SPECIAL REPAIR TO BLDG NO NP-1 OF CWE OFFICE AND PROVN OF STORAGE ACCN NEAR BLDG NO P-6/1 AT STATION CANTEEN AND CERTAIN MINOR WORK UNDER GE SATWARI

Amount

M & L for surface dressing n exc 15cm deep and getting out in any type of soil complete all as specified.

M & L for surface exacavation n exc 30Cm deep and averaging 15Cm deep and getting out in soft/loose soil complete all as specified.

Dismantling asbestos cement (Corrugated or semi-corrugated) sheets in roof covering complete all as specified and directed.

Dismantling timber scantlings 40 sq. cm and over in section, in any position ( framed work) complete all as specified.

Demolition of brick work built in cement mortar or cement lime mortar incl all quoins, arches pillars etc and removing unserviceable material from the work site ouside defence premises complete all as specified.

Demolition of cement concrete (unreinforced) of any description and in ay position not otherwise specifically provided for nad removing the rubbish from the work site out side defence premises complete all as specified.

M&L for excavation in trenches, not exceeding 1.5 mtr wide and not exceeding 1.5 mtr in depth; for foundation, etc. not exceeding 10 Sqm on plan and not exceeding 1.5 mtr in depth and getting out, in any type of soil, complete all as specified and as directed by Engineer-In-Charge.

M&L for Plain cement concrete 1:4:8, type D-2 (using 40mm graded crushed stone aggregate), as in subbase, mass concrete in foundation, complete all as specified and as directed by Engineer-In-Charge.

Material and labour for RCC Type B1 1:2:4 (20 mm aggregate)as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns complete all as directed.

Material and labour RCC Type B1 1:2:4 (20 mm aggregate) as in columns, pillars, piers, posts and struts etc complete all as specified and directed

Material and labour RCC Type B1 1:2:4 (20 mm aggregate) as in beams, cantilevers, bressummers, chajjas lintel over 1.5 m span completed all as specified ad directed.

Material and labour RCC Type B1 1:2:4 (20 mm aggregate)as in in slabs supported on walls beams and columns in floors, roofs, landings, balcony, canopies, deck slabs and in slaves and like completed all as specified ad directed.

Use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for rough finished surfaces complete all as specified and as directed by Engineer-In-Charge.

Use and waste of formwork to sides of pillars, posts, struts, pier, column square, rectangular or polygonal rough finished surface of concrete

Use and waste of formwork to chullah hoods, chajjas troughs and similar items including edges.

Use and waste of formwork to sides and soffits of floor or roof beams, beam haunching, girders, bressummers, lintels, cantilevers, shelves etc with fair finished surface of concrete.

Use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for rough finished surfaces complete all as specified and as directed by Engineer-In-Charge.

Use and waste of formwork to edges of concrete flats, treads, breaks in floors,window cills, concrete rail­ings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizon­tal or sloping and similar work exc 10cm but n exc 20cm wide for rough finished surfaces complete all as specified and as directed by Engineer-In-Charge.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25Cm, complete all as specified and directed by Engineer-In-Charge.

Spreading and levelling in layers n exc. 25 cm thick,watering and well ramming in layers as in floors with earth obtained from excavation complete all as specified and directed by Engineer-In-Charge.

Removing excavated materials/ soils, to a distance not exceeding 50mtrs and depositing where directed at a level not exceeding 1.50mtrs, complete all as specified and directed by Engineer-In-Charge.

Material and labour for hardcore of broken stone of gauge n.exc 63mm, deposited spread and leveled in layers n.exc 15cm thick watered and well rammed to a true surface, complete all as specified and directed

M&L for Brick work with subclass 'B' bricks, old size bricks, straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6 complete all as specified and as directed by Engineer-in-charge

M&L for Brick work with subclass 'B' bricks, old size bricks, straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6 but except bricks complete all as specified and as directed by Engineer-in-charge

M&L Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 all as specified.

TMT bars 10 mm and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed by Engineer-In-Charge.

TMT bars 5 mm and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips in stirrups, spacers and builders.

Ditto all as per item No 26 above but 5 to 10mm dia as in stirrups & links etc.

M&L for 75mm thick PCC 1:4:8, type D-2 (using 40mm graded crushed stone aggregate), as in subbase, of floor,complete all as specified and as directed by Engineer-In-Charge.

M&L for Plain cement concrete type B-0(1:2:4), (using 12.5mm graded crushed stone aggregate), nominal mix, 25 mm thick, as in floors, finished even and fair complete all as specified and as directed by Engineer-In-Charge.

Material and labour Non-skid Digital Ceramic joint less coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm , in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match and set in neat cement slurry and pointed with coloured/white cement to match the surface over and including 15 mm thick screed bed in CM 1:4 complete all as specified. Make : Somany, Kajaria, Sun Hert, Cera ( sample as approved & kept in GE's sample room)

Material and labour glazed ceramic coloured Digital tiles in vertical surface 300x450x7 mm thick, set and jointed in neat cement slurry and pointed white or colored cement to match the surface over and including 10 mm thick CM 1:4 all as specified. Make : Somany, Kajaria, Sun Hert, Cera (Sample as approved & Kept in GE's sample room)

Material and labour for rendering 15mm thick on other than fair faces of brick work or concrete surfaces in cement mortar 1:4 finished even and smooth without using extra cement complete all as specified.

Material and labour for rendering 10mm thick fair faces of brick work or concrete surfaces in cement mortar 1:6 finished even and smooth without using extra cement complete all as specified.

M&L for Rendering 10 mm thick on fair faces of brick or concrete surface ceilings, in cement mortar 1:3 , rendering is to be finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-charge.

Material and labour for rendering 5 mm thick on fair faces of brick work or concrete surfaces in ceiling in cement mortar1:3 finished even and smooth without using extra cement complete all as specified.

Rendering 15mm thck in CM 1:4 mixed with integral Water proofing compound on concrete surface in roofs ,complete all as specified and as directed by Engineer-In-Charge.(IWPC shall be measured and paid separately)

Supply and fixing Box type Steel windows comprised of tubular frame and shutters made out of 1.25mm thick MS steel tube factory made with double side shutters wire gauged shutter & glass glazed shutter ( wire and glass panes shall be measured and paid separately ) with side hung shutters with steel handle and steel peg stay dovetailed ot welded incl 2 Nos tower bolts 150mm long for each leaf and 8mm square bar grills at spacing as shown on drg welded to F I frame work , incl other fittings ,hinges ,handles tarred hold fasts PCC blocks etc. all as shown on drg No CEPZ /TD-354/09 sheet 1/3 to 3/3 complete

Supply only water proofing compound liquid.

S&F Vitreous China, wash basin white, flat back, size 550mmx400 including brackets of any size, including cutting for and pinning in ends of brackets or erecting stand including fixing and supply of waste pipe of 32 mm dia, waste coupling of chromium plated brass complete all as specified and as directed by Engineer-in-charge. Make :- Cera, Cat No- S2040119 or equivalent in Jaquar/ Hindware.

S & F tubular towel rail, 20mm dia, D type, 60cm long between flanges, chromium plated fixed to walls with chromium plated brass screws, fixing in repairs, complete all as specified and as directed by Engineer-In-Charge.

Material and labour for Vitreous China squatting pan 'Orissa' pattern size 580x440mm white with integral foot rest with 'P' or 'S' trap (excluding flushing cistern and flush pipe) and provision of lime concrete and making good floor, all as specified.

Supply and fixing 10 litres capacity PVC valve less, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets including PVC flushing pipe 32mm bore as required and a pair of bracket etc complete all as specified

S&F Urinal (CAPRIANA in white colour,) half stall with complete accessories Set, CP Waste Coupling, PVC waste pipe, sprader etc. Size: 375 x 390 x 590 mm complete all as specified. Make:- Cera, Cat No- S4020112 or equivalent in Jaquar/ Hindware.

M & L PVC (SWR) pipes, 110 mm bore, single socketed, in any length with rubber ring joints, laid in trenches/fixed on walls complete all as specified and as directed by Engineer-In-Charge. Make -Astral, Supreme, Finolex

M & L PVC (SWR) pipes, 75 mm bore, single socketed, in any length with rubber ring joints, laid in trenches/fixed on walls complete all as specified and as directed by Engineer-In-Charge. Make -Astral, Supreme, Finolex

M & L PVC (SWR) bends of 110 mm bore, any radius, complete all as specified and as directed by Engineer-In-Charge. Make -Astral, Supreme, Finolex

M & L PVC (SWR) bends of 75 mm bore, any radius, complete all as specified and as directed by Engineer-In-Charge. Make -Astral, Supreme, Finolex

M & L PVC (SWR) floor trap, plain with grating including jointing with solvent cement for bore of pipe 75 mm dia complete all as specified and as directed by Engineer-In-Charge. Make -Astral, Supreme, Finolex

S & F Salt glazed stone ware gully traps square mouthed, type 'P' 150mm x 150mm including excavation and earth work, set in PCC M-10 (Nominal mix) block measuring 45cm x 45cm and cast iron grating including jointing in cement mortar (1:1), complete all as specified.

S & F Rotational moulded polyethylene water storage tanks of 500 liters capacity,triple layered white colour (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I including ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed for 20mm bore pipe, complete all as specified and as directed by Engineer-in-Charge.

Supplying, laying, jointing & testing galvanised steel water tubing 15 mm bore medium grade with screwed joint together with all fitting such as bends, elbows, tees, short pieces and union etc fixed to walls or laid in floors including all fittings complete all as specified and directed.

Supplying, laying, jointing & testing steel water tubing 20 mm bore medium grade with screwed joint together with all fitting such as bends, elbows,tees,short pieces and union etc fixed to walls or laid in floors including all fittings complete all as specified and directed.

S&F fancy type CP stop valves,/angle valves concealed type,cast copper alloy,chromium plated with long shank and cup screwed both ends for iron pipe or for unions and fixed for 15mm bore pipe, complete all as specified and as directed by Engineer-In-Charge.

S&F PVC connections 15mm size with PTMT nuts of length 450 mm, complete all as specified and as directed by Engineer-In-Charge.

S& F Pillar taps, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed for 15mm bore pipe,complete all as specified and as directed by Engineer-In-Charge.

S&F 15 mm dia fancy bib tap, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule fancy type screwed for iron pipes with wall flange and aerator.

M & L for plain cement concrete 1:3:6, type C-1 (using 20mm graded crushed stone aggregate), 75mm thick, as in plinth protection and providing the joints throughout the thickness, filled with mastic filling comprising bitumen 85/25 grade and sand mixture 1:3 by weight, complete all as specified and as directed by Engineer-In-Charge.

M&L Mild steel flat & angle iron as in doors or gates frame including, drilling holes, welding , etc and similar work conforming to Fe-290 Gde E-165 etc complete all as specified and directed by Engineer-In-Charge.

S&F Mild steel small articles such as flat iron for hold fasts etc conforming to Fe 290 Gde-E-165, all as specified and as directed.

M&L for PCC 1:2:4 type B 1 using (20 mm graded aggregate) as in blocks for hold fasts, benching, coping apex stones, bed plates and the like including weathering slightly rounded or chamfered angles and throating all as specified and direct. Note: Form work required for these items included in the unit rate of this item.

S&F Butt hinges, size 100mm, medium weight, cold rolled mild steel, and fixed, complete all as specified and as directed by Engineer-In-Charge.

S&F Aluminium anodised, barrel tower bolts of extruded Section, size 150 mm long and fixed, complete all as specified and as directed by Engineer-In-Charge.

S&F Aluminium handles, cast type, anodised, size 150 mm, complete all as specified and as directed by Engineer-In-Charge.

M & L for two coats of synthetic enamel paint over a coat of red oxide primer on new steel surfaces including preparation of new surface over 10cm width or girth complete all as directed by Engr-in-Charge

M&L for applying one coat of synthetic enamel paint on old painted steel surfaces of any description having width/girth exceeding 10 cm including preparation and rubbing with sand paper to make surface even and smooth and apply putty and primer where requred complete all as specified.

S & F galvanized mild steel wire cloth of 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tack or galvanized wire staples complete all as directed.

M& L 3mm thick sheet glass ordinary quality and glazing with oil putty in area n.exc 0.5 sqm each pane complete all as specified.

S&F 3 mm thick figured glass, pin head type and glazing with oil putty in square n.exc 0.5 sqm in each pane.

Preparation of new plastered or unplastered surfaces of walls and applying three coats of white washing, complete all as specified and as directed by Engineer-In-Charge.

Preparation of new plastered or unplastered surfaces of ceiling and applying three coats of white washing, complete all as specified and as directed by Engineer-In-Charge.

Preparation of new plastered or unplastered surfaces of walls and applying two coats of cement based paint over and including one coat of primer, complete all as specified and as directed by Engineer-In-Charge.

M&L for preparation of old decorated plastered /concrete/ brick surfaces of walls (up to 4th storey with necessary scaffolding) and applying one coat of cement based paint on old decorated surfaces including preparation.

Taking down cement plaster of any description on brick or stone walls or from concrete surface including raking out joints, hacking for key, scrubbing down with water etc, and removing unserviceable material outside cantt area, complete all as specified.

M&L for Vitrified Ceramic(Double Charged) edge cut joint free coloured or printed any shade tiles 10 mm thick (square/ rectangular) polished area of each tiles exceeding 0.18 sqm but not exceeding 0.38 sqm , in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match and set in neat cement slurry and pointed with coloured/white cement to match over and including 15 mm thick screed bed in CM 1:4. complete all as specified and as directed. Make : Somany, Kajaria, Orient, Bell ( sample as approved & kept in GE's sample room)

Description all as item No 76 but as in vertical surfaces dado/skirting over and including a backing coat of CM 1:4, 10 mm thick complete.

M&L 16 to 18 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, over and including 20 mm thick CM 1:4 as directed by Engr-in-charge.

M&L Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified.

M&L 150 mm bore/Inner Dia. Double wall corrugated HDPE Pipes (SN4) with integral socket and necessary fittings, laid in trenches jointed complete all as specified. Make : Astral, Supreme, Prince.

M&L Providing precast cement concrete Type B1, 1:2:4 ( 20 mm graded aggregate) in landings, cover slabs (for man holes etc.) for septic tank and incld necessary form work and set in cement mortar 1:6 complete all as specified.

M&L Cutting into existing manholes for connecting new drains, making good to pipe ( Internal dia 150 to 200mm ) and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required.

S&F Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified. Make:- Jindal ( JSW), TATA, SAIL, Indian Ispat

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified. Make:- Jindal (JSW). TATA, Indian Ispat

S&F structural steel work conforming to Fe-410-W (Gde E-250 Quality-A or B) or Fe-290 Gde E-165, as in roof trusses (framed), purlins, crane gantries, rails, vertical post and fastenings, heavy brackets framing (Beam, tee, angle, channel, square hollow section or flat section) including distance pieces, cleats etc complete all as specified.

All as per Srl Item No. 85 here-in-before but in main and cross beam, hip and jack rafters, purlins, plates (plain or chequered), channels, square cut or notched etc.

Dismantling of ceiling board (Fibre,pulp,any type of insulation etc) or insulation board / slabs/any thickness including cover fillets and snap grids complete all as specified and directed

Supply and fixing in repair GI snap grid frame work (Grid size 605cm x 605cm) for false ceiling consisting of main runner 'T' of size 24mm x 32mm and 0.3mm thick , Secondary runner 'T' of size 24mmx25mm and 0.3mm thick,GI angle 24mmx24mm and 0.4mm thick,Bottom exposed capping of width 24 mm of all T-sections shall be of 0.25mm thick PPGI, hot dipped galvanised steel with zink coating not less than 120gm / Sqm ,ceiling grid system duly suspended by 4mm dia GI wire hanging from existing purlins /roof slab with butterfly clips including Gypsum ceiling tiles of size 595 x 595 x 7 mm laminated with 0.07 mm thick polyvinyl film on the face side and 10 micron metalized polyester film on the back side fixed on GI snap grid complete all as specified and directed by Engr-in- Charge. Make : Gyproc, Lafarg boral Gypsum India, India Gypsum

M&L for preparation of old decorated concrete/ plastered surfaces of walls, Pillars, cornices etc by booming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots & rubbing with sand paper and applying two coat of oil bound distemper on old decorated wall surface including two coats of wall care putty of 1 to 2 mm thick on uneven surface as and where required.

Material ad labour for preparation of new plastered surfaces of walls & applying two coats of oil bound distemper over two coat of wall care putty of 1 to 2 mm thick and one coat of primer complete all as specified.

M&L for preparation of old decorative plastered/concreat surface of wall, chajja, facia, face of columns, beam ect by booming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots & rubbing with sand paper and applying one coat of weather proof exterior emulsion (APEX) with necessary scaffoding up to 4th storey, including necessary filling of wall care putty on uneven surface as and where required all as specified.

Taking down chowkats or frames with shutter (without taking off shutter from the frame) exc 1.5 Sqm & n.exc 4 Sqm each including cutting holes for taking out hold fast or dismantling brick work and removing from site all as specified.

M&L for 40 mm thick PCC 1:2:4 Type B-0 (using 12.5 mm crushed stone aggregate) as Damp proof course to horizontal or vertical surfaces including necessary formwork .

S&F powder coated anodised aluminium frame for doors, window, ventilators/partition with one or more rebates including joining cleat for fixing etc. ( Minimum thickness of powder coating 50 micron ) complete all as specified.

S&F powder coated anodised alumunium door shutters, thickness of powder coating not less than 50 micron, alumunium section weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handle 02 Nos in each door, hinges, anodised aluminium snap beading, screws etc. for fixing of glass/ACP inserts complete all as directed by Engr-in-charge and as approved by GE.

Powder coated anodised aluminium window and ventilator shutters, aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door,hinges, anodised aluminium snap beading, screws etc for fixing glass/ACP inserts thickness of powder coating not less than 50 micron, complete all as specified.

Anodised aluminium grills, 6mm dia size 100x100mm fixed to aluminium windows and thickness of powder coating not less than 50 micron, complete all as specified.

S&F 4mm thick alumunium composit panel (coloured Sheet) and in additional other accessories for fitting, complete all as specified and directed.

S&F 5.5 mm thick glass sheet ordinary quality plain and glazed in squares, glazing with beads fixed with metal panel in square in n exc 0.5 sq.m in each pane etc complete all as specified and directed

S&F 5.5 mm thick glass sheet ordinary quality coloured/tinted/frosted and glazed in squares, glazing with beads fixed with metal panel in square in n exc 0.5 sq.m in each pane etc complete all as specified and directed.

S&F door closer hydraulically regulated, designation No 1, Aluminium extruded section body universal type, suitable for door shutters of 700 mm in width and of weight not more than 35 kg and fixed, complete all as specified. Make : Everest, Universal, Godrej

M&L for double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed. Make : Everest, Universal, Godrej

S&F mortice lock with brass body, 4 lever vertical type , size 100mm etc complete Make : Godrej, Harrison, Link

S&F repair 25mm outer dia stainless steel decorative drapery rod of thickness 20 gauge and for every 01 RM length, with stainless steel brackets near to ends with stainless steel finials for 25mm dia drapery rod at both ends. The drapery rod shall be projecting 150 mm outer side from the clear opening of doors/windows. ( Including necessary fittings)

M&L for Plain Cement concrete (1:3:6) type C-1 using 20 mm graded crushed stone aggregate as in surface channels and drains including necessary formwork complete all as specified and as directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc. complete all as specified and as directed by Engineer-in-charge

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm Plain colour PVC sheet reinforced with mild steel square tube, supplying and fixing in opening as per specifications and drawing including making good to disturbed surface of walls, complete all as specified and as directed by Engr-in-Charge. Make :- Rajshri Plastiwood Ltd,Sintex & M/S Fenesta

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppplying and fixing in the frame at site as per specification & drawing complete all as specified and as directed by Engr-in-Charge. Make :- Rajshri Plastiwood Ltd, Sintex & M/S Fenesta

Taking down carefully aluminium conductor point wiring (light, fan, socket, power socket) complete fitting such as swithes, sockets, lamp holder, utility light fitting, fan regulator etc and removing materials from sites and making good distrubed surface of walls and roofs complete all as specified and as directed.

Point wiring with 1.5 Sqmm single core multi stranded copper conductor FRLSH insulated and unsheathed heavy duty cable in colour code including contineous earth wire with cable of size 1.5 sqmm copper conductor flexible FRLSH insulated drawn in and including concealed PVC rigid conduit medium grade ISI marked after cutting chases in wall, plastering after concealing conduit, terminated into modular galvanised flush boxes of suitable size including white cover plate with frame as per relevant IS for mounting modular switches, sockets, fan regulators etc complete all as specified and as directed for the following :- (a) One light/fan/bell point controlled by one, one way switch modular type 6 Amp .

(b) One 3 pin socket outlet on independent Board controlled by one one way modular switch 5 Amp

(c) One 3 pin 5 Amps socket outlet on same board controlled by one, one way 5 Amps modular switch.

All as per srl item No 110 above but for one 3 pin socket outlet 16 Amp independent with cable of size 2.5 Sqmm for point wiring and 2.5 sqmm as in continuous earth wire.

M&L for complete point wiring with 1.5 Sqmm single core multi stranded copper conductor FRLSH insulated and unsheathed heavy duty cable in colour code including continuous earth wire with cable of size 1.5 sqmm copper conductor flexible FRLSH insulated drawn in existing conduit matching the white wash colour with existing colour terminated into including suitable module modular metal flush boxes of Make : Elvira Indoasian or equivalent in list of make including white cover plate with frame as per relevent IS for mounting switches, sockets, fan regulators etc complete all as specified and as directed for the following :- (a) One light/fan/bell point controlled by one, one way switch modular type 6 Amp .

(b) One 3 pin socket outlet on independent Board controlled by one one way modular switch 5 Amp

Ditto all as per Srl item No 114 above but for one 3 pin socket outlet 15/16 Amps independent with cable of size 2.5 Sqmm for point wiring and 2.5 sqmm as in continuous earth wire in existing conduit including cutting chasing for fixing of GI modular sunken box all as specified and directed. Note : GI sunken boxes and white cover sheet to be measured and paid separately.

Modular type switch, one way 6 Amps , 1 module complete all as specified and directed.

Modular type socket 5 pin, 6 Amps 2 module complete all as specified and directed.

Modular type switch, one way 16 Amps, 1 module complete all as specified and directed.

Modular type socket 5 pin, 6 A/16 Amps 2 module complete all as specified and directed.

Modular type fan regulator step down 120 Watt, 2 module complete all as specified and directed.

Ceiling rose surface, backelite, three terminal, 240 volts complete all as specified and directed.

LED tubelight fitting for 18-20 Watt LED, 230V, Batten type complete in all respect . Cat Part No DMLN1LT8-16 in Crompton or Cat Part No WIO921208 of Wipro, along with LED Tube Rod Polycarbonate with superior aesthetic and heat dissipation capability suitable for G-13 base tube lights base fluorescent T8-T12 luminaire, 18-20 watt LED wattage with colour temp of 6000K 1800 lumens and with surge arrestor complete in all respect. Cat part NO LTT 8-20 of Crompton or LL13-181-650 of Wipro or equivalent in list of makes. Note : The LED batten and LED tube rod shall be of same make.

Supply and fix in replacement of LED wall mounting tube light fitting 10 Watts LED Complete fitting with all fixing arrangement all as specified and directed.

Supply and fix Vertical Distribution Board (TP & N) 4 way double door suitable for and MCCB four pole as incomer and out going MCBs and should be IP43 protected with Copper Busbars, Neutral links, Earthing Bar all as specified and directed: Note: (i) MCCBs FP & SP shall be measured paid separately (ii) MCB & DB shall have the same make.

Supply and fix 4 pole MCCB 100 Amp, 415 Volts with rupturing capacity 16 KA, complete all as specified and directed.

Supply and fix Distribution Board (SPN) double door 8 way and should be IP 43 protected with Cooper Bus Bar, Earth Bar, Neutral Bar door Earthing all as specifieed and dirceted.

Supply and fix Distribution Board (SPN) double door 4 way and should be IP 43 protected with Copper Bus Bar, Earth Bar, Neutral Bar Door Earthing all as specified and directed.

Supply and fix MCB SPN complete 32 to 63 Amp with rupturing capacity 10 KA 'C' series, complete all as specified and directed

Supply and fix MCB Single pole 6 to 32 Amp with rupturing capacty 10 KA 'C' series, complete all as specified and directed.

Sub main wiring with single core cable 2x 10 sq mm FRLSH insulated Unsheathed stranded copper conductor cable 1100 Volts grade in rigid PVC conduit (Concealed) medium grade alongwith 1 x 10 Sq mm FRLSH insulated unsheathed copper conductor cable as earth wire connected with main earth dolly including chesing, cutting & making good to match with the existing surface complete all as specified and directed.

Sub main wiring with single core cable 2x 16 sq mm FRLSH insulated Unsheathed stranded copper conductor cable 1100 Volts grade in rigid PVC conduit (Concealed) medium grade alongwith 1 x 16 Sq mm FRLSH insulated unsheathed copper conductor cable as earth wire connected with main earth dolly including chesing, cutting & making good to match with the existing surface complete all as specified and directed.

Sub main wiring with single core cable 4x 16 sq mm FRLSH insulated Unsheathed stranded copper conductor cable 1100 Volts grade in rigid PVC conduit (Concealed) medium grade alongwith 4x16 Sq mm FRLSH insulated unsheathed copper conductor cable as earth wire connected with main earth dolly including chesing, cutting & making good to match with the existing surface complete all as specified and directed.

Supply and fixing of PVC body exhaust Fans 250 mm Sweep, single phsae AC 220/240V, with energy efficient motor, pre lubricant double ball bearing, speed 900 RPM white color complete louvers for wall mounted incl grounting, holding down bolts, nuts washers and provision of flexible coper conductor cable 3 core from ceiling rose to exhaust fan alongwith plastering, finishing, painting and making good distributed surface complete alla s specified and directed by Engr in charge.

Lamp holder,PVC /Polycarbonate type with back plate for batten fitting .

Earthing complete with galvanised mild steel earth plate electrode of size 600x600x6mm thick burried directly in ground earth (in vertical) earth pit not less than 2.25 mtr deep below normal ground level with top edge of the earth plate not less than 1.5 mtr below ground level connected to galvanised iron or earth lead wire 4mm dia (8 SWG) by means of nut, bolt, check nuts and washer of galvanised ironl including PCC pit in PCC 1:2:4 type B-1 pre-cast RCC cover slab using reinfocement with XPM weighing not less than 1.87 kg/Sqm with suitable handle made of 12mm round bar, including necessary excavation and earth work in any type of soil, 20mm dia medium grade galvanised steel tube for watering with one end fixed with cast iron funnel and wire mesh 15mm dia bore light grade galvanised steel tubing upto 7.5 m length for drawing earth lead wire protection, common salt, charcoal, etc complete all as shown in electrical plate No 3 of SSR Part-I and testing on completion.

Energy saving new generation 10W LED IP65 bulk head luminaire with opal diffuser complete all as specified and directed. Make : Havells Cat Part No LHEOAOP7UZ6W010 or equivalent in Crompton/ Philips/ Wipro

Supply laying of underground LT cable 1100 volts grade heavy duty electric cable XLPE insulated and PVC outer sheathing with aluminium stranded conductor, armoured cable 16 Sqmm 2 core cable confirming to IS-7098 Part-I (1988) with latest amendments complete all as specified.

Dry sand for cushioning to cable by providing with a layer of sand 8cm deep before laying the cable and 15cm deep after laying and stretching the cable in trenches complete all as specified and as directed by the Engineer-in-Charge.

Sub class `B` bricks laid dry flat transversely along the length of cable with width equal to the length of bricks over sand cushioning as protection cover of cable laid.

M&L for tube light grade galvanised with all fitting and fixed complete to wall and ceiling or laid in floors of size 40mm dia.

Supply and fix LED lamp suitable for B22 holder of capacity 7 Watt.

Supply & fix of exhaust fan steel body AC single phase 230V of size 300mm sweep with blades and frame and louvers and including making of holes in wall floor etc all as directed by Engr-in-charge.

Supply and fixing gun metal gate / globe valve screwed both ends for iron pipe of 20mm bore ISI marked all as specified and directed.

Supplying installation, commissioning and testing of servo controlled automatic voltage stabilizer (confirming as per BIS: 9815, Pat-I 1994 reaffirmed 2009) for automatic operation of capacity 50 KVA, in door type, 3 phase, 4 wire, 50 Hz naturally oil cooled, unbalanced type copper wound, digital display type, relay free smooth and silent operation with 1st filling of transformer oil (IS335/1993 reaffirmed 2005) having following specifications:- (i) Input voltage 300V-480V. (ii) Output voltage stabilized at 415V un + 1% (adjustable). (iii) No distortion in wave form. (iv) Response time not to exceed 10 milliseconds. (v) Senstivity +1%. (vi) Rate of correction 8 volts/second for single phase and 20 volts/second for phase to phase. (vii) No load lossed less than 0.5% (viii) Full load losses less than 2.5% (ix) Duty cycle-continuous 24x7. (x) Efficiency more than 95%. (x) Type of load: 3 phase unbalanced type. (xi) Digital display voltmeter/ammeter (xii) Capacity 50 KVA. Protections : 1. Overhead/short circuit protections 2. High/low voltage cutoff 3. Bypass arrangement in case of emergency 4. Single phase sequence change protection. The stablizer shall be powder coated for water/dust and vermin proof complete as directed by Engr-in-Charge Make: AE/BENTFORD/V GUARD/APLAB/ANDREWYULE/VOLINA.

Supply laying and testing LT XLPE insulated armoured heavy duty electric aluminium conductor PVC sheathed galvanized steel strip or wire, armoured electric power cable, with aluminium stranded conductor 1100 volts grade, cross sectional area, 70 Sqmm 3.5 core laid in trenches/road crossing/under floor /on walls/ on poles including testing complete all as specified directed by Engr-in-charge.

Supply and fixing manual change over switch 415 volts in sheet metal enclosure 4 pole of capacity 125 Amp all as directed by Engr-in-charge.

Supply and fixing ceiling fans complete with blade, down rods, electronic regulator socket type 5 step (rorary type) including necessary wiring in existing switch board and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) andconnected from ceiling rose/ connector with & including suitable size flexible copper conductor PVC insulated sheathed cord, complete with hook type anchor fastener to hanging of ceiling fan all as directed by Engr in charge.

Supply & fix 25mm dia rigid non-metallic PVC conduit medium grade ISI marked including concealed in wall/ceiling/roof of boxes (junction/terminal), tees, bends, elbows, reducers, bell mouth, tube ends and fixing accessoies such as couplers, lock nuts, saddles, pipe hooks etc complete all as specified and directed for TV/telephone.

M/S A TO Z ENGINEERS

Azurite Engineering

M/S MOHAN LAL GUPTA

M/S PARAMJEET SINGH

M/S ANIL MAHAJAN