mplementation of Jal Jeevan Mission to provide Functional Household Tap connection to Rural Households in Package no.08-JJM-II/2020-21 at Village Panchayats in Kariapatti Panchayat Union of Virudhunagar District in Phase-II for the year 2020-21

Amount

Providing Borewell, Pumpset, Pumping Main, FHTC at Namachivayapuram Village of Panthanenthal Panchayat In Kariapatti Block

Borewell

Charges for conducting Geophysical survey for identifying the favourable drilling point

Drilling of 6'' Dia bore well in soft rock area including trench protection charges etc., complete.Clay Soil

Drilling of 6'' Dia bore well in hard rock area including trench protection charges etc., complete.Hard Soil

Supply & delivery of 150mm Dia PVC Plain Casing pipe as per IS 12818 / 2010

Pumpset

Supply and delivery of clear water vertical wet type submersible pumpset suitable for 150mm dia borewell conforming to IS 8034/2002 as amended thereafter and BEE 3 Star Rated capable of discharging noted LPM against head of water column due to all causes. The pump shall be with stainless steel shaft and dynamically balanced bronze or Cast SS impeller, brass screws and CI FG 200 grade pump bowl/diffuser with ISI mark. The pump shall be directly coupled to a continuos rated two pole suitable wet type vertical squirrel cage induction motor as per IS9283 /1995 as amended there after, suitable for operation in AC three phase 415 V+/- 10 %, 50 HZ +/- 5 %

Supply and delivery of direct online starter confirming to IS13947 and IEC60947-1 suitable KW rating for operation in AC/Three Phase/50HZ(± 5%) and 415 V(±10%) including Ammeter, Voltmeter, Thermal Overload relay, 16 Amps 2 pole Magnetic Contactor with under Voltage protection, Indication lamp, starting capacitor, running capacitor and On/Off Push button switches, 5 way connector, wiring with 1 sq. mm/1.5 sq. mm copper PVC insulated cable, powder coated vermin proof box including the capacitor (the cost of capacitor is to be taken separately).

Supply, delivery of 1.1 KV Grade,PVC insulated and sheathed 3 core flat copper submersible cable with ISI marking conforming of IS 694/1990 of reputed make for submersible motor erected in borewell. 4 sqmm submergible cable

Supply and delivery of GI medium class pipes and specials as per relevant IS as listed below.

50mm GI Pipe

50mm GI Coupling Heavy

50mm GI Elbow Heavy

50mm GI Union Heavy

50mm GI Flange set Heavy

50mm MS Clampset Heavy

50mm GM Non Return Valve

50mm GM Gate Valve

75mm x 50mm PVC Threaded Coupler

Lighting the pumpromm including internal wiring with switch circute fuses etc. with the following light fittings with ISI marking.

40W box type tube light - 1 No.

100W bulb with angle holder

100W bulk head fittings

5 AMPS 3 pin socket with switch

5 Amps switches for light(Flush type)

Providing lighting wiring using MS conduit pipes and specials with 2 runs 1.5 sqmm PVC copper wire and 1 run 12 swg GI wire for earthing for light, fans and 5A plug points etc.,

Obtaining power supply including cost of following materials and by engaging B licence holder.EB fee for application form and deposit amount will be borne by the Board

Aerial fuse board of size 15 x 10 x 6cm with 32 A aerial fuse carrier(3 Nos.)

Wall mounting type MS cubical EB meter box with fuse carrier (3 Nos) of 32 A capacity at EB supply point.This box is also to accommodate TNEB energy meter with proper ventilation as approved by TNEB.

Supply and laying of 7/20 size PVC insulator copper conductor cable from Aerial fuse to EB supply point etc., complete as per I.E Rules.

25mm dia GI pipe for service point

25mm dia GI Elbow

No.8 GI wire for earth(Twin earthing)

Stay wire 7/20

20mm GI pipe for twin earthing and cable encasing

4way nutral link

TW banel board (41 x 31 x 6cm)

Labour charges for erection of submersible pump set including fixing and jointing the submersible cable with clamps to the required depth, valves and errection panel board control room twin earthing as per I.E Rules including cost of civil works

Upto 5 HP

Main line

Earthwork excavation in all type of Soil strata for laying of pipes with the standard trench width and depth as per standard specification

Supply of unplasticised PVC rigid pipes and specials as per IS 4985 / 2000 Specification

75mm OD pvc pipes - 4KSC

75 mm pvc bend

75 mm pvc Tee

75 mm x 50 mm PVC Threaded Coupler

Single Air valve

Supply of unplasticised GI pipes and specials as per as per IS 1239/PART II Specification FOR CULVERT/ ROAD crossing portion

65 mm GI Pipe

65 mm GI bend

65 mm GI coupling

65 mm GI Elbow

Conveying the PVC pipes and specials to trench, Lowering PVC rigid pipes and specials to trench and laying to proper grade and alignment, jointing with PVC couplers with cement paste including testing. .

65 mm GI pipe

75mm OD pvc pipes - 4KSC

Refilling with excavated soil complying with standard specification in layers of 15cm thick well rammed and consolidated after the pipes and specials are laid and tested

Testing of pipes20%

HSC Connection in DI Mains for Water Supply Scheme - Providing suitable dia non corrosive engineering plastic moulded Clamp Saddle with SS 304 threaded metal inserted for tapping outlet suiting for ½”, 3/4” &1” clear bore and with wide plastic strap (Engineering Plastic) with SS 304 suitable bolts & nuts. Saddle to have sealing of Thermo plastic elastomeric (TPE) material around. (20mm)

Common Items for HSC Connection - Brass Ferrule as per IS 319 grade of sizes 15mm, 20mm and 25mm size and threaded as per IS:1554 BSPT, ISO:7-1 to suit the corresponding bore sizes of 15mm, 20mm and 25mm dia size ( 1/2", 3/4" and 1") in the saddle Connection as per IS :1554 BSPT, ISO:7-1 (15mm)

Poly Propylene compression Female Threaded Adaptor with metal insert of SS 304 as per standards ISO 14236 and Tested as per BS 6920 in WRC-NSF LTD, UK for connecting 15mm, 20mm and 25mm outlet points of Brass ferrule of sizes 15mm, 20mm and 25mm respectively. (20mm)

Poly propylene 90 Degree Compression elbow with compression joint at both ends as per standards ISO 14236 and Tested as per BS 6920 in WRC-NSF LTD, UK suitable for 20mm, 25mm and 32mm OD MDPE pipes (20mm)

Poly Propylene compression Female Threaded Elbow with metal insert of SS 304 as per standards ISO 14236 and Tested as per BS 6920 in WRC-NSF LTD, UK suitable for 20mm, 25mm and 32mm OD MDPE pipes (20mm)

Poly Propylene compression Male Threaded Adaptor with metal insert of SS 304 as per standards ISO 14236 and Tested as per BS 6920 in WRC-NSF LTD, UK suitable for 20mm, 25mm and 32mm OD MDPE pipes (20mm)

MDPE PE 80 PN16 Blue pipe as per standards ISO 4427 and Tested as per BS 6920 in WRC-NSF LTD, UK (20mm)

Earthwork Excavation for 20mm PVC pipe laying work including cost of Refilling work as per Standard Specifications 20B (in Rm)

Labour Charges for Laying & Jointing 20 mm pipe in Excavated Trench in Proper Camber

Supply & Laying & Jointing 20 mm PVC Elbow (Mould) BIS 7834/1975 Part V for Tap Connection

Supply & Laying & Jointing 20 mm brass tap

U PVC ball valve with one side compression end and other side female end as per ISO 4422-4 and Tested as per BS 6920 in WRC-NSF LTD, UK,size : 20mm ODx1/2"ID, 25mm ODX1/2"ID and 32mm OD X 3/4" ID - 20mm

50mm GI Saddle piece

Labour charges for Drilling,Cutting and fixing ferrules in distribution line

Supply and delivery of the MS clamp and fixing in wall in open space with required screw etc

cutting MDPE Pipes and specials true axis and finishing the end complete

Providing Borewell, Pumpset, Pumping Main,Pump room, FHTC at Panthanenthal Village Panchayat In Kariapatti Block

Borewell

Charges for conducting Geophysical survey for identifying the favourable drilling point

Drilling of 6'' Dia bore well in soft rock area including trench protection charges etc., complete.Clay Soil

Drilling of 6'' Dia bore well in hard rock area including trench protection charges etc., complete.Hard Soil

Supply & delivery of 150mm Dia PVC Plain Casing pipe as per IS 12818 / 2010

Pumpset

Supply and delivery of clear water vertical wet type submersible pumpset suitable for 150mm dia borewell conforming to IS 8034/2002 as amended thereafter and BEE 3 Star Rated capable of discharging noted LPM against head of water column due to all causes. The pump shall be with stainless steel shaft and dynamically balanced bronze or Cast SS impeller, brass screws and CI FG 200 grade pump bowl/diffuser with ISI mark. The pump shall be directly coupled to a continuos rated two pole suitable wet type vertical squirrel cage induction motor as per IS9283 /1995 as amended there after, suitable for operation in AC three phase 415 V+/- 10 %, 50 HZ +/- 5 %

Supply and delivery of direct online starter confirming to IS13947 and IEC60947-1 suitable KW rating for operation in AC/Three Phase/50HZ(± 5%) and 415 V(±10%) including Ammeter, Voltmeter, Thermal Overload relay, 16 Amps 2 pole Magnetic Contactor with under Voltage protection, Indication lamp, starting capacitor, running capacitor and On/Off Push button switches, 5 way connector, wiring with 1 sq. mm/1.5 sq. mm copper PVC insulated cable, powder coated vermin proof box including the capacitor (the cost of capacitor is to be taken separately).

Supply, delivery of 1.1 KV Grade,PVC insulated and sheathed 3 core flat copper submersible cable with ISI marking conforming of IS 694/1990 of reputed make for submersible motor erected in borewell. 4 sqmm submergible cable

Supply and delivery of GI medium class pipes and specials as per relevant IS as listed below.

50mm GI Pipe

50mm GI Coupling Heavy

50mm GI Elbow Heavy

50mm GI Union Heavy

50mm GI Flange set Heavy

50mm MS Clampset Heavy

50mm GM Non Return Valve

50mm GM Gate Valve

75mm x 50mm PVC Threaded Coupler

Lighting the pumpromm including internal wiring with switch circute fuses etc. with the following light fittings with ISI marking.

40W box type tube light - 1 No.

100W bulb with angle holder

100W bulk head fittings

5 AMPS 3 pin socket with switch

5 Amps switches for light(Flush type)

Providing lighting wiring using MS conduit pipes and specials with 2 runs 1.5 sqmm PVC copper wire and 1 run 12 swg GI wire for earthing for light, fans and 5A plug points etc.,

Obtaining power supply including cost of following materials and by engaging B licence holder.EB fee for application form and deposit amount will be borne by the Board

Aerial fuse board of size 15 x 10 x 6cm with 32 A aerial fuse carrier(3 Nos.)

Wall mounting type MS cubical EB meter box with fuse carrier (3 Nos) of 32 A capacity at EB supply point.This box is also to accommodate TNEB energy meter with proper ventilation as approved by TNEB.

Supply and laying of 7/20 size PVC insulator copper conductor cable from Aerial fuse to EB supply point etc., complete as per I.E Rules.

25mm dia GI pipe for service point

25mm dia GI Elbow

No.8 GI wire for earth(Twin earthing)

Stay wire 7/20

20mm GI pipe for twin earthing and cable encasing

4way nutral link

TW banel board (41 x 31 x 6cm)

Labour charges for erection of submersible pump set including fixing and jointing the submersible cable with clamps to the required depth, valves and errection panel board control room twin earthing as per I.E Rules including cost of civil works

Upto 5 HP

Main line

Earthwork excavation in all type of Soil strata for laying of pipes with the standard trench width and depth as per standard specification

Supply of unplasticised PVC rigid pipes and specials as per IS 4985 / 2000 Specification

75mm OD pvc pipes - 4KSC

75 mm pvc bend

75 mm pvc Tee

75 mm x 50 mm PVC Threaded Coupler

Single Air valve

Supply of unplasticised GI pipes and specials as per as per IS 1239/PART II Specification FOR CULVERT/ ROAD crossing portion

65 mm GI Pipe

65 mm GI bend

65 mm GI coupling

65 mm GI Elbow

Conveying the PVC pipes and specials to trench, Lowering PVC rigid pipes and specials to trench and laying to proper grade and alignment, jointing with PVC couplers with cement paste including testing. .

65 mm GI pipe

75mm OD pvc pipes - 4KSC

Refilling with excavated soil complying with standard specification in layers of 15cm thick well rammed and consolidated after the pipes and specials are laid and tested

Testing of pipes20%

Pump room

Earthwork excavation and depositing on bank with initial lift of 2.00m in hard stiff clay, Stiff Black cotton soil, hard red earth, shales, Murram etc., as per SS 20 B

Collection and supply of sand and filling in to the basement including cost and conveyance to the siteand all labour charges for filling as per standard specifications

Cement concrete 1:4:8 mix using 40mm ISS metal including cost and conveyance of all materials to site and all labour charges for mixing,laying and curing etc complete

Reinforced Cement concrete 1:11/22:3 mix using 20mm ISS metal including cost and conveyance of all materials to site and all labour charges for mixing,laying and curing etc complete

Brick work in CM 1:5 mix using country bricks ground moulded of size 83/4"x41/4"x21/4" for the following including curing etc., complete complying with standard specifications. Rate for 10m3

Supplying and fabrication of steel including cost and conveyance of bending to shape and tying in position and forming grills for all R.C.C works including cost and conveyance of all materials to site and all labour charges for mixing, laying, and curing etc complete

Supplying and erecting centering shuttering including necessary supports for plane surfaces including cost and conveyance of all materials to site and all labour charges etc complete

Lintel,Roof

Sunshade

Floor finish with granolithic flooring in CC 1:2:4 mix using 10 to 12mm chips including cost and conveyance of all materials and labours etc., complete

Finishing the top of roof with one course of PRESSED TILES of size 20 cm X 20 cm X 2 cm laid in cement mortar 1:3 (One cement and three sand) 12mm thick mixed with water proofing compound conforming to I.S. at 2% by weight of cement including cost and conveyance of all materials to site and all labour charges for mixing , laying ,and finishing etc complete

Plastering with cement mortar 1:5 mix to 12mm thick including cost and conveyance of all materials to site and all labour charges etc

Plastering with cement mortar 1:3 mix to 10 mm thick including cost and conveyance of all materials to site and all labour charges etc

White distember two coats using shell lime including cost and conveyance of all materials to site and all labour charges etc comoplete for 100 Sqm

Emulsion two coats using approved colour pigments including cost and conveyance of all materials to site and all labour charges etc complete

Supplying of steel doors, windows, ventilators etc., with best approved best quality etc., complete complying with standard specifications and as directed by the departmental officers.

Doors D1 (1.00x2.00)m

Rcc Jolly 0.60 x 0.45 m

Painting two coats over new iron works using ready mixed enamel paint including cost and conveyance of paint and all labour charges etc complete

Labour charges for fixing of Steel Door including all labour charges etc. complete.

HSC Connection in DI Mains for Water Supply Scheme - Providing suitable dia non corrosive engineering plastic moulded Clamp Saddle with SS 304 threaded metal inserted for tapping outlet suiting for ½”, 3/4” &1” clear bore and with wide plastic strap (Engineering Plastic) with SS 304 suitable bolts & nuts. Saddle to have sealing of Thermo plastic elastomeric (TPE) material around. (20mm)

Common Items for HSC Connection - Brass Ferrule as per IS 319 grade of sizes 15mm, 20mm and 25mm size and threaded as per IS:1554 BSPT, ISO:7-1 to suit the corresponding bore sizes of 15mm, 20mm and 25mm dia size ( 1/2", 3/4" and 1") in the saddle Connection as per IS :1554 BSPT, ISO:7-1 (15mm)

Poly Propylene compression Female Threaded Adaptor with metal insert of SS 304 as per standards ISO 14236 and Tested as per BS 6920 in WRC-NSF LTD, UK for connecting 15mm, 20mm and 25mm outlet points of Brass ferrule of sizes 15mm, 20mm and 25mm respectively. (20mm)

Poly propylene 90 Degree Compression elbow with compression joint at both ends as per standards ISO 14236 and Tested as per BS 6920 in WRC-NSF LTD, UK suitable for 20mm, 25mm and 32mm OD MDPE pipes (20mm)

Poly Propylene compression Female Threaded Elbow with metal insert of SS 304 as per standards ISO 14236 and Tested as per BS 6920 in WRC-NSF LTD, UK suitable for 20mm, 25mm and 32mm OD MDPE pipes (20mm)

Poly Propylene compression Male Threaded Adaptor with metal insert of SS 304 as per standards ISO 14236 and Tested as per BS 6920 in WRC-NSF LTD, UK suitable for 20mm, 25mm and 32mm OD MDPE pipes (20mm)

MDPE PE 80 PN16 Blue pipe as per standards ISO 4427 and Tested as per BS 6920 in WRC-NSF LTD, UK (20mm)

Earthwork Excavation for 20mm PVC pipe laying work including cost of Refilling work as per Standard Specifications 20B (in Rm)

Labour Charges for Laying & Jointing 20 mm pipe in Excavated Trench in Proper Camber

Supply & Laying & Jointing 20 mm PVC Elbow (Mould) BIS 7834/1975 Part V for Tap Connection

Supply & Laying & Jointing 20 mm brass tap

U PVC ball valve with one side compression end and other side female end as per ISO 4422-4 and Tested as per BS 6920 in WRC-NSF LTD, UK,size : 20mm ODx1/2"ID, 25mm ODX1/2"ID and 32mm OD X 3/4" ID - 20mm

50mm GI Saddle piece

Cutting of old CC road for laying the 20mm pvc pipe

Labour charges for Drilling,Cutting and fixing ferrules in distribution line

Supply and delivery of the MS clamp and fixing in wall in open space with required screw etc

cutting MDPE Pipes and specials true axis and finishing the end complete

Providing Borewell, Pumpset, Pumping Main,30,000 ltr OHT, Distribution Line & FHTC in New MBC Colony in Valukalotti Village & panchayat In Kariapatti Block

Borewell

Charges for conducting Geophysical survey for identifying the favourable drilling point

Drilling of 6'' Dia bore well in soft rock area including trench protection charges etc., complete.Clay Soil

Drilling of 6'' Dia bore well in hard rock area including trench protection charges etc., complete.Hard Soil

Supply & delivery of 150mm Dia PVC Plain Casing pipe as per IS 12818 / 2010

Pumpset

Supply and delivery of clear water vertical wet type submersible pumpset suitable for 150mm dia borewell conforming to IS 8034/2002 as amended thereafter and BEE 3 Star Rated capable of discharging noted LPM against head of water column due to all causes. The pump shall be with stainless steel shaft and dynamically balanced bronze or Cast SS impeller, brass screws and CI FG 200 grade pump bowl/diffuser with ISI mark. The pump shall be directly coupled to a continuos rated two pole suitable wet type vertical squirrel cage induction motor as per IS9283 /1995 as amended there after, suitable for operation in AC three phase 415 V+/- 10 %, 50 HZ +/- 5 %

Supply and delivery of direct online starter confirming to IS13947 and IEC60947-1 suitable KW rating for operation in AC/Three Phase/50HZ(± 5%) and 415 V(±10%) including Ammeter, Voltmeter, Thermal Overload relay, 16 Amps 2 pole Magnetic Contactor with under Voltage protection, Indication lamp, starting capacitor, running capacitor and On/Off Push button switches, 5 way connector, wiring with 1 sq. mm/1.5 sq. mm copper PVC insulated cable, powder coated vermin proof box including the capacitor (the cost of capacitor is to be taken separately).

Supply, delivery of 1.1 KV Grade,PVC insulated and sheathed 3 core flat copper submersible cable with ISI marking conforming of IS 694/1990 of reputed make for submersible motor erected in borewell. 4 sqmm submergible cable

Supply and delivery of GI medium class pipes and specials as per relevant IS as listed below.

50mm GI Pipe

50mm GI Coupling Heavy

50mm GI Elbow Heavy

50mm GI Union Heavy

50mm GI Flange set Heavy

50mm MS Clampset Heavy

50mm GM Non Return Valve

50mm GM Gate Valve

75mm x 50mm PVC Threaded Coupler

Lighting the pumpromm including internal wiring with switch circute fuses etc. with the following light fittings with ISI marking.

40W box type tube light - 1 No.

100W bulb with angle holder

100W bulk head fittings

5 AMPS 3 pin socket with switch

5 Amps switches for light(Flush type)

Providing lighting wiring using MS conduit pipes and specials with 2 runs 1.5 sqmm PVC copper wire and 1 run 12 swg GI wire for earthing for light, fans and 5A plug points etc.,

Obtaining power supply including cost of following materials and by engaging B licence holder.EB fee for application form and deposit amount will be borne by the Board

Aerial fuse board of size 15 x 10 x 6cm with 32 A aerial fuse carrier(3 Nos.)

Wall mounting type MS cubical EB meter box with fuse carrier (3 Nos) of 32 A capacity at EB supply point.This box is also to accommodate TNEB energy meter with proper ventilation as approved by TNEB.

Supply and laying of 7/20 size PVC insulator copper conductor cable from Aerial fuse to EB supply point etc., complete as per I.E Rules.

25mm dia GI pipe for service point

25mm dia GI Elbow

No.8 GI wire for earth(Twin earthing)

Stay wire 7/20

20mm GI pipe for twin earthing and cable encasing

4way nutral link

TW banel board (41 x 31 x 6cm)

Labour charges for erection of submersible pump set including fixing and jointing the submersible cable with clamps to the required depth, valves and errection panel board control room twin earthing as per I.E Rules including cost of civil works

Upto 5 HP

Main line

Earthwork excavation in all type of Soil strata for laying of pipes with the standard trench width and depth as per standard specification

Supply of unplasticised PVC rigid pipes and specials as per IS 4985 / 2000 Specification

75mm OD pvc pipes - 4KSC

75 mm pvc bend

75 mm pvc Tee

75 mm x 50 mm PVC Threaded Coupler

Single Air valve

Supply of unplasticised GI pipes and specials as per as per IS 1239/PART II Specification FOR CULVERT/ ROAD crossing portion

65 mm GI Pipe

65 mm GI bend

65 mm GI coupling

65 mm GI Elbow

Conveying the PVC pipes and specials to trench, Lowering PVC rigid pipes and specials to trench and laying to proper grade and alignment, jointing with PVC couplers with cement paste including testing. .

65 mm GI pipe

75mm OD pvc pipes - 4KSC

Refilling with excavated soil complying with standard specification in layers of 15cm thick well rammed and consolidated after the pipes and specials are laid and tested

Testing of pipes20%

Distribution line

Earthwork excavation in all type of Soil strata for laying of pipes with the standard trench width and depth as per standard specification

63 mm OD PVC pipes

Supply of UPVC Rigid pipes and specials

63 mm OD PVC pipes

63 mm pvc bend

63 mm pvc Tee

63 mm x 50 mm PVC Threaded coupler

Supply of unplasticised GI pipes and specials as per as per IS 1239/PART II Specification FOR CULVERT/ ROAD crossing portion

50 mm GI Pipe

50 mm GI coupling

50 mm GI Elbow

Conveying the PVC pipes and specials to trench, Lowering PVC rigid pipes and specials to trench and laying to proper grade and alignment, jointing with PVC couplers with cement paste including testing.

50 mm GI pipe

63 mm OD PVC pipes

Refilling with excavated soil complying with standard specification in layers of 15cm thick well rammed and consolidated after the pipes and specials are laid and tested

63 mm OD PVC pipes

Provision for gate value 80 mm

Testing of pipes20%

30,000ltr OHT

Earth work excavation and initial lift of 2m in hard stiff clay, stiff black cotton soil, hard red earth, earth mixed with small sized boulders and hard gravelly soil as per SS 20B

First Depth

Second depth

Supply, Delivery and Filling with clean M sand complying with standard specification including watering ramming and consolidation etc., complete and as directed by TWAD Board Officers-for foundation.

Levelling coarse in cement concrete 1:4:8 (one cement,four sand and eight aggregate) using 40mm hard broken stone and M Sand for foundation and leveling coarse including cost of all materials, mixing,placing, ramming, curing, finishing etc., complete and as directed by TWAD Board Officers. (Beyond 1.5 m to 4.5 m below GL)

Reinforced Cement Concrete using M30 Design mix with required cement, sand and 20 mm and 10 mm Machine crushed HBG stone with M Sand including the cost of all materials, labour charges, mixing by using mechanical mixer machine, placing in position, lifting, vibrating by using mechanical vibrator, finishing & curing but excluding the cost of reinforcement and fabricating, centering, shuttering and strutting charges etc., complete and as directed by TWAD Board Officers.

For items 1.5m to 4.5m below GL

For items 0 to 1.50m below GL

For items 0m to 4.5m above GL

For items 4.51m to 7.32 m above

For items above 7.32 m & up to 10.98 m from GL

For items above10.98 m & up to 14.64 m from GL

Reinforced Cement Concrete using M30 Design mix with required cement, sand and 20 mm and 10 mm Machine crushed HBG stone with M Sand including the cost of all materials, labour charges, mixing by using mechanical mixer machine, placing in position, lifting, vibrating by using mechanical vibrator, finishing & curing but excluding the cost of reinforcement and fabricating, centering, shuttering and strutting charges etc., complete and as directed by TWAD Board Officers.

For items above10.98 m & up to 14.64 m from GL

For items above14.64 m & up to 18.30 m from GL

Supplying and erecting centering shuttering including necessary supports for plane surface in foundation and basement and in all floors for R C C column footing column plinth beam, beams, roof slabs, staircase steps, bed blocks, critical pier etc

Below GL

Curved Surface - 0 to 3.30m

Square column

Below G.L.

Ground level to 3.30 m

Painting two coats with approved cement paint best quality over the plastered surface including cleaning preparing the surface , curingetc complete the quality , shade/colour of paing shall be got approved by the executive engineer

Supplying fabricating and placing in position of RTS steel rods for reinforcement for various members including cost of steel and binding wire for all RCC works as directed by the officers

Fabrication, supply, delivery and fixing of outside MS ladder 45cm clear wide made out of 50mm x 50mm x 6mm MS angle for both sides and for s teps at 30cm C/C welded ;joint etc for 1st staging from ground level to first level brace ,( weight 4.50 KG/M) second and third staging upto floor slab and 4th staging from floor slab to roof top supply and delivery , fixing of 32mm GI pipes, medium for hand rails from 1st stage to 4th stage. RCC M30 grade mix for landing slabs - 5Nos. ( ground level - 1No. and above ground level - 4 Nos.) supply and fixing of 32mm GI pipes medium for hands raise for the landing slab. supply and fixing MS base plate of 100mm x 100mm x 6mm thick for anchor fastener bolt for fixing of hand rails at landing slab and MS ladder, providing locking arrangements with two coats of approved enemel paint over one coat of red axide paint as per approved type design and as directed by the officers

Providing and fixing RCC inside access ladder in RCC 1:1.5:3 using 20mm metal including all charges

Providing GI Ventilating arrangements with mosquito proof net etc., complete and as directed by TWAD Board officers.

50 mm G.I. Pipe

50 mm G.I. Tee

50 mm G.I.Hex Nipple

50 mm G.I. Elbow

Providing Cut stone slab in CM 1:3 mix using well dressed cut stone supportin;g inlet pipe inside the tank and as directed by Departmental Officers

supply, delivery and fixin;g in position of CI manhole cover and frame of size 60x60cm on roof slab and as directed by the officers. The Manhole frame and cover should be of light duty and conforming to IS 1726/1974.

Painting emblem and writing slogans and details of scheme on the exposed surface of SR of side wall in approved colour and paint as directed by the officers including cost of paint , brush, scoffolding etc, complete

Provision for pipe connection arrangements including civil works

65mm Ø GI pipes for inlet 1xl connection

65mm Ø GI pipes for over flow

50mm Ø GI pipes for scour pipe 1xl

65mm Ø GI pipe for delivery 1x1 pipe

90mm Ø PVC Threaded coupler

75 mm Ø PVC threaded coupler

65mm Ø GI Tee

65mm Ø GI 90 Bend

65mm Ø GI coupler

65mm Ø GI union

65mm Ø GI Elbow

65x50mm Ø GI Reducer

75mmx 63mm PVC Reducer coupler

75mm PVC Threaded coupler

90x75 PVC Reducer (Fabricated)

75x63 PVC Reducer (Fabricated)

65mm Ø GM Gate valve

50mm Ø GM gate valve

Refilling excauvated soil in layer of not more than 15 cm thick

HSC Connection in DI Mains for Water Supply Scheme - Providing suitable dia non corrosive engineering plastic moulded Clamp Saddle with SS 304 threaded metal inserted for tapping outlet suiting for ½”, 3/4” &1” clear bore and with wide plastic strap (Engineering Plastic) with SS 304 suitable bolts & nuts. Saddle to have sealing of Thermo plastic elastomeric (TPE) material around. (20mm)

Common Items for HSC Connection - Brass Ferrule as per IS 319 grade of sizes 15mm, 20mm and 25mm size and threaded as per IS:1554 BSPT, ISO:7-1 to suit the corresponding bore sizes of 15mm, 20mm and 25mm dia size ( 1/2", 3/4" and 1") in the saddle Connection as per IS :1554 BSPT, ISO:7-1 (15mm)

Poly Propylene compression Female Threaded Adaptor with metal insert of SS 304 as per standards ISO 14236 and Tested as per BS 6920 in WRC-NSF LTD, UK for connecting 15mm, 20mm and 25mm outlet points of Brass ferrule of sizes 15mm, 20mm and 25mm respectively. (20mm)

Poly propylene 90 Degree Compression elbow with compression joint at both ends as per standards ISO 14236 and Tested as per BS 6920 in WRC-NSF LTD, UK suitable for 20mm, 25mm and 32mm OD MDPE pipes (20mm)

Poly Propylene compression Female Threaded Elbow with metal insert of SS 304 as per standards ISO 14236 and Tested as per BS 6920 in WRC-NSF LTD, UK suitable for 20mm, 25mm and 32mm OD MDPE pipes (20mm)

Poly Propylene compression Male Threaded Adaptor with metal insert of SS 304 as per standards ISO 14236 and Tested as per BS 6920 in WRC-NSF LTD, UK suitable for 20mm, 25mm and 32mm OD MDPE pipes (20mm)

MDPE PE 80 PN16 Blue pipe as per standards ISO 4427 and Tested as per BS 6920 in WRC-NSF LTD, UK (20mm)

Earthwork Excavation for 20mm PVC pipe laying work including cost of Refilling work as per Standard Specifications 20B (in Rm)

Labour Charges for Laying & Jointing 20 mm pipe in Excavated Trench in Proper Camber

Supply & Laying & Jointing 20 mm PVC Elbow (Mould) BIS 7834/1975 Part V for Tap Connection

Supply & Laying & Jointing 20 mm brass tap

U PVC ball valve with one side compression end and other side female end as per ISO 4422-4 and Tested as per BS 6920 in WRC-NSF LTD, UK,size : 20mm ODx1/2"ID, 25mm ODX1/2"ID and 32mm OD X 3/4" ID - 20mm

50mm GI Saddle piece

Labour charges for Drilling,Cutting and fixing ferrules in distribution line

Supply and delivery of the MS clamp and fixing in wall in open space with required screw etc

cutting MDPE Pipes and specials true axis and finishing the end complete

Providing Borewell, Pumpset, Pumping Main,Distribution Line & FHTC in Valukalotti Village & panchayat In Kariapatti Block

Borewell

Charges for conducting Geophysical survey for identifying the favourable drilling point

Drilling of 6'' Dia bore well in soft rock area including trench protection charges etc., complete.Clay Soil

Drilling of 6'' Dia bore well in hard rock area including trench protection charges etc., complete.Hard Soil

Supply & delivery of 150mm Dia PVC Plain Casing pipe as per IS 12818 / 2010

Pumpset

Supply and delivery of clear water vertical wet type submersible pumpset suitable for 150mm dia borewell conforming to IS 8034/2002 as amended thereafter and BEE 3 Star Rated capable of discharging noted LPM against head of water column due to all causes. The pump shall be with stainless steel shaft and dynamically balanced bronze or Cast SS impeller, brass screws and CI FG 200 grade pump bowl/diffuser with ISI mark. The pump shall be directly coupled to a continuos rated two pole suitable wet type vertical squirrel cage induction motor as per IS9283 /1995 as amended there after, suitable for operation in AC three phase 415 V+/- 10 %, 50 HZ +/- 5 %

Supply and delivery of direct online starter confirming to IS13947 and IEC60947-1 suitable KW rating for operation in AC/Three Phase/50HZ(± 5%) and 415 V(±10%) including Ammeter, Voltmeter, Thermal Overload relay, 16 Amps 2 pole Magnetic Contactor with under Voltage protection, Indication lamp, starting capacitor, running capacitor and On/Off Push button switches, 5 way connector, wiring with 1 sq. mm/1.5 sq. mm copper PVC insulated cable, powder coated vermin proof box including the capacitor (the cost of capacitor is to be taken separately).

Supply, delivery of 1.1 KV Grade,PVC insulated and sheathed 3 core flat copper submersible cable with ISI marking conforming of IS 694/1990 of reputed make for submersible motor erected in borewell. 4 sqmm submergible cable

Supply and delivery of GI medium class pipes and specials as per relevant IS as listed below.

50mm GI Pipe

50mm GI Coupling Heavy

50mm GI Elbow Heavy

50mm GI Union Heavy

50mm GI Flange set Heavy

50mm MS Clampset Heavy

50mm GM Non Return Valve

50mm GM Gate Valve

75mm x 50mm PVC Threaded Coupler

Lighting the pumpromm including internal wiring with switch circute fuses etc. with the following light fittings with ISI marking.

40W box type tube light - 1 No.

100W bulb with angle holder

100W bulk head fittings

5 AMPS 3 pin socket with switch

5 Amps switches for light(Flush type)

Providing lighting wiring using MS conduit pipes and specials with 2 runs 1.5 sqmm PVC copper wire and 1 run 12 swg GI wire for earthing for light, fans and 5A plug points etc.,

Obtaining power supply including cost of following materials and by engaging B licence holder.EB fee for application form and deposit amount will be borne by the Board

Aerial fuse board of size 15 x 10 x 6cm with 32 A aerial fuse carrier(3 Nos.)

Wall mounting type MS cubical EB meter box with fuse carrier (3 Nos) of 32 A capacity at EB supply point.This box is also to accommodate TNEB energy meter with proper ventilation as approved by TNEB.

Supply and laying of 7/20 size PVC insulator copper conductor cable from Aerial fuse to EB supply point etc., complete as per I.E Rules.

25mm dia GI pipe for service point

25mm dia GI Elbow

No.8 GI wire for earth(Twin earthing)

Stay wire 7/20

20mm GI pipe for twin earthing and cable encasing

4way nutral link

TW banel board (41 x 31 x 6cm)

Labour charges for erection of submersible pump set including fixing and jointing the submersible cable with clamps to the required depth, valves and errection panel board control room twin earthing as per I.E Rules including cost of civil works

Upto 5 HP

Main line

Earthwork excavation in all type of Soil strata for laying of pipes with the standard trench width and depth as per standard specification

Supply of unplasticised PVC rigid pipes and specials as per IS 4985 / 2000 Specification

75mm OD pvc pipes - 4KSC

75 mm pvc bend

75 mm pvc Tee

75 mm x 50 mm PVC Threaded Coupler

Single Air valve

Supply of unplasticised GI pipes and specials as per as per IS 1239/PART II Specification FOR CULVERT/ ROAD crossing portion

65 mm GI Pipe

65 mm GI bend

65 mm GI coupling

65 mm GI Elbow

Conveying the PVC pipes and specials to trench, Lowering PVC rigid pipes and specials to trench and laying to proper grade and alignment, jointing with PVC couplers with cement paste including testing. .

65 mm GI pipe

75mm OD pvc pipes - 4KSC

Refilling with excavated soil complying with standard specification in layers of 15cm thick well rammed and consolidated after the pipes and specials are laid and tested

Testing of pipes20%

Distribution line

Earthwork excavation in all type of Soil strata for laying of pipes with the standard trench width and depth as per standard specification

63 mm OD PVC pipes

Supply of UPVC Rigid pipes and specials

63 mm OD PVC pipes

63 mm pvc bend

63 mm pvc Tee

63 mm x 50 mm PVC Threaded coupler

Supply of unplasticised GI pipes and specials as per as per IS 1239/PART II Specification FOR CULVERT/ ROAD crossing portion

50 mm GI Pipe

50 mm GI coupling

50 mm GI Elbow

Conveying the PVC pipes and specials to trench, Lowering PVC rigid pipes and specials to trench and laying to proper grade and alignment, jointing with PVC couplers with cement paste including testing.

50 mm GI pipe

63 mm OD PVC pipes

Refilling with excavated soil complying with standard specification in layers of 15cm thick well rammed and consolidated after the pipes and specials are laid and tested

63 mm OD PVC pipes

Provision for gate value 80 mm

HSC Connection in DI Mains for Water Supply Scheme - Providing suitable dia non corrosive engineering plastic moulded Clamp Saddle with SS 304 threaded metal inserted for tapping outlet suiting for ½”, 3/4” &1” clear bore and with wide plastic strap (Engineering Plastic) with SS 304 suitable bolts & nuts. Saddle to have sealing of Thermo plastic elastomeric (TPE) material around. (20mm)

Common Items for HSC Connection - Brass Ferrule as per IS 319 grade of sizes 15mm, 20mm and 25mm size and threaded as per IS:1554 BSPT, ISO:7-1 to suit the corresponding bore sizes of 15mm, 20mm and 25mm dia size ( 1/2", 3/4" and 1") in the saddle Connection as per IS :1554 BSPT, ISO:7-1 (15mm)

Poly Propylene compression Female Threaded Adaptor with metal insert of SS 304 as per standards ISO 14236 and Tested as per BS 6920 in WRC-NSF LTD, UK for connecting 15mm, 20mm and 25mm outlet points of Brass ferrule of sizes 15mm, 20mm and 25mm respectively. (20mm)

Poly propylene 90 Degree Compression elbow with compression joint at both ends as per standards ISO 14236 and Tested as per BS 6920 in WRC-NSF LTD, UK suitable for 20mm, 25mm and 32mm OD MDPE pipes (20mm)

Poly Propylene compression Female Threaded Elbow with metal insert of SS 304 as per standards ISO 14236 and Tested as per BS 6920 in WRC-NSF LTD, UK suitable for 20mm, 25mm and 32mm OD MDPE pipes (20mm)

Poly Propylene compression Male Threaded Adaptor with metal insert of SS 304 as per standards ISO 14236 and Tested as per BS 6920 in WRC-NSF LTD, UK suitable for 20mm, 25mm and 32mm OD MDPE pipes (20mm)

MDPE PE 80 PN16 Blue pipe as per standards ISO 4427 and Tested as per BS 6920 in WRC-NSF LTD, UK (20mm)

Earthwork Excavation for 20mm PVC pipe laying work including cost of Refilling work as per Standard Specifications 20B (in Rm)

Labour Charges for Laying & Jointing 20 mm pipe in Excavated Trench in Proper Camber

Supply & Laying & Jointing 20 mm PVC Elbow (Mould) BIS 7834/1975 Part V for Tap Connection

Supply & Laying & Jointing 20 mm brass tap

U PVC ball valve with one side compression end and other side female end as per ISO 4422-4 and Tested as per BS 6920 in WRC-NSF LTD, UK,size : 20mm ODx1/2"ID, 25mm ODX1/2"ID and 32mm OD X 3/4" ID - 20mm

50mm GI Saddle piece

Cutting of old CC road for laying the 20mm pvc pipe

Labour charges for Drilling,Cutting and fixing ferrules in distribution line

Supply and delivery of the MS clamp and fixing in wall in open space with required screw etc

cutting MDPE Pipes and specials true axis and finishing the end complete

GST Amount for providing Service to above Government Contract Works. { GST Amount is the Total GST Amount for total overall quoted amount above this row in column "BB" for all works in this package}