ,fitting and fixing G.I. box with modular plate and cover in front of surface or in recess including providing and fixing 6 pin 5/6 amp and 15/16 amp socket outlet and 15/16 amp modular type switch, connection, painting etc as required.

Supplying and drawing co-axial T.V. cable RG-06 grade 0.7 nn solid copper conductor PE insulated seilded with fine tinned cover braid and protected with PVC sheath in the existing surface / recessed steel/ PVC conduit as required.

Supplying and fixing modular switch / socket on the existing modular plate and switch box including connection but excluding modular plate etc,as required. TV antenna socket out put

Supplying ,fitting and fixing modular base and cover plate on existing modular metal boxes etc as required.

Cost of Earthing with G.I. earth pipe 4.5 M long 40mm dia G.I.Pipe 600mm x 600mm x 6mm thick copper earth plate, and 8 SWG copper wire including cost of making 1.2x1.2x3m deep pit and filling with charcoal ,salt all complete as per electrical rule

Compound Wall/ Boundry Wall (432.80 M Long)

Doing Geotechnical survey, Collecting field data, designing, getting it approved by competent authority Construction of Compound wall. etc. all complete job.

Earthwork in excavation in foundation isolated footing trenches in hard soil (Class A) and disposal of excavated earth as obtained to a distance of 50m. including all lift, levelling, ramming the foundation trenches. Removing roots of trees, shrubs all complete as per specification of E/I.

Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials, labour, royalty and taxes all complete as per building specification and direction of E/I.

Providing designation 75A one brick on edge soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/I.

Providing P.C.C. M150 in nominal mix of (1:2:4) in foundation with approed quality of stone metal grade-III (50mm to 25mm size) clean coarse sand F.M. 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing, taxes and royalty all complee as per building specification and direction of E/I.

Providing R.C.C M - 200 with nominal mix of (1:1.5:3) in foundation with approved quality of stone chips (20mm to 6mm size) clean course sand of F.M 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing RCC M-200 with nominal mix of (1:1.5:3) in stiffeners with approved quality of stone chips 20mm to 6mm size graded and clean coarse sand of F.M 2.5 to 3 including curing, shuttering carrying the slab manually to site and laying in position all complete (but excluding the cost of reinforcement) taxes and royalty, all complete as per building specification and direction of E/I.

Providing RCC M-200 with nominal mix of (1:1.5:3) in band at plinth level with approved quality of stone chips 20mm to 6mm size graded and clean coarse sand of F.M 2.5 to 3 including curing, shuttering carrying the slab manually to site and laying in position all complete (but excluding the cost of reinforcement) taxes and royalty, all complete as per building specification and direction of E/I. Top of Wall

Providing RCC M-200 with nominal mix of (1:1.5:3) in band at lintel level with approved quality of stone chips 20mm to 6mm size graded and clean coarse sand of F.M 2.5 to 3 including curing, shuttering carrying the slab manually to site and laying in position all complete (but excluding the cost of reinforcement) taxes and royalty, all complete as per building specification and direction of E/I. Top of Wall

Providing Tor steel reinforcement of 10 mm ,12 mm , &16 mm dia Bars as per approved design and drawing excluding carriage of M.S bars to work site , cutting ,bending and binding with annealed wire with cost of wire ,removal of rust , Placing the rods in position all complete as per building specification and direction of E/I.

Providing designation 75A brick work in CM(1:6) in superstructure with approved quality of clean coarse sand of FM 2 to 2.5 including providing 10mm thick mortar joints, cost of screening, scaffolding, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing 12mm cement plaster (1:6) with clean coarse sand of F.M. 1.5 including cost of screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I

Providing two coats of snowcem of approved shade and make over a coat of cement primer on new surface inculding preparing the plastered surface smooth with sand paper,scaffolding,curing and taxes all complete as per building specification & direction of E\I.

Supplying fitting & Fixing M.S. grill gate with M.S. grills made 20x6mm M.S. flat or 16mm M.S. square bars fitted 25x25x6 mm M.S. angle frame of size 60x60x6 mm including cost of fabrication, providing necessary locking arrangement with haskal and domny duly fixed in P.C.C (1:2:4) blocks of required size, applying a priming red lead paint over steel work , taxes all complete as per drawing specification and direction of E/I.

Filling in foundation trenches and plinth in layers not exceeding dressed with earth obtained from excavation of foundation trenches with a lead of 50 M and lift of 1.5 M all complete as per building specification and direction of E/I

Providing two coat of painting with ready mixed paint of approved shade and make over steel surface

Carriage of material from divisional store are kiln side or quality side to work including contractor profit loading ,unloading transportation are complete .

Cement 30 KM lead

Sand 30 KM lead

Bricks 30 KM lead

Stone/Stone Chips 30 KM lead

Approach Road

Construction of embankment with approved meterial obtained from borrow pits with all lift and leads, transporting to site sperading,grading to required slope and compacting to meet requirment of to tables 300.2 rolling with smooth wheeled roller

Granular sub base with Corse Graded Material (Table:-400-2) for grading one materials Construction of granual sub base by providing coarse graded marterial, spreading in unifrom layer with mortar grade on prepared surface , mixing by mix in place method with rotavator at OMC , and compecting with vibratory roller to achiver the desired dencity ,complete as per clouse 401,

construction of un-reinforced dowel jointed plain cement concrete pavement over a prepared sub base with 43 grade cement @400kg per cum, coarse and fine aggregate confirming to IS 383, maximum size of coarse and fine aggregate not exceeding to 25mm mixed in a batching and mixing plant as per approved mix desigen ,transported to site , laid with a fixed from or slip from paver , spread ,compacted and finished in a continuousoperation including provision of contraction , expansion,sealant primer, joint sealant,debonding strip, dowel bar,tie rod, admixtures as approved , curing compound, finishing to lines and grades as per drawing

Granular sub base with corse graded material (table:-400-2) (construction of granular sub-base by providing coarse graded material,spreading in unifrom layers with motor grader on prepared surface ,mixing by mix in place method with rotavator at OMC,and compacting with vibratory roller to achieve the desired density ,complete as per clause 401) for grading I material

Carriage of material from divisional store are kiln side or quality side to work including contractor profit loading ,unloading transportation are complete .

Cement 30 KM lead

Sand 30 KM lead

Stone/Stone Chips 30 KM lead

Boulder 10 KM lead

House Connection for 6410nos Consumer.

Earth work in excavation in foundation trenches in hard soil vide classification item-B and disposal of excavated earth as obtained to a distance upto 50 m including all lifts,levelling,ramming the foundation trenches,removing roots of trees,shrubs all complete as per approved design,building specifications and direction of E/I.

Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials labours , royalty and taxes all complete as per building specification and direction of E/I.(mode of measurement compacted volume)

Providing P C C M-150 in nominal mix of (1:2:4)in foundation with approved quality of stone chips 20mm to 6mm size graded and clean coarse sand of F.M2.5 to 3 including screening shuttering , mixing cement concrete in mixer and placing in position ,vibratig, striking, curing, taxes and royalty all complete as per building specification and direction of E/I.

Earth work in back fillingthe trenches after laying of different types and sizes of pipes with earth removed during excavation within initial lead and lift as per specification and direction of E/I.(For soil item A & B)

Providing 12 mm thick cement plaster (1:3) with clean coarse sand of F.M 1.5 with 1.5 mm thick cement punning over it including screening, curing, with all leads and lifts of water,taxes and royalty all complete as per building specification an direction of E/I.

Providing and supplying Blue MDPE pipes confirming to ISO 4427:1996 manufactured from virgin resin PE 80 food grade compounded raw materials having blue colour only assurance certificate from quality agencies like WRC/CIPET (India) / DVGM / KIWA/SPGN etc for usage in drinking water with quality system. The cost shall include testing of all materials all taxes central, state, Municipal, Inspection charges transportation up to site ,transit insurance, loading, unloading, stacking etc complete as specified and directed.PN16(SDR-9) with ED-20 mm

Supplying labours and tools for fixing G.I.Pipes with red lead and yarn of following nominal bore with screwed and socketed joints on wall ,ceiling and floor including supplying and fittings of wall hooks or pipe clamps ,wooden plugs, cutting pipes to size and threading ends if required etc all complete as per specification and direction of E/I.-15 mm

Lowering laying and jointing HDPE/MDPE pipes in proper position including all specials by compression fitting / electrofusion and But fusion jointing procedure including hydroulic testing as per relevent IS code complete with all materials for jointing procedures like Electrofusion machine , electric mirror/heater/ But fusion welding machine with hydroulic jack,top loading clamp etc pump and accessories for hyroulic tesing and all labours as directed by E/I.as per IS-7634 part-2-20 mm

Supplying labours and tools for fixing G.I.Pipes with red lead and yarn of following nominal bore with screwed and socketed joints on wall ,ceiling and floor including supplying and fittings of wall hooks or pipe clamps ,wooden plugs, cutting pipes to size and threading ends if required etc all complete as per specification and direction of E/I.-15 mm

Supplying and fixing G.M. ferrule of approved make in existing C.I./D.I. main including drilling and taping C.I./D.I. main all complete as per specification and direction of E/I. 3 mm, 6 mm 10 mm dia ferrule weight not less than 425 gram

Providing and fixing of G.M. Fullway valve of approved quality all complete as per specification and direction of E/I. 20 dia and weight not less than 400 Gm

Providing and fixing of male ended C.I.Body brass spindle valve and seat Bib cock of approved quality with extra socket all complete as per specification and direction of E/I. -15 dia and weight not less than 400 Gm

Supplying and fixing G.I.fitting of approved make all complete as per specification and direction of E/I.

20 mm dia ELBOW

15 mm dia ELBOW

20mm dia Reducing socket

20mm dia Nipple

15mm dia Nipple

20mm dia Union Socket

15 mm dia Socket

20mm dia socket

Carriage of material from divisional store are kiln side or quality side to work including contractor profit loading ,unloading transportation are complete .

Cement 30 KM lead

Sand 30 KM lead

Stone/Stone Chips 30 KM lead

Operation & Maintenance for two years

O/M work with Labour component & Materials for 1st Year

As per SBD Section - 5 Clouse 9.10

O/M work with Labour component & Materials for 2nd Year

As per SBD Section - 5 Clouse 9.10

O/M work with Labour component & Materials for 3Rd Year

As per SBD Section - 5 Clouse 9.11

O/M work with Labour component & Materials for 4TH Year

As per SBD Section - 5 Clouse 9.12

O/M work with Labour component & Materials for 5TH Year

As per SBD Section - 5 Clouse 9.10

Add 12% GST

Add 1% Labour Cess

UMSL Limited

M/S BINOD KUMAR LAL

M/S AMRESH KUMAR GUPTA