Development of playfield at Mela Hiranagar Kathua by way of construction of volleyball court, cricket pitch, open air gym and allied works

Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as10 sqm on plan including disposal of excavated earth, lead up to 50 meter and lift upto 1.5m, as directed by Engineer-in-Charge.All kinds of soil :

Treatment of soil using chemical like round up for anti weeding laid in holes @ 300 mm c/c and consumpution @ 600 ml/ 10 Sqm

Consolidation of subgrade with power road roller of 8 to 12 tonne capacity including making good the undulations etc. with earth or quarry spoils etc. and rerolling the subgrade

Excavating, supplying and filling of local earth (RBM)(including royalty)by mechanical transport upto a lead of 15 km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete.

P/L and compacting stone agrregates of different sizes to form contour and elevation to the desired level as per the Drawing and instruction of Engineer Iincharge (size 40 mm /20 mm/10mm ) down black stone aggregate up to a depth of 300 mm from below primary backing . Layers of stone to be rolled as per desired slope and compaction using 8-10 tonnes Road roller over open area & pitch roller over areas with drainage pipes.

Supply and installation of artificial UV resistanat polyethylene synthetic grass with rigid monofilment yarn, minimum 40mm pile height. The turf should have minimum 40mm Pile Height made of POLYETHYLENE Monofilament & Pile weight minimum 900 g/m2 and above and stitched rate minimum @ 120/ mtr or above. The turf should have Dtex/Denier >=12300. The Primary backing of turf should be made of 100% POLYPROPYLENE, minimum weight 240 gram/m2 and above with Coating with Carboxylated SBR Latex appr. 1200 gr/m2 or Butadiene Styrene with weight of 900 g/sqm and total backing wt should not be less than 1140 g/sqm or as approved by FIFA under FIFA Quality Category. The infill must be 22-25Kg Silica Sand, minimum 7kg & above SBR Rubber Granules. The line marking shall be stitched tufted material (Painted lines are not acceptable). The rate is inclusive of All applicable taxes, Lavies, Octoria, transportation loading/unloading complete except custom duty exumption Including Maintenance of 3 years by way of brushing and adding infill as and when required.

Providing of Fixing Height Adjustable Fixed Volley Poles 4 INCH with Net and Anteena

Earth work in excavation by manual means in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed: All kinds of soil :

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering . All works upto plinth level 1:4:8 mix (1 cement: 4 coarse sand:8 graded stone aggregates) 40 mm nominal size (crushed)

Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level with 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level Thermo-Mechanically Treated bars of grade Fe-500D or more

Centring and shuttering including strutting, propping etc. and removal of form work for Lintel, beams, plinth beams, girders, bressumers and cantilevers

Steel work welded in built up section framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer.

Providing and fixing G.I Chain link Fabric fencing of required width in mesh size 50x50mm including strengthening with 2mm dia wire or nuts, bolts and washers as required complete as per direction of Engineer in Charge Made of G.I wire dia 4mm

Finishing wall with premium acrylic smooth exterior paint with silicone additives of required shade on New work (two or more coats applied @ 1.43 liter/10sqm over and including priming coat of water exterior paint applied @ 2.20kg/10sqm)

Applying priming coat: With ready mixed red oxide Zinc Chromate primer of approved brand and manufacture on steel galvanized iron/steel works

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade. Two or more coat on new work

Supply and laying of PVC insulated and PVC sheathed / xlpe aluminium power cable of 1.1 KV grade of following sizes on surface / direct in ground including sand cushioning protective covering and refilling the trench as required as per direction of Engineer Incharge 16 sq. mm 2 core

Supply and laying of PVC insulated unsheathed bright annealed bare copper industrial cable for voltage grade upto 1100V as per IS694:1990 3 core 4 sq. mm

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 20 mm

Supplying and fixing Cable End Box (Loose Wire Box) suitable for following single pole and neutral, sheet steel, MCB distribution board, 240 Volts, on surface/ recess, complete with testing and commissioning etc. as required.For 6 way, Double door SPN MCBDB

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole and neutral 32 Amp

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole and neutral 63 Amp

Installation, Testing and commissioning IP 67 Flood lights 200 watt minimum Luminous flux of luminaire 120 Lm/w, Colour temperature of 5700K, Neutral white, CRI > 80, 50,000 operating hours with PCLens and necessary wire for connection and other accessories required for fixing lights on existing Poles. Firm has to submit originallity certificate of material from OEM or Authorized Distributor with 05 years of warranty.

Providing and fixing of 1 Hp pump with motor with necessary fitting & wire and connections complete as per direction of engineer incharge Havells or equivalent make

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. (external work) Medium 15 mm dia. nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. (external work) Medium 20 mm dia. nominal bore

Providing and fixing ACP main board 3mm thickness on 1 x 1 inch tubular frame with writing of Name of stadium etc as per direction of engineer incharge

Provision for supply and Installation of Pedestal for Inaguration made of MS Frame 40 x 40 x 2.6 mm with 4 mm thick ACP Sheet as base of size 4' x 6' and Acrylic Inaguration Plate Acrylic sheet cover as per direction of Engineer Incharge

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering . All works upto plinth level 1:1.5:3 mix (1 cement: 1.5 coarse sand: 3 graded stone aggregates) 20 mm nominal size (crushed)

Centering and shuttering including strutting, propping etc. and removal of form work for: Foundations, footings, bases for columns

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting , hoisting , fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. 10.16.1 Hot finished welded type tubes

Providing and fixing precoated galvanized iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Finishing walls with Acrylic smooth exterior paint of required shade: Old work (two or more coats applied @ 1.67 liters/10sqm on existing cement paint surface)

Manufacturing supplying and fixing retro reflective overhead signage boards made up of 2mm thick aluminum sheet, face to be fully covered with high intensity and encapsulated lens type heat activated retro reflective sheeting conforming to type-III of ASTM-D-4956-01 as approved by Engineer-in-charge; letters, borders etc. as per IRC : 67-2001 in silver white with blue colour background and with high intensity grade, pasted on substrate by pressure sensitive adhesive backing which shall be activated by applying pressure conforming to class -II of ASTM-D-4956-01 and fixing the same to the plate of structural frame work by means of suitable sized aluminum alloys, rivets or bolts and nuts @ 300mm c/c all along the periphery as well as in two vertical rows along with theft resistant measures including the cost of painting with two or more coats of epoxy paint in grey colour on the back side of aluminum sheet including appropriate priming coat. The rate includes the cost of rounding off the corners, lowering down the structural frame work from the gantry, fixing and erecting the same in position all complete as per drawing, specification and direction of Engineer-in-charge (Structural frame work including M.S. plate to be provided separately. Rectangular area of the sheet only shall be measured for payment). Overhead informatory road signage.

40mm thick marble chips flooring rubbed, under layer 28mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5mm nominal size) and top layer 12mm thick with white, black, chocolate, grey, yellow or green marble chips of sizes from 7 mm to 10mm nominal size, laid in cement marble powder mix 3:1 (3 cement : 1 marble powder) by weight in proportion of 2:3 (2 cement marble powder mix :3 marble chips) by volume including cement slurry and curing complete : Ordinary cement without any pigment.

Centering and shuttering including strutting, propping etc. and removal of form work for: Edges of slabs and breaks in floors and walls under 20 cm wide

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Providing and fixing of heavy duty net of thickness 2.5mm (mesh size 48x48 mm) to cover cricket prctice pitch on 3 sides & Top, as per direction of engineer in charge

Arm wheel: Providing and fixing Arm wheel in a pair with below specifications: Dimensions(LxWxH): 850 x 800 x 1800 mm Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. Wheel frame of NB 32mm with connecting spokes of NB 25mm, Pipe connecting main p

ilar with wheel frame of NB 50mm. All pipes must be (G.I.) ‘C’ Class Pipes. (‘NB’ stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimeters). All Pipes shall be powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. All joints of pipe shall be robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint shall be applied at all the welding points prior to finishing. Base plate of12 mm thickness have cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated shall be used in the equipment manufactured. The equipment shall be shall be fixed on ground with J shaped welded bolts of 18mm thickness. Once the concrete is set, the equipment is fixed on to it and nuts and bolts shall be covered with base plate cover. High tensile steel with galvanized nut bolts shall be used for assembly. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment. Rates Inclusive of all Carriage, Taxes, Fixing & Maintenance of same upto 3 years as and when required.

ELLIPTICAL EXERCISER Providing and fixing of Elliptical exerciser with below specifications: Dimensions (LxWxH): 1200 x 550 x 1600 mm Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. Main frame of NB 80mm (G.I.) ‘C’ Class Pipe. Handle frame of NB 32mm and NB 25mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimeters). All Pipes shall be powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. All joints of pipe shall be robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint shall be applied at all the welding points prior to finishing. Handle bars shall be provided with high end quality rubber grips. Base plate of12 mm thickness have cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated shall be used in the equipment manufactured. The equipment shall be fixed on ground with J shaped welded bolts of 18mm thickness. Once the concrete is set, the equipment is fixed on to it and nuts and bolts shall be covered with base plate cover. High tensile steel with galvanized nut bolts shall be used for assembly. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment. Foothold made of Co-Polymer Plastic with rounded edges to prevent impact and injury. Rates Inclusive of all Carriage, Taxes, Fixing & Maintenance of same upto 3 years as and when required.

DOUBLE CROSS WALKER Providing and fixing of Double cross walker with below specifications: Dimensions (LxWxH): 1600 x 600 x 1600 mm Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. Handle main frame of NB 50mm and other connecting pipes of NB 32mm and NB 25mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimeters). Foot support frame of 96 x 46 x 3mm MS rectangular pipe. All Pipes shall be powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. All joints of pipe shall be robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint shall be applied at all the welding points prior to finishing. Base plate cover made of virgin LLDPE plastic by rotational molding with minimum 4.00mm thickness, UV resistant and colored. Foothold made of Co-Polymer Plastic with rounded edges to prevent impact and injury. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated shall be used in the equipment manufactured. The equipment shall be fitted with inbuilt limiters to prevent unwanted movements. The equipment shall be fixed on ground with J shaped welded bolts of 18mm thickness. Once the concrete

is set, the equipment is fixed on to it and nuts and bolts shall be covered with base plate cover. High tensile steel with galvanized nut bolts shall be used for assembly. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment. Self-Explanatory stainless-steel label shall be fixed on equipment for ease of use. Rates Inclusive of all Carriage, Taxes, Fixing & Maintenance of same upto 3 years as and when required.

TRIPLE TWISTER Providing and fixing of Triple twister with below dimensions: Dimensions (LxWxH): 1300 x 1300 x 1650 mm Shall be Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. Handle Main frame of NB 32mm (G.I.) ‘C’ Class Pipe. Handle frame spokes of NB 25mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimeters). Foothold plate of made of MS Sheet Metal of 3mm thickness. All Pipes shall be powder coated with 80–120-micron thick AkzoNobel or equivalent Paints. All joints of pipe shall be robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint shall be applied at all the welding points prior to finishing. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated shall be used in the equipment manufactured. The equipment shall be fixed on ground with concrete of minimum strength M- 25 and J shaped welded bolts of 18mm thickness & Base plate of 12 mm thickness. Once the concrete is set, the equipment shall be fixed on to it. High tensile steel with galvanized nut bolts shall be used for assembly. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment. Rates Inclusive of all Carriage, Taxes, Fixing & Maintenance of same upto 3 years as and when required.

DOUBLE PULL CHAIR Providing and fixing of Pull chair in a pair with below specifications: Dimensions (LxWxH): 2400 x 800 x 2000 mm Shall be Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. Seat main frame of NB 50mm (G.I.) ‘C’ Class Pipe, Pipe connecting main post with handle frame of NB 65mm (G.I.) ‘C’ Class Pipe. Handle frame of NB 32mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore i.e., Internal Diameter of pipe in millimeters) All Pipes shall be powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. All joints of pipe shall be robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all the welding points prior to finishing. Handle bars to be provided with high end quality rubber grips. Base plate of12 mm thickness have cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored. Seat to be made up from virgin LLDPE manufactured by rotational molding with 4.00 mm thickness, colored, UV resistant and environmental friendly. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated to be used used in the equipment manufactured. The equipment shall be fitted with inbuilt limiters to prevent unwanted movements. The equipment shall be fixed on ground with concrete of minimum strength M- 25 and J shaped welded bolts of 18mm thickness. Once the concrete is set, the equipment is to be fixed on to it and nuts and bolts to be covered with base plate cover. High tensile steel with galvanized nut bolts shall be used for assembly. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment. Self-Explanatory stainless steel label to be fixed on equipment for ease of use. Rates Inclusive of all Carriage, Taxes, Fixing & Maintenance of same upto 3 years as and when required.

SIT UP STATION Providing and fixing of Double sit-up station with below specifications: Dimensions (LxWxH): 1600 x 1150 x 650mm shall be Fabricated with main frame of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. Main frame of NB 25mm (G.I.) ‘C’ Class Pipe. Leg support of NB 65mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nomina

l Bore i.e., Internal Diameter of pipe in millimeters) Perforated MS Sheet for Back Support. The back support Fixed on its top is to be made of perforated MS sheet of 2mm thickness. All pipes shall be powder coated using Akzo Nobel or equivalent Paint of 80- 120 micron thick. All joints of pipes shall be robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint is to be applied at all welding points prior to finishing. Base plate of12 mm thickness have cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored. The equipment is to be fixed on ground with J shaped welded bolts of 18mm thickness. Once the concrete is set, the equipment is to be fixed on to it. High tensile steel with galvanized nut bolts shall be used for assembly. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment. Rates Inclusive of all Carriage, Taxes, Fixing & Maintenance of same upto 3 years as and when required.

AIR SWING Air swing in a pair with below specifications: Dimensions (LxWxH): 1150 x 900 x 1250 mm To be Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. Leg Support frame of NB 50mm (G.I.) ‘C’ Class Pipe. Handle support frame of NB 32mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore i.e., Internal Diameter of pipe in millimeters) All Pipes shall be powder coated with 80–120-micron thick AkzoNobel or equivalent Paints.All joints of pipe shall be robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint shall be applied at all the welding points prior to finishing. Handle bars shall be provided with high end quality rubber grips. Base plate of12 mm thickness have cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored. Foothold made of MS Sheet Metal with rounded edges to prevent impact and injury. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated shall be used in the equipment manufactured. The equipment shall be to be fitted with inbuilt limiters to prevent unwanted movements. The equipment is to be fixed on ground with J shaped welded bolts of 18mm thickness. Once the concrete is set, the equipment is to be fixed on to it and nuts and bolts shall be covered with base plate cover. High tensile steel with galvanized nut bolts shall be used for assembly. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment. Self-Explanatory stainless steel label fixed on equipment for ease of use Rates Inclusive of all Carriage, Taxes, Fixing & Maintenance of same upto 3 years as and when required.

LEG PRESS Providing and fixing leg press in a pair with below specifications: Dimensions (LxWxH): 2000 x 600 x 1800 mm Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. Seat Main frame of NB 50mm (G.I.) ‘C’ Class Pipe and Pipe connecting main post to seat main frame of NB 65mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore i.e., Internal Diameter of pipe in millimeters) All Pipes shall be powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. All joints of pipe shall be robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint is applied at all the welding points prior to finishing. Base plate of12 mm thickness have cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored. Foothold made of NB 50mm (G.I.) ‘C’ Class Pipe. Seats made up from virgin LLDPE manufactured by rotational molding with 4.00 mm thickness, colored, UV resistant and environmental friendly. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated shall be used in the equipment manufactured. The equipment shall be fitted with inbuilt limiters to prevent unwanted movements. The equipment is fixed on ground with concrete of minimum strength M- 25 and J shaped

welded bolts of 18mm thickness. Once the concrete is set, the equipment is fixed on to it and nuts and bolts shall be covered with base plate cover. High tensile steel with galvanized nut bolts shall be used for assembly. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment. Rates Inclusive of all Carriage, Taxes, Fixing & Maintenance of same upto 3 years as and when required.

Knee Hip Raise (Chin Ups / Dips / Push Ups): CHIN UPS: Instrumental in building upper body muscles especially that of the back and shoulder. Wide and narrow grips provide for various permulations of popular exercise. DIPS: Soft handgrips for dipping using your own body weight. A very strong and robust exercise fortriceps, shoulders and back muscles. PUSH UPS: Appropriately heighted rolled bars that relieve unneces-sary stress from wrist and forearms. Allows user to dip lower for a more complete arm, chest, shoulder and back workout. Dimensions (LxWxH): 1400 x 1100 x 2100mm. Fabricated with base frame of NB 50mm (G.I.) ‘C’ Class Pipe of approved make. Main frame of NB 50mm (G.I.) ‘C’ Class Pipe. Leg support of NB 32mm (G.I.) ‘C’ Class Pipe and other support of NB 25mm (G.I.) 'C' Class Pipes (‘NB’ stands for Nominal Bore i.e., Internal Diameter of pipe in millimeters), All pipes shall be powder coated using Akzo Nobel or equivalent Paint of 80-120 micron thick. All joints of pipe shall be robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs, Zinc primer paint is applied at all welding points prior to finishing,The equipment is fixed on ground with J shaped welded bolts of 18mm thickness,Once the concrete is set, the equipment is fixed on to it.High tensile steel with galvanized nut bolts shall be used for assembly, Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment. Base plate of12 mm thickness have cover made of virgin LLDPE plastic by rotational moulding with 4.00mm thickness, UV resistant and coloured. Rates Inclusive of all Carriage, Taxes, Fixing & Maintenance of same upto 3 years as and when required.

Horse rider station Horse rider station with below specifications: Dimensions (LxWxH): 1000 x 600 x 1100 mm Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make Main frame of NB 65mm (G.I.) ‘C’ Class Pipe. Handle support frame of NB 50mm (G.I.) ‘C’ Class Pipe and other pipes of NB 32mm & NB 25mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore i.e., Internal Diameter of pipe in millimeters) All Pipes shall be powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. All joints of pipe shall be robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint is applied at all the welding points prior to finishing. Base plate of12 mm thickness have cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored. Foothold made of NB 32mm (G.I.) ‘C’ Class Pipe. Seat to be made up from virgin LLDPE manufactured by rotational molding with 4.00 mm thickness, colored, UV resistant and environmental friendly. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated shall be used in the equipment manufactured. The equipment shall be fitted with inbuilt limiters to prevent unwanted movements. The equipment is fixed on ground with concrete of minimum strength M- 25 and J shaped welded bolts of 18mm thickness. Once the concrete is set, the equipment is fixed on to it and nuts and bolts shall be covered with base plate cover. High tensile steel with galvanized nut bolts shall be used for assembly. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment. Self-Explanatory stainless steel label fixed on equipment for ease of use. Rates Inclusive of all Carriage, Taxes, Fixing & Maintenance of same upto 3 years as and when required.

Exercising bar Exercising bar in a pair with below specifications: Dimensions (LxWxH): 1800 x 550 x 150

0 mm Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. Main frame of NB 32mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimeters). All Pipes shall be powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. All joints of pipe shall be robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint is applied at all the welding points prior to finishing.Make approved by authority and maintenance of same upto 3 years cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored. The equipment is fixed on ground with J shaped welded bolts of 18mm thickness. Once the concrete is set, the equipment is fixed on to it and nuts and bolts shall be covered with base plate cover. High tensile steel with galvanized nut bolts shall be used for assembly. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment. Rates Inclusive of all Carriage, Taxes, Fixing & Maintenance of same upto 3 years as and when required.

Rowing machine Rowing machine with below specifications: Dimensions (LxWxH): 1250 x 800 x 1150 mm Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. Main frame of NB 65mm (G.I.) ‘C’ Class Pipe. Handle support frame of NB 25mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimeters). All Pipes shall be powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. All joints of pipe shall be robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint is applied at all the welding points prior to finishing. Base plate of12 mm thickness have cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored. Foothold made of NB 50mm (G.I.) ‘C’ Class Pipe. Seat to be made up from virgin LLDPE manufactured by rotational molding with 4.00 mm thickness, colored, UV resistant and environmental friendly. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated shall be used in the equipment manufactured. The equipment shall be fitted with inbuilt limiters to prevent unwanted movements. The equipment is fixed on ground with J shaped welded bolts of 18mm thickness. Once the concrete is set, the equipment is fixed on to it and nuts and bolts shall be covered with base plate cover. High tensile steel with galvanized nut bolts shall be used for assembly. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment. Rates Inclusive of all Carriage, Taxes, Fixing & Maintenance of same upto 3 years as and when required.

Providing and fixing of Durable SBR TILE flooring Protects floor from damages by dumbbells and iron gym material Thickness:25 mm Dimensions: 490mm x 490mm SBR-25 SBR TILE of approved make and colour and as per directions of engineer in charge incl cost and carriage incl necessary jointing by cement concrete or adhesives including forming of at least 0.15m x 0.15m or above (width x thickness) block on all sides of tiles as per dierctions of engr incharge including all finishing in all the respects complete job . Rates Inclusive of all Carriage, Taxes, Fixing & Maintenance of same upto 3 years as and when required.

Designing, Supply, installation and third party testing and commissioning of Solar Standalone street light system with MPPT charge controller and IP 65 protection and Luminous Flux of 4500 lm & lumen efficacy of 150 lumen/watt or more, lithium ferro phosphate battery pack, MONO Crystalline type Solar board with 60W or more PV Module & Solar board voltage of 18 V having movement and Lux Sensor, with 2000 cycle Battery charging & discharging cycles with Color rendering index (CRI) >70 & Dimmable Configurability. Note: Firm has to submit originallity certificate of material from OEM or Authorized Distributor with 05 years of warranty.

Earth work in excavation by mechanical means (hydraulic excavator) in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed, within a lead of 50 metres:

Centering and shuttering including strutting, propping etc. Suspended floors, roofs, landings, balconies and access platforms.