REPAIRS/REPLACEMENT OF PLUMBING, SANITARY FITTINGS, DOOR, WINDOWS AND OTHER MISC WORKS UNDER GE(MCTE) MHOW

Amount

S&F in repair vitreous china sqatting pan (orissa pattern) size 580mmx440mm, white with integral foot rest, any pattern including provision of cement concrete bedding (excluding fulshing cistern and flush pipe) with S or P trap, Fixed in repairs, complete all as specified and directed

S&F in repairs low level Flushing cistern 10 ltr capacity, PVC valveless syphonic action type, white with inlet, ball valve, float valve and handle , flush pipe, incl brackets and flushing pipe fixed in repairs complete all as specified and directed

S&F in repairs vitreous china,white, wash hand basin, flat back size 550x400mm 'including MS brackets including cutting for and pinning in, including waste pipe complete all as specified and directed

S&F in repair chromium plated brass wall mixer 3-in-1 fancy type with provison for both hand shower and overhead shower complete with wall flange (without hand &over head Shower screwd down for15 mm GI bore pipe complete all as specifed and directed

S&F in repair 20mm dia brass chromium plated tubular towel rails,D type,60cm long between flanges,complete all as specified.

S&F in repair 110 mm dia Cast iron nahani trap with CP grating including including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed

S&F in repair stainless steel kitchen plate rack size 600 x 900 x150 mm of approved pattern made out of stainless steel sheet 0.63 mm thick sheet with round 8mm dia rods including hangine arrangements complete all as specified and as directed.

S&F in repair 15mm size PVC connections internally threaded with PVC washer,PTMT nuts of length 450mm complete all as specified and directed.

S&F Grating 100 mm dia of CP with or without hole complete all as specified and directed.

S&F in repair 15 mm dia bib tap long body cast copper alloy (fency type), chromium plated, with crutch or butterfly handle, screwed down for iron pipe or for brass ferrule complete all as directed.

S&F in repair 125 mm size Brass Chromium plated shower roses with or without swivel joints, any size, including fixing to steel pipe or union complete all as specifed and directed.

S&F in repair 15 mm dia brass chromium plated pillar tap, fancy type with or without lettered 'Hot' or 'Cold' ,with long screwed shanks and fly nut, capstan head, screwed for 15mm dia pipe complete all as directed.

S&F in repairs Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with CP bracket guard & railing 60cm long complete all as directed.

S&F in repair brass CP bottle traps for WHB with inlet and outlet screwed for pipe or connections incl necessary packing union and cap fixed for 32 mm borecomplete all as specified and directed

S&F in repair sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with all plugs, washers, fittings and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm, complete all as specifed and directed.

Taking up or down 15 mm bore steel tubing and connections, including cleaning for re fixing complete all as specifed and directed

S&F, laying and testing for 15 mm bore GI tubing medium grade galvanised steel tubing including all fittings such as union, reducer, sockets, reducing bends elbows tee, checknuts, caps, plugs etc fixed to wall and ceilling or laid in floors complete all as specifed and directed.

S & F in repairs Plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device

S & F in repairs Stop/angle cock 15 mm bore cast copper fancy type chromium plated alloy screwed down high pressure with crutch or butter fly handle serwed both ends for iron pipe or for unions.

S & F in repairs two way Stop/angle cock 15 mm bore cast copper fancy type chromium plated alloy screwed down high pressure with crutch or butter fly handle serwed both ends for iron pipe or for unions.

S&F in repair PVC water tank covers premium quality fitted to tank . Make - Syntex or equivalent water tanks of Cap 500 ltrs to 1000 ltr complete all as specified and directed.

S&F in repair Ball valves 15 mm high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed.

S&F in repair Ball valves 20 mm high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed.

S&F in repair Ball valves 25 mm high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed.

S&F in repair 15 mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed

S&F in repair 20 mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed

S&F in repair 25 mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed

S&F in repairs PVC Type 'S' / 'P' Trap 100 mm size round moulted fitted to Vitreous china, wash down water closet pan (pedestal pattern) all as specifed and directed .

S & F in repairs PVC size 110 x 110 mm Nahani Trap all as specfied and directed .

S&F in repair 1000 litres capacity Rotational moulded polyethylene water storage tanks (Cylindrical vertical with closed top) hoisted and fixed in position including removing the existing water tank all as specified in SSR Part-I

S&F in repair 500ltr capacity rotational moulded polythyiene water storages tanks (cylindrical vartical with closed top) hoisted and fixed in position including removing the existing water tankall as specified in SSR Part-I (complete all as specified and as directed).

Taking down rain water pipes including all fittings any size and pattern.

S &F 110mm bore PVC (SWR) soil, waste and vent pipes single socked in any length with rubber ring joints fixed to walls.

S&F 110mm bore PVC (SWR) bends of any radius.

S&F 110mm PVC (SWR) junction single, (Single T) equal or unequal

S&F 110mm PVC (SWR) branch piece, double (double Y) equal or unequal

S &F 75 mm bore PVC (SWR) soil, waste and vent pipes single socked in any length with rubber ring joints fixed to walls.

S&F 75 mm PVC (SWR) bends any radius

S&F 75 mm PVC (SWR) junction single, (Single T) equal or unequal

S&F 75mm PVC (SWR) branch piece, double (double Y) equal or unequal

Taking down chowkats or frame of any description exc 1.5 Sqm each and n.exc 4Sqm (without taking off shutters from the frames) & remove off the premises complete all as specified and directed.

Taking down Shutters of any description exc 1 sqm but n. exc 2 sq. m each of any description complete all as specified and directed.

Taking down chowkats or frame of any description n.exc. 1.5 Sqm each (without taking off shutters from the frames) & remove off the premises complete all as specified and directed.

Taking down Shutters of any description n. exc 1 sq. m each of any description complete all as specified and directed.

S&F Pressed steel door frame for single door, size 105 x 60mm with one rebates incl necessary fixing lugs, hinges, lock strike plate, holdfast (size 25mm x 3 mm) of length 30 cm) etc., including Cutting holes in brick walls built in cement mortor for inserting holdfasts and making good dismantled portion in cement mortor 1:3 or cement concrete 1:2:4 Type B-1 , depth of embedded portion of holdfasts exc. Half brick but not exc. One brick from the face of the jamb intl the wall complete all as specified and as directed.

S&F Pressed steel door frame for single door, size 165 x 60mm with one rebates incl necessary fixing lugs, hinges, lock strike plate, holdfasts (size 25mm x 3 mm) of length 30 cm) etc., including Cutting holes in brick walls built in cement mortor for inserting holdfasts and making good dismantled portion in cement mortor 1:3 or cement concrete 1:2:4 Type B-1 , depth of embedded portion of holdfasts exc. Half brick but not exc. One brick from the face of the jamb intl the wall complete all as specified and as directed.complete all as specified and as directed.

M & L PCC 1:2:4 type B0(12.5 mm graded) aggregate for filling in pressed steel door framed.

S & F Second class hard wood plain, solid, straight chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue pinned at joints.

S & F 35 mm thick second class hardwood rail and style , Plain, framed, panelled shutters Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated

Solid PVC door frame of size 50mm 47 mm made out of 5mm plain colour PVC sheet rinforced with MS Square tube suppling and fixing in opening as per specification and drawing.

Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S tubes for top & bottom rails. M.S frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip if 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bootom rail on either side & as gap insert for top rail and bottom rail ; Panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles. & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling and fixing in the frame at site as per specification & drawing

S&F 35 mm thick Flush shutters, solid core construction, with block board core & plywood face panels, commercial type on both sides complete all as specified and directed.

S & F 30 mm thick 2nd class hard wood glazed and skeleton shutters open rebated and prepared to receive glass gauge etc with cut and mitred beads for securing glass etc size of member of shutter as specified in SSR Pt-1 section 8 and clause 8.24 (a)

S & F 35 mm thick 2nd class hard wood glazed and skeleton shutters open rebated and prepared to receive glass gauge etc with cut and mitred beads for securing glass etc size of member of shutter as specified in SSR Pt-1 section 8 and clause 8.24 (a)

Providing and fixing of double rebate openable/fixed windows made of galvanized steel colour coated/powder coated (base steel as per IS 513 of “D" quality, galvanized as per IS 277 with zinc of 120 grams/sqm) with total thickness of coating 0.58 microns, primer coated with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with alkyd backer 5-7 microns thick or powder coated with pure polyester powder up to 50-60 microns thick, outer frame section 72 x 55 mm, centre mullion section 72 x 50 mm, shutter section 47 x 20 mm,fly mesh section 40 x 20 mm and the fixed glass beading section 12 x 12 mm, outer frame and mullions shall consists rebate for glazed shutter, fly mesh and 20 mm provision for guard bars/grills, the sections cut to length mitre joined with corner bracket, centre mullions fixed with mullion cap, stay, handles, latch, 2 Nos of heavy duty stainless steel pivot hinges per shutter and panelled with 4mm thick plain float glass and S.S. Mesh for fly mesh shutter (304 grade), fitted using EPDM (Ethyl Propylene Diamine Monomer) gaskets including fixing windows in the concrete/masonry wall by means of self-expanding screws, including 10mm Square bars welded to 6x12mm flat at a distance 150mm c/c (pitch) etc. complete as per the direction of Engineer in Charge. Make NCL window openable shutter

S&F 150 mm size aluminium, anodised barrel tower bolt of extruded section.

S&F 125 mm size aluminium, anodised barrel tower bolt of extruded section.

S&F 300mm length, aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy.

S&F120mm size, butt hinges, heady weight, cold rolled mild steel.

S&F100mm size, butt hinges, medium weight, cold rolled mild steel.

S&F 150mm size extruded aluminium alloy handles, fabricated type.

S&F 125mm size extruded aluminium alloy handles, fabricated type.

M&L for Preparation of new wooden surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer all as specifed and directed.

S&F in repairs 18 mm thick factory made PVC sheet one side pre-laminated sheet ktichen cabinet shutter. The 18mm thick sheet shutter bent at 90 degree and finish all edges at level for marking edge lipping bending for 0.5 mm thick PVC sheet lipping at all four edges using bonding tape etc complete all as per specified and directed by Engr-in-Charge manufactures specification .

S&F Brass handles 100mm size, cast type, polished bright as approved by Engr in Charge complete all as specified and directed

S&F 40 mm dia, brass, knobs for cupboard fixed with nut, screw and washer of mild steel, bright finised complete all as specified and directed.

S&F continuous (piano) hinges, mild steel, bright finish or electrogalvanised with width of flap (when open) 30 mm complete all as specified and directed.

S & F in repair 20mm bore aluminium alloy fancy type any colour curtain rails with brackets and clamps complete all as specified and as directed.

Hacking out old broken glass (any thickness, size, quality or description) from metal frame incl punching or drilling out old glazing pins/spring clips and providing and fixing new ones.

M&L for 4mm thick sheet glass, ordinary quality and glazing with oil putty in steel windows & fixed to wooden window with necessary wooden beeding ,fillets with nails etc in square n exc 0.5 Sqm in each pane.

M&L for 4mm thick sheet figured glass, pin headed type and glazing with oil putty in steel windows & fixed to wooden window with necessary wooden beeding ,fillets with nails etc in square n exc 0.5 Sqm in each pane.

S&F in repairs Galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples

M & L in fixed in repairs 18/19 mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination,fixed with screws to timber frame work

Taking down Shutters of any description exc 2 sq. m each and refixing in the same opening after resecuring or easing and adjusting shutters of any description. complete all as specified and directed.

Taking down shutter exc. 1 Sqm and n.exc 2 Sqm each and refixing in the same opening after resecuring or easing and adjusting shutters of any description. complete all as specified and directed.

S&F in repairs gate shutter hook and eye aluminium plate type II 100 mm size

S & F in repair Aluminium plate type II Gate and shutter, hook & eye 150 mm size

S & F in repair 150 mm long Aluminium, anodised, barrel tower bolts of extruded section

S & F in repair 100 mm long Aluminium, anodised, barrel tower bolts of extruded section

S & F in repaire 150 mm long Extruded Aluminium alloy handles, fabricated type, anodised.

S & F in repaire 100 mm long Extruded Aluminium alloy handles, fabricated type, anodised.

S&F in repairs Helical door spring 300mm, ordinary rat tail rod patttern springs includding roller and roller plate complete

S&F in repaire 150 mm floor door stopper of Aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor

Supply and fix in repair 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast Aluminium alloy.

Preparation of old painted wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying one coat of Synthetic enamel paint (Ordinary tint) upto 15th floor. (Note : Rate shall be included for necessary scaffolding and safety measures where required at site)

Taking down cement or cement lime plaster of any description including racking out joints, hacking for keys , scrubbing down with water etc, complete all as specified and directed.

M&L for Rendering 15 mm thick on fair faces of concrete/brick interior surfaces in cement mortar 1:6 as per manufacturer's instruction, finished fair and even without using extra cement complete all as specified and directed.

M&L preparation of new surfaces pf plastered of walls and applying Two coat of distemper oil emulsion incl priming the surface and incl 1 mm thick wall putty all as directed by Engr-in-Charge .

Providing and fixing pre painted steel sliding window 3-Track, 2 glass panel and 1 mesh panel sliding window fabricated from Roll formed sections made of galvanized Steel colour coated/powder coated (Base Steel as per IS 513 ‘D’ quality, galvanized as per IS 277 with zinc of 120 GM/Sq.mtr) with total coated thickness of 0.58mm. Primer coat with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with Alkyd backer of 5-7 microns or powder coated with pure polyester powder up to 50-60 microns thick. Section for external frame should be of 107x44mm, Section for shutter should be of 35x49mm. Section of mesh should be of 35 x 49 mm.The windows should be paneled with 5mm thick plain float glass. Corner bracket for internal and external frame made of glass filled nylon. Gaskets are to be made of Ethyl Propylene Diamine Monomer (EPDM).The sections are to be cut to length, joined and assembled by means of corner bracket. The above frames should be fixed to the concrete/masonry walls by means of self expanding screws. Make - NCL window three track

Providing and fixing fixed louvers fabricated from Roll formed sections made of galvanized Steel colour coated/powder coated (base Steel as per IS 513 ‘D’ quality, galvanized as per IS 277 with zinc of 120 grams/Sqm) with thickness of 0.58mm coated sections to be primer coat of epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with alkyd backer of 5-7 microns or powder coated with pure polyester powder up to 50-60 microns thick, section for external frame 33 x 58 mm, glass holding flanges made of polypropylene, sections are to be cut to length, mitre joined with corner bracket. The above frames should be fixed to the concrete/masonry walls by means of self expanding screws. Make - NCL ventilator

Dismantling wrought iron or mild steel work of any description not otherwise described complete all as specified and directed

S&F mild steel framed work such as grills, gratings etc with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framed work and similar works complete all as specified and directed.

S & F in repairs factory made PVC shelf/partition of required size consisting of panel of 18 mm thick required size consisting of panel of 18 mm thick celuka PVC ply and for supporting the hold of shelf /partition and shall provided 3 edges in size 18mm x 18 mm as per required lenght the front side of the edge visible in the front of the shelf/partition to be edge lipped by 18mm widht x 1 mm thick PVC sheet of density 600 kg/cum manufactured by ISO 9001-2015 Certified Company , using solvent cement etc.

M&L Brick work with sub class B bricks ,straight or curved on plan exc 6m mean radius built in CM 1:6 Complete all as Specified and directed

M&L Brick work with sub class B bricks, straight or curved on plan to any radius in half brick thick wall built in CM 1:6 Complete all as Specified and directed.

Dismantling floor , hearth or wall tiling including cement mortar bedding (but not backing), removing debrish and rubbish off the premises and stacking serviceable tiles .

M&L for non skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm thick screed bed in CM 1:6

-ditto- but on vertical surfaces such as skirting incl including 10mm thick rendering in cement mortar 1:4 rough finish to receive the tiles complete all as specified and directed.

M&L for glazed coloured ceramic tiles, first quality (or approved class, colour and design/shade) of 350x 250x 7 mm/ 450X 350X 7mm thick in vertical surfaces, as in dado/skirting etc set & jointed in neat cement slurry & pointed in coloured cement to match with coloured tiles, over and including 10mm thick rendering in cement mortar 1:4 rough finish to receive the tiles complete all as specified and directed.

Demolition of un-reinforced Cement Concrete of any description and in any position not otherwise specifically provided for, separation of serviceable materials from the unserviceable, stacking the serviceable materials within 100 M and disposal of unserviceable materials, debris and rubbish to a distance not exceeding 100 M as directed by the Engineer in Charge.

M &L for Cement concrete type B2, 1:4:8 (using 40 mm graded stone aggregate) in foundation filling and mass concrete complete all as specified and as directed.

M&L 25 mm thick PCC 1:2:4 type B1 (Using 12.5 mm graded granite stone aggregate) in path , paving , hardstanding etc, complete all as specified and as directed by Engineer-in-Charge.

M & L coloured Rubber Moulded Chequred Cement Concrete tiles 400 x 400 x 30mm thick, set jointed and pointed in neat cement slurry in floors with grey cement and pigment over and including 15 mm thick screed bed in CM 1:6

M & L coloured Rubber Moulded Chequred Cement Concrete tiles 300 x 300 x 30 mm thick, set jointed and pointed in neat cement slurry in floors with grey cement and pigment over and including 15 mm thick screed bed in CM 1:6

M&L for sand filling under floors or in foundations below interlocking tiles path including watering and consolidation complete all as specified

M & L for Machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness M-40 Grade with grey cement and pigment complete all as specified.

M&L for 75 mm thick PCC 1:3:6 type C-2 (using 40 mm graded stone aggregate) as in plinth protection, surface finished even and smooth without using extra cement, laid in panels n exc 3 mtr long and joints shall be filled with the mixture of bitumen and sand in (1:3) by weight complete all as specified and directed.

Dismantling of stone slabs & tiles of any description of thickness laid dry and pointed in any mortar, in floors, aprons etc.

M&L for 16 to 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixtureof pigment to match with shade of granite

BHATIA ASSOCIATES