81452 REPAIRS TO STEEL AND WOODEN FURNITURE AT INS KATTABOMMAN UNDER GE TIRUNELVELI

Amount

SCH 'A' PART -I STEEL FURNITURE

CHARPOY GI PIPE WITH PLY TOP, IP FD-220,FD/E6/MAP-II/01

Removing the existing unserviceable/broken damaged ply top from Charpoy GI pipe with ply top and supply and fix new plywood top (BWR Grade, IS 303) in iron stiffener of charpoy GI through nut , bolt and washer according to the size of the charpoy and stiffener shall be painted with 02 coats of synthetic enamel paint in black colour over a coat of red oxide primer.

Supply and fix long rail of 32 mm bore GI pipe medium grade duly threaded on both sides having length 1884 mm.

M & L for cutting the long rail of 32mm bore GI pipe obtained from Ser No 2.02 above and modifying into short rail having minimum length of 804 mm and threading both ends as specified in the drg,

Cutting and modifying the dismantled short rail into legs. The length of leg shall be 377mm including threading and providing wooden plugs as specified in the drg.

Supply and fix three way elbow GI 32 mm bore ISI marked of weight not less than 400 gms .

Supply and fix check nut 32 mm dia of weight not less than 100 gms each for connecting elbows.

Preparation of old painted steel surface of charpoy IP with hard top and applying one coat of black synthetic enamel paint.

Supply and fix new rubber toes (Set of 04 Nos) to the legs of charpoy GI Pipe with plytop

CHAIR CB STEEL WITH ARM (FD-75(M)

Removing the existing u/s wooden seat frame and replace with new seat frame made out of 1st class hard wood 40 x 25 mm (TS) duly drilled and painted with two coats of Synthetic enamel paint black colour. The frames are to be fixed to the tubular conduit frame, using steel screws and including provision of 04 Nos PVC shoes of approved quality.

Removing the existing u/s wooden back frame and supply and fix new back frame made out of 1st class hard wood 40 x 25 mm (TS) duly drilled and painted with two coats of Synthetic enamel paint black colour. The frames are to be fixed to the tubular conduit frame, using steel screws and including provision of 02 Nos PVC caps to top end of MS pipe frame of approved quality.

Removing the existing u/s broken arm rest wooden of chair, supply and fix new well seasoned 1st class hard wood arm rest of size 400 x 50x20 mm made to shape and painted with two coats of synthetic enamel paint , fixed with steel screws from the bottom of the tubular frame all as specified and shown in drg.

Removing the old rusted flat iron support at bottom and back of seat and replacing with new flat iron 20x3mm , 500mm long 02 Nos each at bottom and back having machine drilled hole at ends including inserting MS screws of 30mm including fixing of Flat iron support to the steel frame by welding as shown in drg .

Preparation of old painted steel surface of chair CB steel with arm and applying one coat of olive green synthetic enamel paint including removing the rust and carryout the welding to broken portion of steel frame chairs.

CHAIR CB STEEL WITHOUT ARM (FD-75 (M)

Removing the existing U/S wooden seat frame and replace with new seat frame made out of 1st Class hard wood 40 x 25 mm (TS) duly drilled and painted with two coats of Synthetic enamel paint black colour. The frames are to be fixed to the tubular conduit frame, using steel screws and inclduing provision of 04 Nos PVC shoes of approved quality.

Removing the existing u/s wooden back frame and supply and fix new back frame made out of 1st class hard wood 40 x 25 mm (TS) duly drilled and painted with two coats of Synthetic enamel paint black colour. The frames are to be fixed to the tubular conduit frame, using steel screws and including provision of 02 Nos PVC caps to top end of MS pipe frame of approved quality.

Removing the old rusted flat iron support at bottom/back of seat and replacing of with new Flat iron 20x 3mm, 400 mm long, 02 nos each at bottom and back having machine drilled hole at ends for including inserting MS screws of 30mm and fixing the same to the steel frame by welding as shown in drg.

Preparation of old painted steel surface of chair CB steel without arm and applying one coat of olive green synthetic enamel paint including removing the rust and carryout the welding to broken portion of steel frame chairs .

TABLE DINING ORs (FD-165)

Removing existing unserviceable table top from table dining ORs and replacing with new 19 mm particle board of BWR grade having dimensions 1900 x 685 mm as per specification.

Removing existing broken MS Square tube 25 mm from the legs of table dining and replace with one of required length and welding to dining table where ever required all as shown in drg and as directed by engineer –in-charge and applying two coats of synthetic enamel paint black colour over a coat of red oxide primer.

Supply and fix new hard rubber toes (Set of 04 Nos) to the legs for table dining ORs .

CHAIR VERANDAH (FD-19/228/259 & FD/E6/MAP-II/06)

Removing the old U/S cane plastic and removing the old paint /rust from the tubular frames and painting with two coats of synthetic enamel paint .

Recaning the chair verandah with new 4mm wide cane plastic of matt pattern ( as per trade pattern) to seat and back

Repair of Chair verandah by denting /welding etc to fix suitably all as directed and shown on drg.

Removing the broken unserviceable PVC back of Chair verandah and recaning the chair verandah with new 4mm wide cane plastic of matt pattern to seat and back as specified in drawing.

Supply and fix new hard rubber toes (Set of 04 Nos) to the legs of chair verandah .

TABLE OFFICE CLERK STEEL(FD-84/1004,250)

Removing the existing worn out U/S table top, replacing with 18mm thick particle board BWR grade of size 1200x600mm as directed and shown on drg.

Removing the existing U/S locks and supply and fix new lock 50mm size with duplicate key of Godrej/equivalent to godrej make suitable for drawers .

Preparation of old painted steel surface and applying one coat of synthetic enamel paint Olive Green shade internally and externally for table office clk steel .

Repair to steel table drawers by denting /welding etc to fix suitably in the channels all as directed by Engr-in-Charge.

Supply and fix new hard rubber toes (Set of 04 Nos) to the legs of table office clk steel .

TABLE OFFICE OFFICER (FD-1003)

Removing the existing worn out U/S table top replacing with 18 mm thick particle board BWR grade of size 1350x750mm as directed and shown on drg.

Removing the existing U/S locks and supply and fix new lock 50mm size with duplicate key of Godrej/equivalent to Goderj make suitable for drawers .

Preparation of old painted steel surface and applying one coat of synthetic enamel paint Olive Green shade internally and externally for table office officer.

Repair to steel table drawers by denting /welding etc to fix suitably in the channels all as directed by Engr-in-Charge.

Supply and fix new hard rubber toes (Set of 04 Nos) to the legs of table office officer .

ALMIRAH LARGE/MED WITH SHELVES STEEL(FD-67(M).

Removing the existing U/S lock, supply and fix new lock (ISI Marked) along with suitable three way lock of 55/65mm with brass lever with two keys chromium plated for Almirah large with shelves steel .

All as per item No 9.01 above , but for almirah medium with shelves steel .

Removing the existing U/S handle, supply & fix new steel chromium plated handle 125mm long to the steel almirah large/ medium

Preparation of old painted steel surface of Almirah large with shelves and spray painting with one coat of synthetic enamel paint olive green shade on both internal and external surfaces.

All as per item No ser No 9.04 above but for almirah medium with shelves steel.

CHAIR EXECUTIVE REVOLVING(Make-Godrej)

Removing of unserviceable seat of existing TP chair, S & F best quality moulded seat cushions (make- Godrej)of suitable size & material to existing chair as per existing shape and size all as directed by GE/BSO including dismantling.

All as per item No 10.01 above but moulded back cushion

Removing of unserviceable base of existing TP chair, M& L for provision of new base (make- Godrej) of best quality (ISI Marked) as per existing shape and size all as directed by Engr-in-Charge.

Removing of unserviceable cloth of existing TP chair, M& L for provision of new tapestry cloth as in seat / back cushion covers as per existing shape / size all as directed by Engr-in-Charge including dismantling (Cost of tapestry cloth provided shall not be less than 275/- RM)

Removing of unserviceable arms of existing TP chair, Supply and fix new arms (make- Godrej) (Set of 02 Nos) in each chair of 1st quality as per existing shape for chair executive revolving all as directed by Engr-in-Charge including dismantling

Removing of unserviceable Hydraulic systems of existing TP chair, Supply and fix new Hydraulic systems (make- Godrej) best quality (ISI Marked) as per existing of chair executive revolving low back / high back and size as directed by Engr-in-Charge including dismantling.

CHAIR EXECUTIVE CONFERENCE(MAKE -GODREJ)

Removing of unserviceable seat of existing TP chair, S & F best quality moulded seat cushions (make- Godrej)of suitable size & material to chair as per existing shape and size all as directed by GE/BSO including dismantling.

All as per item No 11.01 above but moulded back cushions (make- Godrej)

Removing of unserviceable base of existing TP chair, M& L for provision of new base (make- Godrej) of best quality (ISI Marked) as per existing shape and size all as directed by Engr-in-Charge including dismantling.

Removing of unserviceable cloth of existing TP chair, M& L for provision of new tapestry cloth as in seat / back cushion covers as per existing shape / size all as directed by Engr-in-Charge incuding dismantling (Cost of tapestry cloth provided shall not be less than 275/- RM)

Removing of unserviceable arms of existing TP chair, Supply and fix new arms (make- Godrej) (Set of 02 Nos) in each chair of 1st quality as per existing shape and for chair executive revolving all as directed by Engr-in-Charge including dismantling.

Removing of unserviceable Hydraulic systems of existing TP chair Supply and fix new Hydraulic systems (make- Godrej) best quality (ISI Marked) as per existing chair executive revolving low back / high back and size as directed by Engr-in-Charge including dismantling.

CHAIR VISITOR (Make Godrej)

Removing of unserviceable seat of existing TP chair, Supply and fix new seat (make : Godrej)as per existing shape and size all as directed by GE/BSO including dismantling

All as per item No 12.01 above but moulded back cushion (make : Godrej)

Removing of unserviceable arms of existing TP chair, Supply and fix new arms (Set of 02 Nos)(make : Godrej) in each chair of 1st quality as per existing shape for chair and as directed by Engr-in-Charge including dismantling.

Removing of unserviceable frame of existing TP chair, Supply and fix new frame (make : Godrej) for chair visitor

CHAIR VISITOR (Make Damro)

Removing of unserviceable seat of existing TP chair, Supply and fix new seat (make : Damro)as per existing shape and size all as directed by GE/BSO including dismantling.

All as per item No 13.01 above but moulded back cushion (make : Damro)

Removing of unserviceable arms of existing TP chair, Supply and fix new arms (Set of 02 Nos)(make : Damro) in each chair of 1st quality as per existing shape for chair and as directed by Engr-in-Charge including dismantling

Removing of unserviceable frame of existing TP chair, Supply and fix new frame (make : Damro) for chair visitor.

CHAIR COMPUTER (Make Damro)

Removing of unserviceable seat cushion of existing TP chair, S & F best quality moulded seat cushion (make : Damro)duly covered with new tapestry cloth as per existing shape and size all as directed by GE/BSO including dismantling.

All as per item No 14.01 above but moulded back cushion (make : Damro)

Removing of unserviceable base of existing TP chair, M & L for provision of new base (make : Damro) of best quality (ISI Marked) as per existing shape and size all as directed by Engr-in-Charge including dismantling.

Removing of unserviceable arms of existing TP chair, Supply and fix new arms (Set of 02 Nos) (make : Damro) in each chair of 1st quality as per existing shape for chair and as directed by Engr-in-Charge including dismantling.

Removing of unserviceable Hydraulic system of existing TP chair, Supply and fix new Hydraulic system (make : Damro) best quality (ISI Marked) as per existing chair computer and size as directed by Engr-in-Charge including dismantling.

CHAIR COMPUTER (Make Godrej)

Removing of unserviceable seat cushions of existing TP chair, S & F best quality moulded seat cushion (make : Godrej)duly covered with new tapestry cloth as per existing shape and size all as directed by GE/BSO including dismantling.

All as per item No 15.01 above but moulded back cushion (make : Godrej)

Removing of unserviceable base of existing TP chair, M & L for provision of new base (make : Godrej) of best quality (ISI Marked) as per existing shape and size all as directed by Engr-in-Charge including dismantling.

Removing of unserviceable arms of existing TP chair, Supply and fix new arms (Set of 02 Nos) (make : Godrej) in each chair of 1st quality as per existing shape for chair and as directed by Engr-in-Charge including dismantling.

Removing of unserviceable Hydraulic system of existing TP chair, Supply and fix new Hydraulic systems (make : Godrej) best quality (ISI Marked) as per existing chair computer and size as directed by Engr-in-Charge including dismantling.

CHAIR CONFERENCE(Make Godrej)

Removing of unserviceable seat cushions of existing TP chair, S & F best quality moulded seat cushion (make : Godrej) duly covered with new tapestry cloth as per existing shape and size all as directed by GE/BSO including dismantling.

All as per item No 16.01 above but moulded back cushion (make : Godrej)

Removing of unserviceable base of existing TP chair, M & L for provision of new base (make : Godrej) of best quality (ISI Marked) as per existing shape and size all as directed by Engr-in-Charge including dismantling.

Removing of unserviceable arms of existing TP chair, Supply and fix new arms (Set of 02 Nos) (make : Godrej) in each chair of 1st quality as per existing shape for chair and as directed by Engr-in-Charge including dismantling.

Removing of unserviceable Hydraulic system of existing TP chair, Supply and fix new Hydraulic system (make : Godrej) best quality (ISI Marked) as per existing chair computer and size as directed by Engr-in-Charge including dismantling.

BED HARD STEEL (FD/E6/MAP/08 (R))

Removing of Broken plywood Top and supply and fix new plywood 12 mm thick commercial face with BWR grade (water proofing, IS 303) according to the size and shape as per drawing.

Preparation of old painted steel surface of bed hard steel with shelves and spray painting with one coat of synthetic enamel paint olive green shade on both internal and external surfaces.

Supply and fix new PVC toes (Set of 04 Nos) to the legs of bed hard steel.

RACK SHOE STEEL(FD/E6/MAP/02 (R))

Removing existing broken 3mm dia MS rod from the shelves of rack shoe steel and replace with one of required length and welding to rack shoe steel where ever required all as shown in drg and supply and fix hard rubber toes as directed by Engineer –in-Charge and applying two coats of synthetic enamel paint black colour over a coat of red oxide primer .

LOCKER BEDSIDE STEEL (FD-1029/257)

S & F Piano hinges steel 30 x 780mm long with required screws all as directed.

S & F Aluminium 'D' handle 100mm long with screw & washer, all as directed.

S & F Aluminium Hasp & Staple 75mm with screw, all as directed.

S &F Aluminium rail 18mm dia 300mm long with both socket fixed with screw all as directed.

Preparation of old painted steel surface of locker bed side steel with shelves and spray painting with one coat of synthetic enamel paint olive green shade on both internal and external surfaces, all as specified and directed.

SCH 'A' PART -II WOODEN FURNITURE

BED HARD WITH PLYWOOD TP(FD-246)

Removing existing broken long rail and supply and fix 1st class hardwood well seasoned long rail made to shape as per drg with dimension of 35 mm x 90 mm x 1980 mm.

Removing of Broken plywood Top and supply and fix new plywood 12 mm thick commercial face with BWR grade of size 1800 mm x 900 mm all as per drg.

Preparation of wooden surfaces with emery paper and applying two coats of french polish all as directed by Engineer-in-Charge.

RECANING OF CHAIRS.

Removing the unserviceable / wornout cane plastic and re-canning the chairs of Chair Easy, Chair Writing, Chair dining JCO/ORs, chair D’ Man and stool dressing, with 2 mm plastic cane in centre and beading with 4 mm of white plastic cane superior quality including supply of plastic canes all as specified and shown on drawings.

FOAM WITH/WITHOUT BACK (FD-77/78)

Removal of U/S top plank from existing foam with & w/o back of size 1800x256x 25mm and supply & fixing new teak wood plank top of size 1800x250x25mm duly polished to the existing frame with necessary nuts & bolts as per drg all as specified and as directred by Engr-in-charge.

Removal of U/S back plank from existing of foam with back of size 1800x150x 19mm and supply & fixing new teak wood plank back of size 1800x150x19mm duly polished to the existing frame with necessary nuts & bolts as per drg all as specified and as directed by Engr-in-Charge.

Supply and fix new hard rubber toes (Set of 06 Nos) to the legs of form with & w/o back .

TABLE DINING 8 PERSONS (FD-239)

Removal of existing U/S legs, replacing with new legs made out 1st class hard wood (Teak wood) 60 x60 mm at top 40 x40 mm at bottom 760mm long including providing hard rubber ring screwed, all as directed and shown on drg.

Removing the existing U/S top, supply and fix with new table top 6’ x 3’ made out of 19mm one side teak veneered particle board. With 3 mm thick TW beading alround all as directed and shown on drg .

Removing the existing damaged braces (Side Rails) on the longer side, replace with new 1st class hard wood(TW) size 25 x 100 x 1420mm all as directed and shown on drg.

Removing the existing damaged braces ( shorter rails) on the shorter side, replace with new 1st class hard wood (TW) of size 25 x100x 640 mm all as directed and shown on drg .

Supply and fix new hard rubber ring screwed (Set of 04 Nos) to the legs for table dining 6/8 persons .

TABLE 3'x 2' WITH / WITHOUT DRAWER (FD-224)

Removing the existing U/S top and replacing with new table top 900 x 600 mm, made of 19 mm one side teak veneered particle board with 3 mm thick TW beading duly polished alround all as directed & shown on drawing.

Removal of existing U/S legs replacing with new legs made out 1st class hard wood (Teak wood) 60 x60 mm at top 40 x40 mm at bottom 760mm long including providing hard rubber ring screwed all as directed and shown on drg.

Removing the existing damaged braces (Side Rails) on the longer side, replace with new 1st class hard wood(TW) size 25 x 100 x 1420mm all as directed and shown on drg.

Removing the existing damaged braces ( shorter rails) on the shorter side replace with new 1st class hard wood (TW) of size 25 x100x 640 mm all as directed and shown on drg .

TABLE DINING 1200x900MM (FD-291)

Removing the existing U/S top and replacing with new table top 1200 x 900 mm, made of 19 mm one side teak veneered particle board with 3 mm thick TW beading alround all as directed & shown on drawing. .

Removal of existing U/S legs, replacing with new legs made out 1st class hard wood (Teak wood) 60 x60 mm at top 40 x40 mm at bottom 760mm long including providing hard rubber ring screwed all as directed and shown on drg.

Removing the existing damaged braces (Side Rails) on the longer side, replace with new 1st class hard wood(TW) size 25 x 100 x 1420mm all as directed and shown on drg.

Removing the existing damaged braces ( shorter rails) on the shorter side replace with new 1st class hard wood (TW) of size 25 x100x 640 mm all as directed and shown on drg .

TABLE 900 x 900MM (FD-291)

Removing the existing U/S Top and replacing with new table top 900 x 900 mm made out of 18 mm thick one side teak veneered particle board. with 3 mm thick TW beading duly polished alround all as directed & shown on drawing. .

TABLE WRITING (FD-249,FD-275)

Removing the unserviceable top of table writing and supply and fix new top made out of 18 mm thick prelaminated particle board one side teak veneered and other side white in colour of size 1145x600 mm with 4mm thick teak wood edging alround all as directed & shown on drawing. .

Removing the unserviceable top drawer of table writing and supply and fix new drawer of size 490x370x100 mm made out of sides with 6 mm thick plywood and bottom with 12mm thick teak wood plank as shown in drg and as directed .

Removing the unserviceable bottom shutter of table writing and supply and fix new bottom shutter of size 370x470mm made out of 18 mm thick prelaminated particle board with 4mm thick teak wood edging alround including all fitting & fixtures as shown in drg and as directed .

Removing the unserviceable stiffener of table writing and supply and fix stiffener of size 50x25x1145mm made out of TW as shown in drg duly polished with French polish to give a glossy appearance all as specified.

Removing the unserviceable leg of table writing and supply and fix new leg of size 55x35x760mm made out of TW duly grooved 5 mm x 5mm in top as shown on drg duly polished with French polish to give glossy appearance all as specified and as directed .

Removing the unserviceable plywood, back of drawer and supply and fix new plywood 6mm thick of size 410x610mm all as shown in drg and as directed .

Removing the unserviceable side portion of drawer and supply and fix new side portion made out of 18 mm thick ply wood one side TW veneered and other side commercial of size 610x560mm with 4mm thick TW beading alround as shown in drg duly French polished over TW edging .

Supply and fix new hard rubber ring screwed (Set of 04 Nos) to the legs for table writing.

TABLE DRESSING LADIES (FD/MAP/II/07)

Removing of unserviceable old defaced mirror and unserviceable back ply wood of mirror frame of table dressing ladies and providing new sheet glass electro copper plated mirror 5mm thick and new plywood commercial BWR grade 6mm thick ply for back side of mirror frame and fixing to table dressing ladies including French polishing to frame all as directed and specified and shown on drg.

Removing of unserviceable/chipped/old 18mm thick Pre laminated particle board of size 450 x 380 and fix new pre laminated particle board 18mm thick of size 450 x 380mm on the top of dressing table between the drawer all as shown on drg.

Repairs to dressing table Ladies drawers to fix suitably in the channels all as directed by Engineer-in-charge.

SIDE BOARD (FD-26,FD-241)

Removing the unserviceable door of side board and supply and fix new 18mm thick prelaminated particle board natural TW shade one side and other side white in two parts of size 835 x 655mm including fixing of piano hinges, knobs ,locks etc all as shown in drg and as directed.

Removing the unserviceable particle board of side portion of side board and supply and fix new 18 mm thick prelaminated particle board one side natural thick and other side white of size 455x625mm all as shown in drg and as directed.

Removing the unserviceable plywood from back side of side board and supply and fix new ply wood of size 625x1100mm , 6 mm thick all as shown in drg and as directed.

Removing the unserviceable legs with frame of side board and supply and fix new frame of size 1050x360mm made out of TW stiffeners of size 25x45mm all around with 4 nos legs made out of 45x45mmx125mm on top and 25x25x125mm at bottom all as shown in drg and as specified .

Removing the unserviceable drawers of side board and supply and fix new drawer sets consisting of 04 nos all as shown in drg and as specified and as directed . (04 nos of drawers will be measured as a single unit)

Removing the unserviceable bottom of side board and supply and fix new bottom made out of 18 mm thick pre laminated particle board both side commercial of size 1220x460mm all as shown in drg and as directed .

Removing the unserviceable top of side board and supply and fix new top board made out of 18 mm thick particle board one side teak face of size 1220x460mm all as shown in drg and as directed .

CHAIR DINING (FD-228,FD-279 & FD/E6/MAP-II/04)

Removing the existing unserviceable rear leg from chair Dining and Supply and Fix new Teak wood Rear leg of size 35x50 mm made to shape all as shown on drg duly polished with French polish to give a glossy appearance all as specified and as directed .

Removing the existing unserviceable front leg from chair dining and supply fix new TW front leg of size 35x50 mm made to shape all as shown on drg and as specified duly polished with French Polish to give a glossy appearance all as specified and as directed.

Removing the existing unserviceable side rail from chair dining and supply and fix new TW side rail of size 25x65 mm made to shape all as shown on drg duly polished with French polish to give a glossy appearance all as specified and as directed .

Removing the existing unserviceable rear rail from chair dining and supply and fix new TW rear rail of size 25x65 mm made to shape all as shown on drg duly polished with French polish to give a glossy appearance all as specified and as directed .

Removing the existing unserviceable stiffner from chair dining and supply and fix new TW stiffner of size 20x25x430mm made to shape all as shown on drg duly polished with French polish to give a glossy appearance all as specified and as directed .

Removing the existing unserviceable broken top rest from chair dining and supply and fix new TW top rest of size 45x15x440mm made to shape of size 45x35x440 mm all as shown on drg duly polished with French polish to give a glossy appearance all as specified and as directed .

Removing the old unserviceable ply top with cushion from the chair dining officers and supply and fix new 12mm ply top with cushion 75mm thick and 40 density foam with fabric cushion covered with long cloth and shall be tapestry cover of quality not less than Rs. 275 per mtr as specified in drg and approved by GE/BSO

Supply and fix nylon buffer (Set of 04 Nos) to the legs of chair dining .

CHAIR EASY (FD-229& FD-17)

Removing the existing unserviceable broken front leg from chair easy and supply and fix new TW front leg of size 55x25x490 mm made to shape all as shown on drg duly polished with French polish to give a glossy appearance all as specified and as directed .

Removing the existing unserviceable broken rear leg from chair easy and supply and fix new TW rear leg of size 55x20x490 mm made to shape all as shown on drg duly polished with French polish to give a glossy appearance all as specified and as directed .

Removing the existing unserviceable broken front rail from chair easy and supply and fix new TW front rail of size 55x25x510mm made to shape all as shown on drg duly polished with French polish to give a glossy appearance all as specified and as directed .

Removing the existing unserviceable broken rear rail from chair easy and supply and fix new TW rear rail of size 55x25x490mm made to shape all as shown on drg duly polished with French polish to give a glossy appearance all as specified and as directed .

Removing the existing unserviceable broken side frame from chair easy and supply and fix new TW side frame of size 70x40x545mm made to shape all as shown on drg duly polished with French polish to give a glossy appearance all as specified and as directed .

Removing the existing unserviceable broken arms from chair easy and supply and fix new TW arms of size 65x25x610mm made to shape all as shown on drg duly polished with French polish to give a glossy appearance all as specified and as directed .

Removing the existing unserviceable broken back rest from chair easy and supply and fix new TW back rest of size 480x510mm made to shape all as shown on drg duly polished with French polish to give a glossy appearance all as specified and as directed .

Supply and fix new hard rubber ring screwed (Set of 04 Nos) to the legs for chair easy .

TABLE PEG(FD-277/236)

Removing of unserviceable/broken top of table peg and providing new top 18 mm thick prelaminated particle board teak shade duly polished and exterior grade with 3mm thick teak wood edging all round duly fixed all as specified, directed and shown on drg.

Removing unserviceable broken legs and providing new legs made out of teak wood for table peg duly polished all as directed specified and as shown on drg.

Removing unserviceable broken side short rail and providing new side short rail made out of hard wood for table peg all as directed and shown on drg.

Removing unserviceable broken side long rail and providing new side long rail made out of hard wood for table peg duly polished all as directed and shown on drg.

TABLE CENTRE (FD-235/375)

Removing of unserviceable/broken top of table centre and providing new top 18 mm thick prelaminated particle board teak shade exterior grade with 3mm thick teak wood edging all round duly fixed and duly polished all as specified, directed and as shown on drg.

Removing unserviceable broken legs and providing new legs made out of teak wood for table centre duly polished all as directed specified and as shown on drg.

Removing unserviceable broken side short rail and providing new side short rail made out of hard wood for table centre duly polished all as directed and shown on drg.

Removing unserviceable broken side long rail and providing new side long rail made out of hard wood for table centre all as directed and specified on drg.

TABLE CENTRE (MAKE-DAMRO)

Removing of unserviceable/broken top of table centre and providing new top 18 mm thick prelaminated particle board teak shade exterior grade with 3mm thick teak wood edging all round duly fixed and duly polished all as specified and directed and as shown on drg.

Removing unserviceable broken legs and providing new legs made out of teak wood for table centre duly polished all as directed and shown on drg.

Removing unserviceable broken side short rail and providing new side short rail made out of hard wood for table centre duly polished all as directed and shown on drg.

Removing unserviceable broken side long rail and providing new side long rail made out of hard wood for table centre duly polished all as directed and shown on drg.

COMPUTER TABLE (DAMRO)

Removal of existing U/S side wooden frame, replacing with new frame made out 1st class hard wood with 3 mm thick TW beading all around all as directed and shown on drg.

Removing the existing U/S top, supply and fix with new computer table top 4’ x 2’ made out of 19 mm one side teak veneered particle board with 3 mm thick TW beading all as directed and shown on drg .

Removal of existing U/S bottom wooden frame replacing with new frame made out 1st class hard wood with 3 mm thick TW beading all around all as directed and shown on drg.

Removal of existing U/S wheel and replacing with new wheel, all as directed and shown on drg.

TEAPOY WOODEN (FD-232)

Removing of unserviceable/broken top of Teapoy wooden duly polished and providing new top 18 mm thick prelaminated particle board teak shade exterior BWR grade with 3mm thick teak wood edging all round duly fixed all as specified, directed and shown on drg.

Removing unserviceable broken legs and providing new legs made out of teak wood for teapoy wooden duly polished all as directed, specified and as shown on drg.

Removing unserviceable broken side short rail and providing new side short rail made out of hard wood duly polished for teapoy wooden all as directed and shown on drg.

Removing unserviceable broken side long rail and providing new side short rail made out of hard wood duly polished for teapoy wooden all as directed and shown on drg.

TEAPOY (DAMRO)

Removing of unserviceable/broken top of Teapoy (Make-DAMRO) and providing new top 18 mm thick prelaminated particle board teak shade exterior BWR grade with 3mm thick teak wood edging all round duly fixed all as specified and directed.

Removing unserviceable broken legs and providing new legs made out of teak wood for teapoy (Make-DAMRO) duly polished all as directed specified.

Removing unserviceable broken side short rail and providing new side short rail made out of hard wood duly polished for teapoy(Make-DAMRO) all as specified and directed.

Removing unserviceable broken side long rail and providing new side long rail made out of hard wood duly polished for teapoy (Make-DAMRO) all as specified and specified.

TABLE BEDSIDE (FD/E6/MAP-II/15(R)

Removing unserviceable MS Handles and providing new MS Handles for Table bedside all as directed and shown on drg.

Removing unserviceable PVC Shoes and providing new PVC Shoes (Set of 04 Nos) for Table bedside all as directed and shown on drg.

TABLE BEDSIDE (FD-248)

Removing unserviceable broken top and providing new top 18mm/19mm thick prelaminated particle board teak shade exterior grade for table bed side all as directed, specified and shown or drg.

Removing unserviceable broken back of table bed side and providing new 6mm thick ply wood duly polished according to the shape and size of table bed side all as shown on drg.

SOFA SET SINGLE SEATER (FD-258/234/281)

Removal of old unserviceable seat and back cushion of sofa set and providing new seat and back cushion of 40 density foam 100mm thick covered with long cloth and shall be tapestry cover of quality not less than Rs. 380 per mtr all as shown on drg and approved by GE/BSO

Preparation of wooden surface with emery paper and applying two coats of french polish all as directed by Engineer-in-Charge.

SOFA SET SINGLE SEATER (make-Godrej)

Removal of old unserviceable seat and back cushion of sofa set and providing new seat and back cushion (make- Godrej) of 40 density foam 100mm thick covered with long cloth and shall be tapestry cover of quality not less than Rs. 380 per mtr all as shown on drg and approved by GE/BSO.

Preparation of wooden surface with emery paper and applying two coats of french polish all as directed by Engineer-in-Charge.

SOFA SET TWO SEATER (FD-258/234/281)

Removal of old unserviceable seat and back cushion of sofa set and providing new seat and back cushion of 40 density foam 100mm thick covered with long cloth and shall be tapestry cover of quality not less than Rs. 380 per mtr all as shown on drg and approved by GE/BSO.

Preparation of wooden surface with emery paper and applying two coats of french polish all as directed by Engineer-in-Charge.

SOFA SET THREE SEATER (FD-258/234/281)

Removal of old unserviceable seat and back cushion of sofa set and providing new seat and back cushion of 40 density foam 100mm thick covered with long cloth and shall be tapestry cover of quality not less than Rs. 380 per mtr all as shown on drg and approved by GE/BSO.

Preparation of wooden surface with emery paper and applying two coats of french polish all as directed by Engineer-in-Charge.

SOFA SET THREE SEATER (Make- Damro)

Removal of old unserviceable seat and back cushion of sofa set and providing new seat and back cushion (make- Damro) of 40 dencity foam 100mm thick covered with long cloth and shall be tapestry cover of quality not less than Rs. 380 per mtr all as shown on drg and approved by GE/BSO.

Preparation of wooden surface with emery paper and applying two coats of french polish all as directed by Engineer-in-Charge.

SOFA SET FOUR SEATER (Make- Godrej)

Removal of old unserviceable seat and back cushion of sofa set and providing new seat and back cushion (make- Godrej) of 40 density foam 100mm thick covered with long cloth and shall be tapestry cover of quality not less than Rs. 380 per mtr all as shown in drg and approved by GE/BSO.

Preparation of wooden surface with emery paper and applying two coats of french polish all as directed by Engineer-in-Charge.

SOFA SET FIVE SEATER (Make- Godrej)

Removal of old unserviceable seat and back cushion of safa set and providing new seat and back cushion (make- Godrej) of 40 density foam 100mm thick covered with long cloth and shall be tapestry cover of quality not less than Rs. 380 per mtr all as shown on drg and approved by GE/BSO

Preparation of wooden surface with emery paper and applying two coats of french polish all as directed by Engineer-in-Charge.

BIN LINEN MULTIPURPOSE (FD/E6/MAP/09)

Removing the unserviceable door of side board and supply and fix new 18mm thick prelaminated particle board natural teak shade one side and other side white in two parts of size 750 x 450 mm including fixing of piano hinges, knobs etc as shown in drg and as directed.

Removing the unserviceable particle board of side portion of Bin soil linen multipurpose and supply and fix new 18 mm thick prelaminated particle board one side natural teak and other side white of size 750 x 450 mm all as shown in drg and as directed.

Removing the unserviceable plywood from back side of Bin soil linen multipurpose and supply and fix new ply wood of size 1200x750 mm shown in drg and all as directed.

Removing the unserviceable legs with frame of Bin soil linen multipurpose and supply and fix new frame of size 1200x450 mm made out of TW stiffeners of size 75x25mm all around with 4 nos legs made out of 75x45mmx125mm on top and 25x25x125mm at bottom as shown in drg and as specified .

Removing the unserviceable drawers of Bin soil linen multipurpose and supply and fix new drawer sets consisting of 04 nos all as shown in drg and as specified and as directed . (04 nos of drawers will be measured as a single unit)

Removing the unserviceable bottom of Bin soil linen multipurpose and supply and fix new bottom made out of 18 mm thick pre laminated particle board both side commercial of size 1220x460mm all as shown in drg and as directed .

Removing the unserviceable top of side board and supply and fix new top board made out of 18 mm thick particle board one side teak face of size 1220x460mm as shown in drg and as directed .

TABLE DRESSING GENTS (FD-230)

Removing of unserviceable old defaced mirror unserviceable back ply wood of mirror frame of table dressing gents and providing new sheet glass electro copper plated mirror 5mm thick and new plywood commercial BWR grade 6mm thick ply for back side of mirror frame and fixing to table dressing gents including French polishing to frame all as directed and specified and shown on drg.

Removing of unserviceable/chipped/old 18mm thick Pre laminated particle board of size 450 x 380mm and fix new pre laminated particle board 18mm thick of size 450 x 380mm on the top of dressing table between the drawer al as shows on drg and as directed.

Repairs to dressing table Gents drawers to fix suitably in the channels all as directed by Engineer-in-charge.

POLISHING Preparation wooden surface with sand paper and applying two coats of French polish all as directed by Engineer-in-Charge for the following items.

Table bed side MAP

Table 3x2 wooden with and without drawer

Table dining 8 persons

Table Peg

Teapoy Wooden

Table Centre

Chair Easy

Stool dressing

SARGAM ENTERPRISES (BID ID -3470065)

N N J ENTERPRISES (BID ID -3461981)