CERTAIN REPAIR TO HARD STANDING, PATH, PAVEMENT AT OTM ACCN UNDER AGE B/R-II AT ITARANA ALWAR

Demolition of brick work built in cement mortar or cement lime mortar including all quoin arches complete all as specified and directed.

M&L for modular size brick work with fly ash 'brick' straight or curved on plan exc 6m mean radius built cement mortar 1:6 complete all as specified and as directed

Demolition of cement concrete (unreinforced) ground floor and paving n exc 15cm thick below or above ground level complete all as specified and directed.

M&L 75 mm thick PCC 1:4:8 type D2 using 40 mm graded stone aggregate as in sub base complete all as specified and directed.

M&L for 75 mm thick cement concrete (1:3:6) type C1 using 20 mm graded stone aggregate as in plinth protection/Path/hardstanding finish surface even and smooth using extra cement bays not exceeding 2m in length. Joints of 6mm wide and 10mm deep shall be provided along the wall and bays and same shall be filled with bitumen mastic (1:3) complete all as specified and directed by Engineer-in-Charge.

Dismantling of Stone slabs and tiles laid dry/ bedded and pointed in mortar of any description or thickness in floors, aprons, complete all as specified and directed.

M&L for Vibrator moulded (coloured) precast concrete interlocking paver block with grey cement and pigment (Lacquer/ Glossy finish) any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 grade laid over and including 25mm thick sand cushion and filled the joints with dry sand after laying the paver block complete all as specified and directed.

M&L for Vibrator moulded (Coloured) precast concrete interlocking paver block with grey cement and pigment any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 grade laid over 25mm thick sand cushion and filled the joints with dry sand after laying the paver block complete all as specified and directed.

All as per srl item No 8.00 but except tiles

M&L for vibrator moulded precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80mm thickness, M-40 grade and fixed with grey cement and pigment laid over and including 25 mm thick sand cushion and filled the joints with dry sand after laying the paver block complete all as specified and directed.

M&L for 12mm thick vitrified exterior grade textured finished tiles (ENDURA JOHNSON OR EQUIVALENT HEAVY DUTY TILES FOR PARKING/PORCH) of size exc 0.09 sqm each but n. exc 0.16 sqm set and jointed in net cement slurry in floor including cement mortar (1:4) screed bed 20mm thick and pointing with admixture of white/colour cement and pigment complete all as specified and directed

M&L chequered cement concrete (coloured) tiles 30cmx30cmx25mm thick with (Lacquer/glossy finish) set and jointed in net cement slurry in floor and pointed with coloured cement and pigment including cement mortar ( 1:4) screed bed 20mm thick complete all as specified and directed

M&L Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete complete all as specified and directed

M&L for PCC 1:2:4 type B1 (using 20mm graded crushed stone aggregate) as in floor laid in alternate panels, finishing the cement concrete surface even and smooth without using extra cement complete all as specified and directed

Forming construction joints 30mm deep and 10mm wide finished with sealing compound Grade 'A' complete all as specified and directed.

M&L providing cement concrete (1:2:4) type B1, using 20mm graded crushed stone aggregate as in roof kerbs or mud stops, rounded or chamfered on edges in lintels upto 1.5m clear span,cills, steps, seismic and other similar bands, plinth courses, string courses , lacing courses, parapets and railings upto 60cm in height, copings kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering slightly rounded or chamfered angles and throating complete all as specified and directed.

M&L in replacement of precast cement concrete louvers and jallies, 35 mm thick (measured solid), including all moldings but excluding frame type B0 (1:2:4) (12.5 mm size graded stone aggregate) set in CM (1:4) complete all as specified and directed

Demolition of reinforced cement concrete of any description and in any position (reinforcement cut as required to facilitate demolition) all as specified & as directed.

Providing precast cement concrete type B-1 (1:2:4) (20mm Graged aggregates) in window or door cills, lintels, bressumers, steps, quoin blocks (for use with masonry), string courses, copings. kneelers, apex stones, pier caps, columns, posts, boundary pillars, bed plates, pintle blocks, anchorage blocks, bonders (for stone walling). corbels, brackets, etc. (of any section indicated), with plain fair faces, including chamfers, weatherings, throat- ing etc. and setting in mortar complete with joints to match complete all as specified and directed.

S&F 110mm dia PVC (SWR) pipes single sockets, in any length with rubber ring joints, laid in trenches or floors complete all as specified and directed.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed.

M&L for rendering 10 mm thick in CM 1:4 on fair faces of brick work or concrete surfaces rendering is to be finished even and smooth without using extra lime or cement complete all as specified and directed.

M&L for rendering 15 mm thick in CM 1:4 on stone masonry surfaces or surface other than fair face of brick-work rendering is to be finished even and smooth without using extra lime or cement complete all as specified and directed.

M&L for Rough cast plaster on exterior walls applying the under coat of cement and sand mortar 1:3 not less than 10mm thick and while it is still in plastic state the roughcast mixture consisting of crushed stone or fine gravel aggregate (size between 6 to 12mm) mixed with coarse sand and cement in the raio of 1:1:1 shall be applied and finished even. The mix of cement and sand shall made slightly wetter than normal for rendering to ensure that larger aggregate are thoroughly covered complete all as specified and directed by Engineer in Charge.

M&L for preparation of newly plastered wall surfaces and applying two coats of cement based paint over a coat of primer complete all as specified and directed.

M&L preparation of old decorated plastered surfaces of walls and applying one coat of cement base paint of approved shade/tint complete all as specified & as directed.

M&L for preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide all as specified and directed.

M&L for preparation of newly concrete surface as kerb stone surface and applying two coat of synthetic enamel paint over a coat of primer as approved complete all as specified and directed

M&L for preparation of old concrete / plastered surface as kerb stone surface and applying two coat of synthetic enamel paint as approved complete all as specified and directed

S&F for 75mm thick steel fibre reinforced (SFRC) man hole cover with iron frames (medium) complying to the standard specifications as mentioned in the IS 12592 BIS Standard, minimum load bearing capacity 5 ton/sqm, in square, rectangular or circular shape complete all as specified & as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed

Dismantling AC/CGI/Fibre sheet (Corrugated, Semi corrugated etc) as in roof etc complete all as specified and directed

Steel work as in Steel work in tubular trusses including special shaped washer etc. omplete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 complete all as specified and directed

S&F for preparation of new steel surface of any description over 10cm width or girth & applying two coats of synthetic enamel paint over a coat of primer complete all as specified and directed.

S&F for pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering /cladding to wall fixed with self tapping screws complete all as specified and directed.

M&L for cutting channels, grooves or rebates n exc 15cm girth, and making good in cement mortar 1:4 to match existing surfaces complete all as specified and directed.

M&L for Cutting holes in brick /stone walls not exc half brick depth in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required complete all as specified and directed.

Excavating in post holes in soft loose soil (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm complete all as specified and directed.

M&L repair to pot holes any depth, area not exceeding 1.0 Sqm each and including sweeping free from dust and mud or water scoring sunken surfaces in road path etc cutting around edges, at least 25mm in depth and making good by filling the potholes with Premix bituminous instant road repair material such as patchmate etc and including well ramming surface to get true surface complete all as specified and directed.